The previous workaround for the unsupported mkimage xz compression
leads to the TP-Link TL-WDR4900s simpleImage bootwrapper being gzip
compressed, which does not fit the kernel partition.
Removing the uImage gerneration works around this problem.
Signed-off-by: David Bauer <mail@david-bauer.net>
This fixes some outstanding issues with the Kernel 5.4 build:
* Adds missing support patch for the Enterasys WS-AP3710i
* Fixes incorrect NAND symbols
* Adds patch for broken image wrapping
Signed-off-by: David Bauer <mail@david-bauer.net>
This move the slightly different target-specific implementations of
mktplinkfw from the targets to include/image-commands.mk and renames
it to tplink-v1-image. Having a common version will increase
consistency between implementation and will complete the
tplink build command already present in the new location.
Due to the slight differences of the original implementations, this
also does some adjustments to the device build commands/variables.
This also moves rootfs_align as this is required as dependency.
Tested on:
- TL-WDR4300 v1 (ath79, factory)
- TL-WDR4900 v1 (mpc85xx, sysupgrade)
- RE210 v1 (ramips, see Tested-by)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Christoph Krapp <achterin@googlemail.com>
Hardware
--------
SoC: NXP P1020 (2x e500 @ 800MHz)
RAM: 256M DDR3 (Micron)
FLASH: 32M NOR (Spansion S29GL128S)
BTN: 1x Reset
WiFi: 1x Atheros AR9590 2.4 bgn 3x3
2x Atheros AR9590 5.0 an 3x3
ETH: 1x Gigabit Ethernet (Atheros AR8033)
LED: System (green/red) - Radio{0,1} (green)
LAN (connected to PHY)
- GE blue
- FE green
Serial is a Cisco-compatible RJ45 next to the ethernet port.
115200-N-8 are the settings for OS and U-Boot.
Installation
------------
1. Grab the OpenWrt initramfs, rename it to 01C8A8C0.img. Place it in
the root directory of a TFTP server and serve it at
192.168.200.200/24.
2. Connect to the serial port and boot the AP. Stop autoboot in U-Boot
by pressing Enter when prompted. Credentials are identical to the one
in the APs interface. By default it is admin / new2day.
3. Set the bootcmd so the AP can boot OpenWrt by executing
$ setenv boot_openwrt "setenv bootargs;
cp.b 0xee000000 0x1000000 0x1000000; bootm 0x1000000"
$ setenv bootcmd "run boot_openwrt"
$ saveenv
If you plan on going back to the vendor firmware - the bootcmd for it
is stored in the boot_flash variable.
4. Load the initramfs image to RAM and boot by executing
$ tftpboot 0x1000000 192.168.200.200:01C8A8C0.img; bootm
5. Make a backup of the "firmware" partition if you ever wish to go back
to the vendor firmware.
6. Upload the OpenWrt sysupgrade image via SCP to the devices /tmp
folder.
7. Flash OpenWrt using sysupgrade.
$ sysupgrade -n /tmp/openwrt-sysupgrade.bin
Signed-off-by: David Bauer <mail@david-bauer.net>
By adding the vendor to the Makefile device definition node name,
one can derive the standard compatible used in SUPPORTED_DEVICES
instead of having to specify it manually.
Despite, this moves the naming scheme closer to what is used for
other targets (ath79, ramips).
Build-tested on all subtargets.
Run-tested on TP-Link TL-WDR4900 v1.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit fixes TP-Link TL-WDR4900 v1 MAC address assignment.
Previously, the MAC addrss was read for the ethernet from the "config"
partition. However, the content of this partition is dependent on the
firmware which was previously installed on the device.
Switch the MAC address source to the U-Boot partition, where the MAC
address is always present at a fixed partition. The partition was
previously already used for the WiFi MAC-addresses.
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
This unifies MAC address patch functions and moves them to a
common script. While those were implemented differently for
different targets, they all seem to do the same. The number of
different variants is significantly reduced by this patch.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This moves the almost identical calibration data extraction
functions present multiple times in several targets to a single
library file /lib/functions/caldata.sh.
Functions are renamed with more generic names to merge different
variants that only differ in their names.
Most of the targets used find_mtd_chardev, while some used
find_mtd_part inside the extraction code. To merge them, the more
abundant version with find_mtd_chardev is used in the common code.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[rebase on latest master; add mpc85xx]
Signed-off-by: David Bauer <mail@david-bauer.net>
This changes size and offset set for WiFi caldata extraction and
MAC address adjustment to hexadecimal notation.
