At this moment, 702-phy-Add-2.5G-SGMII-interface-mode.patch cause error
durring kernel compilation:
CC drivers/net/phy/phylink.o
drivers/net/phy/phylink.c: In function 'phylink_get_capabilities':
drivers/net/phy/phylink.c:443:9: error: enumeration value 'PHY_INTERFACE_MODE_2500SGMII' not handled in switch [-Werror=switch]
443 | switch (interface) {
| ^~~~~~
cc1: all warnings being treated as errors
NXP take care of it. Let's port their patch.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Patches recreated from NXP 6.1 tree:
400-LF-20-3-mtd-spi-nor-Use-1-bit-mode-of-spansion-s25fs.patch
701-staging-add-fsl_ppfe-driver.patch
702-phy-Add-2.5G-SGMII-interface-mode.patch
Patch 703 includes changes made by Christian Marangi, extracted from commit
0d4a547905.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Some MT7915 devices need to load the second part of the eeprom to
work properly. The mt76 driver is not yet ready to read the pre-cal
data via the NVMEM cell. Therefore, partially revert commit to fix
the device probe issue on some devices.
P.S.
Except for D-Link and Ubnt devices, It is still uncertain whether
pre-cal data is required for other devices in the patch.
This partially reverts commit 9ac891f8c4.
Fixes: https://github.com/openwrt/openwrt/issues/13700
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Telco Electronics X1 has MT7603E and MT7612E PCIe NICs. They are
driven by kmod-mt7603 and kmod-mt76x2.
Ref: 73e0f52b6e ("ramips: add support for Telco Electronics X1")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
The starting address of 'factory' partition is 0x40000, and the
starting address of the next partition is 0x50000. It's obvious
that the correct size for the 'factory' is 0x10000, just like
other MT7620 devices.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
These three devices uses MT7612E PCIe NIC and supported by the
'mt76' driver. So the right frequency limit property should be
`ieee80211-freq-limit`.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
On the ramips target, all 'wmac' nodes in SoC dtsi are enabled by
default except mt7628. There is no need to mark them as 'okay'
again. So these useless properties can be removed.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
This patch converts MT761{0,2,3} PCIe WiFi calibration data to NVMEM
format for legacy Ralink SoCs (MT7620 and Mt7628). The EEPROM size of
the MT7610 and MT7612 is 0x200. there are only three devices uses
MT7613 NIC, ASUS RT-AC1200 V2, COMFAST CF-WR758AC V2 and Keenetic
KN-1613. The EEPROM size of them is 0x4da8.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
This patch converts legacy Ralink SoCs and MT7620 WiFi calibration
data to NVMEM format. The EEPROM size is 0x200.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
The mtd partition node name should be "partition@${offset}".
However, the offsets of the PSG1208 don't match the partition
'reg' properties. This patch correct the wrong offsets.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
The MT7628 integrated wireless is driven by `mt76`, so the right
EEPROM property name is `mediatek,mtd-eeprom`.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
`mtd-mac-address` has been abandoned. Therefore, convert them to
NVMEM format. This patch also removes some useless mtd-mac-address
properties.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
IPQ8074 CPUFreq NVMEM support has finally landed upstream, so lets use the
upstreamed version.
This has a benefit of also supporting IPQ8174 (Oak) family for which SMEM
SoC ID-s were also upstreamed.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Binding for ralink EEPROM swap changed from ralink,mtd-eeprom-swap to
ralink,eeprom-swap.
Update every entry.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
A typo snuck in with the addition of Cudy M1800, changing
"nr7101" to "nt7101". The result is a default network config
for NR7101 without the only ethernet interface on the NR7101,
thereby soft bricking it.
Fixes: f6d394e9f2 ("ramips: add support for Cudy M1800")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
SBL will configure IPQ807x cores to boot at 800MHz as a safe default
frequency that is provided by GPLL0, but GPLL0 is not currently configured
as a possible parent in the APSS clock driver not being passed to it via
DTS which will then cause the kernel to not properly identify the current
CPU frequency during booting and will think that CPU is currently at XO
frequency of 19.2MHz instead of 800MHz cores are actually at and print:
cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 19200 KHz, changing to: 1017600 KHz
So, lets import patches pending upstream to prevent GPLL scaling and feed
the GPLL0 clock to APSS clock driver so we get:
cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 800000 KHz, changing to: 1017600 KHz
This is mostly cosmetic fix, but with all of the possible SBL and FW
versions there could be edge cases resolved by this and not scaling GPLL-s
anymore.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Disable new ksym globally as OpenWrt does not have any targets that
use A520 cores.
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: John Audia <therealgraysky@proton.me>
The compex WPJ563 actually has both usb controllers wired:
usb0 --> pci-e slot
usb1 --> pin header
As the board exposes it for generic use, enable this controller too.
fixes: #13650
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
So far every build of a single bcm53xx Target Profile (it means: when
NOT using CONFIG_TARGET_MULTI_PROFILE) resulted in all target devices
images being built. Now it only builds the one matching selected
profile.
