Commit Graph

26219 Commits

Author SHA1 Message Date
Sven Eckelmann
97f5617259 ath79: Add support for OpenMesh OM5P-AC v1
Device specifications:
======================

* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi (11n)
* 2T2R 5 GHz Wi-Fi (11ac)
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring
* 2x ethernet
  - eth0
    + AR8035 ethernet PHY (RGMII)
    + 10/100/1000 Mbps Ethernet
    + 802.3af POE
    + used as LAN interface
  - eth1
    + AR8035 ethernet PHY (SGMII)
    + 10/100/1000 Mbps Ethernet
    + 18-24V passive POE (mode B)
    + used as WAN interface
* 12-24V 1A DC
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

   setenv serverip 192.168.1.21
   setenv ipaddr 192.168.1.1
   tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to the
device via

  scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

  sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2022-01-09 21:12:28 +01:00
Sven Eckelmann
72ef594550 ath79: Add support for OpenMesh OM5P-AN
Device specifications:
======================

* Qualcomm/Atheros AR9344 rev 2
* 560/450/225 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 1T1R 2.4 GHz Wi-Fi
* 2T2R 5 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring
* 2x ethernet
  - eth0
    + AR8035 ethernet PHY
    + 10/100/1000 Mbps Ethernet
    + 802.3af POE
    + used as LAN interface
  - eth1
    + 10/100 Mbps Ethernet
    + builtin switch port 1
    + 18-24V passive POE (mode B)
    + used as WAN interface
* 12-24V 1A DC
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

   setenv serverip 192.168.1.21
   setenv ipaddr 192.168.1.1
   tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to the
device via

  scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

  sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2022-01-09 21:12:28 +01:00
Tamas Balogh
b29f4cf34c ath79: add support for ASUS RP-AC66
Asus RP-AC66 Repeater

Hardware specifications:
Board: AP152
SoC: QCA9563
DRAM: 64MB DDR2
Flash: 25l128 16MB SPI-NOR
LAN/WAN: 1x1000M QCA8033
WiFi 5GHz: QCA9880
Clocks: CPU:775.000MHz, DDR:650.000MHz, AHB:258.333MHz, Ref:25.000MHz

MAC addresses as verified by OEM firmware:
use            address   source
Lan/Wan   *:24         art 0x1002 (label)
2G             *:24         art 0x1002
5G             *:26         art 0x5006

Installation:

Asus windows recovery tool:
 - install the Asus firmware restoration utility
 - unplug the router, hold the reset button while powering it on
 - release when the power LED flashes slowly
 - specify a static IP on your computer:
     IP address: 192.168.1.75
     Subnet mask 255.255.255.0
 - Start the Asus firmware restoration utility, specify the factory image
    and press upload
 - Do not power off the device after OpenWrt has booted until the LED flashing.

TFTP Recovery method:
 - set computer to a static ip, 192.168.1.75
 - connect computer to the LAN 1 port of the router
 - hold the reset button while powering on the router for a few seconds
 - send firmware image using a tftp client; i.e from linux:
 $ tftp
 tftp> binary
 tftp> connect 192.168.1.1
 tftp> put factory.bin
 tftp> quit

Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
2022-01-09 20:32:41 +01:00
Fritz D. Ansel
693958497a mediatek mt7622: fix 300mhz typo in dts
The lowest frequency should be 300MHz, since that is the label
assigned to the OPP in the mt7622.dtsi device tree, while there is one
missing zero in the actual value.

To be clear, the lowest frequency should be 300MHz instead of 30MHz.

As mentioned @dangowrt on the OpenWrt forum there is no benefit in
leaving 30MHz as the lowest frequency.

Signed-off-by: Jip de Beer <gpk6x3591g0l@opayq.com>
Signed-off-by: Fritz D. Ansel <fdansel@yandex.ru>
2022-01-09 14:48:16 +00:00
Stefan Lippers-Hollmann
abc2821286 x86: improve sysinfo handling of dummy values
Fall back to using board_vendor and board_name, if known dummy values
are used for sys_vendor and product_name.

Examples:
	To be filled by O.E.M.:To be filled by O.E.M.
-->	INTEL Corporation:ChiefRiver

	System manufacturer:System Product Name
-->	ASUSTeK COMPUTER INC.:P8H77-M PRO

	To Be Filled By O.E.M.:To Be Filled By O.E.M.
-->	ASRock:Q1900DC-ITX

	Gigabyte Technology Co., Ltd.:To be filled by O.E.M.
-->	Gigabyte Technology Co., Ltd.:H77M-D3H

	empty:empty
-->	TYAN Computer Corporation:TYAN Toledo i3210W/i3200R S5211

	To Be Filled By O.E.M.:To Be Filled By O.E.M.
-->	ASRock:H77 Pro4-M

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2022-01-08 23:25:05 +01:00
Alex Lewontin
62a2bfaff8 ipq806x: janitorial work, respect line lengths
This commit breaks up some lines so that they are shorter than
74 charcters.

Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
2022-01-08 23:25:05 +01:00
Alex Lewontin
479acf03cc ipq806x: modularize generic subtarget
This commit moves the device profiles within the ipq806x/generic
subtarget into their own includable .mk file, to support eventually
having subtargets other than generic.

Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
2022-01-08 23:25:05 +01:00
Aleksander Jan Bajkowski
46468fc9d5 lantiq: replace patches with version accepted upstream
Replace recently added patches with version accepted upstream.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-01-08 19:32:45 +01:00
Nick McKinney
e0a574d4b7 ramips: add support for Linksys EA6350 v4
Specifications:
- SoC: MT7621DAT (880MHz, 2 Cores)
- RAM: 128 MB
- Flash: 128 MB NAND
- Ethernet: 5x 1GiE MT7530
- WiFi: MT7603/MT7613
- USB: 1x USB 3.0

This is another MT7621 device, very similar to other Linksys EA7300
series devices.

Installation:

Upload the generated factory.bin image via the stock web firmware
updater.

Reverting to factory firmware:

Like other EA7300 devices, this device has an A/B router configuration
to prevent bricking.  Hard-resetting this device three (3) times will
put the device in failsafe (default) mode.  At this point, flash the
OEM image to itself and reboot.  This puts the router back into the 'B'
image and allows for a firmware upgrade.

Troubleshooting:

If the firmware will not boot, first restore the factory as described
above.  This will then allow the factory.bin update to be applied
properly.

Signed-off-by: Nick McKinney <nick@ndmckinney.net>
2022-01-08 00:49:59 +01:00
Liangkuan Yang
bc7d36ba3a ramips: add support for RAISECOM MSG1500 X.00
RAISECOM MSG1500 X.00 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router.
Apart from the general model, there are two ISP customized models:
China Mobile and China Telecom.

Specifications:

- SoC: Mediatek MT7621AT
- RAM: 256MiB DDR3
- Flash: 128MiB NAND
- Ethernet: 5 * 10/100/1000Mbps: 4 * LAN + 1 * WAN
  - Switch: MediaTek MT7530 (SoC)
- WLAN: 1 * MT7615DN Dual-Band 2.4GHz 2T2R (400Mbps) 5GHz 2T2R (867Mbps)
- USB: 1 * USB 2.0 port
- Button: 1 * RESET button, 1 * WPS button, 1 * WIFI button
- LED: blue color: POWER, WAN, WPS, 2.4G, 5G, LAN1, LAN2, LAN3, LAN4, USB
- UART: 1 * serial port header (4-pin)
- Power: DC 12V, 1A
  - Switch: 1 * POWER switch

MAC addresses as verified by vendor firmware:

use   address             source
LAN   C8:XX:XX:3A:XX:E7   Config   "protest_lan_mac"  ascii  (label)
WAN   C8:XX:XX:3A:XX:EA   Config   "protest_wan_mac"  ascii
5G    C8:XX:XX:3A:XX:E8   Factory  "0x4"              hex
2.4G  CA:XX:XX:4A:XX:E8   [not on flash]

The increment of the 4th byte for the 2.4g address appears to vary.
Reported cases:

       5g                 2.4g         increment
 C8:XX:XX:90:XX:C3  CA:XX:XX:C0:XX:C3  0x30
 C8:XX:XX:3A:XX:08  CA:XX:XX:4A:XX:08  0x10
 C8:XX:XX:3A:XX:E8  CA:XX:XX:4A:XX:E8  0x10

Since increment is inconsistent and there is no obvious pattern
in swapping bytes, and the 2.4g address has local bit set anyway,
it seems safer to use the LAN address with flipped byte here in
order to prevent collisions between OpenWrt devices and OEM devices
for this interface. This way we at least use an address as base
that is definitely owned by the device at hand.

Notes:

1. The vendor firmware allows you to connect to the router by telnet.
   (known version 1.0.0 can open telnet.)
   There is no official binary firmware available.
   Backup the important partitions data:
   "Bootloader", "Config", "Factory", and "firmware".
   Note that with the vendor firmware the memory is detected only 128MiB
   and the last 512KiB in NAND flash is not used.

2. The POWER LED is default on after press POWER switch.
   The WAN and LAN1 - 4 LEDs are wired to ethernet switch.
   The WPS LED is controlled by MT7615DN's GPIO.
   Currently there is no proper way to configure it.

3. At the time of adding support the wireless config needs to be set up
   by editing the wireless config file:

 * Setting the country code is mandatory, otherwise the router loses
   connectivity at the next reboot. This is mandatory and can be done
   from luci. After setting the country code the router boots correctly.
   A reset with the reset button will fix the issue and the user has to
   reconfigure.

 * This is minor since the 5g interface does not come up online although
   it is not set as disabled. 2 options here:

   1- Either run the "wifi" command. Can be added from LuCI in system -
      startup - local startup and just add wifi above "exit 0".

   2- Or add the serialize option in the wireless config file as shown
      below. This one would work and bring both interfaces automatically
      at every boot:

      config wifi-device 'radio0'
          option serialize '1'

      config wifi-device 'radio1'
          option serialize '1'

Flash instructions using initramfs image:

1. Press POWER switch to power down if the router is running.

2. Connect PC to one of LAN ports, and set
   static IP address to "10.10.10.2", netmask to "255.255.255.0",
   and gateway to "10.10.10.1" manually on the PC.

3. Push and hold the WIFI button, and then power up the router.
   After about 10s (or you can call the recovery page, see "4" below)
   you can release the WIFI button.
   There is no clear indication when the router
   is entering or has entered into "RAISECOM Router Recovery Mode".

4. Call the recovery page for the router at "http://10.10.10.1".
   Keep an eye on the "WARNING!! tip" of the recovery page.
   Click "Choose File" to select initramfs image, then click "Upload".

5. If image is uploaded successfully, you will see the page display
   "Device is upgrading the firmware... %".
   Keep an eye on the "WARNING!! tip" of the recovery page.
   When the page display "Upgrade Successfully",
   you can set IP address as "automatically obtain".

6. After the rebooting (PC should automatically obtain an IP address),
   open the SSH connection, then download the sysupgrade image
   to the router and perform sysupgrade with it.

Flash back to vendor firmware:

 See "Flash instructions 1 - 5" above.
 The only difference is that in step 4
 you should select the vendor firmware which you backup.

Signed-off-by: Liangkuan Yang <ylk951207@gmail.com>
2022-01-08 00:49:59 +01:00
Rodrigo Araujo
766733e172 ramips: add support for Joowin WR758AC V1 and V2
This commit adds support for Joowin (aka Comfast) WR758AC V1 and V2
devices.

Both have the same wall AP/repeater form factor and differ only
in the 5Ghz chipset (V1 has MT7662, V2 has MT7663).

OpenWrt developers forum page:
https://forum.openwrt.org/t/87355

Specifications:

 - CPU: MediaTek MT7628AN (580MHz)
 - Flash: 8MB
 - RAM: 64MB DDR2
 - 2.4 GHz: 802.11b/g/n (MT7603)
 - 5 GHz: 802.11ac (V1 has MT7662, V2 has MT7663)
 - Antennas: 4x external single band antennas
 - LAN: 1x 10/100M
 - LED: Wifi 3x blue. Programmable
 - Button: WPS

MAC addresses as verified by OEM firmware:

use address source
LAN *:83 factory 0xe000
2g *:85 factory 0x4
5g *:86 factory 0x8004

How to install:
1- Setup a TFTP server on a machine with IP address 192.168.1.10/24
2- Name the image as `firmware_auto.bin` and place it on the root of the
TFTP server
3- Connect the device via Ethernet, it should pick and flash the image

Signed-off-by: Rodrigo Araujo <araujo.rm@gmail.com>
2022-01-08 00:49:59 +01:00
Rui Salvaterra
536f051b97 kernel: bump 5.10 to 5.10.90
Add and enable a new kconfig knob to disable unprivileged eBPF by default.

Patches automatically rebased.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2022-01-07 22:30:40 +01:00
John Audia
9f08557649 kernel: bump 5.4 to 5.4.170
All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/mt7621

Signed-off-by: John Audia <graysky@archlinux.us>
2022-01-07 22:30:40 +01:00
Daniel Golle
87b6e10c71
mediatek: Clause-45 MDIO patch accepted upstream
To easy future maintainance, replace the local patch with what has been
accepted into net-next and is likely to end up in Linux 5.17.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-01-05 14:33:56 +00:00
Matt Fawcett
b2d769673a qoriq: Expand generic subtarget description
Signed-off-by: Matt Fawcett <mattytap@icloud.com>
[remove trailing whitespace]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-01-05 10:54:59 +02:00
Daniel Golle
ef1a64caf4
mediatek: let mtk_eth_soc MAC announce 2500Base-T mode
To allows Ethernet phys supporting 2500Base-T mode to announce that
speed, enable the corresponding bit in mtk_eth_soc driver.
This should hopefully unlock 2500Base-T speed on the UniFi 6 LR.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-01-05 00:57:43 +00:00
Daniel Golle
6c312d9717
kernel: improve driver support for gen-3 Aquantia Ethernet PHYs
* correctly set system side interface, the original patch was
   errornous and there is a follow-up fix for it
 * enable phy statistics for AQR112(+R/C) and ARQ412
   (ethtool --phy-statistics ethX)

Tested, including phy-statistics, on
 - IEI Puzzle M901 (AQR112, AQR112C, AQR112R)
 - IEI Puzzle M902 (AQR113, AQR112R)
 - Ubiquiti UniFi 6 LR (AQR112C)

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-01-05 00:57:25 +00:00
Paul Spooren
cb85aea869 uml: drop Kernel 5.4
After the switch to Kernel 5.10 the old files are no longer required.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2022-01-04 13:06:03 +01:00
Paul Spooren
02852d5538 uml: switch to Kernel 5.10
Switch over from testing version.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2022-01-04 13:05:13 +01:00
Paul Spooren
4a2cca7824 ipq807x: drop target
The target is in an incomplete state and will not receive Kernel 5.10
support, ego it should be dropped before the next release.

People are working on ipq807x with Kernel 5.15 which is only relevant
for the second next release. Once a working patchset exists the target
can be added again.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2022-01-03 10:36:09 +01:00
Ansuel Smith
1e4469b090 kernel: 5.10: backport qca8k new feature
Backport qca8k new feature:
- Ageing configuration support
- Add 2 missing counter on qca8337
- Convert to regmap
- Standardize define and code with GENMASK AND BITFILED macro
- Add mdb add/del support

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2022-01-03 01:00:04 +01:00
Ansuel Smith
5cf198f764 kernel: 5.10: backport additional qca8k fixes
Backport 3 additional fixes for qca8k.
- Fix MTU calculation
- Fix a bug with config set to the wrong PAD when secondary cpu port is defined.
- Fix redundant check in parse_port_config

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2022-01-03 01:00:04 +01:00
Rui Salvaterra
2bb02ccae3 kernel: bump 5.10 to 5.10.89
Deleted (upstreamed):
bcm27xx/patches-5.10/950-0186-pinctrl-bcm2835-Change-init-order-for-gpio-hogs.patch [1]
sunxi/patches-5.10/103-arm64-dts-allwinner-orangepi-zero-plus-fix-PHY-mo.patch [2]

[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.89&id=ba696b470839d70c6b8290c1f798bac7fb2a584c
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.89&id=93a957bbf46ceb224b959de61fe85cfc6f71b6c7

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2022-01-03 01:00:03 +01:00
John Audia
7bf62e2451 kernel: bump 5.4 to 5.4.169
All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/mt7621*

*Had to revert 7f1edbd in order to build due to FS#4149

Signed-off-by: John Audia <graysky@archlinux.us>
2022-01-03 01:00:03 +01:00
Stefan Lippers-Hollmann
d9c2b0cfdd ipq806x: ASRock g10: fix bogus read errors
Properly declare that the g10 is booting from NAND and define its
correct (larger than on other devices-) boot_pages_size, to prevent
the kernel from constantly falling over missing OOB error correction
for the bootloader.

This patch prevents a constant slew of (bogus) read errors reported
by the kernel and keeping the CPU busy and fixes:

blk_update_request: I/O error, dev mtdblock0, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 0
blk_update_request: I/O error, dev mtdblock0, sector 8 op 0x0:(READ) flags 0x80700 phys_seg 3 prio class 0
blk_update_request: I/O error, dev mtdblock0, sector 16 op 0x0:(READ) flags 0x80700 phys_seg 2 prio class 0
blk_update_request: I/O error, dev mtdblock0, sector 24 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0
blk_update_request: I/O error, dev mtdblock0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
Buffer I/O error on dev mtdblock0, logical block 0, async page read
blk_update_request: I/O error, dev mtdblock0, sector 32 op 0x0:(READ) flags 0x80700 phys_seg 8 prio class 0
blk_update_request: I/O error, dev mtdblock0, sector 40 op 0x0:(READ) flags 0x80700 phys_seg 7 prio class 0
blk_update_request: I/O error, dev mtdblock0, sector 48 op 0x0:(READ) flags 0x80700 phys_seg 6 prio class 0
blk_update_request: I/O error, dev mtdblock0, sector 56 op 0x0:(READ) flags 0x80700 phys_seg 5 prio class 0
blk_update_request: I/O error, dev mtdblock0, sector 64 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 0
Buffer I/O error on dev mtdblock0, logical block 1, async page read
Buffer I/O error on dev mtdblock1, logical block 0, async page read
Buffer I/O error on dev mtdblock1, logical block 1, async page read
Buffer I/O error on dev mtdblock2, logical block 0, async page read
Buffer I/O error on dev mtdblock2, logical block 1, async page read
Buffer I/O error on dev mtdblock3, logical block 0, async page read
Buffer I/O error on dev mtdblock3, logical block 0, async page read
Buffer I/O error on dev mtdblock4, logical block 0, async page read
Buffer I/O error on dev mtdblock4, logical block 1, async page read

Suggested-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2022-01-02 20:41:50 +01:00
Shiji Yang
86d019d116 ramips: add ASUS RT-AC1200GU as alt name
RT-AC57U and RT-AC1200GU are the same models sold in different countries.
The purpose of this commit is to allow users to easily find the
corresponding firmware through the model number on the device label.

More specifications: 14e0e4f138 ("ramips: add support for ASUS RT-AC57U")

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[reword commit title/message]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-02 01:31:02 +09:00
Sungbo Eo
a1deab0ec9 ramips: add support for ipTIME T5004
ipTIME T5004 is a 5-port Gigabit Ethernet router, based on MediaTek MT7621A.

Specifications:
* SoC: MT7621AT
* RAM: 128 MiB
* Flash: NAND 128 MiB
* Ethernet: 5x 1GbE
  * Switch: SoC built-in
* UART: J4 (57600 baud)
  * Pinout: [3V3] (TXD) (RXD) (GND)

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware via recovery mode:
1.  Press reset button, power up the device, wait >15s for CPU LED
    to stop blinking.
2.  Upload stock image to TFTP server at 192.168.0.1.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-02 00:50:43 +09:00
Raylynn Knight
2e1206ad23 x86: add/improve support for Sophos SG/XG products
* Add support for Sophos SG/XG-115 r1, r2 with/without wireless
* Add support for Sophos SG/XG-125 r1, r2 with/without wireless
* Add wireless support for SG/XG-105

Signed-off-by: Raylynn Knight <rayknight@me.com>
2021-12-29 22:55:16 +01:00
Jinfan Lei
3928f6ae5c ath79: add usb-phy-analog to reset list in qca953x.dtsi
On startup the USB of QCA9531 board can't be initialized successfully.

lsusb result as below:
root@OpenWrt:~# lsusb unable to initialize libusb: -99

This is because usb-phy-analog is not added to reset list.

Signed-off-by: Jinfan Lei <153869379@qq.com>
(added linebreaks and small little changes to the commit message)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-29 22:55:16 +01:00
Nick Hainke
83b5fbddf2 kernel: 5.10: add patches to fix macronix flash
mtd: spi-nor: locking support for MX25L6405D

Macronix MX25L6405D supports locking with four block-protection bits.
Currently, the driver only sets three bits.  If the bootloader does not
sustain the flash chip in an unlocked state, the flash might be
non-writeable. Add the corresponding flag to enable locking support with
four bits in the status register.

mtd: spi-nor: disable 16-bit-sr for macronix

Macronix flash chips seem to consist of only one status register.
These chips will not work with the "16-bit Write Status (01h) Command".
Disable SNOR_F_HAS_16BIT_SR for all Macronix chips.

Refreshed:
- 0052-mtd-spi-nor-use-4-bit-locking-for-MX25L12805D.patch

Fixes: 15aa53d7ee ("ath79: switch to Kernel 5.10")

Signed-off-by: Nick Hainke <vincent@systemli.org>
2021-12-29 22:55:16 +01:00
WonJung Kim
2dde2416e1 ramips: add support for ipTIME A3004T
ipTIME A3004T is a 2.4/5GHz band router, based on Mediatek MT7621.

Specifications:
 - SoC: MT7621 (880MHz)
 - RAM: DDR3 256M
 - Flash: NAND 128MB  (Macronix NAND 128MiB 3,3V 8-bit)
 - WiFi:
   - 2.4GHz: MT7615E
   - 5GHz : MT7615E
 - Ethernet:
   - 4x LAN
   - 1x WAN
 - USB: 1 * USB3.0 port
 - UART:
   - 3.3V, TX, RX, GND / 57600 8N1

Installation via web interface:
 1. Flash initramfs image using OEM's Recovery mode
 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
 - Flash stock firmware via OEM's Recovery mode

How to use OEM's Recovery mode:
 1. Power up with holding down the reset key until CPU LED stop blinking.
 2. Set fixed ip with `192.168.0.2` with subnet mask `255.255.255.0`
 3. Flash image via tftp to `192.168.0.1`

Additional Notes:
 This router shares one MT7915E chip for both 2.4Ghz/5Ghz.
 radio0 will not working on 5Ghz as it's not connected to the antenna.

Signed-off-by: WonJung Kim <git@won-jung.kim>
(added led dt-bindings)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-29 20:35:57 +01:00
Sungbo Eo
482a7e23a4 ramips: add support for WeVO AIR DUO
WeVO AIR DUO is a 1-bay NAS & 802.11ac (Wi-Fi 5) router, based on
MediaTek MT7620A.

Specifications:
* SoC: MT7620A
* RAM: 64 MiB
* Flash: SPI NOR 16 MiB
* USB & SATA bridge controller: JMicron JMS567
  * SATA 6Gb/s: 2.5" drive slot
  * USB 3.0: Micro-B
  * USB 2.0: connected to SoC
* Wi-Fi:
  * 2.4 GHz: SoC built-in
  * 5 GHz: MT7612EN
* Ethernet: 5x 1GbE
  * Switch: MT7530WU
* UART: 4-pin 1.27 mm pitch through-hole (57600 baud)
  * Pinout: (3V3)|(RXD) (TXD) (GND)

Notes:
* The drive is accessible through the external USB port only when the
  router is turned off.

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
    The image filename should have ".upload" extension.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2021-12-29 20:35:57 +01:00
Torsten Duwe
7ea9936f7f bcm27xx: add AMP2 to HifiBerry DAC+ / DAC+ Pro package
According to the vendor [1] these HATs share the same DT overlay:
hifiberry-dacplus. The PCM512x-compatible control unit is attached to
I2C, so the additional snd-soc-pcm512x-i2c kernel module is required.
Also explicitly note the Amp2 support to reduce confusion for those
users.

[1] <https://www.hifiberry.com/docs/software/configuring-linux-3-18-x/>
Signed-off-by: Torsten Duwe <duwe@lst.de>
(added bcm27xx tag, changed commit message)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-29 20:35:57 +01:00
Pawel Dembicki
afd7ec3b57 kirkwood: add support for two clones from Endian
They are Endian 4i Edge 200 and his clone Endian UTM Mini.

Hardware:
  - SoC: Marvell 88F6281-A1 ARMv5TE Processor 1.2GHz
  - Ram: 512MB (4x Nanya NT5TU128M8GE-AC)
  - NAND Flash: 512MB (Micron 29F4G08AAC)
  - Lan 1-4: 4x GBE (Marvell 88E6171R-TFJ2)
  - Lan 5: 1x GBE (Marvell 88E1116R-NNC1)
  - Storage: MicroSD Slot
  - WLAN: MiniPCIe Slot present, and fitted with SparkLan WPEA-110N/E
          (Atheros AR9280 chipset) (ONLY Endian UTM Mini WLAN)
  - USB: 1x USB 2.0 port
  - Console: RJ-45 port
  - LEDs: 3x GPIO controlled

Notes:
  - WLAN led (Endian UTM Mini) is drived by MPCIE card

Installation by TFTP + serial:
  - Setup TFTP server and copy initramfs image
  - Connect serial console
  - Stop booting in u-boot
  - Do:
	setenv bootargs 'console=ttyS0,115200n8 earlyprintk'
	saveenv
	setenv serverip 192.168.1.1
	setenv ipaddr 192.168.1.2
	tftpboot 0x1200000 openwrt-kirkwood-endian_4i-edge-200-initramfs-uImage
	bootm 0x1200000
  - copy sysupgrade image via ssh.
  - run sysupgrade

Installation by USB + serial:
  - Copy initramfs image to fat32 usb drive
  - Connect pendrive to USB 2.0 front socket
  - Connect serial console
  - Stop booting in u-boot
  - Do:
	setenv bootargs 'console=ttyS0,115200n8 earlyprintk'
        saveenv
	usb reset
	fatload usb 0:1 0x1200000 openwrt-kirkwood-endian_4i-edge-200-initramfs-uImage
	bootm 0x1200000
  - copy sysupgrade image via ssh.
  - run sysupgrade

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2021-12-29 20:35:57 +01:00
Pawel Dembicki
4e46ae1f69 kirkwood: add support for NETGEAR ReadyNAS Duo v2
NETGEAR ReadyNAS Duo v2 is a NAS based on Marvell kirkwood SoC.

Specification:
 - Processor Marvell 88F6282 (1.6 GHz)
 - 256MB RAM
 - 128MB NAND
 - 1x GBE LAN port (PHY: Marvell 88E1318)
 - 1x USB 2.0
 - 2x USB 3.0
 - 2x SATA
 - 3x button
 - 5x leds
 - serial on J5 connector accessible from rear panel
   (115200 8N1) (VCC,TX,RX,GND) (3V3 LOGIC!)

Installation by USB + serial:
  - Copy initramfs image to fat32 usb drive
  - Connect pendrive to USB 2.0 front socket
  - Connect serial console
  - Stop booting in u-boot
  - Do:
	usb reset
        setenv bootargs 'console=ttyS0,115200n8 earlyprintk'
        setenv bootcmd 'nand read.e 0x1200000 0x200000 0x600000;bootm 0x1200000'
        saveenv
	fatload usb 0:1 0x1200000 openwrt-kirkwood-netgear_readynas-duo-v2-initramfs-uImage
	bootm 0x1200000
  - copy sysupgrade image via ssh.
  - run sysupgrade

Installation by TFTP + serial:
  - Setup TFTP server and copy initramfs image
  - Connect serial console
  - Stop booting in u-boot
  - Do:
	setenv bootargs 'console=ttyS0,115200n8 earlyprintk'
	setenv bootcmd 'nand read.e 0x1200000 0x200000 0x600000;bootm 0x1200000'
	saveenv
	setenv serverip 192.168.1.1
	setenv ipaddr 192.168.1.2
	tftpboot 0x1200000 openwrt-kirkwood-netgear_readynas-duo-v2-initramfs-uImage
	bootm 0x1200000
  - copy sysupgrade image via ssh.
  - run sysupgrade

Known issues:
  - Power button and PHY INTn pin are connected to the same GPIO. It
    causes that every network restart button is pressed in system.
    As workaround, button is used as regular BTN_1.

For more info please look at file:
RND_5.3.13_WW.src/u-boot/board/mv_feroceon/mv_hal/usibootup/usibootup.c
from Netgear GPL sources.

Tested-by: Raylynn Knight <rayknight@me.com>
Tested-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2021-12-29 20:35:57 +01:00
Pawel Dembicki
4e82a80b68 kernel: generic: backport linkstation-poweroff driver
Linkstation poweroff driver was added to mvebu target, but is required
for kirkwood target too.
This commit make two changes:
- move linkstation-poweroff support patch from mvebu to generic and
replace upstream accepted version
- backport small linkstation-poweroff fix from 5.12

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2021-12-29 20:35:57 +01:00
David Bauer
79a81d36ae ath79: remove pre-5.10 specific kernel code
With Kernel 5.4 support removed, we can get rid of this legacy code.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-12-29 03:44:56 +01:00
David Bauer
00b194871c ramips: aw9523: add can_sleep flag for GPIO chip
The GPIO expander is connected via I2C, thus the can_sleep flag has to
be set to true. This should fix spurious "scheduling while atomic" bugs
in the kernel ringbuffer.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-12-29 03:43:03 +01:00
Daniel Golle
92820cc5b9
mediatek: yet again, replace patch with updated pending patch
Upon comment of Russell King ('Oh no, not this "-1 disease" again.')
clean up mdio read and write return type and value in mtk_eth_soc
driver and also use appropriate return values for bus-busy-timeout-
errors in newly added Clause 45 access code.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-27 20:20:10 +00:00
Daniel Golle
c555c34dd1
mediatek: replace patch with version sent upstream
Replace recently added patch
 701-net-ethernet-mtk_eth_soc-add-support-for-clause-45-mdio.patch
with version sent upstream
 701-net-ethernet-mtk_eth_soc-implement-Clause-45-MDIO-access.patch

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-27 16:24:23 +00:00
Sergey Ryazanov
5deb3996e2 ath25: add kernel 5.10 support
Copy and refresh patches and config from 5.4 to 5.10. Most patches
require no more then automatic refresh. The only exception is the
Ethernet driver patch, which requires some more work:
* drop eth_change_mtu() usage since it was removed from the kernel,
  it anyway useless for drivers that utilizes alloc_etherdev();
* add the txqueue number argument to the .ndo_tx_timeout callback
  function;
* replace ioremap_nocache() which was finally removed from the kernel by
  the ioremap() with the same behaviour.

Switch target to the new kernel version.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[use KERNEL_TESTING_PATCHVER for now]
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2021-12-27 16:00:21 +00:00
Sergey Ryazanov
5bf8ae7c4b ath25: refresh kernel 5.4 config
The target config require some refresh due to the just introduced
filtering of the "run-time" options, MIPS eBPF JIT backporting, and so
on.

The configuration is easily updated using make kernel_oldconfig. So
let's update it now in preparation for v5.10 support to reduce the new
kernel configuration diff.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2021-12-27 16:00:21 +00:00
Sergey Ryazanov
0b2c1d8b9a Move mvswitch 88E6060 driver to the ath25
ath25 requires a 88E6060 driver to support boards such as Fonera 2.0g
(FON2202). The swconfig based mvswitch driver has not yet been ported to
the 5.10 kernel as the only user is the ath25 target while all other
targets have been switched to the upstream DSA implementation.

Switching ath25 to the DSA implementation is a complex task, since we
need either per-board platform data or DTS support. ath25 lacks both of
them and builds only a single generic image. So we need to keep the
swconfig driver implementation to easly and quickly port ath25 to the
5.10 kernel.

Since porting the mvswitch driver to 5.10 as a generic driver is not an
option, and since the ath25 is its only user, make mvswitch a target
specific driver to be able to port it to the 5.10 kernel as part of the
kernel version update of the target. This will allow us quickly migrate
to the next kernel version and not delay the next firmware release.

Suggested-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2021-12-27 16:00:21 +00:00
Rui Salvaterra
a3774d72c8 kernel: bump 5.10 to 5.10.88
Deleted (upstreamed):
mpc85xx/patches-5.10/002-powerpc-85xx-fix-oops-when-CONFIG_FSL_PMC-n.patch [1]

[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.88&id=151ffac3ac277ad7c2a5f201b566b56d97ed3a99

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-12-27 16:00:21 +00:00
Christian Lamparter
0e841fd4a2 apm821xx: remove broken PCIe MSI support
These never worked and upstream is in the process of removing
them as well. Legacy PCI interrupt signaling is still working
as before.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-27 13:55:10 +01:00
Christian Lamparter
4e6ebdd7ce apm821xx: remove overlapping partitions
Apart from the dtb partition, these were all "read-only;"
they serve no purpose other than being a copy of what
netgear had defined in their original firmware.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-27 13:55:10 +01:00
Christian Lamparter
832b9cbd74 apm821xx: fix WD MyBook Live DUO USB-Port
where to begin? the USB regulator settings were just
a part of the issue. With them changed, according to
the forum it still failed when a USB device was
connected to the port with:

dwc2 4bff80000.usbotg: dwc2_restore_global_registers: no global registers to restore
dwc2 4bff80000.usbotg: dwc2_exit_partial_power_down: failed to restore registers
dwc2 4bff80000.usbotg: exit partial_power_down failed
dwc2 4bff80000.usbotg: HC died; cleaning up

One clue was found upstream in
commit cc10ce0c51b1 ("usb: dwc2: disable power_down on Amlogic devices")

|Disable power_down by setting the parameter to
|DWC2_POWER_DOWN_PARAM_NONE. This fixes a problem on various Amlogic
|Meson SoCs where USB devices are only recognized when plugged in before
|booting Linux. A hot-plugged USB device was not detected even though the
|device got power (my USB thumb drive for example has an LED which lit
|up).
|[...]

the same method proposed there worked with APM821xx's USB IP-Core.

Link: https://forum.openwrt.org/t/wd-my-book-duo-usb/111926/2
Reported-by: thwe and takimata (openwrt forum)
Fixes: b70d3557e0 ("apm821xx: clean up gpio-hogs")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-27 13:55:10 +01:00
Christian Lamparter
2593d510e2 apm821xx: drop 5.4 config and patches
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-27 13:51:41 +01:00
Sander Vanheule
ebc0ce118f realtek: netgear-gs110tpp: Add system LEDs
The GS110TPP has an RGB LED used for system status indication. Expose
all three components as separate GPIO LEDs connected via the device's
RTL8231.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2021-12-27 13:51:41 +01:00
Sander Vanheule
c88124cfc4 realtek: netgear-gigabit: Enable RTL8231
Since the move to 5.10, there are now two GPIO drivers. The gpio0 node
refers to the internal GPIOs, so the indirect-access-bus-id is no longer
relevant for that node.

Set indirect-access-bus-id to the correct value (31) on the correct node
(gpio1) and enable the device.

Cc: Raylynn Knight <rayknight@me.com>
Cc: Michael Mohr <akihana@gmail.com>
Cc: Stijn Segers <foss@volatilesystems.org>
Cc: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Bjørn Mork <bjorn@mork.no>
2021-12-27 13:51:41 +01:00
Ansuel Smith
5761aa4d9e kernel: mtd: parsers: add nvmem support to cmdlinepart
Assuming cmdlinepart is only one level deep partition scheme and that
static partition are also defined in DTS, we can assign an of_node for
partition declared from bootargs.

The cmdlinepart parser is the first parser checked and if it does find
some partition declared in the bootargs, every other parser is ignored.
This means that the fixed-partition parser is ignored and an of_node for
the mtd is never assigned.
Fix this by searching a defined of_node using a similar fixed_partition
parsing logig, check if a partition is present with the same label, check
that it has the same offset and size and finally assign an of_node to the
mtd. The NVMEM can now find the of_node for the mtd and correctly works.

Fixes: abc17bf306 ("ath79: convert mtd-mac-address to nvmem implementation")
Tested-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2021-12-27 13:51:41 +01:00
David Bauer
e1780de5ce rockchip: remove Kernel 5.4
As v5.10 is the default kernel version now, the files for v5.4 can be
dropped.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-12-27 03:13:36 +01:00
David Bauer
13f326de3a mpc85xx: remove kernel 5.4
As v5.10 is the default kernel version now, the files for v5.4 can be
dropped.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-12-27 03:13:36 +01:00
David Bauer
9d9d851eec ath79: remove kernel 5.4
Signed-off-by: David Bauer <mail@david-bauer.net>
2021-12-27 03:13:36 +01:00
Nick Hainke
cfa670bf16 ath79: add missing UBNT_REVISION
The UBNT_REVISION was already added for the ubnt-xw target because:

  U-boot bootloader on M-XW devices expects factory image revision
  version in specific format. On airOS v6.1.7 with `U-Boot 1.1.4-s1039
  (May 24 2017 - 15:58:18)` bootloader checks if the revision major(?)
  number is actually a number, but in currently generated images there's
  OpenWrt text and so the check fails

  ...

  By placing arbitrary correct number first in major version, we make the
  bootloader happy and we can flash factory images over TFTP again.

  commit d42a7c4699 ("ath79: ubnt-m-xw: Fix factory image flashing using TFTP recovery method")

Fixes errors in the form of (tftp flashing):
  sent DATA <block=8577, 412 bytes>
  received ERROR <code=2, msg=Firmware check failed>
  Error code 2: Firmware check failed

The missing UBNT_REVISION was not noticed before, since the
UBNT_REVISION field for the ubnt-xm target was also set to:
  "42.OpenWrt-..."
Probably, UBNT_REVISION for the ubnt-xm target was set by the ubnt-xw
and was never overridden somewhere else. However, it is missing and
should be part of the ubnt-xm device.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2021-12-27 03:07:22 +01:00
Hauke Mehrtens
0dc4ab344b sunxi: Use rtl8723bu-firmware instead of rtl8723bs-firmware
The firmware for the rtl8723bs chip is now included in the
rtl8723bu-firmware package.

Fixes: 397dfe4a97 ("linux-firmware: Update to version 20121216")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-12-27 00:58:29 +01:00
Daniel Golle
8b6d6f28c1
mediatek: mt7622: unifi6lr: properly register Ethernet PHY
This change enables proper Ethernet link status and speed reporting on
the Ubiquiti UniFi 6 LR access point:

 mtk_soc_eth 1b100000.ethernet eth0: PHY [mdio-bus:08] driver [Aquantia AQR112C] (irq=POLL)
 mtk_soc_eth 1b100000.ethernet eth0: configuring for phy/2500base-x link mode
 mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-26 19:11:54 +00:00
Daniel Golle
e6c08c8272
mediatek: mt7622: enable driver for Aquantia PHYs
Enable Aquantia Ethernet PHY driver as there is an AQR112C 2500Base-T
PHY in the Ubiquiti UniFi 6 LR access point.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-26 19:11:49 +00:00
Daniel Golle
13b3474294
mediatek: add support for Clause 45 MDIO access
Add support for Clause 45 MDIO PHY register read and write operations
to mtk_eth_soc driver.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-26 19:11:43 +00:00
Daniel Golle
215c78eef5
kernel: generic: refresh patch
722-net-phy-aquantia-Add-AQR113-driver-support.patch needs refresh.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-26 19:11:36 +00:00
Rafał Miłecki
65974aa18b bcm4908: include ATF in bootfs images
It's required for proper booting.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-12-24 23:07:39 +01:00
Daniel Golle
f9782f5bcd
mvebu: puzzle: wan LED and fix default network
Fix default network configuration of the Puzzle-M902 so all LAN ports
are included in the LAN bridge.
Setup network LED to indicate WAN port link status, like vendor
firmware does as well.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-23 20:17:47 +00:00
Daniel Golle
f81a06408e
mvebu: enable Aquantia phy driver for Puzzle devices
Fixes Ethernet link status on all ports and makes 2.5G ports usable
in 2.5G and 1G full-duplex mode.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-23 20:17:42 +00:00
Daniel Golle
7b9d2d6f7b
kernel: add id for AQR112 Ethernet phy variants
Add ids for AQR112R and AQR112C 2.5G Ethernet PHYs.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-23 20:17:37 +00:00
Daniel Golle
73c0ef1ecf
kernel: import patch enabling AQR113 PHY
Add PHY ID for the Aquantia AQR113 PHY.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-23 20:17:32 +00:00
Daniel Golle
6563a6a3ba
kernel: import patch enabling AQR112 and AQR412 PHY
Copy and refresh patch enabling AQR112 and AQR412 Ethernet PHY from
layerscape (5.4) target to generic (5.10) as AQR112 can also be found
on other targets as well.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-23 20:17:28 +00:00
Daniel Golle
962c585580
mvebu: remove accidentally added file
Remove accidentally added file (which was a left-over of a by-now
replaced driver)

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-21 23:44:45 +00:00
Daniel Golle
3684b494dd
mvebu: puzzle-m901: add LEDs, fan and reset button
Wire up MCU driver for LEDs, fan and temperature sensor, and add
GPIO reset button just like on the M902 also on the Puzzle M901.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-21 21:54:54 +00:00
Daniel Golle
ddad936fc6
mvebu: puzzle-m902: add GPIO reset button
Add reset button to device tree so it has the function expected from
usual OpenWrt devices.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-21 21:54:49 +00:00
Daniel Golle
7e4c1cca8a
mvebu: puzzle-mcu: improve led driver
Set blinking mode using scheduled work instead of blocking which may
result in deadlocks.
Add dynamic kprintf debugging hexdumps of all MCU rx and tx.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-21 21:54:42 +00:00
Paul Spooren
15aa53d7ee ath79: switch to Kernel 5.10
Kernel 5.10 is used by many people since quite a while. With other
targets already moved to 5.10, let ath79 follow suit.

Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ath79/tl-wdr3600; ath79/tl-wdr4300]
Tested-by: Aleksander Jan Bajkowski <olek2@wp.pl> [ath79/tl-wdr4300]
Signed-off-by: Paul Spooren <mail@aparcar.org>
Signed-off-by: David Bauer <mail@david-bauer.net>
2021-12-21 21:38:52 +01:00
Stijn Tintel
3fda16078b qoriq: add support for WatchGuard Firebox M300
This device is based on NXP's QorIQ T2081QDS board, with a quad-core
dual-threaded 1.5 GHz ppc64 CPU and 4GB ECC RAM. The board has 5
ethernet interfaces, of which 3 are connected to the ethernet ports on
the front panel. The other 2 are internally connected to a Marvell
88E6171 switch; the other 5 ports of this switch are also connected to
the ethernet ports on the front panel.

Installation: write the sdcard image to an SD card. Stock U-Boot will
not boot, wait for it to fail then run these commands:

setenv OpenWrt_fdt image-watchguard-firebox-m300.dtb
setenv OpenWrt_kernel watchguard_firebox-m300-kernel.bin
setenv wgBootSysA 'setenv bootargs root=/dev/mmcblk0p2 rw rootdelay=2 console=$consoledev,$baudrate fsl_dpaa_fman.fsl_fm_max_frm=1530; ext2load mmc 0:1 $fdtaddr $OpenWrt_fdt; ext2load mmc 0:1 $loadaddr $OpenWrt_kernel; bootm $loadaddr - $fdtaddr'
saveenv
reset

The default U-Boot boot entry will now boot OpenWrt from the SD card.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-12-21 21:37:46 +02:00
Stijn Tintel
080a769b4d qoriq: new target
Add a new target named "qoriq", that will support boards using PowerPC
processors from NXP's QorIQ brand.

This doesn't actually add support for any board yet, so that
installation instructions can go in the commit message of the commit
that adds actual support for a board.

Using CONFIG_E6500_CPU here due to the kernel using -mcpu=powerpc64
rather than -mcpu=e5500 when selecting CONFIG_E5500_CPU. The only
difference between e5500 and e6500 is AltiVec support, and the kernel
checks for it at runtime. Musl will only check at runtime if AltiVec
support is disabled at compile-time, so we need to use e5500 in CPU_TYPE
to avoid SIGILL.

Math emulation (CONFIG_MATH_EMULATION_HW_UNIMPLEMENTED) is required, as
neither e5500 nor e6500 implement fsqrt nor fsqrts, and musl hardcodes
sqrt and sqrtf to use these ASM instructions on PowerPC64.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reviewed-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-12-21 21:37:39 +02:00
Daniel Golle
f0c0b18234
mvebu: puzzle-m902: add driver for MCU driving LEDs, fan and buzzer
Backport MFD driver for communicating with the on-board MCU found on
IEI World Puzzle appliances.
Improve the driver to support multiple LEDs, apply a default state and
let MCU take care of blinking if timing is within supported range.
Wire up LEDs and fan for Puzzle M902 in device tree.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-21 16:41:10 +00:00
David Bauer
b1d483b865 ramips: work around duplicate MAC address on U6 Lite
The UniFi 6 Lite has two MAC addresses for the 2.4 and 5GHz radio in
it's EEPROM partition.

On my unit these are

F4 92 BF A0 BB 6F
F6 92 BF A0 BB 6F

The problem with these is that mac80211 increases the first octet by
2, which leads to conflicting MAC addresses between radios.

Work around this problem for now by increasing the last octet by 1 on
the 5 GHz radio.

Ubiquiti increases the last octet by 2 for each subsequent VAP created
per radio. Ideally we should do the same, however this functionality is
currently lacking from mac80211.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-12-20 00:12:12 +01:00
Daniel Golle
5a4685cfa2
mediatek: mt7623: bpi-r2: add ethernet alias to device tree
Add ethernet0 alias in device tree to make U-Boot inherit the Ethernet
mac address (set via environment variable 'ethaddr') down to Linux.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-18 01:52:19 +00:00
Sergey Ryazanov
fa3690f8f1 kernel: 5.10: consolidate mac80211 crypto options
Each of
- CRYPTO_AEAD2
- CRYPTO_AEAD
- CRYPTO_GF128MUL
- CRYPTO_GHASH
- CRYPTO_HASH2
- CRYPTO_HASH
- CRYPTO_MANAGER2
- CRYPTO_MANAGER
- CRYPTO_NULL2

either directly required for mac80211 crypto support, or directly
selected by such options. Support for the mac80211 crypto was enabled in
the generic config since c7182123b9 ("kernel: make cryptoapi support
needed by mac80211 built-in"). So move the above options from the target
configs to the generic config to make it clear why do we need them.

CC: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2021-12-17 16:16:34 +01:00
Sergey Ryazanov
b61ab8f57e kernel: filter out both Clang and LLD versions
Both CLANG_VERSION and LLD_VERISON are autogenerated runtime
configuration options, so add them to the kernel configuration filter
and remove from generic and per-target configs to keep configs clean.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2021-12-17 16:16:34 +01:00
John Audia
43c0a12665 kernel: bump 5.10 to 5.10.85
Removed target for patch which does not exist:
    bcm27xx/patches-5.10/950-0249-kbuild-Disable-gcc-plugins.patch

All patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, ipq806x/R7800*
Run-tested: bcm2711/RPi4B, ipq806x/R7800*

* Had to revert 7f1edbd412 in order to build
  (binutils 2.37, https://bugs.openwrt.org/index.php?do=details&task_id=4149)

Signed-off-by: John Audia <graysky@archlinux.us>
2021-12-17 15:10:22 +01:00
John Audia
187c8f9153 kernel: bump 5.10 to 5.10.84
All patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B
Run-tested: bcm2711/RPi4B

Signed-off-by: John Audia <graysky@archlinux.us>
2021-12-17 15:10:22 +01:00
John Audia
d4b25007ea kernel: bump 5.4 to 5.4.167
All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/mt7621*

*FS#4149 affects me so I had to revert 7f1edbd412
in order to downgrade to 2.35.1

Signed-off-by: John Audia <graysky@archlinux.us>
2021-12-17 15:10:22 +01:00
John Audia
61c76f836f kernel: bump 5.4 to 5.4.166
All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/mt7621*

*FS#4149 affects me so I had to revert 7f1edbd412
in order to downgrade to 2.35.1

Signed-off-by: John Audia <graysky@archlinux.us>
2021-12-17 15:10:22 +01:00
John Audia
a696e325f7 kernel: bump 5.4 to 5.4.165
All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/mt7621*

*FS#4149 affects me so I had to revert 7f1edbd412
in order to downgrade to 2.35.1

Signed-off-by: John Audia <graysky@archlinux.us>
2021-12-17 15:10:22 +01:00
Sungbo Eo
cc3e390a74 ramips: mt7620: tidy up 02_network
* fix alphabetic sorting
* consolidate duplicate cases

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2021-12-16 22:28:58 +09:00
Rafał Miłecki
444b4ea4a4 bcm4908: add uboot-envtools to default packages
It's required by sysupgrade to access UBI metadata partitions.

Fixes: 5f05795aa7 ("bcm4908: sysupgrade: add pkgtb format support")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-12-16 08:26:25 +01:00
Rafał Miłecki
85ad48c957 kernel: backport support for multicolor & RGB LEDs to 5.4
This is a requirement for backporting DT files defining such LEDs.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-12-16 07:18:05 +01:00
Felix Fietkau
01bebc070c kernel: backport the upstream implementation of threaded NAPI to 5.4
The workqueue based implementation has a few corner cases and typically lower
performance than the upstream one

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-12-15 20:36:22 +01:00
Rui Salvaterra
c772783394 ramips: remove Linux 5.4 support
We're at 5.10 stable, this can finally go.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-12-15 09:40:03 +00:00
David Bauer
07452a680b ramips: fix Tenbay T-MB5EU v1 Wireless MAC
It was reported, that Tenbay T-MB5EU v1 do have incorrect Wireless MAC
address set on 2.4 and 5 GHz.

Some boards do not seem to have the correct MAC address set for the
external PHY of the MT7915 radio at caldata offset 0xa.

As the external PHY does not expose a DT binding (yet), fix up the mac
address in userspace.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-12-15 00:13:40 +01:00
Rafał Miłecki
30b93672ec bcm4908: add fdt-utils to default packages
It's required by sysupgrade.

Fixes: 5f05795aa7 ("bcm4908: sysupgrade: add pkgtb format support")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-12-14 17:58:20 +01:00
Martin Schiller
60881f657d layerscape: armv7: refresh config-5.10
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2021-12-13 23:22:29 +01:00
Martin Schiller
7af83d2c03 layerscape: armv7: copy config-5.4 to config-5.10
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2021-12-13 23:22:29 +01:00
Martin Schiller
fef79a5dc4 layerscape: armv8_64b: refresh config-5.10
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2021-12-13 23:22:29 +01:00
Martin Schiller
a939015dd1 layerscape: armv8_64b: copy config-5.4 to config-5.10
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2021-12-13 23:22:29 +01:00
Martin Schiller
83035a44a7 layerscape: armv8_64b: use non-SDK dts files for linux-5.10 or newer
Since we decided to drop the LSDK patches with linux-5.10, we now have
to switch to the corresponding upstream dts files as well.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2021-12-13 23:22:29 +01:00
Martin Schiller
82ce460ab1 layerscape: armv8_64b: fix KERNEL_LOADADDR for linux >= 5.8
In kernel versions newer than 5.8 the arm64 TEXT_OFFSET (0x80000) has
been set to 0x0 (and later removed). This will break Uimages with kernel
load addresses that aren't 2MiB aligned any longer. Resulting in the
kernel silently fail to boot. For layerscape armv8_64b targets this
needs to be changed to 0x80000000 (start of RAM).

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2021-12-13 23:22:29 +01:00
Martin Schiller
68b4e9fe0e layerscape: add patches for kernel 5.10
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2021-12-13 23:22:29 +01:00
Martin Schiller
7e35d86ca2 layerscape: add kernel 5.10 as testing version
This patch adds "KERNEL_TESTING_PATCHVER:=5.10" to the Makefile in
layerscape target to allow using Kernel 5.10 for testing.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2021-12-13 23:22:29 +01:00
Martin Schiller
0a9454918d layerscape: remove unneeded KERNEL_ENTRY_POINT definition
As KERNEL_ENTRY_POINT is identical to KERNEL_LOADADDR, drop it.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2021-12-13 23:22:29 +01:00
Rui Salvaterra
66f9ed1684 ramips: switch to kernel 5.10
Tested on mt7621 (Redmi AC2100) and running stable for several months.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Tested-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
2021-12-13 19:36:52 +01:00
Pawel Dembicki
794e8123ce ramips: mt7620: use OKLI loader with Jboot devices
Jboot devices have problem with >2MB kernelsize. The only way to avoid
this problem is use small loader.

This patch switch all mt7620 Jboot devices to lzma OKLI loader.

Suggested-by: Szabolcs Hubai <szab.hu@gmail.com>
Co-authored-by: Michael Pratt <mcpratt@pm.me>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2021-12-13 19:36:10 +01:00
Rafał Miłecki
3bcf3e8143 bcm53xx: sysupgrade: fix support for Luxul's legacy firmware format
Fixes: 80041dea70 ("bcm53xx: sysupgrade: refactor handling different firmware formats")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-12-13 18:19:35 +01:00
Rafał Miłecki
5f05795aa7 bcm4908: sysupgrade: add pkgtb format support
BCM4908 devices with U-Boot use pkgtb firmware format. It's based on
U-Boot's FIT: DTB with configurations, images & embedded data.

This format contains bootfs, rootfs and optionally a first stage U-Boot
loader. Contained images need to be extracted & flashed.

Broadcom used two sets of firmwares: main & backup. It uses UBI volumes
"metadata1" & "metadata2" for storing U-Boot env variables with info
about flashed images.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-12-13 08:53:00 +01:00
Moritz Warning
59faf41da1 treewide: use uniform vendor value for british telecom
British Telecom is mostly known as BT.

Signed-off-by: Moritz Warning <moritzwarning@web.de>
2021-12-12 21:11:38 +01:00
John Audia
6c945fa379 kernel: bump 5.10 to 5.10.83
Removed upstreamed:
    bcm53xx/patches-5.10/033-v5.16-0024-ARM-dts-BCM5301X-Fix-I2C-controller-interrupt.patch[1]
    bcm53xx/patches-5.10/033-v5.16-0025-ARM-dts-BCM5301X-Add-interrupt-properties-to-GPIO-no.patch[2]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.83&id=b2cd6fdcbe0a5cb44e4610a08cc58261d494a885
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.83&id=9db1d4a3c2700e1cc84c3d61199411d75c2a3ec6

Build system: x86_64*
Build-tested: bcm2711/RPi4B, ipq806x/R7800†
Run-tested: bcm2711/RPi4B, ipq806x/R7800†

* Had to revert 7c99085bd6 in order to build
  (latest bump of ca-certificates)

† Had to revert 7f1edbd412 in order to build
  (binutils 2.37, https://bugs.openwrt.org/index.php?do=details&task_id=4149)

Signed-off-by: John Audia <graysky@archlinux.us>
2021-12-12 21:11:30 +01:00
Enrico Mioso
a725bdc700 ipq40xx: fix reset button GPIO for GL.iNet GL-B2200
GL.iNet's U-Boot checks for GPIO 40, not 43.
Changing this allows the RESET button to work as expected.

Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
CC: Daniel Golle <daniel@makrotopia.org>
CC: Li Zhang <li.zhang@gl-inet.com>
2021-12-12 19:14:16 +00:00
Kyoungkyu Park
9a1b9a42b7 ramips: add support for HUMAX E10
HUMAX E10 (also known as HUMAX QUANTUM E10) is a 2.4/5GHz band AC router,
based on MediaTek MT7621A.

Specifications:
- SoC: MT7621A
- RAM: DDR3 128MB
- Flash: SPI NOR 16MB (MXIC MX25L12805D)
- WiFi:
  - 2.4GHz: MT7615
  - 5GHz: MT7615
- Ethernet: 2x 10/100/1000Mbps
  - Switch: SoC internal
- USB: 1x USB 2.0 Type-A
- UART: J1 (57600 8N1)
  - pinout: [3V3] (RXD) (GND) (TXD)

Installation via web interface:
- Flash **factory** image through the stock web interface.

Recovery procedure:
1. Connect ethernet cable between Router **LAN** port and PC Ethernet port.
2. Set your computer to a static IP **192.168.1.1**
3. Turn the device off and wait a few seconds. Hold the WPS button on front
   of device and insert power.
4. Send a firmware image to **192.168.1.6** using TFTP.
   You can use any TFTP client. (tftp, curl, Tftpd64...)
- It can accept both images which is
  HUMAX stock firmware dump (0x70000-0x1000000) image
  and OpenWRT **sysupgrade** image.

Signed-off-by: Kyoungkyu Park <choryu.park@choryu.space>
[remove trailing whitespace]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2021-12-12 20:33:19 +09:00
Sungbo Eo
91e37b60a0 ramips: mt76x8: tidy up 02_network
* fix alphabetic sorting
* consolidate duplicate cases

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2021-12-12 20:25:56 +09:00
Felix Fietkau
3b20eb185b kernel: fix RCU issue in xt_FLOWOFFLOAD patch
cond_resched() may not be called in a rcu-locked section

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-12-11 13:52:39 +01:00
Christian Lamparter
b2aca5a263 ath79: fix various dts warnings
ar9344_openmesh_mr600-v1.dts:40.10-44.5: Warning (gpios_property):
/leds-ath9k/wifi2g: Missing property '#gpio-cells' in node
/ahb/pcie-controller@180c0000/wifi@0,0 or bad phandle
=> added gpio-controller + #gpio-cells

qca955x_zyxel_nbg6x16.dtsi:121.3-13: Warning (reg_format):
/ahb/usb@1b000000/port@1:reg: property has invalid length (4 bytes)
(#address-cells == 2, #size-cells == 1)
../dts/qca955x_zyxel_nbg6x16.dtsi:131.3-13: Warning (reg_format):
/ahb/usb@1b400000/port@1:reg: property has invalid length (4 bytes)
(#address-cells == 2, #size-cells == 1)
qca955x_zyxel_nbg6x16.dtsi:120.20-123.4: Warning (avoid_default_addr_size):
/ahb/usb@1b000000/port@1: Relying on default #address-cells value
=> ath79's usb-nodes are missing the address- and size-cells properties.
These are needed for usb led trigger support.

ar7242_ubnt_sw.dtsi:54.4-14: Warning (reg_format): /gpio_spi/gpio_spi@0:reg:
property has invalid length (4 bytes) (#address-cells == 1, #size-cells == 1)
=> the #address-cells and #size-cells had to be nudged.

qca9531_dlink_dch-g020-a1.dts:19.6-39.4: Warning (i2c_bus_bridge):
/i2c: incorrect #size-cells for I2C bus
=> #size-cells = <0>;

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-11 00:50:02 +01:00
Joel Linn
7061d5f343 lantiq: fixed wifi support for AVM FRITZ!Box 7430
adds the correct offset for the calibration data.
The values are according to the OpenWrt Forum Thread:
"Fritzbox 7430 and wifi".

Link: <https://forum.openwrt.org/t/fritzbox-7430-and-wifi/86944>
Reported-by: RENErica
Signed-off-by: Joel Linn <jl@conductive.de>
[changed commit message]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-11 00:50:02 +01:00
Ryan Mounce
35aecc9d4a ath79: add support for WD My Net N600
SoC: AR9344
RAM: 128MB
Flash: 16MiB SPI NOR
5GHz WiFi: AR9382 PCIe 2x2:2 802.11n
2.4GHz WiFi: AR9344 (SoC) AHB 2x2:2 802.11n

5x Fast ethernet via SoC switch (green LEDs)
1x USB 2.0
4x front LEDs from SoC GPIO
1x front WPS button from SoC GPIO
1x bottom reset button from SoC GPIO

UART header JP1, 115200 no parity 1 stop
TX
GND
VCC
(N/P)
RX

Flash factory image via "emergency room" recovery:
- Configure your computer with a static IP 192.168.1.123/24
- Connect to LAN port on the N600 switch
- Hold reset putton
- Power on, holding reset until the power LED blinks slowly
- Visit http://192.168.1.1/ and upload OpenWrt factory image
- Wait at least 5 minutes for flashing, reboot and key generation
- Visit http://192.168.1.1/ (OpenWrt LuCI) and upload OpenWrt sysupgrade image

Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
[dt leds preparations]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-11 00:50:02 +01:00
Olivier Valentin
7853453950 ath79: add support for jjPlus JWAP230
The jjPlus JWAP230 is an access point board built around the QCA9558,
with built-in 2.4GHz 3x3 N WiFi (28dBm). It can be expanded with 2
mini-PCIe boards, and has an USB2 root port.

Specifications:
- SOC: Qualcomm Atheros QCA9558
- CPU: 720MHz
- H/W switch: QCA8327 rev 2
- Flash: 16 MiB SPI NOR (en25qh128)
- RAM: 128 MiB DDR2
- WLAN: AR9550 built-in SoC bgn 3T3R (ath9k)
- PCI: 2x mini-PCIe (optional 5V)
- LEDs: 6x LEDs (3 are currently available)
- Button: 1x Reset (not yet defined)
- USB2:
  - 1x Type A root port
  - 1x combined mini-PCIe
- Ethernet:
  - 2x 10/100/1000 (1x PoE 802.3af (36-57 V))

Notes:
 The device used to be supported in the ar71xx target.
 For upgrades: Please use "sysupgrade --force -n <image>".
 This will restore the device back to OpenWrt defaults!

MAC address assignment:
    use   source
    LAN   art 0x0
    WAN   art 0x6
    WLAN  art 0x1002 (as part of the calibration data)

Flash instructions:
- install from u-boot with tftp (requires serial access)
  > setenv ipaddr a.b.c.d
  > setenv serverip e.f.g.h
  > tftp 0x80060000 \
      openwrt-ath79-generic-jjplus_jwap230-squashfs-sysupgrade.bin
  > erase 0x9f050000 +${filesize}
  > cp.b $fileaddr 0x9f050000 $filesize
  > setenv bootcmd bootm 0x9f050000
  > saveenv

Signed-off-by: Olivier Valentin <valentio@free.fr>
[Added DT-Leds (based on ar71xx), Added more notes about sysupgrade,
fixed "qca9550" to match SoC in commit and dts file name]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-11 00:50:02 +01:00
Christian Lamparter
4deaeaa13c x86: remove old lzma tuning patch
Chen Minqiang reported in his GitHub PR #4733 that:
With CONFIG_TARGET_INITRAMFS_COMPRESSION_LZMA=y option set,
the popular x86/amd64 target's initramfs-kernel failed to boot.

The cause for this boot failure is that the LZMA compression
uses a the first bytes to encode the compression parameters.
It does not have a fixed magic. Yes, this only works if the
the existing lzma options in the upstream are not changed.

This patch does away with OpenWrt special LZMA options tuning
since it is rather unlikely that upstream will improve the
compression algorithm detection after all this time. Even
though, the tuning produced a smaller initramfs (~1.1% in a
spot check).

Link: <https://github.com/openwrt/openwrt/pull/4733>
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-11 00:50:02 +01:00
Stan Grishin
ffab23d99d x86: add/improve support for Sophos SG/XG products
* Better product ID for Sophos SG/XG-105 models
* Add support for Sophos SG/XG-135 r1, r2 with/without wireless

Signed-off-by: Stan Grishin <stangri@melmac.ca>
[Changed subject to x86 - probably eaten somewhere, the PR had it]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-11 00:50:02 +01:00
Josef Schlehofer
1c4b3ce344 kernel: add more disabled config options
NET_DSA_MSCC_FELIX:

Marvell 88E6xxx Ethernet switch fabric support (NET_DSA_MV88E6XXX) [N/m/y/?] n
Ocelot / Felix Ethernet switch support (NET_DSA_MSCC_FELIX) [N/m/y/?] (NEW)
Error in reading or end of file.

make[6]: *** [scripts/kconfig/Makefile:71: syncconfig] Error 1
make[5]: *** [Makefile:603: syncconfig] Error 2

IR_IMON_RAW:
    SoundGraph iMON Receiver (early raw IR models) (IR_IMON_RAW) [N/m/?] (NEW)

Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
[squashed with "kernel: add missing IR_IMON_RAW config symbol"]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-11 00:49:36 +01:00
Sergey Ryazanov
7e89421a7c ramips: add support for Zbtlink ZBT-WG1602
Zbtlink ZBT-WG1602 is a Wi-Fi router intendent to use with WWAN
(UMTS/LTE/3G/4G) modems. The router board offsers a couple of miniPCIe
slots with USB and SIM only and another one pure miniPCIe slot as well
as five Gigabit Ethernet ports (4xLAN + WAN).

Specification:

* SoC: MT7621A
* RAM: 256/512 MiB
* Flash: 16/32 MiB (SPI NOR)
* external watchdog (looks like Torexsemi XC6131B)
* Eth: 10/100/1000 Mbps Ethernet x5 ports (4xLAN + WAN)
* WLAN 2GHz: MT7603EN (.11n, MIMO 2x2)
* WLAN 5GHz: MT7612EN (.11ac, MIMO 2x2)
* WLAN Ants: detachable x2, shared by 2GHz & 5GHz radios
* miniPCIe: 2x slots with USB&SIM + 1x slot with regular PCIe bus
* WWAN Ants: detachable x4
* External storage: microSD (SDXC) slot
* USB: 2.0 Type-A port
* LED: 11 (5 per Eth phy, 3 SoC controlled, 2 WLAN 2/5 controlled, 1
       power indicator)
* Button: 1 (reset)
* UART: console (115200 baud)
* Power: DC jack (12 V / 2.5 A)

Additional HW information:

* SoC USB port #1 is shared by internal miniPCIe slot and external
  Type-A USB port, USB D+/D- lines are toggled between ports using a
  GPIO controlled DPDT switch.
* Power of the USB enabled miniPCIe slots can be individually controlled
  using dedicated GPIO lines.
* Vendor firmware feeds the external watchdog with 1s pulses. GPIO
  watchdog driver is able to either generate a 1us pulses or toggle the
  output line. 1us is not enough for the external watchod timer, so
  the line toggling driver mode is utilized.

Installation:

Vendor's firmware is OpenWrt (LEDE) based, so the sysupgrade image can
be directly used to install OpenWrt. Firmware must be upgraded using the
'force' and 'do not save configuration' command line options (or
correspondig web interface checkboxes) since the vendor firmware is from
the pre-DSA era.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2021-12-05 18:49:14 +01:00
Sander Vanheule
0f6b6aab2b ath79: add support for TP-Link EAP225 v1
TP-Link EAP225 v1 is an AC1200 (802.11ac Wave-1) ceiling mount access point.

Device specifications:
* SoC: QCA9563 @ 775MHz
* RAM: 128MiB DDR2
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (SoC): b/g/n, 2x2
* Wireless 5Ghz (QCA9882): a/n/ac, 2x2
* Ethernet (AR8033): 1× 1GbE, 802.3at PoE

Flashing instructions:
* Ensure the device is upgraded to firmware v1.4.0
* Exploit the user management page in the web interface to start telnetd
  by changing the username to `;/usr/sbin/telnetd -l/bin/sh&`.
* Immediately change the malformed username back to something valid
  (e.g. 'admin') to make ssh work again.
* Use the root shell via telnet to make /tmp world writeable (chmod 777)
* Extract /usr/bin/uclited from the device via ssh and apply the binary
  patch listed below. The patch is required to prevent `uclited -u` in
  the last step from crashing.
* Copy the patched uclited binary back to the device at /tmp/uclited
  (via ssh)
* Upload the factory image to /tmp/upgrade.bin (via ssh)
* Run `chmod +x /tmp/uclited && /tmp/uclited -u` to install OpenWrt.

uclited patching:
    --- xxd uclited
    +++ xxd uclited-patched
    @@ -53811,7 +53811,7 @@
     000d2330: 8c44 0000 0320 f809 0000 0000 8fbc 0010  .D... ..........
     000d2340: 8fa6 0a4c 02c0 2821 8f82 87c4 0000 0000  ...L..(!........
    -000d2350: 8c44 0000 0c13 461c 27a7 0018 8fbc 0010  .D....F.'.......
    +000d2350: 8c44 0000 2402 0000 0000 0000 8fbc 0010  .D..$...........
     000d2360: 1040 001d 0000 1821 8f99 8378 3c04 0058  .@.....!...x<..X
     000d2370: 3c05 0056 2484 ad68 24a5 9f00 0320 f809  <..V$..h$.... ..

To make sure the correct file is patched, the following MD5 checksums
should match the unpatched and patched files:
    4bd74183c23859c897ed77e8566b84de  uclited
    4107104024a2e0aeaf6395ed30adccae  uclited-patched

Debricking:
* Serial port can be soldered on unpopulated 4-pin header
  (1: TXD, 2: RXD, 3: GND, 4: VCC)
    * Bridge unpopulated resistors running from pins 1 (TXD) and 2 (RXD).
      Do NOT bridge the pull-down for pin 2, running parallel to the
      header.
    * Use 3.3V, 115200 baud, 8n1
* Interrupt bootloader by holding CTRL+B during boot
* tftp initramfs to flash via the LuCI web interface
    setenv ipaddr 192.168.1.1 # default, change as required
    setenv serverip 192.168.1.10 # default, change as required
    tftp 0x80800000 initramfs.bin
    bootelf $fileaddr

Tested by forum user KernelMaker.

Link: https://forum.openwrt.org/t/eap225-v1-firmware/87116
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2021-12-05 18:49:14 +01:00
Bjørn Mork
afeda4a3d3 realtek: sort the port list numerically
Mac adresses are assigned in the order given by the port list.  The
interfaces are also brought up in this order.  This target supports
devices with up to 52 ports.  Sorting these alphabetically is very
confusing, and assigning mac addresses in alphabetic order does not
match stock firmware behaviour.

Suggested-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-12-05 18:49:14 +01:00
Sander Vanheule
4304799b4a realtek: update watchdog timer patch
The Realtek Otto watchdog timer driver was accepted upstream, and is
queued for 5.17. Update the patch's file name, and replace by the final
version.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2021-12-05 18:49:14 +01:00
Oldřich Jedlička
fd4ad6cae8 x86: added support to generate VHDX images
Added support to generate dynamic-sized VHDX images for Hyper-V.
Compile-tested on x86 and run-tested on Windows 10 21H2 (Hyper-V).

Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
2021-12-05 18:49:14 +01:00
Shane Synan
9f0575a130 ipq806x: revert SDC clock changes for NBG6817 MMC
Revert the SDC "CLK_SET_RATE_GATE" changes to the SDC clock regulator
structures.

See https://elinux.org/images/b/b8/Elc2013_Clement.pdf
> if ((clk->flags & CLK_SET_RATE_GATE) && clk->prepare_count) {
>
> For this particular clock, setting its rate is possible only if the
> clock is ungated (not yet prepared)

This fixes the MMC failing to initialize on newer ZyXEL NBG6817
hardware revisions with Kingston MMC.  Older revisions should
hopefully be unaffected.

Check MMC hardware details with:
cd /sys/block/mmcblk0/device/ && \
  tail -v cid date name manfid fwrev hwrev oemid rev

Known problematic MMC names (broken before this commit):
* M62704 (dated 12/2018) via myself
* M62704 (dated 11/2018) via Drake Stefani

Known unaffected MMC names (already working without this commit):
* S10004 (dated 12/2015) via slh

Without enabling dynamic debugging, this error manifests in the kernel
hardware serial console as the following:

[    2.746605] mmc0: error -110 whilst initialising MMC card
[…trimmed other messages…]
[    2.877832] Waiting for root device /dev/mmcblk0p5...

Enabling Linux dynamic kernel debugging provides additional messages.
For guidance, see the Linux kernel documentation:
https://www.kernel.org/doc/html/latest/admin-guide/dynamic-debug-howto.html

First, enable dynamic debugging in OpenWRT's configuration:

1.  Run "make menuconfig"

2.  Select "Global build settings --->"

3.  Select "Kernel build options --->"

4.  Enable "Compile the kernel with dynamic printk" via spacebar

5.  Save and exit (arrow key to "Exit" until prompted to save, save)

Alternatively, set "CONFIG_KERNEL_DYNAMIC_DEBUG=y" in your .config.

Then, turn on dynamic debugging at boot:

Modify bootargs in
target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts
to add…

bootargs = "[…existing bootargs…] dyndbg=\"file drivers/mmc/* +p\" dynamic_debug.verbose=1 loglevel=8";

For example:
 	chosen {
-		bootargs = "rootfstype=squashfs,ext4 rootwait noinitrd fstools_ignore_partname=1";
+		bootargs = "rootfstype=squashfs,ext4 rootwait noinitrd fstools_ignore_partname=1 dyndbg=\"file drivers/mmc/* +p\" dynamic_debug.verbose=1 loglevel=8";
 		append-rootblock = "root=/dev/mmcblk0p";

Then, compile and flash the resulting build.  If you are testing
before this commit on newer MMC hardware, be prepared to recover!

NOTE: If you have hardware serial console access, you don't need to
use TFTP recovery to change the active boot partition.

Reboot to working alternative partition via serial console:

1.  Connect to hardware serial console
    * See https://openwrt.org/toh/zyxel/nbg6817#serial

2.  Interrupt boot at "Hit any key to stop autoboot:"

3.  Run "ATSE NBG6817"

4.  Copy the result (e.g. "001976FE4B04")
    * Changes with **every boot** - can't reuse this

5.  On your local system, run
    "./zyxel-uboot-password-tool.sh <copied value here>"
    * Example: "./zyxel-uboot-password-tool.sh 001976FE4B04"

6.  Run the command provided by the password tool
    * Example: "ATEN 1,910F129B"
    * Changes with **every boot** - can't reuse this

7.  Run "ATGU"
    * You now have full u-boot shell until next boot - unlocking is
       not remembered

8.  Run either "run boot_mmc" (for booting partition set "FF") or
    "run boot_mmc_1" (for booting partition set "01")
    * These commands are not affected by dual-boot partition flags

NOTE: This will NOT set the dual-boot partition flag.  You'll need to
fix that manually.  The "nbg6817-dualboot" script may help:
https://github.com/pkgadd/nbg6817/blob/master/nbg6817-dualboot

zyxel-uboot-password-tool.sh - sourced from
commit 459c8c9ef8:

ror32() {
  echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) ))
}

v="0x$1"
a="0x${v:2:6}"
b=$(( a + 0x10F0A563))
c=$(( 0x${v:12:14} & 7 ))
p=$(( $(ror32 $b $c) ^ a ))
printf "ATEN 1,%X\n" $p

Kernel serial console log BEFORE commit with dynamic debug enabled:
[…trimmed…]
[    3.171343] mmci-pl18x 12400000.sdcc: designer ID = 0x51
[    3.171397] mmci-pl18x 12400000.sdcc: revision = 0x0
[    3.175811] mmci-pl18x 12400000.sdcc: clocking block at 96000000 Hz
[    3.181134] mmci-pl18x 12400000.sdcc: No vqmmc regulator found
[    3.186788] mmci-pl18x 12400000.sdcc: mmc0: PL180 manf 51 rev0 at 0x12400000 irq 41,0 (pio)
[    3.192902] mmci-pl18x 12400000.sdcc: DMA channels RX dma1chan1, TX dma1chan2
[    3.215609] mmc0: clock 0Hz busmode 2 powermode 1 cs 0 Vdd 21 width 1 timing 0
[    3.227532] mmci-pl18x 12400000.sdcc: Initial signal voltage of 3.3v
[    3.247518] mmc0: clock 52000000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 1 timing 0
[…trimmed…]
[    3.997725] mmc0: req done (CMD2): -110: 00000000 00000000 00000000 00000000
[    4.003631] mmci-pl18x 12400000.sdcc: irq0 (data+cmd) 00000000
[    4.003659] mmc0: error -110 whilst initialising MMC card
[    4.016481] mmc0: clock 0Hz busmode 2 powermode 0 cs 0 Vdd 0 width 1 timing 0

Notice how the initial clock is 52 MHz, which is incorrect - MMC
requires negotiation to enable higher speeds.

Kernel serial console log AFTER commit with dynamic debug enabled:
[…trimmed…]
[    3.168996] mmci-pl18x 12400000.sdcc: designer ID = 0x51
[    3.169051] mmci-pl18x 12400000.sdcc: revision = 0x0
[    3.173492] mmci-pl18x 12400000.sdcc: clocking block at 96000000 Hz
[    3.178808] mmci-pl18x 12400000.sdcc: No vqmmc regulator found
[    3.184702] mmci-pl18x 12400000.sdcc: mmc0: PL180 manf 51 rev0 at 0x12400000 irq 41,0 (pio)
[    3.190573] mmci-pl18x 12400000.sdcc: DMA channels RX dma1chan1, TX dma1chan2
[    3.217873] mmc0: clock 0Hz busmode 2 powermode 1 cs 0 Vdd 21 width 1 timing 0
[    3.229250] mmci-pl18x 12400000.sdcc: Initial signal voltage of 3.3v
[    3.249111] mmc0: clock 400000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 1 timing 0
[…trimmed…]
[    4.392652] mmci-pl18x 12400000.sdcc: irq0 (data+cmd) 00000000
[    4.392785] mmc0: clock 52000000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 1 timing 1
[    4.406554] mmc0: starting CMD6 arg 03b70201 flags 0000049d
[…trimmed…]

Now, the MMC properly initializes and later switches to high speed.

Thanks to:
* Ansuel for maintaining/help with the IPQ806x platform, kernel code
* slh for additional debugging and suggestions
* dwfreed for confirming newer MMC details, clock frequency
* robimarko for device driver debug printing help, clock debugging
* Drake for testing and confirmation with their own newer NBG6817
...and anyone else I missed!

Signed-off-by: Shane Synan <digitalcircuit36939@gmail.com>
Tested-by: Shane Synan <digitalcircuit36939@gmail.com>
2021-12-05 18:49:14 +01:00
Felix Fietkau
f9a28d216d mediatek: enable bmt on mt7622-rfb1
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-12-04 22:47:17 +01:00
Chuanhong Guo
2d49e49b18 mediatek: bmt: use generic mtd api
BMT replaces nand-specific ops for erasing and writing, but the
mtk-snand driver only implements generic mtd api.

Replace erase, block_isbad, block_markbad in mtd_info for generic mtd
drivers.

Fixes: b600aee3ed ("mediatek: attach bmt to the new snand driver")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2021-12-04 22:47:17 +01:00
Yuchan Seo
c33eb0372e ramips: add support for ipTIME A3004NS-dual
ipTIME A3004NS-dual is a 2.4/5GHz band router, based on Mediatek MT7621.

Specifications:
- SoC: MT7621 (880MHz)
- RAM: DDR3 256M
- Flash: SPI NOR 16MB
- WiFi:
 - 2.4GHz: MT7602E
 - 5GHz : MT7612E
- Ethernet:
 - 4x LAN
 - 1x WAN
- USB: 1 * USB3.0 port
- UART:
  - 3.3V, TX, RX, GND / 57600 8N1

Installation via web interface:
- 1. Flash Initramfs image using OEM Firmware's web GUI
- 2. Boot into OpenWrt and perform Sysupgrade with sysupgrade image.

Revert to stock firmware:
- 1. Boot into OpenWrt and perform Sysupgrade with OEM Stock Firmware image.

Signed-off-by: Yuchan Seo <hexagonwin@disroot.org>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
2021-12-04 09:39:11 +09:00
Pawel Dembicki
3843c641d8 kirkwood: add support for Ctera C200 V1 NAS
2-Bay NAS - maximum two 3.5" Harddisks

Hardware:
  - SoC: Marvell 88F6281-A1 ARMv5TE Processor 1.2GHz
  - Ram: 512MB (4x Nanya NT5TU128M8GE-AC)
  - NAND Flash: 256MB (Samsung 216 K9F2G08U0C)
  - Lan: 1x GBE (Marvell 88E1116R-NNC1)
  - Storage: 2x SATA HDD 3.5" Slot
  - USB: 2x USB 2.0 port
  - Console: Internal J3 connector (1: Vcc, 2: Rx, 3: Tx, 4: GND)
  - LEDs: 13x GPIO controlled
  - Buttons: 2x GPIO controlled

Known issues:
  - Buzzer is unused due lack of proper driver

Installation:
  - Apply factory initramfs image via stock web-gui.
  - Do sysupgrade to make installation complete.

Back to stock:
  - OpenWrt rootfs partition use unused space after stock firmware.
  - Full revert is possible.
  - Login via ssh and run: ctera_c200-v1_back_to_factory

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
[apply sorting to device recipe]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2021-12-04 09:39:11 +09:00
Sergey V. Lobanov
e22c91e144 ramips: fix tl-mr3020-v3 switch topology to configure vlans via luci
Currently it is not possible to configure VLANs via LUCI on
tplink tl-mr3020-v3. This patch fixes switch topology for the
LUCI interface.

