While converting Nanostation M XW from current ar71xx code to ath79 I've
hit one issue, where the ethernet networking wasn't working, so I was
checking every bit in the networking setup path between ar71xx and
ath79.
I've came to the following code in ar71xx/mach-ubnt-xm.c:
static void __init ubnt_xw_init(void) {
...
ath79_setup_ar934x_eth_cfg(AR934X_ETH_CFG_MII_GMAC0 |
AR934X_ETH_CFG_MII_GMAC0_SLAVE);
...
}
Where this code is setting AR934X_ETH_CFG_MII_GMAC0_SLAVE bit in
AR934X_GMAC_REG_ETH_CFG register, but I couldn't find a way of setting
this bit from DTS, so this patch adds `mii-gmac0-slave` DTS property
which allows setting of this bit in `gmac-config`, which is then used in
Nanostation M XW DTS.
Tested-by: Joe Ayers <ae6xe@arrl.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This allows resetting gmac registers during initialization.
Also add compatible string for qca955x mdio to enable more mdio
clock dividers.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
On ar933x and later chips, there are separated mac/mdio resets, but
resetting the entire gmac block with register values requires both
mac_reset and mdio_reset to be asserted together.
Add support for optional mdio reset so that we can do a full reset
if needed.
This patch also replaced deprecated devm_reset_control_get for
mac reset.
To use this feature, the following is needed:
1. drop "simple-mfd" compatible to register mdio0 after gmac init
so that mdio registers aren't reset after initialization.
2. move mdio reset from mdio-bus to its parent eth node.
NOTE: This can't be applied on gmac1 with builtin switch since we
haven't add a feature to defer probe if phy connection failed.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
remove the hacky checking of "simple-mfd" compatible
also add some comments explaining that piece of code.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
using the devm api makes the code simpler.
also drop unneeded memory free from ag71xx_remove since they are
allocated using devm apis.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
phy_modes() in phy.h can convert PHY modes to string with supports
for all available PHY modes.
Also add a space in mode printing to make it look better.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Refactor pcie-oxnas to have shared resources in syscon and new pcie-phy
driver. Hopefully this revives PCIe...
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
At some point our initramfs image grew over 6MB, which is
causing an issue when uncompressing in the stock bootloader:
=> bootm 0x5000000 - 0x1000000;
Image Name: Linux-4.19.24
Created: 2019-02-23 1:58:20 UTC
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 6752470 Bytes = 6.4 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Booting using the fdt blob at 0x1000000
Uncompressing Kernel Image ... Error: inflate() returned -5
GUNZIP: uncompress, out-of-mem or overwrite error - must RESET
board to recover
Loading Device Tree to 00ffa000, end 00fffc78 ... OK
To get around this, we need to move to an uncompressed image
for the initramfs image. While this makes a larger image, it
is thankfully bootable so people can then convert their
devices to run OpenWRT. It's worth noting the non-initramfs
image is under 3M, so it will be ages before we have any issues
with the flashed kernel.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[keep commit message at less than 75 characters per line]
This commit makes the TP-Link hardware-revision naming consistent to
match the one used by the vendor. TP-Link refers to the different
revisions as "vX" not "Version X".
Signed-off-by: David Bauer <mail@david-bauer.net>
Device specification:
- SoC: Ralink RT3883 (MIPS 74Kc) 500Mhz
- RAM: 64Mb
- Flash: 8MB (SPI-NOR)
- Ethernet: 10/100/1000 Mbps
- WLAN
Wireless 1: SoC-integrated : 2.4/5 GHz
Wireless 2: 2.4 GHz RT3092L
- LED: 2x USB, WAN, LAN
- Key: WPS, reset
- Serial: 4-pin header, (57600,8,N,1), 3.3V TTL,
GND, RX, TX, V - J12 marking on board
- USB ports: 2 x USB 2.0
Flashing instructions:
Option 1 (from bootloader web)
- Hold reset button on the back of router when plugging
in power (for at-least 10 seconds after plugged in)
- Connect to a Lan port
- Set computer IP to 10.10.10.3
- Go to http://10.10.10.123 in a web browser
- Click the Browse... Button and select the
*squashfs.sysupgrade.bin file then click APPLY
Option 2 (from the stock admin web)
- Go to firmware upgrade
- Upload the **factory** image *initramfs.bin first
- Boot into openwrt
- From Luci web in openwrt upload the *squashfs.sysupgrade.bin
Signed-off-by: Kip Porterfield <kip.porterfield@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[added v1 to the compatible identifier, added pciid for
the RT3092L, fixed pci unit-address, split out the F9K110X.dtsi
to prepare for a possible F9K1103 patch]
Commit 34b10b46 made usb match with the corresponding usb label.
The problem is that v4 seems to use in stock firmware the
upper led for usb 1 and the lower led for usb 2.
The led assigned varies between TP-Link models and even
same model versions. For example, Archer C7 v1 and v2 have
the leds in the reverse order.
Revert 34b10b46 and swap led labels instead, now usb port
and led label match and also respect the original behavior.
Tested-by: Oldrich Jedlicka <oldium.pro@gmail.com>
Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
The linux-4.14.99 had introduced below upstream patch.
6636dc5e01c6 arm64: io: Ensure value passed to __iormb() is held in a 64-bit register
It was causing VFIO driver build issue. This patch is to fix it.
CC drivers/vfio/fsl-mc/vfio_fsl_mc.o
In file included from ./include/linux/scatterlist.h:9:0,
from ./include/linux/iommu.h:22,
from drivers/vfio/fsl-mc/vfio_fsl_mc.c:14:
drivers/vfio/fsl-mc/vfio_fsl_mc.c: In function 'vfio_fsl_mc_dprc_wait_for_response':
./arch/arm64/include/asm/io.h:122:45: error: expected expression before ')' token
: "=r" (tmp) : "r" ((unsigned long)(v)) \
^
drivers/vfio/fsl-mc/vfio_fsl_mc.c:334:3: note: in expansion of macro '__iormb'
__iormb();
^~~~~~~
./arch/arm64/include/asm/io.h:122:45: error: expected expression before ')' token
: "=r" (tmp) : "r" ((unsigned long)(v)) \
^
drivers/vfio/fsl-mc/vfio_fsl_mc.c:336:3: note: in expansion of macro '__iormb'
__iormb();
^~~~~~~
Reported-by: Mathew McBride <matt@traverse.com.au>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reading and writing to and from flash storage is slow and currently,
the ath10kcal_extract() scripts are even more at an disadvantage
because they use a block size of 1 to be able skip.
This patch reworks the extraction scripts to be much faster and
efficient by reading and writing the calibration data in possibly
one big block.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This is a simple copy of ipq40xx: speed up ath10k-caldata
extraction commit a69e101ed1
Tested on DIR-825-B1
3768+0 records in
3768+0 records out
real 0m 11.90s
user 0m 0.03s
sys 0m 9.94s
1+0 records in
1+0 records out
real 0m 0.03s
user 0m 0.00s
sys 0m 0.03s
With this change eeprom extraction is fast enough to get
working Wi-Fi after initial install.
Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
This patch adds more disabled DRM config symbols from the
x86' config to the generic target configs. The existing
symbols in the x86' configs are kept for now, until we
know whenever we want to remove such symbols or not
(see Github PR #1831, #1825, #1828).
THis patch also contains a squashed patch from
Daniel Engberg <daniel.engberg.lists@pyret.net> titled
"kernel: Fix config for 4.14" which fixes a duplicated line
added by: commit 8bdc241d01 ("x86: fix geode image builds")
Fixes: 8bdc241d01 ("x86: fix geode image builds")
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
All supported boards should work with the $vendor bootloader just fine.
Existing users should mindfully re-flash using new initramfs build and
restore $vendor bootloader's bootcmd to it's original setting.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add port handles for both USB 2.0 ports so they can be used as
trigger-source for USB LEDs.
Suggestions for pogoplug and akitio,mycloud devices are welcome.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
add kernel and other missing NAND flash partitions to allow booting
using stock loader instead of the 2nd-stage bootloader.
This will ease installation from stock firmware on pogoplugs as well
as stg212 aka. medion nas.
Existing users of OpenWrt on those boards will have to boot initramfs
generated after this commit and subsequently flash first the ubinized
image, then again run initramfs to flash sysupgrade.tar image, and
then restore bootcmd in U-Boot environment back to the original setting
('nboot 60500000 0 440000' or something like that) instead of jumping
into the now no longer used 2nd-stage loader.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
NEC WG2600HP uses port1 on QCA8337 as a WAN port, so "0x2" should
be used as a portmask instead of "0x1e" for "WAN" LED configuration.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This patch changes all the legacy usbdev leds triggers
to the use usbport. The problem is that the usbdev triggers
get applied as usbport in sysfs but LuCI gets confused and
is not able to show the configuration with usbdev. More
information can be found in the PR:
<https://github.com/openwrt/openwrt/pull/1819>
Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[extended commit message]
In the production of glinet, the MAC address of ethernet port is
only written at the position where the ART area offset address
is 0, and the MAC address of eth1 is added 1 on the basis of eth0.
