Since the wireless LED was used for boot and set up with a DT
trigger, the WiFi indication hasn't worked on ath79 at all.
In addition, a look into the manual revealed that the OEM
configuration is as follows:
LED 1 (green): power
LED 2 (green): configurable
LED 3 (red): wireless
So, let's just keep the WiFi trigger and convert the rest to its
"intended" use.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
zstd with its default settings (compression level -3) compresses better
than bzip2 -9 (which is the default setting), and is an order of magnitude
faster.
I made the following measurements for the most common compression tools
(all standard Debian Buster versions, default flags unless noted
otherwise), using the debug information of a large x86-64 kernel with
ALL_KMODS:
* kernel-debug.tar: 376M
* kernel-debug.tar.gz: 101M, compressed in ~12s
* kernel-debug.tar.bz2: 91M, compressed in ~15s
* kernel-debug.tar.xz: 57M, compressed in ~101s
* kernel-debug.tar.zst: 86M, compressed in ~1s
With zstd, there is still some room for improvement by increasing the
compression, but the slight increase in compression ratio
(22.83% -> 19.46%) does not justify the significant increase in
compression time (about 5 times on my machine) in my opinion.
Note that multithreaded compression (-T argument) does not affect
reproducibility with zstd.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
We currently support three kernel versions on this target, let's
just get rid of the oldest one.
Cc: Rafał Miłecki <rafal@milecki.pl>
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
We currently support three kernel versions on this target, let's
just get rid of the oldest one.
Cc: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
From: Rui Salvaterra <rsalvaterra@gmail.com>
Date: Mon, 25 May 2020 14:49:07 +0100
Subject: [PATCH] rt2800: enable MFP support unconditionally
This gives us WPA3 support out of the box without having to manually disable
hardware crypto. The driver will fall back to software crypto if the connection
requires management frame protection.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
GPS time without date was previously used to set system date:
Tue Oct 10 11:48:21 2000 user.info kernel: [ 108.786639] ugps: system time differs from GPS time by more than 5 seconds. Using 2000-10-10T10:48:21 UTC as the new time
Tue Oct 10 11:49:27 2000 user.info kernel: [ 174.794699] ugps: system time differs from GPS time by more than 5 seconds. Using 2020-05-26T10:49:27 UTC as the new time
Fix this by ignoring incomplete dates and wait for complete time
information before adjusting system date/time.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The -O option for the tplink-v1-header was missing for the TP-Link
TL-WR902AC v1, while safeloader and MTDPARTS where set up with a
single firmware partition.
This led to bootloops after using sysupgrade.
Fixes: FS#3118
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Also ensure that the error message is actually printed to stderr and that
the rule generation is aborted if an interface cannot be resolved.
Ref: https://github.com/openwrt/luci/issues/3975
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Also removes random module and switches to new bcm2711 thermal driver.
Boot tested on RPi 4B v1.1 4G.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
disable_vht parameter needs to be set when using wpa_supplicant NOHT/HT* modes.
Signed-off-by: Enrique Rodríguez Valencia <enrique.rodriguez@galgus.net>
When configuring the radio in legacy mode from luci, the htmode is not set
correctly to NOHT, causing the radio in mesh mode to be set to HT40.
Signed-off-by: Enrique Rodríguez Valencia <enrique.rodriguez@galgus.net>
Add a local hack to prevent the Broadcom WPA authenticator process from
inheriting the lock descriptor 1000 used to prevent concurrent executions
of the init script.
Without this fix, repeated invocations of /etc/init.d/network, e.g. for
obtaining the enabled state, would hang forever.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Support for 64 bits has been remove on latest master of raspberry/firmware.
