Popular bpi-r3 pwm fans like this one
https://www.amazon.com/youyeetoo-Barebone-Fan-BPI-R3-Integrated/dp/B0CCCTY8PS
will not work properly with current openwrt-23.05/24.10 firmware.
Trying different pwm setting
echo $value > /sys/devices/platform/pwm-fan/hwmon/hwmon1/pwm1
I found:
pwm1 value fan rotation speed cpu temperature notes
-----------------------------------------------------------------
0 maximal 31.5 Celsius too noisy
40 optimal 35.2 Celsius no noise hearable
95 minimal
above 95 does not rotate 55.5 Celsius
-----------------------------------------------------------------
At the moment we have following cooling levels:
cooling-levels = <255 96 0>;
for cpu-active-high, cpu-active-medium and cpu-active-low modes correspondingly.
Thus only cpu-active-high and cpu-active-low are usable. I think this is wrong.
This patch fixes cpu-active-medium settings for bpi-r3 board.
PS: I know, the patch is not ideal as it can break pwm fan for some users.
There are some peoples that use handmade cooling solutions, but:
* discussed cooler is the only 'official' pwm cooler for bpi-r3
available on the market.
* most peoples will use passive cooling available on the market or
the discussed cooler.
* the pwm-fan dts section was added before the official cooler
appears on the market.
Thus it should not be a lot of harm from this fix.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16974
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 3467ea905b)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Since kernel_oldconfig doesn't work properly with it, I ran that first
and then moved all the config symbols to config-6.6 and found the
differences.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16847
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 22664498eb)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Since kernel_oldconfig doesn't work properly with it, I ran that first
and then moved all the config symbols to config-6.6 and found the
differences.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16847
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit bec8edb6d6)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Since kernel_oldconfig doesn't work properly with it, I ran that first
and then moved all the config symbols to config-6.6 and found the
differences.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16847
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit e9dd6da916)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
CONFIG_FB_INTEL is now visible on x86 since i915 driver is packaged as kmod
now and it stops compilation, so add it to the generic config.
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 57daea682e)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
All ipq807x devices that were using the legacy 'mmc_do_upgrade' eMMC
sysupgrade code were ported to the replacement 'emmc_do_upgrade' code.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16505
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 491121288e)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Note that the old ad-hoc method did not explicitly align backup data
to 64 KiB boundaries.
Also note that the qnap 301w has a 'rootfs_data' partition in the eMMC
that is being ignored by fstools during boot, presumably due to a bug.
This is why the partition is also ignored in the sysupgrade code and
there is no definition of CI_DATAPART="rootfs_data".
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16505
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit fe481c9c47)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Since the start of the Realtek target OpenWrt works with RTL83XX as the
target architecture. Upstream is using MACH_REALTEK_RTL instead. To
simplify further development align that.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16963
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 65964c42f8)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This commit fixes and closes#16313.
Switch the x86 kernel's timer to tickless operation which is
more power efficient since it is not woken up by periodic timer
interrupts when idle. Also add several other options for CPU
idle governors particularly the upstream default for tickless
kernels, CONFIG_CPU_IDLE_GOV_MENU. Without this commit, my AMD
Ryzen 7 5800U can only achieve a minimum core frequency of 1,384
MHz which is over 3x higher than the processor's minimum
frequency of 400 MHz which is accessible with this modification.
In addition to the lower clock rate, I have seen a concomitant
reduction in both idle temps and at-the-wall power consumption.
Summary:
* Idle CPU freqs dropped from 1,384 MHz to 400 Mhz.
* Idle power consumption dropped from 7 W avg to 5 W.
* Idle temps have dropped from 50C on avg to 43C.
There are other well known reasons to switch to a tickless
timer including: reduced interrupt overhead, better use of CPU
resources, and reduced latency to name a few.