Signed-off-by: Luo chongjun <luochongjun@gl-inet.com>
Hardware
--------
CPU: Qualcomm IPQ4019
RAM: 256M
FLASH: 128M NAND
ETH: QCA8075
VDSL: Intel/Lantiq VRX518 PCIe attached
currently not supported
DECT: Dialog SC14448
currently not supported
WiFi2: IPQ4019 2T2R 2SS b/g/n
WiFi5: IPQ4019 2T2R 2SS n/ac
LED: - Power/DSL green
- WLAN green
- FON/DECT green
- Connect/WPS green
- Info green
- Info red
BTN: - WLAN
- FON
- WPS/Connect
UART: 115200n8 3.3V (located under the Dialog chip)
VCC - RX - TX - GND (Square is VCC)
Installation
------------
1. Grab the uboot for the Device from the 'u-boot-fritz7530'
subdirectory. Place it in the same directory as the 'eva_ramboot.py'
script. It is located in the 'scripts/flashing' subdirectory of the
OpenWRT tree.
2. Assign yourself the IP address 192.168.178.10/24. Connect your
Computer to one of the boxes LAN ports.
3. Connect Power to the Box. As soon as the LAN port of your computer
shows link, load the U-Boot to the box using following command.
> ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz7530.bin
4. The U-Boot will now start. Now assign yourself the IP address
192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP
server root directory and rename it to 'FRITZ7530.bin'.
5. The Box will now boot OpenWRT from RAM. This can take up to two
minutes.
6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using
scp. SSH into the Box and first write the Bootloader to both previous
kernel partitions.
> mtd write /path/to/uboot-fritz7530.bin uboot0
> mtd write /path/to/uboot-fritz7530.bin uboot1
7. Remove the AVM filesystem partitions to make room for our kernel +
rootfs + overlayfs.
> ubirmvol /dev/ubi0 --name=avm_filesys_0
> ubirmvol /dev/ubi0 --name=avm_filesys_1
8. Flash OpenWRT peristently using sysupgrade.
> sysupgrade -n /path/to/openwrt-sysupgrade.bin
Signed-off-by: David Bauer <mail@david-bauer.net>
[removed pcie-dts range node, refreshed on top of AP120-AC/E2600AC]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
From: Niklas Cassel <niklas.cassel@linaro.org>
|The databook clearly states that the MSI IRQ (msi_ctrl_int) is a level
|triggered interrupt.
|
|The msi_ctrl_int will be high for as long as any MSI status bit is set,
|thus the IRQ type should be set to IRQ_TYPE_LEVEL_HIGH, causing the
|IRQ handler to keep getting called, as long as any MSI status bit is set.
|[...]
|Not having the correct IRQ type defined will cause us to lose interrupts,
|which in turn causes timeouts in the PCIe endpoint drivers.
|
|Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
|Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
David Bauer reported that the VDSL modem (attached via PCIe)
on his AVM Fritz!Box 7530 was complaining about not having
enough space in the BAR. A closer inspection of the old
qcom-ipq40xx.dtsi pulled from the GL-iNet repository listed:
| qcom,pcie@80000 {
| compatible = "qcom,msm_pcie";
| reg = <0x80000 0x2000>,
| <0x99000 0x800>,
| <0x40000000 0xf1d>,
| <0x40000f20 0xa8>,
| <0x40100000 0x1000>,
| <0x40200000 0x100000>,
| <0x40300000 0xd00000>;
| reg-names = "parf", "phy", "dm_core", "elbi",
| "conf", "io", "bars";
Matching the reg-names with the listed reg leads to
<0xd00000> as the size for the "bars".
BugLink: https://www.mail-archive.com/openwrt-devel@lists.openwrt.org/msg45212.html
Reported-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch removes the obsolete touchscreen config symbols
and all disables all remaining ones in the generic config.
Generated by running drivers/input/touchscreen/Kconfig
sed -n 's/^config[[:space:]]\(.*\)/# CONFIG_\1 is not set/p' Kconfig |\
sort -d
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds the disabled DRM_RADEON and DRM_AMDGPU
config symbols from the x86' config to the generic target
configs. The existing symbols in the x86' configs are kept
for now, until we know whenever we want to remove such
symbols or not (see Github PR #1831, #1825, #1828).
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Qxwlan E2600AC C1 based on IPQ4019
Specifications:
SOC: Qualcomm IPQ4019
DRAM: 256 MiB
FLASH: 32 MiB Winbond W25Q256
ETH: Qualcomm QCA8075
WLAN: 5G + 5G/2.4G
* 2T2R 2.4/5 GHz
- QCA4019 hw1.0 (SoC)
* 2T2R 5 GHz
- QCA4019 hw1.0 (SoC)
INPUT: Reset buutton
LED: 1x Power ,6 driven by gpio
SERIAL: UART (J5)
UUSB: USB3.0
POWER: 1x DC jack for main power input (9-24 V)
SLOT: Pcie (J25), sim card (J11), SD card (J51)
Flash instruction (using U-Boot CLI and tftp server):
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
server directory.
- Connect PC with one of RJ45 ports, power up the board and press
"enter" key to access U-Boot CLI.
- Use the following command to update the device to OpenWrt: "run lfw".
Flash instruction (using U-Boot web-based recovery):
- Configure PC with static IP 192.168.1.xxx(2-254)/24.
- Connect PC with one of RJ45 ports, press the reset button, power up
the board and keep button pressed for around 6-7 seconds, until LEDs
start flashing.
- Open your browser and enter 192.168.1.1, select "sysupgrade" image
and click the upgrade button.
Qxwlan E2600AC C2 based on IPQ4019
Specifications:
SOC: Qualcomm IPQ4019
DRAM: 256 MiB
NOR: 16 MiB Winbond W25Q128
NAND: 128MiB Micron MT29F1G08ABAEAWP
ETH: Qualcomm QCA8075
WLAN: 5G + 5G/2.4G
* 2T2R 2.4/5 GHz
- QCA4019 hw1.0 (SoC)
* 2T2R 5 GHz
- QCA4019 hw1.0 (SoC)
INPUT: Reset buutton
LED: 1x Power, 6 driven by gpio
SERIAL: UART (J5)
USB: USB3.0
POWER: 1x DC jack for main power input (9-24 V)
SLOT: Pcie (J25), sim card (J11), SD card (J51)
Flash instruction (using U-Boot CLI and tftp server):
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "ubi" filename to "ubi-firmware.bin" and place it in tftp
server directory.
- Connect PC with one of RJ45 ports, power up the board and press
"enter" key to access U-Boot CLI.
- Use the following command to update the device to OpenWrt: "run lfw".
Flash instruction (using U-Boot web-based recovery):
- Configure PC with static IP 192.168.1.xxx(2-254)/24.
- Connect PC with one of RJ45 ports, press the reset button, power up
the board and keep button pressed for around 6-7 seconds, until LEDs
start flashing.
- Open your browser and enter 192.168.1.1, select "ubi" image
and click the upgrade button.
Signed-off-by: 张鹏 <sd20@qxwlan.com>
[ added rng node. whitespace fixes, ported 02_network,
ipq-wifi Makefile, misc dts fixes, trivial message changes ]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds support for the COMFAST CF-E120A v3, an outdoor wireless
CPE with two Ethernet ports and a 802.11an radio.
Specifications:
- AR9344 SoC
- 535/400/267 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, both with PoE-in support
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 5 GHz, up to 25 dBm
- 11 dBi built-in antenna
- POWER/LAN/WAN/WLAN green LEDs
- 4x RSSI LEDs (2x red, 2x green)
- UART (115200 8N1) and GPIO (J9) headers on PCB
Flashing instructions:
The original firmware is based on OpenWrt so a sysupgrade image can be
installed via the stock web GUI. Settings from the original firmware
will be saved and restored on the new one, so a factory reset will be
needed. To do so, once the new firmware is flashed, enter into failsafe
mode by pressing the reset button several times during the boot
process, while while the WAN LED flashes, until it starts flashing
faster. Once in failsafe mode, perform a factory reset as usual.