Fixes: #13572
Suggested-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Rani Hod <rani.hod@gmail.com>
[rmilecki: update commit subject + body & move PROFILES line]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Hardware information:
---------------------
- RTL8380 SoC
- 8 Gigabit RJ45 PoE ports (built-in RTL8218B)
- 2 SFP ports (built-in SerDes)
- RJ45 RS232 port on front panel
- 32 MiB NOR Flash
- 128 MiB DDR3 DRAM
- PT7A7514 watchdog
- PoE chip
- Fanless
Known issues:
---------------------
- PoE LEDs are uncontrolled.
(Manual taken from f2f09bc)
Booting initramfs image:
------------------------
- Prepare a FTP or TFTP server serving the OpenWrt initramfs image and
connect the server to a switch port.
- Connect to the console port of the device and enter the extended
boot menu by typing Ctrl+B when prompted.
- Choose the menu option "<3> Enter Ethernet SubMenu".
- Set network parameters via the option "<5> Modify Ethernet Parameter".
Enter the FTP/TFTP filename as "Load File Name" ("Target File Name"
can be left blank, it is not required for booting from RAM). Note that
the configuration is saved on flash, so it only needs to be done once.
- Select "<1> Download Application Program To SDRAM And Run".
Initial installation:
---------------------
- Boot an initramfs image as described above, then use sysupgrade to
install OpenWrt permanently. After initial installation, the
bootloader needs to be configured to load the correct image file
- Enter the extended boot menu again and choose "<4> File Control",
then select "<2> Set Application File type".
- Enter the number of the file "openwrt-kernel.bin" (should be 1), and
use the option "<1> +Main" to select it as boot image.
- Choose "<0> Exit To Main Menu" and then "<1> Boot System".
NOTE: The bootloader on these devices can only boot from the VFS
filesystem which normally spans most of the flash. With OpenWrt, only
the first part of the firmware partition contains a valid filesystem,
the rest is used for rootfs. As the bootloader does not know about this,
you must not do any file operations in the bootloader, as this may
corrupt the OpenWrt installation (selecting the boot image is an
exception, as it only stores a flag in the bootloader data, but doesn't
write to the filesystem).
Example PoE config file (/etc/config/poe):
---------------------
config global
option budget '65'
config port
option enable '1'
option id '1'
option name 'lan8'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '2'
option name 'lan7'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '3'
option name 'lan6'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '4'
option name 'lan5'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '5'
option name 'lan4'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '6'
option name 'lan3'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '7'
option name 'lan2'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '8'
option name 'lan1'
option poe_plus '1'
option priority '2'
Signed-off-by: Kevin Jilissen <info@kevinjilissen.nl>
There are two hardware models of the HPE 1920-8g-poe switch. The version
currently in the repository is the model with a PoE budget of 180W. In
preparation of the addition of the 65W model, the existing model is
renamed to clarify the hardware version it targets.
As suggested by Pawel, the 'SUPPORTED_DEVICES' includes the old target
name to enable an upgrade path of builds with the old name.
Suggested-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Kevin Jilissen <info@kevinjilissen.nl>
The driver for the cellular modems serial interface was missing from the
default device packages.
The driver is required to interact with the modem using AT commands.
Other devices with a 4G modem also ship with this package, thus let's
add it to the default packages for the board.
Signed-off-by: David Bauer <mail@david-bauer.net>
Fix broken onhub dtsi. The gmac node have a redundant phy-handle that
doesn't point to the swconfig phy node as they got dropped in the DSA
conversion. Drop these extra binding to restore correct compilation of
this subtarget.
Fixes: 337e36e0ef ("ipq806x: convert each device to DSA implementation")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The node name&label should match the address in the 'reg' property,
so it's better to change the incorrect offset to the 0x28.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
I-O DATA WN-DEAX1800GR uses MT7915 PCIe NIC. The correct EEPROM
size is 0xe00.
Fixes: ac68fbf526 ("ramips: add support for I-O DATA WN-DEAX1800GR")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Backport qca8k fixes for big endian system (to make them working again)
and a patch fixing MDIO conflicts if other PHY are connected and mgmt
eth is used to control the switch.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch enabling assisted learning for qca8k to fix roaming issue
between BSS and BSS on the same L2 broadcast domain.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Symbol rtl8366_enable_vlan and rtl8366_reset_vlan are also present in
the DSA driver upstream and conflicts as they are EXPORTED.
Rename them to rtl8366_smi_enable_vlan and rtl8366_smi_reset_vlan to fix
the conflict. While at it also make them static and drop the
EXPORT_SYMBOL_GPL as they are not actually used by any other driver and
exporting them is useless.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
In userspace, ASLR is enabled, but it's missing to enable KASLR on the
kernel side to improve security as part of SystemReady recommendations.
Signed-off-by: Javier Tia <javier.tia@linaro.org>
The name of the variable holding the pointer to the private struct has
changed between Linux 5.15 and Linux 6.1 and adding the identical patch
fixing PCIe #PERST de-assert broke the build on Linux 6.1.
Also change the name in the patch to fix the build.
Fixes: 6a2e17d5c1 ("mediatek: fix PCIe #PERST being de-asserted too early")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fix copy-paste error in migrating NEC Aterm WG2600HP3 to new LED
implementation for the QCA8K switch. Correct define the missing
additional LED pin used for each port and fix wrong color for LED 2 for
each port. Also add the required function-enumerator as all 3 LED have
the same color and function.
Fixes: c707cff6c9 ("ipq806x: add LEDs definition for non-standard qca8k LEDs")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
