This driver allows retrieving MAC addresses and other factory information
via the NVMEM framework on Adtran devices.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Building HWMON as module prevents some other drivers from getting built
into the kernel, e.g. mxl-gpy. Always enable HWMON and also set
THERMAL_HWMON.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport newly introduced support for 'active-high' property and use
it to correctly implement polarity assignment for Aquantia PHY LEDs.
Previously the 'active-low' property was used to switch a LED PIN to
active-high ("drive VDD" in Aquantia-speak) mode.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Beside the already existing control of the
Blue cover LED, this will also add the
Green and the Red cover LEDS available in the
Asus TUF-AX6000.
Signed-off-by: Magnus Sandin <magnus.sandin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16632
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The previous iteration of MediaTek's PHY patches caused various weird bugs.
Drop culprit patch 733-10-net-phy-mediatek-Extend-1G-TX-RX-link-pulse-time.patch
and use the most recent iteration of the patchset which has been posted to the
netdev mailing list.
Link: https://patchwork.kernel.org/project/netdevbpf/list/?series=895513&state=*
Fixes: #16448
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The u-boot,env driver does not have layout in compatible.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16616
Signed-off-by: Robert Marko <robimarko@gmail.com>
Select MT7996 2+3+3 firmware for the Adtran SmartRG SDG-8733A device
and also add it to the image for the BPi-R4 which supports both,
BE19000 (4+5+5) as well as BE14000 (2+3+3) Wi-Fi 7 modules.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add u-boot support based on the kernel dts introduced in d1016446 and
the GL-MT6000 u-boot support in fe10f974.
The pcie-mediatek-gen3 kernel driver doesn't like hotplug, so to work in
PCIe mode, the 5G modem on this device needs to be switched on by u-boot
before starting the kernel. Include an init_modem step in the boot_system
action to set the relevant gpios. (The factory bootloader does the same,
using Mediatek SDK-specific gpio_power_clr and gpio_pull_up.)
Ideally the modem would be started using gpio-hog in the device tree, but
this will need to wait until mediatek gpio-hog support is fixed upstream:
https://lore.kernel.org/u-boot/6ef2583e85eea60560d7776377d662779e7c44e5.1722419839.git.chris@arachsys.com/
The bootloader can be replaced using the built-in web interface of the
factory bootloader. Hold the reset button for five seconds while powering
on the device and it will boot into a recovery http server.
http://192.168.1.1/uboot.html and http://192.168.1.1/bl2.html can then
be used to upload openwrt-mediatek-filogic-glinet_gl-x3000-bl31-uboot.fip
and openwrt-mediatek-filogic-glinet_gl-x3000-preloader.bin respectively.
Alternatively, from a root shell on the running system, unlock the boot
partition with
echo 0 >/sys/block/mmcblk0boot0/force_ro
then write openwrt-mediatek-filogic-glinet_gl-x3000-bl31-uboot.fip to
/dev/mmcblk0p4 and openwrt-mediatek-filogic-glinet_gl-x3000-preloader.bin
to /dev/mmcblk0boot0.
Signed-off-by: Chris Webb <chris@arachsys.com>
Link: https://github.com/openwrt/openwrt/pull/15645
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification is similar to other devices of the MT Stuart series:
* Mediatek MT7988D (3x Cortex-A73, up to 1.8 GHz clock speed)
* 8 GiB eMMC
* 2 GiB DDR4 RAM
* 2500M/1000M/100M LAN port
* 10000M/5000M/2500M/1000M/100M/10M WAN port
* MT7992 Tri-band (2.4G, 5G, 6G) 2T2R+3T3R+3T3R 802.11be Wi-Fi
* Renesas DA14531MOD Bluetooth
* 2 buttons (Reset, Mesh/WPS)
* uC-controlled RGB LED via I2C
* 2x LED for the 2.5G port, 3x LED for the 10G port
* 3.3V-level 115200 baud UART console via 4-pin Dupont connector
exposed at the bottom of the device
* USB-C PD power input
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Instead of reading it from flash directly, let U-Boot assign the LAN
MAC address. Set label-mac-device while at it and sort aliases in DT
alphabetically.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fix a typo in the MAC address assignment script affecting SDG-8734.
Fixes: c71b68acdd ("mediatek: filogic: add Adtran SmartRG Mount Stuart series")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Apply changes suggested by SkyLake Huang for pending series improving
MediaTek Ethernet PHY drivers.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
configure 2.5G PHY LEDs to:
2500/1000: green with blink on TX/RX
100/10: green+yellow with blink on TX/RX
which is similar to other 1G PHY LEDs, which are:
1000: green with blink on TX/RX
100/10: green+yellow with blink on TX/RX
Fixes: 6cc14bf66a ("filogic: support Telenor branded ZyXEL EX5700")
Signed-off-by: Yan Cangang <nalanzeyu@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16082
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
MediaTek SDK uses eth2 as additional LAN port and eth1 as WAN.
Do the same also in OpenWrt to keep settings aligned with the SDK.
Suggested-by: Bc-bocun Chen <bc-bocun.chen@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
All boards using the deprecated uImage.FIT partition parser have
been migrated to the new fitblk driver. Drop the now no longer
needed partition parser.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The company Zyxel rebranded some years ago.
Currently the casing is according to the old branding even
for newer devices which already use the new branding.
This commit aligns the casing of Zyxel everywhere.