The U-boot bootloader contains a recovery HTTP server to upload the
firmware. Push the reset button while powering the device on and
keep it pressed for >10 seconds. The recovery page will be at
http://192.168.1.1
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
This patch adds support for the TP-Link TL-WR802N-v4.
https://openwrt.org/toh/tp-link/tl-wr802n
Specification:
- MT7628N (580 MHz)
- 64 MB RAM
- 8 MB FLASH
- 2T2R 2.4 GHz
- 1x 10/100 Mbps Ethernet
- 1x LED
Flash instruction:
The only way to flash the image in TL-WR802N v4 is to use
tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.0.225/24 and tftp server.
2. Rename "openwrt-ramips-mt76x8-tplink_tl-wr802n-v4-squashfs-tftp-recovery.bin"
to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with the LAN port, press the reset button, power up
the router and keep button pressed for around 10 seconds, until
device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.
Signed-off-by: Marcel Jost <majo@icutech.ch>
* assign pinmux groups to gpio function for LEDs/buttons
* rename flash node to be more generic in line with other device nodes
* remove useless/incorrect eeprom property from wmac node
* correct base mac address for embedded switch
Signed-off-by: Thomas Vincent-Cross <me@tvc.id.au>
The TP-Link WDR3600 shares the same machine-code in the ar71xx target,
thus expecting "tl-wdr4300" not "tl-wdr3600" in the support-list
metadata to allow non-forced sysupgrades from ar71xx to ath79.
With this, it is possible to flash a WDR4300 image on the WDR3600. It
is no problem however, as the only difference is the 5GHz WiFi chip
which has 3SS instead of 2SS. Both work with either image.
Signed-off-by: David Bauer <mail@david-bauer.net>
This adds the support-list entry the AVM FRITZ!Box 4020 expects in the
ar71xx target to allow non-forced sysupgrades from ar71xx to ath79.
Signed-off-by: David Bauer <mail@david-bauer.net>
remove USB as this is no LED but power control
rename WiFi LED with correct color red (like in stock firmware)
set middle LED to be used for LAN link/activity
Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de>
ALFA Network AP120C-AC is a dual-band ceiling AP, based on Qualcomm
IPQ4018 + QCA8075 platform.
Specification:
- Qualcomm IPQ4018 (717 MHz)
- 256 MB of RAM (DDR3)
- 16 MB (SPI NOR) + 128 MB (SPI NAND) of flash
- 2x Gbps Ethernet, with 802.3af PoE support in one port
- 2T2R 2.4/5 GHz (IPQ4018), with ext. FEMs (QFE1952, QFE1922)
- 3x U.FL connectors
- 1x 1.8 dBi (Bluetooth) and 2x 3/5 dBi dual-band (Wi-Fi) antennas
- Atmel/Microchip AT97SC3205T TPM module (I2C bus)
- TI CC2540 Bluetooth LE module (USB 2.0 bus)
- 4x LED (all driven by GPIO)
- 1x button (reset)
- 1x USB 2.0 (optional, not installed in indoor version)
- DC jack for main power input (12 V)
- UART header available on PCB (2.0 mm pitch)
Flash instruction:
1. This board uses dual-image feature (128 MB NAND is divided into two
64 MB partitions: 'rootfs1' and 'rootfs2').
2. Before update, make sure your device is running firmware no older
than v1.1 (previous versions have incompatible U-Boot).
3. Use 'factory' image in vendor GUI or for sysupgrade tool, without
preserving settings.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Without a proper SPI NAND support (SPI NAND framework is available in
kernel >= 4.19) the only way to make such flash working is to include
it in raw/parallel NAND subsystem support and combine with mt29f staging
driver. Obviously, this approach isn't going to be accepted by upstream
(similar support for Winbond W25N01GV was rejected).
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
The addition of kmod-input-touchscreen-ads7846 enabled
INPUT_TOUCHSCREEN, which exposes several other symbols on various
targets. Add those symbols to the generic kernel configs to fix build.
Fixes: 77a54bbf13 ("kernel: add kmod-input-touchscreen-ads7846")
Reported-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This module adds support for ADS7846 based touchscreens used in devices
like the WaveShare 3.5" and 4" LCD displays designed for Raspberry Pi.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This module adds support for small TFT LCD display modules. While this
module also exists in the 4.9 kernel, we are not going to support this
kernel in the next major release, so don't make it available for 4.9.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
According to /arch/mips/include/asm/mach-ath79/ar71xx_regs.h
the size of wmac register range for qca953x is only 0x20000.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This makes OpenWrt build an Ext2+Ext4 partitioned image
for the D-Link DNS-313 with two blank partitions, a boot
partition on /dev/sda3 and a rootfs partition on
/dev/sda4.
This uses the methods already used in apm821xx including
the tricks to convert the generated Ext2 filesystem
partition to version 1 so that the firmware bootloader
will properly recognize it.
We patch a bit around the build files to make sure we
get the rootfs size set and that genext2fs is properly
built.
Tested on the D-Link DNS-313.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[Fixing and tricksing]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reading and writing to and from flash storage is slow and currently,
the ath10kcal_extract() scripts are even more at an disadvantage
because they use a block size of 1 to be able skip.
This patch reworks the extraction scripts to be much faster and
efficient by reading and writing the calibration data in possibly
one big block.
before: (Tested on a RT-AC58U, which has SPI-NAND).
# time dd if=/dev/ubi0_1 of=/lib/firmware/... bs=1 skip=4096 count=12064
12064+0 records in
12064+0 records out
real 0m 0.28s
user 0m 0.02s
sys 0m 0.24s
after:
# time dd if=/dev/ubi0_1 of=/lib/firmware/... bs=12064 skip=4096 count=1 iflag=skip_bytes
1+0 records in
1+0 records out
real 0m 0.01s
user 0m 0.00s
sys 0m 0.00s
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
DRM packages break modules compilation for sunxi target,
cortexa7 and cortexa8 subtargets.
This patch add missing symbol to generic config.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This is required for running armvirt_32 on QEMU 3.0 [1], otherwise the
kernel will emit the following complaint and virtio-net-pci devices will
fail to be initialized
[ 1.124214] OF: PCI: host bridge /pcie@10000000 ranges:
[ 1.125093] OF: PCI: IO 0x3eff0000..0x3effffff -> 0x00000000
[ 1.125942] OF: PCI: MEM 0x10000000..0x3efeffff -> 0x10000000
[ 1.126403] OF: PCI: MEM 0x8000000000..0xffffffffff -> 0x8000000000
[ 1.127748] pci-host-generic 4010000000.pcie: can't claim ECAM area [mem 0x10000000-0x1fffffff]: address conflict with /pcie@10000000 [mem 0x10000000-0x3efeffff]
[ 1.129752] pci-host-generic: probe of 4010000000.pcie failed with error -16
Running QEMU with "-M virt,highmem=off" is an option, but "highmem" was only
introduced as a default on flag since QEMU 2.5.0 and QEMU will fail and quit on
encounter of unknown flags
[1] Armv7 guest fails to boot with qemu-3.0.0-1,
https://bugzilla.redhat.com/show_bug.cgi?id=1633328#c5
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
The diff was genereated by running the following command without
actually changing any kernel config options
make kernel_menuconfig CONFIG_TARGET=subtarget
Here are some initial findings on the change
- CONFIG_ARCH_OPTIONAL_KERNEL_RWX is now arch default
- CONFIG_ARM_GIC_V3_ITS is selected by CONFIG_ARCH_VIRT
- CONFIG_CPU_SPECTRE is select by CONFIG_CPU_V7
- CONFIG_TIMER_OF is now a arch default
- CONFIG_TIMER_PROBE is select by CONFIG_TIMER_OF
The following options should probably be moved to generic config
- CONFIG_MIGRATION is a default on option
- CONFIG_TREE_SRCU is a default on option for !PREEMPT && SMP system
- CONFIG_RCU_NEED_SEGCBLIST
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Add patches for 4.19
Drop patch 200-disable-tso, as the packet corruption was fixed in
kernel commit 3b89624ab54b9dc2d92fc08ce2670e5f19ad8ec8
Restructure the DTS for Marvell switch in 104-ea3500 and 105-ea4500
to fix DTC warning.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
builtin driver can't access the /lib/firmware while booting,
module driver will be able to read and load the firmware files
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
CONFIG_USB_IMX21_HCD should be handled in generic config and
module package. So moved it into generic config.
This also fixed build issue (kernel config question) of layerscape
armv8_32b since it also used ARCH_MXC.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[Deactivate CONFIG_USB_IMX21_HCD also for kernel 4.19]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport A64 unstable timer patches from linux 5.1
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
[Split the single patch into the two original patches]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It was previously added in 546fced, which was part of "intel-microcode:
load as early as possible" series.
