Use devm_reset_control_array_get_exclusive to register multiple
reset lines in FE driver. This is required to reattach ESW reset to FE
driver again, based on device tree bindings.
While at that, remove unused fe_priv.rst_ppe field, and add error
message if getting the reset fails.
Fixes: 60fadae62b ("ramips: ethernet: ralink: move reset of the esw into the esw instead of fe")
Co-developed-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
[Split out of the bigger commit, provide commit mesage, refactor error
handling]
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit 3f1be8edee)
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
This prevents min_tx_power from functioning properly in some circumstances.
Add the missing newline.
Signed-off-by: Rany Hany <rany_hany@riseup.net>
(cherry picked from commit 6ca8752a9c)
There are broken devices in the wild that handle duplicate IP address
detection by sending out ARP requests for the IP that they received from a
DHCP server and refuse the address if they get a reply.
When proxyarp is enabled, they would go into a loop of requesting an address
and then NAKing it again.
Fixes: https://github.com/openwrt/openwrt/issues/14309
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit c1ad78318c)
Rostelecom RT-FE-1A is a wireless WiFi 5 router manufactured by Sercomm
company.
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB
Flash: 128 MiB
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615E): a/n/ac, 4x4
Ethernet: 5x GbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: No
Button: 2 buttons (Reset & WPS)
LEDs:
- 1x Power (green, unmanaged)
- 1x Status (green, gpio)
- 1x 2.4G (green, hardware, mt76-phy0)
- 1x 2.4G (blue, gpio)
- 1x 5G (green, hardware, mt76-phy1)
- 1x 5G (blue, gpio)
- 5x Ethernet (green, hardware, 4x LAN & WAN)
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot
Installation
-----------------
1. Login to the router web interface (default http://192.168.0.1/)
under "admin" account
2. Navigate to Settings -> Configuration -> Save to Computer
3. Decode the configuration. For example, using cfgtool.py tool (see
related section):
cfgtool.py -u configurationBackup.cfg
4. Open configurationBackup.xml and find the following block:
<OBJECT name="User." type="object" writable="1" encryption="0" >
<OBJECT name="1." type="object" writable="1" encryption="0" >
<PARAMETER name="Password" type="string" value="<some value>" writable="1" encryption="1" password="1" />
</OBJECT>
5. Replace <some value> by a new superadmin password and add a line
which enabling superadmin login after. For example, the block after
the changes:
<OBJECT name="User." type="object" writable="1" encryption="0" >
<OBJECT name="1." type="object" writable="1" encryption="0" >
<PARAMETER name="Password" type="string" value="s0meP@ss" writable="1" encryption="1" password="1" />
<PARAMETER name="Enable" type="boolean" value="1" writable="1" encryption="0"/>
</OBJECT>
6. Encode the configuration. For example, using cfgtool.py tool:
cfgtool.py -p configurationBackup.xml
7. Upload the changed configuration (configurationBackup_changed.cfg) to
the router
8. Login to the router web interface (superadmin:xxxxxxxxxx, where
xxxxxxxxxx is a new password from the p.5)
9. Enable SSH access to the router (Settings -> Access control -> SSH)
10. Connect to the router using SSH shell using superadmin account
11. Run in SSH shell:
sh
12. Make a mtd backup (optional, see related section)
13. Change bootflag to Sercomm1 and reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
reboot
14. Login to the router web interface under admin account
15. Remove dots from the OpenWrt factory image filename
16. Update firmware via web using OpenWrt factory image
Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
cd /tmp
for i in 0 1 2 3 4 5 6 7 8 9; do nanddump -f mtd$i /dev/mtd$i; \
tftp -l mtd$i -p 192.168.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
tftp -l mtd.md5 -p 192.168.0.2
MAC Addresses
-------------
+-----+------------+---------+
| use | address | example |
+-----+------------+---------+
| LAN | label | f4:*:66 |
| WAN | label + 11 | f4:*:71 |
| 2g | label + 2 | f4:*:68 |
| 5g | label + 3 | f4:*:69 |
+-----+------------+---------+
The label MAC address was found in Factory, 0x21000
cfgtool.py
----------
A tool for decoding and encoding Sercomm configs.
