Hardware
--------
MediaTek MT7981 WiSoC
256MB DDR3 RAM
128MB SPI-NAND (XMC XM25QH128C)
MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4 / 5)
UART: 115200 8N1 3.3V
MAC:
LAN MAC: label mac
WAN MAC: label mac + 1
2.4G MAC: label mac
5G MAC: label mac + 1 with LA bit set
Installation
------------
1. Connect to the serial port as described in the "Hardware" section.
2. Power on the device + press reset pin. Keep pressing reset pin to enter the U-Boot shell.
3. Download the OpenWrt initramfs image. Place it on an TFTP server
connected to the Cudy LAN ports. Make sure the server is reachable at
192.168.1.88. Rename the image to "cudy3000s.bin"
4. Download and boot the OpenWrt initramfs image.
$ tftpboot 0x46000000 cudy3000s.bin; bootm 0x46000000
5. Transfer the OpenWrt sysupgrade image to the device using scp.
Install with sysupgrade.
Signed-off-by: David Ignjic <ignjic@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16939
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit faf4b3e0f7)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This commit adds support for two variants of the already supported router
Acer Predator Connect W6: The Acer Predator Connect W6d (W6 without 6 GHz
wifi) and the Acer Connect Vero W6m (W6 without 2.5G eth1 port, usb3 port,
and the 6 on-board gpio RGB LEDs, and with a KTD2026 RGB LED controller
instead of the KTD2061 LED controller of the W6/W6d).
The device tree for the W6m refers to the KTD202x driver suggested in
PR #16860.
Patching target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh
removes the code repetition in (old) lines 121 to 124 on the occasion.
This is the last of four commits into which the original commit was split
to make reviews easier and more targeted.
Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/16861
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 2898d1d126)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
In order to prepare for OpenWrt support other Acer W6 devices and to get
a step further to full hardware support for Acer Predator Connect W6, this
commit
- adjusts the product name ("Acer Predator Connect W6")
- updates gpio LED labels to function/color scheme
- show router status by using first rgb led instead of it's red color only
(blue: booting/failsafe mode; red: sysupgrade; green: running – was: red)
- changes switch/eth1 led configuration to reflect RX/TX activity and speed
(green: full 1Gbps/2.5Gbps speed; amber: lower speed; blink: RX/TX)
- shortens dummy dm-mod.create string in bootargs
- enables W6's i2c interface
This is the third of four commits into which the original commit was split
to make reviews easier and more targeted.
Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/16861
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit d42075dcef)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
In order to prepare OpenWrt support for other Acer W6 devices and to adapt
the procedure to read and set mac addresses which other devices of the same
target are using (instead of needing an additional script and creating an
additional structure in the file system), this commit
- reads device mac addresses from u-boot environment
- avoids the detour via the file system to set the mac addresses
- drops redundant file /lib/preinit/05_extract_factory_data.sh
The idea and the implementation were thankfully taken from PR #16410.
This is the second of four commits into which the original commit was split
to make reviews easier and more targeted.
Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/16861
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit e7aaba2587)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
In order to prepare OpenWrt support for other Acer W6 devices, this commit
moves all device tree components that are used by all Acer W6/W6e/W6d/W6m
routers from mt7986a-acer-predator-w6.dts to mt7986a-acer-w6-common.dtsi
(new file) and includes this dtsi file in mt7986a-acer-predator-w6.dts.
Minor changes had to be made to the device tree in order to improve clarity
and – notably – to reduce the number of dtc warnings:
- replace (obviously wrong) led@<N> gpio led entities by led-<N>
- remove unnecessary (default-state = "off") gpio led statements
- rename entity “memory” to “memory@0”
- add missing #address-cells and #address-size in /soc/mmc@11230000
- add missing #address-cells and #address-size in /soc/pcie@11280000
- introduce symbols “nvmem” and “swport0” in dtsi (referenced in dts)
The changes were checked with `diff -BEZbdtwy --suppress-common-lines ...`
(comparing two dts files created using old and new fdt-1 blobs again), see
https://github.com/openwrt/openwrt/pull/16861/#issuecomment-2455680020 .