Unfortunately the conditionals added to GRUB config caused error on boot,
because on sysupgrade, bootloader is not updated and is left with old
features/modules. Since this module is needed for early microcode load
and transition to this needs to be done step by step, enable the test
module now, so that every newly created image has it already embedded.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
VBoxManage is not used and the image is created with proper permisions:
0f5d0f6 image: use internal qemu-img for vmdk and vdi images drop host
dependencies on qemu-utils and VirtualBox
Unreachable config symbols:
9e0759e x86: merge all geode based subtargets into one
No need to define those symbols since x86_64 is subtarget of x86:
196fb76 x86: make x86_64 a subtarget instead of a standalone target
Unreachable config symbols, so remove GRUB_ROOT:
371b382 x86: remove the xen_domu subtarget
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Looks like C60 v2 needs the MAC address to be calculated
manually, while the C60 v1 gets it correctly without manual
interference.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit fixes the script that sets the MAC address of the LAN
switch. The LAN MAC address should be the WAN MAC address plus one.
Without this patch the WAN and the LAN interface will use the same
MAC address and an error will be generated.
With this patch all interfaces will have a different MAC address,
consecutive in the following order: WAN, LAN, radio0 and radio1.
Signed-off-by: Oever González <notengobattery@gmail.com>
(original text here: https://patchwork.kernel.org/patch/8686761/)
On some SOCs PORTS_IMPL register value is never programmed by the BIOS
and left at zero value. Which means that no sata ports are avaiable for
software. AHCI driver used to cope up with this by fabricating the
port_map if the PORTS_IMPL register is read zero, but recent patch
broke this workaround as zero value was valid for nvme disks.
This patch adds ports-implemented dt bindings as workaround for this issue
in a way that DT can dictate the port_map incase where the SOCs does not
program it already.
This patch is equal to commits:
67f8425d0ee1 ("ipq8064: dts: force AP148 SATA port mapping")
2e7a2c91019c ("ARM: dts: qcom: Move common nodes to ipq8064-v.1.0.dtsi")
in the upstream linux kernel.
Signed-off-by: Roman Glova <roman_glova@epam.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[added upstream commits, reorg' commit message]
I-O DATA WN-AC1600DGR is a 2.4/5 GHz band 11ac router, based on
Qualcomm Atheros QCA9557.
Specification:
- SoC: Qualcomm Atheros QCA9557
- RAM: 128 MB
- Flash: 16 MB
- WLAN: 2.4/5 GHz
- 2.4 GHz: 2T2R (SoC internal)
- 5 GHz: 3T3R (QCA9880)
- Ethernet: 5x 10/100/1000 Mbps
- Switch: QCA8337N
- LED/key: 6x/6x(4x buttons, 1x slide switch)
- UART: through-hole on PCB
- Vcc, GND, TX, RX from ethernet port side
- 115200n8
Flash instruction using factory image:
1. Connect the computer to the LAN port of WN-AC1600DGR
2. Connect power cable to WN-AC1600DGR and turn on it
3. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing
Alternative flash instruction using initramfs image:
1. Prepare a computer and TFTP server software with the IP address
"192.168.99.8" and renamed OpenWrt initramfs image
"uImageWN-AC1600DGR"
2. Connect between WN-AC1600DGR and the computer with UART
3. Connect power cable to WN-AC1600DGR, press "4" on the serial
console and enter the U-Boot console
4. execute "tftpboot" command on the console and download initramfs
image from the TFTP server
5. execute "bootm" command and boot OpenWrt
6. On initramfs image, download the sysupgrade image to the device
and perform sysupgrade with it
7. Wait ~150 seconds to complete flashing
This commit also removes unnecessary "qca,no-eeprom" property from
the ath10k wifi node.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Tested with a dual pci QCA9558 board (LibreRouter v1) in three
configurations: enabling pcie0 only, pcie1 only and both enabled.
Signed-off-by: Santiago Piccinini <spiccinini@altermundi.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed ML notice]
Datasheet states that both PCI ranges are of 0x2000000 size:
0x1000_0000-0x11FF_FFF and 0x1200_0000-0x13FF_0000.
Signed-off-by: Santiago Piccinini <spiccinini@altermundi.net>
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed ML notice]
SoC: Qualcomm IPQ4019 (Dakota) 717 MHz, 4 cores
RAM: 256 MiB (Nanya NT5CC128M16IP-DI)
FLASH: 128 MiB (Macronix NAND)
WiFi0: Qualcomm IPQ4019 b/g/n 2x2
WiFi1: Qualcomm IPQ4019 a/n/ac 2x2
WiFi2: Qualcomm Atheros QCA9886 a/n/ac
BT: Atheros AR3012
IN: WPS Button, Reset Button
OUT: RGB-LED via TI LP5523 9-channel Controller
UART: Front of Device - 115200 N-8
Pinout 3.3v - RX - TX - GND (Square is VCC)
Installation:
1. Transfer OpenWRT-initramfs image to the device via SSH to /tmp.
Login credentials are identical to the Web UI.
2. Login to the device via SSH.
3. Flash the initramfs image using
> mtd-write -d linux -i openwrt-image-file
4. Power-cycle the device and wait for OpenWRT to boot.
5. From there flash the OpenWRT-sysupgrade image.
Ethernet-Ports: Although labeled identically, the port next to
the power socket is the LAN port and the other one is WAN. This
is the same behavior as in the stock firmware.
Signed-off-by: Marius Genheimer <mail@f0wl.cc>
[Dropped setup_mac 02_network in favour of 05_set_iface_mac_ipq40xx.sh,
reorderd 02_network entries, added board.bin WA for the QCA9886 from ath79,
minor dts touchup, added rng to 4.19 dts]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Robert Marko made a big effort to enable the rng on all
ipq40xx for 4.19, so let's continue the quest.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This factory binary i supposed to actually be unzipped and
untarred by the user as part of the installation process
(this NAS boots from harddisk), so name it "bootpart.tar.gz"
and not "factory.bin" so it is helpful for users.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
OCEDO Panda was added in b368373f, but only for
4.14 config. This patch fix 4.19 build for generic
and p2020 subtarget.
Signed-off-by: Pawel Dembicki <p.dembicki@wb.com.pl>
Buffalo WHR-G300N has a LED for power status indication, but it is not
connected to the GPIO and cannot be controlled by the kernel. So,
WHR-G300N uses "ROUTER" LED as the system status LED instead.
This commit changes it to use "DIAG" LED insted of "ROUTER" like
WHR-G301N in ath79 target.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
The R6120 has no 5GHz WLAN LED, the assigned GPIO in fact controls
the WAN LED.
Renames the LED accordingly in the device-tree.
Removes the 5GHz WLAN LED trigger.
Adds the correct WAN port LED trigger.
----
Currently, the MAC address for the Netgear R6120 is read from the NVRAM
partition. The offset for the MAC address however is not consistent
across devices or firmware versions.
Switch to using the factory partition like all other Netgear devices do.
----
The LAN ports of the R6120 are labled in reverse on the casing.
Adjust LuCI switchport numbering accordingly.
----
The WiFi eeprom offsets for the R6120 are currently wrong (5GHz offset
is bigger than the partition itself).
Fixes poor performance on 2.4 and 5 GHz.
Signed-off-by: David Bauer <mail@david-bauer.net>
The switch ports are seen one to one on the case.
Also remove unneeded secondary port numbers in this
case statement.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Change the ledtrig for LAN from netdev to switch.
Although eth1 comes out of the device at a single port,
this port is a switch-port and therefore the LED
must be triggered by that.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Enable the built-in BPF JIT compiler for all 4.9, 4.14 and 4.19 kernels,
which should speed up cBPF and eBPF-based packet filtering (tc, iptables)
and packet sniffing (libpcap, tcpdump, fwknopd, etc).
This has minimal kernel size impact, increasing the size of uImage-lzma
(normally ~2 MB on mips_24kc or mips64el_mips64) by 5 KB for the MIPS32
arch cBPF JIT and by 9 KB for the MIPS64 arch eBPF JIT, on kernel 4.14.
With JIT enabled (cBPF only), the standard BPF test module (test_bpf.ko)
running on a DIR-835 (mips_24kc) used 33 CPU seconds, but 68 without JIT.
This change aligns with the notion of OpenWRT as the network go-to swiss
army knife for packet handling, especially on CPU-constrained platforms.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Hardware
--------
CPU: Qualcomm Atheros QCA9561
RAM: 64M DDR2
FLASH: 16M SPI-NOR
ETH: 1x WAN - 2x LAN
WiFi: QCA9561 3T3R
BTN: 1x Reset - 1x WPS
LED: 1x Blue - 1x Red - 1x Yellow
UART: TX - GND - RX - VCC (From ethernet port)
115200n8 - 3.3V
Installation
------------
1. Connect to the device via UART.
2. Interrupt the U-Boot on power-on by pressing enter when prompted.
3. Connect you computer to one of the routers LAN ports.
Assign yourself the IP 192.168.31.10/24.
