Some u-boot versions for QCA955x change the delays based on the link speed
during boot. This usually breaks the support of other linkspeeds when
OpenWrt is booted. It also conflicts with the
at803x_platform_data::fixup_rgmii_tx_delay. OpenWrt has to set its own
values in QCA955X_GMAC_REG_ETH_CFG.
The default RGMII values from the Atheros u-boot are currently used to
preset the existing mach files. These may have to be adjusted for boards
using different values but which are not currently set them explicitely in
OpenWrt.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Christian Beier <cb@shoutrlabs.com>
Cc: Chris R Blake <chrisrblake93@gmail.com>
Cc: Benjamin Berg <benjamin@sipsolutions.net>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Cc: Matthias Schiffer <mschiffer@universe-factory.net>
Cc: Dirk Neukirchen <dirkneukirchen@web.de>
Cc: Christian Mehlis <christian@m3hlis.de>
Cc: Luka Perkov <luka@openwrt.org>
Cc: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 49029
Some u-boot versions for QCA955x set currently not cleared bits depending
on the used link speed. This breaks the rx/tx under OpenWrt. The mach-*.c
file is responsible to select the correct configuration bits and thus the
ath79_setup_qca955x_eth_cfg has to clear the unset.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49028
Complete internal switch initialization for QCA956X.
Set default mdio device if the interface mode of GE0 is not SGMII (fix ticket #21520).
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
SVN-Revision: 48937
This patch provides full GPIO support for WNR612v2 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48924
This patch provides full GPIO support for WNR2000v3 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48922
Enable platform-supplied WLAN LED name for ath9k device.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Acked-by: Hartmut Knaack <knaack.h@gmx.de>
SVN-Revision: 48879
Fix for invalid/random WLAN MAC address in WNR612v2. Permanent platform
MAC is calculated and assigned during system startup. WLAN MAC follows
wired Ethernet interface addresses. This is the same fix as for WNR2000v3.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48779
Fix for invalid/random WLAN MAC address in WNR2000v3. Permanent platform
MAC is calculated and assigned during system startup. WLAN MAC follows
wired Ethernet interface addresses.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48777
This patch adds support for the Bitmain Antrouter R1
http://wiki.openwrt.org/toh/bitmain/r1
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 48058
In r45970 the MAC swap handling was made opt-in, however some boards
have been forgotten during the conversion. Since the reference design
uses this MAC swapping, and pretty much all known boards using this chip
seem to do so too, enabling the swapping is a more reasonable default
than leaving it disabled.
Change the code to still allow boards to opt-out of this.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47956
The following patch is to add ath79_register_m25p80_large, which sets
is_flash to false to support bit banging. This is needed on some 32MB+
SPI chips, such as the S25FL256S1
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
SVN-Revision: 47952
Kernel part of support for the PowerCloud Systems CR5000. The
CR5000 is a dual-band 802.11n wireless router with 8MB flash,
64 MB RAM, (unused in stock firmware) USB 2.0 port, and five
port gigabit ethernet switch. The CR5000 was sold as hardware for
the Skydog cloud-managed router service.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47940
Kernel part of support for PowerCloud CR3000. The CR3000 is
a 802.11n 2.4 GHz wireless router with 8MB flash, 64MB RAM,
a four port fast ethernet switch, and a fast ethernet wan port which
was sold by PowerCloud Systems as hardware for the Skydog
cloud-managed router service.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47939
Kernel part of support for PowerCloud CAP324 Cloud AP.
The CAP324 Cloud AP was a device sold by PowerCloud Systems as hardware for
the CloudCommand service for 'cloud' based managment of large numbers
access points.
The CAP324 is a dual-band 802.11n wireless access point with 16MB flash
and 128MB RAM and single gigabit ethernet port. It can be powered via PoE
or a power adaptor.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47938
This patch adds support for Cisco's MR18.
Detailed instructions for the flashing the device can
be found in the OpenWrt forum thread:
<https://forum.openwrt.org/viewtopic.php?id=59248>
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
SVN-Revision: 47878
This is based on patches from Federico Fissore <f.fissore@arduino.cc>
especially this one:
7e2976fa83
The console is running with 250000 baud which is a non standard baud
rate and needs an extra patch to be applied, I will try to get this
patch upstream or something else which accomplish the same.