Signed-off-by: Sergey V. Lobanov <sergey@lobanov.in>
[copied commit message from github PR]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-04 00:36:47 +01:00
Pawel Dembicki
a82fa5bcd4 ramips: mt7620: Enable PHY aneg of Lava LR-25G001
In 20b09a2125 Lava LR-25G001 router have problem with two inactive
ethernet ports. JBOOT bootloader didn't configure ethernet devices by default.
The same situation was there. It is required to enable all phy ports.
This is fragment of stock bootlog:

switch reg write_athr offset=90, value=2b0
switch reg write_athr offset=8c, value=2b0
switch reg write_athr offset=88, value=2b0
switch reg write_athr offset=84, value=2b0
switch reg write_athr offset=80, value=2b0

This patch adds proper registers configuration ar8337 initvals.
0x2b0 value causes force flow control configuration, 0x1200 was used
instead (flow control config auto-neg with phy). [1]

When switch is now ok, let's fix port numeration too.

Fixes: 20b09a2125 ("ramips: add support for Lava LR-25G001")

[1] https://github.com/openwrt/openwrt/pull/4806#issuecomment-982019858

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2021-12-04 00:36:47 +01:00
Christian Lamparter
d641a60478 ipq40xx: nvmem cells for EZVIZ CS-W3-WD1200G EUP
introduce nvmem pre-cal + mac-address cells for both Wifis
and ethernet on the EZVIZ CS-W3-WD1200G EUP. This is one of
the few devices in which the correct mac adress is already
at the right place for Wifi, so no separate nvmem cell is
needed.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-04 00:36:47 +01:00
Christian Lamparter
45eb57f12f ipq40xx: unbreak EZVIZ CS-W3-WD1200G EUP on 5.10
with current images, the device is no longer booting.
It gets stuck in the bootloader with "Config not available"
and drops to the uboot shell.

|flash_type: 0
|Hit any key to stop autoboot:  0
|SF: Detected MX25L12805D with page size 4 KiB, total 16 MiB
|Config not availabale
|(IPQ40xx) #

This is because the default bootcmd "bootipq" will only read
the first four MiB of the kernel image. With 5.10 the gzip'd
kernel is slightly larger. So the part of the FIT image which
had the configuration is cut off. Hence it can't find it.

To update the bootcmd, you have to attach the serial console
again and enter the following commands into the boot prompt:

 # setenv bootcmd "sf probe; sf read 84000000 180000 600000; bootm"
 # saveenv
 # run bootcmd

This will allow booting kernels with up to six MiB. This also
allows us to drop the DEVICE_DTS_CONFIG hack we had to use.

Note:
uboot doesn't support LZMA. It fails with:
"Unimplemented compression type 3"

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-04 00:36:47 +01:00
Christian Lamparter
eb20a1b8bb gemini: only provide squashfs image for storlink-derivates
The itian sq201, raidsonic ib-4220-b and storlink sl93512r
can't boot from ext4. This is because the rootfstype in the
device-tree bootargs is set to "squashfs,jffs2". (And ext4
was not designed for raw NOR flash chips).

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-04 00:36:47 +01:00
Kabuli Chana
7fd1ca96a1 mvebu: next backport mvnet MQPrio offload
linux-next MQPrio patches adding TC traffic shaping offload

Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
2021-12-03 12:35:23 +01:00
Catrinel Catrinescu
24d455d1d0 ath79: add Embedded Wireless Balin Platform
Add the Embedded Wireless "Balin" platform, it is in ar71xx too
 SoC: QCA AR9344 or AR9350
 RAM: DDR2-RAM 64MBytes
 Flash: SPI-NOR 16MBytes
 WLAN: 2 x 2 MIMO 2.4 & 5 GHz IEEE802.11 a/b/g/n
 Ethernet: 3 x 10/100 Mb/s
 USB: 1 x USB2.0 Host/Device bootstrap-pin at power-up
 PCIe: MiniPCIe - 1 x lane PCIe 1.2
 Button: 1 x Reset-Button
 UART: 1 x Normal, 1 x High-Speed
 JTAG: 1 x EJTAG
 LED: 1 x Green Power/Status LED
 GPIO: 10 x Input/Output multiplexed

The module comes already with the current vanilla OpenWrt firmware.
To update, use "sysupgrade -n --force <image>" image directly in
vendor firmware. This resets the existing configurations back to
default!

Signed-off-by: Catrinel Catrinescu <cc@80211.de>
[indent, led function+color properties, fix partition unit-address,
re-enable pcie port, mention button+led in commit message]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-03 12:30:08 +01:00
Bjørn Mork
8ac8c09f5e ipq40xx: sysupgrade: drop disabled UBI to UBI logic
The commented out code is not required, as the comment
indicates.

The purpose of this code seems to be to avoid issues caused
by partially overwriting an existing UBI partition, where some
of the erase counters would be reset but not the unmodified
ones.  This problem has been solved in a more generic way by
the UBI EOF marker. This ensures that any old PEBs after the
marker are properly initialized.  It is therefore unnecessary
to erase the whole partition before flashing a new OpenWrt
factory image.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-12-03 12:23:02 +01:00
Bjørn Mork
5fb51d4516 ipq806x: sysupgrade: drop unnecessary UBI to UBI logic
The purpose of this code seems to be to avoid issues caused
by partially overwriting an existing UBI partition, where some
of the erase counters would be reset but not the unmodified
ones.  This problem has been solved in a more generic way by
the UBI EOF marker. This ensures that any old PEBs after the
marker are properly initialized.  It is therefore unnecessary
to erase the whole partition before flashing a new OpenWrt
factory image.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-12-03 12:23:02 +01:00
Bjørn Mork
25382dff85 kirkwood: sysupgrade: drop unnecessary UBI to UBI logic
The purpose of this code seems to be to avoid issues caused
by partially overwriting an existing UBI partition, where some
of the erase counters would be reset but not the unmodified
ones.  This problem has been solved in a more generic way by
the UBI EOF marker. This ensures that any old PEBs after the
marker are properly initialized.  It is therefore unnecessary
to erase the whole partition before flashing a new OpenWrt
factory image.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-12-03 12:23:02 +01:00
Bjørn Mork
0efb169aad mvebu: sysupgrade: drop unnecessary UBI to UBI logic
The recent changes to the maximum kernel size for Mamba and Venom
highlighted the fact that the old Mamba kernel size has been
hardcoded in linksys_get_root_magic() even for devices with
a different kernel/rootfs split.

The purpose of this code seems to be to avoid issues caused
by partially overwriting an existing UBI partition, where some
of the erase counters would be reset but not the unmodified
ones.  This problem has been solved in a more generic way by
the UBI EOF marker. This ensures that any old PEBs after the
marker are properly initialized.  It is therefore unnecessary
to erase the whole partition before flashing a new OpenWrt
factory image.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-12-03 12:23:02 +01:00
Daniel Golle
c47e82d255
mediatek: mt7623: switch to BPi-R2 to generic eMMC sysugprade
Make use of new functions in emmc.sh to implement sysupgrade on the
BananaPi BPi-R2.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-02 20:43:17 +00:00
Daniel Golle
c9db3ed58e
mediatek: mt7622: switch to generic eMMC sysupgrade
Use functions in newly introduced emmc.sh for sysupgrade of the
BananaPi BPi-R64.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-02 20:43:12 +00:00
TruongSinh Tran-Nguyen
febc2b831f
ipq40xx: add support for GL.iNet GL-B2200
This patch adds supports for the GL-B2200 router.

Specifications:
  - SOC: Qualcomm IPQ4019 ARM Quad-Core
  - RAM: 512 MiB
  - Flash: 16 MiB NOR - SPI0
  - EMMC: 8GB EMMC
  - ETH: Qualcomm QCA8075
  - WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11b/g/n 2x2
  - WLAN2: Qualcomm Atheros QCA4019 5GHz 802.11n/ac W2 2x2
  - WLAN3: Qualcomm Atheros QCA9886 5GHz 802.11n/ac W2 2x2
  - INPUT: Reset, WPS
  - LED: Power, Internet
  - UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1
  - UART2: On board with BLE module
  - SPI1: On board socket for Zigbee module

Update firmware instructions:
Please update the firmware via U-Boot web UI (by default at 192.168.1.1, following instructions found at
https://docs.gl-inet.com/en/3/troubleshooting/debrick/).
Normal sysupgrade, either via CLI or LuCI, is not possible from stock firmware.
Please do use the *gl-b2200-squashfs-emmc.img file, gunzipping the produced *gl-b2200-squashfs-emmc.img.gz one first.

What's working:
- WiFi 2G, 5G
- WPA2/WPA3

Not tested:
- Bluetooth LE/Zigbee

Credits goes to the original authors of this patch.

V1->V2:
- updates *arm-boot-add-dts-files.patch correctly (sorry, my mistake)
- add uboot-envtools support
V2->V3:
- Li Zhang updated official patch to fix wrong MAC address on wlan0 (PCI) interface
V3->V4:
- wire up sysupgrade

Signed-off-by: Li Zhang <li.zhang@gl-inet.com>
[fix tab and trailing space, document what's working and what's not]
Signed-off-by: TruongSinh Tran-Nguyen <i@truongsinh.pro>
[rebase on top of master, address remaining comments]
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
[remove redundant check in platform.sh]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-02 20:43:07 +00:00
Enrico Mioso
57c1f3f9c5
base-files: add eMMC sysupgrade support
Adds generic support for sysupgrading on eMMC-based devices.

Provide function emmc_do_upgrade and emmc_copy_config to be used in
/lib/upgrade/platform.sh instead of redundantly implementing the same
logic over and over again.
Similar to generic sysupgrade on NAND, use environment variables
CI_KERNPART, CI_ROOTPART and newly introduce CI_DATAPART to indicate
GPT partition names to be used. On devices with more than one MMC
block device, CI_ROOTDEV can be used to specify the MMC device for
partition name lookups.

Also allow to select block devices directly using EMMC_KERN_DEV,
EMMC_ROOT_DEV and EMMC_DATA_DEV, as using GPT partition names is not
always an option (e.g. when forced to use MBR).

To easily handle writing kernel and rootfs make use of sysupgrade.tar
format convention which is also already used for generic NAND support.

Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
CC: Li Zhang <li.zhang@gl-inet.com>
CC: TruongSinh Tran-Nguyen <i@truongsinh.pro>
2021-12-02 20:42:58 +00:00
Alexander Couzens
8d62304785
ipq40xx: add MikroTik LHGG-60ad outdoor 802.11ad (60GHz) dish
LHGG-60ad is IPQ4019 + wil6210 based.

Specification:

- Qualcomm IPQ4019 (717 MHz)
- 256 MB of RAM (DDR3L)
- 16 MB (SPI NOR) of flash
- 1x Gbit ethernet, 802.3af/at POE IN connected through AR8035.
- WLAN: wil6210 802.11ad PCI card
- No USB or SD card ports
- UART disabled
- 8x LEDs

Biggest news is the wil6210 PCI card.
Integration for its configuration and detection has already been taken
care of when adding support for TP-Link Talon AD7200.
However, signal quality is much lower than with stock firmware, so
probably additional board-specific data has to be provided to the
driver and is still missing at the moment.

Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[Fix Ethernet Interface]
Signed-off-by: Nick Hainke <vincent@systemli.org>
2021-12-02 19:46:14 +00:00
Michel Promonet
fd311a5fe3 sunxi: update nanopi neo air that use brcmfmac43430a0
Update wifi firmware used for nanopi neo air, with
cypress-firmware-43430-sdio there is no wifi detected, as
brcmfmac-firmware-43430a0-sdio allow to acces to wifi.

Signed-off-by: Michel Promonet <michel.promonet@free.fr>
2021-12-02 10:58:36 +00:00
Rafał Miłecki
30b168b9b8 bcm4908: sysupgrade: refactor handling different firmware formats
This results in setting format specific data (format info, extract
commands) in a single function. It should help maintaining sysupgrade
code.

This change has been tested on Asus GT-AC5300 and Netgear R8000P.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-12-02 09:17:43 +01:00
Rafał Miłecki
80041dea70 bcm53xx: sysupgrade: refactor handling different firmware formats
List of supported formats grew over time and implementation got a bit
messy. There are multiple functions with format-specific parameters and
commands.

Refactor it by making platform_identify() setup all required info right
after detecting firmware format. This simplifies formats handling in
platform_other_check_image() and platform_do_upgrade() a lot.

This has been tested on:
1. SmartRG SR400ac (TRX): non-NAND sysupgrade
2. Netgear R8000 (CHK): NAND aware and standard sysupgrade-s
3. D-Link DIR-885L (Seama): NAND aware and standard sysupgrade-s
4. Luxul XWR-3150 (LXL): NAND aware and standard sysupgrade-s

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-12-02 09:15:18 +01:00
Rafał Miłecki
e7bd6cce4c bcm53xx: sysupgrade: simplify extracting image from Seama seal
Use "oseama extract" which supports now writing to stdout.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-12-02 09:15:18 +01:00
Aleksander Jan Bajkowski
56246f2910 lantiq: xway_legacy: disable unused switches
The xway_legacy subtarget only supports 5 devices. Most compiled
switch drivers are unused by any of these devices. The same drivers
are compiled into the xway subtarget. They were probably copied
from there when creating this subtarget.

Switches used by devices:
Arcadyan ARV4518PWR01   Realtek RTL8306SD
Arcadyan ARV4518PWR01A  Realtek RTL8306SD
Arcadyan ARV4520PW      Infineon ADM6996I
Arcadyan ARV4525PW      only PHY(IC+ IP101A)
Arcadyan ARV452CQW      Realtek RTL8306

The CONFIG_ETHERNET_PACKET_MANGLE symbol has also been disabled,
as it is only needed by the driver for AR8216.

Reduces kernel size by 19.9 kB.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2021-11-30 22:29:24 +01:00
Martin Kennedy
79ceea4303 mpc85xx: Fix HiveAP-330 nvmem mac loader
We actually need to enclose the whole section of partitions in a
`partitions { ... }` to assign it a `compatible = "fixed-partitions";
otherwise the partition referred to by `hwinfo` won't be registered
when bringing up MTD partitions, for example as per:

- <https://forum.openwrt.org/t/tp-link-c2600-missing-default-mac-mtd-partition-in-snapshot/103945/6>

- commit e2b03c16eb ("ipq806x: add missing enclosing partitions block for TP-Link C2600")'

Fixes: 8ec21d6bb2 ("mpc85xx: convert mtd-mac-address to nvmem implementation")
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
[minor beautification]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-11-30 22:29:24 +01:00
Hauke Mehrtens
101300b842 bcm4908: Deactivate pci feature
This target does not activate CONFIG_PCI kernel configuration option, do
not activate the PCI feature. This will deactivate some PCI drivers
which are not building without PCI support in the kernel.

If PCI_SUPPORT or PCIE_SUPPORT are activated in the kernel configuration
the feature flag will be automatically set by the build system again.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-11-29 22:40:44 +01:00
Hauke Mehrtens
be3fcd72e9 kernel: Deactivate B53 symbols in generic configuration
Deactivate all the symbols of the B53 DSA driver in the generic kernel
configuration. Multiple targets are now using this drivers and they
only need some of the options.
This fixes the bcm4908 build which didn't deactivate all of the options.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-11-29 22:37:58 +01:00
Chukun Pan
001bdd5f67 sunxi: remove kmod-rtc-sunxi for unsupported devices
From driver source:

	{ .compatible = "allwinner,sun4i-a10-rtc", .data =
	&data_year_param[0] },
	{ .compatible = "allwinner,sun7i-a20-rtc", .data =
	&data_year_param[1] },

The rtc-sunxi module only supports allwinner a10 and a20 SoCs,
other SoCs in the cortexa7 and cortexa53 subtarget using the
CONFIG_RTC_DRV_SUN6I driver which is compiled into the kernel
binary, so remove this package for these unsupported devices.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2021-11-29 22:11:29 +01:00
Sander Vanheule
22f85d63cf realtek: netgear-gigabit: Add gpio-restart node
The Netgear GS110TPP v1 switch cannot reliably perform cold reboots
using the system's internal reset controller.

On this device, and the other supported Netgear switches, internal GPIO
line 13 is connected to the system's hard reset logic. Expose this GPIO
on all systems to ensure restarts work properly.

Cc: Raylynn Knight <rayknight@me.com>
Cc: Michael Mohr <akihana@gmail.com>
Cc: Stijn Segers <foss@volatilesystems.org>
Cc: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Bjørn Mork <bjorn@mork.no>
2021-11-28 22:43:08 +01:00
Sander Vanheule
3f4d6da453 realtek: Enable gpio-restart driver
Add the gpio-restart driver to the realtek build. This way devices,
which cannot reliably perform resets using the SoC's internal reset
logic, can use a GPIO line to drive the SoC's hard reset input.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2021-11-28 22:43:08 +01:00
Sander Vanheule
fa71139776 realtek: add missing GPIO irq properties
The internal GPIO controller on RTL838x is also an IRQ controller, which
requires the 'interrupt-controller' and '#interrupts-cells' properties
to be present in the device tree.

Reported-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2021-11-28 22:43:08 +01:00
Bjørn Mork
d1464afe1b realtek: use full range of assigned MAC addresses
Some devices are assigned globally unique MAC addresses for all
ports. These are stored by U-Boot in the second U-Boot enviroment
("sysinfo") as a range of start and end address.

Use the full range if provided.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-11-28 22:43:08 +01:00
Bjørn Mork
9e7149f729 realtek: revert to "standard" management configuration
The default management interface should be easy to find for users
doing "blind" installations without console access.  There are
already multiple examples in the forum of advanced early adopters
having problems locating the management interface after installing
OpenWrt.

Requiring tagged VLAN configration to access the initial management
interface creates unnecessary hassle at best. Errors on the other
end are close to impossible to debug without console access, even
for advanced users.  Less advanced users might have problems with
the concept of VLAN tagging.

Limiting management access to a single arbitrary port among up to
52 possible LAN ports makes this even more difficult, for no
reason at all. Users might have reasons to use a different port
for management.  And they might even have difficulties using the
OpenWrt selected one. The port might be the wrong type for their
management link (e.g copper instead of fibre).  Or they might
depend on PoE power from a device which they can't reconfigure.

User expectations will be based on
- OpenWrt defaults for other devices
- stock firmware default for the device in question
- common default behaviour of similar devices

All 3 cases point to a static IP address accessible on the native
VLAN of any LAN port.  A switch does not have any WAN port.  All
ports are LAN ports.

This changes the default network configuration in line with these
expectations.

Cc: John Crispin <john@phrozen.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-11-28 22:33:57 +01:00
Hauke Mehrtens
889043a155 uboot-omap: Remove omap3_overo configuration
The configs/omap3_overo_defconfig file was removed from upstream U-Boot
in commit ed3294d6d1f9 ("arm: Remove overo board"). Remove it in OpenWrt
too. If someone needs this please add it also to upstream U-Boot.

This fixes the compile of the omap target.

Fixes: ffb807ec90 ("omap: update u-boot to 2021.07")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-11-28 22:26:27 +01:00
Hauke Mehrtens
2f6c847eb7 kernel: Add extra kernel configuration options for omap
This fixes the build on omap.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-11-28 19:12:53 +01:00
Felix Matouschek
1cc3b95efc ipq40xx: Add support for Teltonika RUTX10
This patch adds support for the Teltonika RUTX10.
This device is an industrial DIN-rail router with 4 ethernet ports,
2.4G/5G dualband WiFi, Bluetooth, a USB 2.0 port and two GPIOs.

The RUTX series devices are very similiar so common parts of the DTS
are kept in a DTSI file. They are based on the QCA AP-DK01.1-C1 dev
board.

See https://teltonika-networks.com/product/rutx10 for more info.

Hardware:
  SoC:                 Qualcomm IPQ4018
  RAM:                 256MB DDR3
  SPI Flash 1:         XTX XT25F128B (16MB, NOR)
  SPI Flash 2:         XTX XT26G02AWS (256MB, NAND)
  Ethernet:            Built-in IPQ4018 (SoC, QCA8075), 4x 10/100/1000 ports
  WiFi 1:              Qualcomm QCA4019 IEEE 802.11b/g/n
  Wifi 2:              Qualcomm QCA4019 IEEE 802.11a/n/ac
  USB Hub:             Genesys Logic GL852GT
  Bluetooth:           Qualcomm CSR8510 (A10U)
  LED/GPIO controller: STM32F030 with custom firmware
  Buttons:             Reset button
  Leds:                Power (green, cannot be controlled)
                       WiFi 2.4G activity (green)
                       WiFi 5G activity (green)

MACs Details verified with the stock firmware:
   eth0:             Partition 0:CONFIG Offset: 0x0
   eth1:             = eth0 + 1
   radio0 (2.4 GHz): = eth0 + 2
   radio1 (5.0 GHz): = eth0 + 3
Label MAC address is from eth0.

The LED/GPIO controller needs a separate kernel driver to function.
The driver was extracted from the Teltonika GPL sources and can be
found at following feed: https://github.com/0xFelix/teltonika-rutx-openwrt

USB detection of the bluetooth interface is sometimes a bit flaky. When
not detected power cycle the device. When the bluetooth interface was
detected properly it can be used with bluez / bluetoothctl.

Flash instructions via stock web interface (sysupgrade based):
  1. Set PC to fixed ip address 192.168.1.100
  2. Push reset button and power on the device
  3. Open u-boot HTTP recovery at http://192.168.1.1
  4. Upload latest stock firmware and wait until the device is rebooted
  5. Open stock web interface at http://192.168.1.1
  6. Set some password so the web interface is happy
  7. Go to firmware upgrade settings
  8. Choose
     openwrt-ipq40xx-generic-teltonika_rutx10-squashfs-nand-factory.ubi
  9. Set 'Keep settings' to off
  10. Click update, when warned that it is not a signed image proceed

Return to stock firmware:
  1. Set PC to fixed ip address 192.168.1.100
  2. Push reset button and power on the device
  3. Open u-boot HTTP recovery at http://192.168.1.1
  4. Upload latest stock firmware and wait until the device is rebooted

Note: The DTS expects OpenWrt to be running from the second rootfs
partition. u-boot on these devices hot-patches the DTS so running from the
first rootfs partition should also be possible. If you want to be save follow
the instructions above. u-boot HTTP recovery restores the device so that when
flashing OpenWrt from stock firmware it is flashed to the second rootfs
partition and the DTS matches.

Signed-off-by: Felix Matouschek <felix@matouschek.org>
2021-11-28 18:39:01 +01:00
Matthew Hagan
67f5201276 ipq806x: add support for Cisco Meraki MR42/MR52
The MR42 and MR52 are two similar IPQ806x based devices from the Cisco
Meraki "Cryptid" series.

  MR42 main features:
  -  IPQ8068 1.4GHz
  -  512MB RAM
  -  128MB NAND
  -  2x QCA9992 (2.4 & 5GHz)
  -  1x QCA9889 (2.4 & 5GHz)
  -  1x AR8033 PHY
  -  PoE/AC power

  MR52 main features:
  -  IPQ8068 1.4GHz
  -  512MB RAM
  -  128MB NAND
  -  2x QCA9994 (2.4 & 5GHz)
  -  1x QCA9889 (2.4 & 5GHz)
  -  2x AR8033 PHYs
  -  PoE/AC power

(MR42 Only) Installation via diagnostic mode:

If you can successfully complete step 1 then you can continue to install
via this method without having to open the device. Otherwise please use
the standard UART method. Please note that when booting via TFTP, some
Ethernet devices, in particular those on laptops, will not connect in
time, resulting in TFTP boot not succeeding. In this instance it is
advised to connect via a switch.

  1. Hold down reset at power on and keep holding, after around 10 seconds
     if the orange LED changes behaviour to begin flashing, proceed to
     release reset, then press reset two times. Ensure that the LED has
     turned blue. Note that flashing will occur on some devices, but it
     will not be possible to change the LED colour using the reset button.
     In this case it will still be possible to continue with this install
     method.

  2. Set your IP to 192.168.1.250. Set up a TFTP server serving
     mr42_u-boot.mbn and
     openwrt-ipq806x-generic-meraki_mr42-initramfs-fit-uImage.itb, obtained
     from [1].

  3. Use telnet and connect to 192.168.1.1. Run the following commands to
     install u-boot. Note that all these commands are critical, an error
     will likely render the device unusable.

     Option 3.1:
       If you are sure you have set up the TFTP server correctly you can
       run this script on the device. This will download and flash the
       u-boot image immediately:

       `/etc/update_uboot.sh 192.168.1.250 mr42_u-boot.mbn`

       Once completed successfully, power off the device.

     Option 3.2:
       If you are unsure the TFTP server is correctly set up you can
       obtain the image and flash manually:

       3.2.1. `cd /tmp`
       3.2.2. `tftp-hpa 192.168.1.250 -m binary -c get mr42_u-boot.mbn`
       3.2.3. Confirm file has downloaded correctly by comparing the
              md5sum:

            `md5sum mr42_u-boot.mbn`

       3.2.4. The following are the required commands to write the image.

            `echo 1 > /sys/devices/platform/msm_nand/boot_layout
             mtd erase /dev/mtd1
             nandwrite -pam /dev/mtd1 mr42_u-boot.mbn
             echo 0 > /sys/devices/platform/msm_nand/boot_layout`

          Important: You must observe the output of the `nandwrite`
          command. Look for the following to verify writing is occurring:

            `Writing data to block 0 at offset 0x0
             Writing data to block 1 at offset 0x20000
             Writing data to block 2 at offset 0x40000`

          If you do not see this then do not power off the device. Check
          your previous commands and that mr42_u-boot.mbn was downloaded
          correctly. Once you are sure the image has been written you
          can proceed to power off the device.

  4. Hold the reset button and power on the device. This will immediately
     begin downloading the appropriate initramfs image and boot into it.

     Note: If the device does not download the initramfs, this is likely
     due to the interface not being brought up in time. Changing Ethernet
     source to a router or switch will likely resolve this. You can also
     try manually setting the link speed to 10Mb/s Half-Duplex.

  5. Once a solid white LED is displayed on the device, continue to the
     UART installation method, step 6.

Standard installation via UART - MR42 & MR52

  1. Disassemble the device and connect a UART header. The header pinout
     is as follows:

       1 - 3.3v
       2 - TXD
       3 - RXD
       4 - GND

     Important: You should only connect TXD, RXD and GND. Connecting
     3.3v may damage the device.

  2. Set your IP to 192.168.1.250. Set up a TFTP server serving
     openwrt-ipq806x-generic-meraki_(mr42|mr52)-initramfs-fit-uImage.itb.
     Separately obtain the respective sysupgrade image.

  3. Run the following commands, preferably from a Linux host. The
     mentioned files, including ubootwrite.py and u-boot images, can be
     obtained from [1].

       `python ubootwrite.py --write=(mr42|mr52)_u-boot.bin`

     The default for "--serial" option is /dev/ttyUSB0.

  4. Power on the device. The ubootwrite script will upload the image to
     the device and launch it. The second stage u-boot will in turn load
     the initramfs image by TFTP, provided the TFTP server is running
     correctly. This process will take about 13 minutes. Once a solid
     white LED is displayed, the image has successfully finished
     loading. Note: If the image does not load via TFTP, try again with
     the Ethernet link to 10Mb/s Half-Duplex.

  5. (MR42 only) Do not connect over the network. Instead connect over
     the UART using minicom or similar tool. To replace u-boot with
     the network enabled version, please run the following commands.
     Note that in the provided initramfs images, the u-boot.mbn file
     is located in /root:

     If you have not used the provided initramfs, you must ensure you
     are using an image with "boot_layout" ECC configuration enabled in
     the Kernel. This will be version 5.10 or higher. If you do not do
     this correctly the device will be bricked.

       `insmod mtd-rw i_want_a_brick=1
        mtd erase /dev/mtd8
        nandwrite -pam /dev/mtd8 /root/mr42_u-boot.mbn`

     After running nandwrite, ensure you observe the following output:

       `Writing data to block 0 at offset 0x0
        Writing data to block 1 at offset 0x20000
        Writing data to block 2 at offset 0x40000`

  6. (Optional) If you have no further use for the Meraki OS, you can
     remove all other UBI volumes on ubi0 (mtd11), including diagnostic1,
     part.old, storage and part.safe. You must not remove the ubi1 ART
     partition (mtd12).

       `for i in diagnostic1 part.old storage part.safe ; do
        ubirmvol /dev/ubi0 -N $i
        done`

  7. Proceed to flash the sysupgrade image via luci, or else download or
     scp the image to /tmp and use the sysupgrade command.

[1] The mentioned images and ubootwrite.py script can be found in this repo:
    https://github.com/clayface/openwrt-cryptid

[2] The modified u-boot sources for the MR42 and MR52 are available:
    https://github.com/clayface/U-boot-MR52-20200629

Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
2021-11-28 17:51:52 +01:00
Matthew Hagan
6e5b8c6300 ipq806x: add gsbi2_i2c label
gsbi2_i2c is used by the Meraki MR42 so we need to expose a label here.

Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
2021-11-28 17:51:52 +01:00
Matthew Hagan
771691ec83 ipq806x: backport GMAC_AHB_RESET deassert patches
Add backports of the following patches:
"net: stmmac: explicitly deassert GMAC_AHB_RESET" and
"ARM: dts: qcom: add ahb reset to ipq806x-gmac"
Required for Meraki MR42/MR52.

Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
2021-11-28 17:51:52 +01:00
Matthew Hagan
cef420e8f7 ipq806x: add GSBI nodes to ipq8064-dtsi-addidions
Rather than having separate patches for each GSBI node added, this patch
consolidates the existing GSBI1 patch into
083-ipq8064-dtsi-additions.patch. In addition, GSBI6 and GSBI7 I2C nodes,
required for the MR42 and MR52 respectively, are added.

Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
2021-11-28 17:41:18 +01:00
Robert Marko
3ad229db0b ipq40xx: add support for MikroTik hAP ac3
This adds support for the MikroTik RouterBOARD RBD53iG-5HacD2HnD
(hAP ac³), a  indoor dual band, dual-radio 802.11ac
wireless AP with external omnidirectional antennae, USB port, five
10/100/1000 Mbps Ethernet ports and PoE passthrough.

See https://mikrotik.com/product/hap_ac3 for more info.

Specifications:
 - SoC: Qualcomm Atheros IPQ4019
 - RAM: 256 MB
 - Storage: 16 MB NOR + 128 MB NAND
 - Wireless:
   · Built-in IPQ4019 (SoC) 802.11b/g/n 2x2:2, 3 dBi antennae
   · Built-in IPQ4019 (SoC) 802.11a/n/ac 2x2:2, 5.5 dBi antennae
 - Ethernet: Built-in IPQ4019 (SoC, QCA8075) , 5x 1000/100/10 port,
             passive PoE in, PoE passtrough on port 5
- 1x USB Type A port

Installation:
1. Boot the initramfs image via TFTP
2. Run "cat /proc/mtd" and look for "ubi" partition mtd device number, ex. "mtd1"
3. Use ubiformat to remove MikroTik specific UBI volumes
* Detach the UBI partition by running: "ubidetach -d 0"
* Format the partition by running: "ubiformat /dev/mtdN -y"
Replace mtdN with the correct mtd index from step 2.
3. Flash the sysupgrade image using "sysupgrade -n"

Signed-off-by: Robert Marko <robimarko@gmail.com>
Tested-by: Mark Birss <markbirss@gmail.com>
Tested-by: Michael Büchler <michael.buechler@posteo.net>
Tested-by: Alex Tomkins <tomkins@darkzone.net>
2021-11-28 17:19:52 +01:00
John Audia
81995a5e77 kernel: bump 5.4 to 5.4.162
All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/mt7621*

*I am hit with the binutils 2.37 bug so I had to revert 7f1edbd412
in order to downgrade to 2.35.1

Signed-off-by: John Audia <graysky@archlinux.us>
2021-11-28 16:32:45 +01:00
John Audia
bbdc13b15b kernel: bump 5.4 to 5.4.161
Removed upstreamed:
    ath79/patches-5.4/921-serial-core-add-support-for-boot-console-with-arbitr.patch[1]

Manually rebased:
    layerscape/patches-5.4/804-crypto-0016-MLKU-114-1-crypto-caam-reduce-page-0-regs-access-to-.patch
    octeontx/patches-5.4/0004-PCI-add-quirk-for-Gateworks-PLX-PEX860x-switch-with-.patch

All other patches automatically rebased.

1. Private email exchange with patch author, Hauke Mehrtens

Signed-off-by: John Audia <graysky@archlinux.us>
2021-11-28 16:32:45 +01:00
Christian Lamparter
a662d8550f gemini: try fis-index-block with 128 KiB sectors
Steven Maddox reported in the OpenWrt bugzilla, that his
RaidSonic IB-NAS4220-B was no longer booting with the new
OpenWrt 21.02 (uses linux 5.10's device-tree). However, it was
working with the previous OpenWrt 19.07 series (uses 4.14).

(This is still under investigation.)

Bugzilla: https://bugs.openwrt.org/index.php?do=details&task_id=4137
Reported-by: Steven Maddox <s.maddox@lantizia.me.uk>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-11-28 01:13:08 +01:00
Christian Lamparter
c3b9d0d1e2 ipq40xx: utilize nvmem on Netgear EX61X0 v2 Series
the Netgear EX6100v2 and EX6150v2 can utilize the nvmem
for the pre-calibration and mac-address for both WIFI
devices.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-11-28 01:13:08 +01:00
Christian Lamparter
297bceeecf ath79: convert TP-Link Archer C7v1/2 Wifis to nvmem-cells
For v2, both ath9k (2.4GHz Wifi) and ath10k (5 GHz) driver now
pull the (pre-)calibration data from the nvmem subsystem. v1
is slightly different as only the ath9k Wifi is supported.

This allows us to move the userspace caldata extraction
and mac-address patching for the 5GHZ ath10k supported
wifi into the device-tree definition of the device.

ath9k's nodes are also changed over to use nvmem-cells
over OpenWrt's custom mtd-cal-data property.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-11-28 01:13:08 +01:00
Christian Lamparter
dd7d4703e9 mpc85xx: backport "fix oops when CONFIG_FSL_PMC=n"
Martin Kennedy reported:
|Presently, I get this kernel panic on mpc85xx (Aerohive HiveAP 370)
|on OpenWrt 'master' which occurs right as the second processor is
|initialized:
|
|[    0.478804] rcu: Hierarchical SRCU implementation.
|[    0.535569] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
|[    0.627233] smp: Bringing up secondary CPUs ...
|[    0.681659] kernel tried to execute user page (0) - exploit attempt? (uid: 0)
|[    0.766618] BUG: Unable to handle kernel instruction fetch (NULL pointer?)
|[    0.848899] Faulting instruction address: 0x00000000
|[    0.908273] Oops: Kernel access of bad area, sig: 11 [#1]
|[    0.972851] BE PAGE_SIZE=4K SMP NR_CPUS=2 P1020 RDB
|[    1.031179] Modules linked in:
|[    1.067640] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.10.80 #0
|[    1.139507] NIP:  00000000 LR: c0021d2c CTR: 00000000
|[    1.199921] REGS: c1051cf0 TRAP: 0400   Not tainted  (5.10.80)
|[...]
|[    1.758220] NIP [00000000] 0x0
|[    1.794688] LR [c0021d2c] smp_85xx_kick_cpu+0xe8/0x568
|[    1.856126] Call Trace:
|[    1.885295] [c1051da8] [c0021cb8] smp_85xx_kick_cpu+0x74/0x568 (unreliable)
|[    1.968633] [c1051de8] [c0011460] __cpu_up+0xc0/0x228
|[    2.029038] [c1051e18] [c0031bbc] bringup_cpu+0x30/0x224
|[    2.092572] [c1051e48] [c0031f3c] cpu_up.constprop.0+0x180/0x33c
|[..]
|[    2.727952] ---[ end trace 9b796a4bafb6bc14 ]---
|[    3.800879] Kernel panic - not syncing: Fatal exception
|[    3.862353] Rebooting in 1 seconds..
|[    5.905097] System Halted, OK to turn off power
|
|I bisected this down to commit 3ae5da5adc ("kernel: bump 5.10 to 5.10.80");
|that is, I don't get the panic right before this commit, but I do after.

He reported the issue upstream and Xiaoming Ni from huawei came up with
the patch (that is on it's way to upstream). While the AP370 is not in
Openwrt, this will likely affect other SMP P1020 devices OpenWrt ships
with: like the AP330, Enterasys WS-AP3710i, etc.

Reported-by: Martin Kennedy <hurricos@gmail.com>
Tested-by: Martin Kennedy <hurricos@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-11-28 01:13:01 +01:00
Christian Lamparter
a5b80dd487 ipq40xx: purge clk_ignore_unused bootarg
these flags have been creeping in from the QSDK.
All needed clocks should be accounted for, and
if a device is broken due to this. It should be
looked into.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-11-27 23:56:29 +01:00
Christian Lamparter
db7a392ade ipq40xx: update 105-ipq40xx-fix-sleep-clock.patch
Bjorn Anderson has suggestions which would help to upstream the patch.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-11-27 23:56:29 +01:00
Mathias Kresin
6f5c27edd4 lantiq: set maximum kernel size for P2812HNUF3
The board has a fixed size kernel partition but do not limit the kernel
size during image building.

Disable image building for both boards as well, since the kernel of the
last release as well as master are to big to fit into the 2 MByte kernel
partition.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2021-11-27 21:45:06 +01:00
Aleksander Jan Bajkowski
1c68494f67 lantiq: drop kernel 5.4 support
The current state of the kernel 5.4 support is in the openwrt-21.02
branch. No need to keep a not default used kernel in this branch.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [VRX268/ bthub5]
2021-11-27 21:45:04 +01:00
Aleksander Jan Bajkowski
2f3331ea7f lantiq: switch to kernel 5.10
Use kernel 5.10 by default.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [VRX268/ bthub5]
2021-11-27 21:40:12 +01:00
Mathias Kresin
9764968bba lantiq: ar7: use okli loader for FRITZ!Box
With Kernel 5.10 the ar7 FRITZ!Box are not booting the initramfs nor the
sysupgrade image any more. Presumably due to the grown kernel.

Use the okli preloader to workaround the bootloader issue. No solution
so far for the initramfs.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2021-11-27 21:40:12 +01:00
Mathias Kresin
a328b6831c lantiq: bring back okli loader
Removed due to being unused with 1f7a03a706, but now required for the
ar7 FRITZ!Box.

Could be used for the ARV7519RW22 as well, for which the image
generation was disabled due to a stock u-boot issue with kernel bigger
than 2 MByte.

The code is combination of the ath79 and ramips okli loader.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2021-11-27 21:40:12 +01:00
John Audia
894f483d20 kernel: bump 5.10 to 5.10.82
Removed upstreamed:
    bcm53xx/patches-5.10/033-v5.16-0014-ARM-dts-NSP-Fix-mpcore-mmc-node-names.patch

Manually rebased:
    ipq806x/patches-5.10/086-ipq8064-fix-duplicate-node.patch

All other patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, ipq806x/R7800
Run-tested: bcm2711/RPi4B, ipq806x/R7800

Signed-off-by: John Audia <graysky@archlinux.us>
2021-11-27 19:19:30 +01:00
John Audia
be077f4812 kernel: bump 5.10 to 5.10.81
Manually rebased:
    octeontx/patches-5.10/0004-PCI-add-quirk-for-Gateworks-PLX-PEX860x-switch-with-.patch

All other patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, ipq806x/R7800
Run-tested: bcm2711/RPi4B, ipq806x/R7800

Signed-off-by: John Audia <graysky@archlinux.us>
2021-11-27 19:19:11 +01:00
Felix Fietkau
fb6c34d355 llvm-bpf: fix rebuild check for generating tarball
Check the version file, as it will be regenerated on rebuild

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-11-26 11:37:19 +01:00
Felix Fietkau
e73855b5d1 llvm-bpf: use SOURCE_DATE_EPOCH for generated tarball
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-11-26 11:37:13 +01:00
Sander Vanheule
f8b2bc550b realtek: Remove _machine_restart and _machine_halt
By dropping _machine_restart, users can provide more reliable or
device-specific restart modes.

_machine_halt was already removed in commit f4b687d1f0 ("realtek: use
kernel defined halt"), but quietly reintroduced in commit 8faffa00cb
("realtek: add support for the RTL9300 timer"). Let's remove it again.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
2021-11-24 21:43:56 +02:00
Sander Vanheule
927570f0a3 realtek: Add and enable watchdog node
Add and enable the Realtek Otto WDT peripheral found on these SoCs.

Default all devices to use standard (cold) reboot and "soc" resets.

Devices that require the PLL value fixup before restarting, should pick
the "cpu" or "software" reset mode. These devices also need to provide a
custom reboot mode, by adding the reboot argument to the kernel command
line:

    WDT reset mode  | kernel reboot mode
    ----------------+---------------------------------------
    soc             | reboot=cold (default if not specified)
    cpu             | reboot=warm
    software        | reboot=software

Preferrably, these devices should use an alternative restart method like
gpio-restart to provide reliable restarts.