Copy the OpenWRT initramfs image to a tftp server root directory.
Rename the image to 'x4q.bin'.
4. Load the initramfs image to the router by executing following command
in U-Boot. The image will boot afterwards.
> tftpboot 0x81000000 x4q.bin; bootm
5. SCP the sysupgrade-image into '/tmp'.
Remember to assign yourself an IP in 192.168.1.0/24 for this step!
6. Install OpenWRT permanently by executing
> sysupgrade -n /tmp/<OpenWRT-sysupgrade-image>
Signed-off-by: David Bauer <mail@david-bauer.net>
Commit 7ebbbda293 ("ar71xx: ubnt-(xm,xw): fix LED RSSI indication")
adds support for using the RSSI strenght via LEDS.
The rssileds package addition got lost during altering the patch.
Add it again to fix this.
Fixes: 7ebbbda293 ("ar71xx: ubnt-(xm,xw): fix LED RSSI indication")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This patch uses nfct_help() to detect whether an established connection
needs conntrack helper instead of using test_bit(IPS_HELPER_BIT,
&ct->status).
The reason for this modification is that IPS_HELPER_BIT is only set when
the conntrack helper is attached by explicit CT target.
However, in the case that a device enables conntrack helper via the other
ways (e.g., command "echo 1 > /proc/sys/net/netfilter/nf_conntrack_helper")
, the status of IPS_HELPER_BIT will not present any change. That means the
IPS_HELPER_BIT might lose the checking ability in the context.
Signed-off-by: HsiuWen Yen <y.hsiuwen@gmail.com>
When mapping for RSSI LEDs was defined for interface wlan0 on
Ubiquiti XM and XW family, it missed connection to actual interface.
Therefore create the mapping to interface, so RSSI LEDs work without
additional configuration, after starting rssileds service.
Also add the required package for this.
While at that, remove coefficients needed for PWM LEDs, as XM and XW
boards do not support PWM LEDs.
Tested-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[Squashed commits + remove custom device_packages + slighty rewrite the commit msg]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Some hAP lite routers aren't detected because
/proc/cpuinfo shows "RouterBOARD RB941-2nD"
instead of "RouterBOARD 941-2nD".
Fix that.
Signed-off-by: Julien Rabier <taziden@flexiden.org>
[Alter string to include all flavours + slight rewrite of commit msg]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
While preparing 4.19 for imx6 and test building it with
CONFIG_ALL_KMODS=y with verbose mode enabled, I was asked by kernel
config about few missing symbols/modules
Let's add them to the generic config.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[slight rewrite of commit log]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
On ath79 and UBNT Bullet M XW (ar9342) I was experiencing weird issues during
network setup[1] which I was able to reproduce easily with following commands:
uci set network.lan.ipaddr='192.168.1.20'
uci commit network
ifup lan
Which resulted after some time in:
...
WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:461 dev_watchdog+0x16c/0x280
NETDEV WATCHDOG: eth0 (ag71xx): transmit queue 0 timed out
...
Sometimes I wasn't able to use networking anymore, sometimes it was enough to
just ifdown/ifup lan and network was backup. On ar71xx it was all working just
fine.
I've found out, that it was happening because ag71xx_poll() wasn't called, thus
the TX queue wasn't emptied. The ag71xx_poll() is being called from napi
hrtimer, which is enabled by napi_schedule() in ar71xx_interrupt(), but since
no interrupts were ever fired again after ag71xx_stop() was called, it was
always leading to tx queue timeouts:
*** ag71xx_hard_start_xmit()
eth0: packet injected into TX queue
eth0: raw intr=00000001 TXPS POLL
eth0: enable polling mode
eth0: processing TX ring, flush=no
eth0: disable polling mode, rx=1, tx=1,limit=32
( `ifup lan done here` )
*** ag71xx_stop()
*** ag71xx_open()
*** ag71xx_hw_enable()
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
*** ag71xx_hard_start_xmit()
eth0: packet injected into TX queue
*** ag71xx_hard_start_xmit()
eth0: packet injected into TX queue
...
WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:320 dev_watchdog+0x164/0x274
So I've looked at ag71xx_stop() in ar71xx, added the missing bits to ath79 and
fixed this issue.
1. https://github.com/openwrt/openwrt/pull/1635#issuecomment-448638246
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[move ag->link before ag71xx_hw_disable to retain ordering as original]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Restoring the bootloader config before rebooting fails:
tar: invalid tar magic
Add the -z option to the tar command to fix this.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
TP-Link Archer C7 v4 is a dual-band AC1750 router, based on the
Qualcomm/Atheros QCA9561 SoC + QCA9880.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB
Flash instruction:
1. Upload openwrt-ath79-generic-tplink_archer-c7-v4-squashfs-factory.bin
via Web interface
Flash instruction using TFTP recovery:
1. Set PC to fixed ip address 192.168.0.66
2. Download openwrt-ath79-generic-tplink_archer-c7-v4-squashfs-factory.bin
and rename it to ArcherC7v4_tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
This option was a spi nor hack which is dropped in commit
bcf4a5f474 ("ramips: remove chunked-io patch and set spi->max_transfer_size instead")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [edit message]
The WeVo 11AC NAS has a MT7612E 802.11ac chip on the PCB.
Signed-off-by: Ju Se Hoon <joosahoon@gmail.com>
[renamed author from Albis-dev to real name, editted commit message]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch fixes the ASUS' RT-AC58U port order by
unifying the configuration with the NBG6617.
Reported-by: Roberto Socrates (rtac58u-user on the forum)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch splits the big board case switch in 02_network in
two functions ipq40xx_setup_interfaces() and ipq40xx_setup_macs()
just like ath79 and ramips do.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Building ar71xx currently fails with:
In file included from ./include/linux/ipv6.h:5,
from ./include/net/ipv6.h:16,
from ./include/net/inetpeer.h:16,
from ./include/net/ip_fib.h:24,
from ./include/net/switchdev.h:17,
from ./include/net/dsa.h:23,
from arch/mips/ath79/dev-dsa.h:15,
from arch/mips/ath79/dev-dsa.c:17:
./include/uapi/linux/ipv6.h:107:1: error: alignment 1 of 'struct ipv6_destopt_hao' is less than 2 [-Werror=packed-not-aligned]
} __attribute__((packed));
Address this issue by correcting the alignment of the struct packing
pragma accordingly.
Fixes: FS#1805
Reported-by: Pascal Ernster <git@hardfalcon.net>
[reword subject, rewrap commit message]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The correct MAC address for this device is lan_mac +1, there is no
need to set lan_mac so use base_mac variable instead lan_mac.
Based on this PR for ath79:
https://github.com/openwrt/openwrt/pull/1726
Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
[fix alphabetical ordering, reword subject]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Kernel 4.14.96 got the new configuration option
CIFS_ALLOW_INSECURE_LEGACY which allows to deactivate support for old
and insecure SMB versions like 1.0 and 2.0. Still allow these old SMB
version and fix build problems which occurred because this option was
not defined.
This was found by build bot.
Fixes: 3662157d8b ("kernel: bump 4.14 to 4.14.96")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
upstream commit 802b7c06adc7 ("ARM: cns3xxx: Convert PCI to use generic config accessors")
reimplemented cns3xxx_pci_read_config() using pci_generic_config_read32(),
which preserved the property of only doing 32-bit reads.
It also replaced cns3xxx_pci_write_config() with pci_generic_config_write(),
so it changed writes from always being 32 bits to being the actual size,
which works just fine.
Due to:
- The documentation does not mention that only 32 bit access is allowed.
- Writes are already executed using the actual size
- Extensive testing shows that 8b, 16b and 32b reads work as intended
It makes perfectly sense to also swap 32 bit reading in favor of actual size.
also backport this patch to kernel 4.19
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
There are more regmap dependencies missing in the brcm2708 target.
Fixes: fd5c168701 ("kernel: Build: Split kmod-regmap")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add missing pin controls for the Observa VH4032N router.
This fixes the wifi radio and ethernet LAN LEDs.
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
- use the blue LED for power, since the red LED is already used by
CFE in emergency mode.
- use the correct code for the wlan button
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
kmod-sound-soc-3dlab-nano-player was in the global kernel menu before,
add the dependency to sound to move it to the correct category.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Two regmap dependencies were wrong, this patch fixes them.
This was detected by the build bots.