Build system: x86/64
Build-tested: x86/64/AMD Cezanne
Run-tested: x86/64/AMD Cezanne
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/16317
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 31111680f6)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
i915 driver requires to load correct firmware to work on latest x86
GPU, it is more reasonable to make it as a kernel module, so that
initramfs is not required, and it can also save some space from the
kernel image comparing being a built-in driver
Signed-off-by: Joe Zheng <joe.zheng@intel.com>
Link: https://github.com/openwrt/openwrt/pull/16276
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 77cfe8fd15)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Add a new utility, `omnia-eeprom`, which can be used to print / set
EEPROM fields on Turris Omnia.
One example when this utility might be useful is if the board
experiences random crashes due to newer versions of the DDR training
algorithm in newer U-Boot. The user can change the DDR speed from 1600K
to 1333H to solve these issues, with
```
omnia-eeprom set ddr_speed 1333H
```
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://github.com/openwrt/openwrt/pull/16264
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 749a43325b)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The GatoNetworks GDSP is a re-branded version of the R5000 5G Industrial
router from Yinghua Technologies.
The re-branded device comes with OpenWrt preinstalled, and an OpenWrt-based
U-Boot bootloader version. While the flash layout has been kept compatible
with the OpenWrt version found on the stock device (see [5]), the image format
changed, making a bootloader upgrade necessary.
Specifications:
SoC: Mediatek MT7981BA
RAM: 256MB
Flash: SPI-NOR 32 MiB (Winbond W25Q256)
WLAN: MT7976CN DBDC AX Wi-Fi
Switch: MT7531AE (4x LAN Gigabit ports, 1x WAN Gigabit port)
5G: Quectel RM520N modem
Watchdog: an external WDT connected to GPIO 6 is present and always running;
the built-in Mediatek watchdog is also present and effective, but
not used at the moment.
This porting has been tested only with 1x 5G modems installed (the device
supports up to two).
Installation:
Installation is possible via sysupgrade both in the stock device and
re-branded version. However, in the former case, updating the bootloader is
required.
OpenWrt-based U-Boot Bootloader installation
--------------------------------------------
The firmware flashed in the re-branded device at manifacturing time will
flash an OpenWrt-based U-Boot bootloader with some extra recovery features
(see [1]) at first boot.
To update the bootloader, you need to install the mtd-rw module and
insmod it:
insmod mtd-rw i_want_a_brick=1
Then update relevant flash partitions:
mtd erase u-boot-env
mtd erase BL2
mtd erase FIP
mtd write openwrt-mediatek-filogic-gatonetworks_gdsp-preloader.bin BL2
mtd write openwrt-mediatek-filogic-gatonetworks_gdsp-bl31-uboot.fip FIP
And reboot, making sure all previous commands ran succesfully.
If something goes wrong, you can recover your device via the mtk_uartboot
tool.
In my testing, it was possible to start the process even without (un)-plugging
the device, may be handy for remote recovery.
Installation from stock device and firmware
-------------------------------------------
To install vanilla OpenWrt in the stock device (R5000 5G Industrial router
from Yinghua Technologies) running the stock vendor firmware, you will need
to update your bootloader as described in previous section. Remember to use
-F (force upgrade) and -n (not keeping settings).
U-Boot Recovery
---------------
This procedure has been tested only with the OpenWrt-based U-boot bootloader.
Assign your system static IP address 192.168.1.1 and start a TFTP server. The
device will look for an initramfs image named
openwrt-mediatek-filogic-gatonetworks_gdsp-initramfs-kernel.bin
(so you may use openwrt/bin/targets/mediatek/filogic as root dir for your
TFTP server).
Power on the device while keeping the reset button pressed, until you see
a TFTP request from 192.168.1.10. Your environment will be restored to it's
default state.
MAC addresses assignment
------------------------
MAC addresses are assigned slightly differently than in stock firmware. In
particular, the 5 GHz Wi-Fi uses 2.4 GHZ MAC + 1, rather than reusing it with
LA bit set as done in stock firmware. This MAC address is allocated to the
device, so it can be used.
