- Add new tsens node
- Add new cpufreq required nodes
- Drop arm cpuidle compatible
- Fix duplicate node set upstream
- Add voltage tolerance value for cpu opp
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
ipq806x have different ecc configuration for boot partition and rootfs partition. Add support for this to fix IO error on mtd block scan.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
The spm driver now has dedicated support for krait cpu idle state. We don't need to add generic arm cpuidle support for qcom.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Patch 0030 wrongly disables gsbi1 instead of gsbi4.
Fix the wrong patch and also include other fix from the original qsdk source.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Various report and data show that the freq 384000 is too low and cause some
extra latency to the entire system. OEM qsdk code also set the min frequency
for this target to 800 mhz.
Also some user notice some instability with this idle frequency, solved by
setting the min frequency to 600mhz. Fix all these kind of problem by
introducing a boot init.d script that set the min frequency to 600mhz and set
the ondemand governor to be more aggressive. The script set these value only if
the ondemand governor is detected. 384 mhz freq is still available and user can
decide to restore the old behavior by disabling this script.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
This was introduced to gmac2 and gmac3 in 57ea767a53 without fanfare.
There's no indication of why it was added to those devices, but not to
gmac0 or gmac1. It was probably an unintentional omission. It should be
present on all four gmac devices.
This property is considered by
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
stmmac_probe_config_dt.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
Build-tested: ipq806x/ubnt,unifi-ac-hd
Run-tested: ipq806x/ubnt,unifi-ac-hd
The Ubiquiti UniFi AC HD (UAP-AC-HD, UAP301) has two Ethernet ports,
labeled MAIN and SECONDARY, connected to gmac2 and gmac1, respectively.
The standard probe order results in gmac1/SECONDARY being eth0 and
gmac2/MAIN being eth1. This does not match the stock firmware, is
contrary to user expectation, causes the wrong (high) MAC address to be
used in a bridged configuration (the default for this device), and makes
the gmac2/MAIN port unusable in the preinit environment (such as for
failsafe). Until a recent patch, gmac1/SECONDARY (eth0) was not even
usable.
This reorders the ports so that gmac2/MAIN is eth0, and the now-working
gmac1/SECONDARY is eth1. eth0 has the low MAC address and eth1 has the
high; when bridged, the bridge takes on the correct low MAC address.
This matches the stock firmware. The MAIN port is usable for failsafe
during preinit.
This device does not have a switch on board, so there's no possibility
to remap ports via switch configuration. "ip link set $interface name"
is used instead, during preinit before networking is configured.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
Build-tested: ipq806x/ubnt,unifi-ac-hd
Run-tested: ipq806x/ubnt,unifi-ac-hd
Unlike many ipq806x devices, Ubiquiti UniFi AC HD (UAP-AC-HD, UAP301)
has no switch on board. Its two Ethernet ports are connected to Atheros
AR8033 PHYs. It is not appropriate to use fixed-link in this
configuration. Instead, configure the correct PHYs in the device tree
configuration to allow the at803x driver to load.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
Build-tested: ipq806x/ubnt,unifi-ac-hd
Run-tested: ipq806x/ubnt,unifi-ac-hd
On a Ubiquiti UniFi AC HD (ubnt,unifi-ac-hd, UAP-AC-HD, UAP301), a
forced speed on gmac1 is set in the QSGMII PCS_ALL_CH_CTL register,
presumably by the bootloader (4.3.28), preventing the interface from
being usable. The QSDK NSS GMAC driver takes care to clear the forced
speed in nss_gmac_qsgmii_dev_init
(https://source.codeaurora.org/quic/qsdk/oss/lklm/nss-gmac/tree/ipq806x/nss_gmac_init.c?h=nss
at d5bb14925861).
gmac1 is connected to the port on the device labeled SECONDARY, and is
currently eth0 but will be switched to eth1 by a subsequent patch. By
clearing the QSGMII PCS forced speed during dwmac initialization when
SGMII is in use, this port becomes usable.
This patch is upstreamable, and will be sent upstream after successful
testing in OpenWrt.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
Build-tested: ipq806x/ubnt,unifi-ac-hd
Run-tested: ipq806x/ubnt,unifi-ac-hd
Some targets select HZ=100, others HZ=250. There's no reason to select a higher
timer frequency (and 100 Hz are available in every architecture), so change all
targets to 100 Hz.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
For the targets which enable ubifs, these symbols are already part of the
generic kconfigs. Drop them from the target kconfigs.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Ran update_kernel.sh in a fresh clone without any existing toolchains.
Manually rebased:
pending-5.4/611-netfilter_match_bypass_default_table.patch
The upstream change affecting this patch is the revert of an earlier
kernel commit. Therefore, we just revert our corresponding changes
in [1].
Build system: x86_64
Build-tested: ipq806x/R7800
[1] 9b1b89229f ("kernel: bump 5.4 to 5.4.86")
Signed-off-by: John Audia <graysky@archlinux.us>
[adjust manually rebased patch, add explanation]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
1. Use upstream accepted NVMEM patches
2. Minor fix for BCM4908 partitioning
3. Support for Linksys firmware partitions on Northstar
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
ZyXEL NBG6817 comes with an eMMC which contains a GPT partition named
'rootfs_data'. This currently confuses fstools and makes it pick that
(not suitable) partition.
Use the newly introduced fstools_ignore_partname=1 kernel cmdline
parameter to have fstools ignore that partition.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The bootloader of many ipq806x boards seems to require the config node
of the FIT image to be 'config@1' (or a secific different value).
This requirement used to be implicitely satisfied because OpenWrt used
to also call the configuration node inside a FIT image 'config@1'.
However, as recent U-Boot now prohibits the use of the '@' symbol as
part of node names, this was changed by
commit 5ec60cbe9d ("scripts: mkits.sh: replace @ with - in nodes")
Explicitely restore the default name of the configuration node to
'config@1' on ipq806x.
(ipq807x is unaffected as DEVICE_DTS_CONFIG default is set
"config@hk01" in target/linux/ipq807x/image/Makefile)
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
So far, board.d files were having execute bit set and contained a
shebang. However, they are just sourced in board_detect, with an
apparantly unnecessary check for execute permission beforehand.
Replace this check by one for existance and make the board.d files
"normal" files, as would be expected in /etc anyway.
Note:
This removes an apparantly unused '#!/bin/sh /etc/rc.common' in
target/linux/bcm47xx/base-files/etc/board.d/01_network
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
5.4.102 backported a lot of stuff that our WireGuard backport already
did, in addition to other patches we had, so those patches were
removed from that part of the series. In the process other patches were
refreshed or reworked to account for upstream changes.
This commit involved `update_kernel.sh -v -u 5.4`.
Cc: John Audia <graysky@archlinux.us>
Cc: David Bauer <mail@david-bauer.net>
Cc: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
This adds the latest version of ofpart commit. It hopefully
1. Doesn't break compilation
2. Doesn't break partitioning
(this time).
It's required to implement fixed partitioning with some quirks. It's
required by bcm53xx, bcm4908, kirkwood, lantiq and mvebu.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The variables KERNEL_INITRAMFS_PREFIX and KERNEL_PREFIX are already
defined in include/image.mk and don't have to be redefined in the
target Makefiles.
Signed-off-by: Paul Spooren <mail@aparcar.org>
[also cover imx6]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This replaces a full-text BSD clause by the corresponding SPDX
identifier.
This should make it easier to identify the license both by humans
and machines.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
On a platform with many very different devices, like found on ipq806x,
the generic profile seems like a remnant of the past that does not
have a real use anymore.
Remove it to have one thing less to maintain.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
The majority of our targets provide a default value for the variable
SUPPORTED_DEVICES, which is used in images to check against the
compatible on a running device:
SUPPORTED_DEVICES := $(subst _,$(comma),$(1))
At the moment, this is implemented in the Device/Default block of
the individual targets or even subtargets. However, since we
standardized device names and compatible in the recent past, almost
all targets are following the same scheme now:
device/image name: vendor_model
compatible: vendor,model
The equal redundant definitions are a symptom of this process.
Consequently, this patch moves the definition to image.mk making it
a global default. For the few targets not using the scheme above,
SUPPORTED_DEVICES will be defined to a different value in
Device/Default anyway, overwriting the default. In other words:
This change is supposed to be cosmetic.
This can be used as a global measure to get the current compatible
with: $(firstword $(SUPPORTED_DEVICES))
(Though this is not precisely an achievement of this commit.)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This fixes a typo in the previously committed partition map that led to
the extension of the read-only mtd partition "SSD" into the following
partitions.
Fixes: 4e46beb313 ("ipq806x: add support for Ubiquiti UniFi AC HD")
Signed-off-by: Jan Alexander <jan@nalx.net>
Hardware
--------
SoC: Qualcomm IPQ8064
RAM: 512MB DDR3
Flash: 256MB NAND (Micron MT29F2G08ABBEAH4)
32MB SPI-NOR (Macronix MX25U25635F)
WLAN: Qualcomm Atheros QCA9994 4T4R b/g/n
Qualcomm Atheros QCA9994 4T4R a/n/ac
ETH: eth0 - SECONDARY (Atheros AR8033)
eth1 - MAIN (Atheros AR8033)
USB: USB-C
LED: Dome (white / blue)
BTN: Reset
Installation
------------
Copy the OpenWrt sysupgrade image to the /tmp directory of the device
using scp. Default IP address is 192.168.1.20 and default username and
password are "ubnt".
SSH to the device and write the bootselect flag to ensure it is booting
from the mtd partition the OpenWrt image will be written to. Verify the
output device below matches mtd partition "bootselect" using /proc/mtd.
> dd if=/dev/zero bs=1 count=1 seek=7 conv=notrunc of=/dev/mtd11
Write the OpenWrt sysupgrade image to the mtd partition labeled
"kernel0". Also verify the used partition device using /proc/mtd.
> dd if=/tmp/sysupgrade.bin of=/dev/mtdblock12
Reboot the device.
Back to stock
-------------
Use the TFTP recovery procedure with the Ubiquiti firmware image to
restore the vendor firmware.
Signed-off-by: Jan Alexander <jan@nalx.net>
Strictly, an SPDX identifier requires a space between the comment
marker and the identifier itself. This has been addressed in
b69c21738e ("treewide: add space before SPDX identifier"), but
some new malformatted identifiers were merged recently.
This could have been prevented by using checkpatch.pl earlier.
Fixes: 1a775a4fd0 ("ipq806x: add support for TP-Link Talon AD7200")
Fixes: 8ddaeaf642 ("ipq806x: create DTSI for TP-Link AD7200 and C2600")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The TP-Link AD7200 appears with and without the "Talon" model name
prefix. Let's use both variants for 'make menuconfig' so everybody
can locate the device.
Concerning the revision, the TP-Link page lists v1 and v2 with the
device currently marked as "End of Life". However, the v2 and latest
v1 firmware are byte-identical. Thus, we only need one image for
this device and do not need to include the revision in the image name.
While at it, remove the useless BOARD_NAME variable which only makes
sense in combination with upgrade from legacy stable versions or when
custom upgrade scripts are involved.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Both devices share most of their setup except buttons and LEDs,
so having a common DTSI removes a lot of duplicate code.
In order to have a shared partitioning scheme, device-id and
product-info from AD7200 have been merged into a single
product-info partition like for C2600.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This does several cosmetic adjustments for AD7200's DTS:
- Make node name, DT label and label property consistent
- Drop wrong and unused spi4 label
- Use generic flash@0 node name
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
While the underscore in the name of the USB LEDs was removed from DTS,
/etc/board.d/01_leds also has to reflect that change.
Fixes: 28fd279e5d ("ipq806x: some corrections for TP-Link Talon AD7200")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Address most comments made by Adrian Schmutzler on the mailing list.
The device name is kept as 'TP-Link Talon AD7200' as that seems to be
the marketing name TP-Link chose for that device, it also matches the
naming scheme for other TP-Link devices (e.g. 'TP-Link Archer C7').
Fixes: 1a775a4fd0 ("ipq806x: add support for TP-Link Talon AD7200")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Device hardware: https://deviwiki.com/wiki/TP-LINK_AD7200_(Talon)
The Talon AD7200 is basically an Archer C2600 with a third PCIe lane
and an 802.11ad radio. It looks like the Archers C2600/5400 but the
housing is slightly larger.