This is the first of four commits into which the original commit was split
to make reviews easier and more targeted.
Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/16861
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit ce3b36b3d5)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
TP-Link CPE710-v2 is an outdoor wireless CPE for 5 GHz with one Ethernet
port based on the AP152 reference board. Compared to the CPE710-v1, the
only change observed in hardware is that the mdio address of the ethernet
physical changed from 0x4 to 0x0.
Specifications:
- SoC: QCA9563-AL3A MIPS 74kc @ 775MHz, AHB @ 258MHz
- RAM: 128MiB DDR2 @ 650MHz
- Flash: 16MiB SPI NOR Based on the GD25Q128
- Wi-Fi 5Ghz: ath10k chip (802.11ac for up to 867Mbps on 5GHz wireless
data rate), based on the QCA9896
- Ethernet: one 1GbE port
- 23dBi high-gain directional 2×2 MIMO parabolic antenna
- Power, LAN, WLAN5G Blue LEDs
Flashing instructions:
Flash factory image through stock firmware WEB UI or through TFTP
To get to TFTP recovery just hold reset button while powering on for around
30-40 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP address:192.168.0.254
Signed-off-by: Tim Noack <tim@noack.id>
Link: https://github.com/openwrt/openwrt/pull/16637
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 5572e0196a)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The Zbtlink ZBT-WE2426-B is an indoor dual band WiFi router
with 4 external non detachable antennas and 5 Fast Ethernet ports.
Hardware of ZBT-WE2426-B:
- SoC: MT7628AN
- RAM: 64 MB (Winbond W9751G6K8-25)
- Storage: 8 MB SPI flash (S25FL064K)
- Ethernet: 5x 10/100 Mbps LAN1,LAN2,LAN3,LAN4 & WAN
- Wireless: 2.4GHz: on SoC (802.11b/g/n)
- Wireless: 5GHz: Mediatek MT7612EN (802.11n/ac)
- LEDs: 8x
- Buttons: 1x reset
- USB: 1x 2.0
- MicroSD slot: 1x
- Power: 9 VDC, 1 A
- Uart: GND TX RX PWR - J1 on the PCB
- Board silkscreen: "ZBT-WE2426-C V04" "2018-02-28" "CTT" "13 18"
Backup the stock firmware, settings and calibration data:
This router comes with PandoraBox OpenWrt firmware, so it is
possible to get all MTD partitions using scp.
Installation:
- Using the bootloader web server. Hold the reset button while turning
the power on. Upload the sysupgrade image on http://192.168.1.1.
- Using the sysupgrade command in PandoraBox OpenWrt.
LEDs:
- LAN1,LAN2,LAN3,LAN4,WAN,WLAN2G use GPIO pins of the MT7628AN SoC
(GPIOs 43,42,41,40,39,44)
- WLAN5G uses pin of MT7612EN.
- The POWER LED is directly connected to the VCC. It can be reconnected to
the GPIO 37 of the MT7628AN SoC by resoldering SMD resistor on the PCB.
Buttons:
- The RESET button is connected to the GPIO 38 of the MT7628AN SoC.
MAC addresses as verified by OEM firmware:
use address source
2g *:b0 factory 0x4 (label)
5g *:b1 factory 0x8004
LAN *:b2 factory 0x28
WAN *:b3 factory 0x2e
Signed-off-by: Vaclav Svoboda <svoboda@neng.cz>
Link: https://github.com/openwrt/openwrt/pull/16927
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 3a9752ea02)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
New stm32 target introduces support for stm32mp1 based devices.
For now it includes an initial support of the STM32MP135F-DK device.
The specifications bellow only list supported features.
Specifications
--------------
SOC: STM32MP135FAF7
RAM: 512 MiB
Storage: SD Card
Ethernet: 2x 100 Mbps
Wireless: 2.4GHz Cypress CYW43455 (802.11b/g/n)
LEDs: Heartbeat (Blue)
Buttons: 1x Reset, 1x User (USER2)
USB: 4x 2.0 Type-A
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 851e7f77e4)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
All new routers are shipped with ubi size 112MB since early September.