This will be much clearer for the reader when numbers are big, and
will also match the style used for mtd-cal-data in DTS files.
Since dd cannot deal with hexadecimal notation, one has to convert
back to decimal by simple $(($hexnum)).
Acked-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This changes the offsets for the MAC address location in
mtd_get_mac_binary* and mtd_get_mac_text to hexadecimal notation.
This will be much clearer for the reader when numbers are big, and
will also match the style used for mtd-mac-address in DTS files.
(e.g. 0x1006 and 0x5006 are much more useful than 4102 and 20486)
Acked-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
WLAN0 and the unused LED are currently swapped. Fix this, so the LED
behavior matches the other OCEDo devices.
Signed-off-by: David Bauer <mail@david-bauer.net>
After commit 1e41de2f48 ("mpc85xx: convert TL-WDR4900 v1 to simpleImage")
XZ compression of zImage was enabled. This change exposed a problem with
the HiveAP-330 images, which was fixed by foregoing the compression on
the kernel altogether with commit 98089bb8ba
("mpc85xx: Use uncompressed kernel on the HiveAP-330").
This patch adds back the gzip compression of the kernel image by
utilizing the generic OpenWRT uImage method instead of relying on
the PowerPC bootwrapper script that did it previously.
Compile-tested: p1020/hiveap-330
Tested-by: Chris Blake <chrisrblake93@gmail.com> [run-tested]
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[filled in even more text]
It seems that newer builds of OpenWRT have a gzip kernel
larger than 2MB~, which for some reason fails to boot on this board.
However, we have 8MB of kernel space and currently the uncompressed
kernel is 6.5MB~, so we have some space to grow until a better
solution is worked out.
Before:
## Booting kernel from Legacy Image at ee840000 ...
Image Name: Linux-4.19.53
Created: 2019-06-22 11:17:48 UTC
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 2315724 Bytes = 2.2 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 02000000 ...
Image Name: OpenWrt fake ramdisk
Created: 2019-06-22 11:17:48 UTC
Image Type: PowerPC Linux RAMDisk Image (uncompressed)
Data Size: 0 Bytes = 0 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at ec000000
Booting using the fdt blob at 0xec000000
Uncompressing Kernel Image ... Error: Bad gzipped data
GUNZIP: uncompress, out-of-mem or overwrite error -
must RESET board to recover
Loading Ramdisk to 10000000, end 10000000 ... OK
Loading Device Tree to 00ffa000, end 00fffc78 ... OK
ft_fixup_l2cache: FDT_ERR_NOTFOUND
After:
## Booting kernel from Legacy Image at ee840000 ...
Image Name: POWERPC OpenWrt Linux-4.19.53
Created: 2019-06-22 11:17:48 UTC
Image Type: PowerPC Linux Kernel Image (uncompressed)
Data Size: 6724584 Bytes = 6.4 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 02000000 ...
Image Name: OpenWrt fake ramdisk
Created: 2019-06-22 11:17:48 UTC
Image Type: PowerPC Linux RAMDisk Image (uncompressed)
Data Size: 0 Bytes = 0 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at ec000000
Booting using the fdt blob at 0xec000000
Loading Kernel Image ... OK
OK
Loading Ramdisk to 10000000, end 10000000 ... OK
Loading Device Tree to 00ffa000, end 00fffc78 ... OK
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [75 cpl limit]
Lets bump kernel to 4.19 on targets which were run tested or got ACKed
so we've enough time to make it ready for next release:
armvirt/32 (runtested in qemu)
armvirt/64 (runtested in qemu)
ath79/generic (runtested on Carambola2)
gemini/generic (runtested on DIR-685, DNS-313, SQ201, SL93512R)
imx6/generic (runtested on Apalis)
ipq40xx/generic (runtested on nbg6617)
malta/be64 (runtested in qemu)
malta/be (runtested in qemu)
malta/le (runtested in qemu)
malta/le64 (runtested in qemu)
mpc85xx/generic (runtested on TL-WDR4900)
mpc85xx/p2020 (runtested on P2020RDB)
mvebu/cortexa53
mvebu/cortexa72
mvebu/cortexa10
octeon/generic (runtested on EdgeRouter Lite)
sunxi/cortexa53 (build tested only)
sunxi/cortexa7 (runtested on Lime2-K)
sunxi/cortexa8 (build tested only)
tegra/generic
x86/64 (runtested in qemu)
Acked-by: Zoltan HERPAI <wigyori@uid0.hu> [sunxi]
Tested-by: Linus Walleij <linus.walleij@linaro.org> [gemini]
Tested-by: Tomasz Maciej Nowak <tomek_n@o2.pl> [mvebu, tegra]
Tested-by: Daniel Engberg <daniel.engberg.lists@pyret.net> [octeon]
Tested-by: Pawel Dembicki <paweldembicki@gmail.com> [mpc85xx/generic mpc85xx/p2020]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Refreshed all patches.
