[juhosg: remove ath9k from the the profile package list, build WPE72
image with the Default profile as well]
Signed-off-by: Johnathan Boyce <jon.boyce@globalreach.eu.com>
SVN-Revision: 29914
This patch adds support for Compex WPE72 bare board and Compex WPE72NX
Indoor Access Point.
[juhosg: add support to 3.2 as well]
Signed-off-by: Johnathan Boyce <jon.boyce@globalreach.eu.com>
SVN-Revision: 29912
This patch adds support for the Sitecom WL-341 v3 and other Sercomm
IP1006RRv2 based boards for sysupgrade support and for the initial
flash through pushbutton initiated recovery mode with the special
partition table and fixes for the quirks and things required by the
modified bootloader.
There is a known bug, Wi-Fi is not working on my board probably
because of the lack of RAM (the board only has 16MiB ram -- half of
the normal amount for non rebadged versions, but there is an empty
slot for another ram chip,) but I don't know for sure. The driver
loads but hostapd fails to load so I think it's not related to the
specific device except for the lack of RAM.
Moreover, only 7 of the 11 onboard leds are confirmed working, it
seems that one of the others is always on and the remaining ones are
connected to the wireless card leds already recognized by OpenWrt
[juhosg: reordered some parts in order to keep things sorted
alphabetically]
Signed-off-by: Marco Antonio Mauro <marcus90@gmail.com>
SVN-Revision: 29910
Hi!
On Mon, Nov 14, 2011 at 03:01:34PM +0100, Daniel Golle wrote:
> The driver works quite nice and stable for me using a RaLink Rt5370 USB device.
>
> Signed-off-by: Daniel Golle <dgolle@allnet.de>
>
> Index: package/mac80211/Makefile
> ===================================================================
> --- package/mac80211/Makefile (revision 29114)
> +++ package/mac80211/Makefile (working copy)
> @@ -1147,6 +1147,7 @@
> CONFIG_RT2800_LIB=$(if $(CONFIG_PACKAGE_kmod-rt2800-lib),m) \
> CONFIG_RT2800PCI=$(if $(CONFIG_PACKAGE_kmod-rt2800-pci),m) \
> CONFIG_RT2800USB=$(if $(CONFIG_PACKAGE_kmod-rt2800-usb),m) \
> + CONFIG_RT2800USB_RT53XX=$(if $(CONFIG_PACKAGE_kmod-rt2800-usb),y) \
> CONFIG_RTL8180=$(if $(CONFIG_PACKAGE_kmod-rtl8180),m) \
> CONFIG_RTL8187=$(if $(CONFIG_PACKAGE_kmod-rtl8187),m) \
> CONFIG_RTL8192CE= \
Aparently this was wrong, CONFIG_RT2800USB_RT53XX is supposed to live in
BUILDARGS rather than MAKE_OPTS to actually get support for the Rt5370.
Thanks to actmnophn for the hint!
This reverts changeset 29116 and adds it to the right section in the Makefile.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 29906
This patch fixes the board detection of the TL-MR3020.
The LED behaviour has also been modified:
* The WPS LED is the diag LED now.
* A netdev trigger for the LAN LED has been added.
The profile of the TL-MR3020 has been updated because the needed package
"kmod-ledtrig-usbdev" was missing which resulted in a non-working usbdev
trigger for the 3G/USB LED.
[juhosg: the board name changes has been removed, and the kernel files
has been changed instead.]
Signed-off-by: Christian Cier-Zniewski <c.cier@gmx.de>
SVN-Revision: 29905
This patch fixes the GPIO polarity for the button and the sliding
switch. The buttons are not active low. "Pressed" and "Released"
events are wrong without the patch.
Signed-off-by: Christian Cier-Zniewski <c.cier@gmx.de>
SVN-Revision: 29904