The 2.4 GHz Wi-Fi MAC address is the label MAC. LAN MAC is used to set the
special U-Boot environment ethaddr variable.
device MAC address U-Boot env variable factory partition offset
2.4 GHz Wi-Fi :84 wifi_mac 0x4
5.8 GHz Wi-Fi :85 not present not present
WAN :86 wan_mac 0x24
LAN :87 lan_mac 0x2A
Notes
-----
[1]: the OpenWrt-based U-Boot bootloader you will find installed in the
re-branded device is configured to request for the initramfs image via
TFTP for $gdsp_tftp_tries times before trying normal boot from NOR flash.
Setting this U-Boot environment variable to 0x0 will disable the feature,
which is not implemented in this patch.
[2]: the exposed UART port is connected to ttyS1; the ttyS0 console port is
not exposed.
[3]: the provided bootloader environment has no provision for operating on
BL2 and the FIP partitions. This is an intentional choice to make it
(slightly) more difficult to brick the device.
[4]: it seems GPIO 6 is used both for the "SYS" LED and external WDT.
[5] BL2 expects to find FIP payload at a fixed offset, so some constraints
apply.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
(cherry picked from commit b43194e041)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
i2c_add_numbered_adapter is the wrong function to use here. It requires
setting nr to some value, otherwise it behaves the same as
i2c_add_adapter. nr is not set.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16825
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 44824f0b78)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
What seems to be happening is that the kernel requests an ACTIVE_LOW
gpio initially and sets it to high later based on gpios in dts.
This seems to break some devices where the bootloader sets it to high.
Fixes: e612900ae0 ("ramips: mt7621: convert usb power to regulators")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16877
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit a7bc6bf7db)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Edgerouter-X factory images have not built automatically since 19.x due
to images being over 3MB. While it was possible to build custom images
with very stripped down config, this is no longer possible with the size
increases of linux 6.1 and 6.6.
Drop code for generation of factory images, if some dev later wishes to
try custom images they can revert this commit.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Link: https://github.com/openwrt/openwrt/pull/15194
(cherry picked from commit 4d90b79704)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
With the new layout providing 6MB for kernel there will be no issues
with kernel size affecting build of images.
Re-enable image builds for Edgerouter-X and X-SFP.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Tested-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Link: https://github.com/openwrt/openwrt/pull/15194
(cherry picked from commit 71b4842e3b)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Use compat version to indicate that the new layout for larger kernels
is in place. This handled by the patch to ubnt.sh to always select
the kernel1 slot for flashing and as active kernel slot.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Tested-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Link: https://github.com/openwrt/openwrt/pull/15194
(cherry picked from commit 1bdbd511b2)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
With the updated partition layout set in dts, set the KERNEL_SIZE
parameter to 6MB allowing builds of Linux 6.1 and later to fit.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Tested-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Link: https://github.com/openwrt/openwrt/pull/15194
(cherry picked from commit 09a6bffb6e)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Uboot selects which kernel slot to boot based on a flag in the factory
mtd partition. Patch ubnt.sh to ensure always flash to kernel1 slot and
update flag if required.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Tested-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Link: https://github.com/openwrt/openwrt/pull/15194
(cherry picked from commit 5e355f1f90)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The OEM layout for Edgerouter X provides for two 3MB kernel slots.
As of linux 6.1 the kernel images no longer fit and as such
Edgerouter X builds have been disabled in Main.
Revise the layout to make kernel1 slot 6MB and drop kernel2 slot.
This patch applies the required changes to the dts file.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Tested-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Link: https://github.com/openwrt/openwrt/pull/15194
(cherry picked from commit dc51c4355d)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Edgerouter X currently has its eth1 port on the switch missing since there
is a naming conflict currently.
So, as the root cause is mixing kernel support for DSA interfaces having
predictable names set via "label" property vs others having it assigned
dynamically lets avoid the conflict by using our own custom property as
suggested upstream [1].