Link: https://github.com/r3d5ky/sercomm_cfg_unpacker
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
(cherry picked from commit f3cdc9f988)
This fixes a well known "LZMA ERROR 1" error on Sercomm NA502,
reported on the OpenWrt forum. [1]
[1]: https://forum.openwrt.org/t/176942
Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
(cherry picked from commit d41b8a570f)
Add support for wireless offload package in default configuration for
-Cudy WR3000
-Confiabits MT7981
For some reason those ware missing. I confirm this work for my Cudy WR3000
Signed-off-by: Robert Senderek <robert.senderek@10g.pl>
(cherry picked from commit b42eea0c2f)
fast-xmit must only be enabled after the sta has been uploaded to the driver,
otherwise it could end up passing the not-yet-uploaded sta via drv_tx calls
to the driver, leading to potential crashes because of uninitialized drv_priv
data.
Add a missing sta->uploaded check and re-check fast xmit after inserting a sta.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 438a97fab6)
c739dee0a37b system-linux: refresh MAC address on DSA port conduit change
8587c074f1eb interface-ip: fix IPv4 route target masking
33d6c261aacb system-linux: fix bogus debug error messages on adding bridge members
0832e8f04778 wireless: add bridge_isolate option
5ca7a9058e98 bridge: fix reload on bridge vlan changes
be4ffb3b78bc bridge: rework config change pvid handling
923c4370a1d4 system-linux: set master early on apply settings
b9442415c785 system-linux: skip refreshing MAC on master change if custom MAC
b635a09cdadf system-linux: set pending to 0 on ifindex found or error for if_get_master
2bbe49c36224 device: Log error message if device initialization failed
2703f740a23e Revert "system-linux: set pending to 0 on ifindex found or error for if_get_master"
9cb0cb418303 system-linux: fix race condition in netlink socket error handing
c18cc79d5000 device: restore cleared flags on device down
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Increasing the receive window size improves throughout on higher-latency
links such as WAN connections. The current default of 24KB caps out at
around 500 KB/s.
Increasing the receive buffer to 256KB increases the throughput to at
least 11 MB/s.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit f95eecfb21)
The label-mac of the repeater is the address used on the 2.4 GHz radio,
not the ethernet MAC.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 47818fbc01)
The Puzzle devices come with an I2C-connected Epson RX8130 RTC.
Disable the (dysfunctional) RTC units of the SoC and add driver
kmod-rtc-ds1307 to support the Epson RX8130 instead.
Tested-by: Thomas Huehn <thomas.huehn@hs-nordhausen.de>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 6d546b3b4c)
Confiabits MT7981 is a Wi-Fi 6 router based on MediaTek MT7981.
Specification:
- SoC: MediaTek MT7981B
- CPU: 2x 1.3 GHz Cortex-A53
- Flash: 128 MiB SPI NAND
- RAM: 256 MiB
- WLAN: 2.4 GHz, 5 GHz (MediaTek MT7976CN, 802.11ax)
- Ethernet: 4x 10/100/1000 Mbps MT7531AE (3xLAN, 1xWAN)
- USB 2.0 port
- Buttons: 1 Reset button, 1 Mesh button.
- LEDs: 7x light-blue, 2x warm-white
- Serial console: internal 4-pin header, 115200 8n1
- Power: 12 VDC, 1.5 A
MAC addresses in stock firmware and in this commit:
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| WAN | 00:0c:43:xx:xx:e1 | label+1 |
| LAN | 00:0c:43:xx:xx:e0 | label |
| WLAN 2g | 00:0c:43:xx:xx:e0 | label |
| WLAN 5g | 02:0c:43:xx:xx:e0 | |
+---------+-------------------+-----------+
The label MAC was found in 'Factory', 0x4
Installation:
The stock firmware is OpenWrt-based. If you can reach LuCI or SSH, just use the sysupgrade image
with the 'Keep settings' option turned off.
Signed-off-by: Luis Mita <luis@luismita.com>
(cherry picked from commit 2af07eb853)
Adds the 2 required firmware files for MT7922 chips.
Signed-off-by: Daniel Danzberger <dd@embedd.com>
(cherry picked from commit 9eecf49053)
Signed-off-by: Anya Lin <hukk1996@gmail.com>
In 749237967a downstream dts was replaced with upstream accepted
patch. But in upstream version last partition was called "rootfs"
instead "ubi". OpenWrt require "ubi" label for ubi rootfs.
This patch restore proper label.
Fixes: 749237967a ("kirkwood: Replace dtses with upstream accepted")
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
(cherry picked from commit 9075cfd609)
This service was unfunctional due to not having its executable bit
set.
Fixes#13500.