Some upstream code looks like there are many different versions of this
SoC, are these only internal versions and all versions on the consumer
market are the same? I saw different GPIO configuration and flash sizes
of 8MB and 16MB?
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47451
The international version is completely different from the already
supported Chinese version. The WLAN of the QCA956x SoC used by this router
has been fixed in r46948.
This patch looks like it changes a lot in
700-MIPS-ath79-openwrt-machines.patch; that is not the case. Unfortunately,
quilt decided to completely reorganize the Kconfig patch even though only
a single section has been added.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 47420
Antminers using the stock bootloader will not hash without this GPIO set.
Applies to DD and CC
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 47261
This patch fixes ticket #15267 by enabling power on the
WNR2200's USB port. At present, the USB port on the WNR2200
is non-functional due to it not receiving power.
This patch defines an additional GPIO pin, but none of the
current GPIO definitions have been modified.
Signed-off-by: Riley Baird <BM-2cVqnDuYbAU5do2DfJTrN7ZbAJ246S4XiX@bitmessage.ch>
SVN-Revision: 47236
This patch supersedes the v1 from September 17th.
Bumping the patch version - the MiniBox profile showed up under M, but
since it's called 'Gainstrong MiniBox v1.0' now it looks out of place.
Renamed the profile to gs-minibox-v1.mk to fix that.
The following patch adds support for the Gainstrong MiniBox into trunk
(or 'Designated Driver' :D ).
Fixed items:
- Inverted LED polarity (OOLITE seems to suffer from the same problem).
- Changed uppercase MINIBOX_V1_ prefix as requested.
- Prefixes are now gs_minibox_ similar to gs_oolite_ (same vendor).
- Mention the vendor (Gainstrong) in code headers.
Compiles fine, has been confirmed working by owners on 15.05.
Question: I've seen some boards use tools/firmware-utils/src/mktplinkfw.c,
the MiniBox images build fine without, so I'm wondering: do I need to add
it in there as well? Any added benefit?
Thank you
Signed-off by: Stijn Segers <francesco.borromini@inventati.org>
SVN-Revision: 47234
Sets the LEDs to boardname:color:led-name
Sets the LAN to eth0
Other corrections such as the Machine Name and HWIDs
v2 corrects the profile names in the Makefile and changes tabs to spaces
in the Makefile 'define Device/' like the other devices.
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 47221
Add support for WeIO board (http://we-io.net).
This board is based on Carambola2 board form 8Devices.
Signed-off-by: Drasko DRASKOVIC <drasko.draskovic@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org> [some cleanups]
SVN-Revision: 47036
QCA9563 and QCA9561 are two series of Qualcomm SoC Dragonfly. The only different
is QCA9563 w/o internal switch. It has one GMAC with SGMII interface. But they
have the same device ID(0x1150). So they share the same codes.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
SVN-Revision: 46971
This patch adds support for TP-LINK TL-WDR3320 v2.
This router uses a chinese version 2 firmware header,.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
SVN-Revision: 46934
This adds full support (sans sysupgrading from vendor firmware) for the COMFAST
CF-E316N v2 (aka CF-E316V2, CF-E316N-V2 and CF-E316Nv2.0, no FCC ID) by
Shenzhen Four Seas Global Link Network Technology Co., Ltd (this company is
actively refusing to provide GPL'd sources for the OpenWrt version they ship
with the device, damn them).
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
SVN-Revision: 46852
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
This patch adds support for TP-Link TL-WDR6500 v2.
The firmware has a U-Boot header for kernel, and a TP-LINK v2 header for
the whole firmware, so I have to create a new firmware creation method.
SVN-Revision: 46663
This patch adds support for the Onion Omega.
https://onion.io/omega
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Acked-by: Boken Lin <bl@onion.io>
Tested-by: Jacky Huang <huangfangcheng@163.com>
SVN-Revision: 46458
In fb6f62e97733312053ab593fcf68eea47a21169e several settings
are set on the ethernet device, but they are not working.
Fix Ethernet by setting the right values.
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
SVN-Revision: 46281
This patch adds support for the Cisco WAP4410N, an access point that uses the
AR9132 SoC. Web upgrades from stock are not yet possible, UART access required
for the initial flash.