Note that watchdog restarts are not yet exposed, since the
_machine_restart override is still present.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
2021-11-24 21:43:42 +02:00
Sander Vanheule
b8fc5eecdc realtek: Backport Realtek Otto WDT driver
Add patch submitted upstream to linux-watchdog and replace the MIPS
architecture symbols. Requires one extra patch for the DIV_ROUND_*
macros, which have moved to a different header since 5.10.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
2021-11-24 21:43:21 +02:00
Sander Vanheule
d3a62bea08 realtek: Add Lexra bus clock
The CPU peripherals on RTL83xx/RTL930x are connected to the CPU via the
Lexra bus. This bus can provide a clock signal to these peripherals, but
no clock driver is currently available. Instead, use a fixed-clock to
provide the clock frequency, and update the dependent peripherals.

Lexra bus clock frequencies:
- RTL838x: 200MHz
- RTL839x: 200MHz
- RTL930x: 175MHz

Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
2021-11-24 21:42:56 +02:00
Sander Vanheule
af2cfbda2b realtek: Consolidate bootargs
All current devices use identical bootargs, so let's move that to the
common devicetree includes.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
2021-11-24 21:42:44 +02:00
Sander Vanheule
72ae8314f5 realtek: reset both ethernet NIC and queues
Recent versions of Realtek's SDK reset both the ethernet NIC and queues
(SW_NIC_RST and SW_Q_RST bits) when initialising the hardware.

Furthermore, when issuing a CPU reset on the Zyxel GS1900-8 (not
supported by any current driver), the networking part of the SoC is not
reset. This leads to unresponsive network after the restart. By
resetting both the ethernet NIC and queues, networking always comes up
reliably.

Suggested-by: Birger Koblitz <mail@birger-koblitz.de>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
2021-11-24 21:38:43 +02:00
Rafał Miłecki
824ac6e11c bcm53xx: fix platform clocks & USB 2.0 PHY
This fixes WARNing, missing clocks and
[   10.422481] bcm_ns_usb2 1800c164.usb2-phy: Clock not defined

Fixes: 5901917b93 ("bcm53xx: use more upsteam DT patches from 5.16 / 5.17")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-11-23 13:49:10 +01:00
Rafał Miłecki
1d7c1a4198 bcm53xx: use new USB 2.0 PHY binding
This fixes:
[   10.440495] bcm_ns_usb2 1800c000.usb2-phy: can't request region for resource [mem 0x1800c000-0x1800cfff]
[   10.450039] bcm_ns_usb2 1800c000.usb2-phy: Failed to map DMU regs
[   10.456183] bcm_ns_usb2: probe of 1800c000.usb2-phy failed with error -16
caused by conflict in allocating resources.

Fixes: f55f1dbaad ("bcm53xx: switch to the kernel 5.10")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-11-23 13:49:10 +01:00
Hauke Mehrtens
cee0a95005 Revert "ath79: add support for Mikrotik LHG 5"
This reverts commit 48774decea.

This commit does not contain a valid name in the Signed-off-by line.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-11-23 00:45:39 +01:00
Rafał Miłecki
294fa3770b bcm53xx: specify switch ports on TP-LINK devices
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-11-22 15:23:22 +01:00
Felix Fietkau
340c2ed2ef tools/llvm-bpf: move tarball packing to target/llvm-bpf
This ensures that the tarball is regenerated after make clean or after switching
to a different target

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-11-22 12:00:40 +01:00
Daniel Golle
d6c5bb69cd
sunxi: build kernel with sun6i-rtc driver
sun6i-rtc cannot be built as a module and the hardware is only
present in some of the sunxi SoCs, see driver source:
        { .compatible = "allwinner,sun6i-a31-rtc" },
        { .compatible = "allwinner,sun8i-a23-rtc" },
        { .compatible = "allwinner,sun8i-h3-rtc" },
        { .compatible = "allwinner,sun8i-r40-rtc" },
        { .compatible = "allwinner,sun8i-v3-rtc" },
        { .compatible = "allwinner,sun50i-h5-rtc" },
        { .compatible = "allwinner,sun50i-h6-rtc" },

Set CONFIG_RTC_DRV_SUN6I=y in kernel config file for cortexa7 and
cortexa53 subtargets which covers all of the above.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-11-21 21:37:56 +00:00
Daniel Golle
148c516e1f
Revert "sunxi: add rtc-sun6i driver package"
sun6i-rtc is a builtin_platform_driver and cannot be built as a module.
Hence this reverts commit e178d9a549.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-11-21 21:29:49 +00:00
Eneas U de Queiroz
617fcd4879 ramips: fix ralink_i2s_debugfs_remove declaration
Correct ralink_i2s_debugfs_remove declaration in ralink patches when
CONFIG_DEBUG_FS is not selected.

Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
2021-11-20 21:08:25 +01:00
Mirko Parthey
a4c3b6373c ramips: use lzma-loader on D-Link DIR-615 H1
Fixes the boot loader LZMA decompression issue:
LZMA ERROR 1 - must RESET board to recover

Signed-off-by: Mirko Parthey <mirko.parthey@web.de>
2021-11-20 21:08:25 +01:00
Thomas Aldrian
b28443f82e ramips: add support for Wavlink WL-WN576A2
This commit adds support for the Wavlink WL-WN576A2 wall-plug wireles
repeater / router. It is also sold under the name SilverCrest SWV 733 B1.

Device specs:

- CPU: MediaTek MT7628AN
- Flash: 8MB
- RAM: 64MB
- Bootloader: U-Boot
- Ethernet: 1x 10/100 Mbps
- 2.4 GHz: b/g/n SoC
- 5 GHz: a/n/ac MT7610EN
- Buttons: WPS, reset, sliding switch (ap/repeater)
- LEDs: 5x wifi status, 1x LAN/WAN, 1x WPS

Flashing:

U-Boot launches a TFTP client if WPS button is held during boot.

- Server IP: 192.168.10.100
- Firmware file name: firmware.bin

Device will reboot automatically. First boot takes about 90s.

Coelner (waenger@gmail.com) is the original author, but I have made some
fixes. He does not wish to sign off using his real name.

Signed-off-by: Thomas Aldrian <dev.aldrian@gmail.com>
2021-11-20 21:08:25 +01:00
Sebastian Schaper
25df327086 ath79: merge D-Link DAP-2695 with dtsi
Further devices from the series have been added in the meantime,
introducing `qca955x_dlink_dap-2xxx.dtsi`.

Thus, merge support for DAP-2695 with the existing dtsi.

This implies factory images can now be flashed via the regular
OEM Web UI, as well as the bootloader recovery.

Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
2021-11-20 21:08:25 +01:00
Sebastian Schaper
be88f416db ath79: move cal-data extraction to dts for DAP-2695
This device can be merged with the existing dtsi, which declares
the location of ath9k cal-data via devicetree, correcting the 2.4G
mac address in `10_fix_wifi_mac` rather than `10-ath9k-eeprom`.

To make these changes more visible, apply before merging with dtsi.

Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
2021-11-20 21:08:25 +01:00
Sebastian Schaper
3d89685088 ath79: increase SPI frequency for D-Link DAP-2695
This device can be merged with the existing dtsi,
which will increase spi-max-frequency to 50 MHz.

To make this change more visible, increase to 50 MHz before merging.

Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
2021-11-20 21:08:25 +01:00
Andre Heider
0aa1316218 omap: switch to kernel 5.10
Signed-off-by: Andre Heider <a.heider@gmail.com>
2021-11-20 21:08:25 +01:00
Andre Heider
d58eec88b5 omap: update kernel 5.10 config
Manually set toggles are:
MMC_SDHCI_OMAP=y
TI_PRUSS_INTC=y
DRM_TI_TPD12S015=y (successor to DRM_OMAP_ENCODER_TPD12S015 [0] [1])
DRM_DISPLAY_CONNECTOR=y (for DRM_TI_TPD12S015 [1])
DRM_SIMPLE_BRIDGE=y (for DRM_TI_TPD12S015 [1])

Manually unset toggles are:
SND_MIXER_OSS=y (disabled by generic config)

The rest was automatically modified by the kernel_oldconfig make target.

[0] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=cff5e6f7e83f6271ed75972e9a2920e2c7f62d6c
[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=e7e67d9a2f1dd2f938adcc219b3769f5cc3f0df7

Signed-off-by: Andre Heider <a.heider@gmail.com>
2021-11-20 21:08:25 +01:00
Andre Heider
7f5c823da2 omap: copy kernel 5.4 config for 5.10
Signed-off-by: Andre Heider <a.heider@gmail.com>
2021-11-20 21:08:25 +01:00
Jakob (Jack/XDjackieXD)
48774decea ath79: add support for Mikrotik LHG 5
The MikroTik LHG 5 series (product codes RBLHG-5nD, RBLHG-5HPnD and
RBLHG-5HPnD-XL) devices are an outdoor 5GHz CPE with a 24.5dBi or 27dBi
integrated antenna built around the Atheros AR9344 SoC.
It is very similar to the SXT Lite5 series which this patch is based
upon.

Specifications:
 - SoC: Atheros AR9344
 - RAM: 64 MB
 - Storage: 16 MB SPI NOR
 - Wireless: Atheros AR9340 (SoC) 802.11a/n 2x2:2
 - Ethernet: Atheros AR8229 switch (SoC), 1x 10/100 port,
    8-32 Vdc PoE in
 - 8 user-controllable LEDs:
  - 1x power (blue)
  - 1x user (white)
  - 1x ethernet (green)
  - 5x rssi (green)

 See https://mikrotik.com/product/RBLHG-5nD for more details.

Notes:
 The device was already supported in the ar71xx target.

Flashing:
 TFTP boot initramfs image and then perform a sysupgrade. Follow common
 MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.

Signed-off-by: Jakob (Jack/XDjackieXD) <jakob@chaosfield.at>
2021-11-20 21:08:25 +01:00
Zhao Yu
e178d9a549 sunxi: add rtc-sun6i driver package
AP6212 wifi need wifi_pwrseq, but from OrangePi Lite 2 dts :

wifi_pwrseq: wifi_pwrseq {
	compatible = "mmc-pwrseq-simple";
	clocks = <&rtc 1>;
	clock-names = "ext_clock";
	reset-gpios = <&r_pio 1 3 GPIO_ACTIVE_LOW>; /* PM3 */
	post-power-on-delay-ms = <200>;
};

this pwrseq need rtc clock, or kernel won't find this device.
but now rtc-sunxi.c only support A10/A20.
Orangepi Lite 2 use H6 ,from rtc-sun6i.c show compatible is
	{ .compatible = "allwinner,sun6i-a31-rtc" },
	{ .compatible = "allwinner,sun8i-a23-rtc" },
	{ .compatible = "allwinner,sun8i-h3-rtc" },
	{ .compatible = "allwinner,sun8i-r40-rtc" },
	{ .compatible = "allwinner,sun8i-v3-rtc" },
	{ .compatible = "allwinner,sun50i-h5-rtc" },
	{ .compatible = "allwinner,sun50i-h6-rtc" },
So it need this to let kernel find this mmc wifi device.

As suggested by hauke, let it build as package.

Signed-off-by: Zhao Yu <574249312@qq.com>
2021-11-20 21:08:25 +01:00
Roger Pueyo Centelles
c29f71ece7 ath79: mikrotik: enable USB module on RouterBoard wAPR-2nD
The MikroTik RouterBOARD wAPR-2nD (wAP R) router features a miniPCI-e
slot with USB lines connected, which are used by some USB cards with
miniPCI-e form factor, like the R11e-LR8. Enabling USB support is
required for such cards to work.

Tested on a MikroTik wAP LR8 kit (RB wAPR-2nD + R11e-LR8).

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2021-11-20 21:08:21 +01:00
Laurent DEBOMY
e900779e6f octeon: add USB3 support (for Ubiquiti EdgeRouter 6P)
Fixes: FS#4086

Signed-off-by: Laurent DEBOMY <laurent.debomy@canal-belletrud.fr>
2021-11-20 20:54:26 +01:00
Kabuli Chana
4580516bfb mvebu: backport mvneta basic MQPrio patch
Implement a basic MQPrio support, inserting rules in RX that translate
the TC to prio mapping into vlan prio to queues.

Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
2021-11-20 20:54:26 +01:00
John Audia
c65196a48a kernel: bump 5.4 to 5.4.159
Manually rebased:
    generic-backport/850-v5.13-usb-ehci-add-spurious-flag-to-disable-overcurrent-ch.patch

All other patches automatically rebased.

Signed-off-by: John Audia <graysky@archlinux.us>
2021-11-20 18:53:14 +01:00
Jianhui Zhao
43b498f669 kernel: remove non-existent config symbols
The crashlog patch as not ported to kernel 5.4.

Fixes: 4e0c54bc5b ("kernel: add support for kernel 5.4")
Signed-off-by: Jianhui Zhao <zhaojh329@gmail.com>
2021-11-20 18:53:14 +01:00
Mark Mentovai
0c70c5c998 mediatek/mt7622: unifi-6-lr: fix ucidef network configuration typo
There's no such thing as ucidef_set_interfaces_lan. It's
ucidef_set_interface_lan.

Cc: David Bauer <mail@david-bauer.net>
Signed-off-by: Mark Mentovai <mark@moxienet.com>
2021-11-19 18:23:25 +00:00
Rafał Miłecki
0e8a5acf6e bcm4908: build chk image for Netgear RAXE500
Fixes: 63ba3eaccd ("bcm4908: start working on Netgear RAXE500 image")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-11-19 14:49:18 +01:00
Rafał Miłecki
63ba3eaccd bcm4908: start working on Netgear RAXE500 image
bootfs still needs more work before it's ready.

For some unknown reason model RAXE500 uses board id RAX220.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-11-19 14:45:47 +01:00
Rafał Miłecki
21d28adbc1 bcm4908: enable MTD_CMDLINE_PARTS
It's needed to support devices with U-Boot. That bootloader passes MTD
layout using cmdline.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-11-19 14:32:58 +01:00
Rafał Miłecki
494c033f9c bcm4908: continue work on images for U-Boot based devices
It still isn't ready though - more data needs to be added to the bootfs.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-11-19 14:32:58 +01:00
Robert Marko
ebb6f9287e sunxi: 5.10: Orange Pi Zero Plus: Fix networking
Orange Pi Zero Plus uses a Realtek RTL8211E RGMII Gigabit PHY, but its
currently set to plain RGMII mode meaning that it doesn't introduce
delays.

With this setup, TX packets are completely lost and changing the mode to
RGMII-ID so the PHY will add delays internally fixes the issue.

It looks like this got broken in 5.10 as the PHY RGMII config got fixed
due to datasheet being available and a lot of boards got broken by that.

This has already been sent upstream and received multiple reviews.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2021-11-19 09:40:29 +00:00
Rui Salvaterra
3ae5da5adc kernel: bump 5.10 to 5.10.80
Deleted (upstreamed):
ath79/patches-5.10/921-serial-core-add-support-for-boot-console-with-arbitr.patch [1]
bcm53xx/patches-5.10/033-v5.15-0012-ARM-dts-BCM5301X-Fix-memory-nodes-names.patch [2]
lantiq/patches-5.10/0016-mtd-rawnand-xway-Keep-the-driver-compatible-with-on-.patch [3]
lantiq/patches-5.10/0110-MIPS-lantiq-dma-add-small-delay-after-reset.patch [4]
lantiq/patches-5.10/0111-MIPS-lantiq-dma-reset-correct-number-of-channel.patch [5]
lantiq/patches-5.10/0112-MIPS-lantiq-dma-fix-burst-length-for-DEU.patch [6]

Manually rebased:
ipq806x/patches-5.10/0065-arm-override-compiler-flags.patch

[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.80&id=47462c5e600fbaffd755cd13dedd80d04e41ff83
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.80&id=2fde76df1885a6bec04317e457121326070450eb
[3] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.80&id=9b366f5221d8aa64b22f35be137a5749326444ce
[4] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.80&id=5af57ce8a6155fe3e4270d28d171abf8903bebc0
[5] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.80&id=b92a5df2c7adc79a57481445f67de0c1c716581f
[6] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.80&id=6b72caabc47011d03f44064452b2c65e8ed18326

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-11-19 09:40:29 +00:00
Rafał Miłecki
d745835ae1 bcm4908: backport upstream DT commits
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-11-18 17:51:24 +01:00
Rafał Miłecki
5901917b93 bcm53xx: use more upsteam DT patches from 5.16 / 5.17
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-11-18 16:34:55 +01:00
Aleksander Jan Bajkowski
0e561a2aea lantiq: improve ethernet performance
This commit contains a series of fixes for DMA. The burst length
patch significantly improves Ethernet performance. Patches were
tested on the xRX200 and xRX330.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2021-11-15 23:17:32 +01:00
Ansuel Smith
63ce6fcd20 kernel: fix mac-address-increment patch
Fix mac address increment patch. Permit to overflow to the next
byte and correctly calculate the incremented mac.

Reported-by: Chen Minqiang <ptpt52@gmail.com>
Fixes: d284e6ef0f ("treewide: convert mtd-mac-address-increment* to generic implementation")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2021-11-15 00:38:45 +01:00
Matthew Hagan
c9536520bd kernel: 5.10: backport explicit MAC06 disable patch
Backport of Ansuel Smith's "net: dsa: qca8k: make sure PAD0 MAC06
exchange is disabled", to ensure mac06 is disabled even if enabled by
the bootloader.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
2021-11-15 00:29:30 +01:00
Zoltan HERPAI
59c2a585a1 mxs: drop kernel 5.4 support
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2021-11-14 23:32:51 +01:00
Paul Spooren
d842da8d1b mxs: switch to Kernel 5.10
Signed-off-by: Paul Spooren <mail@aparcar.org>
2021-11-14 23:32:50 +01:00
Mathias Kresin
683e9cf7d0 lantiq: fix mac address from nvmem-cells
The devicetree property mac-address is expected to be set by the
bootloader and has priority over the nvmem supplied one.

Drop the mac-address address property from the dtsi files, to let the
mac address from nvmem-cells get used.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2021-11-14 20:18:17 +01:00
Christian Lamparter
e7d0dce2b3 ipq40xx: fix missing include
This patch fixes a blunder of mine. The include needed
for LED_COLOR_ID_BLUE property is missing.

This caused the builds to fail with:
|Error: arch/arm/boot/dts/qcom-ipq4019-r619ac.dtsi:91.13-14 syntax error
|FATAL ERROR: Unable to parse input tree

Fixes: 12d33d388c ("ipq40xx: add support for P&W R619AC (aka G-DOCK 2.0)")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-11-14 19:21:55 +01:00
Christian Lamparter
cb18b62206 ipq40xx: reenable Zyxel NBG6617 by default
The Zyxel NBG6617 already uses lzma to compress the kernel.
A local build with every module enabled (either as =Y or =M)
ended produced a 3058 KiB kernel (the kernel partition is 4MiB).
It booted just fine, let's reenable the device.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-11-14 14:29:47 +01:00
Richard Yu
12d33d388c ipq40xx: add support for P&W R619AC (aka G-DOCK 2.0)
P&W R619AC is a IPQ4019 Dual-Band AC1200 router.
It is made by P&W (p2w-tech.com) known as P&W R619AC
but marketed and sold more popularly as G-DOCK 2.0.

Specification:

* SOC: Qualcomm Atheros IPQ4019 (717 MHz)
* RAM: 512 MiB
* Flash: 16 MiB (NOR) + 128 MiB (NAND)
* Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN)
* Wireless:
  - 2.4 GHz b/g/n Qualcomm Atheros IPQ4019
  - 5 GHz a/n/ac Qualcomm Atheros IPQ4019
* USB: 1 x USB 3.0
* LED: 4 x LAN, 1 x WAN, 2 x WiFi, 1 x Power (All Blue LED)
* Input: 1 x reset
* 1 x MicroSD card slot
* Serial console: 115200bps, pinheader J2 on PCB
* Power: DC 12V 2A
* 1 x Unpopulated mPCIe Slot (see below how to connect it)
* 1 x Unpopulated Sim Card Slot

Installation:
1. Access to tty console via UART serial
2. Enter failsafe mode and mount rootfs
   <https://openwrt.org/docs/guide-user/troubleshooting/failsafe_and_factory_reset>
3. Edit inittab to enable shell on tty console
   `sed -i 's/#ttyM/ttyM/' /etc/inittab`
4. Reboot and upload `-nand-factory.bin` to the router (using wget)
5. Use `sysupgrade` command to install

Another installation method is to hijack the upgrade server domain
of stock firmware, because it's using insecure http.

This commit is based on @LGA1150(at GitHub)'s work
<a4932c8d5a>
With some changes:
1. Added `qpic_bam` node in dts. I don't know much about this,
   but I observed other dtses have this node.
2. Removed `ldo` node under `sd_0_pinmux`, because `ldo` cause SD card not
   working. This fix is from
   <51143b4c75>
3. Removed the 32MB NOR variant.
4. Removed `cd-gpios` in `sdhci` node, because it's reported that it makes
   wlan2g led light up.
5. Added ethphy led config in dts.
6. Changed nand partition label from `rootfs` to `ubi`.

About the 128MiB variant: The stock bootloader sets size of nand to 64MiB.
But most of this devices have 128MiB nand. If you want to use all 128MiB,
you need to modify the `MIBIB` data of bootloader. More details can be
found on github:
<https://github.com/openwrt/openwrt/pull/3691#issuecomment-818770060>
For instructions on how to flash the MIBIB partition from u-boot console:
<https://github.com/openwrt/openwrt/pull/3691#issuecomment-819138232>

About the Mini PCIe slot: (from "ygleg")
"The REFCLK signals on the Mini PCIe slot is not connected on
this board out of the box. If you want to use the Mini PCIe slot
on the board, you need to (preferably) solder two 0402 resistors:
R436 (REFCLK+) and R444 (REFCLK-)..."
This and much more information is provoided in the github comment:
<https://github.com/openwrt/openwrt/pull/3691#issuecomment-968054670>

Signed-off-by: Richard Yu <yurichard3839@gmail.com>
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
[Added comment about MIBIB+128 MiB variant. Added commit
message section about pcie slot. Renamed gpio-leds' subnodes
and added color, function+enum properties.]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-11-14 14:28:34 +01:00
Rui Salvaterra
f81dc44fd5
kernel: bump 5.10 to 5.10.79
Manually rebased:
generic/backport-5.10/810-v5.13-usb-ehci-add-spurious-flag-to-disable-overcurrent-ch.patch

Tested-by: John Audia <graysky@archlinux.us>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-11-13 18:36:47 +00:00
Daniel Golle
8fd0268b5f
mediatek: mt7622: bpi-r64: rewrite MMC uImage.FIT sysupgrade
Similar to mt7623, also no longer use 'blockdev' and stop relying on
in-kernel partition parsers. Instead, strip off all metadata using
'fwtool' while writing the firmware image and scrape the number of
blocks written from 'dd', then use that block offset to stash the
configuration backup.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-11-12 15:03:07 +00:00
Daniel Golle
c3c67fe7b1
mediatek: mt7623: re-write sysupgrade uImage.FIT on MMC
Re-reading the partition table doesn't work reliably, it fails if
anything on the device is still in use and it's not trivial to prevent
every possible case of a block device still being in use somehow.

Therefore, instead of relying on the in-kernel partition parser to know
where to write the configuration backup, use OpenWrt's format-agnostic
fwtool to strip off all metadata from the image and count its blocks
while writing. In that way we can know where to write the config backup
without needing the kernel to parse the MBR and FIT structures.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-11-12 15:03:02 +00:00
Rafał Miłecki
f1a074d0ce bcm4908: switch to kernel 5.10
Tested on:
1. Asus GT-AC5300
2. Netgear R8000P

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-11-09 12:44:26 +01:00
Rafał Miłecki
9565bd9bd6 bcm4908: add watchdog support
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-11-09 12:44:23 +01:00
Rafał Miłecki
9a18bbec1f bcm4908: refresh kernel configs
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-11-09 12:27:49 +01:00
Rafał Miłecki
c4ff53b971 bcm4908: fix b53 regression regarding RGMII reg(s)
This fixes:
[   35.308550] WARNING: CPU: 0 PID: 230 at bcm_sf2_reg_rgmii_cntrl.isra.0+0x84/0x90

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-11-08 17:52:29 +01:00
Rafał Miłecki
4e9be47087 bcm53xx: drop patch for downstream swconfig-based b53
It isn't used anymore so there is no need to hack CPU port. Upstream
(DSA-based) b53 also supports all switch ports just fine.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-11-08 15:58:42 +01:00
Rafał Miłecki
406c5002b8 bcm53xx: drop downstream patch for Buffalo WZR-1750DHP button
This patch never received a proper description and was never sent
upstream as supposed. It was meant to be handled in 2015-2018 so it
should be safe to assume noone really understands it or care.

Cc: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-11-08 15:58:30 +01:00
Rafał Miłecki
b8bbac951c layerscape: mkits-multiple-config: fail on invalid arguments
Fail if arguments couldn't be parsed and print unrecognized part. It's
important when running it from script with dynamic values. Missing value
could result in skipping argument and silent failures (unexpected its).

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-11-08 15:58:13 +01:00
Rafał Miłecki
a02c971dff bcm4908: start work on images for devices using U-Boot
New BCM4908 family based routers will use U-Boot bootloader. That will
require using a totally different firmware format. Kernel has to be put
in a FIT image.

OpenWrt has some helpers for generating .its files but they don't fit
BCM4908 requirements and there is no simple way of extending any of
them. The best solution seems to be storing an .its template.

BCM4908 bootfs may:
1. contain extra binaries (other than kernel & DTB)
2. include multiple DTB files
3. store device specific U-Boot configurations with custom properties

Such setups are too complex to generate using shell script. Raw .its
file on the other hand seems quire clean & reasonable.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-11-08 15:57:55 +01:00
Rafał Miłecki
29f12fefc0 bcm47xx: switch to kernel 5.10
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-11-08 15:56:39 +01:00
Rafał Miłecki
6cdac99401 bcm47xx: fix bgmac regression present in 5.10 kernel
This fixes:
[    2.548098] bgmac_bcma bcma0:1: Failed to register fixed PHY device
[    2.554584] bgmac_bcma bcma0:1: Cannot connect to phy
and downstream (swconfig-based) b53 driver failing to load.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-11-08 15:55:40 +01:00
Rafał Miłecki
4cd97e4760 bcm47xx: relocate LZMA loader
Kernel 5.10 grew bigger than 5.4 so we need to bump BZ_TEXT_START to
allow lzma loader hanel its size.

At the same time BZ_STACK_START needs to be increased to avoid
overwriting the stack.

For a reference see:
d5cf4a5aa4 ("brcm47xx: relocate loader to higher address")
2909a4b78e ("brcm47xx: relocate the stack in loader")

Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-11-08 15:55:26 +01:00
John Audia
83f1d72dea kernel: bump 5.10 to 5.10.78
All patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B
Run-tested: bcm2711/RPi4B

Signed-off-by: John Audia <graysky@archlinux.us>
2021-11-07 19:59:10 +01:00
John Audia
a50565157e kernel: bump 5.4 to 5.4.158
All patches automatically rebased.

Signed-off-by: John Audia <graysky@archlinux.us>
2021-11-07 19:58:08 +01:00
Paul Spooren
184d072fc0 pistachio: drop Kernel 5.4 support
With the switch to Kernel 5.10 the 5.4 files are no longer needed.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2021-11-07 18:32:21 +01:00
Paul Spooren
646c011ec7 pistachio: switch to Kernel 5.10
This was successfully boot tested on a Creator Ci40.

Signed-off-by: Paul Spooren <mail@aparcar.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-11-07 18:31:34 +01:00
Evgeniy Didin
da9a8fcbc3 archs38: update kernel version to 5.10
Update config, Makefile and image/Makefile.
Directly switch to kernel 5.10.

This patch was tested in nSIM simulator, no errors appeared.

Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Paul Spooren <mail@aparcar.org>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: John Crispin <john@phrozen.org>
2021-11-07 17:12:10 +01:00
Stijn Tintel
c5fa7ec2a6 kernel: add missing UBSAN config symbols
Enabling KERNEL_UBSAN exposes several missing symbols. Add new kernel
build options for UBSAN_BOUNDS and UBSAN_TRAP, disable CONFIG_TEST_UBSAN
in the generic kernel configs and enable CONFIG_UBSAN_MISC in generic
5.10 config. The latter symbol was removed in later kernels, as it was
causing some issues, so just disable it in 5.10 instead of adding a
build option for it.

Fixes build failures with KERNEL_UBSAN enabled.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-11-07 17:38:01 +02:00
Stijn Tintel
ec68c75c62 kernel: add missing KASAN config symbols
Enabling KERNEL_KASAN exposes several missing symbols. As KASAN_SW_TAGS
is only implemented for arm64 CPUs and requires clang, it doesn't make
sense to make this a build option so just default to KASAN_GENERIC and
disable KASAN_SW_TAGS.

While at it, disable TEST_KASAN_MODULE in the generic 5.10 config.

Fixes build failures with KERNEL_KASAN enabled.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-11-07 17:26:47 +02:00
Matthew Hagan
f2f42a54e8 kernel: 5.10: compress 7xx patch numbering
The qca8k patch series brings the numbering to 799. This patch renames
7xx patches to create space for more backports to be added.

Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
[rename 729->719]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-11-07 00:05:26 +01:00
Pawel Dembicki
07543d00e5 ipq40xx: use zImage for Cell-C RTL30VW
After switch to 5.10 kernel, kernel size was too high.
This patch switches Cell-C RTL30VW from uImage to zImage build.

Lzma uImage wrap is required for factory booting and it must left
untouched.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2021-11-06 23:36:32 +01:00
Wout Bertrums
9a7e3d170c ramips: add broken-flash-reset for HLK-7621A EvB
This is needed because the HLK-7621 EvB has 32MB of flash,
so it will have to use 4B addressing and the
broken-flash-reset hack has to be used to be able to reboot.

Signed-off-by: Wout Bertrums <wout@wbnet.eu>
[copied github message into commit message]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-11-06 23:36:32 +01:00
Robert Marko
605d280914 ipq40xx: 5.10: refresh config
It looks like CONFIG_BLK_CMDLINE_PARSER was forgotten during the Orbi
device merge.
So lets refresh the config with it.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2021-11-06 23:36:32 +01:00
Alberto Bursi
ab1969d9a8 x86: sort alphabetically default packages
sorting alphabetically default packages
and placing them on their own line.

Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
[fixed whitespaces before tab, double whitespaces]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-11-06 23:36:32 +01:00
Alberto Bursi
1f188d8c72 x86: enable kmod-tg3 on 64-bit by default
Gigabit ethernet adapters using BCM5719/5720 chipset
are common on servers and as easy/cheap to get as
Intel based ones.
Usually found in 2-port and 4-port cards.

Also some devices recently added to x86_64 target
like the Meraki MX100 use this chipset for 8 of
their 12 integrated ports.

Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
2021-11-06 23:36:32 +01:00
Sergio Paracuellos
8bc6654244 ramips: mt7621-dts: properly organize pcie node
Device tree pcie node for this SoC is using different
styles in its different properties. Hence properly
unify them to be able to write a a proper yaml schema
documentation.

Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20210505121736.6459-11-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-11-06 23:36:32 +01:00
Sergio Paracuellos
2bc659ee07 ramips: mt7621-dts: add missing device_type in pcie root ports
According to the YAML schema 'pci-bus.yaml' the 'device_type'
property is mandatory for all pcie root ports. Hence add it.

Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20210506170742.28196-3-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-11-06 23:36:32 +01:00
Sergio Paracuellos
82f9d5ad0b ramips: mt7621-dts: remove 'bug-range' property
Property 'bus-range' when values are the default are
not necessary to be defined. Hence, remove all of them.

Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20210506170742.28196-2-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-11-06 23:36:32 +01:00
Sergio Paracuellos
e04130fc17 ramips: mt7621-dts: use standard 'syscon' string
Both 'memc' and 'sysc' nodes are not using 'syscon'
as a node string which is the standard one to be used.
Update both of them.

Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20210505132154.8263-3-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-11-06 23:36:32 +01:00
Sergio Paracuellos
f1d154ec6c ramips: mt7621-dts: remove ethsys node
DT 'ethsys' node is being configured as a syscon
to get access to reset and other registers in the
'mediateķ,mt7621-eth' driver. Since the 'sysc' is also
a syscon, provides the clock and also is virtually
mapped from the same physical address 0x1e000000 we
can just use 'sysc' as the phandle for the syscon in
the ethernet node. Compatible string 'mediatek,mt7621-ethsys'
of the node is not being used anywhere inside the kernel
so, this node can be safely removed.

Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20210505132154.8263-2-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-11-06 23:36:32 +01:00
DENG Qingfang
93da227798 ramips: mt7621-dts: remove obsolete switch node
This was for OpenWrt's swconfig driver, which never made it upstream,
and was also superseded by MT7530 DSA driver.

Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Link: https://lore.kernel.org/r/20210108025155.31556-1-dqfext@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-11-06 23:36:32 +01:00
Sergio Paracuellos
6e30692e99 ramips: mt7621-dts: properly define 'cpc' and 'mc' nodes
'cpc' and 'mc' nodes correspond with the MIPS 'Cluster Power Controller'
and 'MIPS Common Device Memory Map' which are present in some MIPS related
boards. There is already bindings documentation for these two located in:
- Documentation/devicetree/bindings/power/mti,mips-cpc.yaml
- Documentation/devicetree/bindings/bus/mti,mips-cdmm.yaml

Hence, properly update compatible strings and align nodes with already
mainlined bindings documentation. Also, move their definition to a proper
place since both of them are not related with the palmbus at all.

Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20211002060706.30511-1-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-11-06 23:36:32 +01:00
Sergio Paracuellos
9b52b4e53f ramips: mt7621-dts: change some node hex addresses to lower case
Hexadecimal addresses in device tree must be defined using lower case.
There are some of them that are still in upper case. Change them all.

Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20211017070656.12654-2-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-11-06 23:36:32 +01:00
Sergio Paracuellos
e17f238f1d ramips: mt7621-dts: make use of 'IRQ_TYPE_LEVEL_HIGH' instead of magic numbers
Nodes 'gdma' and 'hsdma' are using magic number '4' in interrupts property.
Use 'IRQ_TYPE_LEVEL_HIGH' instead to align with the rest of the nodes in
the file.

Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20211019102915.15409-2-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-11-06 23:36:32 +01:00
Christian Lamparter
217571b6ab ath79: WNDR3700/3800/MAC: utilize nvmem for caldata fetching
converts the still popular WNDR3700 Series to fetch the
caldata through nvmem. As the "MAC with NVMEM" has shown,
there could pitfalls along the way.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-11-06 22:18:45 +01:00
John Audia
30b0bd69fd kernel: bump 5.4 to 5.4.156
Removed upstreamed:
  backport-5.4/790-v5.7-net-switchdev-do-not-propagate-bridge-updates-across.patch

All other patches automatically rebased.

Signed-off-by: John Audia <graysky@archlinux.us>
2021-11-06 14:48:20 +01:00
Rui Salvaterra
4b26ba4155 kernel: bump 5.10 to 5.10.77
Deleted (upstreamed):
bcm53xx/patches-5.10/081-v5.15-Revert-pinctrl-bcm-ns-support-updated-DT-binding-as-.patch [1]

[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-5.10.y&id=01c2881bb0e0a71b87ca425e1b763ac13855aa7e

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-11-06 14:24:07 +01:00
Paul Spooren
15e55a2190 imagebuilder: fix local packages/ folder
This commit fixes commit "2999f810ff: build,IB: include kmods only in
local builds" which cause the local packages/ folder only to be added
for local builds but no longer for ImageBuilder created by the Buildbot.

The commits intention was to use remote kmods repositories rather than
storing them locally. Accidentally the entire handling of the local
`packages/` was removed.

Re-add the folder and include a README describing what it can be used
for.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2021-11-05 19:18:48 -10:00
Felix Fietkau
2a832b3df5 llvm-bpf: support creating a tarball in bin
This can be used for adding the toolchain to an existing tree without having
to build it from scratch.
Enable building the toolchain + tarball by default on buildbot

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-11-04 16:59:22 +01:00
Sungbo Eo
f432353850 bcm4908: fix calculation of new cferam index
The arithmetic expansion fails when idx becomes a two digit number.
Fix this by relying on expr command.

root@OpenWrt:/# echo $(((028 + 0) % 1000))
/bin/ash: arithmetic syntax error
root@OpenWrt:/# echo $(($(expr 028 + 0) % 1000))
28

Fixes: a6a0b252ba ("bcm4908: add sysupgrade support")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2021-11-04 15:52:03 +01:00
Rafał Miłecki
1ee6d3d24e bcm53xx: add first 5.17 DTS changes
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-11-04 07:00:21 +01:00
Robert Marko
ae7c2bb61b ipq40xx: disable some devices due to kernel size
Disable some of the ipq40xx devices due to their kernel size limitations.

These devices fail to build with kernel 5.10 and full buildbot config.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
[keep gl-b1300/gl-s1300 enabled, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-11-03 23:50:56 +01:00
Adrian Schmutzler
16af6535fa ipq40xx: switch to kernel 5.10
There have been enough tests and new developments require the new
kernel, so let's update it.

There is a bunch of devices that do not build anymore due to
kernel size limitations. These are disabled in a subsequent commit.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-11-03 23:50:56 +01:00
Piotr Dymacz
e245ae13ee imx: remove obsolete Kernel 5.4
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2021-11-03 12:45:40 +01:00
Piotr Dymacz
3c8720f39e imx: update subtargets default kernel configs for 5.10
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2021-11-03 12:45:40 +01:00
Piotr Dymacz
adc37b8040 imx: make kernel 5.10 default version
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2021-11-03 12:45:40 +01:00
Piotr Dymacz
b35cd4d71d imx: introduce 'cortexa7' subtarget
This adds some essential files required by new 'cortexa7' subtarget,
dedicated for Cortex-A7 based NXP i.MX series. For now, the kernel
config-default focuses only on the i.MX 6UL family, as the following
changeset will introduce support for i.MX 6ULL based device. Support
for more platforms (e.g. i.MX 7) might be enabled later, while adding
more devices.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2021-11-03 12:45:40 +01:00
Piotr Dymacz
d2fb495a9d imx: split into arch-specific subtargets
Modern NXP i.MX series includes several different families, based on
single- or multi-core Arm Cortex-A CPUs. To be able to support more
families within a single target, we split the 'imx' in arch-specific
subtargets, starting with 'cortexa9' for the Cortex-A9 based i.MX 6,
already supported by the original 'imx6' target.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2021-11-03 12:45:40 +01:00
Piotr Dymacz
d1c66eacab imx6: rename target to 'imx'
This is first step in migrating to a generic i.MX target which in the
next steps will also get divided into arch-specific subtargets.

In the result, this will make it possible to support, within a single
target, also other modern NXP i.MX families, like the i.MX 7, i.MX 8
or recently introduced i.MX 9.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2021-11-03 12:45:40 +01:00
Piotr Dymacz
7abde5037d imx6: refresh and update target kernel configs
This is a minor extension of the commit 26ae69fd03 ("imx6: refresh
kernel config with 5.10 symbols"), with correct and full disable of
the Arm Cortex-A7 based i.MX 6UL and 6UL{L,Z} families support and
re-enable of the Cortex-A9 based i.MX 6L{S,X}.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2021-11-03 12:45:40 +01:00
Piotr Dymacz
5ec4b180c2 imx6: image: fix Gateworks Ventana boot script filename
U-Boot for the Gateworks Ventana includes filename of the boot script in
the default/embedded environment (see 'include/configs/gw_ventana.h' in
the U-Boot sources).

This restores the old boot script filename ('6x_bootscript-ventana'),
making Ventana boards boot again.

Fixes: 8dba71dd33 ("imx6: image: drop BOOT_SCRIPT and fix DEVICE_NAME")
Reported-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2021-11-03 12:45:40 +01:00
Piotr Dymacz
5dfa89be99 ath79: add support for Netgear R6100
Netgear R6100 is a dual-band Wi-Fi 5 (AC1200) router based on Qualcomm
Atheros (AR9344 + QCA9882) platform. Support for this device was first
introduced in 15f6f67d18 (ar71xx). FCC ID: PY312400225.

Specifications:

- Atheros AR9344 (560 MHz)
- 128 MB of RAM (DDR2)
- 128 MB of flash (parallel NAND)
- 2T2R 2.4 GHz Wi-Fi (AR9344)
- 2T2R 5 GHz Wi-Fi (QCA9882)
- 5x 10/100 Mbps Ethernet (AR9344)
- 4x internal antenna
- 1x USB 2.0 (GPIO-controlled power)
- 6x LED, 3x button (reset, Wi-Fi, WPS)
- UART (4-pin, 2.54 mm pitch) header on PCB
- 1x mechanical power switch
- DC jack for main power input (12 V)

WARNING: sysupgrade from older stable releases is not possible, fresh
installation (via vendor's GUI or TFTP based recovery) is required.
Reason for that is increased kernel partition size.