Signed-off-by: Eric J. Anderson <eric.j.ason256@gmail.com>
(cherry picked from commit 807acbce66)
We have a report in the forum, that lan/wan is non-functional
on the EAP102 (https://forum.openwrt.org/t/edgecore-eap102/178449)
Fixing that by swapping label and phy-handle of the dp-nodes and
updating the lan/wan bmp.
Note: the original commiter of the device support seems absent for a
long time in the forum and on the OpenWrt github group.
Tested-by: Antonio Della Selva <antonio.dellaselva@uniurb.it>
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
Reviewed-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 9b598ec8d5)
[ fix conflicts errors ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Acelink EW-7886CAX is an MT7986A (AKA Filogic 830) based access point.
It has 512 MiB of RAM, one 2.5 Gbps PoE (802.3at) Ethernet port and
on-SoC Wi-Fi. There is no printed MAC label (on my unit).
My unit came with Mediatek's firmware (based on OpenWrt 21.02)
installed. It was possible to simply upgrade using OpenWrt's sysupgrade
tool.
Another verified upgrade method is using U-Boot (requires UART). During
every boot there is "U-Boot Boot Menu". Selecting option "2. Upgrade
firmware" allows using U-Boot's tftp client to load and flash factory
image.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 07765f28b7)
Quite a few `fiilogic` devices use the `mt7531` switch.
Some of them have a DT node that looks like:
```
switch: switch@0 {
compatible = "mediatek,mt7531";
reg = <31>;
...
};
```
This commit changes the DT node name to `switch@1f`.
Signed-off-by: Rani Hod <rani.hod@gmail.com>
(cherry picked from commit aaeb379023)
Fix the issue of dts buswidth cannot be applied properly with spi driver.
Fix the name of buswidth to bus-width in dts in order to fit the format
in linux spi kernel[1] so that spi-tx-bus-width & spi-rx-bus-width can be
parsed properly.
[1] Documentation/devicetree/bindings/spi/spi-controller.yaml
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
(cherry picked from commit 36746893ac)
The PGIO configuration should be added for the ZBT-Z8102AX and not the ZBT-Z8103AX
Fixes: c8c2f52262 ("mediatek: add support for Zbtlink ZBT-Z8102AX")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit d99aed31a0)
Fix typo calling lua53 instead of lua5.3 for Package Default definition.
This cause only missing description of the package and doesn't cause
any build regression.
Fixes: c52ca08d40 ("lua5.3: build shared library")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 25e215c14e)
Specifications:
SoC: MediaTek MT7981B
RAM: 1024MiB
Flash: SPI-NAND 128 MiB
Switch: 1 WAN, 4 LAN (Gigabit)
USB: two M.2 slots for 5G modems via USB 3.0 hub, external USB 3.0 port
Buttons: Reset, Mesh
Power: DC 12V 1A
WiFi: MT7976CN
UART: 115200n8
UART Layout:
VCC-RX-TX-GND
Installation:
A. Through OpenWrt Dashboard:
If your router comes with OpenWrt preinstalled (modified by the seller),
you can easily upgrade by going to the dashboard (192.168.1.1) and then
navigate to System -> Backup/Flash firmware, then flash the firmware
B. Through TFTP
Standard installation via UART:
1. Connect USB Serial Adapter to the UART, (NOTE: Don't connect the VCC pin).
2. Power on the router. Make sure that you can access your router via UART.
3. Restart the router then repeatedly press ctrl + c to skip default boot.
4. Type > bootmenu
5. Press '2' to select upgrade firmware
6. Press 'Y' on 'Run image after upgrading?'
7. Press '0' and hit 'enter' to select TFTP client (default)
8. Fill the U-Boot's IP address and TFTP server's IP address.
9. Finally, enter the 'firmware' filename.
Based on patch adding support for similar Zbtlink ZBT-Z8103AX device by
Ian Ishmael C. Oderon.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit c8c2f52262)
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: Winbond 128MB
RAM: DDR3 256MB
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset
Power: DC 12V 1A
Flash instructions:
1. Connect to your PC via the Gigabit port of the router,
set a static ip on the ethernet interface of your PC.
(ip 192.168.1.254, gateway 192.168.1.1)
2. Attach UART, pause at u-boot menu.
3. Select "Upgrade ATF BL2", then use preloader.bin
4. Select "Upgrade ATF FIP", then use bl31-uboot.fip
5. Download the initramfs image, and type "reset",
waiting for tftp recovery to complete.