Update to latest commit with 64 bit support since we don't support
installing 32 bit packages on 64 bit targets.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This patch backports additional fixes for XDP support in the mvneta driver. These
changes are found upstream as commits:
b37fa92e20ef2 net: mvneta: fix build skb for bm capable devices
f383b2950070c net: mvneta: rely on page_pool_recycle_direct in mvneta_run_xdp
79572c98c554d mvneta driver disallow XDP program on hardware buffer management
44efc78d0e464 net: mvneta: fix XDP support if sw bm is used as fallback
Signed-off-by: Jakov Petrina <jakov.petrina@sartura.hr>
This patch backports XDP support in the mvneta driver used by Marvell ARMADA 37x,
38x and 37xx series SoCs. Supported actions are:
- XDP_DROP
- XDP_PASS
- XDP_REDIRECT
- XDP_TX
Patches are present upstream as following commits:
* b0a43db9087a net: mvneta: add XDP_TX support
* 9e58c8b41065 net: mvneta: make tx buffer array agnostic
* fa383f6b77a2 net: mvneta: move header prefetch in mvneta_swbm_rx_frame
* 0db51da7a8e9 net: mvneta: add basic XDP support
* 8dc9a0888f4c net: mvneta: rely on build_skb in mvneta_rx_swbm poll routine
* 568a3fa24a95 net: mvneta: introduce page pool API for sw buffer manager
* ff519e2acd46 net: mvneta: introduce mvneta_update_stats routine
Signed-off-by: Jakov Petrina <jakov.petrina@sartura.hr>
The clean target tries to remove what looks like a bogus 'rbcfg',
probably carried over copy-pasta. Remove the name of the generated
executable ('fbtest') instead.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Fixes: 8099f4e0d3 ("fbtest utility ")
tl;dr: dd will silently truncate the output if reading from special
files (e.g. sysfs attributes) with a too large bs parameter.
This problem was exposed on some RouterBOARD ipq40xx devices which use a
caldata payload which is larger than PAGE_SIZE, contrary to all other
currently supported RouterBOARD devices: the caldata would fail to
properly load with the current scripts.
Background: dd doesn't seem to correctly handle read() results that
return less than requested data. sysfs attributes have a kernel exchange
buffer which is at most PAGE_SIZE big, so only 1 page can be read() at a
time. In this case, if bs is larger than PAGE_SIZE, dd will silently
truncate blocks to PAGE_SIZE. With the current scripts using bs=<size>
count=1, the data is truncated to PAGE_SIZE as soon as the requested
<size> exceeds this value.
This commit works around this problem by using `cat` in the caldata
routines that can read from a file (routines that read from mtd devices
are untouched). cat correctly handles partial read requests. The output
is then piped to dd with the same parameters as before, to ensure that
the resulting file remains exactly the same.
This is a simple workaround, the downside is that it uses a pipe and one
more executable, and therefore has a larger memory footprint and is
slower. This is deemed acceptable considering these routines are only
used at boot time.
Tested-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
This commit introduces support for R/W access to the CPU frequency
setting of routerboot on ath79 hardware.
On unsupported hardware, the sysfs attribute will expose the raw tag
value (read-only) to help with reverse engineering its meaning.
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
This routine will be shared between hard and soft config drivers.
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
This driver exposes the data encoded in the "soft_config" flash segment
of MikroTik RouterBOARDs devices. It presents the data in a sysfs folder
named "soft_config" through a set of human-and-machine-parseable
attributes. Changes can be discarded by writing 0 to the 'commit'
attribute, or they can be committed to flash storage by writing 1.
This driver does not reuse any of the existing code previously found in
the "rbcfg" utility and makes this utility obsolete by providing a clean
sysfs interface.
Like "rbcfg", this driver requires 4K_SECTORS support since the flash
partition in which these parameters are stored is typically 4KB in size.
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
This routine will be shared between hard and soft config drivers.
Also use scnprintf() instead of snprintf().
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
For the sake of strictly typed code, add a missing const qualifier.
Add a missing return value in error path.
Check the return value of mtd_read(), for good measure.
Also demote the error printks of failed sysfs file creation to warn
level since they are not fatal in the init() sequence.
Finally, add a note regarding PAGE_SIZE and clarify a comment.
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
The depends and select should apply to the sysfs driver, not the meta
config.
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
This patch adds support for the COMFAST CF-E130N v2, an outdoor wireless
CPE with a single Ethernet port and a 802.11bgn radio.