This bump contains upstream commits which seem to avoid (not properly fix)
the errors as seen in FS#2305 and FS#2297
Altered patches:
- 403-net-mvneta-convert-to-phylink.patch
- 410-sfp-hack-allow-marvell-10G-phy-support-to-use-SFP.patch
Compile-tested on: ar71xx, cns3xxx, imx6, mvebu, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6, x86_64
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Converts the TP-Link WDR4900 v1 to use the simpleImage in the
hopes of prolonging the life of the device. While at it,
the patch makes the fdt.bin an ARTIFACT and sets the KERNEL_SIZE
to 2684 KiB as a precaution since the stock u-boot is using a
fixed kernel size.
Note: Give the image some time, it will take much longer to
extract and boot.
[tested for 4.14/4.19]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Co-authored-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
If the target supports a newer kernel version that is not used by default
yet, it can be enabled with this option
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Both targets have their own idea of how to use ehci-fsl.
This patch reverts part of commit
68b8d3b079 ("kernel: usb: add FSL EHCI package") and moves
ehci-fsl back into kmod-usb2, while also making it hopefully
useable for the mpc85xx target.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The current mpc85xx build is failing because the
TL-WDR4900v1 kernel image no longer fits into the
partition. Extending the kernel is not possible
without updating u-boot's kernel loader commands.
This patch disables the WDR4900v1 until the kernel
image size issue is fixed so the buildbot can still
compile the Sophos RED 15w Rev.1 . Installing the
WDR4900v1 images would cause the routers to get
bricked.
For the discussion, please go to:
<https://github.com/openwrt/openwrt/pull/1773>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
TP-Link TL-WDR 4900 have u-boot with read-only env.
Boot command read only 0x29F000 data from flash.
Bigger images causes crc error. It can't be changed.
This patch add kernel size checking.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [utilize KERNEL_SIZE]
Remove wireless and USB packages from the device-specific package
selection as they are already selected by the target itself.
Signed-off-by: David Bauer <mail@david-bauer.net>
This removes USB support from the compiled kernel. Because of this, the
kernel is just small enough for the TP-Link WDR4900 to boot the
resulting kernel.
This is necessary to support the WDR4900 in the upcoming 19.xx release.
In the long run, this should be fixed with a second stage bootloader, as
the vendor bootloader only loads the first 2684k bytes.
Signed-off-by: David Bauer <mail@david-bauer.net>
At some point our initramfs image grew over 6MB, which is
causing an issue when uncompressing in the stock bootloader:
=> bootm 0x5000000 - 0x1000000;
Image Name: Linux-4.19.24
Created: 2019-02-23 1:58:20 UTC
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 6752470 Bytes = 6.4 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Booting using the fdt blob at 0x1000000
Uncompressing Kernel Image ... Error: inflate() returned -5
GUNZIP: uncompress, out-of-mem or overwrite error - must RESET
board to recover
Loading Device Tree to 00ffa000, end 00fffc78 ... OK
To get around this, we need to move to an uncompressed image
for the initramfs image. While this makes a larger image, it
is thankfully bootable so people can then convert their
devices to run OpenWRT. It's worth noting the non-initramfs
image is under 3M, so it will be ages before we have any issues
with the flashed kernel.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[keep commit message at less than 75 characters per line]
OCEDO Panda was added in b368373f, but only for
4.14 config. This patch fix 4.19 build for generic
and p2020 subtarget.
Signed-off-by: Pawel Dembicki <p.dembicki@wb.com.pl>
CPU: FSL P1020 (2x 800MHz E500 PPC)
RAM: 1GB DDR3
FLASH: 256MiB NAND
WiFi: 2x Atheros AR9382 2x2:2 abgn
ETH: 2x BCM54616S - 1x BCM53128 8-port switch
LED: 5x LEDs (Power, WiFi1, WiFi2, N/D, SYS)
BTN: 1x RESET
Installation
------------
1. Download initrams kernel image, dtb binary and sysupgrade image.
2. Place initramfs kernel into tftp root directory. Rename to
"panda-uimage-factory".