6. After openwrt boots up, perform sysupgrade.
Note:
1. Since NMBM is disabled, we must back up all partitions.
2. Although we can upgrade new firmware in the stock firmware,
we need the special fit image signature of MediaTek and
dual boot (hack kernel) to make u-boot boot it. So just
abandon these hacks and flash it via the serial port.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit 626344c992)
The vendor uboot will verify firmware at boot.
So add a custom uboot build for this device.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit b42c527228)
Hardware
========
SOC: MediaTek MT7986
RAM: 512MB DDR3
FLASH: 256MB SPI-NAND
WIFI: Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz 4T4R
ETH: MediaTek MT7530 Switch (LAN)
MaxLinear GPY211C 2.5 N-Base-T PHY (WAN)
MaxLinear GPY211C 2.5 N-Base-T PHY (LAN)
UART: 3V3 115200 8N1 (Do not connect VCC)
USB 3.1
Installation
============
Download the OpenWrt initramfs image. Copy the image to a TFTP server
reachable at 192.168.1.70/24. Rename the image to TUF-AX6000.bin.
Connect to the serial console, interrupt the auto boot process by
pressing '4' when prompted or press '1' and set client IP, server
IP and name of the image.
yOU don't need to open the case or even soldering anything.
use three goldpin wires, remove their plastic cover and connect
them to the console pinout via the case holes.
You can see three holes
From Bottom: RX, TX, Ground - partially covered
Download & Boot the OpenWrt initramfs image.
In case of option '4'
$ setenv ipaddr 192.168.1.1
$ setenv serverip 192.168.1.70
$ tftpboot 0x46000000 TUF-AX6000.bin
$ bootm 0x46000000
In case of option '1'
1: Load System code to SDRAM via TFTP.
Please Input new ones /or Ctrl-C to discard
Input device IP (192.168.1.1) ==:
Input server IP (192.168.1.70) ==:
Input Linux Kernel filename (TUF-AX6000.trx) ==:
Wait for OpenWrt to boot. Transfer the sysupgrade
image to the device using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
Missing features
================
2.5Gb LAN port LED is ON during boot or when the LAN cable is disconnected
The cover yellow light is not supported. (only blue one)
Signed-off-by: Patryk Kowalczyk <patryk@kowalczyk.ws>
(cherry picked from commit d522ccecb2)
Let ucode-mod-* packages select the ucode interpreter instead of depending
on it to avoid recursive dependency chains in unrelated packages.
Fixes: https://github.com/openwrt/packages/issues/22837
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(cherry picked from commit 01d1c1ad29)
Commit mt76: drop default eeprom file for mt7986-firmware
(e3aa645b26) breaks eeprom loading for
Mercusys MR90X v1. As a result WiFi is not working at all.
This commit adds Mercusus MR90x to the caldata script (it works after the
commit mentioned above). And we can safely drop "81_fix_eeprom" script
as it's no longer required.
Fixes: 5a0bdab24c ("mt76: drop default eeprom file for mt7986-firmware")
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
(cherry picked from commit 85b0d7592c)
[rmilecki: fix commit hash in Fixes]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The mt76 driver usually reads the eeprom on the mtd partition at dts.
For emmc device we need to use caldata_extract script to read the
eeprom. However, the default eeprom file breaks the caldata script
execution, so remove it.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit e3aa645b26)
The usb driver requires kmod-usb3, not kmod-usb2.
Remove the useless kmod-usb2 from default package.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit b74ae69596)
**Hardware specification:**
- SoC: MediaTek MT7981B 2x A53
- Flash: ESMT F50L1G41LB 128MB
- RAM: Nanya NT5CC128M16JR-EK 256MB
- Ethernet: 4 x 10/100/1000 Mbps
- Switch: MediaTek MT7531AE
- WiFi: MediaTek MT7976C
- Button: Reset, Mesh
- Power: DC 12V 1A
- UART: 3.3v, 115200n8
| Layout: |
| :-------- |
| <Antenna> |
| VCC |
| GND |
| Tx |
| Rx |
**Flash instructions:**
1. Rename `openwrt-mediatek-filogic-cetron_ct3003-squashfs-factory.bin` to `factory.bin`.
2. Upload the `factory.bin` using the device's Web interface.
3. Click the upgrade button and wait for the process to finish.
4. Access the OpenWrt interface using the same password.
5. Use the 'Restore' function to reset the firmware to its initial state.
**Notes:**
If you plan to recovery the stock firmware in the future, it's advisable
to connect the device via the serial port and enter failsafe mode to
back up all the MTD partitions before proceeding the steps above.