Bootloader update required (ask vendor , see wiki)
These partitions weren't used:
firmware_backup
zrsave
config2
Signed-off-by: Romanov Danila <pervokur@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16686
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit d8a9669093)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Commit e52c57bb1b renamed all
network ports to match the faceplate of the Gowin 1U Rack
Mount Server and added the br-lan bridge for the eth* ports.
This commit adds the PoE port to the br-lan bridge and a
br-wan bridge for the two SFP ports so that all ports are
part of the default network configuration.
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/16965
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 75af6a0d73)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Popular bpi-r3 pwm fans like this one
https://www.amazon.com/youyeetoo-Barebone-Fan-BPI-R3-Integrated/dp/B0CCCTY8PS
will not work properly with current openwrt-23.05/24.10 firmware.
Trying different pwm setting
echo $value > /sys/devices/platform/pwm-fan/hwmon/hwmon1/pwm1
I found:
pwm1 value fan rotation speed cpu temperature notes
-----------------------------------------------------------------
0 maximal 31.5 Celsius too noisy
40 optimal 35.2 Celsius no noise hearable
95 minimal
above 95 does not rotate 55.5 Celsius
-----------------------------------------------------------------
At the moment we have following cooling levels:
cooling-levels = <255 96 0>;
for cpu-active-high, cpu-active-medium and cpu-active-low modes correspondingly.
Thus only cpu-active-high and cpu-active-low are usable. I think this is wrong.
This patch fixes cpu-active-medium settings for bpi-r3 board.
PS: I know, the patch is not ideal as it can break pwm fan for some users.
There are some peoples that use handmade cooling solutions, but:
* discussed cooler is the only 'official' pwm cooler for bpi-r3
available on the market.
* most peoples will use passive cooling available on the market or
the discussed cooler.
* the pwm-fan dts section was added before the official cooler
appears on the market.
Thus it should not be a lot of harm from this fix.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16974
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 3467ea905b)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Since kernel_oldconfig doesn't work properly with it, I ran that first
and then moved all the config symbols to config-6.6 and found the
differences.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16847
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 22664498eb)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Since kernel_oldconfig doesn't work properly with it, I ran that first
and then moved all the config symbols to config-6.6 and found the
differences.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16847
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit bec8edb6d6)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Since kernel_oldconfig doesn't work properly with it, I ran that first
and then moved all the config symbols to config-6.6 and found the
differences.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16847
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit e9dd6da916)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
CONFIG_FB_INTEL is now visible on x86 since i915 driver is packaged as kmod
now and it stops compilation, so add it to the generic config.
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 57daea682e)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
All ipq807x devices that were using the legacy 'mmc_do_upgrade' eMMC
sysupgrade code were ported to the replacement 'emmc_do_upgrade' code.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16505
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 491121288e)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Note that the old ad-hoc method did not explicitly align backup data
to 64 KiB boundaries.
Also note that the qnap 301w has a 'rootfs_data' partition in the eMMC
that is being ignored by fstools during boot, presumably due to a bug.
This is why the partition is also ignored in the sysupgrade code and
there is no definition of CI_DATAPART="rootfs_data".
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16505
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit fe481c9c47)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Since the start of the Realtek target OpenWrt works with RTL83XX as the
target architecture. Upstream is using MACH_REALTEK_RTL instead. To
simplify further development align that.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16963
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 65964c42f8)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This commit fixes and closes#16313.
Switch the x86 kernel's timer to tickless operation which is
more power efficient since it is not woken up by periodic timer
interrupts when idle. Also add several other options for CPU
idle governors particularly the upstream default for tickless
kernels, CONFIG_CPU_IDLE_GOV_MENU. Without this commit, my AMD
Ryzen 7 5800U can only achieve a minimum core frequency of 1,384
MHz which is over 3x higher than the processor's minimum
frequency of 400 MHz which is accessible with this modification.
In addition to the lower clock rate, I have seen a concomitant
reduction in both idle temps and at-the-wall power consumption.