Fixes: fd5c168701 ("kernel: Build: Split kmod-regmap")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In the upstream netdev led trigger the one mode file was replaced by 3
files named rx, tx and link. Fix the netdev trigger configuration code
to use the modified API.
This fix is based on 201058b35c ("base-files: Fix netdev led trigger")
Fixes: aa3b6a08c5 ("kernel: Replace ledtrig-netdev with upstream backport")
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Add support for Silergy SY8106A voltage regulator which is
needed for cpufreq support on boards such as Orange Pi PC
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
[Remove CONFIG_REGULATOR_SY8106A from cortexa7]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Drop customizations in:
508-arm64-dts-armada-3720-espressobin-wire-up-spi-flash.patch
and move them to separate patch, with broader explanation.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This symbol is enabled in all subtargets, move it to common kernel
config.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Acked-by: Rosen Penev <rosenp@gmail.com>
This reduces the needed modifications to the mainline Linux kernel and
also makes the regmap package work with an out of tree kernel which
does not have these modifications.
The regmap-core is only added when it is really build as a module.
The regmap-core is normally bool so it cannot be built as a module in an
unmodified kernel. When it is selected by on other kernel module it will
always be selected as build in and it also does not show up in
$(LINUX_DIR)/modules.builtin as it is not supposed to be a kernel module.
When it is not in $(LINUX_DIR)/modules.builtin the build system expects
it to be built as a .ko file.
Just check if the module is really there and only add it in that case.
This splits the regmap package into multiple packages, one for each bus type.
This way only the bus maps which are really needed have to be added.
This also splits the I2C, SPI and MMIO regmap into separate packages to not
require all these subsystems to build them, on an unmodified upstream kernel
this also causes problems in some situations.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
Some of sunxi devices have onboard SPI flash.
Enable SPI NOR support and MTD fit split in kernel config.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Hardware
--------
CPU: Qualcomm Atheros QCA9558
RAM: 128M DDR2
FLASH: 16MiB
ETH: 1x Atheros AR8035 (PoE in)
1x Atheros AR8033
WiFi2: QCA9558 3T3R (SiGE SE2565T 2.4 GHz power amp x3)
WiFi5: QCA9880 3T3R (Skyworks 5003L1 5 GHz power amp x3)
BTN: 1x Reset
1x WPS
1x USB eject
LED: 1x LED blue
1x LED red
BEEP: 1x GPIO attached piezo beeper
UART: 3.3V GND TX RX (115200-N-8) (3.3V is pin closest to rear ports)
Dupont 4 pin header
Rear RJ45 serial port non-functional
USB: 1x v2.0
Installation
------------
Make sure you set a password for the root user as prompted on first
setup!
1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password previously set in the web interface.
2. Install OpenWRT with
> sysupgrade -n -F /tmp/<openwrt-image-name>
Signed-off-by: Django Armstrong <iamdjango@hotmail.com>
It's no longer needed as all mt7621 devices use DT binding (supported by
upstream mtd code) for specifying "firmware" part format explicitly.
Signed-off-by: Mathias Kresin <dev@kresin.me>
It results in calling the right MTD parser directly instead of trying
them one by one.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
[use the lzma splitter for the AR670W]
Signed-off-by: Mathias Kresin <dev@kresin.me>
This is the remainder of kernel patches for the v4.19
kernel. A whole slew of the previous patch stack is now
upstream, so this mainly contains the stuff that was
added upstream between v4.19 and v5.0-rc1, and then
the USB FOTG201 patches from Hans.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds support for the TP-Link Archer C50 v4.
It uses the same hardware as the v3 variant, sharing the same FCC-ID.
CPU: MediaTek MT7628 (580MHz)
RAM: 64M DDR2
FLASH: 8M SPI
WiFi: 2.4GHz 2x2 MT7628 b/g/n integrated
WiFI: 5GHz 2x2 MT7612 a/n/ac
ETH: 1x WAN 4x LAN
LED: Power, WiFi2, WiFi5, LAN, WAN, WPS
BTN: WPS/WiFi, RESET
UART: Near ETH ports, 115200 8n1, TP-Link pinout
Create Factory image
--------------------
As all installation methods require a U-Boot to be integrated into the
Image (and we do not ship one with the image) we are not able to create
an image in the OpenWRT build-process.
Download a TP-Link image from their Wesite and a OpenWRT sysupgrade
image for the device and build yourself a factory image like following:
TP-Link image: tpl.bin
OpenWRT sysupgrade image: owrt.bin
> dd if=tpl.bin of=boot.bin bs=131584 count=1
> cat owrt.bin >> boot.bin
Installing via Web-UI
---------------------
Upload the boot.bin via TP-Links firmware upgrade tool in the
web-interface.
Installing via Recovery
-----------------------
Activate Web-Recovery by beginning the upgrade Process with a
Firmware-Image from TP-Link. After starting the Firmware Upgrade,
wait ~3 seconds (When update status is switching to 0%), then
disconnect the power supply from the device. Upgrade flag (which
activates Web-Recovery) is written before the OS-image is touched and
removed after write is succesfull, so this procedure should be safe.
Plug the power back in. It will come up in Recovery-Mode on 192.168.0.1.
When active, all LEDs but the WPS LED are off.
Remeber to assign yourself a static IP-address as DHCP is not active in
this mode.
The boot.bin can now be uploaded and flashed using the web-recovery.
Installing via TFTP
-------------------
Prepare an image like following (Filenames from factory image steps
apply here)
> dd if=/dev/zero of=tp_recovery.bin bs=196608 count=1
> dd if=tpl.bin of=tmp.bin bs=131584 count=1
> dd if=tmp.bin of=boot.bin bs=512 skip=1
> cat boot.bin >> tp_recovery.bin
> cat owrt.bin >> tp_recovery.bin
Place tp_recovery.bin in root directory of TFTP server and listen on
192.168.0.66/24.
Connect router LAN ports with your computer and power up the router
while pressing the reset button. The router will download the image via
tftp and after ~1 Minute reboot into OpenWRT.
U-Boot CLI
----------
U-Boot CLI can be activated by holding down '4' on bootup.
Dual U-Boot
-----------
This is the first TP-Link MediaTek device to feature a split-uboot
design. The first (factory-uboot) provides recovery via TFTP and HTTP,
jumping straight into the second (firmware-uboot) if no recovery needs
to be performed. The firmware-uboot unpacks and executed the kernel.
Web-Recovery
------------
TP-Link integrated a new Web-Recovery like the one on the Archer C7v4 /
TL-WR1043v5. Stock-firmware sets a flag in the "romfile" partition
before beginning to write and removes it afterwards. If the router boots
with this flag set, bootloader will automatically start Web-recovery and
listens on 192.168.0.1. This way, the vendor-firmware or an OpenWRT
factory image can be written.
By doing the same while performing sysupgrade, we can take advantage of
the Web-recovery in OpenWRT.
It is important to note that Web-Recovery is only based on this flag. It
can't detect e.g. a crashing kernel or other means. Once activated it
won't boot the OS before a recovery action (either via TFTP or HTTP) is
performed. This recovery-mode is indicated by an illuminated WPS-LED on
boot.
Signed-off-by: David Bauer <mail@david-bauer.net>
Specifications:
SOC: Qualcomm IPQ4018
RAM: 256 MiB Samsung K4B2G1646F-BYK0
FLASH1: MX25L1605D 2 MB
FLASH2: Winbond W25N01GV 128Mb
ETH: Qualcomm QCA8075
WLAN0: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN1: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2
INPUT: WPS, Reset
LED: Status - Green
SERIAL: Header at J19, Beneath DC Power Jack
1-VCC ; 2-TX ; 3-RX; 4-GND;
Serial 115200-8-N-1.
Tested and working:
- USB (requires extra packages)
- LAN Ethernet (Correct MAC-address)
- WAN Ethernet (Correct MAC-address)
- 2.4 GHz WiFi (Correct MAC-address)
- 5 GHz WiFi (Correct MAC-address)
- Factory installation from Web UI
- OpenWRT sysupgrade
- LED
- Reset Button
Need Testing:
- WPS button
Install via Web UI:
- Attach to a LAN port on the router.
- Connect to the Linksys Smart WiFi Page (default 192.168.1.1) and login
- Select the connectivity tab on the left
- In the manual update box on the right
- Select browse, and browse to
openwrt-ipq40xx-linksys_ea6350v3-squashfs-factory.bin
- Click update.
- Read and accept the warning
- The router LED will start blinking. When the router LED goes solid, you
can now navigate to 192.168.1.1 to your new OpenWrt installation.
Sysupgrade:
- Flash the sysupgrade image as usual. Please: try to do a reset everytime
you can (doing it with LuCI is easy and can be done in the same step).