Signed-off-by: Patricia Lee <patricialee320@gmail.com>
(cherry picked from commit 907e9e0bd3)
Telenor quirks
--------------
The operator specific firmware running on the Telenor branded
ZyXEL EX5700 includes U-Boot modifications affecting the OpenWrt
installation.
Notable changes to U-Boot include
- environment is stored in RAM and reset to defaults when power
cycled
- dual partition scheme with "nomimal" or "rescue" systems, falling
back to "rescue" unless the OS signals success in 3 attempts
- several runtime additions to the device-tree
Some of these modifications have side effects requiring workarounds
- U-Boot modifies /chosen/bootargs in an unsafe manner, and will crash
unless this node exists
- U-Boot verifies that the selected rootfs UBI volume exists, and
refuses to boot if it doesn't. The chosen "rootfs" volume must contain
a squashfs signature even for tftp or initramfs booting.
- U-Boot parses the "factoryparams" UBI volume, setting the "ethaddr"
variable to the label mac. But "factoryparams" does not always
exist. Instead there is a "RIP" volume containing all the factory
data. Copying the "RIP" volume to "factoryparams" will fix this
Hardware
--------
SOC: MediaTek MT7986
RAM: 1GB DDR4
FLASH: 512MB SPI-NAND (Mikron xxx)
WIFI: Mediatek MT7986 802.11ax 5 GHz
Mediatek MT7916 DBDC 802.11ax 2.4 + 6 GHz
ETH: MediaTek MT7531 Switch + SoC
3 x builtin 1G phy (lan1, lan2, lan3)
2 x MaxLinear GPY211C 2.5 N-Base-T phy (lan4, wan)
USB: 1 x USB 3.2 Enhanced SuperSpeed port
UART: 3V3 115200 8N1 (Pinout: GND KEY RX TX VCC)
Installation
------------
1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
reachable at 192.168.1.2/24. Rename the image to C0A80101.img.
2. Connect the TFTP server to lan1, lan2 or lan3. Connect to the serial
console, Interrupt the autoboot process by pressing ESC when prompted.
3. Download and boot the OpenWrt initramfs image.
$ env set uboot_bootcount 0
$ env set firmware nominal
$ tftpboot
$ bootm
4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
Missing features
----------------
- The "lan1", "lan2" and "lan3" port LEDs are driven by the switch but
OpenWrt does not correctly configure the output.
- The "lan4" and "wan" port LEDs are driven by the GPH211C phys and
not configured by OpenWrt.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
(cherry picked from commit 6cc14bf66a)
The 'label' property in led node has been deprecated and we'd better
to avoid using it. This patch allows us to extract DT OF LED name
from the newly introduced LED properties "color", "function" and
"function-enumerator".
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit e814acc599)
The no-map property was incorrectly added, which kept the system-memory
available on the WS-AP3825 limited to 190MB. We are allowed to map the
page containing the CPU1 spin-table, we are just not allowed to write to
it.
Fixes: 57d7382cb1 ("mpc85xx: increase available RAM on Extreme Networks WS-AP3825i")
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit d9271aa5b7)
The system-mamory size was page-aligned prior to this commit, only
enabling to use 192MB of system memory of the 256 available.
This was due to the system-memory being manually shrinked to reserve the
upper 1MB for the second-core bootpage in the loader as well as the OS.
Fix this properly in the loader and in Linux using reserved-memory
definitions. This enables the device to use 250MB of system memory.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 57d7382cb1)
1d42292d8063 tplink-safeloader: Add TP-Link Archer A6 V3.20
3338f5389d72 tplink-safeloader: add TL-WPA8635P v3
17ca5eeb1c10 tplink-safeloader: add TL-WPA8631P v4
f730ad2fa0b4 bcmblob: new tool for reading Broadcom's BLOBs
cb1ddac98124 firmware-utils: fix typo in error message when no OpenSSL library found
916633160dc9 bcmclm: new tool for reading Broadcom's CLM data
a2d49fb1e188 tplink-safeloader: add RU support-list entry for Archer C6U v1
bb12cf5c3fa9 tplink-safeloader: Add support for TP-Link Deco M5 The special_id values are the same for EU and Asian models, and they apply to all models: v1, v2, and v3. They are not sorted as they are currently in the same order as extracted from the official firmware image.