Specifications
--------------
- IPQ8064 dual-core 1400MHz
- QCA9988 2.4GHz WiFi
- QCA9990 5GHz WiFi
- QCA9500 60GHz WiFi
- 32MB SPI Flash
- 512MiB RAM
- 5 GBit Ports (QCA8337)
Installation
------------
Installation is possible from the OEM web interface.
Sysupgrade is possible.
TFTP recovery is possible.
- Image: AD7200_1.0_tp_recovery.bin
Notes
- This will be the first 802.11ad device supported by mainline.
Signed-off-by: Gary Cooper <gaco@bitmessage.de>
Commit 29ca10e537 ("ipq806x: remove support for kernel 4.19") moved
DTS files to "files" directory, but after that a new DTS file was added
to the former "files-5.4" directory. Move it to the new directory.
Fixes: 98b86296e6 ("ipq806x: add support for ASRock G10")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This reverts commit 57e4cc8261.
Cmdline override patch was fixed. It's time for reenable
Asrock G10 support.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Tested-by: Hannu Nyman <hannu.nyman@iki.fi> (run-tested for R7800)
900-arm-add-cmdline-override.patch have missplaced entry in
arch/arm/Kconfig file. It causes problem with other cmdline
patches. This patch put Kconfig entry in correct place.
Fixes: 98b86296e6 ("ipq806x: add support for ASRock G10")
Suggested-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Tested-by: Hannu Nyman <hannu.nyman@iki.fi> (run-tested for R7800)
After device support for ASRock G10 was added in [1], several
people reported broken ipq806x devices, with one or several of the
following symptoms:
- Device does not boot
- Sysupgrade does not work
- Serial console is broken
The issues appears to be caused by the introduction of the symbol
CONFIG_CMDLINE_OVERRIDE=y in [1].
This patch disables the corresponding symbol again and marks the
ASRock as BROKEN, as it probably won't work properly without it.
Further references:
https://bugs.openwrt.org/index.php?do=details&task_id=354098b86296e6 (commitcomment-45455875)
[1] 98b86296e6 ("ipq806x: add support for ASRock G10")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit adds support for Qualcomm IPQ8062 SoC.
IPQ8062 is a lower clock variant of IPQ8064.
CPU and NSS clocks:
- CPU: 384 MHz - 1 GHz
- NSS: 110 MHz - 550 MHz
opp and l2 clock values are taken from WG2600HP3 GPL source code [1].
Due to a lack of devices, I didn't test the following features.
- SATA
- NAND flash memory controller
- SD
- USB
- GSBI2, GSBI7
- PCIE2
- GMAC0, GMAC3
Works properly:
- GSBI4 UART
- GSBI5 SPI
- GMAC1, GMAC2
- PCIE0, PCIE1
- MDIO0
Does not work properly:
- CPU SPC
- This can cause a system hang. Same as IPQ8065.
See 2336c2dbb1
[1] https://www.aterm.jp/function/wg2600hp3/appendix/opensource.html
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
The ASRock G10 is a 2.4/5 GHz band 11ac "Gaming" router,
based on Qualcomm IPQ8064.
Specifications:
SoC: Qualcomm IPQ8064
CPU: Dual-Core A15 @ (384 - 1,400 MHz, 2C2T)
DRAM: 512 MiB (~467 MiB available)
NAND: 128 MB (Micron MT29F1G08ABBEAH4)
WLAN0: 4T4R 5 GHz Wlan (QCA9980)
WLAN1: 4T4R 2.4 GHz Wlan (QCA9980)
ETH: 5x 10/100/1000 Mbps Ethernet (QCA8337)
INPUT: Reset Button, WPS 2.4G and WPS 5G Button
LEDS: 1 multicolor status LED
USB: 2x USB 3.0 Type-A
POWER: 12VDC/3A AC Adapter + dedicated Power Switch
UART: Setting is 115200-8-N-1. 1x4 .1" unpopulated header
on the PCB (J6 - very tiny silkscreen next to TX).
Pinout: 1. 3v3 (Square - best skipped!), 2. RX, 3. GND, 4. TX
WARNING: The serial port needs a TTL/RS-232 3.3v level converter!
(Depending on the serial adapter RX and TX might need to
be swapped).
Note about the IR-Remote:
There's a 8-Bit MCU (SONIX SN8F25E21SG) which is controlling the
IR-Remote and is fed by the IR-Photodiode. The SoC can talk to
the device via I2C. The vendor's GPL archive comes with the source
of the interface driver for this as a (character driver), the main
control software is however a blob.
Installation Instructions:
1. Download factory image to disk
2. Apply factory image via stock web-gui
Back to stock:
1. Login to router via ssh
2. run "asrock_g10_back_to_factory" script from /sbin
Notes:
- If something goes wrong durring sysupgrade, router will go back to
factory image.
- Asrock G10 uses partition layout from smem. So partition layout can
be normal or alternate.
- 900-arm-add-cmdline-override.patch was copied from 102-powerpc-add-cmdline-override.patch
from powerpc target.
Knowledge about BOOTCONFIG partition was based on user "jmomo" post from old
OpenWrt forum (Post #50):
https://forum.archive.openwrt.org/viewtopic.php?id=65956&p=2
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[bump to 5.4, add factory image, fix sysupgrade, convert partition
layout to smem, remove ipq-wifi-asrock-g10 and use ART, minor fixes]
Co-Authored-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Tested-by: Lukasz Ostapiuk <palibrzuch@gmail.com>
The WAN port on Netgear D7800 is unable to connect to an ISP when the
link to the modem is running at less than 1GB.
This patch fixes the issue by removing the phy-handle definition
and replacing it with a fixed-link definition
The WAN port is then able to connect to a modem via a link running at 100Mbs or 10Mbs
Fixes: FS#3086
Signed-off-by: Peter Cardoe <peter@cardoe.co.uk>
Manually rebased patches:
ath79/patches-5.4/910-unaligned_access_hacks.patch
bcm27xx/patches-5.4/950-0135-spi-spi-bcm2835-Disable-forced-software-CS.patch
bcm27xx/patches-5.4/950-0414-SQUASH-Fix-spi-driver-compiler-warnings.patch
ipq806x/patches-5.4/093-4-v5.8-ipq806x-PCI-qcom-Use-bulk-clk-api-and-assert-on-error.patch
Removed since could be reverse-applied by quilt and found to be included upstream:
ipq806x/patches-5.4/096-PCI-qcom-Make-sure-PCIe-is-reset-before-init-for-rev.patch
All modifications made by update_kernel.sh
Build system: x86_64
Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
[refresh altered targets after rebase]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Manually rebased patches:
bcm27xx:
patches-5.4/950-0267-xhci-add-quirk-for-host-controllers-that-don-t-updat.patch
bcm53xx:
patches-5.4/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
layerscape:
patches-5.4/802-can-0025-can-flexcan-add-LPSR-mode-support-for-i.MX7D.patch
patches-5.4/808-i2c-0002-MLK-10893-i2c-imx-add-irqf_no_suspend.patch
patches-5.4/820-usb-0016-MLK-16735-usb-host-add-XHCI_CDNS_HOST-flag.patch
Removed since could be reverse-applied by quilt:
mediatek:
patches-5.4/0700-arm-dts-mt7623-add-missing-pause-for-switchport.patch
All modifications made by update_kernel.sh
Build system: x86_64
Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711, x86_64
Run-tested: ipq806x/R7800, x86_64
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
Tested-by: Curtis Deptuck <curtdept@me.com> [x86_64]
Rebase of 802-can-0025-can-flexcan-add-LPSR-mode-support-for-i.MX7D.patch
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Pci is broken when bootm is used instead of the custom bootipq. This
is caused by the lack of reset by the bootloader. Make the driver do
the reset to fix this specific problem.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
The target uses 5.4 as default kernel since 04/2020.
Kernel 4.19 support is not really maintained anymore, and there has
been a lot of changes between 4.19 and 5.4 on this target. Despite,
new devices are typically added for 5.4 only anyway.
Thus, make maintaining of old stuff and reviewing of new stuff
easier by removing support for kernel 4.19.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The vDSO is used to accelerate some syscalls. It should work fine wherever it's
available, so enable it globally for all targets.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Like in the previous patches for ath79 and ramips, this will remove
the "devicename" from LED labels in ipq806x.
The devicename is removed in DTS files and 01_leds, and a migration
script is added.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Seemingly unneeded based on new upstream code so manually deleted:
layerscape:
820-usb-0007-usb-dwc3-gadget-increase-timeout-value-for-send-ep-c.patch
Manually merged:
generic-hack:
251-sound_kconfig.patch
All other modifications made by update_kernel.sh
Build system: x86_64
Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711
Run-tested: ipq806x/R7800, lantiq/Easybox 904 xDSL
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
[add lantiq test report, minor commit message clarification]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This fixes several stylistic and functional errors of the recently
added Edgecore ECW5410:
- fix call in 11-ath10k-caldata
- use hex notation in 11-ath10k-caldata
- remove redundant definitions from DTS that are already in DTSI
- use proper sorting in image/Makefile
- use DEVICE_VENDOR/DEVICE_MODEL instead of DEVICE_TITLE
- use SOC instead of DEVICE_DTS
Fixes: 59f0a0fd83 ("ipq806x: add Edgecore ECW5410 support")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
All modifications made by update_kernel.sh/no manual intervention needed
Run-tested: ipq806x (R7800), ath79 (Archer C7v5), x86/64
No dmesg regressions, everything appears functional
Signed-off-by: John Audia <graysky@archlinux.us>
[add run test from PR]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds support for the Edgecore ECW5410 indoor AP.
Specification:
- SoC: Qualcomm Atheros IPQ8068 ARMv7 2x Cortex A-15
- RAM: 256MB(225 usable) DDR3
- NOR Flash: 16MB SPI NOR
- NAND Flash: 128MB S34MS01G2 Parallel NAND
- Ethernet: 2 x 1G via 2x AR8033 PHY-s connected directly to GMAC2 and GMAC3 via SGMII (802.3af POE IN on eth0)
- USB: 1 x USB 3.0 SuperSpeed
- WLAN: 2x QCA9994 AC Wawe 2 (1x 2GHz bgn, 1x 5GHz acn)
- CC2540 BLE
- UART console on RJ45 next to ethernet ports exposed.
Its Cisco pin compatible, 115200 8n1 baud.
Installation instructions:
Through stock firmware or initramfs.
1.Connect to console
2. Login with root account, if password is unknown then interrupt the boot with f and reset it in failsafe.
3. Transfer factory image
4. Flash the image with ubiformat /dev/mtd1 -y -f <your factory image path>
This will replace the rootfs2 with OpenWrt, if you are currently running from rootfs2 then simply change /dev/mtd1 to /dev/mtd0
Note
Initramfs:
1. Connect to console
2. Transfer the image from TFTP server with tftpboot,
or by using DHCP advertised image with dhcp command.
3. bootm
4. Run ubiformat /dev/mtd1
You need to interrupt the bootloader after rebooting and run:
run altbootcmd
This will switch your active rootfs partition to one you wrote to and boot from it.
So if rootfs1 is active, then it will change it to rootfs2.
This will format the rootfs2 partition, if your active partition is 2 then simply change /dev/mtd1 with /dev/mtd0
If you dont format the partition you will be writing too, then sysupgrade will find existing UBI rootfs and kernel volumes and update those.
This will result in wrong ordering and OpenWrt will panic on boot.
5. Transfer sysupgrade image
6. Flash with sysupgrade -n.
Note that sysupgrade will write the image to rootfs partition that is not currently in use.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
This imports the patch that adds bootargs-append support from IPQ40xx.
This way we can append additional boot arguments from DTS instead of only being able to overwrite them.
This way dual firmware devices can use the rootfs number that bootloader passes to decide from what to boot.
But we still need to append console info and ubi root info.
This is used by Edgecore ECW5410.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
IPQ806x series also has a GSBI1 with UART and I2C peripherals, so lets add the node for it.