Specifications:
- QCA9531 SoC
- 1x 10/100 Mbps Ethernet with PoE-in support
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- 5 dBi built-in antenna
- POWER/LAN/WLAN green LEDs
- 4x RSSI LEDs (2x red, 2x green)
- UART (115200 8N1) and GPIO (J9) headers on PCB
Flashing instructions:
The original firmware is based on OpenWrt so a sysupgrade image can be
installed via the stock web GUI.
The U-boot bootloader also contains a backup TFTP client to upload the
firmware from. Upon boot, it checks its ethernet network for the IP
192.168.1.10. Host a TFTP server and provide the image to be flashed as
file firmware_auto.bin.
MAC address setup:
The art partition contains four consecutive MAC addresses:
0x0 aa:bb:cc:xx:xx:c4
0x6 aa:bb:cc:xx:xx:c6
0x1002 aa:bb:cc:xx:xx:c5
0x5006 aa:bb:cc:xx:xx:c7
However, the manufacturer in its infinite wisdom decided that one address
is enough and both eth0 and WiFi get the MAC address from 0x0 (yes, that's
overwriting the existing and valid address in 0x1002). This is obviously
also the address on the device's label.
Signed-off-by: Pavel Balan <admin@kryma.net>
[fix configs partition, fix IMAGE_SIZE, add MAC address comment, rename
ATH_SOC to SOC]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
AHB is 258 MHz for this device (CPU_PLL / 3), but there is no difference
between 64 MHz and 50 MHz for spi-max-frequency, thus increase to 50 MHz.
Tested on revisions C1 and C3.
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
GPIO 11 needs to be pulled high for the external gigabit switch to work,
this is currently solved via gpio-hog. Replace with phy0 reset-gpios.
Tested on revisions C1 and C3. Reset button is still working for reboot,
to enter failsafe, and to enter bootloader http recovery.
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
The device has a total of 8 LEDs, 5 of which are controlled by the switch
(LAN 1-4, WAN). Only power, wifi and wps are controlled by the SoC.
* led_power is on GPIO 5 (not 15), boot flashing sequence is now visible
* remove led 'internet', since it is only connected to the switch
* remove ucidef_set_led_switch for WAN from 01_leds, as it has no effect
Tested on revisions C1 and C3.
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
[adjust commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
* MediaTek MT7620A (580 Mhz)
* 8 MB of FLASH
* 64 MB of RAM
* 2.4Ghz and 5.0Ghz radios
* 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN)
* UART header on PCB (57600 8n1)
* Green/Orange Power LEDs illuminating a Power-Button Lens
* Green/Orange Internet LEDs GPIO controlled illuminating a Globe/Internet Lens
* 3x button - wps, power and reset
* U-boot bootloader
Installation:
The sysupgrade.bin image is reported to be OEM web flashed with an ncc_att_hwid
appended. ncc_att_hwid is a 32bit binary in the GPL Source download for either
the TEW-810DR or DIR-810L and is located at
source/user/wolf/cameo/ncc/hostTools.
The invocation is: ncc_att_hwid -f tew-810dr-squashfs-factory.bin -a -m "TEW-810DR" -H "1.0R" -r "WW" -c "1.0"
This may need to be altered if your hardware version is "1.1R".
The image can also be directly flashed via serial tftp:
1. Load *.sysupgrade.bin to your tftp server directory and rename for
convenience.
2. Set a static ip 192.168.10.100.
3. NIC cable to a lan port.
4. Serial connection parameters 57600,8N1
5. Power on the TEW-810 and press 4 for a u-boot command line prompt.
6. Verify IP's with U-Boot command "printenv".
7. Adjust tftp settings if needed per the tftp documentation
8. Boot the tftp image to test the build.
9. If the image loads, reset your server ip to 192.168.1.10 and restart network.
10. Log in to Luci, 192.168.1.1, and flash the *sysupgrade.bin image.
Notes:
The only valid MAC address is found in 0x28 of the factory partition.
Other typical offsets/caldata only contain example data: 00:11:22:00:0f:xx
Signed-off-by: J. Scott Heppler <shep971@centurylink.net>
[remove "link rx tx" in 01_leds, format and extend commit message,
fix DTS led node names]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The UBIFS_FS_ZSTD is exposed when UBIFS is enabled.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[adjust commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