Recovery (Automatic):
- If the device fails to boot after install or upgrade, whilst the unit is
turned on:
1 - Wait 15 seconds
2 - Switch Off and Wait 10 seconds
3 - Switch on
4 - Repeat steps 1 to 3, 3 times then go to 5.
5 - U-boot will have now erased the failed update and switched back to the
last working firmware - you should be able to access your router on
LAN.
Recovery (Manual):
- The steps for manual recovery are the same as the generic u-boot tftp
client method.
Back To Stock:
- Use the generic recovery using the tftp client method to flash the
"civic.img". Also you can strip-and-pad the original image and use
the generic "mtd" method by flashing over the "kernel" partition.
* Just be careful to flash in the partition that the device is currently
booted.
Signed-off-by: Ryan Pannell <ryan@osukl.com>
Signed-off-by: Oever González <notengobattery@gmail.com>
[minor edits, removed second compatible of nand, added dtb entry to 4.19]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Patch picked from commit 82618062cf
This enables 4B opcodes for MX25L25635F, to fix the reboot crash
issue (FS#1120) At least 3 devices are using this flash
- GeHua GHL-R-001
- Youku YK1
- Newifi D1
Now the MX25L25635F can be correctly detected without breaking MX25L25635E
[ 3.034324] spi-mt7621 1e000b00.spi: sys_freq: 220000000
[ 3.045962] m25p80 spi0.0: mx25l25635f (32768 Kbytes)
[ 3.056098] 4 fixed-partitions partitions found on MTD device spi0.0
[ 3.068748] Creating 4 MTD partitions on "spi0.0":
Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [added deprecation notice]
CPU: FSL P1020 (2x 800MHz E500 PPC)
RAM: 1GB DDR3
FLASH: 256MiB NAND
WiFi: 2x Atheros AR9382 2x2:2 abgn
ETH: 2x BCM54616S - 1x BCM53128 8-port switch
LED: 5x LEDs (Power, WiFi1, WiFi2, N/D, SYS)
BTN: 1x RESET
Installation
------------
1. Download initrams kernel image, dtb binary and sysupgrade image.
2. Place initramfs kernel into tftp root directory. Rename to
"panda-uimage-factory".
3. Place dtb binary into tftp root directory. Rename to "panda.fdt".
4. Start tftp server on 192.168.100.8/24.
5. Power up the device with the reset button pressed. It will download
the initrams and dtb via tftp and boot into OpenWRT in RAM.
6. SSH into the device and remove the factory partitions.
> ubirmvol /dev/ubi0 --name=kernel1
> ubirmvol /dev/ubi0 --name=rootfs1
> ubirmvol /dev/ubi0 --name=devicetree1
You will have around 60 MiB of free space with that.
You can also delete "kernel2", "devicetree2", "rootfs2" and "storage"
respectively in case you do not want to go back to the vendor firmware.
7. Modify the U-Boot bootcmd to allow for booting OpenWRT
> fw_setenv bootcmd_owrt "ubi part ubi && ubi read 0x1000000 kernel
&& bootm 0x1000000"
> fw_setenv bootargs_owrt "setenv bootargs console=ttyS0,115200
ubi.mtd=3,2048"
> fw_setenv bootcmd "run bootargs_owrt; run bootcmd_owrt"
8. Transfer the sysupgrade image via scp into the /tmp directory.
9. Upgrade the device
> sysupgrade -n /tmp/<imagename>
Signed-off-by: David Bauer <mail@david-bauer.net>
This commit removes the target-specific diag.sh script. This way, the
generic one is used for the target, which uses DT-aliases to specify the
LEDs used.
This way, we are also able to use different LEDs to indicate different
states. We use green status LEDs for indicating boot and a running
system. Where possible, the red status LED is used to indicate failsafe
mode and a running upgrade.
Signed-off-by: David Bauer <mail@david-bauer.net>
The unit address should be wifi@1,0 since the device is located
at 0000:01:00.0.
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
With 6409b159e8 ("gemini: switch to 4.14") the EOF marker were dropped
from the rootfs images. Without the marker the rootfs_data partition
can't be created and it isn't possible to permanently store any
configuration changes.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Replace the data placerholder in ImageInfo-itian_sq201 in a reproducible
way.
The code for the replace was accidentality dropped in 5bac623895
("gemini: unify and fix ib-nas4220b and sq201 image creation")
Signed-off-by: Mathias Kresin <dev@kresin.me>
Support for the Teltonika RUT1xx was added with the switch to kernel
4.4. Hidding such changes in a kernel switch commit is the wrong way and
the support for the Teltonika RUT1xx is pretty much incomplete.
Signed-off-by: Mathias Kresin <dev@kresin.me>
They were dropped with 6409b159e8 ("gemini: switch to 4.14") without
any explaination.
The image generation is disabled for now as it would break the build for
the target. The mkfwimage2 call need to be adjusted to reflect the real
size of kernel and rootfs. Nevertheless, add the required code to give
interested parties a chance to fix the remaining issues.
The dts would need to use the ecoscentric,redboot-fis-partitions
partition parser to get the correct partition offsets and size. It's
expected that the OEM firmware adjusts the on flash partition table with
the values defined in the image header.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use an output image filename based on the compatible string from the dts
files. This way it is way easier to get for which board an image is
intended.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The root filesystem is already part of the factory image and most likely
not required at all.
The same applies to the kernel images.
Signed-off-by: Mathias Kresin <dev@kresin.me>
There is no support for sysupgrade in gemini, hence all images are only
suitable for an installation via bootloader or oem firmware.
Signed-off-by: Mathias Kresin <dev@kresin.me>
For temporary directories <imagename>.tmp is a common pattern in image
build code across the tree. Use it for the nas4220b/sq201 recipe as
well.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Create files in temporary directories within the build directory
instead manipulating files in the (final) output directory.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Due to the missing PROFILES all images are build, regardless of the
selected (or currently processed in case of a multi profile build).
Because of the race condition builds with eight parallel jobs fail,
which can be seen on the build bots as well.
Add the PROFILES variable for now, till the root cause is identified.
Signed-off-by: Mathias Kresin <dev@kresin.me>
When using Image Builder and building image for Cortex A53 or
A72 subtargets, it'll fail with following message:
Collected errors:
* opkg_install_cmd: Cannot install package mwlwifi-firmware-88w8864.
* opkg_install_cmd: Cannot install package mwlwifi-firmware-88w8964.
make[2]: *** [Makefile:153: package_install] Error 255
make[1]: *** [Makefile:114: _call_image] Error 2
This is beacuse both packages are available only for Cortex A9 subtarget
and are included in PACKAGES array in default profile. Instead patching
this, let's remove profiles completely, since all necessary packages are
specified in DEVICE_PACKAGES array for each device.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This removes the misplaced UCI-network configuration for the MR33. The
LAN port is set in 01_leds while it is already correctly defined in
02_network.
This was most likely an oversight as no network configuration belongs
into 01_leds.
Signed-off-by: David Bauer <mail@david-bauer.net>
Enable support for 2nd USB port, which is available on Fritz!Box 7320
and 7330. It was run-tested on 7320 and 7330 as well.
Signed-off-by: Robert Resch <openwrt@webnmail.de>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This commit changes the model string and device title of all AVM boards
to fit the naming of the manufacturer.
Drop all provider-specific titles as they are re-used for every device
generation by 1&1. The original AVM model name is printed on the bottom
of every devices.
Exception applies for boards which are only supported by a specific
sub-revision.
Signed-off-by: David Bauer <mail@david-bauer.net>
Change the "status" LED to proper GPIO 12 and "red" naming.
Remove GPIO 2 from definition as a USB LED.
GPIO 2 is used to control power to the USB socket, not an LED.
As such, PWM on the line or typical LED triggers are inappropriate.
Users who wish to control the USB power for custom applications
can manipulate the GPIO through code, or for example, export it
through /sys/class/gpio/export.
Runtime-tested: GL.iNet AR300M-Lite
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
A missing upstream stable backport leads to the following build error:
CC drivers/mmc/host/sdhci-msm.o
drivers/mmc/host/sdhci-msm.c:1158:3: error: 'const struct sdhci_ops' has no member named 'write_w'
.write_w = sdhci_msm_write_w,
^~~~~~~
drivers/mmc/host/sdhci-msm.c:1158:13: warning: excess elements in struct initializer
.write_w = sdhci_msm_write_w,
^~~~~~~~~~~~~~~~~
drivers/mmc/host/sdhci-msm.c:1158:13: note: (near initialization for 'sdhci_msm_ops')
scripts/Makefile.build:326: recipe for target 'drivers/mmc/host/sdhci-msm.o' failed
Solve the issue by backporting commit
99d570da30 ("mmc: Kconfig: Enable CONFIG_MMC_SDHCI_IO_ACCESSORS")
from linux-stable.