Its needed for Edgecore ECW5410 which uses the UART from GSBI1 as second UART for Bluetooth.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Its needed for Edgecore ECW5410 which does not use QCA8337 switch,
but rather 2x AR8033 PHY-s directly connected to GMAC-s.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Manually merged:
hack-5.4
230-openwrt_lzma_options.patch
bcm27xx
950-0283-hid-usb-Add-device-quirks-for-Freeway-Airmouse-T3-an.patch
x86
011-tune_lzma_options.patch
Remove upstreamed patches in collaboration with Ansuel Smith:
ipq806x
093-1-v5.8-ipq806x-PCI-qcom-Add-missing-ipq806x-clocks-in-PCIe-driver.patch
093-2-v5.8-ipq806x-PCI-qcom-Change-duplicate-PCI-reset-to-phy-reset.patch
093-3-v5.8-ipq806x-PCI-qcom-Add-missing-reset-for-ipq806x.patch
All other modifications made by update_kernel.sh
Build-tested: bcm27xx/bcm2708, ipq806x, x86/64
Run-tested: ipq806x (R7800), x86/64
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
[update commit message/tested]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Changes:
- Update patches
- Update dts with new binding
Tx term offset dropped and replaced with a new compatible
Removed:
- 0071-5-PCI-qcom-Programming-the-PCIE-iATU-for-IPQ806x
Pci init does the same exact thing (was needed in older kernel version)
- 0071-7-pcie-Set-PCIE-MRRS-and-MPS-to-256B
Rejected upstream, can't find any reason to have this. No regression with
testing it on R7800.
Tested on R7800 (ipq8065), R7500 v2 ("ipq8064-v2")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Tested-by: Paul Blazejowski <paulb@blazebox.homeip.net> [R7800]
[rebase and refresh]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In order to support SAE/WPA3-Personal in default images. Replace almost
all occurencies of wpad-basic and wpad-mini with wpad-basic-wolfssl for
consistency. Keep out ar71xx from the list as it won't be in the next
release and would only make backports harder.
Build-tested (build-bot settings):
ath79: generic, ramips: mt7620/mt76x8/rt305x, lantiq: xrx200/xway,
sunxi: a53
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[rebase, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The moves a few additional common nodes to the common DTSI files
for qcom-ipq8064-v2.0 and qcom-ipq8065 devices.
Remove a few redundant definitions on the way.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This driver is only used by ipq806x SoCs. Move it there and drop
dependency from ipq40xx since it's not used anywere.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[rebase on changes to previous patches]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Paul Blazejowski <paulb@blazebox.homeip.net> [R7800]
- Replace nvmem qcom patch with upstream version
- Update compatible
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[refresh patches, minor commit message rewording]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Paul Blazejowski <paulb@blazebox.homeip.net> [R7800]
- Replace dwc3 phy patch with upstream version
- Rework the dts to use the upstream bindings
- Update changed config flags
- Rename module to reflect config name
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[fix qcom,tx-deamp_3_5db typo, refresh patches, rename kmod]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Paul Blazejowski <paulb@blazebox.homeip.net> [R7800]
Replace all the custom patches with the backported upstream version
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[refresh patches]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This uses upstream qcom-ipq8064-v1.0.dtsi and modifies it by patches
instead of keeping a local version. As a consequence:
- we use a part of the shared definitions there and update device
DTS files accordingly
- we move additional stuff from our local v1.0.dtsi to the patch
- we drop partitions, LEDs and keys from the file as we will
implement them differently anyway
Like with the previous patch, this follows the idea that a diff
from upstream might be easier to handle than a big file of our
own with different distribution pattern of properties.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Though a qcom-ipq8064.dtsi file exists upstream, we still do overwrite
it with a full version of our own in the ipq806x target. About half of
the contents of our file are upstream content, the other half are local
improvements.
To prevent us from having a lot of code maintained twice in parallel,
this adjusts the target to use the upstream qcom-ipq8064.dtsi. Our
local changes are arranged into three patches, the first pulling a
commit from upstream, the second doing a few small adjustments, and
the third adding all additional stuff.
This should get us the best of both worlds.
The property "ports-implemented" on sata@29000000 is moved to
2nd-level DTSI files as kernel defines it there as well.
While at, rename 080-ARM-dts-qcom-add-gpio-ranges-property.patch to
include the kernel version where it's added upstream.
Even though this might look more complicated in the first place,
the aim is to bring our files closer to upstream, so we can benefit
from changes directly and vice-versa. After all, this drop about
650 lines just copied from the upstream DTSI file.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Having looked at this again, it appears that only gsbi2_serial
is actually enabled for this device, so the entry in the broken
aliases node was correct.
Therefore, this needs to set its own serial0 instead of inheriting
"serial0 = &gsbi4_serial;" from DTSI. Do this with the correctly
named aliases node now.
Fixes: c83f7b6d21 ("ipq806x: fix aliases node name for Qualcomm
IPQ8064/DB149")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Kernel uses the label gsbiX_serial, so let's adjust our labels to
this naming scheme.
This is cosmetic, and actually only already existing gsbi4_serial
has been used at all.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This device uses a node incorrectly named "alias" instead of
"aliases" since it was introduced.
Remove it without replacement, as the definitions in it don't
seem to be required anyway:
The serial0 definition has never been effective anyway and this
would be the only device deviating from the common setting
"serial0 = &gsbi4_serial;" for ipq8064. (So, maybe the wrong
node prevented us from finding out about the wrong serial
definition?)
The mdio-gpio0 alias was supposed to be removed in d2a2eb7e48
anyway, the redundant definition in the alias node was just
overlooked back then.
Fixes: 0fd202f3e5 ("ipq806x: add db149 dts files")
Fixes: d2a2eb7e48 ("ipq806x: replace caf nss-gmac driver by upstream stmmac")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
At this moment Linksys EA8500 uses only eth0.
This patch change switch registers, which allow to use eth1 as lan
and eth0 as wan. The method work with similar Linksys EA7500V1
and it work with EA8500.
Suggested-by: Sungbo Eo <mans0n@gorani.run>
Tested-by: Brian Onn <brian.a.onn@gmail.com>
Tested-by: Adrian Panella <ianchi74@outlook.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Commit e53ec043ba ("kirkwood: move usb support to modules") has moved
this config symbol into generic configs, so it could be removed from
other configs.
Suggested-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Gives users a third option to augment ondemand and performance. Kernel
docs[1] explain differences and this PR empowers users w/ the choice to
select between the older ondemand and newer and more simplistic schedutil
should they wish to use one that is not the performance governor.
1. Documentation/admin-guide/pm/cpufreq.rst
Signed-off-by: John Audia <graysky@archlinux.us>
[fixed From: to match SoB:]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This patch adds support for the Linksys EA7500 V1 router.
Specification:
- CPU: Qualcomm IPQ8064
- RAM: 256MB
- Flash: NAND 128MB
- WiFi: QCA9982 an+ac + QCA9983 bgn
- Ethernet: 5 GBE Ports (WAN+ 4xLAN) (QCA8337)
- USB: 1x USB 3.0 1x USB2.0
- Serial console: RJ-45 115200 8n1 (1V8 Voltage level)
- 2 Buttons
- 1 LED
Known issues:
- Some devices won't flash via web gui
Installation:
- Newer stock images doesn't allow to install custom firmware.
- Please downgrade software to 1.1.2 version. Official firmware:
https://downloads.linksys.com/downloads/firmware/FW_EA7500_1.1.2.172843_prod.gpg.img
- Do it two times to downgrade all stored images.
- Apply factory image via web-gui.
Serial + TFTP method:
- downgrade to 1.1.2 two times
- connect ehternet and serial cable
- set ip address of tftp server to 192.168.1.254
- put openwrt factory image to tftp folder and rename it to macan.bin
- stop device while booting in u-boot
- run command: "run flashimg"
- run command: "setenv boot_part 1"
- run command "saveenv"
- reset
Back to stock:
- Please use old non-gpg image like this 1.1.2:
https://downloads.linksys.com/downloads/firmware/FW_EA7500_1.1.2.172843_prod.img
- ssh to router and copy image to tmp
- use sysupgrade -n -F
Tested by github users: @jack338c and @grzesiczek1
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[removed i2c4_pins, mdio0_pins, nand_pins, rgmii2_pins from DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
All device DTS files in the target set the serial0 property to the
same value (*). So, let's move the definitions to the DTSI files.
That's also where the kernel defines it (qcom-ipq8064-v1.0.dtsi).
* The only exception is ipq8064-db149, which defines
"serial0 = &uart2;", but inside a block called "alias" instead of
"aliases". It must be assumed that this is broken anyway, so we
don't touch it here.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
All device DTS files in the target set the stdout-path to the same
value. So, let's move the definitions to the DTSI files.
That's also where the kernel defines it (qcom-ipq8064-v1.0.dtsi).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
So far, the DTSI files on ipq806x had a linear inheritance:
qcom-ipq8064.dtsi
v
qcom-ipq8064-v1.0.dtsi
v
qcom-ipq8064-v2.0.dtsi
v
qcom-ipq8065.dtsi
This poses problems when one wants to set something that is specific
to an architecture closer to the top of the tree.
In this patch, we remove the chain-like inheritance and have all
other files derived from qcom-ipq8064.dtsi (changing this name to
something more generic is not possible due to upstream use).
The removal of inheritance will require a few entries to be copied
from qcom-ipq8064-v2.0.dtsi to qcom-ipq8065.dtsi. However, it also
opens an opportunity for some clean-up:
- Many definitions can be improved by just using the innermost labels.
- Instead of disabling the CPU_SPC node for ipq8065, it is now off by
default and enabled where needed.
- Instead of patching phy-tx0-term-offset into qcom-ipq8064.dtsi and
then having it changed for qcom-ipq8064-v2.0/qcom-ipq8065, just have
the appropriate settings done in the lower DTSI files directly.
- For the opp_table0 adjustments for ipq8065, just redefine what's
changed, but don't add all the untouched properties again.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
As almost same pinmux nodes are repeated in each device dts,
let's define them once in the ipq8064 dtsi and remove the rest.
* uart0_pins : Did not touch.
* i2c4_pins : This node seems to be not used at all in dts.
Added the most common form in the dtsi. Did not touch rpm_pins.
* spi_pins : The common mux node is already present in the dtsi.
Removed the duplicate nodes from dts.
* nand_pins : Moved the entire node.
* mdio0_pins : Moved the common mux node.
* rgmii2_pins: Moved the common mux node. "pins" property is overrided in ap161.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Fixes:
- CVE-2020-10757
The "mtd: rawnand: Pass a nand_chip object to nand_release()" commit was
backported which needed some adaptations to other code.
Run tested: ath79
Build tested: ath79
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Based on "make kernel_menuconfig CONFIG_TARGET=generic" and 5.4.49
CONFIG_LEDS_TRIGGER_DISK has been removed by the refresh and added
back manually in order to not revert f93fcf8923 ("ipq806x: enable
disk-activity LED trigger").
Signed-off-by: John Audia <graysky@archlinux.us>
[extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The Device/Default definition sets a default IMAGE/sysupgrade.bin,
but does not enable it by setting IMAGES. This is not consistent,
and has led to IMAGES being defined at various other places in the
file.
Thus, this patch consolidates the default value for IMAGES by putting
it in Device/Default. Since it's still overwritten where necessary,
this patch is cosmetic.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This drops the shebang from all target files for /lib and
/etc/uci-defaults folders, as these are sourced and the shebang
is useless.
While at it, fix the executable flag on a few of these files.
This does not touch ar71xx, as this target is just used for
backporting now and applying cosmetic changes would just complicate
things.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Enable the disk-activity LED trigger for ipq806x, since this SoC has an
onboard SATA controller.
Signed-off-by: Thomas Albers <thomas.gameiro@googlemail.com>
[split into separate commit]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Between 4.19 and 5.4, the kernel moved the partition parsers into
the parsers subdirectory. This led to some necessary rebasing of
our local patches for parsers, which partially has been performed
without caring about where the code was inserted.
This commit tries to adjust our local patches so that parsers are
inserted at the "proper" positions with respect to alphabetic sorting
(if possible). Thus, the commit is cosmetic.
While this might look useless now, it will make life easier when
adding other parsers in the future or for rebasing on kernel changes.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ipq806x has been tested for a lot and lots of people reported good results.
Switch the main kernel to 5.4 following the other targets.
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ipq8065, NBG6817]
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
This target has been on kernel 4.19 for several months [1] and
already uses kernel 5.4 as testing kernel. Therefore, it should
not be necessary to keep support for kernel 4.14 as well.