Signed-off-by: Goetz Goerisch <ggoerisch@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15652
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The commit backporting new MTK patches did not update the
Kernel config for mediatek/mt7622 causing the build to
fail.
Simply use the new config symbol name for the driver to
fix the issue.
Fixes: 1069514978 ("mediatek: backport pending Ethernet PHY driver patches")
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Link: https://github.com/openwrt/openwrt/pull/16225
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use pending patchset for 2.5GE PHY driver, unifying LED handling
accross all MediaTek Ethernet PHYs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Specification:
- MT7629 CPU
- MT7531 switch
- MT7761N and MT7762N wifi
- 256 MB RAM
- 128 MB NAND flash with dual-boot partitions
- 2 buttons: WPS and reset
- 1 WAN port (1G)
- 4 LAN ports (1G)
- 1 USB port
Limitations (same as other MT7629/MT7761N/MT7762N devices):
- Wifi is not working
- Second core is not working (kernel error message "CPU1: failed to come online")
Disassembly:
- There are two screws under the front rubber feet and two under the label on the bottom (in the corners towards the back, you should be able to feel them).
Serial Interface:
- UART pin header is already soldered on the board. Pinning from front to back:
1 - VCC
2 - TX
3 - RX
4 - n/a
5 - GND
GPIO:
- 1 white LED, connected to GPIO 52
- 1 reset button, connected to GPIO 60
- 1 WPS button, connected to GPIO 58
MAC Adresses:
- The MAC address printed on the device label is used for LAN and WAN
- The MAC address is stored in the devinfo partition in ASCII format (hw_mac_addr=aa:bb:cc:dd:ee)
- 2.4 GHz wifi uses MAC of the device label + 1
- 5 GHz wifi uses MAC of the device label + 2
Flashing:
- OpenWrt is only runnig in the first partition of dual boot
- To ensure to be able to go back to the factory image, flash the last OEM firmware via OEM web interface. This will ensure that the OEM firmware is present on both partitions
- Because of dual boot partitions, flashing via OEM interface is not supported
- Start a TFTP server and provide the initramfs image. Default settings:
- Router IP: 192.168.1.1
- TFTP server IP: 192.168.1.100
- TFTP file name: 7531.bin
- Open the device, connect UART and select " 1. System Load Linux to SDRAM via TFTP." during startup
- Adapt the settings to your environment, if required
- After initramfs is booted, flash the sysupgrade image
Return to OEM firmware:
- Run the following commands in OpenWrt to switch to the second partition
fw_setenv boot_part 2
fw_setenv bootimage 2
- Reboot the device. OEM firmware will start up again
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16067
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Also migrate mt7623 to new fitblk support scripts which simplify
sysupgrade when using uImage.FIT. This had been forgotten previously.
Fixes: 4448d6325f ("mediatek: make use of common uImage.FIT upgrade functions")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fix a use-after-free bug in mtk_wed_setup_tc_block_cb()
which leads to kernel panic when setup multiple ap
interfaces on one band of mt798x.
Signed-off-by: Zheng Zhang <everything411@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16118
Signed-off-by: Robert Marko <robimarko@gmail.com>
Read the 'fip' static volume in order to trigger scrubbing in case of
detecting flipped bits while reading.
We have to do this in Linux because we never read or touch the 'fip'
volume and the UBISPL implementation in ARM TrustedFirmware-A does NOT
handle scrubbing itself.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reporting an unclean read from SPI-NAND only when the maximum number
of correctable bitflip errors has been hit seems a bit late.
UBI LEB scrubbing, which depends on the lower MTD device reporting
correctable bitflips, then only kicks in when it's almost too late.
Set bitflip_threshold to 75% of the ECC strength, which is also the
default for raw NAND.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
According to RTL8221B's datasheet, the PHY requires at least 10ms
for assert and 68ms (recommended) for de-assert. So increase the
assert/de-assert time to 15ms and 68ms respectively.
Fixes: c0c3234e17 ("mediatek: add support for JDCloud RE-CP-03")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16106
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
CI says patches need to be refreshed, so do so.
Fixes: 6bb334c5cf ("mediatek: fix u-boot env layout NVMEM definitions")
Link: https://github.com/openwrt/openwrt/pull/16051
Signed-off-by: Robert Marko <robimarko@gmail.com>
Hardware specification:
SoC: MediaTek MT7986A 4x A53
Flash: ESMT F50L1G41LB 128MB
RAM: MT40A512M16TB-062ER 1GB
Ethernet: 2x 2.5G, 4x 1G Lan
WiFi1: MT7976GN 2.4GHz 4T4R
WiFi2: MT7976AN 5.2GHz 4T4R
WiFi3: MT7915AN 5.8GHz 4T4R
Button: Reset, WPS, Turbo
USB: 1 x USB 3.0
Power: DC 12V 5A
Flash instructions:
1. Execute the following operation to open nc shell:
https://openwrt.org/inbox/toh/tp-link/xdr-6086#rooting
2. Replace the stock bootloader to OpenWrt's:
dd bs=131072 conv=sync of=/dev/mtdblock9 if=/tmp/xxx-preloader.bin
dd bs=131072 conv=sync of=/dev/mtdblock9 seek=28 if=/tmp/xxx-bl31-uboot.fip
3. Connect to your PC via the Gigabit port of the router,
set a static ip on the ethernet interface of your PC.
4. Download the initramfs image, and restart the router,
waiting for tftp recovery to complete.
5. After openwrt boots up, perform sysupgrade.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/15930
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