So, add support via "openwrt,netdev-name" property and use it on ERX.
Fixes: 2a25c6ace8 ("ramips: get rid of downstream network device label patch")
Fixes: #15643
Link: https://github.com/openwrt/openwrt/pull/17062
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 5695267847)
The label-mac does not match the one assigned to the ethernet interface.
Use the mac-address assigned to the wifi interface instead, as it
matches the one found on the device label.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit b8b658bc0d)
Trying to use 'package_whatdepends' feature of the ImageBuilder with OPKG
will currently fail as OPKG does not support "list --depends" call at all,
it seems that this is a mixup from the original APK support commit.
So, lets restore 'package_whatdepends' support for OPKG by calling
"whatdepends -A" instead as we used to before APK support.
Fixes: d788ab376f ("build: add APK package build capabilities")
Link: https://github.com/openwrt/openwrt/pull/17022
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 52519a59a8)
The original set of stock partitions was kept in the TR4400 v2 port,
with the same partition numbers but their names prefixed with 'stock_'.
This allowed scripts (installation, back to stock, etc) to run on both
stock and OpenWrt firmware. But this triggers warnings in the device
tree compiler, as partitions of the old and new schemes overlap.
This commit fixes the dtc warnings by deleting the stock partitions,
also renumbering some of the remaining MTD partitions in the process.
Additionally, the 'fw_env' partition is set to read-only.
These changes can break existing scripts as well as user configurations
that utilize the 'extra' partition. Users wanting to run old scripts can
do so by reverting to the 23.05 series releases.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16958
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 8ec35a2a15)
The broadcom PHY driver only has to depend upon PTP_1588_CLOCK_OPTIONAL
if NETWORK_PHY_TIMESTAMPING is enabled. The PTP functionality is stubbed
in this case.
Reflect this circumstance in the dependence condition. This allows to
build the driver as a built-in module even if PTP is built as a module.
This is required to include the broadcom PHY module regardless of the
built-setting of the PTP subsystem. On ath79 (and probably more)
targets with Broadcom PHY, Gigabit operation is currently broken as the
PHY driver is only built as a module in case all kernel-packages are
built. Due to this circumstance, affected devices fall back to using the
generic PHY driver.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit cbce32e30c)
Sync patch with upstream version and tag them.
Minor changes done to Pinctrl patch to support older kernel.
Patch automatically refreshed with make target/linux/refresh.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit a5d23e3aee)
The Sophos AP15C uses the same hardware as the AP15, but has a reset button.
Based on:
commit 6f1efb2898 ("ath79: add support for Sophos AP100/AP55 family")
author Andrew Powers-Holmes <andrew@omnom.net>
Fri, 3 Sep 2021 15:53:57 +0200 (23:53 +1000)
committer Hauke Mehrtens <hauke@hauke-m.de>
Sat, 16 Apr 2022 16:59:29 +0200 (16:59 +0200)
Unique to AP15C:
- Reset button
- External RJ45 serial console port
Flashing instructions:
This firmware can be flashed either via a compatible Sophos SG or XG
firewall appliance, which does not require disassembling the device, or via
the U-Boot console available on the internal UART header.
To flash via XG appliance:
- Register on Sophos' website for a no-cost Home Use XG firewall license
- Download and install the XG software on a compatible PC or virtual
machine, complete initial appliance setup, and enable SSH console access
- Connect the target AP device to the XG appliance's LAN interface
- Approve the AP from the XG Web UI and wait until it shows as Active
(this can take 3-5 minutes)
- Connect to the XG appliance over SSH and access the Advanced Console
(Menu option 5, then menu option 3)
- Run `sudo awetool` and select the menu option to connect to an AP via
SSH. When prompted to enable SSH on the target AP, select Yes.
- Wait 2-3 minutes, then select the AP from the awetool menu again. This
will connect you to a root shell on the target AP.