3. Place dtb binary into tftp root directory. Rename to "panda.fdt".
4. Start tftp server on 192.168.100.8/24.
5. Power up the device with the reset button pressed. It will download
the initrams and dtb via tftp and boot into OpenWRT in RAM.
6. SSH into the device and remove the factory partitions.
> ubirmvol /dev/ubi0 --name=kernel1
> ubirmvol /dev/ubi0 --name=rootfs1
> ubirmvol /dev/ubi0 --name=devicetree1
You will have around 60 MiB of free space with that.
You can also delete "kernel2", "devicetree2", "rootfs2" and "storage"
respectively in case you do not want to go back to the vendor firmware.
7. Modify the U-Boot bootcmd to allow for booting OpenWRT
> fw_setenv bootcmd_owrt "ubi part ubi && ubi read 0x1000000 kernel
&& bootm 0x1000000"
> fw_setenv bootargs_owrt "setenv bootargs console=ttyS0,115200
ubi.mtd=3,2048"
> fw_setenv bootcmd "run bootargs_owrt; run bootcmd_owrt"
8. Transfer the sysupgrade image via scp into the /tmp directory.
9. Upgrade the device
> sysupgrade -n /tmp/<imagename>
Signed-off-by: David Bauer <mail@david-bauer.net>
This commit removes the target-specific diag.sh script. This way, the
generic one is used for the target, which uses DT-aliases to specify the
LEDs used.
This way, we are also able to use different LEDs to indicate different
states. We use green status LEDs for indicating boot and a running
system. Where possible, the red status LED is used to indicate failsafe
mode and a running upgrade.
Signed-off-by: David Bauer <mail@david-bauer.net>
Hardware
========
CPU: Freescale P1010 PowerPC
RAM: 128M DDR3
NAND: 128MiB
ETH: RTL8211F SGMII PHY
RTL8367B 5-port RGMII switch
(not connected to SoC - unmanaged)
WiFi: SparkLan WPEA-121N
- Atheros AR9382 2T2R abgn
USB: 1x USB 2.0
LED: System, Router, Internet, Tunnel controllable
LAN1-4, WAN, Power non-controllable
BTN: None
Installation
============
1. Power on the device while attached to the Console port.
2. Halt the U-Boot by pressing Enter when prompted.
3. Set the correct bootcmd for booting OpenWRT:
> setenv bootargs_owrt "setenv bootargs console=ttyS0,115200"
> setenv bootcmd "run bootargs_owrt;
nand read 0x1000000 0x300000 0x800000;
bootm 0x1000000;"
> saveenv
5. Rename OpenWRT initramfs image to 'kernel.bin' and place it in a
TFTP server root-directory served on 192.168.1.2/24. Connect your
computer to one of the LAN-ports.
4. Boot OpenWRT initramfs image with
> run bootargs_owrt; tftpboot 0x1000000 192.168.1.2:kernel.bin;
bootm 0x1000000;
6. (Optional)
Make a Backup of 'sophos-os1', 'sophos-os2' and 'sophos-data' in case
you ever want to go back to the vendor firmware.
7. Create Ubi Volume on mtd4 by executing
> ubiformat /dev/mtd4 -y
8. Transfer OpenWRT sysupgrade image to the device via SCP and install it
with
> sysupgrade -n <openwrt-image-file>
Back to Stock
=============
If you want to go back to the stock firmware, here is the bootcmd of the
vendor firmware:
> setenv bootargs console=ttyS0,115200 root=/dev/mtdblock5;
nand read 0xc00000 0x00300000 0x100000;
nand read 0x1000000 0x00400000 0x00800000;
bootm 0x1000000 - 0xc00000
Set it via 'setenv' from the U-Boot shell and don't forget to save it
using 'saveenv'!
After this, boot the OpenWRT initramfs image just like you would for
installation. Write back the three vendor partitions using mtd. Reboot
the device afterwards.
Signed-off-by: David Bauer <mail@david-bauer.net>
[refresh and reorder patches]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Initramfs image isn't required for this device and regular
initramfs generation isn't work properly. It create not working
binaries.
This patch disable initramfs image for TL-WDR4900.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Copied config from 4.14
Add patches for 4.19
Drop patch 103-powerpc-fix-build-cross32ar.patch,
because issue was fixed in upstream.
Compiled: generic p1020
Compiled and tested: (unofficial) P2020, TP-Link TL-WDR4900
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded commit]