Installation:

Use the 'factory' image under vendor's GUI or via TFTP U-Boot recovery.
You can use the 'nmrpflash' tool at a boot time, before kernel is loaded
or start it manually by pressing the 'reset' button for ~20 seconds from
powering up the device (U-Boot will start TFTP server on 192.168.1.1,
use TFTP client to send the image).

Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2021-11-03 12:45:40 +01:00
Rafał Miłecki
20d3e236b2 bcm4908: add testing support for kernel 5.10
CONFIG_COMPAT_32BIT_TIME is a new symbol and has to be set to avoid:
Provide system calls for 32-bit time_t (COMPAT_32BIT_TIME) [N/y/?] (NEW)

CONFIG_RELOCATABLE needs to be enabled to make kernel start booting.
That raises a question: do we really need CONFIG_EXPERT=y ?

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-11-03 12:16:06 +01:00
Rafał Miłecki
e3a1e78cd8 bcm4908: prepare kernel 5.10 support
It compiles but *doesn't* boot so it isn't enabled yet.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-11-03 12:08:40 +01:00
Hauke Mehrtens
b7bb176d1c pistachio: Take bootargs from device tree
The boot arguments are copied into the device tree by the boot loader
and taken from the device tree by the kernel.
The code which takes the boot arguments from the different sources was
reworked with kernel 5.5.

We have to activate CONFIG_MIPS_CMDLINE_DTB_EXTEND to take the boot
arguments from the device tree.

This makes the system boot on the board again.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-11-02 23:37:19 +01:00
Hauke Mehrtens
ff504e6fd1 pistachio: Make kernel 5.10 patches apply
Make the patches apply on kernel 5.10 and refresh the patches and the
kernel configuration on top of kernel 5.10.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-11-02 23:37:19 +01:00
Hauke Mehrtens
9b96fcf9f6 pistachio: Copy kernel 5.4 patches to 5.10
This just copies the patches and the configuration from kernel 5.4 to
kernel 5.10.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-11-02 23:37:19 +01:00
Hauke Mehrtens
6e5ab1b154 pistachio: Fix FIT image configuration name
The pistachio U-Boot expects a default configuration with the name
config@1 in the FIT image. The default was changed in OpenWrt some
months ago.
This makes the board boot again.

Fixes: 9f714398e0 ("build: use config-1 instead of config@1 as default")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-11-02 23:37:19 +01:00
Hauke Mehrtens
df68042d5b kernel: Set some options in generic configuration
Add CONFIG_USB_ETH and CONFIG_PWM_JZ4740 to generic kernel
configuration.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-11-02 23:37:19 +01:00
Mathias Kresin
f7f12495bc kernel: 5.10: simplify logic in packet mangling patch
I had quite a hard time to understand what the change to net/core/dev.c
is supposed to do.

Simplify the change by returning NETDEV_TX_OK in case a eth_mangle_tx
callback was set but returned NULL instead of setting the return value
in the else branch.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2021-11-02 22:36:41 +01:00
Mathias Kresin
1470009bf8 kernel: 5.10: packet mangling code only for ar8216 driver
Only the ar8216 switch driver uses the packet mangling code.

Update the kernel configs accordingly.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2021-11-02 22:36:41 +01:00
Mathias Kresin
9201ff5476 kernel: 5.10: fix ar8216 vlans
ar8216 switches have a hardware bug, which renders normal 802.1q support
unusable. Packet mangling is required to fix up the vlan for incoming
packets.

The patch was ommited at the time kernel 5.10 support was added but is
still required for ar8216 switches.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2021-11-02 22:36:41 +01:00
Paul Spooren
7b7bbec453 uml: add Kernel 5.10 support via testing
Add the latest default Kernel for testing. This step is required to keep
UML in tree for the next release.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2021-11-02 10:04:50 -10:00
Paul Spooren
106c8add9c uml: build target again via the Buildbots
The UML target been outdated for a long time. Instead of just carrying
unmaintained code we should build it again and allow people and CIs to
use it for testing.

This commit removes the `source-only` feature which disables building.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2021-11-02 10:04:50 -10:00
Paul Spooren
02c23d004c uml: drop 32Bit host build support
This step drops support host build systems other than x86/64 to allow
two Kernel configuration in parallel. With this commit the setup follow
the config style of all other targets.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2021-11-02 10:04:50 -10:00
Paul Spooren
841738aa55 uml: update README to usable examples
The current `uml` README is terribly outdated and non of the examples
work by default. Fix that and while at it convert it to Markdown.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2021-11-02 10:04:50 -10:00
Daniel Golle
b82a23e959
kernel: remove custom partition name patch
Don't patch the kernel to expose the partition name in sysfs as it is
already exposed via 'uevent'.
All previous users have been converted to use 'uevent', so we can
safely drop the custom patch.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-11-01 18:20:18 +00:00
Daniel Golle
b070359035
mediatek: mt7623: make use of find_mmc_part
Use find_mmc_part instead of previously introduced
get_partition_by_name which requires a custom kernel patch.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-11-01 18:00:57 +00:00
Daniel Golle
5a0348fdc3
mediatek: mt7622: make use of find_mmc_part
Use find_mmc_part instead of previously introduced
get_partition_by_name which requires a custom kernel patch.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-11-01 18:00:52 +00:00
Davide Fioravanti
2cb24b3f3c ipq40xx: add support for Netgear SRR60/SRS60 and RBR50/RBS50
The Netgear SRS60 and SRR60 (sold together as SRK60) are two almost
identical AC3000 routers. The SRR60 has one port labeled as wan while
the SRS60 not. The RBR50 and RBS50 (sold together as RBK50) have a
different external shape but they have an USB 2.0 port on the back.

This patch has been tested only on SRS60 and RBR50, but should work
on SRR60 and RBS50.

Hardware
--------
SoC:   Qualcomm IPQ4019 (717 MHz, 4 cores 4 threads)
RAM:   512MB DDR3
FLASH: 4GB EMMC
ETH:
  - 3x 10/100/1000 Mbps Ethernet
  - 1x 10/100/1000 Mbps Ethernet (WAN)
WIFI:
  - 2.4GHz: 1x IPQ4019 (2x2:2)
  - 5GHz:   1x IPQ4019 (2x2:2)
  - 5GHz:   1x QCA9984 (4x4:4)
  - 6 internal antennas
BTN:
  - 1x Reset button
  - 1x Sync button
  - 1x ON/OFF button
LEDS:
  - 8 leds controlled by TLC59208F (they can be switched on/off
    independendently but the color can by changed by GPIOs)
  - 1x Red led (Power)
  - 1x Green led (Power)
UART:
  - 115200-8-N-1

Everything works correctly.

Installation
------------
These routers have a dual partition system. However this firmware works
only on boot partition 1 and the OEM web interface will always flash on
the partition currently not booted.

The following steps will use the SRS60 firmware, but you have to chose
the right firmware for your router.

There are 2 ways to install Openwrt the first time:

1) Using NMRPflash
 1. Download nmrpflash (https://github.com/jclehner/nmrpflash)
 2. Put the openwrt-ipq40xx-generic-netgear_srs60-squashfs-factory.img
	file in the same folder of the nmrpflash executable
 3. Connect your pc to the router using the port near the power button.
 4. Run "nmrpflash -i XXX -f openwrt-ipq40xx-generic-netgear_srs60-squashfs-factory.img".
	Replace XXX with your network interface (can be identified by
	running "nmrpflash -L")
 5. Power on the router and wait for the flash to complete. After about
	a minute the router should boot directly to Openwrt. If nothing
	happens try to reboot the router. If you have problems flashing
	try to set "10.164.183.253" as your computer IP address

2) Without NMRPflash
The OEM web interface will always flash on the partition currently not
booted, so to flash OpenWrt for the first time you have to switch to
boot partition 2 and then flash the factory image directly from the OEM
web interface.

To switch on partition 2 you have to enable telnet first:
 1. Go to http://192.168.1.250/debug.htm and check "Enable Telnet".
 2. Connect through telent ("telnet 192.168.1.250") and login using
	admin/password.

	To read the current boot_part:
		artmtd -r boot_part

	To write the new boot_part:
		artmtd -w boot_part 02

	Then reboot the router and then check again the current booted
	partition

Now that you are on boot partition 2 you can flash the factory Openwrt
image directly from the OEM web interface.

Restore OEM Firmware
--------------------
 1. Download the stock firmware from official netgear support.
 2. Follow the nmrpflash procedure like above, using the official
	Netgear firmware (for example SRS60-V2.2.1.210.img)

        nmrpflash -i XXX -f SRS60-V2.2.1.210.img

Notes
-----
1) You can check and edit the boot partition in the Uboot shell using
	the UART connection.
	"boot_partition_show" shows the current boot partition
	"boot_partition_set 1" sets the current boot partition to 1

2) Router mac addresses:

   LAN XX:XX:XX:XX:XX:69
   WAN XX:XX:XX:XX:XX:6a
   WIFI 2G XX:XX:XX:XX:XX:69
   WIFI 5G XX:XX:XX:XX:XX:6b
   WIFI 5G (2nd) XX:XX:XX:XX:XX:6c

   LABEL XX:XX:XX:XX:XX:69

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
[added 5.10 changes for 901-arm-boot-add-dts-files.patch, moved
sysupgrade mmc.sh to here and renamed it, various dtsi changes]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-11-01 00:56:51 +01:00
Davide Fioravanti
24efb49ff0 ipq40xx: enable CONFIG_CMDLINE_PARTITION and CONFIG_LEDS_TLC591XX
CONFIG_CMDLINE_PARTITION:
Some devices with mmc like the Netgear Orbi Pro SRS60 or Netgear Orbi
RBR50 needs to hardcode the partitions layout in the cmdline boot
correctly

CONFIG_LEDS_TLC591XX:
This is needed for the led driver found in the Netgear Orbi Pro SRS60

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Shang Jia <jiash416@gmail.com>
[added 5.10 config]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-11-01 00:56:51 +01:00
Sander Vanheule
c735d2e218 realtek: backport GPIO IRQ index fix
Backport the patch queued upstream for 5.16. The patch differs slightly
from the upstream patch due to an upstream change that added a
convenience function.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2021-11-01 00:56:51 +01:00
Pavel Kubelun
78be2741aa ipq40xx: fix sleep clock
It seems like sleep_clk was copied from ipq806x.
Fix ipq40xx sleep_clk to the value QSDK defines.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [5.4+5.10]
2021-11-01 00:56:51 +01:00
Christian Lamparter
abb4083fa0 apm821xx: MBL: MR24: fetch IP address over dhcp by default
This patch changes the default network configuration
to fetch the IP addresses over dhcp instead of being
statically assigned.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-11-01 00:56:51 +01:00
Nicolò Veronese
3f96743459 ath79: fix UBNT Aircube AC gpios
GPIOs on the Aircube AC are wrong:
 - Reset GPIO moved from 17 to 12
 - PoE Pass Through GPIO for Aircube AC is 3

Fixes: 491ae3357e ("ath79: add support for Ubiquiti airCube AC")

Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
2021-11-01 00:43:18 +01:00
Shiji Yang
184dc6e32a ath79: add support for Letv LBA-047-CH
Specifications:
SOC: QCA9531 650 MHz
ROM: 16 MiB Flash (Winbond W25Q128FV)
RAM: 128 MiB DDR2 (Winbond W971GG6SB)
LAN: 10/100M *2
WAN: 10/100M *1
LED: BGR color *1

Mac address:
label	C8:0E:77:xx:xx:68	art@0x0
lan	C8:0E:77:xx:xx:62	art@0x6
wan	C8:0E:77:xx:xx:68	art@0x0    (same as the label)
wlan	C8:0E:77:xx:xx:B2	art@0x1002 (load automatically)

TFTP installation:
* Set local IP to 192.168.67.100 and open tftpd64, link lan
  port to computer.
  Rename "xxxx-factory.bin" to
  "openwrt-ar71xx-generic-ap147-16M-rootfs-squashfs.bin".
* Make sure firmware file is in the tftpd's directory, push
  reset button and plug in, hold it for 5 seconds, and then
  it will download firmware from tftp server automatically.

More information:
* This device boot from flash@0xe80000 so we need a okli
  loader to deal with small kernel partition issue. In order
  to make full use of the storage space, connect a part of the
  previous kernel partition to the firmware.

  Stock                          Modify
  0x000000-0x040000(u-boot)      0x000000-0x040000(u-boot)
  0x040000-0x050000(u-boot-env)  0x000000-0x050000(u-boot-env)
  0x050000-0xe80000(rootfs)      0x050000-0xe80000(firmware part1)
  0xe80000-0xff0000(kernel)      0xe80000-0xe90000(okli-loader)
                                 0xe90000-0xff0000(firmware part2)
  0xff0000-0x1000000(art)        0xff0000-0x1000000(art)

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2021-11-01 00:15:09 +01:00
Jihoon Han
84451173f0 ath79: add support for Dongwon T&I DW02-412H
Dongwon T&I DW02-412H is a 2.4/5GHz band 11ac (WiFi-5) router, based on
Qualcomm Atheros QCA9557.

Specifications
--------------

- SoC: Qualcomm Atheros QCA9557-AT4A
- RAM: DDR2 128MB
- Flash: SPI NOR 2MB (Winbond W25Q16DVSSIG / ESMT F25L16PA(2S)) +
         NAND 64/128MB
- WiFi:
  - 2.4GHz: QCA9557 WMAC
  - 5GHz: QCA9882-BR4A
- Ethernet: 5x 10/100/1000Mbps
  - Switch: QCA8337N-AL3C
- USB: 1x USB 2.0
- UART:
  - JP2: 3.3V, TX, RX, GND (3.3V is the square pad) / 115200 8N1

Installation
--------------

1.  Connect a serial interface to UART header and
    interrupt the autostart of kernel.
2.  Transfer the factory image via TFTP and write it to the NAND flash.
3.  Update U-Boot environment variable.
    > tftpboot 0x81000000 <your image>-factory.img
    > nand erase 0x1000000
    > nand write 0x81000000 0x1000000 ${filesize}
    > setenv bootpart 2
    > saveenv

Revert to stock firmware
--------------

1.  Revert to stock U-Boot environment variable.
    > setenv bootpart 1
    > saveenv

MAC addresses as verified by OEM firmware
--------------

   WAN: *:XX (label)
   LAN: *:XX + 1
  2.4G: *:XX + 3
    5G: *:XX + 4

The label MAC address was found in art 0x0.

Credits
--------------

Credit goes to the @manatails who first developed how to port OpenWRT
to this device and had a significant impact on this patch.

And thanks to @adschm and @mans0n for guiding me to revise the code
in many ways.

Signed-off-by: Jihoon Han <rapid_renard@renard.ga>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
Tested-by: Sungbo Eo <mans0n@gorani.run>
2021-10-31 21:58:28 +01:00
Jihoon Han
a61a41d4aa kernel: add support for ESMT F25L16PA(2S) SPI-NOR
This fixes support for Dongwon T&I DW02-412H which uses F25L16PA(2S) flash.

Signed-off-by: Jihoon Han <rapid_renard@renard.ga>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
[refresh patches]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-10-31 21:56:56 +01:00
Robert Marko
76fff69180 ipq806x: ecw5410: use bootloader provided MAC-s
Currently, we are overriding the bootloader provided MAC-s as the ethernet
aliases are reversed so MAC-s were fixed up in userspace.
There is no need to do that as we can just fix the aliases instead and get
rid of MAC setting via userspace helper.

Fixes: 59f0a0f ("ipq806x: add Edgecore ECW5410 support")

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2021-10-31 21:24:47 +01:00
Robert Marko
2e3c79ef83 ipq806x: ecw5410: fix PCI1 radio caldata
ECW5410 has 2 QCA9984 cards, one per PCI controller.
They are located at PCI adresses 0001:01:00.0 and 0002:01:00.0.

Currently, pre-cal is not provided for 0001:01:00.0 at all,but for
0000:01:00.0 which is incorrect and causes the ath10k driver to not
be able to fetch the BMI ID and use that to fetch the proper BDF but
rather fail with:
[   12.029708] ath10k 5.10 driver, optimized for CT firmware, probing pci device: 0x46.
[   12.031816] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142)
[   12.037660] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[   13.173898] ath10k_pci 0001:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe
[   13.174015] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[   13.189304] ath10k_pci 0001:01:00.0: firmware ver 10.4b-ct-9984-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc35
[   15.492322] ath10k_pci 0001:01:00.0: failed to fetch board data for bus=pci,vendor=168c,device=0046,subsystem-vendor=168c,subsystem-device=cafe,variant=Edgecore-ECW541 from ath10k/QCA9984/hw1.0/board-2.bin
[   15.543883] ath10k_pci 0001:01:00.0: failed to fetch board-2.bin or board.bin from ath10k/QCA9984/hw1.0
[   15.543920] ath10k_pci 0001:01:00.0: failed to fetch board file: -12
[   15.552281] ath10k_pci 0001:01:00.0: could not probe fw (-12)

So, provide the pre-cal for the actual PCI card and not the non-existent
one.

Fixes: 59f0a0f ("ipq806x: add Edgecore ECW5410 support")

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2021-10-31 21:24:47 +01:00
Robert Marko
fa3646c003 ipq806x: ecw5410: drop GPIO based MDIO1 node
It looks like this is a leftover before there was a proper MDIO driver.
Since both PHY-s are connected to the HW MDIO bus there is no reason for
this to exist anymore, especially since it uses the same pins as the HW
controller and has the pinmux for the set to "MDIO" so this worked by
pure luck as GPIO MDIO would probe first and override the HW driver.

Move the GMAC3 to simply use the same MDIO bus phandle.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2021-10-31 21:24:47 +01:00
André Valentin
766d1d675b ath79: fix parallel image generation for Zyxel NBG6716
This changes the image generation to use a unique directory. With
parallel building it may occur that two concurrent jobs try
to create an image which leds to errors. It also removes a needless
subdirecory.

Signed-off-by: André Valentin <avalentin@marcant.net>
2021-10-31 21:24:47 +01:00
Sergio Paracuellos
eb00fb8f71 ramips: add support for HiLink HLK-7621A evaluation board
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 256 MB (DDR3)
- Flash: 32 MB SPI NOR 44MHz
- Switch: 1 WAN, 4 LAN (Gigabit)
- LEDs: 1 WAN, 4 LAN (controlled by PHY)
- USB Ports: 1 x USB2, 1 x USB3
- WLAN: 1 x 2.4, 5 GHz 866Mbps (MT7612E)
- Button: 1 button (reset)
- UART Serial: UART1 as console : 57600 baud
- Power: 12VDC, 1A

Installation:
Update openWRT firmware using internal GNUBEE uboot:
https://github.com/gnubee-git/GnuBee-MT7621-uboot

By HTTP: Initial uboot address is http://10.10.10.123, your address
needs to be 10.10.10.x, and mask 255.255.255.0.
By TFTP: Uboot is in client mode, the address of the firmware must
be tftp://10.10.10.3/uboot.bin

Recovery:
Manufacturer provides MTK OpenWrt 14.07 source code, compile then
flash it by uboot.
HLK-7621A is a stamp hole package module for embedded development,
users have to design IO boards to use it.

MAC addresses:
- u-boot-env contains a placeholder address:
  > mtd_get_mac_ascii u-boot-env ethaddr
  03:17:73🆎cd:ef
- phy0 gets a valid-looking address:
  > cat /sys/class/ieee80211/phy0/macaddress
  f8:62:aa:**:**:a8
- Calibration data for &pcie2 contains a valid address, however the
  zeros in the right half look like it's not real:
  8c:88:2b:00:00:1b
- Since it's an evaluation board and there is no solid information
  about the MAC address assignment, the ethernet MAC address is left random.

Signed-off-by: Chen Yijun <cyjason@bupt.edu.cn>
[add keys and pcie nodes to properly support evaluation board]
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
[remove ethernet address, wrap lines properly]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-10-31 21:24:47 +01:00
Eduardo Santos
3c97fb4346 ramips: add support for Xiaomi MiWifi 3C
This commit adds support for Xiaomi MiWiFi 3C device.

Xiaomi MiWifi 3C has almost the same system architecture
as the Xiaomi Mi WiFi Nano, which is already officially
supported by OpenWrt.

The differences are:

 - Numbers of antennas (4 instead of 2). The antenna management
   is done via the µC. There is no configuration needed in the
   software code.
 - LAN port assignments are different. LAN1 and WAN are
   interchanged.

OpenWrt Wiki: https://openwrt.org/toh/xiaomi/mir3c

OpenWrt developers forum page:
https://forum.openwrt.org/t/support-for-xiaomi-mi-3c

Specifications:

 - CPU: MediaTek MT7628AN (575MHz)
 - Flash: 16MB
 - RAM: 64MB DDR2
 - 2.4 GHz: IEEE 802.11b/g/n with Integrated LNA and PA
 - Antennas: 4x external single band antennas
 - WAN: 1x 10/100M
 - LAN: 2x 10/100M
 - LED: 1x amber/blue/red. Programmable
 - Button: Reset

MAC addresses as verified by OEM firmware:

use address source
LAN *:92 factory 0x28
WAN *:92 factory 0x28
2g *:93 factory 0x4

OEM firmware uses VLAN's to create the network interface for WAN and LAN.

Bootloader info:
The stock bootloader uses a "Dual ROM Partition System".
OS1 is a deep copy of OS2.
The bootloader start OS2 by default.
To force start OS1 it is needed to set "flag_try_sys2_failed=1".

How to install:
1- Use OpenWRTInvasion to gain telnet, ssh and ftp access.
   https://github.com/acecilia/OpenWRTInvasion
   (IP: 192.168.31.1 - Username: root - Password: root)
2- Connect to router using telnet or ssh.
3- Backup all partitions. Use command  "dd if=/dev/mtd0 of=/tmp/mtd0".
   Copy /tmp/mtd0 to computer using ftp.
4- Copy openwrt-ramips-mt76x8-xiaomi_miwifi-3c-squashfs-sysupgrade.bin
   to /tmp in router using ftp.
5- Enable UART access and change start image for OS1.
```
nvram set uart_en=1
nvram set flag_last_success=1
nvram set boot_wait=on
nvram set flag_try_sys2_failed=1
nvram commit
```
6- Installing Openwrt on OS1 and free OS2.
```
mtd erase OS1
mtd erase OS2
mtd -r write /tmp/openwrt-ramips-mt76x8-xiaomi_miwifi-3c-squashfs-sysupgrade.bin OS1
```

Limitations: For the first install the image size needs to be less
than 7733248 bits.

Thanks for all community and especially for this device:
minax007, earth08, S.Farid

Signed-off-by: Eduardo Santos <edu.2000.kill@gmail.com>
[wrap lines, remove whitespace errors, add mediatek,mtd-eeprom to
 &wmac, convert to nvmem]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-10-31 21:24:47 +01:00
Roger Pueyo Centelles
6801b827e4 ath79: mikrotik: enable SFP on RB921GS-5HPacD (mANTBox 15s)
This patch enables the SFP cage on the MikroTik RouterBOARD 921GS-5HPacD
(mANTBox 15s).

The RB922UAGS-5HPacD had it already working, so the support code is
moved to the common DTSI file both devices share.

Tested on a RouterBOARD 921GS-5HPacD with a MikroTik S-53LC20D module.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2021-10-31 21:24:47 +01:00
Jani Partanen
e06aaba4e3 ramips: fix LAVA LR-25G001 broken wifi led triggers
LED labels for this device are different in 01_leds file and in device
DTS. Switch to DT triggers, which works on Telewell TW-4 (LTE) clone
device.

This has not been tested on the LR-25G001 itself, just on the clone
mentioned above.

Fixes: 20b09a2125 ("ramips: add support for Lava LR-25G001")

Signed-off-by: Jani Partanen <rtfm@iki.fi>
[rephrase commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-10-30 22:11:23 +02:00
Adrian Schmutzler
fbddb38442 ipq806x: consolidate 11-ath10k-caldata
After the ath10k_patch_mac lines have been removed, a lot of blocks
can be consolidated.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-10-30 22:11:23 +02:00
Adrian Schmutzler
6a27e8036e ipq806x: remove transition workarounds for qcom-smem partitions
The out-of-tree qcom-smem patches traditionally displayed mtd partition names
in upper case, starting with the new mainline qcom-smem support in kernel v5.10,
it switched to normalizing the partition names to lower case.

While both 5.4 and 5.10 were supported in the target, we carried a workaround
to support both of them. Since the target has dropped 5.4 recently, those
can be removed now.

Ref:

2db9dded0a ("ipq806x: nbg6817: case-insensitive qcom-smem partitions")
435dc2e77e ("ipq806x: ecw5410: case-insensitive qcom-smem partitions")
f70e11cd97 ("ipq806x: g10: case-insensitive qcom-smem partitions")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-10-30 22:11:23 +02:00
Ansuel Smith
f44e933458 ipq806x: provide WiFI mac-addresses from dts
Use nvmem framework for supported mac-address stored
in nvmem cells and drop mac patch function for hotplug
script for supported devices.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[rebase, move to correct node for d7800, include xr500]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-10-30 22:11:13 +02:00
Michal Kozuch
c12ef2f760 ramips: add support for TP-Link RE305 v3
Specs (same as in v1):
- MT7628AN (575 MHz)
- 64MB RAM
- 8MB of flash (SPI NOR)
- 1x 10/100Mbps Ethernet (MT7628AN built-in switch with vlan)
- 1x 2.4GHz wifi (MT7628AN)
- 1x 5Ghz wifi (MT7612E)
- 4x LEDs (5 GPIO-controlled)
- 1x reset button
- 1x WPS button

The only and important difference between v1 & v3 is in flash memory
layout, so pls don't interchange these 2 builds!

Installation through web-ui (on OEM factory firmware):
1. Visit http://tplinkrepeater.net or the configured IP address of
   your RE305 v3 (default 192.168.0.254).
2. Log in with the password you've set during initial setup of the
   RE305 (there is no default password).
3. Go to Settings -> System Tools -> Firmware upgrade
4. Click Browse and select the OpenWRT image with factory.bin suffix
   (not sysupgrade.bin)
5. A window with a progress bar will appear. Wait until it completes.
6. The RE305 will reboot into OpenWRT and serve DHCP requests on the
   ethernet port.
7. Connect an RJ45 cable from the RE305 to your computer and access
   LuCI at http://192.168.1.1/ to configure (or use ssh).

Disassembly:
Just unscrew 4 screws in the corners & take off the back cover.
Serial is exposed to the right side of the main board (in the middle)
and marked with TX/RX/3V3/GND, but the holes are filled with solder.

Installation through serial:
1. connect trough serial (1n8, baudrate=57600)
2. setup the TFTP server and connect it via ethernet
   (ipaddr=192.168.0.254 of device, serverip=192.168.0.184 - your pc)
3. boot from a initramfs image first (choose 1 in the bootloader
   options)
4. test it a bit with that, then proceed to run sysupgrade build

MAC addresses as verified by OEM firmware:

  use  OpenWrt  address  reference
  LAN  eth0     *:d2     label
  2g   wlan0    *:d1     label - 1
  5g   wlan1    *:d0     label - 2

  The label MAC address can be found in config 0x2008.

Signed-off-by: Michal Kozuch <servitkar@gmail.com>
[redistribute WLAN node properties between DTS/DTSI, remove
 compatible on DTSI, fix indent/wrapping, split out firmware-utils
 change]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-10-30 22:05:25 +02:00
INAGAKI Hiroshi
1b814974e1 build: move elecom-wrc-gs-factory to image-commands.mk
ELECOM WRC-X3200GST3 uses the same header/footer as WRC-GS/GST devices
in ramips/mt7621 subtarget, so move "Build/elecom-wrc-gs-factory" to
image-commands.mk to use from mediatek/mt7622 subtarget.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-10-30 22:05:25 +02:00
Chukun Pan
1b18195f59 sunxi: Nanopi R1S H5: enable LAN LED configuration
This enables the LEDs on the LAN interfaces.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2021-10-30 21:17:20 +02:00
Chukun Pan
fde68cb809 sunxi: add support for FriendlyARM NanoPi R1S H5
Specification:
  CPU: Allwinner H5, Quad-core Cortex-A53
  DDR3 RAM: 512MB
  Network: 10/100/1000M Ethernet x 2
  USB Host: Type-A x 1
  MicroSD Slot x 1
  MicroUSB: for power input
  Debug Serial Port: 3Pin pin-header
  LED: WAN, LAN, SYS
  KEY: Reset
  Power Supply: DC 5V/2A

Installation:
  Write the image to SD Card with dd.

Note:
  1. OpenWrt currently does not support LED_FUNCTION, change back to the
     previous practice (Consistent with NanoPi R1).
  2. Since the upstream commit https://github.com/torvalds/linux/bbc4d71
     ("net: phy: realtek: fix rtl8211e rx/tx delay config"), we need to
     change the phy-mode from rgmii to rgmii-id.
     So set phy-mode for 5.4 and 5.10 respectively.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2021-10-30 21:17:20 +02:00
Chukun Pan
cc2a8c2545 rockchip: move r8152 related patches to generic
These patches can be used on other platforms, so
move it to generic.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2021-10-30 21:17:20 +02:00
Rui Salvaterra
02026d0a6f kernel: bump 5.10 to 5.10.76
Deleted (upstreamed):
bcm27xx/patches-5.10/950-0145-xhci-add-quirk-for-host-controllers-that-don-t-updat.patch [1]

Manually rebased:
bcm27xx/patches-5.10/950-0355-xhci-quirks-add-link-TRB-quirk-for-VL805.patch
bcm53xx/patches-5.10/180-usb-xhci-add-support-for-performing-fake-doorbell.patch

Note: although automatically rebaseable, the last patch has been edited to avoid
conflicting bit definitions.

[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-5.10.y&id=b6f32897af190d4716412e156ee0abcc16e4f1e5

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-10-30 21:17:20 +02:00
Christian Lamparter
fd717f54be ipq40xx: detangle ath10k-board-qca4019 from ath10k-firmware-qca4019*
Back in the day, the board-2.bin came with ath10k-firmware-qca4019.
This changed with
commit c3b2efaf24 ("linux-firmware: ath10k: add board firmware packages")
which placed the board-2.bin into a separate package: ath10k-board-qca4019.
This was great, because it addressed one of the caveat of the original
ipq-wifi package:
commit fa03d441e9 ("firmware: add custom IPQ wifi board definitions")

|  2. updating ath10k-firmware-qca4019 will also replace
|      the board-2.bin. For this cases the user needs to
|      manually reinstall the wifi-board package once the
|      ath10k-firmware-qca4019 is updated.

This could be extended further so that ipq-wifi packages
no longer use "install-override" and the various QCA4019
variants list the ath10k-board-qca4019 as a CONFLICT
package.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-10-30 16:32:59 +02:00
Christian Lamparter
4c8dd973ef ath9k: OF: qca,disable-(2|5)ghz => ieee80211-freq-limit
OpenWrt maintains two special out-of-tree DT properties:
"qca,disable-5ghz" and "qca,disable-2ghz". These are implemented
in a mac80211 ath9k patch "550-ath9k-disable-bands-via-dt.patch".

With the things being what they are, now might be a good
point to switch the devices to the generic and upstream
"ieee80211-freq-limit" property. This property is much
broader and works differently. Instead of disabling the
drivers logic which would add the affected band and
channels. It now disables all channels which are not
within the specified frequency range.

Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> # HH5A
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-10-30 16:32:59 +02:00
Bjørn Mork
d990f805c0 realtek: re-enable IPv6 routing
Commit 03e1d93e07 ("realtek: add driver support for routing
offload") added routing offload for IPv4, but broke IPv6 routing
completely.  The routing table is empty and cannot be updated:

 root@gs1900-10hp:~# ip -6 route
 root@gs1900-10hp:~# ip -6 route add unreachable default
 RTNETLINK answers: Invalid argument

As a side effect, this breaks opkg on IPv4 only systems too,
since uclient-fetch fails when there are no IPv6 routes:

 root@gs1900-10hp:~# uclient-fetch http://192.168.99.1
 Downloading 'http://192.168.99.1'
 Failed to send request: Operation not permitted

Fix by returning NOTIFY_DONE when offloading is unsupported, falling
back to default behaviour.

Fixes: 03e1d93e07 ("realtek: add driver support for routing offload")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-10-30 15:00:22 +02:00
Bjørn Mork
daefc646e6 realtek: fix ZyXEL initramfs image generation
The current rule produces empty trailers, causing the OEM firmware
update application to reject our images.

The double expansion of a makefile variable does not work inside
shell code.  The second round is interpreted as a shell expansion,
attempting to run the command ZYXEL_VERS instead of expanding the
$(ZYXEL_VERS) makefile variable.

Fix by removing one level of variable indirection.

Fixes: c6c8d597e1 ("realtek: Add generic zyxel_gs1900 image definition")
Tested-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-10-30 15:00:22 +02:00
Christian Lamparter
6102f883ce bcm53xx: MR32: replace i2c-gpio with SoC's i2c
During review of the MR32, Florian Fainelli pointed out that the
SoC has a real I2C-controller. Furthermore, the connected pins
(SDA and SCL) would line up perfectly for use. This patch swaps
out the the bitbanged i2c-gpio with the real deal.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-10-30 15:00:22 +02:00
Daniel Golle
f5d071a508
sunxi: deselect CONFIG_VIDEO_SUN6I_CSI by default
Deselect CONFIG_VIDEO_SUN6I_CSI Kconfig symbol for now. If anyone wants
to use CSI (camera interface) they should package the kernel module.
After this change, sunxi targets build again.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-10-29 18:44:15 +01:00
Daniel Golle
1175e786f8
sunxi: add CONFIG_ARM_CRYPTO Kconfig symbol
And another missing symbol...

Reported-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-10-29 18:44:09 +01:00
Daniel Golle
3c33ed02c2
sunxi: add yet another missing Kconfig symbol
Set CONFIG_CRYPTO_CRCT10DIF_ARM_CE=y for sunxi targets.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-10-29 18:25:27 +01:00
Rafał Miłecki
a2f5a83af8 bcm53xx: backport patch fixing pinctrl driver
This switches pinctrl driver to use the old & good DT binding. There is
no more need to adjust upstream DTS file.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-10-29 15:30:47 +02:00
Daniel Golle
524c687e05
sunxi: add missing CONFIG_VIDEO_SUN4I_CSI Kconfig symbol
Simply disable this for now, if anyone wants to use CSI feel free to
package it as a kernel module package.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-10-29 14:21:27 +01:00
Daniel Golle
4ae4035e60
mediatek: make sure MMC is not busy before commencing sysupgrade
In case of the block device still being in use, re-reading the
partition table fails. In that case, abort sysupgrade to avoid
corrupting the just-written image because of wrong offsets caused
by failure to re-read the partition table.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-10-28 16:27:27 +01:00
Peter Geis
70c12d26ca ipq806x: add support for Netgear Nighthawk Pro Gaming XR500
This adds support for the Netgear Nighthawk Pro Gaming XR500.
It is the successor to the Netgear Nighthawk R7800 and shares almost
identical hardware to that device.
The stock firmware is a heavily modified version of OpenWRT.

Specifications:
  SoC: Qualcomm Atheros IPQ8065
  RAM: 512 MB
  Storage: 256 MiB NAND Flash
  Wireless: 2x Qualcomm Atheros QCA9984
  Ethernet: 2x 1000/100/10 dedicated interfaces
  Switch: 5x 1000/100/10 external ports
  USB: 2x 3.0 ports

More information:
Manufacturer page: https://www.netgear.com/gaming/xr500/
Almost identical to Netgear R7800
Differences (r7800 > xr500):
  Flash: 128MiB > 256MiB
  Removed esata
  swapped leds:
    usb1 (gpio 7 > 8)
    usb2 (gpio 8 > 26)
    guest/esata (gpio 26 > 7)

MAC addresses:

On the OEM firmware, the mac addresses are:

  WAN: *:50  art 0x6
  LAN: *:4f  art 0x0 (label)
  2G:  *:4f  art 0x0
  5G:  *:51  art 0xc

Installation:
Install via Web Interface (preferred):
Utilize openwrt-ipq806x-netgear_xr500-squashfs-factory.img

Install via TFTP recovery:
1.Turn off the power, push and hold the reset button (in a hole on
  backside) with a pin
2.Turn on the power and wait till power led starts flashing white
  (after it first flashes orange for a while)
3.Release the reset button and tftp the factory img in binary mode.
  The power led will stop flashing if you succeeded in transferring
  the image, and the router reboots rather quickly with the new
  firmware.
4.Try to ping the router (ping 192.168.1.1). If does not respond,
  then tftp will not work either.

Uploading the firmware image with a TFTP client
$ tftp 192.168.1.1
bin
put openwrt-ipq806x-netgear_xr500-squashfs-factory.img

Note:

The end of the last partition is at 0xee00000. This was chosen
by the initial author, but nobody was able to tell why this
particular arbitrary size was chosen. Since it's not leaving
too much empty space and it's the only issue left, let's just
keep it for now.

Based on work by Adam Hnat <adamhnat@gmail.com>
ref: https://github.com/openwrt/openwrt/pull/3215

Signed-off-by: Peter Geis <pgwipeout@gmail.com>
[squash commits, move common LEDs to DTSI, remove SPDX on old
 files, minor whitespace cleanup, commit message facelift,
 add MAC address overview, add Notes, fix MAC addresses,
 use generic name for partition nodes in DTS]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-10-26 22:30:18 +02:00
Bruno Randolf
2c3e8bed3f
ramips: minew g1-c: Allow dynamic RAM sizes
Allow RAM size to be passed thru U-Boot. There are 128MB and 64MB
versions of Minew G1-C. This is also in line with the behaviour of
most other RAMIPS boards.

Signed-off-by: Bruno Randolf <br1@einfach.org>
2021-10-26 13:59:30 +02:00
Paul Spooren
abd67de9f0 sunxi: switch to Kernel 5.10
Compile tested and run tested on Pine64+.

Acked-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Paul Spooren <mail@aparcar.org>
2021-10-25 10:28:07 -10:00
Hauke Mehrtens
a1939e7e37 kernel: Add extra configuration options
These options show up when compiling the at91 target.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-10-24 20:22:04 +02:00
Claudiu Beznea
8746ba3657 at91: add support for sam9x60-ek board
Add support for SAM9X60-EK board.

Hardware:
- SoC: SAM9X60
- RAM: Winbond W972GG6KB-25 (2Gbit DDR2)
- NAND Flash: Micron MT29F4G08ABAEA
- QSPI Flash: Microchip SST26VF064B
- EEPROM: Microchip 24AA02E48
- SDMMC: One standard 4-bit SD card interface
- USB: two stacked Type-A connectors with power switches, one micro-B
       USB device
- CAN: 2 interfaces (Microchip MCP2542)
- Ethernet: one 10/100Mbps
- WiFi/BT: one optional WiFi/Bluetooth interface
- Audio: one ClassD port
- Display: one 24-bit LCD interface
- Camera: one 12-bit image sensor interface
- IO: one IO expander (Microchip MCP23008)
- Debug ports: one J-Link-OB + CDC, one JTAG interface
- Leds: one RGB LED
- Buttons: 4 push button switches
- Expansion: one PIO connector, one mikrobus connector
- Power management: two power regulators, two power consumption measurement
                    devices

Flashing:
- follow the procedure at [1]

[1] https://www.linux4sam.org/bin/view/Linux4SAM/Sam9x60EKMainPage#Create_a_SD_card_with_the_demo

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
2021-10-24 18:52:29 +02:00
Claudiu Beznea
65c4e89dcf at91: enable kernel config for sam9x60
Enable kernel config for SAM9X60.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
2021-10-24 18:52:25 +02:00
Claudiu Beznea
60f52f9b0d at91: add support for sama5d27-wlsom1-ek board
Add support for SAMA5D27 WLSOM1-EK board.

Hardware:
- SIP: SAMA5D27C-LD2G-CU including SAMA5D27 MPU and 2Gbit LPDDR2-SDRAM
- MMC: one standard SD card interface
- Flash: 64 Mb serial quad I/O flash memory (SST26VF064BEUIT-104I/MF)
	 with embedded EUI-48 and EUI-64 MAC addresses
- USB: one USB device, one USB host one HSIC interface
- Ethernet: 1x10/100Mbps port
- WiFi/BT: IEEE 802.11 b/g/n Wi-Fi plus Bluetooth (Wi-Fi/BT) module
	   (ATWILC3000-MR110UA)
- Crypto: one ATECC608B-TNGTLS secure element
- Video: one LCD RGB 18-bit interface, one ISC 12-bit camera interface
- Debug port: one JTAG interface, one UART interface, one WILC UART
              interface
- Leds: one RGB LED
- Buttons: start, reset, wakeup, user buttons
- Expansion: one tamper connector, one mikrobus interface, 2 XPRO PTC
             connector
- Power managament: PMIC (MCP16502)

Flashing:
- follow procedure at [1]

[1] https://www.linux4sam.org/bin/view/Linux4SAM/Sama5d27WLSom1EKMainPage#Create_a_SD_card_with_the_demo

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
2021-10-24 18:52:21 +02:00
Claudiu Beznea
8b7e577f76 at91: add support for sama5d2 icp board
Add support for SAMA5D2 ICP board.