Signed-off-by: Ryan A Young <rayoung@utexas.edu>
SVN-Revision: 46250
This patch adds support for the Bitmain Antminer S3 Cryptocurrency Miner
http://wiki.openwrt.org/toh/bitmain/s3
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 46236
The initialization routines for these boards were relying on some (wrong)
defaults for the QCA953x ethernet. Make these defaults explicit to prevent
breaking them when the QCA953x defaults are fixed.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 46206
The hardware should be almost the same as TL-WR720N-v3. WiFi and LAN networks
were tested by "Lo Yuk Fai <loyukfai@gmail.com>". Failsafe and slider switch
were tested by "Wong min <alpha080@gmail.com>".
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 46046
This patch adds support for the Bitmain Antminer S1 Cryptocurrency Miner
http://wiki.openwrt.org/toh/bitmain/s1
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Acked-by: James Hilliard <james.hilliard1@gmail.com>
SVN-Revision: 46044
AR8337 supports a configuration bit to swap MAC0 and MAC6.
Currently this is set in general if an AR8337 is detected and causes
issues with devices using an AR8334 (internally an AR8337, just
less chip pins).
And it might even cause issues with AR8337-based devices with
different board designs.
Swapping the MAC's however isn't needed for AR8337 in general.
It's just needed in case of certain board designs (affected devices
seem to be based on Atheros reference board AP135/136-010).
Therefore this configuration bit should be moved to platform data.
The patch includes the needed changes to the device initialization
code of affected devices. Hopefully I didn't miss any ..
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 45970
The mynet range extender hardware is suffering from ethernet
link loss when booting with a recent openwrt image. This only
happens on 100mbps links, with 1Gbps speed the link was fine.
The cause of the problem is that the AR8035 PHY (aka F1E)
requires turning on and off the special TX delay setting
depending on the speed of the link.
The 10mbps mode only needed the proper pll value, which was
extracted from the vendor code.
Reported-by: Pascal Paradis
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 45954
This patch is to add support for the Meraki MR12 and MR16 Access Points.
Currently everything is working, minus the 2nd NIC interface on the MR12
which is built into the SoC.
Signed-off-by: Chris R Blake <chrisrblake93 at gmail.com>
SVN-Revision: 45726
Users will now be provided with the inherent wifi toggle functionality
of /etc/rc.button/rfkill
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
SVN-Revision: 45635
Originally pressing a button would trigger a release state and vice-versa,
as observed from hotplug.d.
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
SVN-Revision: 45634
Most people report broken ethernet with upstream. Last year, user "franz.flasch"
authored a working mach-file. His patch is outdated so I modernized it. Original
patch and user commentary on page 1:
https://forum.openwrt.org/viewtopic.php?pid=260861#p260861
I have figured out what the critical differences are between the two that caused
upstream ethernet to break.
1) Both ath79_init_mac() functions calls must be invocated before any GMAC init
2) must init GMAC0 before GMAC1
That was enough to get upstream to function, but I wanted to enjoy my confidence
having tested franz's patch for a week sucessfully, so I put his whole
function in, which only features more differences in order of function calls.
An expert should consider these changes, which could pose potential bugs/issues:
1) No longer using the flag AR934X_ETH_CFG_SW_PHY_SWAP in the
ath79_setup_ar934x_eth_cfg() call.
2) Possible consequence of no longer explicitly setting ethernet duplex/speed.
Review: With this patch, my ethernet and wireless works.
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
SVN-Revision: 45633
It is common that the router provider be used rather than product name.
One can see this in target/linux/ar71xx/base-files/etc/uci-defaults/01_leds
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
SVN-Revision: 45630
It was reported that OM5P-AN needs not only a delay setting of 1 for RXD/RDV
but 2. These was found when testing with a NetGear GS752TP POE switch with a
cable length of 50ft and 250ft.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 45524
The ETH_RXDV_DELAY (17:16) and ETH_RXD_DELAY (15:14) are currently not cleared
by the function ath79_setup_ar934x_eth_cfg. Clearing these in the
ath79_setup_ar934x_eth_cfg may cause problems on some hardware because they
rely on the preset value by the bootloader.
Instead another function is introduced which also works on ETH_CFG on AR934x.