- Copy the firmware to /tmp/openwrt.bin on the target AP via SCP/TFTP/etc
- Run `mtd -r write /tmp/openwrt.bin astaro_image`
- When complete, the access point will reboot to OpenWRT.
To flash via U-Boot serial console:
- Configure a TFTP server on your PC, and set IP address 192.168.99.8 with
netmask 255.255.255.0
- Copy the firmware .bin to the TFTP server and rename to 'uImage_AP15C'
- Open the target AP's enclosure and locate the 4-pin 3.3V UART header [4]
- Connect the AP ethernet to your PC's ethernet port
- Connect a terminal to the UART at 115200 8/N/1 as usual
- Power on the AP and press a key to cancel autoboot when prompted
- Run the following commands at the U-Boot console:
- `tftpboot`
- `cp.b $fileaddr 0x9f070000 $filesize`
- `boot`
- The access point will boot to OpenWRT.
Signed-off-by: David Lutz <kpanic@hirnduenger.de>
(cherry picked from commit a7abc7ec3b)
This reverts commit e1043a746a, that
attempts to nest partitions that overlap but are not nested. This
causes the 'ubi' partition to be truncated, making rootfs inaccessible
and bricking the device.
Also, had this commit worked, it would have renumbered MTD partitions
in a way that would have broken documented scripts for installation and
update of main and recovery OSes, making backups, return to stock, etc,
and broken user configurations that put the 'extra' partition to use.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16944
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 0e59eaa796)
The last "syscfg" partition of the OEM firmware turns out to be a
UBIFS used to store user data, just as the "rootfs_data" of OpenWrt,
so it should be reasonable to absorb it into the "ubi" partition.
Factory installations via either OEM firmware or tftp, or by forcibly
flashing factory image to mtd5 (firmware) partition with mtd tool are
confirmed working, but the UBI remaining inside "syscfg" partition
could break upgrade. Fortunately, installing kmod-mtd-rw and erasing
"syscfg" partition before upgrade is confirmed working, in which case,
"ubi" will automatically expand to the blank space once occupied by
the former mtd8 (syscfg), with the total block number increased, but
the UBIFS for rootfs_data will not automatically claim the newly
available space (since it is created when mtd8 still exists, and
sysupgrade does not set "autoresize" flag to rootfs_data). These space
will be claimed during the next upgrade, when rootfs_data is removed
and created again.
Fixes: 50f727b773 ("ath79: add support for Linksys EA4500 v3")
Signed-off-by: Edward Chow <equu@openmail.cc>
Link: https://github.com/openwrt/openwrt/pull/14791
Signed-off-by: Robert Marko <robimarko@gmail.com>
Mass production units will get 16 assigned MAC addresses. This allows each phy
to spawn up to 7 VAPs which will each have unique MAC without needing the
private bit.
Signed-off-by: John Crispin <john@phrozen.org>
Mass production units will get 16 assigned MAC addresses. This allows each phy
to spawn up to 7 VAPs which will each have unique MAC without needing the
private bit.
Signed-off-by: John Crispin <john@phrozen.org>
The mediatek target requires refreshing after recent additions.
Fixes: cfe8e6e75f ("mediatek: add support for Realtek RTL8261n 10G PHYs")
Fixes: ddfae94a14 ("mediatek: add support for swapping the polarity on usxgmii interfaces")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Assign pwm function of PWM0 pin to the pwm-fan.
This is mostly just cosmetics as it basically reflects the default
setting of that pin.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add additionals possible pinctrl group for pwm2~7 on pins
pin 4 (GPIO_A) pwm7
pin 58 (JTAG_JTDI) pwm2
pin 59 (JTAG_JTDO) pwm3
pin 60 (JTAG_JTMS) pwm4
pin 61 (JTAG_JTCLK) pwm5
pin 62 (JTAG_JTRST_N) pwm6
They can be useful e.g. on the BPi-R4 as in that way pwm2~6 can be exposed
on the 26-pin header (pwm6 always, pwm2~5 instead of the full UART).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
A factory image for DNA EX400 depends on an initramfs image and they
were explicitly removed from the imagebuilder recently. Now the factory
image creation fails miserably and it also affects custom image creation
with the firmware selector.