Hardware:
- SoC: SAMA5D27
- RAM: 512 MB DDR3L
- MMC: One stanard SD card interface
- USB: One USB host switch 4 ports with power switch,
       One USB device type Micro-AB
- CAN: 2 interfaces
- Ethernet: One Gigabit Ethernet PHY through HSIC,
	    One ETH switchport,
	    One EtherCAT interface
- WiFi/BT: Footprint for IEEE 802.11 b/g/n Wi-Fi plus
	   Bluetooth module (Wi-Fi/BT), suitable for
	   Microchip WILC3000-MR110CA or WILC3000-MR110UA
- Debug port: One J-Link-OB/J-Link-CDC, one JTAG interface
- Leds: one RGB LED
- Buttons: reset, wakeup, 2 user buttons
- Expansion: one PIOBU/PIO connector, 3 mikrobus sockets
- Power mangament: PMIC (MCP16502), one power consumption device
                   (PAC1934)

Not working in Linux:
- EtherCAT interface: there is no Linux support integrated
- PAC1934: driver available at [1] but not integrated in Linux

Flashing:
- follow the procedure at [2]

[1] https://ww1.microchip.com/downloads/en/DeviceDoc/pac193x_linux_driver.zip
[2] https://www.linux4sam.org/bin/view/Linux4SAM/Sama5d2IcpMainPage#Create_a_SD_card_with_the_demo

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
2021-10-24 18:52:17 +02:00
Claudiu Beznea
999c925f9d at91: enable specific sam9x kernel config flags
Enable specific sam9x kernel config flags.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
2021-10-24 18:52:12 +02:00
Claudiu Beznea
7bd0fba3df at91: kernel: bump to 5.10
Bump at91 targets to kernel v5.10. With this patches and files for
wb45n and wb50n were removed as they are now included in upstream
kernel. Along with:
- this the kernel config for sama5d2 and sam9x targets has been
  refreshed (with make kernel_menuconfig + save);
- CONFIG_ARCH_AT91 and specific sam9x SoCs (AT91RM9200, AT91SAM9,
  SAM9X60) has been enabled such that sam9x SoCs to be able to boot.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
2021-10-24 18:52:06 +02:00
Chukun Pan
d9a580eb2e sunxi: 5.10: enable sun8i-thermal
Enable the sun8i-thermal driver to allow reading the
temperature of the SoC.

As suggested by mans0n, disable this driver in the
a8 subtarget because it does not support yet.

Tested on NanoPi R1S H5.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2021-10-24 18:44:41 +02:00
Matthew Hagan
b428f187f0 kernel: 5.10: qca8k: backport qca8k_setup tidy-up
Tidy qca8k_setup for loops relating to port handling. No functional
changes.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
2021-10-24 16:56:17 +02:00
Matthew Hagan
ae77a466e4 kernel: 5.10: backport qca8k cpu_port_index fix in parse_port_config
Add cpu_port_index fix to apply settings to correct CPU port.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
2021-10-24 16:56:17 +02:00
Matthew Hagan
f97cafdd1d kernel: 5.10: backport qca8k feature additions
Backport Ansuel Smith's various qca8k feature additions:
- mac-power-sel support
- SGMII PLL explicit enable
- tx/rx clock phase to falling edge
- power-on-sel and LED open drain mode
- cpu port 6
- qca8328 support
- sgmii internal delay
- move port config to dedicated struct
- convert to yaml schema

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
2021-10-24 16:56:17 +02:00
Matthew Hagan
d888ef5668 kernel: 5.10: backport QCA83x PHY resume fix, DAC amplitude preferred master, debug reg names
Backport workaround for QCA8327 PHY resume, which does not properly support
genphy_suspend/resume. Also add DAC amplitude fix for the QCA8327 PHY,
set port to preferred master and add proper names to debug regs.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
2021-10-24 16:56:17 +02:00
Matthew Hagan
dee819272a kernel: 5.10: backport at803x QCA83xx phy support improvements
This commit add accepted upstream patches that improve & tidy qca83xx support.
1 - Split qca8327 to A & B variants, identifiable by phy_id
2 - Add suspend/resume support to qca8xx phys
3 - Tidy spacing and phy naming.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
2021-10-24 16:56:17 +02:00
Matthew Hagan
3cee66cd37 kernel: 5.10: backport at803x internal QCA8327 PHY support
Add support for qca8327 internal phy needed for correct init of the
switch port. It does use the same qca8337 function and reg just with a
different id.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
2021-10-24 16:56:17 +02:00
Matthew Hagan
8cd974dc40 kernel: 5.10: backport qca8k legacy mdio mapping panic fix
Add backport of Ansuel Smith's "net: dsa: qca8k: fix kernel panic with
legacy mdio mapping" patch.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
2021-10-24 16:56:17 +02:00
Matthew Hagan
c757c71fd1 kernel: 5.10: backport additional qca8k fixes
Backport fixes including:
net: dsa: qca8k: fix missing unlock on error in qca8k_vlan_(add|del)
net: dsa: qca8k: check return value of read functions correctly
net: dsa: qca8k: add missing check return value in qca8k_phylink_mac_config()
net: dsa: qca8k: fix an endian bug in qca8k_get_ethtool_stats()
net: dsa: qca8k: check the correct variable in qca8k_set_mac_eee()

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
2021-10-24 16:56:17 +02:00
Matthew Hagan
e3c47ff90d kernel: 5.10: backport qca8k stability improvements
This is a backport of Ansuel Smith's "Multiple improvement to qca8k stability"
series. The QCA8337 switch is available on multiple platforms including
ipq806x, ath79 and bcm53xx.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
2021-10-24 16:56:17 +02:00
Christian Lamparter
36104dc51f kernel: 5.10: silence bogus "Missing #address-cells in interrupt provider" warnings
Rosen reported strange dtc warnings that had their origin in
an upstream patch to 5.8-rc1. Upon further digging this
revealed an ongoing thread [0] discussing the topic:

> [...]I don't think we need a bunch of warning fix patches to add
> these everywhere. Also, the need for #address-cells pretty much makes
> no sense on any modern system. It is a relic from days when the bus
> (address) topology and interrupt topology were related.

and later on:
> So really, we only need to be checking for #address-cells in nodes
> with interrupt-map.

This patch backports just the patch which removed the warning message
(this is from the upstream dtc project [1] - but not the kernel).
the patch does not add the checking of the #address-cells in nodes
with interrupt-map.

[0] <https://lore.kernel.org/linux-devicetree/91e3405245c89f134676449cf3822285798d2ed2.1612189652.git.michal.simek@xilinx.com/>
[1] <https://git.kernel.org/pub/scm/utils/dtc/dtc.git/commit/?id=d8d1a9a77863a8c7031ae82a1d461aa78eb72a7b>
Link: <https://github.com/openwrt/openwrt/pull/4685>
Reported-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-10-24 11:20:22 +02:00
Sven Eckelmann
ac4a21141a ath79: ag71xx: Disable napi related interrupts during probe
ag71xx_probe is registering ag71xx_interrupt as handler for the gmac0/gmac1
interrupts. The handler is trying to use napi_schedule to handle the
processing of packets. But the netif_napi_add for this device is
called a lot later in ag71xx_probe.

It can therefore happen that a still running gmac0/gmac1 is triggering the
interrupt handler with a bit from AG71XX_INT_POLL set in
AG71XX_REG_INT_STATUS. The handler will then call napi_schedule and the
napi code will crash the system because the ag->napi is not yet
initialized:

  libphy: Fixed MDIO Bus: probed
  CPU 0 Unable to handle kernel paging request at virtual address 00000000, epc == 00000000, ra == 81373408
  Oops[#1]:
  CPU: 0 PID: 1 Comm: swapper Not tainted 5.4.152 #0
  $ 0   : 00000000 00000001 00000000 8280bf28
  $ 4   : 82a98cb0 00000000 81620000 00200140
  $ 8   : 00000000 00000000 74657272 7570743a
  $12   : 0000005b 8280bdb9 ffffffff ffffffff
  $16   : 00000001 82a98cb0 00000000 8280bf27
  $20   : 8280bf28 81620000 ffff8b00 8280bf30
  $24   : 00000000 8125af9c
  $28   : 82828000 8280bed8 81610000 81373408
  Hi    : 00005fff
  Lo    : 2e48f657
  epc   : 00000000 0x0
  ra    : 81373408 __napi_poll+0x3c/0x11c
  Status: 1100dc03 KERNEL EXL IE
  Cause : 00800008 (ExcCode 02)
  BadVA : 00000000
  PrId  : 00019750 (MIPS 74Kc)
  Modules linked in:
  Process swapper (pid: 1, threadinfo=(ptrval), task=(ptrval), tls=00000000)
  Stack : ffff8afb ffff8afa 81620000 00200140 00000000 82a98cb0 00000008 0000012c
          81625620 81373684 ffffffff ffffffff ffffffef 00000008 816153d8 81620000
          815b0d60 815bbd54 00000000 81753700 8280bf28 8280bf28 8280bf30 8280bf30
          81753748 00000008 00000003 00000004 0000000c 00000100 3fffffff 8175373c
          816059f0 814ddb48 00000001 8160ab30 81615488 810618bc 00000006 00000000
          ...
  Call Trace:

  [<81373684>] net_rx_action+0xfc/0x26c
  [<814ddb48>] __do_softirq+0x118/0x2ec
  [<810618bc>] handle_percpu_irq+0x50/0x80
  [<8125ab8c>] plat_irq_dispatch+0x94/0xc8
  [<81004e98>] handle_int+0x138/0x144

  Code: (Bad address in epc)

  ---[ end trace a60d797432b656b2 ]---

The gmcc0/gmac1 must be brought in a state in which it doesn't signal a
AG71XX_INT_POLL related status bits as interrupt before registering the
interrupt handler. ag71xx_hw_start will take care of re-initializing the
AG71XX_REG_INT_ENABLE.

Fixes: f529a37420 ("surprise :p")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2021-10-23 18:50:31 +02:00
Rosen Penev
360c181dd7 kernel: backport GPIO LED patch for MT7530
This allows to specify and control switch LEDs on devices using mt7530
(typically mediatek and ramips targets).

Normally these LED GPIOs are 0, 3, 6, 9, and 12. wan/lan assignment is
per device. GPIO 9 is normally inverted. so GPIO_ACTIVE_HIGH instead of
GPIO_ACTIVE_LOW.

Tested on Linksys E7350.

Refreshed all patches.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2021-10-23 18:50:31 +02:00
Tan Zien
85a42fa9cb ipq40xx: MR33: Fix LP5562 LED driver probe
Add the reg and color property to each channel node. This update is
to accommodate the multicolor framework.

Refer to:
<https://lore.kernel.org/all/20200622185919.2131-9-dmurphy@ti.com>
<https://lore.kernel.org/all/20210818070209.1540451-1-michal.vokac@ysoft.com>

Signed-off-by: Tan Zien <nabsdh9@gmail.com>
[replaced links to lore, wrote something of a commit message]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-10-23 18:50:25 +02:00
Hauke Mehrtens
9501ce909f layerscape: Fix build in dtb
This fixes a kernel build problem.
The removed parts of the patch are already applied upstream.

Fixes: 9ad3ef27b9 ("kernel: bump 5.4 to 5.4.153")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-10-22 22:12:24 +02:00
Christian Lamparter
9fcb5c367e apm821xx: WNDAP6X0: add missed uci-default for compat
This should have been included in the previous patch that
resized the kernel partition to fit bigger kernels.

Fixes: 7a6a349445 ("apm821xx: WNDAP620 + WNDAP660: reorganize partitions for 5.10")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-10-22 21:25:18 +02:00
Christian Lamparter
8b0c053671 apm821xx: implement new LED label naming scheme
This patch updates all current APM82181 devices over to that
"new LED naming scheme". This includes many updates to the
device-tree:
	- dropped the deprecated, but beloved "label" property.
	- rename all DT leds node names to led-#.
	- add function and color properties.
	- utilized panic-indicator property.
	- dropped led- aliases (see below).

migration scripts for all devices are included.

For more information. See:
<https://www.kernel.org/doc/html/latest/leds/leds-class.html>

For the future: It looks like the color+function properties
won over the dt-alias / label. This will need to be wired up
into openwrt eventually. For APM821xx the situation is that
all devices have a dedicated power and fault indicator.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-10-22 21:25:18 +02:00
Christian Lamparter
e9335c2920 ath79: lzma-loader: fix & re-enable per-board CONFIG_BOARD_DEV
Back in the AR71XX days, the lzma-loader code could be customized
based on the $BOARD variable. These would be passed as a
compile-time -DCONFIG_BOARD_$DEVICE_MODEL flag to the compiler.
Hence, the lzma-loader would be able to include device-specific
fixups.

Note: There's still a fixup for the TpLink TL-WR1043ND V1 found
in the lzma-loader's board.c code. But since the days of AR71XX
I couldn't find a forum post or bug reported. So, I left it
as is to not break anything by enabling it.

=> If you have a TL-WR1043ND V1 and you have problem with
the ethernet: let me know. Because otherwise, the fixup
might simply no longer needed with ath79 and it can be removed.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-10-22 21:25:18 +02:00
Christian Lamparter
8a042450d8 apm821xx: MX60(W): re-enable + allow bigger future kernels
The MX60's kernel is limited to 0x3EFC00 by the values in
mkmerakifw.c. Since the initramfs method of loading the
kernel seems to be working, this patch does away with the
use of the mkmerakifw tool for the MX60(W).

But this will go along with a change in u-boot as well.
So before you upgrade, please attach the serial cable and
perform:

| setenv owrt510_boot run meraki_ubi owrt_bootargs\; run owrt_load1 owrt_bootkernel\; run owrt_load2 owrt_bootkernel
| setenv bootcmd run owrt510_boot
| saveenv

Note: You won't be able to use older OpenWrt releases without
switching the bootcmd back to owrt_boot!

Note2: We are no longer compatible with older OpenWrt MX60 installs.
the legacy BOARD_NAME and SUPPORTED_DEVICES can be dropped. This is
because upgrades from older images are not possible without uboot env
changes anymore. Also the bogus BLOCKSIZE value
(which was set to 63k back then, in order to get the kernel properly
aligned after the fdt + meraki header) can be set to the NANDs real
value. The FDT size (which was needed for alignment) can now be
slimmed down as well.

Co-developed-by: Martin Kennedy <hurricos@gmail.com>
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-10-22 21:25:18 +02:00
Christian Lamparter
bbb3852401 apm821xx: MBL: HDD regulators overhaul for MBL DUO
Takimata reported on the OpenWrt forum in thread [0], that his
MyBook Live Duo wasn't booting OpenWrt 21.02 after upgrading
from the previous OpenWrt 19.07.

The last logged entries on his console

|[    0.531599] sata1-regulator GPIO handle specifies active low - ignored
|[    0.538391] sata0-regulator GPIO handle specifies active low - ignored
|[    0.759791] ata2: SATA link down (SStatus 0 SControl 300)
|[    0.765251] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
|[    5.909555] ata1.00: qc timeout (cmd 0xec)
|[    5.913656] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
|[    6.231757] ata1: SATA link down (SStatus 0 SControl 300)

This extract clearly showed that the HDD on which OpenWrt is installed,
simply disappeared after the SATA power regulators had been initialized.

The reason why this worked with OpenWrt 19.07 was because the kernel
config symbol CONFIG_REGULATOR=y was not set in the target's config-4.14.

(This shows that the MBL Single does differ from the DUO in that
it does not have programmable power regulators for the HDDs.)

[0] <https://forum.openwrt.org/t/21-02-0-and-snapshot-fail-to-boot-on-my-book-live-duo/106585>

Reported-by: Takimata (forum)
Tested-by: Takimata (forum)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-10-22 21:25:18 +02:00
Roger Pueyo Centelles
68d91f08ed ath79: mikrotik: use 64 KiB SPI NOR erase sectors
This patch removes CONFIG_MTD_SPI_NOR_USE_4K_SECTORS from the default
symbols for the ath79/mikrotik target.

MikroTik devices hold some of their user-configurable settings in the
soft_config partition, which is typically sized 4 KiB, of the SPI NOR
flash memory. Previously, in the ar71xx target, it was possible to use
64 KiB erase sectors but also smaller 4 KiB ones when needed. This is
no longer the case in ath79 with newer kernels so, to be able to write
to these 4 KiB small partitions without erasing 60 KiB around, the
CONFIG_MTD_SPI_NOR_USE_4K_SECTORS symbol was added to the defaults.
However, this ended up making sysupgrade images which were built with
64 KiB size blocks not to keep settings (e.g., the files under
/etc/config/) over the flashing process.

Using 4 KiB erase sector size on the sysupgrade images (by setting
BLOCKSIZE = 4k) allows keeping settings over a flashing process, but
renders the process terribly slow, possibly causing a user to
mistakenly force a manual device reboot while the process is still on-
going. Instead, ditching the 4 KiB erase sectors for the default
64 KiB erase size provides normal SPI write speed and sysupgrade times,
at the expense of not being able to modify the soft_config partition
(which is rarely a required thing).

An OpenWrt patch for MTD_SPI_NOR_USE_4K_SECTORS_LIMIT may once have
allowed to use different per-partition erase sector sizes. Due to
changes on recent kernels it now only works on a per-device basis.
Also, partial eraseblock write can be performed in ath79 with kernels
5.4 and lower, by copying the blocks from the 64 KiB, erasing the whole
sector and restoring those blocks not meant to be modified. A kernel
bump had that patch broken for a long time, but got fixed in bf2870c.

Note: the settings in the soft_config partition can be reset to their
defaults by holding the reset button for 5 seconds (and less than 10
seconds) at device boot.

Fixes: FS#3492 (sysupgrade […] loses settings...)
Fixes: a66eee6336 (ath79: add mikrotik subtarget)

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2021-10-22 08:15:40 -10:00
Rafał Miłecki
b8e682ac74 bcm53xx: bridge all LAN ports on Linksys EA9500
External switch ports need to be bridged too.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-10-22 13:46:22 +02:00
Paul Spooren
f46a70a688 toolchain: switch packaged toolchain to tar.xz
Currently the tar.bz2 while ImageBuilder and SDK switched to tar.xz.
Unify it for faster compression since it will make use of
multi-threading.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2021-10-21 08:25:38 -10:00
Rafał Miłecki
e9672b1a8f bcm53xx: switch to the upstream DSA-based b53 driver
1. Drop swconfig
2. Simplify network setup
3. Verify network config
4. Disable Buffalo WZR-900DHP for now - it misses ports definition

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-By: Christian Lamparter <chunkeey@gmail.com>
2021-10-21 17:38:17 +02:00
Rafał Miłecki
d88f3b8a42 bcm47xx: add kernel 5.10 support
It's for *development* only as it doesn't work with lzma-loader due to
bigger size.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-10-21 17:38:17 +02:00
David Bauer
f85c970c9c ath79: use correct USB package for DIR-505
AR9331 requires kmod-usb2-chipidea to use the USB ports. Include the
correct package so they can be used with the base image.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-10-21 15:52:49 +02:00
Robert Marko
b519997ab9 kernel: 5.10: backport Marvell 88E1510/2 PHY SFP support
Backport upstream SFP support for the Marvell 88E1510/2 PHY-s.

Globalscale MOCHAbin uses this PHY for the hybrid
WAN port that has 1G SFP and 1G RJ45 with PoE PD
connected to it.

This allows the SFP port to be used on it as well as
parsing the SFP module details with ethtool.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2021-10-21 00:17:36 +02:00
Robert Marko
b0f6162d68 kernel: 5.10: backport 100 BaseX SFP support
Backport upstream support for 100Base-FX, 100Base-LX, 100Base-PX and
100Base-BX10 SFP modules.

This is a prerequisite for the Globalscale MOCHAbin hybrid 1G
SFP/Copper support backporting.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2021-10-21 00:17:36 +02:00
Rui Salvaterra
d4f0e45f90 kernel: bump 5.10 to 5.10.75
Deleted (upstreamed):
bcm27xx/patches-5.10/950-0735-xhci-guard-accesses-to-ep_state-in-xhci_endpoint_res.patch [1]

[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-5.10.y&id=dc3e0a20dbb9dbaa22f4a33dea34230f8c663c40

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-10-21 00:17:36 +02:00
Rui Salvaterra
72e53eb133 kernel: bump 5.10 to 5.10.74
Patches automatically refreshed.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-10-21 00:17:36 +02:00
Rui Salvaterra
3bd701d47c kernel: bump 5.10 to 5.10.73
Patches automatically refreshed.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-10-21 00:17:36 +02:00
John Audia
0ea33e5363 kernel: bump 5.4 to 5.4.155
All patches automatically rebased.

Signed-off-by: John Audia <graysky@archlinux.us>
2021-10-21 00:17:36 +02:00
John Audia
3d0499bcdb kernel: bump 5.4 to 5.4.154
All patches automatically rebased.

Signed-off-by: John Audia <graysky@archlinux.us>
2021-10-21 00:17:36 +02:00
John Audia
9ad3ef27b9 kernel: bump 5.4 to 5.4.153
Removed upstreamed:
  backport-5.4/070-v5.5-MIPS-BPF-Restore-MIPS32-cBPF-JIT.patch

All other patches automatically rebased.

Signed-off-by: John Audia <graysky@archlinux.us>
2021-10-21 00:17:36 +02:00
Adrian Schmutzler
352427ecec realtek: switch to kernel 5.10
The usual testers did their tests. Now we need testers who use the
master builds.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-10-20 23:27:52 +02:00
Adrian Schmutzler
7b8eca902e tegra: switch to kernel 5.10
This target has testing support for kernel 5.10 for four months now.
Time to switch the default.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Tomasz Maciej Nowak <tmn505@gmail.com>
2021-10-18 21:32:36 +02:00
Rafał Miłecki
287257d676 bcm53xx: enable Linksys EA6300 & EA9200 builds
Both should be supported since:
1. Adding NVMEM driver for NVRAM
2. Using NVRAM info for determining active firmware partition

Linksys EA9500 uses very similar design and works fine.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-10-18 16:09:36 +02:00
Felix Fietkau
a1ac8728f8 ramips: remove kmod-mt7663-firmware-sta from device packages
This firmware should only be used for mobile devices (e.g. laptops), where
AP mode functionality is typically not used. This firmware supports a lot
of power saving offload functionality at the expense of AP mode support.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-10-17 16:07:03 +02:00
Rosen Penev
5b3d62247c ramips: fix dtc warnings for telco-electronics_x1
In all other dts files, the entire block is not edited like this.
They're edited separately.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2021-10-17 15:21:37 +02:00
Luis Araneda
88537e76ec zynq: switch to kernel 5.10
Use kernel 5.10 by default

compile-tested: all devices from target (wth ALL_KMODS)
run-tested: Digilent Zybo Z7-20

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2021-10-17 14:13:22 +02:00
Luis Araneda
16ba7ca8be zynq: kernel: update config for 5.10
Update config with make kernel_oldconfig

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2021-10-17 14:13:22 +02:00
Luis Araneda
861ff4d080 zynq: kernel: copy config from 5.4 to 5.10
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2021-10-17 14:13:22 +02:00
Luis Araneda
97a427412a zynq: kernel: remove wireless extensions symbols
This fixes compilation of several wireless drivers that
require support for the old wireless extension to work.
One example is kmod-hermes.

The symbols are set to "y" on generic configuration.
But they were wrongly disabled on the target-specific
configuration.

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2021-10-17 14:13:22 +02:00
Luis Araneda
b898e869e2 zynq: kernel: refresh config
using "make kernel_oldconfig"

Several configs are now part of generic

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2021-10-17 14:13:22 +02:00
Daniel Golle
3a93704a63
mediatek: add EEPROM data for BPi-R64 2.4GHz wmac
EEPROM data extracted from vendor image found at
http://forum.banana-pi.org/t/bpi-r64-mt7622-mac80211-wifi-driver/10246/77
http://forum.banana-pi.org/uploads/short-url/jworbyBYpvrw9VQ2sx92B9z6DWS.bin

MAC address in the EEPROM has been zero'd which results in random
address on boot.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-10-15 00:12:30 +01:00
Felix Fietkau
f2e1e156c0 kernel: backport a rewrite of the mips eBPF JIT implementation
This adds support for eBPF JIT for 32 bit targets and significantly improves
correctness.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-10-14 20:29:51 +02:00
Paul Spooren
e07cc46991 x86/64: enable MMIO_CMDLINE_DEVICES for firecracker support
This Kernel option allows to run OpenWrt witin a `firecracker` micro VM.

Firecracker is a KVM-based tool for superfast booting VMs on x86_64 and
aarch64. It makes rootfs available to the guest as a virtio-mmio device
and passes its address via the kernel cmdline. A kernel without
CONFIG_VIRTIO_MMIO_CMDLINE_DEVICES will not recognize the rootfs
virtio-mmio device.

Suggested-by: Packet Please <pktpls@systemli.org>
Signed-off-by: Paul Spooren <mail@aparcar.org>
2021-10-12 19:22:19 -10:00
Paul Spooren
4056a40160 armvirt: enable MMIO_CMDLINE_DEVICES for firecracker support
This Kernel option allows to run OpenWrt witin a `firecracker` micro VM.

Firecracker is a KVM-based tool for superfast booting VMs on x86_64 and
aarch64. It makes rootfs available to the guest as a virtio-mmio device
and passes its address via the kernel cmdline. A kernel without
CONFIG_VIRTIO_MMIO_CMDLINE_DEVICES will not recognize the rootfs
virtio-mmio device.

Suggested-by: Packet Please <pktpls@systemli.org>
Signed-off-by: Paul Spooren <mail@aparcar.org>
2021-10-12 19:22:08 -10:00
Christian Lamparter
80b7a8a7f5 Revert "gpio-cdev: add nu801 userspace driver"
This reverts commit f536f5ebdd.

As Hauke commented, this causes builder failures on 5.4 kernels.
This revert includes changes to the mx100 kernel modules
dependency as well as the uci led definitions.

Tested-by: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-10-10 23:15:05 +02:00
Szabolcs Hubai
81d694e30b ipq40xx: use zImage for GL.iNet GL-B1300, GL-S1300 to shrink below 4096k
In the "ipq40xx: switch to Kernel 5.10" discussion at GitHub,
Adrian noted [0] that these GL.iNet Conexa series devices,
GL-B1300 and GL-S1300 failed their image generation [1] as their gzipped
uImage kernel went above 4096k.

While notifying the vendor about this problem [2], I tested all U-Boot
releases from GL.iNet:
- they really fail to boot kernel above 4096k
- they don't support lzma: "Unimplemented compression type 3"
- but they boot zImage

Using zImage (xz compression) the kernel is 2909k which is
more than a megabyte away from the KERNEL_SIZE := 4096k limit.

The gzip compressed version would be 4116k.

[0]: https://github.com/openwrt/openwrt/pull/4620#issuecomment-932765776
[1]: commit 7b1fa276f5 ("ipq40xx: add testing support for kernel 5.10")
[2]: https://forum.gl-inet.com/t/ipq40xx-kernel-size-and-u-boot-v5-10-is-too-big-for-4-mb/17619

Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
2021-10-10 16:47:41 +02:00
Chris Blake
fe9e5fbd75 x86: add support for Meraki MX100
This commit will add support for the Meraki MX100 in OpenWRT.

Specs:
* CPU: Intel Xeon E3-1200 Series 1.5GHz 2C/4T
* Memory: 4GB DDR3 1600 ECC
* Storage: 1GB USB NAND, 1TB SATA HDD
* Wireless: None
* Wired: 10x 1Gb RJ45, 2x 1Gb SFP

UART:
The UART header is named CONN11 and is found in the
center of the mainboard. The pinout from Pin 1 (marked
with a black triangle) to pin 4 is below:
Pin 1: VCC
Pin 2: TX
Pin 3: RX
Pin 4: GND
Note that VCC is not required for UART on this device.

Booting:
1. Flash/burn one of the images from this repo to a
flash drive.
2. Take the top off the MX100, and unplug the SATA
cable from the HDD.
3. Hook up UART to the MX100, plug in the USB drive,
and then power up the device.
4. At the BIOS prompt, quickly press F7 and then
scroll to the Save & Exit tab.
5. Scroll down to Boot Override, and select the
UEFI entry for your jumpdrive.

Note: UEFI booting will fail if the SATA cable for
the HDD is plugged in.
The issue is explained under the Flashing instructions.

Flashing:
1. Ensure the MX100 is powered down, and not plugged
into power.
2. Take the top off the MX100, and unplug the SATA
cable from the HDD.
3. Using the Mini USB female port found by the SATA
port on the motherboard,
flash one of the images to the system. Example:
`dd if=image of=/dev/sdb conv=fdatasync` where sdb
is the USB device for the MX100's NAND.
4. Unplug the Mini USB, hook up UART to the MX100,
and then power up the device.
5. At the BIOS prompt, quickly press F7 and then
scroll to the Boot tab.
6. Change the boot order and set UEFI: USB DISK 2.0
as first, and USB DISK 2.0 as second.
Disable the other boot options.
7. Go to Save & Exit, and then select Save Changes and
Reset

Note that OpenWRT will fail to boot in UEFI mode when
the SATA hard drive is plugged in. To fix this, boot
with the SATA disk unplugged and then run the following
command:
`sed -i "s|hd0,gpt1|hd1,gpt1|g" boot/grub/grub.cfg`
Once the above is ran, OpenWRT will boot when the HDD
is plugged into SATA. The reason this happens is the
UEFI implementation for the MX100 will always set
anything on SATA to HD0 instead of the onboard USB
storage, so we have to accomidate it since OpenWRT's
GRUB does not support detecting a boot disk via UUID.

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
2021-10-10 16:47:41 +02:00
Christian Lamparter
e166ee4ff1 apm821xx: disable and move kernel CONFIG_ symbols
try to reduce the kernel size by disabling and moving
options from the common kernel configuration to the
SATA target that doesn't have the constraints.

For NAND this has become necessary because as with 5.10
some devices outgrew their kernels. Though, in my tests
this didn't help much: just a smidgen over 100kib was
saved on the  uncompressed kernel.

... running make kernel_oldconfig also removed some
other config symbols, mostly those that already set
from elsewhere or became obsolete in the meantime.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-10-10 16:47:41 +02:00
Christian Lamparter
44f89614c6 apm821xx: disable MX60(W) due to kernel size
disables the MX60(W) from being built by the builders for now.
But there's an effort to bring it back:
<https://github.com/openwrt/openwrt/pull/4617>

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-10-10 16:47:03 +02:00
Linus Walleij
4293fc32b7 gemini: splash banner on framebuffer console
The D-Link DIR-685 has a small screen with a framebuffer
console, so if we have this, when we start, display the
banner on this framebuffer console so the user know they
are running OpenWRT as root filesystem.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2021-10-10 16:44:15 +02:00
Christian Lamparter
7a6a349445 apm821xx: WNDAP620 + WNDAP660: reorganize partitions for 5.10
Due to 5.10 increased kernel size, the current 4MiB-ish kernel
partition got too small. Luckily, netgear's uboot environment
is setup to read 0x60000 bytes from the kernel partition location.

... While at it: also do some cleanups in the DTS in there.

The original (re-)installation described in
commit d82d84694e ("apm821xx: add support for the Netgear WNDAP620 and WNDAP660")
seemed to be still working for now. What I noticed though
is that the bigger initramfs images needed to use a different
destination address (1000000) to prevent it overwriting
itself during decompression. i.e:
 # tftp 1000000 openwrt-...-wndap620-initramfs-kernel.bin
 # bootm

However, in case of the WNDAP620+660 the factory.img image can be
written directly to the flash through uboot.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-10-10 16:44:15 +02:00
Paul Spooren
4ee9b3f462 apm821xx: switch to Kernel 5.10
Signed-off-by: Paul Spooren <mail@aparcar.org>
2021-10-10 16:44:15 +02:00
Christian Lamparter
2a6cab09b9 apm821xx: move CONFIG_DMA* to the generic apm821xx config
Both NAND and SATA targets need the DMA engine in one way
or another.

Due to a kernel config refresh various existing symbols
got removed from the apm821xx main config file as well.
(That being said, they are still included because the
built-in crpyto4xx depends on these.)

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-10-10 16:44:15 +02:00
John Audia
b5893a4128 kernel: bump 5.4 to 5.4.152
All patches automatically rebased.

Signed-off-by: John Audia <graysky@archlinux.us>
2021-10-10 00:12:55 +01:00
John Audia
416eef7209 kernel: bump 5.4 to 5.4.151
All patches automatically rebased.

Signed-off-by: John Audia <graysky@archlinux.us>
2021-10-10 00:12:10 +01:00
John Audia
e672d1b387 kernel: bump 5.10 to 5.10.72
All patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B
Run-tested: bcm2711/RPi4B

Signed-off-by: John Audia <graysky@archlinux.us>
2021-10-10 00:09:22 +01:00
John Audia
20bc450771 kernel: bump 5.10 to 5.10.71
All patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, ipq806x/R7800
Run-tested: bcm2711/RPi4B, ipq806x/R7800

Signed-off-by: John Audia <graysky@archlinux.us>
2021-10-10 00:09:22 +01:00
Adrian Schmutzler
91eed5d9fb rockchip: rename "Rock Pi 4" to "Rock Pi 4A"
Kernel has added the different variants of the Rock Pi 4 in commit
b5edb0467370 ("arm64: dts: rockchip: Mark rock-pi-4 as rock-pi-4a
dts"). The former Rock Pi 4 is now Rock Pi 4A.

For compatibility with kernel 5.4, this rename has been held back
so far. Having switched to kernel 5.10 now, we can finally apply
it in our tree as well.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-10-10 00:57:56 +02:00
Adrian Schmutzler
0c2aa7c003 rockchip: switch to kernel 5.10
This target has testing support for more than half a year now.
Time to switch.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-10-10 00:51:39 +02:00
Ansuel Smith
5ae2e78639 kernel: drop support for mtd-mac-address
Now that we have fully switched to nvmem interface we can drop
the use of mtd-mac-address patches as it's not used anymore and
the new nvmem implementation should be used for any new device.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2021-10-09 21:14:54 +02:00
Robert Marko
46646efc38 mvebu: mochabin: correct LED labels in DTS
LED labels got reversed by accident, so fix it to the usual color:led_name format.

Fixes: 78cf3e53b1 ("mvebu: add Globalscale MOCHAbin")

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
[add Fixes:]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-10-09 19:27:11 +02:00
Adrian Schmutzler
fb76d543b6 kirkwood: switch to kernel 5.10
This target has testing support for more than half a year now.
Time to switch.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-10-09 18:44:55 +02:00
Daniel Golle
7ab94288e0
oxnas: switch to Linux 5.10
Linux 5.10 has been there as testing kernel for a while now.
Do the switch and drop config and patches for Linux 5.4.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-10-09 16:48:45 +01:00
Daniel Golle
401d7ebf2c
mediatek: enable configfs for DT overlay on mt7622 and mt7623
Enable kernel options to allow loading device tree overlay via configfs
at runtime. This is useful for devboards like the BPi-R2 and BPi-R64
which got RasbPi-compatible 40-pin GPIO header which allow all sorts
of extensions.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-10-09 16:48:34 +01:00
Birger Koblitz
cda0460ad3 realtek: add legacy realtek GPIO driver for rtl9300 support
The otto GPIO driver does not work with rtl9300 SoCs. Add
the legacy driver again and use that by default in the 9300 .dtsi

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:06 +02:00
Birger Koblitz
4c83dae801 realtek: enable Aquantia PHY support
Enables Aquantia PHY support in the kernel

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:06 +02:00
Birger Koblitz
76f60470a1 realtek: Fix bug when accessing external PHYs on SoCs older than Revision C
RTL8393 SoCs older than Revision C hang on accesses to PHYs with PHY address
larger or equal to the CPU-port (52). This will make scanning the MDIO bus
hang forever. Since the RTL8390 platform does not support more than
52 PHYs, return -EIO for phy addresses >= 52. Note that the RTL8390 family
of SoCs has a fixed mapping between port number and PHY-address.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:06 +02:00
Birger Koblitz
88936e7e82 realtek: cleanup PHY driver
Removes unnecessary output from the RTL PHY drivers.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:06 +02:00
Birger Koblitz
1cfd45ae0b realtek: Add debugfs support for RTL9300
Adds support for debugfs on RTL9300, in particular the drop counters.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:06 +02:00
Birger Koblitz
1f402512ae realtek: Add SoC-specific routing offload implementation
Adds SoC specific routing offload implementations for
RTL8380/90 and RTL9300. RTL83xx supports merely nexthop
routing, RTL9300 full host and prefix routes.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:06 +02:00
Birger Koblitz
03e1d93e07 realtek: add driver support for routing offload
Add generic support for listening to FIB and Event notifier updates and
use this information to hook into the L3 hardware capabilities of the
RTL SoCs.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:06 +02:00
Birger Koblitz
35b3c4c212 kernel: Add AQR113C and AQR813 support
This hack adds support for the Aquantia 4th generation, 10GBit
PHYs AQR113C and AQR813.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:06 +02:00
Birger Koblitz
ee6f483a62 realtek: Improve MDIO bus probing for RTL9300
Improve handling of multi-gig ports on the RTL9300 when probing
the MDIO bus.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:06 +02:00
Birger Koblitz
9ae927febd realtek: Fix bug in VLAN ingress and egress filtering
The ingress filter registers use 2 bits for each port to define the filtering
state, whereas the egress filter uses 1 bit. So for for the ingress filter
the register offset for a given port is:
(port >> 4) << 4: since there are 16 entries in a register of 32 bits
and for the egress filter:
(port >> 5) << 4: since there are 32 entries in a register of 32 bits

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:06 +02:00
Birger Koblitz
28e972b2ea realtek: Configure initial L2 learning setup
Configure a sane L2 learning configuration upon DSA driver load so that the
switch can start learning L2 addresses. Also configure the correct flood masks
for broadcast and unknown unicast traffice.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:06 +02:00
Birger Koblitz
9d9bf16aa8 realtek: Add phylink configuration routines for RTL93xx
This adds RTL93xx-specific MAC configuration routines that allow also configuration
of 10GBit links for phylink. There is support for the Realtek-specific HISGMI
protocol.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:06 +02:00
Birger Koblitz
a96b73a890 realtek: Packet Inspection Engine support for RTL930x SoCs
Adds the RTL930x-specific PIE support routines.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:05 +02:00
Birger Koblitz
2d8d81fe28 realtek: Packet Inspection Engine support for RTL839x SoCs
Adds the RTL839x-specific PIE support routines.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:05 +02:00
Birger Koblitz
87b3bd07a4 realtek: Packet Inspection Engine support for RTL838x SoCs
Adds the RTL838x-specific PIE support routines.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:05 +02:00
Birger Koblitz
54805fc911 realtek: Add driver support for TC offloading
This adds support for offloading TC flower by using the Packet Inspection Engine
of the RTL-SoCs. Basic infrastructure support is provide with callbacks to the
tc subsystem and support for HW packet counters.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:05 +02:00
Birger Koblitz
a6678accbd realtek: Add port to smi-bus address mapping
All RTL SoCs addresss PHYs via their port number, which is mapped to an
SMI address. Add support for configuring this mapping via the .dts on all
SoCs apart from the 839x, where the mapping to the 64 ports is fixed.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:05 +02:00
Birger Koblitz
2ab4d40293 realtek: Increase maximum RX ring buffer length
Increase the maximum ring buffer length in order to improve
performance on RTL839x devices.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:05 +02:00
Birger Koblitz
9eab76c84e realtek: Improve TX CPU-Tag usage
On RTL83xx enable learning of the MAC source address of the CPU port
from outgoing packets. Add documentation on bit fields. On RTL93xx
enable port-mask usage and the use of internal priority, these
SoCs automatically learn the MAC.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:05 +02:00
Birger Koblitz
ca04e2dfd0 realtek: Remove storm control and attack warnings
Remove the storm control and attack warnings from the IRQ handler
of the Ethernet driver. There was no consequence to the detection
and the kernel can also handle at least the attacks itself.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:05 +02:00
Birger Koblitz
e88ac0bbd1 realtek: Correct TX ring size in ethernet driver
This enlarges the size of the TX ring buffer, which prevents warnings
when the buffer runs out of space.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:05 +02:00
Paul Spooren
f887c93be7 config: pack toolchain per default on buildbots
The toolchain can be used for accelerated CI builds. This commit enabled
the packing of it by default on buildbots.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2021-10-08 15:06:44 -10:00
Rafał Miłecki
e4e410733f kernel: export switch_generic_set_link() symbol
This fixes:
ERROR: "switch_generic_set_link" [drivers/net/phy/b53/b53_common.ko] undefined!