[1] 2a82e0e1ca ("ipq806x: switch to 4.19 kernel version")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ipq8065/nbg6817]
Place DEVICE_VARS assignments at the top of the file or above Device/Default
to make them easier to find.
For ramips, remove redundant values already present in parent file.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This new symbol popped up in few places. Disable it in generic config.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[fixed merge conflict in generic/config-5.4]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
There is no such role as target maintainer anymore, one should always
send corresponding changes for the review and anyone from the commiters
is allowed to merge them or eventually use the hand break and NACK them.
Lets make it clear, that it is solely a community doing the maintenance
tasks.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Piotr Dymacz <pepe2k@gmail.com>
WG2600HP has its WLAN MAC addresses at PRODUCTDATA 0xc and 0x12, so
use them both directly.
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
[commit title/message clarification]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The default case will catch anything left, there is no need to
explicitly add any device to it.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Currently kmod-ata-* will not get into images unless kmod-ata-core is added to
DEVICE_PACKAGES as well. By changing the dependencies from "depends on" to
"select", we do not have the issue anymore.
Furthermore, we can remove most occurrences of the package from DEVICE_PACKAGES
and similar variables, as it is now pulled by dependent modules such as:
- kmod-ata-ahci
- kmod-ata-ahci-mtk
- kmod-ata-sunxi
While at it, use AddDepends/ata for kmod-ata-pdc202xx-old.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Add 5.4 kernel version as a new testing kernel option.
Ref: https://github.com/openwrt/openwrt/pull/2793
Tested-by: Hannu Nyman <hannu.nyman@iki.fi> [ipq8065, R7800]
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ipq8065, NBG6817]
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[added Tested-by tags]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Due to changes in syscon driver, the phy dwc3 driver
needs to use device_node_to_regmap since it has to skip
the new introduced clk check. This fix broken usb3 on this
target.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
As mdio0 is used in every dts move it to general ipq8064
dts and use label to set device specific definition.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Currently the watchdog timer is broken as it tries to
get an interrupt to setup pretimeout. Since our platform
have a different type of interrupt disable it and use
legacy watchdog probe.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
This was created by Chunkeey some time ago. Since mdio driver
works or doesn't work and since this was tested by me for 1 year,
include it to remove the use of the generic bitbang gpio driver for
switch driver.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Rework tsens driver.
Since in the new kernel 5.4 init common do more than it
should, inizialize the kernel memory directly in the driver and
drop use of this function. Rework all the patch with the new
variable names.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Rework l2 scaling patch to fix some compile warning
and to imporve the caling timings by removing call to unnecessary
function.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Since this dtsi now have wrong definition in the upstream version,
include it to overwrite and remove any problem.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Refactor l2 freq scaling patch to support voltage
scaling and add support to base cache scaling on
cpu freq scaling. Update the dtsi files with the new
definition used in the new code.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
It's wrong set the mux to bias-disable. The best way to
do this is by creating a separate group and disable the
specific pins.
By documentation, any subgroup with no bias definition
is ignored so the mux definition is useless.
Rework the definition by sremoving the mux subgroup and
set the remaining subgroup with the mux function and
drive-strength
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
The opp_notifier introduced with patch 0054-Handle-OPP-voltage adjust
for some reason missed the actual registration in the opp struct,
resulting in never being registred.
This was present in kernel 4.9 patchset but dropped in the transition
to 4.14. Reintroduce this and fix patch 0055 about L2 cache scaling.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
This patch uses the SOC variable to calculate DTS names automatically
based on the SOC and the device definition node name.
This reduces redundancy and (by having to choose DTS name
appropriately) will unify the naming of a device in different places
(image/Makefile, DTS name, compatible, image name). This is supposed
to make life easier for developers and reviewers.
Since the kernel uses a "soc-device.dts" scheme for this target, we
use this for the derivation of DEVICE_DTS, too, leaving the DTS names
unchanged for this target.
Note that for some devices the kernel itself uses inconsistent names
(DTS naming scheme vs. compatible), leaving us with a manual overwrite
of DEVICE_DTS for those cases.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
We have only 11 sensors on ipq806x. Fix the reg property
to load the right amount of data instead of the entire
space.
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [nbg6817/ipq8065]
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Tsense driver for ipq806x have various problem.
- Emit wrong error. On probing of this driver, nvmem driver can be
not ready and this cause a EDEFER error. Actually this is not an
error as the kernel will retry to probe the driver after the
nvmem driver is loaded.
- Use uninitialized value on trigger of critical temp
- Doesn't free allocated memory
Because of this, rework the driver and improve it by removing extra
load of data.
Change the logic of loading data. Use the backup calib data only
when the calib data is not present. As the calibration is only
needed to set the temp offset, we don't really need to read
both calib data and set the offset based only on the backup one.
Also change how the notifier function work. At times when we
output the trigger message, we already have read the temp so
remove the extra read and the wrong uninitialized data that
probably caused a kernel panic for null pointer exception.
(Think we never experience this bug because the router
never reached that temp ever... So just lucky)
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [nbg6817/ipq8065]
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
The config name for cpufreq driver has changed.
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [nbg6817/ipq8065]
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
The new driver use opp table to register frequency.
Drop psv bindings as they are not used anymore.
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [nbg6817/ipq8065]
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
The new driver use opp table to register frequency.
Drop psv bindings as they are not used anymore.
Adds speedbin definition for nvmem driver
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [nbg6817/ipq8065]
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
This patch has been proposed but never actually merged to
mainline. It was accepted but never re proposed by the
creator.
Rework it, fix kernel panic cause by double kfree.
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [nbg6817/ipq8065]
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Backport patch applied to qcom-cpufreq-kryo
driver as krait cpu will base on this driver.
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [nbg6817/ipq8065]
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Drop old cpufreq as now we have new driver that
can use normal kernel opp definition
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [nbg6817/ipq8065]
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Rework 0052-PM-OPP-Update-the-voltage-tolerance-when-adjusting-t
to reflect changes upstream.
- Skip unnecessary allocation of buffer to set u_volt
- Change opp u_volt directly
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [nbg6817/ipq8065]
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Update 0049-PM-OPP-Support-adjusting-OPP-voltages-at-runtime with
upstream version.
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [nbg6817/ipq8065]
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
It has been notice a buf in L2 cache scaling where the scaling is not
done proprely if the frequency is set to the initial state before
the new frequency.
From: https://patchwork.kernel.org/patch/10565443/
* The clocks are set to aux clock rate first to make sure the
* secondary mux is not sourcing off of QSB. The rate is then set to
* two different rates to force a HFPLL reinit under all
* circumstances.
In the initial stage of boot to force a new frequency to apply, is
needed to first set the frequency back to the lowest one (aux_rate)
and then to the target one. This force and make sure the controller
actually switch the frequency to the right one. Apply the same
mechanism to L2 frequency scaling. Before scaling to the target
frequency, first set the frequency to the aux_rate to force the
transition, then scale it to the target frequency. Doing the wrong way
can produce unexpected results and could lock the scaling mechanism
until a full reboot is done (Causing a full reset by the krait-cc driver)
From: https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/commit/?id=77612720a2362230af726baa4149c40ec7a7fb05
When the Hfplls are reprogrammed during the rate change,
the primary muxes which are sourced from the same hfpll
for higher frequencies, needs to be switched to the 'safe
secondary mux' as the parent for that small window. This
is done by registering a clk notifier for the muxes and
switching to the safe parent in the PRE_RATE_CHANGE notifier
and back to the original parent in the POST_RATE_CHANGE notifier.
This should apply also to L2 scaling... as we can't relly use
the notifier, we manually do this on L2 scaling.
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [nbg6817/ipq8065]
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Deactivate CONFIG_SFP for kernel 4.19 in the generic configuration.
The CONFIG_SFP configuration option was not set to anything in the
ath79 build for me, set it to deactivated by default.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It has been used by several people for some time already and feedback
has been mostly positive.
Ref: https://github.com/openwrt/openwrt/pull/2472
Tested-by: Hannu Nyman <hannu.nyman@iki.fi> [ipq8065, R7800]
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ipq8065, NBG6817]
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[separate commit, commit subject and description facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
- Use new dwc3-qcom usb driver.
- Drop dwc3-of-simple as we have a dedicated driver now.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[split into separate commit, commit subject facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Voltage tolerance is accounted per core, not per cpu, so add
missing DT entry.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Added patch:
- 063-3 Fix tsense shared memory problem
Recent changes in ioremap_resource function are causing fails for the
memory areas which are already mapped. This changes are causing tsense
driver failures during initialization:
qcom-tsens 900000.thermal-sensor: tsens init failed
So this patch uses simple ioremap in order to use this shared memory
space.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[commit subject and desciption facelitf]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Improve rediability of gpio mdio list. No functional change.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[proper authorship of the patch]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
From documentation
https://www.kernel.org/doc/Documentation/devicetree/bindings/chosen.txt
should be just stdout-path
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[proper authorship of the patch]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Reorganize dts to use tags from ipq8064 dtsi
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
There is warning with "property has invalid length (4 bytes)"
related to nand definition. Set size-cells to zero to fix this.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Add missing watchdog to list of compatible timers
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Add some tags for nand and sata structure to easily
reference them in other dts.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Increase drive-strength from
https://lore.kernel.org/patchwork/patch/626885/
2mA drive strength is not enough when we connect multiple i2c devices
on the bus with different pull up resistors.
This issue was detected when multiple i2c devices
connected on the other side of level shifters on Linaro sensor board.
Maxing up to 16mA made i2c much stable.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Spc is disabled in ipq8065 board as it does cause cpu lockup
(probably caused by wrong register being set)
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Use new usb3 implementation and refresh dts to the new dwc3 structure
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[proper authorship of the patch]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
- ipq8064 compatible was missing from nbg6817.
- Rename ap148 with a better descriptive name.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[proper authorship of the patch]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
DT spec require okay instead of ok in dts files
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reworked:
- 0034 patchset update
Added:
- 080 Add support for pinctrl-msm framework
Removed:
- 0074-ipq806x-usb-Control-USB-master-reset.patch
(we now have a dedicated driver for qcom usb)
- 0047-mtd-nand-Create-a-BBT-flag-to-access-bad-block-marke
(merged upstream)
- 310-msm-adhoc-bus-support
(it looks like it was never actually used in any dts)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[commit subject and description facelift, SoB fix]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
These changes are needed in order to migrate old kernel 4.14 config to
the upcoming kernel version 4.19. Also add missing configuration
options that comes up with this SoC.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[line wrap long commit description, add 4.19 to subject, soc->SoC]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This copies files from files-4.14 to files-4.19 directory in order to
get clear diffs for any changes done from now on.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[added missing commit description, refreshed ea8500 and wpq864 DTS]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
There is a problem with the EA8500, the switch will not work after soft
reboot, the only way to get it working again is to power cycle it
manually.
There are probably several issues in the play, it's quite hard to fix it
without having access to the actual device, so I don't see any other
option now, then revert the offending commit.
Ref: PR#2047
Fixes: FS#2168 ("Switch no longer work after restart on Linksys EA8500")
Reported-by: Adam <424778940z@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
With this commit, the WAN LED is triggered by the switch port state
instead of the eth0 netdev.
Otherwise, the LED is always illuminated, regardless of the WAN port
link state.
Signed-off-by: David Bauer <mail@david-bauer.net>
This patch fixes what seems to be a simple copy & paste
error with the unit-address of the BOOTCONFIG partition.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
While all ath10k eeproms have a checksum field, so far two
functions for patching ath10k MAC address have been present (and
been used).
This merges code to provide a single function ath10k_patch_mac
in caldata.sh, having its name in accordance with ath9k functions.
By doing so, correct MAC patching for current and future ath10k
devices should be ensured.
This patch adds checksum adjustments for several targets on
ath79 and lantiq.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This unifies MAC address patch functions and moves them to a
common script. While those were implemented differently for
different targets, they all seem to do the same. The number of
different variants is significantly reduced by this patch.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This moves the almost identical calibration data extraction
functions present multiple times in several targets to a single
library file /lib/functions/caldata.sh.
Functions are renamed with more generic names to merge different
variants that only differ in their names.