Summary:
* Idle CPU freqs dropped from 1,384 MHz to 400 Mhz.
* Idle power consumption dropped from 7 W avg to 5 W.
* Idle temps have dropped from 50C on avg to 43C.
There are other well known reasons to switch to a tickless
timer including: reduced interrupt overhead, better use of CPU
resources, and reduced latency to name a few.
Build system: x86/64
Build-tested: x86/64/AMD Cezanne
Run-tested: x86/64/AMD Cezanne
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/16317
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 31111680f6)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
i915 driver requires to load correct firmware to work on latest x86
GPU, it is more reasonable to make it as a kernel module, so that
initramfs is not required, and it can also save some space from the
kernel image comparing being a built-in driver
Signed-off-by: Joe Zheng <joe.zheng@intel.com>
Link: https://github.com/openwrt/openwrt/pull/16276
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 77cfe8fd15)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Add a new utility, `omnia-eeprom`, which can be used to print / set
EEPROM fields on Turris Omnia.
One example when this utility might be useful is if the board
experiences random crashes due to newer versions of the DDR training
algorithm in newer U-Boot. The user can change the DDR speed from 1600K
to 1333H to solve these issues, with
```
omnia-eeprom set ddr_speed 1333H
```
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://github.com/openwrt/openwrt/pull/16264
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 749a43325b)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The GatoNetworks GDSP is a re-branded version of the R5000 5G Industrial
router from Yinghua Technologies.
The re-branded device comes with OpenWrt preinstalled, and an OpenWrt-based
U-Boot bootloader version. While the flash layout has been kept compatible
with the OpenWrt version found on the stock device (see [5]), the image format
changed, making a bootloader upgrade necessary.
Specifications:
SoC: Mediatek MT7981BA
RAM: 256MB
Flash: SPI-NOR 32 MiB (Winbond W25Q256)
WLAN: MT7976CN DBDC AX Wi-Fi
Switch: MT7531AE (4x LAN Gigabit ports, 1x WAN Gigabit port)
5G: Quectel RM520N modem
Watchdog: an external WDT connected to GPIO 6 is present and always running;
the built-in Mediatek watchdog is also present and effective, but
not used at the moment.
This porting has been tested only with 1x 5G modems installed (the device
supports up to two).
Installation:
Installation is possible via sysupgrade both in the stock device and
re-branded version. However, in the former case, updating the bootloader is
required.
OpenWrt-based U-Boot Bootloader installation
--------------------------------------------
The firmware flashed in the re-branded device at manifacturing time will
flash an OpenWrt-based U-Boot bootloader with some extra recovery features
(see [1]) at first boot.
To update the bootloader, you need to install the mtd-rw module and
insmod it:
insmod mtd-rw i_want_a_brick=1
Then update relevant flash partitions:
mtd erase u-boot-env
mtd erase BL2
mtd erase FIP
mtd write openwrt-mediatek-filogic-gatonetworks_gdsp-preloader.bin BL2
mtd write openwrt-mediatek-filogic-gatonetworks_gdsp-bl31-uboot.fip FIP
And reboot, making sure all previous commands ran succesfully.
If something goes wrong, you can recover your device via the mtk_uartboot
tool.
In my testing, it was possible to start the process even without (un)-plugging
the device, may be handy for remote recovery.
Installation from stock device and firmware
-------------------------------------------
To install vanilla OpenWrt in the stock device (R5000 5G Industrial router
from Yinghua Technologies) running the stock vendor firmware, you will need
to update your bootloader as described in previous section. Remember to use
-F (force upgrade) and -n (not keeping settings).
U-Boot Recovery
---------------
This procedure has been tested only with the OpenWrt-based U-boot bootloader.
Assign your system static IP address 192.168.1.1 and start a TFTP server. The
device will look for an initramfs image named
openwrt-mediatek-filogic-gatonetworks_gdsp-initramfs-kernel.bin
(so you may use openwrt/bin/targets/mediatek/filogic as root dir for your
TFTP server).