Add the initramfs kernel to the staging so that it's shipped with the
imagebuilder. Also remove a image build target added solely for DNA EX400.
Tested by creating a factory and syspupgrade images locally with
the imagebuilder and verified their functionality.
Related work
c85348d9ab ("imagebuilder: remove initramfs image files")
Fixes: fea2264d9f ("ramips: mt7621: Add DNA Valokuitu Plus EX400")
Signed-off-by: Mauri Sandberg <maukka@ext.kapsi.fi>
---
v4: use append-image-stage, remove Build/kernel-initramfs-bin
v3: adjust commit subject
v2: remove fix for inconsistent line ending elsewhere in the file
Link: https://github.com/openwrt/openwrt/pull/16659
Signed-off-by: Robert Marko <robimarko@gmail.com>
Upstream stable is slow at picking this up and several systems
are regressing. Add the patch locally in OpenWrt.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Specifying GPIO_ACTIVE_HIGH on the GPIO for the voltage regulator doesn't
suffice. The regulator itself requires enable-active-high to be set.
Fixes: #16292
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
Link: https://github.com/openwrt/openwrt/pull/16839
Signed-off-by: Robert Marko <robimarko@gmail.com>
The clocks for SPI busses were named wrongly which resulted in the
spi-mt65xx driver not requesting them. This has apparently been
worked around by marking the clocks required for SPI0 which is used
for SPI-NOR and SPI-NAND flash chips as critical.
Fix the device tree for all 3 generic SPI host controllers and no
longer mark clocks as critical.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 2b173ab730)
Fix in commit 25eead21c5 ("ath79: fix 5GHz on QCA9886 variant of ZTE MF286")
was incomplete. A user of such variant popped up, and in the boot log
after installation, we discovered that QCA9886 expects different
pre-calibration data size, than the older QCA9880 variant:
ath10k_pci 0000:00:00.0: qca9888 hw2.0 target 0x01000000 chip_id 0x00000000 sub 0000:0000
ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
ath10k_pci 0000:00:00.0: firmware ver 10.4b-ct-9888-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 59e741e7
ath10k_pci 0000:00:00.0: invalid calibration data length in nvmem-cell 'pre-calibration': 2116 != 12064
ath10k_pci 0000:00:00.0: Loading BDF type 0
ath10k_pci 0000:00:00.0: failed to fetch board data for bus=pci,vendor=168c,device=0056,subsystem-vendor=0000,subsystem-device=0000 from ath10k/QCA9888/hw2.0/board-2.bin
ath10k_pci 0000:00:00.0: failed to fetch board-2.bin or board.bin from ath10k/QCA9888/hw2.0
ath10k_pci 0000:00:00.0: failed to fetch board file: -12
ath10k_pci 0000:00:00.0: could not probe fw (-12)
Explicitly define a pre-calibration nvmem-cell for this variant, and use
it instead of the calibration one, which is shorter.
Fixes: 25eead21c5 ("ath79: fix 5GHz on QCA9886 variant of ZTE MF286")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16809
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The patches were generated from the RPi repo with the following command:
git format-patch v6.6.58..rpi-6.6.y
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
It should be debounce-interval, as with the others.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16802
Signed-off-by: Robert Marko <robimarko@gmail.com>
This reverts commit ec8f647d16, as with the
current kernel version, the change actually causes the same bug it once
may have fixed -- that is, the leds are now again reversed.
I suspect this was due to a switch to a newer kernel version between when
the patch was submitted and now reversing the order of the interfaces, so
that eth0 / the LAN interface is also the interface used for PoE, and eth1
/ the WAN interface is the non-PoE interface.