Most of the targets used find_mtd_chardev, while some used
find_mtd_part inside the extraction code. To merge them, the more
abundant version with find_mtd_chardev is used in the common code.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[rebase on latest master; add mpc85xx]
Signed-off-by: David Bauer <mail@david-bauer.net>
The xor() function is defined in each of the caldata extraction
scripts for several targets. Move it to functions.sh to reduce
duplicate code.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This removes _all_ occurrences of kmod-usb-core from
DEVICE_PACKAGES and similar variables.
This package is pulled as dependency by one of the following
packages in any case:
- kmod-usb-chipidea
- kmod-usb-dwc2
- kmod-usb-ledtrig-usbport
- kmod-usb-ohci
- kmod-usb2
- kmod-usb2-pci
- kmod-usb3
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[remove kmod-usb-core from EnGenius ESR600]
Signed-off-by: David Bauer <mail@david-bauer.net>
The following symbols, selected by the qce driver were removed:
CONFIG_CRYPTO_CBC
CONFIG_CRYPTO_CTR
CONFIG_CRYPTO_DES
CONFIG_CRYPTO_DEV_QCE
CONFIG_CRYPTO_ECB
CONFIG_CRYPTO_NULL
CONFIG_CRYPTO_SEQIV
CONFIG_CRYPTO_XTS
CONFIG_CRYPTO_GF128MUL was removed as well, since it is only needed by
some cipher modes (LRW, GCM), none of which are selected, and it is
packaged as a module.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
It's a variable set by procd that should replace hardcoded
/tmp/sysupgrade.tgz.
This change requires the most recent procd with the commit 0f3c136
("sysupgrade: set UPGRADE_BACKUP env variable").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
$CONF_TAR shouldn't be assumed to always point to the sysupgrade.tgz.
This change makes code more generic and allows refactoring $CONF_TAR.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
1) Add BACKUP_FILE and use it when copying an archive to be restored
after sysupgrade (on the next preinit).
2) Use CONF_TAR for copying backup prepared by the /sbin/sysupgrade
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Both targets miss a subtarget causing an image naming style which is
different from other all othe targets, even tho it already uses
`x/generic/` as subfolder as if the subtarget would exist.
This commit adds the Generic subtarget resulting in consistent naming.
~/src/openwrt/openwrt/bin/targets/ipq806x/generic$ ls
openwrt-ipq806x-generic-netgear_d7800-initramfs-uImage
openwrt-ipq806x-generic-netgear-d7800.manifest
openwrt-ipq806x-generic-netgear_d7800-squashfs-factory.img
openwrt-ipq806x-generic-netgear_d7800-squashfs-sysupgrade.bin
CC: John Crispin <john@phrozen.org>
Signed-off-by: Paul Spooren <mail@aparcar.org>
This commit made the following changes to sync all bootcount scripts:
1. use boot() instead of start()
This script only needs to be executed once when boot is complete.
use boot() to make this explicit.
2. drop sourcing of /lib/functions.sh
This is aready done in /etc/rc.common.
3. ramips: replace board name checking with a case
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This changes size and offset set for WiFi caldata extraction and
MAC address adjustment to hexadecimal notation.
This will be much clearer for the reader when numbers are big, and
will also match the style used for mtd-cal-data in DTS files.
Since dd cannot deal with hexadecimal notation, one has to convert
back to decimal by simple $(($hexnum)).
Acked-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This changes the offsets for the MAC address location in
mtd_get_mac_binary* and mtd_get_mac_text to hexadecimal notation.
This will be much clearer for the reader when numbers are big, and
will also match the style used for mtd-mac-address in DTS files.
(e.g. 0x1006 and 0x5006 are much more useful than 4102 and 20486)
Acked-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
1) nand_do_upgrade() is always called by a target code
2) nand_do_upgrade() starts with calling platform_nand_pre_upgrade()
It means there is no need for the platform_nand_pre_upgrade() callback
at all. All code that was present there could bo moved & simplly called
by a target right before the nand_do_upgrade().
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Consistently handle boot-count reset and upgrade across
ipq40xx, ipq806x, kirkwood, mvebu
Dual-firmware devices often utilize a specific MTD partition
to record the number of times the boot loader has initiated boot.
Most of these devices are NAND, typically with a 2k erase size.
When this code was ported to the ipq40xx platform, the device in hand
used NOR for this partition, with a 16-byte "record" size. As the
implementation of `mtd resetbc` is by-platform, the hard-coded nature
of this change prevented proper operation of a NAND-based device.
* Unified the "NOR" variant with the rest of the Linksys variants
* Added logging to indicate success and failure
* Provided a meaningful return value for scripting
* "Protected" the use of `mtd resetbc` in start-up scripts so that
failure does not end the boot sequence
* Moved Linksys-specific actions into common `/etc/init.d/bootcount`
For upgrade, these devices need to determine which partition to flash,
as well as set certain U-Boot envirnment variables to change the next
boot to the newly flashed version.
* Moved upgrade-related environment changes out of bootcount
* Combined multiple flashes of environment into single one
* Current-partition detection now handles absence of `boot_part`
Runtime-tested: Linksys EA8300
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[checkpatch.pl fixes, traded split strings for 80+ chars per line]
This patch increases available space from 20MB to 86MB.
Netgrear OEM firmware contains a 'netgear' partition followed 'ubi',
which can be used in openwrt for larger ubi space. (similar to
Netgear R7800).
original author (notmyrealhandle) tested this on R7500v2 and point that
OEM firmware can auto rebuild this partition (if used by openwrt).
Author: notmyrealhandle<22336358+notmyrealhandle@users.noreply.github.com>
Signed-off-by: Wang Xin-yu (王昕宇) <comicfans44@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [minor touch-ups]
NEC WG2600HP uses port1 on QCA8337 as a WAN port, so "0x2" should
be used as a portmask instead of "0x1e" for "WAN" LED configuration.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
(original text here: https://patchwork.kernel.org/patch/8686761/)
On some SOCs PORTS_IMPL register value is never programmed by the BIOS
and left at zero value. Which means that no sata ports are avaiable for
software. AHCI driver used to cope up with this by fabricating the
port_map if the PORTS_IMPL register is read zero, but recent patch
broke this workaround as zero value was valid for nvme disks.
This patch adds ports-implemented dt bindings as workaround for this issue
in a way that DT can dictate the port_map incase where the SOCs does not
program it already.
This patch is equal to commits:
67f8425d0ee1 ("ipq8064: dts: force AP148 SATA port mapping")
2e7a2c91019c ("ARM: dts: qcom: Move common nodes to ipq8064-v.1.0.dtsi")
in the upstream linux kernel.
Signed-off-by: Roman Glova <roman_glova@epam.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[added upstream commits, reorg' commit message]
Buffalo WXR-2533DHP is a 2.4/5 GHz band 11ac router, based on Qualcomm
IPQ8064.
The U-Boot on WXR-2533DHP employs a complicated dual firmware
protection scheme against corruptions of the kernel and rootfs
images. See the notes in buffalo.sh for details.
specifications:
- Qualcomm IPQ8064 (384 - 1,400 MHz, 2C2T)
- 512 MB of RAM (DDR3)
- 256 MB of Flash (NAND)
- 4T4R 2.4/5 GHz Wlan (QCA9980)
- 5x 10/100/1000 Mbps Ethernet
- 10x LEDs, 8x keys (6x buttons, 2x slide-switches)
- 2x USB 3.0 Type-A
- 12VDC/4A AC Adapter
- UART through-hole on PCB
- J3: Vcc, GND, TX, RX from USB port side
- 115200n8
Boot instructions for the initramfs image:
1. Prepare the TFTP server with the initramfs image renamed to
"wxr2300dhp-initramfs.uImage" and IP address "192.168.11.10".
2. Press the "AOSS" button while powering on the WXR-2533DHP.
3. Wait until the "Wireless" LED flashes before releasing the AOSS button.
The WXR-2533DHP will grab the image from TFTP server and will boot it.
Flashing instructions:
To persistently write the firmware, flash an openwrt sysupgrade image
from inside the initramfs, for example transfer
via `scp <sysupgrade> root@192.168.1.1:/tmp` and flash on the device
with `sysupgrade -n /tmp/<sysupgrade>`. Then wait ~120 seconds to
let it finish the flashing process.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded message]
This commits adds the "ramdisk" feature to ipq806x target. The
main driving force behind this decision is to facilitate the
installation of OpenWrt on some locked IPQ806x devices.
Examples:
- NEC Aterm WG2600HP
The U-Boot on WG2600HP is protected with a password which prevents
users from gaining access to the u-boot prompt in order to install
the images from there.
Therefore, on this device, installing OpenWrt by the user involves
changing the bootcmd as follows so that WG2600HP downloads and
executes initramfs image from TFTP server.
ex.:
bootcmd="ping ${serverip} && tftpboot 0x44000000 wg2600hp-initramfs.bin; bootipq"
- Buffalo WXR-2533DHP
The U-Boot on WXR-2533DHP has built-in firmware recovery mode.
It's activated by holding the "AOSS" button during boot. This
will trigger the device to download the firmware from an TFTP
server and booting from it. By using this, the user can the
install OpenWrt firmware without having access to the UART
console.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded commit]
Since commit 8e9a59a6b9 (build: add
mkrasimage) a proper factory image can be provided for the ZyXEL
NBG6817, which can be flashed from the OEM firmware or used for
tftp based push-button recovery, therefore the previously used
partition images for mmcblk0p5-rootfs.bin and mmcblk0p4-kernel.bin
are no longer required (and using them properly has always been
slightly difficult and risky) and can now be dropped from the image
generation code.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Ben Greear reported in his patch:
|Subject: netgear r7800: Fix mac address of radios.
|
|Reloading the driver causes the phyX to change, and that
|caused the MAC address to change.
This is because all ODM/OEMs except QCA bothered to write
the correct MAC address for the ath10k wifi into the
calibration data.
This patch copies over the MAC patching helper functions from ipq40xx's
target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
file and converts all the devices to patch the correct MACs into the
extracted calibration data before it gets sent to the driver, which sets
up the device with the correct MAC address. It also removes the entries
in the 10_fix_wifi_mac file as they have served their purpose for good.
Please note the C2600: There is conflicting information on what
the offset for the second wifi is supposed to be. This patch uses
what was specified in 10_fix_wifi_mac.
According to Ben Greear this method is save to use with the
stock firmware too. As he explained that the stock firmware
messes up rx-bssid mask calculation when the MAC is changed
after the first vif is created.
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
I wanted to add status LEDs support to my imx6 based board and have found out,
that I could use diag.sh script found in ramips platform, which seems to be
also shared in a few other platforms:
4801276bc2078c5bcf03003c831e3b0a target/linux/ramips/base-files/etc/diag.sh
4801276bc2078c5bcf03003c831e3b0a target/linux/ipq40xx/base-files/etc/diag.sh
4801276bc2078c5bcf03003c831e3b0a target/linux/ath79/base-files/etc/diag.sh
And @chunkeey suggested to me, that I can also add lantiq, ipq806x and
apm821xx to the list of platforms which could share this generic
diag.sh.
I've extended the base diag.sh in a way, that if it detects any of the
DTS LED aliases, then it would use the generic DTS set_led_state code.
The code in platform's diag.sh has moved to base-files package in this
commit:
base-files: diag.sh: Make it more generic towards DTS so it could be reused
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Tested-by: Christian Lamparter <chunkeey@gmail.com> (apm821xx and ipq40xx)
This change enables support to select phy4 in RGMII mode and
enables RGMII TX/RX clock internal delays.
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
Specification:
- SoC: Qualcomm Atheros IPQ8064 ARM-v7 Dual Core SMP CPU
- RAM: 512MB DDR3 System Memory
- NOR Flash: 32MB SPI NOR
- NAND Flash: 256MB NAND
- Ethernet: 5 x 1G via QCA8337N
- USB: 2 x USB 3.0 SuperSpeed
- PCIe: 3x Mini PCIe 2.0 Slots
Three PCIE2.0 connectors can connect two or three radio cards
such as the CUS260 for 2.4 GHz WLAN and the CUS239 for 802.11ac WLAN
How to flash via u-boot console:
tftpboot 0x44000000 openwrt-ipq806x-qcom_ipq8064-ap161-squashfs-nand-factory.bin
nand erase 0x1340000 0x4000000
nand write 0x44000000 0x1340000 $filesize
setenv bootargs ‘console=ttyMSM0,115200 ubi.mtd=ubi root=/dev/ubiblock0_1’
saveenv
bootm
Further upgrades via sysupgrade.