Power on the device while keeping the reset button pressed, until you see
a TFTP request from 192.168.1.10. Your environment will be restored to it's
default state.
MAC addresses assignment
------------------------
MAC addresses are assigned slightly differently than in stock firmware. In
particular, the 5 GHz Wi-Fi uses 2.4 GHZ MAC + 1, rather than reusing it with
LA bit set as done in stock firmware. This MAC address is allocated to the
device, so it can be used.
The 2.4 GHz Wi-Fi MAC address is the label MAC. LAN MAC is used to set the
special U-Boot environment ethaddr variable.
device MAC address U-Boot env variable factory partition offset
2.4 GHz Wi-Fi :84 wifi_mac 0x4
5.8 GHz Wi-Fi :85 not present not present
WAN :86 wan_mac 0x24
LAN :87 lan_mac 0x2A
Notes
-----
[1]: the OpenWrt-based U-Boot bootloader you will find installed in the
re-branded device is configured to request for the initramfs image via
TFTP for $gdsp_tftp_tries times before trying normal boot from NOR flash.
Setting this U-Boot environment variable to 0x0 will disable the feature,
which is not implemented in this patch.
[2]: the exposed UART port is connected to ttyS1; the ttyS0 console port is
not exposed.
[3]: the provided bootloader environment has no provision for operating on
BL2 and the FIP partitions. This is an intentional choice to make it
(slightly) more difficult to brick the device.
[4]: it seems GPIO 6 is used both for the "SYS" LED and external WDT.
[5] BL2 expects to find FIP payload at a fixed offset, so some constraints
apply.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
(cherry picked from commit b43194e041)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
i2c_add_numbered_adapter is the wrong function to use here. It requires
setting nr to some value, otherwise it behaves the same as
i2c_add_adapter. nr is not set.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16825
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 44824f0b78)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
What seems to be happening is that the kernel requests an ACTIVE_LOW
gpio initially and sets it to high later based on gpios in dts.
This seems to break some devices where the bootloader sets it to high.
Fixes: e612900ae0 ("ramips: mt7621: convert usb power to regulators")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16877
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit a7bc6bf7db)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Edgerouter-X factory images have not built automatically since 19.x due
to images being over 3MB. While it was possible to build custom images
with very stripped down config, this is no longer possible with the size
increases of linux 6.1 and 6.6.
Drop code for generation of factory images, if some dev later wishes to
try custom images they can revert this commit.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Link: https://github.com/openwrt/openwrt/pull/15194
(cherry picked from commit 4d90b79704)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
With the new layout providing 6MB for kernel there will be no issues
with kernel size affecting build of images.
Re-enable image builds for Edgerouter-X and X-SFP.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Tested-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Link: https://github.com/openwrt/openwrt/pull/15194
(cherry picked from commit 71b4842e3b)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Use compat version to indicate that the new layout for larger kernels
is in place. This handled by the patch to ubnt.sh to always select
the kernel1 slot for flashing and as active kernel slot.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Tested-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Link: https://github.com/openwrt/openwrt/pull/15194
(cherry picked from commit 1bdbd511b2)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
With the updated partition layout set in dts, set the KERNEL_SIZE
parameter to 6MB allowing builds of Linux 6.1 and later to fit.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Tested-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Link: https://github.com/openwrt/openwrt/pull/15194
(cherry picked from commit 09a6bffb6e)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Uboot selects which kernel slot to boot based on a flag in the factory
mtd partition. Patch ubnt.sh to ensure always flash to kernel1 slot and
update flag if required.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Tested-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Link: https://github.com/openwrt/openwrt/pull/15194
(cherry picked from commit 5e355f1f90)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The OEM layout for Edgerouter X provides for two 3MB kernel slots.
As of linux 6.1 the kernel images no longer fit and as such
Edgerouter X builds have been disabled in Main.
Revise the layout to make kernel1 slot 6MB and drop kernel2 slot.
This patch applies the required changes to the dts file.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Tested-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Link: https://github.com/openwrt/openwrt/pull/15194
(cherry picked from commit dc51c4355d)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