Signed-off-by: Rafal Boni <rafal.boni@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16779
Signed-off-by: Robert Marko <robimarko@gmail.com>
Those packages were not copied due to OPKG using an underscore while APK
uses dashes. Remove that char to copy kernel/libc for either APK/OPKG.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Drop removal of firewall4 package for I2SE Duckbill device.
With OPKG the firewall4 package was installed anyway as it's a
dependency of luci-app-firewall and was silently installed again later
in such condition. Drop it to fix support for APK.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop removal of firewall4 package for Synology DS213j device.
With OPKG the firewall4 package was installed anyway as it's a
dependency of luci-app-firewall and was silently installed again later
in such condition. Drop it to fix support for APK.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
RouterBOOT v7 on NOR devices no longer accepts the YAFFS kernel ELF
method of booting. It will accept an NPK image named bootimage.
Adjust mtdsplit_minor to accept this second possible boot file name.
Use the conservative value of 127 for YAFFS max name length (used when
YAFFS compiled with unicode support) vs 255.
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
Acked-by: Thibaut VARENE <hacks@slashdirt.org>
Link: https://github.com/openwrt/openwrt/pull/16780
Signed-off-by: Robert Marko <robimarko@gmail.com>
Introduced with Linux 6.7, in commit:
5c2f7727d437 ("mtd: mtdpart: check for subpartitions parsing result"),
when a parser returns an error, this will be passed up, and
consequently, all parent mtd partitions get torn down.
Adjust the MiNOR mtdsplit driver to only return an error if there is a
critical problem in reading from the mtd device or allocating memory.
Otherwise return 0 to indicate that no partitions were found.
Also add logging to indicate what went wrong.
This mtdsplit parser makes a very limited check of the first YAFFS
header. For example, this will not match expectations when initially booting
an initramfs image with OEM on MTD.
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
Acked-by: Thibaut VARENE <hacks@slashdirt.org>
Link: https://github.com/openwrt/openwrt/pull/16780
Signed-off-by: Robert Marko <robimarko@gmail.com>
It does the same thing minus a few dmesg prints.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16788
Signed-off-by: Robert Marko <robimarko@gmail.com>
The WiFi chips are actually on PCIe1 and PCIe2, PCIe0 is empty. Fix the
assignment so that WiFi works properly again.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Link: https://github.com/openwrt/openwrt/pull/16807
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Drop limitation on depending on only armv8 for armsr target as those
module should support both 32 and 64 bits systems.
Only thunderx-net actually require 64 bit systems.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop fmc and fmc-eth-config package as they were never actually
submitted to openwrt mainline and they don't exist around.
They are probably part of NXP SDK and were added due to copy-paste
errors.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add the '~' prefix to package that needs to skip installation as they
are meta-package just to download and compile firmware package for the
final firmware.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop kmod-i2c-ralink from ASUS RP-AC56 as it was wrongly added. Such
kmod is not supported on mt7621 as i2c is handled by the mediatek driver
and not bay the ralink downstream one.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix wrong package device list that is trying to remove deprecated
packages. Replace with new variant where possible.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop ipq-wifi-teltonika_rutx from Teltonika RUTX50, the board file was
merged upstream but the ipq package was never dropped from
DEVICE_PACKAGES list.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop kmod-ledtrig-default-on and kmod-ledtrig-netdev as the kmod were
dropped and are now enabled by default.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Complete support for local signing keys for APK.
A local key will be always generated, mkndx is always called with
--allow-untrusted as it needs to replace the sign key with the new local
one.
With CONFIG_SIGNATURE_CHECK the local index is signed with the local
key. Local public key is added with the ADD_LOCAL_KEY option.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
ImageBuilder compiled by buildbot doesn't have any package in the
packages directory. Package needs to be downloaded instead.
This works by calling update to the package manage to download the
remove index and download the file.
Fix missing support for this with APK, by configuring the
--repositories-file option and calling the APK update.
Also move the apk add --initdb to package_index.