Tested on IPQ8064 AP161 Board:
1) NAND boot
2) Tested USB and PCIe interfaces
3) WDOG test
4) cpu frequency scaling
5) ethernet, 2G and 5G WiFi
6) ubi sysupgrade
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
This way the radio (phy) name can be the same through module reloads.
To set the desired name:
uci set wireless.@wifi-device[0].phyname=wiphy0
I guess this only works on ipq6086 boards as I could not find a more
generic place to put this. Maybe someone can improve it.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Refreshed all patches.
Altered patches:
- 666-Add-support-for-MAP-E-FMRs-mesh-mode.patch
New symbol for arm targets:
- HARDEN_BRANCH_PREDICTOR
Compile-tested on: ar71xx, cns3xxx, imx6
Runtime-tested on: ar71xx, cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Add out of the box support for 802.11r and 802.11w to all targets not
suffering from small flash.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Mathias did all the heavy lifting on this, but I'm the one who should
get shouted at for committing.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This follows a similar upstream patch by Rob Herring:
|commit 78e5dfea84dc15d69940831b3981b3014d17222e
|Author: Rob Herring <robh@kernel.org>
|Date: Wed Feb 28 16:44:06 2018 -0600
| powerpc: dts: replace 'linux,stdout-path' with 'stdout-path'
|
| 'linux,stdout-path' has been deprecated for some time in favor of
| 'stdout-path'. Now dtc will warn on occurrences of 'linux,stdout-path'.
| Search and replace all the of occurrences with 'stdout-path'.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
There is not firmware file with -ct-ct postfix, remove one -ct.
Fixes: 61b5b4971e ("mac80211: make ath10k-ct the default ath10k")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
We select ath10k-ct by default, but it is still possible to build
the upstream version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John Crispin <john@phrozen.org>
The current make-ras.sh image generation script for the ZyXEL NBG6617
has portability issues with bash. Because of this, factory images are
currently not built correctly by the OpenWRT buildbots.
This commit replaces the make-ras.sh by C-written mkrasimage.
The new mkrasimage is also compatible with other ZyXEL devices using
the ras image-format.
This is not tested with the NBG6616 but it correctly builds the
header for ZyXEL factory image.
Signed-off-by: David Bauer <mail@david-bauer.net>
- fix single spaces hidden by a tab
- replace indentation with spaces by tabs
- make empty lines empty
- drop trailing whitespace
- drop unnecessary blank lines
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
The upgrade led is only used if a running led is defined. If no running
led is defined, the upgrade led is ignored and upgrade isn't indicated
at all.
Instead, turn off the running led prior to turning the upgrade led on.
In most cases there isn't any visual change, but it allows to use an
independent led for upgrade indication.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Set the (sys)upgrade state when sourcing the stage2 script instead of
setting the state for each target individual.
This change fixes the, due to a missing state set, not working upgrade
led on ath79 and apm821xx.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Netgear R7800 switch LAN ports are numbered backwards in LuCI,
i.e. numbering is not corresponding to the actual physical port labels,
patch fixes that.
Signed-off-by: Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com>
[merged with existing board using the same config]
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
The original device support patch configured the amber wlan LEDs (which
are meant as error indicator by the OEM) controlled by the SOC's GPIO
as wlan traffic indicators, as the correct white wlan LEDs are
connected to GPIOs controlled by the QCA9984/ ath10k wlan cards were
not accessible. The recent addition of GPIO/ LED support to ath10k now
makes it possible to use the correct white LEDs instead - and
"mac80211: ath10k: use tpt LED trigger by default" also enables them by
default. While both LEDs are independent of each other (two separate
LEDs sharing one light tunnel), triggering both on wlan traffic is not
the intended behaviour (bright yellow light).
Tested on the ZyXEL NBG6817.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Remove the "firmware" partition definition from the DTS of R7800
to fix sysupgrade.
Commit 4645a6d3 defined CONFIG_MTD_SPLIT_UIMAGE_FW=y for ipq806x
and that causes mtd to misbehave as additional kernel and ubi
partitions are detected from inside the "firmware" partition.
[ 1.111324] 0x000001480000-0x000001880000 : "kernel"
[ 1.121005] 0x000001880000-0x000007900000 : "ubi"
[ 1.283912] 0x000007900000-0x000008000000 : "reserve"
[ 1.296407] 0x000001480000-0x000007900000 : "firmware"
[ 1.468043] no rootfs found after FIT image in "firmware"
[ 2.426860] 2 uimage-fw partitions found on MTD device firmware
[ 2.426931] 0x000001480000-0x000001880000 : "kernel"
[ 2.440420] 0x000001880000-0x000007900000 : "ubi"
Both kernel and ubi are already defined in DTS, so this duplication
leads into errors in sysupgrade:
Writing from <stdin> to kernel ...
ubiattach: error!: strtoul: unable to parse the number '6 mtd10'
ubiattach: error!: bad MTD device number: "6 mtd10"
The partition is defined to same area as kernel+ubi, and is not
needed for sysupgrade anymore. Remove it to fix things.
Only tested for the R7800 but all of them should behave equal.
Fixes: FS#1617
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
[squashed commits, add "tested on" note]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
Refresh patches.
Remove patch that can be reverse applied:
mvebu/patches-4.14/530-ATA-ahci_mvebu-enable-stop_engine-override.patch
mvebu/patches-4.14/531-ATA-ahci_mvebu-pmp-stop-errata-226.patch
Update patch that no longer applied:
ipq806x/patches-4.14/0035-clk-mux-Split-out-register-accessors-for-reuse.patch
Compiled-tested-for: lantiq, ramips
Run-tested-on: lantiq BT hh5a, ramips MIR3g
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Tested-by: Michael Yartys <michael.yartys@protonmail.com>
Tested-by: Rosen Penev <rosenp@gmail.com>
NEC Aterm WG2600HP is a 2.4/5 GHz band 11ac router, based on Qualcomm
IPQ8064.
Specification:
- IPQ8064 (384 - 1,400 MHz)
- 512 MB of RAM
- 32 MB of Flash (SPI)
- 4T4R 2.4/5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 12x LEDs, 4x keys
- 1x USB 3.0 Type-A
- UART header on PCB
- RX, TX, NC, GND, Vcc from power connector side
- baudrate: 115200 bps
Flash instruction using initramfs image:
1. Connect serial cable to UART header
2. Connect power cable and turn on the router
3. When the "Press the [f] key and hit [enter] to enter failsafe mode"
message is displayed on the console, press the "f" key and Enter key
sequentially to enter the failsafe mode
4. create fw_env.config file with following contents on failsafe mode:
/dev/mtd9 0x0 0x10000 0x10000
5. Execute following commands to add and change the environment
variables of U-Boot
fw_setenv ipaddr "192.168.0.1"
fw_setenv serverip "192.168.0.2"
fw_setenv autostart "yes"
fw_setenv bootcmd "tftpboot 0x44000000 wg2600hp-initramfs.bin;
bootipq"
6. Set the IP address of the computer to 192.168.0.2, connect to the LAN
port of WG2600HP, and start the TFTP server on the computer
7. Rename OpenWrt initramfs image for WG2600HP to
"wg2600hp-initramfs.bin" and place it in the TFTP directory
8. Remove power cable from WG2600HP, reconnect it and restart WG2600HP
9. WG2600HP downloads initramfs image from TFTP server on the computer,
loads it and boot with initramfs image
10. On the initramfs image, execute "mtd erase firmware" to erase stock
firmware and execute sysupgrade with the sysupgrade image
11. Wait ~180 seconds to complete flashing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Increase the available flash memory size in Netgear R7800
by taking into the use the unused "netgear" partition
that is located after the firmware partition.
Available flash space for kernel+rootfs+overlay increases
by 68 MB from 32 MB to 100 MB.
In a typical build, overlay space increases from 15 to 85,
increasing the package installation possibilities greatly.
Reverting to the OEM firmware is still possible, as the OEM
firmware contains logic to initialise the "netgear" partition
if its contents do not match expectations. In OEM firmware,
"netgear" contains 6 UBI sub-partitions that are defined in
/etc/netgear.cfg and initialisation is done by /etc/preinit
Tested with Openwrt master r7093-4fdc6ca31b and OEM V1.0.2.52
Reference to forum discussion in Netgear R7800 exploration thread:
https://forum.lede-project.org/t/netgear-r7800-exploration-ipq8065-qca9984/285/1118
(messages 1118-1158)
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
ipq806x is all dual core processors. ipq807x is quad core. Removes this
from dmesg:
RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
Signed-off-by: Rosen Penev <rosenp@gmail.com>
There's no spi-nor in R7800, so disable unequipped interfaces.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
These pins seem to be used by hw exclusively, so claiming it in
kernel causes an error in syslog in k4.14+.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
EA8500 has pcie2 slot unequipped.
By EA8500 hw design default pcie2 reset gpio (gpio63) is used to
reset the switch. That's why enabling pcie2 brings the switch into
a working state.
So let's just control the gpio63 without enabling the pcie2 slot.
We have to remove the pcie2_pins node so the gpio63 is not defined
twice. Because pcie2 node has a reference to pcie2_pins we have to
remove it as well.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
These nodes are common for all revisions so put it into SoC v1.0
dtsi file.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
USB PHY power settings introduced for ipq8065 SoC with commit
644a0d5 "ipq8065: adjust SS USB PHY power settings"
According to that commit msg and in correspondence to GPL tarballs
and related QSDK branch those settings are applied to ipq8064
SoCs of version >= 2.0.
https://github.com/paul-chambers/netgear-r7800/blob/master/git_home/linux.git/sourcecode/arch/arm/mach-msm/board-ipq806x.c#L2507-L2514
Now as we have clarified that mass market boards are of SoC v2.0
move those USB PHY settings from ipq8065 (v3.0 SoC) dtsi to
ipq8064 v2.0 dtsi.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
ipq8065 is ipq8064 v3.0
> socinfo_init: v6, id=280, ver=3.0, raw_id=17, raw_ver=17, hw_plat=0, hw_plat_ver=65536
Include dtsi accordingly and remove the unneeded qcom-ipq8065-v1.0.dtsi
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
According to OEM bootlog entry mass market devices are ipq8064 SoC
v2.0:
> socinfo_init: v6, id=202, ver=2.0, raw_id=2064, raw_ver=2064, hw_plat=0, hw_plat_ver=65536
I've checked C2600, EA8500 and VR2600v but couldn't find other
boards bootlog. I think it's safe to assume that other boards are
also v2.0. R7500 may be an exception because it was the first
device to hit the market.
So switch to v2.0 dtsi.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
According to QCA internal numbering there are 3 versions of
ipq8064/5 SoC:
ipq8064 v1.0 - probably ipq8064 evaluation boards only
ipq8064 v2.0 - probably ipq8064 mass market boards only
ipq8064 v3.0 - aka ipq8065, boards based on ipq8065.
