We have IPQ8064 AP161 board which has three GMAC's
* RGMII x2
* SGMII x1.
The existing ar8327 driver does not have support for
three GMAC's connection, hence this change adds support
for the same. This has been verified on AP148 and AP161
board.
Signed-off-by: xiaofeis <xiaofeis@codeaurora.org>
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
Multicast ARL entries can have multiple destination ports. Get and dump
all destination ports of each entry, not just the lowest.
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
Add support to allow for per switch port VLAN priority (PCP) bits
for the ar8327/8337 chip using the swconfig utility.
Tested on Netgear R7800
Signed-off-by: Tan Hong Hui <hhtan72@yahoo.com>
The implementation is not efficient on ar8xxx switches. It triggers high
CPU load and degrades device performance.
The high CPU load has been traced down to the ar8xxx_reg_wait() call in
ar8xxx_mib_op(), which has to usleep_range() till the MIB busy flag set
by the request to update the MIB counter is cleared.
This commit removes the get_port_stats() code introduced in 4d8a66d and
leaves a note for future hacker's beware.
Fixes: FS#1004
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch provides a generic switch_dev_ops 'get_port_stats()' callback by
taping into the relevant port MIB counters.
The implementation uses a generic callback that select the correct MIB counter
index based on chip version.
This callback is used by swconfig_leds led trigger to blink LEDs with port
network traffic.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
Imported from https://source.codeaurora.org/quic/qsdk/system/openwrt/commit/?h=korg/linux-3.4.y/release/arugula_bb_cs&id=2be4f8a8b205ae1a37db44839864451ebe893e6e
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Enable flow control of LAN and WAN ports to
get better performance.
Setup pvid as 0 for all ports during initialisation
to avoid confusion during system or switch INIT.
Disable PORT MAC before config MAC to avoid it work abnormal.
This change is for IR-054144, IR-057315.
Change-Id: I345f3dffa59ad3f97150e09692723da12a7b1067
Signed-off-by: Zou Shunxiang <shunxian@codeaurora.org>
Signed-off-by: xiaofeis <xiaofeis@codeaurora.org>
Combine all bus operations for one MMD access in one function.
Protecting all these bus operations with one lock also helps
to avoid potential issues due to bus operations intercepting
the register and data write.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 48914
The default TTL for address resolution table entries is 5 minutes
for all members of the AR8216 family. This can cause issues if
e.g. Wifi clients roam to another AP and their MAC appears on
another switch port suddenly. Then the client may not be reachable
until the old ARL entry expires.
I would have expected the switch to invalidate old entries if it
detects the same MAC on another port. But that's not the case.
Therefore make the TTL for ARL entries configurable.
The effective TTL will always be a multiple of 7 seconds.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 48913
Adds functions for flushing ARL table entries per port.
Successfully tested on AR8327. Implementation for AR8216/AR8236/AR8316
is based on the AR8236 datasheet and assumes that the three chips
share a common ATU register layout.
Compile-tested only for AR8216/AR8236/AR8316.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 46380
Adds the chip-specific part of reading ARL table for AR8216/AR8236/AR8316.
It's based on the AR8236 datasheet and compile-tested only as I couldn't
find datasheets for AR8216/AR8316 and don't own devices with these chips.
The existing ar8216_atu_flush implementation was used for all three
chip types, therefore I guess they share a common ATU register layout.
More testing would be appreciated.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 46379
Add global read-only swconfig attribute "arl_table" to display the
address resolution table.
So far the chip-specific part is implemented for AR8327/AR8337 only
as I don't have the datasheets for the other AR8XXX chips.
Successfully tested on TL-WDR4300 (AR8327rev2)
and TL-WDR4900 (AR8327rev4).
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 44104
Until a few years ago the page switch wait time was set to msleep(1)
what was changed to usleep_range(1000, 2000) later.
I can not imagine that a low-level operation like switching page
on register level takes so much time.
Most likely the value of 1ms was initially set to check whether
it fixes an issue and then remained w/o further checking whether
also a smaller value would be sufficient.
Now the wait time is set to 5us and I successfully tested this on
AR8327. IMHO 5us should be plenty of time for all supported chips.
However I couldn't test this due to missing hardware.
If other chips should need a longer wait time we can add the
wait time as a parameter to the ar8xxx_chip struct.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 44103
Check for switch port link changes and
- flush ATU in case of a change
- report link change via syslog
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 44102
AR8327/AR8337 allow to read the result of EEE autonegotiation.
If EEE is autonegotiated between the link partners, display
this as part of the swconfig get_link attribute.
eee100: 100MBit EEE supported by both link partners
eee1000: 1GBit EEE supported by both link partners
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 44022
Users reported network issues with AR8327 which turned out to be caused
by EEE not working correctly with certain link partners (ticket 14597).
The workaround was to disable EEE on all ports (changeset 41577).
The issue was with certain link partners only, therefore this patch
allows to control usage of EEE per port via swconfig.
Still the default is to initially disable EEE on all ports.
Successfully tested on a TL-WDR4900 (AR8327 rev.4)
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 44021
Move all AR8327/AR8337-specific driver code into a separate source file
ar8327.c and adjust patches so that ar8327.c is compiled if
CONFIG_AR8216_PHY is set.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43845
Move several structure definitions and #defines from ar8216.c
to ar8216.h and move AR8327/AR8337 header stuff into a new
header file ar8327.h.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43844
All supported switches have 5 PHYs. Currently partially 5 is hardcoded
and partially switch-specific constants exist.
Replace them with a global constant.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43328
This patch is needed to use the switch inside the Sitecom WLR-8100;
it was unusable and detected as Generic-Phy before.
since ar8337 is behaving like ar8327
generally do the same thing
see: https://forum.openwrt.org/viewtopic.php?pid=214218#p214218
forward-ported to trunk
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
Patchwork: http://patchwork.openwrt.org/patch/4469/
[juhosg: merge chip_is_ar83[23]7 statements in ar8xxx_phy_config_init]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38952
Tested on Buffalo WZR-600DHP with ar8316 switch. Commands used to mirror both
RX and TX traffic from LAN port 1 to LAN port 4:
$ swconfig dev switch0 set enable_mirror_rx 1
$ swconfig dev switch0 set enable_mirror_tx 1
$ swconfig dev switch0 set mirror_monitor_port 4
$ swconfig dev switch0 set mirror_source_port 1
Signed-off-by: Colin Leitner <colin.leitner@googlemail.com>
Tested-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 36713
The names are misleading, those are only valid from
AR8236. The AR8216 chip uses different offsets.
Thanks to Jonas Gorski for the report.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34244