9e2de8515be1 tplink-safeloader: add EAP610 v3 and EAP613 v1
a170683c0e11 firmware-utils: fix use of NULL string progname
89875fc18b57 tplink-safeloader: CPE510: add Canadian support
9e211d2980fe mktplinkfw2: add support to extract bootloader images
c18f662f3c74 mktplinkfw2: add support to pack bootloader
3dc133915f87 mktplinkfw2: show exact exceed bytes when the image is to big
d16ff798d58a tplink-safeloader: WPA8631: add v4 AU, US
0fa1cc51013f zytrx: add LTE5398-M904
635466123429 firmware-utils: ptgen: add SiFive GPT partition support
ba5bc4e1ae9d add dlink-sge-image for D-Link devices by SGE
3b114de29cf7 lxlfw: move code opening LXL to helper function
8e149e480391 lxlfw: move code copying data to helper function
16fa89076122 lxlfw: fix struct lxl_hdr attribute
d770cab82e58 lxlfw: support embedding blobs
eaf2ea28dbe6 lxlfw: support extracting image
12bf1a99bd6e lxlfw: support certificate & signature blobs
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit b117e7244f)
This commit adds support for following wireless routers:
- Rostelecom RT-FL-1 (Serсomm RT-FL-1)
- Rostelecom S1010 (Serсomm S1010.RT)
The devices are almost identical and the only difference is one bit in the
factory image PID (thanks to Maximilian Weinmann <x1@disroot.org>
(@MaxS0niX) for the info and idea to make one PR for two devices at once).
Devices specification
---------------------
SoC: MediaTek MT7620A, MIPS
RAM: 64 MB
Flash: 16 MB SPI NOR
Wireless 2.4: MT7620 (b/g/n, 2x2)
Wireless 5: MT7612EN (a/n/ac, 2x2)
Ethernet: 5xFE (WAN, LAN1-4)
BootLoader: U-Boot
Buttons: 2 (wps, reset)
LEDs: 1 amber and 1 green status GPIO leds
5 green ethernet GPIO leds
1 green GPIO 2.4 GHz WLAN led
1 green PHY 5 GHz WLAN led
1 green unmanaged power led
USB ports: No
Power: 12 VDC, 1 A
Connector: Barrel
OEM easy installation
---------------------
1. Remove all dots from the factory image filename (except the dot
before file extension)
2. Upload and update the firmware via the original web interface
3. Wait until green status led stops blinking (can take several minutes)
4. Login to OpenWrt initramsfs. It's recommended to make a backup of the
mtd partitions at this point.
4. Perform sysupgrade using the following command (or use Luci):
sysupgrade -n sysupgrade.bin
5. Wait until green status les stops blinking (can take several minutes)
6. Mission acomplished
Return to Stock
---------------
Option 1. Restore firmware Slot1 from a backup (firmware2.bin):
cd /tmp
mtd -e Firmware2 write firmware2.bin Firmware2
printf 1 | dd bs=1 seek=$((0x18007)) count=1 of=/dev/mtdblock2
reboot
Option 2. Decrypt, ungzip and split stock firmware image into the parts,
take Slot1 parts (kernel2.bin, rootfs2.bin) and write them:
cd /tmp
mtd -e Kernel2 write kernel2.bin Kernel2
mtd -e RootFS2 write rootfs2.bin RootFS2
printf 1 | dd bs=1 seek=$((0x18007)) count=1 of=/dev/mtdblock2
reboot
More about stock firmware decryption:
Link: https://github.com/Psychotropos/sercomm_fwutils/
Debricking
----------
Use sercomm-recovery tool. You can use "ALL" mtd partition backup as a
recovery image.
Link: https://github.com/danitool/sercomm-recovery
MAC addresses
-------------
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| label | 48:3e:xx:xx:xx:1e | label |
| LAN | 48:3e:xx:xx:xx:1e | label |
| WAN | 48:3e:xx:xx:xx:28 | label+10 |
| WLAN 2g | 48:3e:xx:xx:xx:20 | label+2 |
| WLAN 5g | 48:3e:xx:xx:xx:24 | label+6 |
+---------+-------------------+-----------+
Co-authored-by: Vadzim Vabishchevich <bestmc2009@gmail.com>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
(cherry picked from commit 1b091311aa)
[fix rt2800_wmac eeprom load]
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
This commit makes a common recipe to set bit in Sercomm factory pid since
this is necessary for several devices (WiFire S1500.nbn, Rostelecom
RT-FL-1) at different offsets.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
(cherry picked from commit e900c45211)
It's required by bcm53xx. This allows dropping separated oseama package
and avoids some code duplication.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 1d9d0ca376)