At some point all packages for swconfig drivers were dropped and targets
were meant to have them built into kernels. It seems b53 (re-)gained its
kmod-switch-bcm53xx however and b53 needs to be built as module.

Fixes: b2cfed48f6 ("Revert "swconfig: fix Broadcom b53 support"")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-10-07 15:13:16 +02:00
Matthew Hagan
2e4193f3cf kernel: 5.10: dsa: don't set skb->offload_fwd_mark when not offloading bridge
Add Vladimir Oltean's "net: dsa: don't set skb->offload_fwd_mark when
not offloading the bridge"

This covers cases where packets received by an upstream switch must be
forwarded back on the same port, which skb->offload_fwd_mark normally
prevents.

Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
2021-10-07 14:22:22 +02:00
Rafał Miłecki
b2cfed48f6 Revert "swconfig: fix Broadcom b53 support"
This reverts commit 8f9cd1af0f.

That commit was meant to add a single EXPORT_SYMBOL_GPL() but it
actually also added few .of_match_table-s. One commit should handle one
thing and should not introduce unrelated changes.

Regarding actual changes:
1. EXPORT_SYMBOL_GPL is not required as we don't build swconfig drivers
   as modules.
2. PHY drivers must not have .of_match_table. That is allowed for MDIO
   drivers. This could work for some time (although is didn't for me on
   bcm53xx) but does not with kernel 5.10. It causes a soft lockup and
   upstream developers confirmed it's an unsupported design.

Link: https://lore.kernel.org/netdev/2b1dc053-8c9a-e3e4-b450-eecdfca3fe16@gmail.com/t/#mf80e472f35ee23f7a75cbf5b1e101a17ab3a64a3
Cc: Tobias Schramm <tobleminer@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-10-07 11:30:55 +02:00
Rafał Miłecki
fd71ef34b7 kernel: backport bgmac upstream commits from 5.15 / for 5.16
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-10-07 11:30:18 +02:00
Adrian Schmutzler
d69bf6601e mpc85xx: switch to Kernel 5.10
This has testing support for 7 months. Time to switch.

TL-WDR4900 is disabled due to kernel size limitation.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-10-05 23:54:48 +02:00
Pawel Dembicki
ce793584e5 kernel: 5.10: add missing symbols
Three missing symbols were found during mpc85xx/p2020 compilation.

While at it, CONFIG_FSL_ENETC_MDIO is moved to generic config
for consistency.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[move CONFIG_FSL_ENETC_MDIO, remove redundant definitions, adjust
commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-10-05 23:54:18 +02:00
Adrian Schmutzler
eb3a99bc18 bcm27xx: remove obsolete kernel 5.4
With the upgrade to kernel 5.10 per default the old version is no
longer required to be in tree.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-10-05 23:54:18 +02:00
Stijn Tintel
57634f472f bcm27xx: add RPI_AXIPERF symbol
When KERNEL_PERF_EVENTS is enabled in OpenWrt, or PERF_EVENTS in the
kernel config, the RPI_AXIPERF is exposed. Add it to the subtarget
kernel configs to avoid build failures.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2021-10-05 23:30:48 +03:00
Stijn Tintel
6f787b62d0 bcm27xx: add SND_SOC_AD193X_{I2C,SPI} symbols
When building an image for the bcm27xx target, some combinations of
config options will fail to build due the SND_SOC_AD193X_I2C and
SND_SOC_AD193X_SPI kernel config symbols being missing.

The problem only occurs on bcm27xx as the target contains a patch that
modifies the Kconfig file containing the symbols; in the vanilla kernel,
there is no string after the tristate keyword so the symbol is not
exposed.

The _I2C symbol depends on I2C, which is enabled in the kernel configs
of all bcm27xx subtargets.

The _SPI symbol depends on SPI_MASTER, which is exposed by either
kmod-mmc-spi, kmod-spi-bitbang, kmod-spi-dev, kmod-spi-bcm2835 or
kmod-spi-bcm2835-aux.

Both symbols are defined in the sound/soc/codecs directory, which is
only included when SND_SOC is enabled, so this problem doesn't occur
when kmod-sound-soc-core is not enabled. As the
kmod-sound-soc-bcm2835-i2s package disables the SND_SOC_AD193X_SPI
symbol, it also doesn't occur when kmod-sound-soc-bcm2835-i2s is
enabled.

As there are several possible config combinations that do exhibit this
problem, it is best to solve it by adding the missing symbols to the
subtarget kernel configs. By doing this we can remove them from the
kmod-sound-soc-bcm2835-i2s package.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2021-10-05 23:30:48 +03:00
David Bauer
f82c93b93c ramips: fix USW-Flex reversed switch-port order
Switch port order was reversed due to reading the internal labling
(which mismatches the one on the case).

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-10-04 23:24:32 +02:00
Hauke Mehrtens
57b323ce38 kernel: Deactivate some ARM64 errata workarounds
This deactivates the following workarounds for erratas in ARM64 CPUS:
CONFIG_ARM64_ERRATUM_1165522: Cortex-A76 cores (r0p0, r1p0, r2p0)
CONFIG_ARM64_ERRATUM_1286807: Cortex-A76 cores (r0p0 to r3p0)
CONFIG_ARM64_ERRATUM_1418040: Cortex-A76/Neoverse-N1 cores (r0p0 to r3p1)
CONFIG_CAVIUM_TX2_ERRATUM_219: Cavium ThunderX2
CONFIG_FUJITSU_ERRATUM_010001: Fujitsu-A64FX

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-10-03 01:13:18 +02:00
Hauke Mehrtens
7d6976bb6b sunxi: Refresh kernel 5.10 configuration
The cortex53 subtarget was missing multiple config options and the other
targets just defined some options which are not needed.

Fixes: 83672f506d ("sunxi: add testing Linux 5.10")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-10-03 01:13:18 +02:00
Hauke Mehrtens
2c6c77bb95 sunxi: Activate CONFIG_SATA_PMP
The kernel 5.4 configuration activated SATA Port Multiplier support, add
it to kernel 5.10 too.

Fixes: 83672f506d ("sunxi: add testing Linux 5.10")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-10-03 01:13:18 +02:00
Sungbo Eo
c7d5c26ab7 kirkwood: refresh kernel config
Refresh config with make kernel_oldconfig.

Tested-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2021-10-03 01:13:18 +02:00
Sungbo Eo
dbfebd14f6 kirkwood: solidify SATA_PMP config
SATA_PMP option is no longer exposed when no SATA host driver is enabled
since upstream linux commit bd322af15ce9 ("ata: make SATA_PMP option
selectable only if any SATA host driver is enabled").

Commit 1bb3f593ee ("kirkwood: update config for kernel 5.10") manually
added CONFIG_SATA_PMP=y to config file, but the config will disappear for
every kernel_oldconfig refresh.

To prevent this, a small hack is added, which selects SATA_HOST
automatically when SATA_PMP is enabled. This patch can be dropped if
SATA_MV is ever re-added into kernel config file.

Tested-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[Move patch to generic/hack-5.10]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-10-03 01:13:12 +02:00
Adrian Schmutzler
2d977eb3d5 ath79: add recipe for common setup with loader-okli-compile
These instructions are repeated for a few devices now, let's move
them to shared definition so we do not repeat ourselves too often.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-10-02 21:26:12 +02:00
Paul Fertser
3810e89729 realtek: ensure output drivers are enabled in RTL8231
The bootloader can leave the GPIO expander in a state which doesn't have
output drivers enabled so GPIOs will properly work for input but output
operations will have no effect.

To avoid disrupting the boot in case the bootloader left direction and
data registers in an inconsistent state (e.g. pulling SoC's reset to 0)
reconfigure everything as input.

Reviewed-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
2021-10-02 21:26:12 +02:00
Paul Spooren
8ff8323335 mvebu: remove obsolete Kernel 5.4
With the upgrade to Kernel 5.10 per default the old version is no longer
required to be in tree.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2021-10-02 18:16:33 +02:00
Paul Spooren
b48d30521d ipq806x: remove obsolete Kernel 5.4
With the upgrade to Kernel 5.10 per default the old version is no longer
required to be in tree.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2021-10-02 18:15:23 +02:00
Paul Spooren
cac2ca1d43 gemini: remove obsolete Kernel 5.4
With the upgrade to Kernel 5.10 per default the old version is no longer
required to be in tree.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2021-10-02 18:14:42 +02:00
Paul Spooren
b6645b7f38 malta: remove obsolete Kernel 5.4
With the upgrade to Kernel 5.10 per default the old version is no longer
required to be in tree.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2021-10-02 18:13:46 +02:00
Paul Spooren
e439613f1f armvirt: remove obsolete Kernel 5.4
With the upgrade to Kernel 5.10 per default the old version is no longer
required to be in tree.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2021-10-02 18:13:46 +02:00
Paul Spooren
eea90d2dff x86: remove obsolete Kernel 5.4
With the upgrade to Kernel 5.10 per default the old version is no longer
required to be in tree.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2021-10-02 18:13:46 +02:00
Hauke Mehrtens
50f456b46c kernel: bump 5.4 to 5.4.150
Manually rebased:
  generic/pending-5.4/800-bcma-get-SoC-device-struct-copy-its-DMA-params-to-th.patch
  mvebu/patches-5.4/021-arm64-dts-marvell-armada-37xx-Move-PCIe-comphy-handl.patch

Removed upstreamed:
  layerscape/patches-5.4/819-uart-0004-MLK-18137-fsl_lpuart-Fix-loopback-mode.patch

All others updated automatically.

Compile-tested on: lantiq/xrx200, armvirt/64
Runtime-tested on: lantiq/xrx200, armvirt/64

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-10-02 16:45:56 +02:00
Robert Marko
78cf3e53b1 mvebu: add Globalscale MOCHAbin
Globalscale MOCHAbin is a Armada 7040 based development board.

Specifications:
* Armada 7040 Quad core ARMv8 Cortex A-72 @ 1.4GHz
* 2 / 4 / 8 GB of DDR4 DRAM
* 16 GB eMMC
* 4MB SPI-NOR (Bootloader)
* 1x M.2-2280 B-key socket (for SSD expansion, SATA3 only)
* 1x M.2-2250 B-key socket (for modems, USB2.0 and I2C only)
* 1x Mini-PCIe 3.0 (x1, USB2.0 and I2C)
* 1x SATA 7+15 socket (SATA3)
* 1x 16-pin (2×8) MikroBus Connector
* 1x SIM card slot (Connected to the mini-PCIe and both M.2 slots)
* 2x USB3.0 Type-A ports via SMSC USB5434B hub
* Cortex 2x5 JTAG
* microUSB port for UART (PL2303GL/PL2303SA onboard)
* 1x 10G SFP+
* 1x 1G SFP (Connected to 88E1512 PHY)
* 1x 1G RJ45 with PoE PD (Connected to 88E1512 PHY)
* 4x 1G RJ45 ports via Topaz 88E6141 switch
* RTC with battery holder (SoC provided, requires CR2032 battery)
* 1x 12V DC IN
* 1x Power switch
* 1x 12V fan header (3-pin, power only)
* 1x mini-PCIe LED header (2x0.1" pins)
* 1x M.2-2280 LED header (2x0.1" pins)
* 6x Bootstrap jumpers
* 1x Power LED (Green)
* 3x Tri-color RGB LEDs (Controllable)
* 1x Microchip ATECC608B secure element

Note that 1G SFP and 1G WAN cannot be used at the same time as they are in
parallel connected to the same PHY.

Installation:

Copy dtb from build_dir to bin/ and run tftpserver there:
$ cp ./build_dir/target-aarch64_cortex-a72_musl/linux-mvebu_cortexa72/image-armada-7040-mochabin.dtb bin/targets/mvebu/cortexa72/
$ in.tftpd -L -s bin/targets/mvebu/cortexa72/

Connect to the device UART via microUSB port and power on the device.

Power on the device and hit any key to stop the autoboot.

Set serverip (host IP) and ipaddr (any free IP address on the same subnet), e.g:
$ setenv serverip 192.168.1.10 # Host
$ setenv ipaddr 192.168.1.15 # Device

Set the ethernet device (Example for the 1G WAN):
$ setenv ethact mvpp2-2

Ping server to confirm network is working:
$ ping $serverip
Using mvpp2-2 device
host 192.168.1.15 is alive

Tftpboot the firmware:
$ tftpboot $kernel_addr_r openwrt-mvebu-cortexa72-globalscale_mochabin-initramfs-kernel.bin
$ tftpboot $fdt_addr_r image-armada-7040-mochabin.dtb

Boot the image:
$ booti $kernel_addr_r - $fdt_addr_r

Once the initramfs is booted, transfer openwrt-mvebu-cortexa72-globalscale_mochabin-squashfs-sdcard.img.gz
to /tmp dir on the device.

Gunzip and dd the image:
$ gunzip /tmp/openwrt-mvebu-cortexa72-globalscale_mochabin-squashfs-sdcard.img.gz
$ dd if=/tmp/openwrt-mvebu-cortexa72-globalscale_mochabin-squashfs-sdcard.img of=/dev/mmcblk0 && sync

Reboot the device.

Hit any key to stop the autoboot.

Reset U-boot env and set the bootcmd:
$ env default -a
$ setenv bootcmd 'load mmc 0 ${loadaddr} boot.scr && source ${loadaddr}'

Optionally I would advise to edit the console env variable to remove earlycon as that
causes the kernel to never use the driver for the serial console.
Earlycon should be used only for debugging before the kernel can configure the console
and will otherwise cause various issues with the console.

$ setenv console 'console=ttyS0,115200'

Save and reset
$ saveenv
$ reset

OpenWrt should boot from eMMC now.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2021-10-02 16:45:35 +02:00
Daniel Kestrel
ca1874437c lantiq: kernel: xway-nand: Move ECC engine setting to new DT binding
When trying to add support for another device with Micron NAND chips,
it was discovered that the default setting in the kernel source does
not work with Micron Chips, since the device trees setting is
overwritten and hard coded by the kernel xway_nand driver. This was
the original reason for this PR.
A kernel patch sets the default ECC mode to soft without overwriting
the device tree settings and the device tree for devices using it
are updated with new parameters because the old ones are deprecated
by torvalds/linux@533af69.
A patch for kernel 5.4 is provided to support the new settings
because kernel 5.4 does not support it.

Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
2021-10-02 16:45:33 +02:00
Hauke Mehrtens
6bb51c9d1c lantiq: kernel: xway-nand: Fix setting on-die ECC engines in dts
This backports a fix proposed for upstream kernel to fix overwriting
the NAND ECC engine in device tree.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-10-02 16:45:33 +02:00
Daniel Golle
21c7a8593d
mediatek: mt7623: bpi-r2: add LED aliases
Add aliases for LEDs in device tree of the BPi-R2.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-10-01 23:29:02 +01:00
Daniel Golle
6b434d3c44
mediatek: remove files and patches for Linux 5.4
All subtargets only provide files and patches for Linux 5.10 by now
so there is little use for the old Linux 5.4 stuff. Remove it.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-10-01 23:28:24 +01:00
Paul Spooren
87623958b2 armvirt: switch to Kernel 5.10
Armvirt is a development and testing platform and should therefore use
the latest OpenWrt Kernel by default.

Tested via qemu.

Acked-by: Rosen Penev <rosenp@gmail.com>
Acked-by: Yousong Zhou <yszhou4tech@gmail.com>

Signed-off-by: Paul Spooren <mail@aparcar.org>
2021-10-01 10:46:28 -10:00
Paul Spooren
05b20d9a60 malta: switch to Kernel 5.10
Malta is a development and testing platform and should therefore use the
latest OpenWrt Kernel by default.

Acked-by: Rosen Penev <rosenp@gmail.com>
Acked-by: Yousong Zhou <yszhou4tech@gmail.com>

Signed-off-by: Paul Spooren <mail@aparcar.org>
2021-10-01 10:36:24 -10:00
Daniel Golle
b34a349f07 mediatek: add FEATURES and order them alphabetically
Add common features 'gpio', 'nand', 'pci', 'pcie', 'squashfs' and 'usb'
for all mediatek targets, add 'display' and 'usbgadget' for MT7623.
Sort features alphabetically while at it.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-09-30 22:52:12 +01:00
Daniel Golle
0d9aae10e4 mediatek: mt7622: provide power on mPCIe in SATA mode
User reported that R64 doesn't provide power to the mPCIe slot in case
the PCIe port is disabled as it is when selecting the SATA
configuration. As users may still want to use USB-connected mPCIe
modules in CN8 slot.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-09-30 22:48:39 +01:00
Rui Salvaterra
b4cee3b63f kernel: bump 5.10 to 5.10.70
Deleted (upstreamed):
bcm53xx/patches-5.10/181-Revert-USB-bcma-Add-a-check-for-devm_gpiod_get.patch

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-09-30 22:29:33 +01:00
Rui Salvaterra
2bf320a5e5 kernel: bump 5.10 to 5.10.69
Patches automatically refreshed.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-09-30 22:29:33 +01:00
Rui Salvaterra
9664b41c05 kernel: bump 5.10 to 5.10.68
Deleted (upstreamed):
generic/backport-5.10/610-v5.13-02-netfilter-Fix-fall-through-warnings-for-Clang.patch
generic/backport-5.10/792-v5.15-0001-net-dsa-b53-Fix-calculating-number-of-switch-ports.patch
generic/backport-5.10/792-v5.15-0002-net-dsa-b53-Set-correct-number-of-ports-in-the-DSA-s.patch
generic/backport-5.10/792-v5.15-0003-net-dsa-b53-Fix-IMP-port-setup-on-BCM5301x.patch
generic/backport-5.10/840-0001-PCI-of-Don-t-fail-devm_pci_alloc_host_bridge-on-miss.patch
generic/backport-5.10/840-0002-PCI-iproc-Fix-BCMA-probe-resource-handling.patch
generic/pending-5.10/498-mtd-mtdconcat-select-readwrite-function.patch

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-09-30 22:29:33 +01:00
Rui Salvaterra
6e7fadb0c7 kernel: bump 5.10 to 5.10.67
Deleted (upstreamed):
bcm27xx/patches-5.10/950-0312-vc4_hdmi-Set-HD_CTL_WHOLSMP-and-HD_CTL_CHALIGN_SET.patch

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-09-30 22:29:33 +01:00
Rui Salvaterra
3a2c16d1d2 kernel: bump 5.10 to 5.10.65
Manually refreshed:
generic/pending-5.10/800-bcma-get-SoC-device-struct-copy-its-DMA-params-to-th.patch
bcm27xx/patches-5.10/950-0053-firmware-bcm2835-Support-ARCH_BCM270x.patch
bcm27xx/patches-5.10/950-0087-firmware-raspberrypi-Add-backward-compatible-get_thr.patch

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-09-30 22:29:33 +01:00
Dale Hui
830c2e5378 ramips: add support for Netgear R7450
Netgear R7450 is a clone of Netgear R6700v2

Specifications
==============
SoC: MediaTek MT7621AT
RAM: 256M DDR3
FLASH: 128M NAND
WiFi: MediaTek MT7615N an+ac
MediaTek MT7615N bgn
ETH: MediaTek MT7621AT
BTN: 1x Connect (WPS), 1x WLAN, 1x Reset
LED: Power (white/amber), WAN(white/amber), 2.4G(white), 5G(white),
USB(white) , GuestWifi(white) 4x LAN(white/amber), Wifi Button(white),
WPS Button(white)

Flash Instructions
==================
Login to netgear webinterface and flash factory.img

Signed-off-by: Dale Hui <strokes-races0b@icloud.com>
[fix model/compatible in DTS]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-09-26 15:38:01 +02:00
Dale Hui
16fc409e7a ramips: add support for Netgear R6900v2
Netgear R6900v2 is a clone of Netgear R6700v2

Specifications
==============
SoC: MediaTek MT7621AT
RAM: 256M DDR3
FLASH: 128M NAND
WiFi: MediaTek MT7615N an+ac
MediaTek MT7615N bgn
ETH: MediaTek MT7621AT
BTN: 1x Connect (WPS), 1x WLAN, 1x Reset
LED: Power (white/amber), WAN(white/amber), 2.4G(white), 5G(white),
USB(white) , GuestWifi(white) 4x LAN(white/amber), Wifi Button(white),
WPS Button(white)

Flash Instructions
==================
Login to netgear webinterface and flash factory.img

Signed-off-by: Dale Hui <strokes-races0b@icloud.com>
2021-09-26 15:15:36 +02:00
Dale Hui
95807f89ff ramips: add Nighthawk AC2100 as name for Netgear R6700v2
Netgear Nighthawk AC2100 is another name of the Netgear R6700v2.

Signed-off-by: Dale Hui <strokes-races0b@icloud.com>
[adjust commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-09-26 15:15:36 +02:00
Dale Hui
af3104d25b ramips: make Netgear R7200 a separate device from R6700v2
With the various variants of Netgear R**** devices, make it more
obvious which image should be used for the R7200.

Signed-off-by: Dale Hui <strokes-races0b@icloud.com>
[provide proper commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-09-26 15:15:30 +02:00
INAGAKI Hiroshi
fc050c7b53 realtek: add Kernel 5.10 as testing version
This patch adds "KERNEL_TESTING_PATCHVER:=5.10" to the Makefile in
realtek target to allow using Kernel 5.10 for testing.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-26 00:32:18 +02:00
INAGAKI Hiroshi
216011e424 realtek: enable uart1 on the devices with PoE support in 5.10
On the devices with PoE support, the secondary UART (uart1) on the SoC
is used to communicate between the SoC and controller.

Enable the secondary UART on the following devices:

- D-Link DGS-1210-10P
- Netgear GS110TPP v1
- Netgear GS310TP v1
- ZyXEL GS1900-8HP v1/v2
- ZyXEL GS1900-10HP
- ZyXEL GS1900-24HP v2

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-26 00:32:18 +02:00
INAGAKI Hiroshi
45b2a5d840 realtek: use physical addresses in soc dtsi in 5.10
Use physical addresses instead of virtual address in dts files.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-26 00:32:18 +02:00
INAGAKI Hiroshi
d7b349db7c realtek: use gpio-keys instead of "-polled" if SoC GPIO is used in 5.10
The new backported GPIO driver supports interrupt, so use gpio-keys
instead of gpio-keys-polled for keys connected to the internal GPIO
controller.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-26 00:32:18 +02:00
INAGAKI Hiroshi
61a3d0075b realtek: update GPIO bindings in the dts files in dts-5.10
this patch includes the following changes:

- adjust mapping for the new driver
  - GPIO 24 -> GPIO 0
  - GPIO 47 -> GPIO 0 (+ disabling system LED)

- disable pins in the invalid range
  (out of the range 0-31 of the new driver)
  - are these pins on the external RTL8231 (&gpio1)?
    - GPIO 67 (-> GPIO 3 on &gpio1?)
    - GPIO 94 (-> GPIO 30 on &gpio1?)

- drop "indirect-access-bus-id" property from gpio0 node in device dts
  files

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-26 00:32:18 +02:00
INAGAKI Hiroshi
2e676c05dc realtek: fix kernel panic in DSA driver for 5.10
dsa_to_port function in 5.10 returns dsa_port from the port list in
dsa_switch_tree, but the tree is built when the switch is registered
by dsa_register_switch and it's null in rtl83xx_mdio_probe.

So, we need to use dsa_to_port after the registration of the switch.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-26 00:32:18 +02:00
INAGAKI Hiroshi
99a658cb71 realtek: add pinmux node of LED_GLB_CTRL to rtl838x.dtsi in dts-5.10
This patch adds a pinctrl-single pinmux node to allow disabling system
LED and enabling GPIO 0 (old driver: GPIO 24).

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-26 00:32:18 +02:00
INAGAKI Hiroshi
a22602728c realtek: fix compile errors in dsa driver for 5.10
this patch fixes the following errors when compiling:

- dsa_switch_alloc is removed[1]

- a parameter "enum dsa_tag_protocol mprot" is added to dsa_tag_protocol
  in dsa_switch_ops (include/net/dsa.h)

- several paramters are added to "phylink_mac_link_up" in dsa_switch_ops
  (include/net/dsa.h)

  added:
    - int speed
    - int duplex
    - bool tx_pause
    - bool rx_pause

- a parameter "struct switchdev_trans *trans" is added to
  port_vlan_filtering in dsa_switch_ops (include/net/dsa.h)

[1]: https://lore.kernel.org/lkml/20191020031941.3805884-17-vivien.didelot@gmail.com/

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-26 00:32:18 +02:00
INAGAKI Hiroshi
9a4b8d6c30 realtek: fix compile errors in rtl838x_eth.c for 5.10
this patch fixes the following errors when compiling:

- "unsigned int txqueue" is added as an additional parameter of
  ndo_tx_timeout in net_device_ops (include/linux/netdevice.h)

- "mac_link_state" in phylink_mac_ops (include/linux/phylink.h)
  is renamed to "mac_pcs_get_state" and changed the return value
  to void from int

- several parameters are added to "mac_link_up" in phylink_mac_ops
  (include/linux/phylink.h) and the order of the parameters is
  changed

  added:
    - int speed
    - int duplex
    - bool tx_pause
    - bool rx_pause

- a parameter "phy_interface_t *interface" is added to of_get_phy_mode
  (drivers/of/of_net.c) and returns the state instead of phy mode

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-26 00:32:18 +02:00
INAGAKI Hiroshi
3069fffe60 realtek: add "soc" node to soc dtsi in dts-5.10
Add a "soc" node as a simple-bus to rtl838x.dtsi and rtl930x.dtsi.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-26 00:32:17 +02:00
INAGAKI Hiroshi
ddaeb73de0 realtek: update soc dtsi in 5.10 for backported drivers
this patch updates SoC dtsi (rtl838x.dtsi, rtl930x.dtsi) for the
following backported drivers:

- gpio-realtek-otto (5.13)
- spi-realtek-rtl (5.12)
- irq-realtek-rtl (5.12)

And, disable SoC GPIO node (gpio0) in rtl930x.dtsi in dts-5.10.
Currently, the upstreamed driver doesn't support the GPIO controller on
RTL930x SoC.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-26 00:32:17 +02:00
INAGAKI Hiroshi
1c020f8b43 realtek: cleanup and update soc dtsi in 5.10
the following changes are included in this patch:

- node is enabled by default, drop 'status = "okay"'
- adjust order of "compatible" lines and "reg" lines
- add a new blank line before fixed-link node in rtl830x.dtsi

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-26 00:32:17 +02:00
INAGAKI Hiroshi
0de230bd0c realtek: copy dts directory for Kernel 5.10
This patch adds "dts-5.10" directory to use backported drivers.
There are several specification changes in the new drivers, so there
are some compatibility issues in using dts/dtsi files for 5.4.

The old DTS files are moved to "dts-5.4", so their corresponding
kernel version is obvious as well.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[change "dts" to "dts-5.4", adjust Makefile]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-09-26 00:32:17 +02:00
INAGAKI Hiroshi
9e418b061c realtek: refresh and update config-5.10
This patch adjusts config-5.10 by running kernel_menuconfig.

Note:

- disable psb6970 phy driver (unused in realtek target?)

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-26 00:32:17 +02:00
INAGAKI Hiroshi
95f089dafe realtek: refresh patches for Kernel 5.10
This patch refresh all patches in patches-5.10/ to adjust for Kernel
5.10.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-26 00:32:17 +02:00
INAGAKI Hiroshi
46945e02d3 realtek: remove unnecessary line from rtl838x/Platform in 5.10
The following line is already defined in arch/mips/Kbuild.platforms by
300-mips-add-rtl838x-platform.patch.

platform-$(CONFIG_RTL838X) += rtl838x/

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-26 00:32:17 +02:00
INAGAKI Hiroshi
781f50705c realtek: drop fixup_bigphys_addr from ioremap.h in 5.10
A macro with the same name is provided in asm/pgtable.h in Kernel 5.10,
use it and drop from ioremap.h.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-26 00:32:17 +02:00
INAGAKI Hiroshi
2ec38bfea1 realtek: fix "help" line in Kconfig in files/patches for 5.10
In Kernel 5.10, "help" must be used instead of "---help---".

this patch fixes the following errors:

drivers/net/dsa/rtl83xx/Kconfig:7: syntax errorgit
drivers/net/dsa/rtl83xx/Kconfig:6: unknown statement "---help---"
drivers/net/dsa/rtl83xx/Kconfig:7:warning: ignoring unsupported character '.'
drivers/net/dsa/rtl83xx/Kconfig:7: unknown statement "This"
drivers/net/ethernet/Kconfig:170: syntax error
drivers/net/ethernet/Kconfig:169: unknown statement "---help---"
drivers/net/ethernet/Kconfig:170:warning: ignoring unsupported character '.'
drivers/net/ethernet/Kconfig:170: unknown statement "Say"
drivers/net/phy/Kconfig:331: syntax error
drivers/net/phy/Kconfig:330: unknown statement "---help---"
drivers/net/phy/Kconfig:331: unknown statement "Supports"

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-26 00:32:17 +02:00
INAGAKI Hiroshi
2cd00b5147 realtek: backport irq-realtek-rtl driver from 5.12 to 5.10
This patch backports "irq-realtek-rtl" driver to Kernel 5.10 from 5.12.
"MACH_REALTEK_RTL" is used as a platform name in upstream, but "RTL838X"
is used in OpenWrt, so update the dependency by the additional patch.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-26 00:32:17 +02:00
INAGAKI Hiroshi
b2bd0199a8 realtek: drop platform irq driver from 5.10
To use backported irq driver, drop old irq driver from realtek target
and call irqchip_init() in setup.c.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-26 00:32:17 +02:00
INAGAKI Hiroshi
9bac1c20b8 realtek: backport gpio-realtek-otto driver from 5.13 to 5.10
This patch backports "gpio-realtek-otto" driver to Kernel 5.10.
"MACH_REALTEK_RTL" is used as a platform name in upstream, but "RTL838X"
is used in OpenWrt, so update the dependency by the additional patch.

Note: GPIO mapping is changed in the upstreamed driver.

  old - new

   24 -  0
   25 -  1
   26 -  2
   27 -  3
   28 -  4
   29 -  5
   30 -  6
   31 -  7
   16 -  8
   17 -  9
   18 - 10
   19 - 11
   20 - 12
   21 - 13
   22 - 14
   23 - 15
    8 - 16
    9 - 17
   10 - 18
   11 - 19
   12 - 20
   13 - 21
   14 - 22
   15 - 23

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-26 00:32:17 +02:00
INAGAKI Hiroshi
fbd675c668 realtek: drop rtl838x gpio driver from 5.10
To backport the upstreamed driver (gpio-realtek-otto) from 5.13, drop the
old driver from realtek target.

And, modify 301-gpio-add-rtl838x-driver.patch to remove rtl838x GPIO
support and rename it only for rtl8231 GPIO support.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-26 00:32:17 +02:00
INAGAKI Hiroshi
0b000cbfe0 realtek: backport spi-realtek-rtl driver from 5.12 to 5.10
This patch backports "spi-realtek-rtl" driver to Kernel 5.10 from 5.12.
"MACH_REALTEK_RTL" is used as a platform name in upstream, but "RTL838X"
is used in OpenWrt, so update the dependency by the additional patch.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-26 00:32:17 +02:00
INAGAKI Hiroshi
1651bd9bc6 realtek: drop rtl838x spi-nor driver from 5.10
To backport the upstreamed driver (spi-realtek-rtl) from 5.12, drop the
old driver from realtek target.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-26 00:32:17 +02:00
INAGAKI Hiroshi
95170b4350 realtek: copy config/files/patches to 5.10
this patch copies the following files from 5.4 to 5.10:

- config-5.4   -> config-5.10
- files-5.4/   -> files-5.10/
- patches-5.4/ -> patches-5.10/

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[rebase on change in files-5.4]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-09-26 00:32:17 +02:00
David Bauer
1edc7078d6 ramips: enable I2C_CHARDEV
Expose I2C busses with a chardev device. This is required to control the
PSE controller on the Ubiquiti UniFi Flex Switch.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-09-25 21:05:07 +02:00
David Bauer
a983969789 ramips: add support for Ubiquiti USW-Flex
Hardware
--------
MediaTek MT7621AT
16M SPI-NOR Macronix MX25L12835FMI
Microchip PD69104B1 4-Channel PoE-PSE controller
TI TPS2373 PoE-PD controller

PoE-Controller
--------------

By default, the PoE outputs do not work with OpenWrt. To make them output
power, install the "poemgr" package from the packages feed.
This package can control the PD69104B1 PSE controller.

Installation
------------

1. Connect to the booted device at 192.168.1.20 using username/password
   "ubnt" via SSH.

2. Add the uboot-envtools configuration file /etc/fw_env.config with the
   following content

   $ echo "/dev/mtd1 0x0 0x1000 0x10000 1" > /etc/fw_env.config

3. Update the bootloader environment.

   $ fw_setenv boot_openwrt "fdt addr \$(fdtcontroladdr);
     fdt rm /signature; bootubnt"
   $ fw_setenv bootcmd "run boot_openwrt"

4. Transfer the OpenWrt sysupgrade image to the device using SCP.

5. Check the mtd partition number for bs / kernel0 / kernel1

   $ cat /proc/mtd

6. Set the bootselect flag to boot from kernel0

   $ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock4

7. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1

   $ dd if=openwrt.bin of=/dev/mtdblock6
   $ dd if=openwrt.bin of=/dev/mtdblock7

8. Reboot the device. It should boot into OpenWrt.

Restore to UniFi
----------------

To restore the vendor firmware, follow the Ubiquiti UniFi TFTP
recovery guide for access points. The process is the same for
the Flex switch.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-09-25 21:04:53 +02:00
Andrew Cameron
ac03e24635 ath79: add support for TP-Link CPE710-v1
TP-Link CPE710-v1 is an outdoor wireless CPE for 5 GHz with
one Ethernet port based on the AP152 reference board

Specifications:
- SoC: QCA9563-AL3A MIPS 74kc @ 775MHz, AHB @ 258MHz
- RAM: 128MiB DDR2 @ 650MHz
- Flash: 16MiB SPI NOR Based on the GD25Q128
- Wi-Fi 5Ghz: ath10k chip (802.11ac for up to 867Mbps on 5GHz wireless
  data rate) Based on the QCA9896
- Ethernet: one 1GbE port
- 23dBi high-gain directional 2×2 MIMO antenna and a dedicated metal
  reflector
- Power, LAN, WLAN5G Blue LEDs
- 3x Blue LEDs

Flashing instructions:
Flash factory image through stock firmware WEB UI or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 30-40 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP address:192.168.0.254

Signed-off-by: Andrew Cameron <apcameron@softhome.net>
[convert to nvmem, fix MAC assignment in 11-ath10k-caldata]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-09-25 19:28:54 +02:00
Robert Marko
3c3b84fd87 kernel: 5.10: backport fix for lp55xx LED driver
This backports the upstream commit:
leds: lp55xx: Initialize enable GPIO direction to output

Without it under kernel 5.10 on Asus MAP-AC2200
the LED driver will fail probing:
[    1.947521] lp5523x: probe of 0-0032 failed with error -22

After the backported fix:
[    1.873236] lp5523x 0-0032: lp5523 Programmable led chip found

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Tested-by: Szabolcs Hubai <szab.hu@gmail.com> [ipq4029/gl-b1300]
Tested-by: Nick Hainke <vincent@systemli.org> [ipq4019/fritzbox-7530
                                               ipq4019/fritzbox-4040
                                               ipq4019/sxtsq-5ac]
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ipq4019/map-ac2200]
2021-09-25 19:28:54 +02:00
Robert Marko
7b1fa276f5 ipq40xx: add testing support for kernel 5.10
Add kernel 5.10 as the testing kernel to ipq40xx to
get wider testing.

The following devices failed to build with buildbot settings and all
feeds installed (apparently due to kernel size):

 * cell-c rtl30vw
 * compex wpj428
 * devolo magic 2 next
 * engenius emr3500
 * glinet gl-b1300
 * glinet gl-s1300
 * qcom ap-dk01.1-c1
 * qcom ap-dk04.1-c1

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Tested-by: Nick Hainke <vincent@systemli.org> [ipq4019/fritzbox-7530
                                               ipq4019/fritzbox-4040
                                               ipq4019/sxtsq-5ac]
Tested-by: Szabolcs Hubai <szab.hu@gmail.com> [ipq4029/gl-b1300]
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ipq4019/map-ac2200]
[add tested-by and note about failed devices]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-09-25 19:28:54 +02:00
Robert Marko
f4fb63d2ab ipq40xx: 5.10: move AR40xx to MDIO drivers
MDIO drivers were moved into their own sub directory of networking drivers.
This has caused the AR40xx driver to probe before MDIO drivers and that wont
work as it depends on the MDIO bus to be up so it can be fetched.

Lets solve it by moving the AR40xx into MDIO folder so they get probed like
before.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2021-09-25 19:28:54 +02:00
Robert Marko
ccf214a408 ipq40xx: net: ethernet: edma: reject unsupported coalescing params
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.

This driver did not previously reject unsupported parameters.

This is a required ethtool op since kernel 5.7.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2021-09-25 19:28:54 +02:00
Robert Marko
603848cad8 ipq40xx: net: ethernet: edma: update of_get_phy_mode() for 5.10
In kernel v5.5 of_get_phy_mode had its API changed, so its now returning 0
or errors instead of phymode.

Phymode is now returning by passing a pointer to phy_interface_t where it
will be stored.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2021-09-25 19:28:54 +02:00
Robert Marko
80f007fdb2 ipq40xx: 5.10: add kernel config
Copy config from 5.4 and run "make kernel_oldconfig".

Select default ("N") for all new symbols.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
[make commit message more explicit]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-09-25 19:28:54 +02:00
Robert Marko
e9559182b9 ipq40xx: 5.10: refresh patches to apply
Refresh the kernel patches on top of 5.10 so they apply.
Manually fixup the 705-net-add-qualcomm-ar40xx-phy.patch
to apply.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2021-09-25 19:28:54 +02:00
Robert Marko
fec22cfa59 ipq40xx: 5.10: replace patches with upstreamed versions
USB and SDHCI LDO DTS patches have been upstreamed into 5.12, so
replace the local versions with upstreamed ones.

Reorder, and clearly mark the kernel version.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2021-09-25 19:28:54 +02:00
Robert Marko
75a90f161e ipq40xx: 5.10: remove duplicate GPIO export patch
Its in the generic target already, so remove the duplicate
as it breaks compilation.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2021-09-25 19:28:54 +02:00
Robert Marko
9fe5516ee5 ipq40xx: 5.10: drop upstreamed patches
Drop patches that have been upstreamed in before 5.10.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2021-09-25 19:28:54 +02:00
Robert Marko
8f27ac5ec0 ipq40xx: 5.10: copy patches
Copy over the 5.4 kernel patches to 5.10 folder.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2021-09-25 19:28:54 +02:00
INAGAKI Hiroshi
7ff0efa0b0 ramips: add support for I-O DATA WN-DX2033GR
I-O DATA WN-DX2033GR is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on
MT7621A.

Specification:

- SoC		: MediaTek MT7621A
- RAM		: DDR3 128 MiB
- Flash		: Raw NAND 128 MiB (Macronix MX30LF1G18AC-TI)
- WLAN		: 2.4/5 GHz
  - 2.4 GHz	: 2T2R, MediaTek MT7603E
  - 5 GHz	: 4T4R, MediaTek MT7615
- Ethernet	: 5x 10/100/1000 Mbps
  - Switch	: MediaTek MT7530 (SoC)
- LEDs/Keys	: 2x/3x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - J5: 3.3V, TX, RX, NC, GND from triangle mark
  - 57600n8
- Power		: 12 VDC, 1 A

Flash instruction using initramfs image:

1. Boot WN-DX2033GR normally
2. Access to "http://192.168.0.1/" and open firmware update page
   ("ファームウェア")
3. Select the OpenWrt initramfs image and click update ("更新") button
   to perform firmware update
4. On the initramfs image, download the sysupgrade.bin image to the
   device and perform sysupgrade with it
5. Wait ~120 seconds to complete flashing

Notes:

- The hardware of WN-DX2033GR and WN-AX2033GR are almost the same, and
  it is certified under the same radio-wave related regulations in Japan

- The last 0x80000 (512 KiB) in NAND flash is not used on stock firmware

- stock firmware requires "customized uImage header" (called as "combo
  image") by MSTC (MitraStar Technology Corp.), but U-Boot doesn't

  - uImage magic ( 0x0 - 0x3 ) : 0x434F4D42 ("COMB")
  - header crc32 ( 0x4 - 0x7 ) : with "data length" and "data crc32"
  - image name   (0x20 - 0x37) : model ID and firmware versions
  - data length  (0x38 - 0x3b) : kernel + rootfs
  - data crc32   (0x3c - 0x3f) : kernel + rootfs

- There are 2x important flags in the flash:

  - bootnum   : select os partition for booting (persist, 0x4)

    - 0x01: firmware
    - 0x02: firmware_2

  - debugflag : allow interrupt kernel loader, it's named as "Z-LOADER"
    (Factory, 0xFE75)

    - 0x00: disable debug
    - 0x01: enable debug

MAC addresses:

LAN     : 50:41:B9:xx:xx:90 (Factory, 0xE000 (hex) / Ubootenv, ethaddr (text))
WAN     : 50:41:B9:xx:xx:92 (Factory, 0xE006 (hex))
2.4 GHz : 50:41:B9:xx:xx:90 (Factory, 0x4    (hex))
5 GHz   : 50:41:B9:xx:xx:91 (Factory, 0x8004 (hex))

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-25 19:28:54 +02:00
Paul Fertser
16ae56b4f9 realtek: fix RTL8231 gpio expander for high GPIOs
GPIOs > 31 require special handling. This patch fixes both the
initialisation and direction get/set operations.

Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Sander Vanheule <sander@svanheule.net>
2021-09-25 19:28:54 +02:00
Felix Fietkau
8ea0d08e0e kernel: add patch to fix an issue with kernel headers that broke perf
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-09-25 14:08:48 +02:00
Alan Luck
2c9a07ed28 ramips: add missing information to dlink headers
Add additional header information required for newer
bootloaders found on DIR-2660-A1 & A2.

Also remove the MTD splitter compatible from the second firmware
partition, as OpenWrt only supports handling of the first one.

Signed-off-by: Alan Luck <luckyhome2008@gmail.com>
[rephrase commit message, remove removal of read-only flags]
Signed-off-by: David Bauer <mail@david-bauer.net>
2021-09-24 12:32:28 +02:00
David Bauer
b56f7407d9 rockchip: fix broken squashfs sysupgrade
The rockchip platform supports squashfs SD card images. However, the
resulting image is not padded to completely fill the rootfs partition.

Because of that, the f2fs overlay might not be erased, resulting in
uci-defaults not bing executed or the configuration not being erased,
even though drop config was selected.

Modify the image generation process so the image is padded to cover the
entire root filesystem partition.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-09-24 12:28:48 +02:00
Moritz Warning
b34aa6aff7 bcm47xx: use device vendor/model variable
Remove use of DEVICE_TITLE in favor of the
DEVICE_VENDOR and DEVICE_MODEL as used by
all other targets.

Signed-off-by: Moritz Warning <moritzwarning@web.de>
2021-09-23 21:45:30 -10:00
Moritz Warning
e2f284dbd1 x86: use device vendor/model variable
Remove use of DEVICE_TITLE in favor of the
DEVICE_VENDOR and DEVICE_MODEL as used by
all other targets.

Signed-off-by: Moritz Warning <moritzwarning@web.de>
2021-09-23 21:45:13 -10:00
Paul Spooren
a7fdd4de59 imagebuilder: show architecture in make info output
Using `make info` show the current target, revision, default packages
and available profiles. This commits adds the used architecture.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2021-09-23 21:37:19 -10:00
Christian Lamparter
608baf44c6 bcm53xx: MR32: read mac-address from eeprom
Meraki wrote the ethernet MAC-address of the device
onto the eeprom (AT24C64) at the fixed location 0x66
to 0x6C. Let's fetch it from there.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-09-23 20:50:58 +02:00
Damien Mascord
fd67908647 scripts: mkits.sh: Allow legacy @ mode for dts creation
commit 5ec60cbe9d ("scripts: mkits.sh: replace @ with - in nodes")
broke support for Meraki MR32 and this patch makes the replacement
configurable allowing for specifying the @ or - or whatever character
that is desired to retain backwards compatibility with existing devices.

For example, this patch includes the fix for the Meraki MR32 in
target/linux/bcm53xx/image for meraki_mr32:

  DEVICE_DTS_DELIMITER := @
  DEVICE_DTS_CONFIG := config@1

Fixes: 5ec60cbe9d ("scripts: mkits.sh: replace @ with - in nodes")
Signed-off-by: Damien Mascord <tusker@tusker.org>
[Added tags, checkpatch.pl fixes, noted that this is for old stuff]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-09-23 20:49:32 +02:00
Rafał Miłecki
366be2183e bcm53xx: backport early DT patches queued for 5.16
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-09-23 07:55:55 +02:00
Rosen Penev
f9050f1c43 bcm63xx: remove memcpy from mac assignment
With GCC11, memcpy doesn't work here as it assumes a size of 0. Use
ioremap to avoid it.

Fixed parameter type to match board_get_mac_address.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2021-09-21 15:46:19 -10:00
Felix Fietkau
a4b5bc20d7 kernel: add a bridge feature for filtering BPDU packets on ports
This will be used to ensure that APs don't transmit unnecessary STP packets

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-09-21 19:43:20 +02:00
Rafał Miłecki
0be4dea48e kernel: add missing CONFIG_NET_DSA_TAG_BRCM_LEGACY config symbol
This fixes:
Distributed Switch Architecture (NET_DSA) [Y/n/m/?] y
  Tag driver for Atheros AR9331 SoC with built-in switch (NET_DSA_TAG_AR9331) [N/m/y/?] n
  Tag driver for Broadcom switches using in-frame headers (NET_DSA_TAG_BRCM) [N/m/y/?] n
  Tag driver for Broadcom legacy switches using in-frame headers (NET_DSA_TAG_BRCM_LEGACY) [N/m/y/?] (NEW)
Error in reading or end of file.

Fixes: 8fa1b576bb ("linux: update b53 upstream driver")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-09-17 22:07:03 +02:00
Rafał Miłecki
8fa1b576bb linux: update b53 upstream driver
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-09-17 10:15:26 +02:00
Rafał Miłecki
a46fa5c3a7 bcm53xx: drop DTS based workaround for serial support in procd
Specifying serial in bootargs is not needed since the commit
ffeb37047e ("procd: update to git HEAD"). It's thanks to the procd
commit 2cfc26f8456a ("inittab: detect active console from kernel if no
console= specified").

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-09-16 07:59:50 +02:00
Daniel Golle
83672f506d
sunxi: add testing Linux 5.10
Add testing Linux kernel 5.10 for sunxi targets.

Removed patches were replaced by upstream commits:

- 410-v5.6-arm64-dts-allwinner-a64-olinuxino-Add-bank-supply-re.patch
   f0c3b29f56f0a arm64: dts: allwinner: a64: olinuxino: Add bank supply regulators

- 420-v5.7-arm64-dts-allwinner-a64-olinuxino-add-user-red-LED.patch
   89866b2667e0d arm64: dts: allwinner: a64: olinuxino: add user red LED

- 440-add-h6-pwm.patch
   a7fe985633f92 pwm: sun4i: Add an optional probe for reset line
   b8d74644f34a8 pwm: sun4i: Prefer "mod" clock to unnamed
   5b090b430d750 pwm: sun4i: Add an optional probe for bus clock
   fa4d81784681a pwm: sun4i: Always calculate params when applying new parameters
   9f28e95b5286f pwm: sun4i: Add support to output source clock directly
   fdd2c12e3761f pwm: sun4i: Add support for H6 PWM

- 441-arm64-dts-add-PWM-node.patch
   88432f5f8469b arm64: dts: allwinner: h6: Add PWM node

- 443-board-h6-orangepioneplus-fix-missing-ethernet.patch
   7ee32a17e0d65 arm64: dts: allwinner: h6: orangepi-one-plus: Enable ethernet

Run tested on friendlyarm,nanopi-neo (allwinner,sun8i-h3), looks all good.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-09-15 19:11:44 +01:00
Daniel Golle
47b531de32
sunxi: bring up DSA b53 switch on Lamobo R1
Build cortexa7 subtarget with DSA driver for MDIO-connected Broadcom
BCM53xxx switches. This is needed for the Lamobo R1 aka. BananaPi
BPi-R1 board which comes with such a switch IC.

Remove old swconfig driver from target kernel config as the only board
using it is now supported by the DSA driver.

No changes to device tree are needed as upstream DTS already got a
DSA switch definition and we are just using that upstream source.

Update default network config of the Lamobo R1 to create lan bridge
with all 4 lan ports.

Introduce DEVICE_COMPAT_VERSION for the board to inform users about
having the re-create their network configuration and add device alias
as Bananapi BPi-R1 while at it.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-09-15 19:11:29 +01:00
Daniel Danzberger
ba59466bf4 octeontx: add linux 5.10 testing kernel support
Changes from 5.4 to 5.10:
-------------------------
 - patches from 5.4 are all upstream for 5.10 execpt for
   0004-PCI-add-quirk-for-Gateworks-PLX-PEX860x-switch-with-.patch

 - disable block device data integrity (DIF/DIX/T10) in default config
   (CONFIG_BLK_DEV_INTEGRITY)
   This feature is only supported by:
     - Enterprise SAS/SCSI HBAs and Disks
     - Software raid
     - NVMEs with metadata capabilities (most don't have this)
   None of which are part of any octeontx boards.

 - arm64 TEXT_OFFSET (0x80000) has been removed after 5.4
   This will break Uimages with kernel load addresses that aren't 2MiB
   aligned any longer. Resulting in the kernel silently fail to boot.
   For Gatworks newport boards for example, the uimage kernel load
   and execute address is 0x20080000. These need to be changed to
   0x20000000 when running kernels beyond 5.4.

Tested-on: Gateworks Newport GW64xx

Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
2021-09-13 18:36:15 +02:00
Pawel Dembicki
0dbe754e43 kirkwood: increase kernel size of Linksyses
Linksyses Audi EA3500 and Viper E4200/E4500 have too small kernel
partition size when kernel 5.10 is used. This patch change kernel
partition to maximum size allowed by u-boot.

Kernel size is overlapping rootfs now, like mvebu Linksyses and stock
partition table. It fix  back to stock via sysupgrade, which was broken
since 18.06.

Fixes: 9808b9ae02 ("kirkwood: switch to kernel 4.9")

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2021-09-13 18:36:15 +02:00
Soma Zambelly
c5b44af2fc realtek: add ZyXEL GS1900-24HPv2 support
The ZyXEL GS1900-24HPv2 is a 24 port PoE switch with two SFP ports, similar to the other GS1900 switches.

Specifications
--------------
* Device:    ZyXEL GS1900-24HPv2
* SoC:       Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash:     16 MiB
* RAM:       W631GG8MB-12 128 MiB DDR3 SDRAM
             (stock firmware is configured to use only 64 MiB)
* Ethernet:  24x 10/100/1000 Mbps, 2x SFP 100/1000 Mbps
* LEDs:      1 PWR LED (green, not configurable)
             1 SYS LED (green, configurable)
             24 ethernet port link/activity LEDs (green, SoC controlled)
             24 ethernet port PoE status LEDs
             2 SFP status/activity LEDs (green, SoC controlled)
* Buttons:   1 "RESTORE" button on front panel
             1 "RESET" button on front panel
* Power      120-240V AC C13
* UART:      1 serial header (J41) with populated standard pin connector on
             the left edge of the PCB, angled towards the side.
             The casing has a rectangular cutout on the side that provides
             external access to these pins.
             Pinout (front to back):
             + GND
             + TX
             + RX
             + VCC

Serial connection parameters for both devices: 115200 8N1.

Installation
------------

OEM upgrade method:

(Possible on master once https://patchwork.ozlabs.org/project/openwrt/patch/20210624210408.19248-1-bjorn@mork.no/ is merged)

* Log in to OEM management web interface
* Navigate to Maintenance > Firmware > Management
* If "Active Image" has the first option selected, OpenWrt will need to be
  flashed to the "Active" partition. If the second option is selected,
  OpenWrt will need to be flashed to the "Backup" partition.
* Navigate to Maintenance > Firmware > Upload
* Upload the openwrt-realtek-generic-zyxel_gs1900-24hp-v2-initramfs-kernel.bin
  file by your preferred method to the previously determined partition.
  When prompted, select to boot from the newly flashed image, and reboot the switch.
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
   > sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-24hp-v2-squashfs-sysupgrade.bin
   it may be necessary to restart the network (/etc/init.d/network restart) on
   the running initramfs image.

U-Boot TFTP method:

* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
  space bar, and enable the network:
   > rtk network on
* Since the GS1900-24HPv2 is a dual-partition device, you want to keep the OEM
  firmware on the backup partition for the time being. OpenWrt can only boot
  from the first partition anyway (hardcoded in the DTS). To make sure we are
  manipulating the first partition, issue the following commands:
  > setsys bootpartition 0
  > savesys
* Download the image onto the device and boot from it:
   > tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-24hp-v2-initramfs-kernel.bin
   > bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
   > sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-24hp-v2-squashfs-sysupgrade.bin
   it may be necessary to restart the network (/etc/init.d/network restart) on
   the running initramfs image.

Signed-off-by: Soma Zambelly <zambelly.soma@gmail.com>
2021-09-13 18:36:15 +02:00
Zhao Yu
3d4867addf sunxi: enable MUSB in A7 subtarget
like commit 78c1ed6. Without this,Some USB port on H3 baseboard
can' work. So, need enable MUSB support on this target.

Signed-off-by: Zhao Yu <574249312@qq.com>
2021-09-13 18:36:15 +02:00
Fabian Bläse
c50ece58c4 kernel: backport switchdev fix for bridge in bridge configurations
This patch fixes the forwarding behavior of bridge in bridge
configurations with DSA.

Without it, the configuration of the upper bridge might overwrite
settings of the lower bridge. For example, a vlan-aware bridge
with DSA interfaces in it might be offloaded to the DSA hardware. If the
bridge interface itself gets slave of a different bridge without vlan
filtering, the vlan filtering setting of the lower bridge is overwritten
by the upper bridge, which results in an incorrect hardware
configuration.

This was backported from kernel 5.7.

Ref: https://lore.kernel.org/netdev/20191222192235.GK25745@shell.armlinux.org.uk/
Fixes: FS#3996
Signed-off-by: Fabian Bläse <fabian@blaese.de>
2021-09-13 17:11:50 +02:00
John Audia
a88b32bf6e kernel: bump 5.4 to 5.4.145
Removed upstreamed:
  generic-backport/040-ARM-8918-2-only-build-return_address-if-needed.patch

All other patches automatically rebased.

Build system: x86_64
Build-tested: ipq806x/R7800

Signed-off-by: John Audia <graysky@archlinux.us>
2021-09-13 17:08:17 +02:00
John Audia
51c7e1d25f kernel: bump 5.4 to 5.4.144
Manually rebased:
  backport-5.4/370-netfilter-nf_flow_table-fix-offloaded-connection-tim.patch

All other patches automatically rebased.

Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800

Signed-off-by: John Audia <graysky@archlinux.us>
2021-09-13 17:08:17 +02:00
John Audia
5fb4cb07e2 kernel: bump 5.10 to 5.10.64
All patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, ipq806x/R7800
Run-tested: bcm2711/RPi4B, ipq806x/R7800

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
2021-09-13 17:08:17 +02:00
Matt Merhar
55643e469c kernel: fix jffs2 compilation with GCC_PLUGIN_RANDSTRUCT enabled
Designated initializers are required when using the randstruct GCC
plugin, otherwise an error like the following is seen:

./include/linux/lzma.h:60:31: error: positional initialization of field in 'struct' declared with 'designated_init' attribute [-Werror=designated-init]

Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
2021-09-13 17:08:12 +02:00
Hauke Mehrtens
1a3b3dc797 kernel: Add missing kernel config options
These options are selectable when some of the kernel debug options like
KERNEL_SOFTLOCKUP_DETECTOR are selected.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-09-13 13:04:21 +02:00
Ansuel Smith
0470159552 ipq806x: switch to kernel 5.10
Move kernel version to 5.10 as has been tested by many users
with positive feedback.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[Tested on: ipq8064/g10; ipq8065/nbg6817]
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2021-09-12 18:52:30 +02:00
Sven Eckelmann
c7e9335e4c ipq40xx: Fix board-2.bin package name for Plasma Cloud PA2200
The board data file for the Plasma Cloud PA2200 is not part of the default
board-2.bin which is shipped by ath10k-board-qca4019. A typo in the device
package name resulted in a not correctly selected package for the device
specific board-2.bin. The wifi driver has therefore loaded the wrong
calibration information into the wifi chip.

Fixes: 4871fd2616 ("ipq40xx: add support for Plasma Cloud PA2200")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2021-09-12 18:52:30 +02:00
Sven Eckelmann
d0ffc17535 ipq40xx: Fix board-2.bin package name for Plasma Cloud PA1200
The board data file for the Plasma Cloud PA1200 is not part of the default
board-2.bin which is shipped by ath10k-board-qca4019. A typo in the device
package name resulted in a not correctly selected package for the device
specific board-2.bin. The wifi driver has therefore loaded the wrong
calibration information into the wifi chip.

Fixes: ea5bb6bbfe ("ipq40xx: add support for Plasma Cloud PA1200")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2021-09-12 18:52:30 +02:00
Sven Eckelmann
14bd392a1c ipq40xx: Select correct board-2.bin for EnGenius EMR3500
The board data file for the EnGenius EMR3500 is not part of the default
board-2.bin which is shipped by ath10k-board-qca4019. As result, the wrong
calibration information will be loaded into the wifi chip.

Fixes: 3f61e5e1b9 ("ipq40xx: add support for EnGenius EMR3500")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2021-09-12 18:52:30 +02:00
Sven Eckelmann
d9f4a4280e ipq40xx: Select correct board-2.bin for EnGenius EMD1
The board data file for the EnGenius EMD1 is not part of the default
board-2.bin which is shipped by ath10k-board-qca4019. As result, the wrong
calibration information will be loaded into the wifi chip.

Fixes: 51f3035978 ("ipq40xx: add support for EnGenius EMD1")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2021-09-12 18:52:30 +02:00
Rui Salvaterra
27199a4e66 kernel: bump 5.10 to 5.10.62
Patches automatically refreshed.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-09-09 23:40:32 +02:00
Ian Chang
70c75965a9 mvebu: add support for iEi Puzzle-M901/Puzzle-M902
Hardware specification
 ----------------------
 * CN9130 SoC, Quad-core ARMv8 Cortex-72 @ 2200 MHz
 * 4 GB DDR
 * 4 GB eMMC
 * mmcblk0
 - mmcblk0p1    64M  kernel_1
 - mmcblk0p2    64M  kernel_2
 - mmcblk0p3   512M  rootfs_1
 - mmcblk0p4   512M  rootfs_2
 - mmcblk0p5   512M  Reserved
 - mmcblk0p6    64M  Reserved
 - mmcblk0p7   1.8G  rootfs_data

 * 4 MB (SPI Flash)
 * 6 x 2.5 Gigabit  ports (Puzzle-M901)
 - External PHY with 6 ports (AQR112R)

 * 6 x 2.5 Gigabit ports (Puzzle-M902)
 - External PHY with 6 ports (AQR112R)
   3 x 10 Gigabit ports (Puzzle-M902)
 - External PHY with 3 ports (AQR113R)

 * 4 x Front panel LED
 * 1 x USB 3.0
 * Reset button on Rear panel
 * UART (115200 8N1,header on PCB)

 Flash instructions:
    The original firmware is based on OpenWrt.
    Flash firmware using LuCI and CLI

Signed-off-by: Ian Chang <ianchang@ieiworld.com>
2021-09-09 23:36:13 +02:00
Ian Chang
c98ddf0f01 mvebu: backport CN9130 dts necessary files changes to 5.4
1. Add support for Marvell CN9130 SoC
 2. Add support for CP115,and create an armada-cp11x.dtsi file which will be used to instantiate both CP110 and CP115
 3. Add support for AP807/AP807-quad,AP807 is a major component of CN9130 SoC series
 4. Drop PCIe I/O ranges from CP11x file and externalize PCIe macros from CP11x file

Signed-off-by: Ian Chang <ianchang@ieiworld.com>
2021-09-09 23:36:13 +02:00
Hauke Mehrtens
b9cc16a5e8 kernel: Set CONFIG_RCU_CPU_STALL_TIMEOUT=21
The default value for CONFIG_RCU_CPU_STALL_TIMEOUT was changed from 60
seconds to 21 seconds in 2012 in the upstream kernel. Some targets
already use 21 seconds.

This patch changes the default value in the generic configuration to 21
seconds and removes the target specific configuration options.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-09-09 20:24:12 +02:00
Paul Spooren
64be0eadc1 x86: switch to kernel 5.10
Seems to be working fine in QEMU and the wild.

Signed-off-by: Paul Spooren <mail@aparcar.org>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-09-08 13:29:43 -10:00
Rui Salvaterra
c9042202ad mvebu: switch to kernel 5.10
It's been brewing on my cortexa9 subtarget (Turris Omnia) for months.
Perfectly stable.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
[modify subject to match previous updates]
Signed-off-by: Paul Spooren <mail@aparcar.org>
2021-09-08 13:28:22 -10:00
Rafał Miłecki
ae33ce2af2 bcm53xx: specify switch ports for more devices
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-09-07 13:23:16 +02:00
Rafał Miłecki
854a4de10c linux: backport DSA b53 driver fixes for switch ports
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-09-07 13:23:13 +02:00
Andrea Poletti
de0c380a5f ramips: add support for Sitecom WLR-4100 v1 002
Sitecom WLR-4100 v1 002 (marked as X4 N300) is a wireless router
Specification:
SoC: MT7620A
RAM: 64 MB DDR2
Flash: MX25L6405D SPI NOR 8 MB
WIFI: 2.4 GHz integrated
Ethernet: 5x 10/100/1000 Mbps QCA8337
USB: 1x 2.0
LEDS: 2x GPIO controlled, 5x switch
Buttons: 1x GPIO controlled
UART: row of 4 unpopulated holes near USB port, starting count from
      white triangle on PCB:

    VCC 3.3V
    GND
    TX
    RX

    baud: 115200, parity: none, flow control: none

Installation

    Connect to one of LAN (yellow) ethernet ports,
    Open router configuration interface,
    Go to Toolbox > Firmware,
    Browse for OpenWrt factory image with dlf extension and hit Apply,
    Wait few minutes, after the Power LED will stop blinking, the router is
    ready for configuration.

Known issues
Some USB 2.0 devices work at full speed mode 1.1 only

MAC addresses

factory partition only contains one (binary) MAC address in 0x4.
u-boot-env contains four (ascii) MAC addresses, of which two appear
to be valid.

  factory     0x4       **:**:**:**:b9:84  binary
  u-boot-env  ethaddr   **:**:**:**:b9:84  ascii
  u-boot-env  wanaddr   **:**:**:**:b9:85  ascii
  u-boot-env  wlanaddr  00:AA:BB:CC:DD:12  ascii
  u-boot-env  iNICaddr  00:AA:BB:CC:DD:22  ascii

The factory firmware only assigns ethaddr. Thus, we take the
binary value which we can use directly in DTS.

Additional information
OEM firmware shell password is: SitecomSenao
useful for creating backup of original firmware.
There is also another revision of this device (v1 001), based on RT3352 SoC

Signed-off-by: Andrea Poletti <polex73@yahoo.it>
[remove config DT label, convert to nvmem, remove MAC address
 setup from u-boot-env, add MAC address info to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-09-05 23:52:35 +02:00
Robert Balas
baacdd53df ath79: add support for TP-Link TL-WA1201 v2
This device is a wireless access point working on the 2.4 GHz and 5 GHz
band, based on Qualcomm/Atheros QCA9563 + QCA9886.

Specification
- 775 MHz CPU
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- QCA9563: 2.4 GHz 3x3
- QCA9886: 5 GHz
- AR8033: 1x 1 Gbs Ethernet
- 4x LED, WPS factory reset and power button
- bare UART on PCB (accessible through testpoints)

Methods for Flashing:
- Apply factory image in OEM firmware web-gui. Wait a minute after the
  progress bar completes and restart the device.
- Sysupgrade on top of existing OpenWRT image
- Solder wires onto UART testpoints and attach a terminal.
  Boot the device and press enter to enter u-boot's menu. Then issue the
  following commands
  1. setenv serverip your-server-ip
     setenv ipaddr your-device-ip
  2. tftp 0x80060000 openwrt-squashfs.bin (Rembember output of size in
    hex, henceforth "sizeinhex")
  3. erase 0x9f030000 +"sizeinhex"
  4. cp.b 0x80060000 0x9f030000 0x"sizeinhex"
  5. reboot

Recover:
- U-boot serial console

Signed-off-by: Robert Balas <balasr@iis.ee.ethz.ch>
[convert to nvmem]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-09-05 23:52:35 +02:00
Chuanhong Guo
43f0e386d4 mediatek: add support for TOTOLINK A8000RU
Specifications:
- SoC: MT7622
- RAM: 512MB
- Flash: MX35LF1GE4AB 128MB SPI NAND
- Ethernet: RTL8367S 5x1GbE
- WiFi: 2.4G: MT7622 5G: MT7615N x2
- Other ports: USB3.0 x1

Flash instruction:
*important*: upgrade vendor firmware to at least V7.1cu.643_B20200521
1. hold the reset button and power on the device. wait for about 10s
   before releasing the reset button.
2. upload sysupgrade.bin via u-boot recovery page on http://192.168.1.1

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2021-09-03 15:53:28 +08:00
Rui Salvaterra
42ee7d8157 kernel: add missing CONFIG_SECURITY_NETWORK_XFRM ksym
Paul noticed a build failure [1] due to this missing symbol. Add it as disabled
to both generic kconfigs.

[1] https://github.com/aparcar/openwrt/runs/3480872706?check_suite_focus=true#step:11:63

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-08-31 22:41:46 -10:00
Rafał Miłecki
f55f1dbaad bcm53xx: switch to the kernel 5.10
With PCI and USB regressions fixed it should be safe to switch now.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-08-31 11:41:09 +02:00
Rafał Miłecki
9b40346328 bcm53xx: fix kmod-i2c-bcm-iproc for kernel 5.10
I2C_BCM_IPROC selects I2C_SLAVE which in turn makes two new symbols
available: I2C_SLAVE_EEPROM and I2C_SLAVE_TESTUNIT. That was causing:

I2C support (I2C) [M/n/y/?] m
  Enable compatibility bits for old user-space (I2C_COMPAT) [N/y/?] n
  I2C device interface (I2C_CHARDEV) [M/n/?] m
  I2C bus multiplexing support (I2C_MUX) [N/m/?] n
  Autoselect pertinent helper modules (I2C_HELPER_AUTO) [N/y/?] n
    SMBus-specific protocols (I2C_SMBUS) [N/m/?] n
  I2C/SMBus Test Stub (I2C_STUB) [N/m/?] n
  I2C slave support (I2C_SLAVE) [Y/?] y
    I2C eeprom slave driver (I2C_SLAVE_EEPROM) [N/m/?] n
    I2C eeprom testunit driver (I2C_SLAVE_TESTUNIT) [N/m/?] (NEW)

Ideally I2C_SLAVE should probably be packaged as kmod-i2c-slabe. For now
just modify kmod-i2c-bcm-iproc to fix kernel compilation.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-08-31 11:41:04 +02:00
Rafał Miłecki
62465c75be bcm53xx: fix USB in kernel 5.10
This makes USB controller driver work with USBs that are always powered
on (don't require toggling any GPIO).

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-08-31 09:34:40 +02:00
Alexander Couzens
c39be8e7a4
ramips: minew g1-c: use default static address for lan instead of dhcp
As Adrian Schmutzler suggested on github [1] the device should follow the
default behaviour on ethernet using a static address instead using dhcp.

[1] 8d497b6570

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2021-08-31 02:42:32 +02:00
Rafał Miłecki
8a4d4d4243 bcm53xx: backport missed DT patch cleaning up CRU block
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-08-30 09:00:28 +02:00
Sungbo Eo
f08b76b32f ramips: w2914ns-v2: consolidate leds nodes into dtsi
w2914ns-v2, 11acnas, and freezio use almost same board and thus share a
common dtsi file. Now that LED labels do not contain "devicename" since
commit c846dd91f0 ("ramips: remove model name from LED labels"), let's
move the leds nodes to dtsi and remove them from dts.

Note that freezio has only one USB 3.0 port and adding &ehci_port2 trigger
does not incur any visible changes.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2021-08-30 00:37:47 +02:00
Adrian Schmutzler
aec97b31ea ramips: provide default BLOCKSIZE for Device/seama
The Device/seama shared definition requires BLOCKSIZE, so it should
have a default value for this variable.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-08-30 00:37:47 +02:00
Filip Matijević
e2b03c16eb ipq806x: add missing enclosing partitions block for TP-Link C2600
The partitions that have compatible property set are skipped by mtd if
they are not contained inside a partitions node and this breaks
fetching MAC address from "default-mac" partition.

Fix this by defining all the partitions inside partitions node with
compatible = "fixed-partitions" as nvmem requires the standard
partitions scheme to work correctly.

Fixes: FS#3945
Fixes: cd36d71655 ("ipq806x/dts: Add Archer C2600 DTS")
Fixes: 0458a8993c ("ipq806x: convert mtd-mac-address to nvmem
implementation")

Signed-off-by: Filip Matijević <filip.matijevic.pz@gmail.com>
Reviewed-by: Ansuel Smith <ansuelsmth@gmail.com>
[adjust commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-08-30 00:37:35 +02:00
Adrian Schmutzler
d37125b3f3 ath79: remove redundant BLOCKSIZE of 64k from devices
BLOCKSIZE = 64k is set in Device/Default, i.e. global default on
the target.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-08-30 00:37:35 +02:00
Rafał Miłecki
bce00f47e5 bcm53xx: backport the latest upstream DT changes
This includes:
1. BCM5301X changes from 5.14 and queued 5.15 stuff
2. NSP changes from 5.11 - 5.15 for kernel 5.10

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-08-29 22:57:13 +02:00
Rui Salvaterra
505b7a2d08 kernel: move two symbols to the generic kconfigs
CONFIG_RCU_{NEED_SEGCBLIST,STALL_COMMON} are set basically everywhere. Move them
to the generic kconfigs. And resort the generic kconfigs while at it.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-08-29 17:07:19 +02:00
Rui Salvaterra
7e135add24 kernel: disable CONFIG_RCU_EXPERT and friends
Based on the existing documentation [1][2], I dare anyone to demonstrate that
we need to fine-tune these RCU parameters. The (performance) breakage potential
for doing so is immense, so let's just please put down this loaded footgun.

Disable CONFIG_RCU_EXPERT and its dependent symbols. Additionally, remove the
CONFIG_RCU_EXPERT symbol from the target kconfigs which contain it.

[1] https://www.kernel.org/doc/Documentation/RCU/Design/Data-Structures/Data-Structures.html
[2] https://lwn.net/Articles/777214/

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-08-29 17:03:38 +02:00
Ansuel Smith
b8f8d0651c kernel: fix warning about unused try_to_force_load
There is a longlasting warn about unused defined try_to_force_load.
Fix this by including this function only when actually used.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2021-08-29 16:31:24 +02:00
John Audia
be7e0091fe kernel: bump 5.4 to 5.4.143
Manually rebased:
  bcm27xx/patches-5.4/950-1031-net-lan78xx-Ack-pending-PHY-ints-when-resetting.patch

Removed upstreamed:
  mvebu/patches-5.4/100-cpufreq-armada-37xx-forbid-cpufreq-for-1.2-GHz-variant.patch

All other patches automatically rebased.

Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
2021-08-29 16:31:02 +02:00
John Audia
6b1cd3e345 kernel: bump 5.10 to 5.10.61
Manually rebased:
  bcm27xx/patches-5.10/950-1031-net-lan78xx-Ack-pending-PHY-ints-when-resetting.patch

Removed upstreamed:
  mvebu/patches-5.10/101-cpufreq-armada-37xx-forbid-cpufreq-for-1.2-GHz-variant.patch

All other patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B
Run-tested: bcm2711/RPi4B

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
2021-08-29 16:30:20 +02:00
Sebastian Schaper
1c8214d6f2 ath79: fix spelling of DEVICE_MODEL for D-Link DAP-2695
Change `DAP-2965` to `DAP-2695` for device selection in menuconfig.

Fixes: cd09f26660 ("ath79: add support for D-Link DAP-2695-A1")

Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
[add Fixes]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-08-28 13:24:23 +02:00
David Bauer
90e167abaa ramips: add label-mac for TL-MR3020 v3
The TP-Link TL-MR3020 v3 only has a single MAC address assigned for
ethernet LAN as well as WiFi. This MAC address is also printed on the
casing.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-08-28 01:35:02 +02:00
David Bauer
9c965893ed ramips: enable fast-read for TL-MR3020 v3
The GigaDevices GD25Q64B found on the TL-MR3020 v3 supports the fast
read instruction. Add the required DT property in order to enable usage
of this property.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-08-28 01:31:45 +02:00
David Bauer
db3545cd02 ramips: increase SPI frequency for TL-MR3020 v3
The GigaDevices GD25Q64B supports higher SPI clocks than 10 MHz. While
100 MHz do not work reliably, 50 MHz works without issues.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-08-28 01:31:36 +02:00
David Bauer
161ee85bbe ramips: fix input type for TL-MR3020 v3
The modec{1,2} keys are actually switches.

Add the respective DTS properties to avoid accidental activation of
failsafe mode.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-08-28 01:31:29 +02:00
Daniel Golle
cf40141b51
kernel: properly handle paging errors in fit partition parser
The uImage.FIT partition uses page mapping without properly handling
paging errors. This can lead to Kernel Oops in case of read errors
while trying to parse uImage.FIT partitions.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-08-27 21:32:43 +01:00
Chuanhong Guo
97e32e9702 mediatek: mt7623: replace kconfig symbol for snand driver
this change was missing during the spi-nand driver replacement, causing
build failure.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2021-08-27 22:22:29 +08:00
Chuanhong Guo
472437b93f mediatek: mt7629: manually add missing kconfig
These options doesn't show up unless some kernel packages are selected,
so they are not covered by kernel_menuconfig.
Manually add them so that a build with all kmods can pass without user
interaction.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2021-08-27 15:54:53 +08:00
Chuanhong Guo
8f2cace0b7 mediatek: mt7629: build with linux 5.10
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2021-08-27 10:26:25 +08:00
Chuanhong Guo
9abd2fb6c4 mediatek: bmt: set default bmt oob offset to 0
there's no driver level remapping of oob data in the new spi-nand
driver and bmt oob signature starts at 0x0 of the dumped oob data.
change the default value to 0 for the new spi-nand driver.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2021-08-27 10:26:25 +08:00
Chuanhong Guo
388127abd1 mediatek: mtk-snand: check request size against chip info
mtd->size will be overrided by BMT which makes all mtd requests made by
bmt fail in request size checking.
this commit changes the driver to check against actual chip size in chip
info as a workaround.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2021-08-27 10:26:25 +08:00
Chuanhong Guo
b600aee3ed mediatek: attach bmt to the new snand driver
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2021-08-27 10:26:25 +08:00
Chuanhong Guo
01b452fe2d mediatek: change dts to use the new snand driver
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2021-08-27 10:26:25 +08:00
Chuanhong Guo
c6ed31630d mediatek: remove spi-nand hacks from 5.10
we now have a standalone mtd driver and the old spi-mem driver along
with the hack in spi-nand core can be removed.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2021-08-27 10:26:25 +08:00
Weijie Gao
e8e8487603 mediatek: enable new spi-nand driver for kernel 5.10
This patch enables new spi-nand driver for mt7622 and mt7629.

Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2021-08-27 10:26:25 +08:00
Weijie Gao
050621aa01 mediatek: add a new spi-nand driver for kernel 5.10
This patch adds a new spi-nand driver which implements the SNFI of mt7622
and mt7629.

Unlike the existing snfi driver which makes use of the spi-mem framework
and the spi-nand framework with modified ecc support, this driver is
implemented directly on the mtd framework with other components untouched,
and provides better performance, and behaves exactly the same as the nand
framework.

Signed-off-by: Weijie Gao <hackpascal@gmail.com>
2021-08-27 10:26:24 +08:00
Christian Lamparter
a1bd8109f0 ath79: remove obsolete pci-ath9k-fixup.[c,h] files
This was old code from the AR71XXs target days that
doesn't get compiled and used anymore.

Bringing up AR92xx and earlier chips from their
OWL-Emulator state is currently done by the upstream
ath9k-pci-owl-loader module. (see the kmod-owl-loader
package).

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-08-26 21:00:26 +02:00
Jan-Niklas Burfeind
d98738b5c1 ath79: add support for onion omega
The Onion Omega is a hardware development platform with built-in WiFi.

https://onioniot.github.io/wiki/

Specifications:
 - QCA9331 @ 400 MHz (MIPS 24Kc Big-Endian Processor)
 - 64MB of DDR2 RAM running at 400 MHz
 - 16MB of on-board flash storage
 - Support for USB 2.0
 - Support for Ethernet at 100 Mbps
 - 802.11b/g/n WiFi at 150 Mbps
 - 18 digital GPIOs
 - A single Serial UART
 - Support for SPI
 - Support for I2S

Flash instructions:
The device is running OpenWrt upon release using the ar71xx target.
Both a sysupgrade
and uploading the factory image using u-boots web-UI do work fine.

Depending on the ssh client, it might be necessary to enable outdated
KeyExchange methods e.g. in the clients ssh-config:

Host 192.168.1.1
        KexAlgorithms +diffie-hellman-group1-sha1

The stock credentials are: root onioneer

For u-boots web-UI manually configure `192.168.1.2/24` on your computer,
connect to `192.168.1.1`.

MAC addresses as verified by OEM firmware:
2G       phy0      label
LAN      eth0      label - 1

LAN is only available in combination with an optional expansion dock.

Based on vendor acked commit:
commit 5cd49bb067 ("ar71xx: add support for Onion Omega")

Partly reverts:
commit fc553c7e4c ("ath79: drop unused/incomplete dts")

Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
2021-08-26 15:07:18 +02:00
Álvaro Fernández Rojas
4ab0b5fabd bmips: backport accepted watchdog patch
This patch has been accepted for linux v5.14.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-08-25 10:24:33 +02:00
David Yang
38cb500516 ramips: expose ephy leds for miwifi-mini
Give users more control by exposing ephy leds.

Signed-off-by: David Yang <mmyangfl@gmail.com>
[remove execute bit on 01_leds, add status for gpio2]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-08-25 01:42:17 +02:00
David Yang
5ed11012e7 ramips: lock u-boot partition and unlock u-boot-env for miwifi-mini
Generally u-boot should keep read-only to avoid mis-overwriting and
bricking the device, but u-boot-env could be safely modified with u-boot
setenv tool.

Signed-off-by: David Yang <mmyangfl@gmail.com>
2021-08-25 01:42:17 +02:00
David Yang
a6c410ae10 ramips: increase flash freq for miwifi-mini
The flash is Winbond 25Q128. As it has large rom, better to increase flash
frequency to 70MHz according to the flash spec and enable fast-read.

Signed-off-by: David Yang <mmyangfl@gmail.com>
2021-08-25 01:42:17 +02:00
Giovanni Cascione
d57ba86e48 ramips: add support for D-Link DAP-1325-A1
This patch adds support for D-Link DAP-1325-A1 (Range Extender Wi-Fi N300)

Specifications:
- SoC: 580Mhz MT7628NN
- RAM: 64MB, DDR2 SDRAM
- Storage: 8MB, SPI (W25Q64JVSSIQ)
- Ethernet: 1x 10/100 LAN port
- WIFI: 2.4 GHz 802.11bgn
- LED: Status (2x to provide 3 colors), Wi-Fi Signal Strength (4x)
- Buttons: Reset, WPS
- UART: Serial console (57600, 8n1)
Row of 4 holes near LAN port, starting from square hole:
3.3V, TX,RX,GND
- FCC ID: fccid.io/KA2AP1325A1/

Installation:

Failsafe UI
Firmware can be uploaded with Failsafe UI web page:
- turn device off
- press and hold reset button
- turn device on
- keep holding reset until red wifi strength led turns on (ab. 10sec)
- connect to device through LAN port
PC must be configured with static ip (192.168.0.x)
- connect to 192.168.0.50
- select image to be flashed and upload.
Device will reboot after successful update

Serial port/TFTP server
- Connect through serial connectors on PCB (e.g. with teraterm)
- Set up a TFTP server, and connect through LAN with static IP
- Put image file in the root of the server
- Boot the device and select '2' at U-Boot startup
- Set device IP, server IP and image file name
- Start upload and flash

Signed-off-by: Giovanni Cascione <ing.cascione@gmail.com>
[fix whitespaces in DTS, convert to nvmem, add mtd-eeprom]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-08-25 01:42:17 +02:00