Each next revision includes configuration differences from
previous revision and adds something new.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
It keeps failing (R7800) with the stack trace below
BUG: scheduling while atomic: kworker/0:1/26/0x00000002
(unwind_backtrace) from [<c02121d0>] (show_stack+0x10/0x14)
(show_stack) from [<c03932e4>] (dump_stack+0x7c/0x9c)
(dump_stack) from [<c0239b90>] (__schedule_bug+0x5c/0x80)
(__schedule_bug) from [<c05b7260>] (__schedule+0x50/0x3f4)
(__schedule) from [<c05b76a8>] (schedule+0xa4/0xd4)
(schedule) from [<c05ba430>] (schedule_hrtimeout_range_clock+0xc8/0x100)
(schedule_hrtimeout_range_clock) from [<c05ba480>]
(schedule_hrtimeout_range+0x18/0x20)
(schedule_hrtimeout_range) from [<c05b9f78>] (usleep_range+0x48/0x50)
(usleep_range) from [<c03f333c>] (__clk_hfpll_enable+0x44/0xd0)
(__clk_hfpll_enable) from [<c03f3474>] (clk_hfpll_set_rate+0xac/0xc4)
(clk_hfpll_set_rate) from [<c03ec390>] (clk_change_rate+0xf4/0x1fc)
(clk_change_rate) from [<c03ec510>] (clk_core_set_rate_nolock+0x78/0x94)
(clk_core_set_rate_nolock) from [<c03ec54c>] (clk_set_rate+0x20/0x30)
(clk_set_rate) from [<c0424168>] (dev_pm_opp_set_rate+0x190/0x26c)
(dev_pm_opp_set_rate) from [<c04a8548>] (set_target+0x40/0x108)
(set_target) from [<c04a4.140>] (__cpufreq_driver_target+0x3f4/0x488)
(__cpufreq_driver_target) from [<c04a7494>] (od_dbs_timer+0xcc/0x154)
(od_dbs_timer) from [<c04a7998>] (dbs_work_handler+0x2c/0x54)
(dbs_work_handler) from [<c02309e8>] (process_one_work+0x1c0/0x2f0)
(process_one_work) from [<c02319a8>] (worker_thread+0x2a4/0x404)
(worker_thread) from [<c0235944>] (kthread+0xd8/0xe8)
(kthread) from [<c020eef0>] (ret_from_fork+0x14/0x24)
Signed-off-by: Marc Benoit <marcb62185@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Starting with kernel 4.14 and gcc 7, the kernel doesn't fit into the
2 MB reserved for the kernel partition by the OEM firmware anymore.
This patch increases the kernel partition from 2 MB to 4 MB, at the
expense of the rootfs, for all supported kernels.
WARNING: This breaks sysupgrade! Flashing a firmware containing this
changed partitioning from an older image with 2 MB reserved for the
kernel partion requires the tftp recovery procedure, thereby losing
all settings.
This change follows the functional example of the Netgear r7800, but
has not been runtime tested on a Netgear Nighthawk X4 R7500v2.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Starting with kernel 4.14 and gcc 7, the kernel doesn't fit into the
2 MB reserved for the kernel partition by the OEM firmware anymore.
This patch increases the kernel partition from 2 MB to 4 MB, at the
expense of the rootfs, for all supported kernels.
WARNING: This breaks sysupgrade! Flashing a firmware containing this
changed partitioning from an older image with 2 MB reserved for the
kernel partion requires the tftp recovery procedure, thereby losing
all settings.
This change follows the functional example of the Netgear r7800, but
has not been runtime tested on a Netgear Nighthawk X4 R7500
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Cc: Jonas Gorski <jonas.gorski@gmail.com>
Starting with kernel 4.14 and gcc 7, the kernel doesn't fit into the
2 MB reserved for the kernel partition by the OEM firmware anymore.
This patch increases the kernel partition from 2 MB to 4 MB, at the
expense of the rootfs, for all supported kernels.
WARNING: This breaks sysupgrade! Flashing a firmware containing this
changed partitioning from an older image with 2 MB reserved for the
kernel partion requires the tftp recovery procedure, thereby losing
all settings.
This change follows the functional example of the Netgear r7800, but
has not been runtime tested on a Netgear Nighthawk X4 D7800.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Cc: Tathagata Das <tathagata@alumnux.com>
The default image does not fit 2 MB anymore, expand kernel partition
to 3 MB.
Upgrading should work transparently via sysupgrade in both directions.
Another option would be to merge "kernel" and "rootfs" into a single
"firmware" partition using MTD_SPLIT_TPLINK_FW, but just changing the
sizes of the existing partitioning has been deemed safer in the absence
of an actual runtime test on an affected device; the maximum for rootfs
changes from 10.4 MB to 9.4 MB.
This change follows the example for the TP-Link Archer C2600, but has
not been runtime tested on a TP-Link Archer VR2600v.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Cc: Sebastian Quilitz <zeraphim@x-pantion.de>
The default image does not fit 2 MB anymore, expand os-image partition
to 4 MB.
Upgrading works transparently via sysupgrade in both directions.
Another option would have been to merge "os-image" and "rootfs" into a
single "firmware" partition using MTD_SPLIT_TPLINK_FW, but just
changing the sizes of the existing partitioning has been deemed safer
and actually tested on an affected device; the maximum for rootfs
changes from 27 MB to 25 MB.
Run-tested on TP-Link Archer C2600.
Signed-off-by: Joris de Vries <joris@apptrician.nl>
[slh: extend comments and commit message, rename rootfs]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Starting with kernel 4.14 and gcc 7, the kernel doesn't fit into the
2 MB reserved for the kernel partition by the OEM firmware anymore.
This patch increases the kernel partition from 2 MB to 4 MB, at the
expense of the rootfs, for all supported kernels.
WARNING: This breaks sysupgrade! Flashing a firmware containing this
changed partitioning from an older image with 2 MB reserved for the
kernel partion requires the tftp recovery procedure, thereby losing
all settings.
This patch is based on a corresponding change by Pavel Kubelun
<be.dissent@gmail.com> and has been tested by Michael Yartys
<michael.yartys@protonmail.com>
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Disable MSM8960, MSM8974 and APQ8084
- since these are different SoC's than IPQ806x
Removed unrequired serial configs
- since ipq806x uses SERIAL_MSM only
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
- Rebased the patches for 4.14
- Dropped spi-qup and 0027, 0028, 0029
clk patches since it's already included
in upstream.
Tested on IPQ AP148 Board:
1) NOR boot and NAND boot
2) Tested USB and PCIe interfaces
3) WDOG test
4) cpu frequency scaling
5) ethernet, 2G and 5G WiFi
6) ubi sysupgrade
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Merge the two existing functions and use a parameter for the type
header field.
It updates the syntax of the former mpc85xx fake ramdisk header
command to be compatible with mkimage from u-boot 2018.03 and fixes the
build error spotted by the build bot.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This solution is more upstream compatible as it only requires specifying
of_match_table in the parser code and doesn't depend on linux,part-probe
which is solution made generic by a LEDE downstream patch that can't be
upstreamed.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Acked-by: John Crispin <john@phrozen.org>
Hardware highlights:
- SoC: Qualcomm Atheros IPQ8064/5 ARM Dual Core CPU
- RAM: (512MB or 1GB) DDR3 System Memory
- Storage: 32MB NOR (Cypress S25FL256S1)
256MB NAND (Micron MT29F2G08ABBEAH4)
- Ethernet: 5 x 1G via QCA8337N
- USB: 1 x USB 2.0/3.0 + 1 x USB 2.0 on mini PCIe3 socket
- PCIe: 3x mini PCIe (third mini PCIE3 is PCIe/USB shared)
- SIM Card Slot: 2 x Slot
- Buttons: Reset Button
- LEDs: 18x, 8x GPIO controllable
- Buzzer
The correct amount of RAM will be passed by the bootloader.
In contrast to the documentation provided by Compex, the third PCIe
doesn't use GPIO16 for PERST. Instead, GPIO3 is shared and used as PERST
for PCIe0 and PCIe2.
So far, no one was able to get USB 3.0 working with the 1GB RAM version,
while it works fine for my 512MB version. Since USB 3.0 doesn't work with
the Compex firmware for the 1G variant either, it could be a hardware
issue with these boards.
OpenWrt will be installed to the NAND flash. Make sure to have a full
working image on the NOR flash. It will be the backup in case anything
goes wrong.
It has been observed that an image loaded via tftpboot might have
bitflips. Hence the extra step to create a crc32 checksum to allow to
compare the checksum with the one from the source file prior to flashing.
In all cases it is necessary to set the following u-boot parameter to an
empty (whitespace) value, to ensure that the chosen bootargs of the dts
isn't overwritten or set to bogus - not working - values:
(IPQ) # set bootargs " "
(IPQ) # set fsbootargs " "
(IPQ) # saveenv
The sysupgrade image can be installed directly on flash using u-boot (put
jumper in JP13 (leave JP9 open) to boot from nand):
(IPQ) # set serverip 192.168.1.20
(IPQ) # set ipaddr 192.168.1.1
(IPQ) # tftpboot 0x42000000 openwrt-ipq806x-compex_wpq864-squashfs-nand-factory.bin
(IPQ) # crc32 0x42000000 $filesize
(IPQ) # nand erase 0x1340000 0x4000000
(IPQ) # nand write 0x42000000 0x1340000 $filesize
The initramfs image can be started using:
(IPQ) # set fdt_high 0x48000000
(IPQ) # tftpboot 0x44000000 openwrt-ipq806x-compex_wpq864-initramfs-fit-uImage.itb
(IPQ) # bootm 0x44000000
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch adds support for GL.iNet GL-B1300
Specification:
- SOC: IPQ4028 / QCA Dakota
- RAM: 256 MiB
- FLASH: 32 MiB
- ETH: Qualcomm Atheros QCA8075 Gigabit Switch (2 x LAN, 1 x WAN)
- USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
- WLAN1: Qualcomm Atheros QCA4028 2.4GHz 802.11bgn 2:2x2
- WLAN2: Qualcomm Atheros QCA4028 5GHz 802.11a/n/ac 2:2x2
- INPUT: one reset and one WPS button
- LEDS: 3 leds: Power, WIFI(only for 2.4G currently), and one reserved
- UART: 1 x UART on PCB (3.3V, TX, RX, GND) - 115200 8N1
Installation:
Method 1:
- use serial port to stop uboot
- uboot command: run lf
Method 2:
- push down reset button and power on
- wait until three leds constantly on then release
- upgrade by uboot web at http://192.168.1.1
Note:
- the sysupgrade image need to be renamed to lede-gl-b1300.bin in both method.
- the sysupgrade image can be automatically downloaded if tftp server at
192.168.1.2 have that file.
- the wifi led will be flashing when writing image.
Signed-off-by: Dongming Han <handongming@gl-inet.com>
Instead of writing to the currently booted partition set, this
implements full dual-boot support for sysupgrade by always writing to
the other, currently inactive, partition set and toggling the dualflag
after a successful flash.
The currently active/ booted partition set is determined by parsing
/proc/cmdline for its rootfs parameter (supplied by the DTS), instead
of reading from the 0:DUAL_FLAG mtd, in order to prevent (potentially)
bricking both partition sets.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Instead of hardcoding /dev/loop0, it's safer to query for the first
free loop device and assign that dynamically. While /dev/loop0 is a
reasonable assumption immediately following "losetup --detach-all",
detaching the mounted overlay is no longer strictly necessary once
dual-boot support has been added for the nbg6817.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Harmonize the variable usage for $kernel and $rootfs to always contain
the full device path, instead of just its basename.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
PHY drivers were grouped into vendor specific directories
by upstream commit 0b56e9a7e8358e59b21d8a425e463072bfae523c
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
The BDFs for OpenMesh A42 were upstreamed [1] to the ath10k-firmware
repository and are now part of ath10k-firmware 2018-01-26. The
ipq-wifi-openmesh_a42 package can now be dropped because OpenWrt already
ships the QCA4019 board-2.bin from this version.
[1] https://wireless.wiki.kernel.org/en/users/drivers/ath10k/boardfiles
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
This commit marks the CPUs switchport explicit as untagged.
Otherwise, an eth0.1 interface is created and the devices
LAN-ports are not working.
Signed-off-by: David Bauer <mail@david-bauer.net>
Some part of this patch was added to the generic patches as it was
needed also for some other target. Do not add it here any more.
Fixes: 02050f7e7d ("kernel/4.{4, 9}: add manufacturer ID for Winbond NANDs")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The patch 0022-dts-ipq4019-support-ARMv7-PMU.patch
was merged into 4.8-rc1.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[refresh patches]
Signed-off-by: Mathias Kresin <dev@kresin.me>
During the integration of the ipq40xx target,
the phy drivers were included into the ipq806x's
target kernel config.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch renames the AVM FRITZ!Box 4040's board-2.bin
file and package to match the 'vendor_product' format.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch aligns the device-tree file with the latest
guidelines.
- No longer include qcom-ipq4019-ap.dk01.1.dtsi. This
file is only partially upstream and therefore subjected
to changes that might not be compatible with the board.
As a result, the definitions from the file have been
copied into this dts.
- exclusively use decimal GPIO addresses.
- reorganize the reserved-memory layout to waste less
memory. There's no point in keeping the u-boot loader
around. This should also make it possible to create
an image that will boot with the original EVA/ADAM2 loader
without needing to install the modified u-boot loader.
And finally mark the "tz-apps" as reusable.
There isn't a way to upload apps to the trust-zone in OpenWrt
yet. But it might see some use in the future as a "secure"
key-store/TPM.