Ref: 528508ae8b (commitcomment-32049231)
Fixes: 528508ae8b ("kernel: bump 4.14 to 4.14.95")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Both Build/sq201-images and Build/nas4220b-images scripts
are very similar. This patch unifies both methods at the
cost of renaming the produced sysupgrade file names, but
with the benifit of creating better reproducible files.
The patch also fixes a race in parallel builds in which case
the ImageInfo of one device could end up in both sysupgrade
files.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Currently, IMAGE_NAME is expanded at declaration time
and this causes strange filename in the builder's logs:
|cp: cannot stat '[...]/openwrt-gemini-dlink-dns-313-.': No such file or directory
|cp: cannot stat '[...]/openwrt-gemini-nas4220b-.': No such file or directory
|[...]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch replaces the current hack with a better
version of the RFC patch has been accepted upstream.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
- remove stray #address-cells / #size-cells
- fix partition unit-addresses in wd-mybooklive.dts
- remove index from MBL's gpio node name
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds the boot-part feature which enables the brcm2708
target move from the custom boot partition size config option to
the generic CONFIG_TARGET_KERNEL_PARTSIZE.
Note:
For people using custom images: Just like with
CONFIG_TARGET_ROOTFS_PARTSIZE changing the value
can cause sysupgrade to repartition the device!
Make sure to have a backup in this case.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Current code directly writes the FOE entry to hash_val+1 position
when hash collision occurs. However, it is found that this behavior
will cause the cache and the hardware FOE table to be inconsistent.
For example, there are three flows, and their hashed values are all
equal to 100. The first flow is written to the position of 100. The
second flow is written to the position of 100+1. Then, the logic of
the current code will also write the third flow to 100+1.
At this time, the cache has flow 1 and 2; and the hardware FOE table
has flow 1 and 3, where these two parts store different contents.
So it is necessary to check whether the hash_val+1 is also occupied
before writing. If hash_val+1 is also occupied, we won’t bind th
third flow to the FOE table.
Addition to that, we also cancel the processing of foe_entry removal
because the hardware has auto age-out ability. The hardware will
periodically iterate through the FOE table to find out the time-out
entry and set it as INVALID.
Signed-off-by: HsiuWen Yen <y.hsiuwen@gmail.com>
LAN ports 1 and 4 and 2 and 3 are interchanged. Fix this in 02_network
so the ports show up in the correct order in luci.
The correct ucidef_add_switch line is already present. This commit moves
the blocks around to keep alphabetical order.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
The swconfig load operation always triggers 'apply' function which in
this driver currently clears port mirroring flags effectively undoing
port mirroring configuration.
This fix preserves port mirroring flags during apply.
Signed-off-by: Milan Krstic <milan.krstic@gmail.com>
The swconfig load operation always triggers 'apply' function which in
this driver currently clears port mirroring flags effectively undoing
port mirroring configuration.
Signed-off-by: Milan Krstic <milan.krstic@gmail.com>
Backport upstream patch:
Commit 65cab850f0ee ("net: Allow class-e address assignment via ifconfig
ioctl") modified the IN_BADCLASS macro a bit, but unfortunatly one too
many '(' characters were added to the line, making any code that used
it, not build properly.
Also, the macro now compares an unsigned with a signed value, which
isn't ok, so fix that up by making both types match properly.
Reported-by: Christopher Ferris <cferris@google.com>
Fixes: 65cab850f0ee ("net: Allow class-e address assignment via ifconfig ioctl")
Cc: Dave Taht <dave.taht@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This patch applies cleanly, so it doesn't cause errors while rebasing
patches. It results in redifinition of inode_still_linked, causing build
to fail when ubifs is enabled. Drop the patch.
Fixes: a37098a2d0 ("kernel: bump 4.19 to 4.19.16")
Reported-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Move the zip compression into a build recipe. Pad the image using the
existing build recipes as well to remove duplicate functionality
Change the code to append header and footer in two steps. Allow to use a
fixed filename as the netgear update image does.
Use a fixed timestamp within the zip archive to make the images
reproducible.
Due to the changes we are now compatible to the gnu89 c standard used by
default on the buildbots and we don't need to force a more recent
standard anymore.
Beside all changes, the footer still looks wrong in compare to the
netgear update image.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This adds supprot for kernel 4.19 to the sunxi target. The patches and
the configuration were copied from the kernel 4.14 patches folder and
adapted for kernel 4.19.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
To make it easier to support multiple kernel versions in parallel also
copy the sub target specific kernel configurations into kernel specific
files.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In the device tree file the higher offsets of the reset controller are
not used, so this patch supporting higher bits is not needed.
The sunxi architecture switched to the simple reset controller with
kernel 4.19 and then this patch does not apply any more.
The sunxi target in OpenWrt is very close to mainline, so if the device
tree files from the mainline Linux kernel need this the mainline kernel
will get support for this.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This configuration option was added in kernel 4.15 and is missing in the
kernel 4.19 configuration.
Fixes: ed2839ac41 ("kernel/modules: add kmod-pmbus-zl6100 module")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds a kernel configuration file for kernel 4.19 on malta.
CONFIG_POWER_RESET_PIIX4_POWEROFF and CONFIG_POWER_RESET_SYSCON were
activated because malta now uses this driver for reboot.
CONFIG_BLK_DEV_SR was also added because it was also added to the kernel
default configuration.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Many MIPS CPUs have optional CPU features which are not activates for
all CPU cores. Print the CPU options which are implemented in the core
in /proc/cpuinfo. This makes it possible to see what features are
supported and which are not supported. This should cover all standard
MIPS extensions, before it only printed information about the main MIPS
ASEs.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This fixes two build problems introduced with the recently added new
kernel module package.
Fixes: ed2839ac41 ("kernel/modules: add kmod-pmbus-zl6100 module")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware
========
CPU: Freescale P1010 PowerPC
RAM: 128M DDR3
NAND: 128MiB
ETH: RTL8211F SGMII PHY
RTL8367B 5-port RGMII switch
(not connected to SoC - unmanaged)
WiFi: SparkLan WPEA-121N
- Atheros AR9382 2T2R abgn
USB: 1x USB 2.0
LED: System, Router, Internet, Tunnel controllable
LAN1-4, WAN, Power non-controllable
BTN: None
Installation
============
1. Power on the device while attached to the Console port.
2. Halt the U-Boot by pressing Enter when prompted.
3. Set the correct bootcmd for booting OpenWRT:
> setenv bootargs_owrt "setenv bootargs console=ttyS0,115200"
> setenv bootcmd "run bootargs_owrt;
nand read 0x1000000 0x300000 0x800000;
bootm 0x1000000;"
> saveenv
5. Rename OpenWRT initramfs image to 'kernel.bin' and place it in a
TFTP server root-directory served on 192.168.1.2/24. Connect your
computer to one of the LAN-ports.
4. Boot OpenWRT initramfs image with
> run bootargs_owrt; tftpboot 0x1000000 192.168.1.2:kernel.bin;
bootm 0x1000000;
6. (Optional)
Make a Backup of 'sophos-os1', 'sophos-os2' and 'sophos-data' in case
you ever want to go back to the vendor firmware.
7. Create Ubi Volume on mtd4 by executing
> ubiformat /dev/mtd4 -y
8. Transfer OpenWRT sysupgrade image to the device via SCP and install it
with
> sysupgrade -n <openwrt-image-file>
Back to Stock
=============
If you want to go back to the stock firmware, here is the bootcmd of the
vendor firmware:
> setenv bootargs console=ttyS0,115200 root=/dev/mtdblock5;
nand read 0xc00000 0x00300000 0x100000;
nand read 0x1000000 0x00400000 0x00800000;
bootm 0x1000000 - 0xc00000
Set it via 'setenv' from the U-Boot shell and don't forget to save it
using 'saveenv'!
After this, boot the OpenWRT initramfs image just like you would for
installation. Write back the three vendor partitions using mtd. Reboot
the device afterwards.
Signed-off-by: David Bauer <mail@david-bauer.net>
[refresh and reorder patches]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Initramfs image isn't required for this device and regular
initramfs generation isn't work properly. It create not working
binaries.
This patch disable initramfs image for TL-WDR4900.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This patch adds the kmod packaging for the Intersil / Zilker Labs
ZL6100 and compatible digital DC-DC controllers as well as the
core kernel module for the Power Management Bus.
Add:
kmod-pmbus-core
kmod-pmbus-zl6100
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
