The etop driver is used by all targets except xrx200.
Remove the UBIFS compression support for zlib and zstd from the xway
subtarget. The hardware is EOL for a long time and it's unlikely to ever
see a board shipped with an UBIFS using these compression methods.
Remove the JFFS2 support. Support for jjfs2 images was dropped years
ago.
It shrinks the compressed kernel up to 130 KByte.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Switch to the mainline Lantiq PCIe PHY driver and update the vr9.dtsi
accordingly.
The Lantiq IRQ SMP support added upstream required changes to the SoC
dtsi as well.
Following changes are made to the Lantiq kernel patches:
0005-lantiq_etop-pass-struct-device-to-DMA-API-functions.patch
0006-MIPS-lantiq-pass-struct-device-to-DMA-API-functions.patch
applied upstream
0008-MIPS-lantiq-backport-old-timer-code.patch
access_ok API update because it lost it's type (which was the first)
parameter in upstream commit 96d4f267e40f95 ("Remove 'type' argument
from access_ok() function")
0024-MIPS-lantiq-autoselect-soc-rev-matching-fw.patch
merged into 0026-MIPS-lantiq-Add-GPHY-Firmware-loader.patch
0024-MIPS-lantiq-revert-DSA-switch-driver-PMU-clock-chang.patch
revert upstream changes required for upstream xrx200 ethernet and
xrx200 (DSA) switch driver but breaking our driver
0026-MIPS-lantiq-Add-GPHY-Firmware-loader.patch
required for our driver but dropped upstream, add former upstream
version
0028-NET-lantiq-various-etop-fixes.patch
now has to use the phy_set_max_speed API instead of modifying
phydev->supported. Also call ltq_dma_enable_irq() in
ltq_etop_open() based on upstream commit cc973aecf0b054 ("MIPS:
lantiq: Do not enable IRQs in dma open")
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Duplicate kernel 4.19 config and patches for kernel 5.4.
Duplicate the devicetree source files as well, they need kernel 5.4
specific adjustments.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This reorganizes 02_network board.d files based on what's done for
ath79 and ramips: Instead of putting all settings into a single big
case, the interface/dsl/MAC address setup is put into separate
functions with a specific switch case for each of them. This makes
grouping of devices much easier and should be easier to read, too.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
DSL setup consists of the same commands for all subtargets, so move it
into a helper function.
While at it, remove shebang from library file.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This splits the device-dependent base-files into subtarget directories,
like done recently for ath79 and ramips. While this increases the
overall lines of codes, it will make the code per subtarget smaller
and easier to keep track of features and devices.
While at it, several variables at the top of 02_network are removed,
as they were never changed. The values are put directly into the
function calls where they are used.
Remove unneeded LED setup from 01_leds, and remove 01_leds entirely
for falcon subtarget (as it is not used there).
Applies alphabetic reordering to device cases in base-files.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The current state of the kernel 4.14 support is in the openwrt-19.07
branch. No need to keep a not default used kernel in this branch.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This just copies the files from the kernel 4.14 specific folders into
the kernel 4.19 specific folder, no changes are done to the files in
this commit.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This just copies the patches, configuration and dts files into the
directories hich are used for kernel 4.14.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Move the devicetree source files to a kernel specific directory in
preparation of adding kernel 4.14 support.
Rename the subtarget kernel config files to match a specific kernel
version.
Signed-off-by: Mathias Kresin <dev@kresin.me>
To make it more accessible for nodejs users to configure and run a build
on mips target lacking hardware fpu
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Add the missing USB related kernel config options to target config.
Enable wireless as well, wireless is supported via USB.
Fixes compile/packaging errors with the libertas wireless kernel
module.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Do not disable SPI in the subtarget, otherwise the SPI driver can not
be used.
Disable SPI by default and enable it in the board specific device tree
source file.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The subtarget kernel config options CONFIG_CC_OPTIMIZE_FOR_SIZE and
CONFIG_HAVE_IRQ_EXIT_ON_IRQ_STACK are already set by the target or
global kernel config.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch sets the cflags -mtune=34kc -mdsp only in XWAY subtarget, while the others remain with mtune=mips32r2.
Although the Danube has a Mips 24KEc core performs well with the above cflags.
Signed-off-by: José Vázquez Fernández <ppvazquezfer@gmail.com>
SVN-Revision: 37006