If CONFIG_SIGNATURE_CHECK is not enabled, the signature is not checked.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Correctly export PACKAGE_DIR and PACKAGE_DIR_ALL so that they won't be
reset on internal call of rules.mk
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This GPIO is pulled down by the onboard MCU when the power button
is pressed for 5 seconds, indicating a user-initiated shutdown.
Refresh patches at the same time.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Although Zyxel XGS1210 devices are not yet officially supported there
are several patches floating around to enable them. This is a very imporant
one because it fixes a SMI misconfiguration. In the known DTS the SFP+
port settings are set as follows.
phy26: ethernet-phy@26 {
compatible = "ethernet-phy-ieee802.3-c45";
phy-is-integrated;
reg = <26>;
sds = < 8 >;
};
phy27: ethernet-phy@27 {
compatible = "ethernet-phy-ieee802.3-c45";
phy-is-integrated;
reg = <27>;
sds = < 9 >;
};
So these are PHYs linked to an internal SerDes. During initialization
rtl838x_mdio_init() generates smi_bus=0 & smi_addr=27/28 for these ports.
Although this seems like a valid configuration integrated PHYs attached
to an SerDes do not have an SMI bus. Later on the mdio reset wrongly feeds
the SMI registers and as a result the PHYs on SMI bus 0 do not work.
Without patch (loaded with rtk network on & initramfs):
...
mdio_bus mdio-bus: MDIO device at address 0 is missing.
mdio_bus mdio-bus: MDIO device at address 1 is missing.
mdio_bus mdio-bus: MDIO device at address 2 is missing.
mdio_bus mdio-bus: MDIO device at address 3 is missing.
mdio_bus mdio-bus: MDIO device at address 4 is missing.
mdio_bus mdio-bus: MDIO device at address 5 is missing.
mdio_bus mdio-bus: MDIO device at address 6 is missing.
mdio_bus mdio-bus: MDIO device at address 7 is missing.
...
rtl83xx-switch ... : no phy at 0
rtl83xx-switch ... : failed to connect to PHY: -ENODEV
rtl83xx-switch ... : error -19 setting up PHY for tree 0, switch 0, port 0
rtl83xx-switch ... : no phy at 1
rtl83xx-switch ... : failed to connect to PHY: -ENODEV
rtl83xx-switch ... : error -19 setting up PHY for tree 0, switch 0, port 1
...
With patch (loaded with rtk network on & initramfs):
...
rtl83xx-switch ... : PHY [mdio-bus:00] driver [REALTEK RTL8218D] (irq=POLL)
rtl83xx-switch ... : PHY [mdio-bus:01] driver [REALTEK RTL8218D] (irq=POLL)
...
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16457
Signed-off-by: Robert Marko <robimarko@gmail.com>
The RTL930x have only 4 SMI busses (0-3) and the XGS1250 SFP port ist
directly managed. Remove the wrong configuration in the dts.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16457
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently RTL8218D detection works for a range of devices. That can lead to
false positives. E.g. RTL8218B or RTL8214FC are covered by the detection mask
as well. That is wrong. Nail detection down to the real RTL8218D phy id.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16457
Signed-off-by: Robert Marko <robimarko@gmail.com>
The detection of the RTL8214C is a little complicated. Make it easier.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16457
Signed-off-by: Robert Marko <robimarko@gmail.com>
Three PHYs share the same identifier. Until now we simply assume
the type depending of the bus address it is attached to. Make it
better and check the chip mode register instead.
The kernel will either detect by id/mask or by match_phy_device().
Remove the unneeded settings.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16457
Signed-off-by: Robert Marko <robimarko@gmail.com>
The number of phy pages differ between RTL838X and RTL839X. Make that
clear and adapt the existing defines.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16457
Signed-off-by: Robert Marko <robimarko@gmail.com>
According to the specs the RTL839x provides up to 8192 phy pages.
Especially the "raw" page 8191 is used for different initialization
tasks. Increase the limit.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16457
Signed-off-by: Robert Marko <robimarko@gmail.com>