- sort the first-level nodes alphabetically.
- sort nodes with an address by the address.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Use the first found directory in the tar archive instead of relying on
a directory named according to the userspace boardname.
It allows to change the boardname without adding another compatibility
layer to the zyxel sysupgrade.
Fixes: 33f09cf151 ("ipq806x: convert to dt-based board-detection")
Signed-off-by: Mathias Kresin <dev@kresin.me>
Picking commit from QSDK
https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/?h=eggplant&id=a86bda9f8a7965f0cedd347a9c04800eb9f41ea3
Commit message:
"During removal of the glue layer(dwc3-of-simple), USB master reset is set to active and during insertion it is de-activated."
Change-Id: I537dc810f6cb2a46664ee674840145066432b957
Signed-off-by: Vasudevan Murugesan <vmuruges@codeaurora.org>
(cherry picked from commit 4611e13580a216812f85f0801b95442d02eeb836)"
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
A newer clk and cpufreq drivers for ipq806x platform had been sent upstream.
A change that i have noticed is that now it's possible to set min, cur and max frequencies from sysfs (previously it was bugged and caused nothing).
Following patches are removed:
- 0036-clk-Avoid-sending-high-rates-to-downstream-clocks-du.patch - seems it was dropped from the patchset by current committer.
- 0044-clk-qcom-krait-Remove-CLK_IS_ROOT.patch - already applied to the driver itself in the corresponding patch.
- 0057-clk-qcom-Add-regmap-mux-div-clocks-support.patch - seem to be irrelevant to ipq806x.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
According to QSDK and OEM tarballs (checked c2600, r7500v2, r7800) 2nd pci slot (pci1, 2,4 GHz card)) on ap148 based boards should operate in gen1 mode.
EA8500 is an exception and according to GPL pcie0 should operate in gen1 mode.
In previous commit we've added the support for this option, so enable it in DT for affected devices.
QSDK ref:
https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/?h=release/endive_preview_cc&id=f3b07fe309027c52fc163149500cedddd707c506
While at it move the phy transmit termination offset value into dtsi file as it's platform specific.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
In current state there's huge regression on ipq806x target that causes the device to transmit broken/malformed frames that are not corrected/detected by error control mechanisms and other less severe issues.
https://bugs.lede-project.org/index.php?do=details&task_id=1197
This finally had been narrowed down to patch 0071-pcie-qcom-fixes.patch
Meanwhile QSDK contains a handful of commits that add support for ipq806x to upstream qcom pcie driver
https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/log/drivers/pci/host/pcie-qcom.c?h=eggplant
Unfortunately qca developers do not bother to push it upstream.
Using those commits instead of lede 0071 patch fixes mentioned issue and probably many others as it seems that corrupted data has been originating within pcie misconfiguration.
Fixes: FS#1197 and probably others
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Ubifs is disabled for all boards except the evaluation boards and the
Fritz!Box 4040 anyway. According the author, the ubifs support for the
Fritz!Box 4040 wasn't enabled on purpose.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Remove leftover code used for legacy images. There are no relevant
binary differences for the images after removing the legacy leftovers.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Initialise the filesystem specific build command. Otherwise it will be
unintended inherit to following images and will cause a wrong image
format.
The issue is around for ages but was only recently triggered due to the
added support for the Openmesh a42.
Fixes: FS#1276
Signed-off-by: Mathias Kresin <dev@kresin.me>
* QCA IPQ401x
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=OM-A42
* 2T2R 5 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=OM-A42
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
- triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
* powered only via POE
- 802.3af POE on Ethernet 1
- 18-24v passive POE (mode B) on Ethernet 2
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
The kernel driver gpio-wdt or the userspace tool om-watchdog can be used to
trigger external gpio watchdog chips. The gpio-wdt driver has the benefit
that it can be configured together with the rest of the device in the DTS
and better integrates in the OpenWrt via procd.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Use the generic board detection method:
- Board name: First compatible string from the device tree
- Board model: Model property from the device tree
Change occurrences of board name in userspace by the compatible
string, and removed target specific board detection script
Replace the definition of SUPPORTED_DEVICES in Device/Default
to extract the dt compatible string from each device definition.
Additionally, for devices supported by lede-17.01, append
the value of BOARD_NAME to SUPPORTED_DEVICES in the device
definition.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Use <manufacturer>_<modelname> as image name for board using the
devicetree compat string as boardname.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
This will allow to maintain the current syntax for LEDs config
when switching to a device tree compatible string boardname.
None of the current boards use a comma in the boardname, so they
will be unaffected.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
There are only artifacts for these boards in our tree and not even
partial support.
Drop teh stale files.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Lantiq and IPQ806X (which includes IPQ40XX) both define the
same custom function {ipq806x|lantiq}_get_dt_led.
This patch moves the function into the base-file package at
lib/functions/leds.sh to make it more accessible for other
targets as well.
Cc: Mathias Kresin <dev@kresin.me>
Cc: John Crispin <john@phrozen.org>
Cc: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This will avoid some conflicts when doing a git rebase or merge,
specially when adding support to a new device.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
[drop brcm47xx changes which rename the images]
Signed-off-by: Mathias Kresin <dev@kresin.me>
This changes the cmdline from:
Kernel command line: root=/dev/mmcblk0p5 rootfstype=squashfs,ext4 rootwait noinitrd
Bootloader command line (ignored): board=NBG6817 root=/dev/mmcblk0p5 rootwait zld_ver=2.04 console=ttyHSL1,115200n8 mtdparts=m25p80:0xC0000(SBL)ro,0x40000(TZ)ro,0x40000(RPM)ro,0x80000(u-boot)ro,0x10000(env)ro,0x10000(ART)ro,0x10000(dualflag),0x210000(reserved)
to
Kernel command line: rootfstype=squashfs,ext4 rootwait noinitrd root=/dev/mmcblk0p5
Bootloader command line (ignored): board=NBG6817 root=/dev/mmcblk0p5 rootwait zld_ver=2.04 console=ttyHSL1,115200n8 mtdparts=m25p80:0xC0000(SBL)ro,0x40000(TZ)ro,0x40000(RPM)ro,0x80000(u-boot)ro,0x10000(env)ro,0x10000(ART)ro,0x10000(dualflag),0x210000(reserved)
As a consequence booting from the alternative dual-boot partition set
(root=/dev/mmcblk0p8) becomes possible.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
AP-DK01.1-C1 is QCA dev board with:
- ipq4018 quad core ARM @716.8MHz, 2x2 dual (11n+11ac) radio
- 256MB RAM
- 32MB SPI flash
- QCA8075 multiport ethernet phy (WAN port, 4x LAN ports)
First installation via u-boot:
sf probe
sf erase 0x180000 0x1a00000
tftpboot 0x84000000 lede-ipq806x-AP-DK01.1-C1-squashfs-sysupgrade.bin
sf write 0x84000000 0x180000 $filesize
Further upgrades via sysupgrade.
Changes:
- add partitions
- set memory size to 256MB
- add reserved memory mapping
- add correct compatible string
- add image generation
- extract pre-cal data from ART partition
Compile and run tested.
Wirespeed NAT can be achieved with spreading rx interrupts over different
cores. Wifi speed is ~550Mbps @5GHz in open air.
Note:
AP-DK01.1-C1 is fully compatible with AP-DK01.2-C1, which has
ipq4028 instead of ipq4018 on board.
Changes since v2:
- based on dts(i) rework/cleanup submitted:
http://lists.infradead.org/pipermail/lede-dev/2017-October/009596.html
- precise reserved memory mapping
- more precise description
- compatible string
Signed-off-by: Roman Yeryomin <roman@advem.lv>
Supported frequencies of all ipq40xx chips are 48, 200, 500 and 716.8 MHz.
Previous 666MHz setting was most likely related to instability of early
chips/boards made before mass production.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
The ZyXEL NBG6817 calculates all MAC addresses based on the ethaddr
value stored in the U-Boot environment (0:APPSBLENV). No MAC addresses
are stored in the ART partition and the generated MAC addresses for the
wlan interfaces alternate randomly between 12:34:56:78:90:12 and
00:03:7f:12:34:56.
interface new/ OEM MAC old MAC
wlan-2.4g (phy1): ethaddr undefined
wlan-5g (phy0): ethaddr + 1 undefined
lan : ethaddr + 2 ethaddr
wan : ethaddr + 3 ethaddr + 1
This patch defines stable MAC addresses for the wlan interfaces for
the first time instead of generating them at random. The previously
defined values for lan/ wan are changed to follow the settings of the
OEM firmware.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
The ZyXEL NBG6817 uses an eMMC flash for the rootfs, which is split
into the readonly squashfs and ext4 for the overlay. This adds the
required package to the device packages to allow mounting the overlay
by default.
/dev/root on /rom type squashfs (ro,relatime)
proc on /proc type proc (rw,nosuid,nodev,noexec,noatime)
sysfs on /sys type sysfs (rw,nosuid,nodev,noexec,noatime)
tmpfs on /tmp type tmpfs (rw,nosuid,nodev,noatime)
/dev/loop0 on /overlay type ext4 (rw,noatime,data=ordered)
overlayfs:/overlay on / type overlay (rw,noatime,lowerdir=/,upperdir=/overlay/upper,workdir=/overlay/work)
tmpfs on /dev type tmpfs (rw,nosuid,relatime,size=512k,mode=755)
devpts on /dev/pts type devpts (rw,nosuid,noexec,relatime,mode=600,ptmxmode=000)
debugfs on /sys/kernel/debug type debugfs (rw,noatime)
mountd(pid1040) on /tmp/run/blockd type autofs (rw,relatime,fd=7,pgrp=1,timeout=30,minproto=5,maxproto=5,indirect)
Before this commit, the ext4 based overlayfs could not be mounted,
which left only the tmpfs based/ volatile emergency overlay in place.
Fixes: https://forum.lede-project.org/t/zyxel-nbg6817-flashing-from-oem/768
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
IMG_PREFIX can be modified in ImageBuilder by passing EXTRA_IMAGE_NAME
on command line, but Image/Prepare is not run in ImageBuilder. This
causes missing files when IMG_PREFIX is used for target file names in
Image/Prepare, then as source file names in Image/BuildKernel or
Image/Build.
Fix this by using a fixed output file name in Image/Prepare, and copy to
the expected file name in Image/BuildKernel instead, which is run by
ImageBuilder.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Zyxel NBG6817 features a WiFi button, which becomes functional by setting
correct GPIO. It is a switch-type button, so it emits KEY_RFKILL on each ON
and OFF state. This is achieved by setting input-type to EV_SW.
Signed-off-by: Tolga Cakir <tolga@cevel.net>
Refresh patches.
Compile-tested on ipq8065/nbg6817 and x86/64.
Runtime-tested on ipq8065/nbg6817 and x86/64.
Fixes CVE-2017-1000251.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
[adapt qcom_nandc.c patches to match upstream changes, test ipq8065/nbg6817]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
The order of LAN ports shown in Luci is reversed compared to what is
written on the case of the device. Fix the order so that they match.
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
Refresh patches.
Adapt 704-phy-no-genphy-soft-reset.patch.
Remove brcm2708/950-0005-mm-Remove-the-PFN-busy-warning.patch.
Compile-tested on brcm2708/bcm2708 and x86/64.
Runtime-tested on brcm2708/bcm2708 and x86/64.
Fixes the following vulnerabilities:
- CVE-2017-7533
- CVE-2017-1000111
- CVE-2017-1000112
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Do not parse /tmp/sysinfo/board_name, /proc/cpuinfo or the device tree
compatible string directly. Always use the board_name function to get
the board name.
The admswconfig package still reads /proc/cpuinfo directly. The code
looks somehow broken and the whole adm5120 which uses this package
looks unmaintained. Leave it as it is for now.
Signed-off-by: Mathias Kresin <dev@kresin.me>
For targets using the generic board detection and board specific
settings in diag.sh, the board name is still unset at the time the
set_state() provided by diag.sh is called by 10_indicate_preinit.
Change the execution order to ensure the boardname is populated before
required the first time. Do the target specific board detection as
early as possible, directly followed by the generic one to allow a
seamless switch to the generic function for populating /tmp/sysinfo/.
Signed-off-by: Mathias Kresin <dev@kresin.me>