It can be used to safely clear and set ETH_RXDV_DELAY and ETH_RXD_DELAY on
machines which require special settings.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 45523
The tx/rx delay bits in the ETH_XMII_CONTROL register have to be unset when the
enable_rgmii_rx_delay/enable_rgmii_tx_delay will be set in the AT803x PHY.
Othwise the throughput in gigabit mode is heavily reduced.
Signed-off-by: Sven Eckelmann <sven@open-mesh.org>
SVN-Revision: 45521
The OM5P-AN boards are suffering from ethernet packet loss when booting with
some active POE setups or when switching to Fast Ethernet when previously
booted with Gigabit ethernet attached.
The cause of the problem is that the AR8035 PHYs requires special register
settings to work reliably on these boards. Enable the RGMII TX, RX delays and
disable SmartEE functionality of the AR8035 PHYs. Also enable the RXD and RDV
delay in the ETH_CFG register to fix the issue.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 45438
On newer Mikrotik boards, the radio calibration data
is stored differently and uses LZO compression instead
of RLE.
Update the RouterBOOT helper code to support the new
format.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 45297
While the switch positions aren't explicitly labeled as on and off, we've heard
complaints about them being wrong. This patch changes the handling to match the
stock firmware.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 44795
My previous patch regarding the Hornet-UB board
(commit: beed4d82d6a0154b0cd5f7b84e2180215ace6718) actually
causes the WPS led state to be inverted. Practically this meant
that value 0 in /sys/class/led/alfa:blue:wps/brightness would
turn the LED on and any positive value (1-255) would turn it off.
The above of course is confusing and hence reverting this value
back to the way it was before beed4d82d6a0154b0cd5f7b84e2180215ace6718.
Signed-off-by: Janne Cederberg <janne.cederberg@gmail.com>
SVN-Revision: 44791
This problem has existed at least since Attitude Adjustment and
is also present in trunk. Basically on the Hornet-UB board the
functionality of RESET and WPS have "switched places".
There are two tickets about the issue at dev.openwrt.org,
The solution suggested on them both is incomplete though
and introduces the following proglem:
Patching as suggested on #14136/#15282 will result in a situation
where simply pressing the RESET button on the bottom will cause
FACTORY RESET to be run. This is due to GPIO high/low state being
incorrect as a result of the above change and virtually the RESET
button is in the pressed-down state the entire time. When it is
then physically pressed, that causes the opposite, release, to be
triggered and since to the board it seemed that the button was
pressed long before it was released, the FACTORY RESET results.
The attached patch works as expected. I have verified both the
incorrect functionality as well as after fixing the issue as
described in the patch and flashing the resulting firmware to a
Hornet-UB board.
Signed-off-by: Janne Cederberg <janne.cederberg@gmail.com>
SVN-Revision: 44692
Previously, the generated images for the My Net Wi-fi Range Extender
wouldn't always work (and panic) due to the fixed mtd offsets and
sizes for the kernel and rootfs. This patch fixes the problem by
utilizing the shared Cybertan's partition parser to recalculate
the mtd partitions for every image dynamically everytime.
Reported-by: Pascal Paradis <peparadis@yahoo.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 44665
This patch renames the partition parser from
wrt160nl to more generic cybertan.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 44663
Please also backport to Barrier Breaker (this same patch applies there too).
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 44647
OpenWrt can be flashed with following uboot commands:
tftpboot 0x80500000 openwrt-ar71xx-generic-wpj558-16M-squashfs-sysupgrade.bin
erase 0x9f030000 +$filesize
cp.b $fileaddr 0x9f030000 $filesize
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 44620
This patch adds support for MERCURY MAC1200R, a dual band 802.11bgn + 802.11ac
router based on the AR9344, with QCA988x ath10k radio and 5 Fast Ethernet ports
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
SVN-Revision: 44359
This device is very similar to the TL-WR841N v8, only two LED GPIOs are
different.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 44255
The board is already supported by OpenWrt. WNR1000v2/WNR1000v2-VC are
pretty much the same as WNR2000v3/WNR612v2, therefore the same
initialization code and flash layout is used.
Signed-off-by: Ștefan Rusu <saltwaterc@gmail.com>
Tested-by: Douglas Fraser <1dsfraser@gmail.com>
SVN-Revision: 44221
Fix the WLAN MAC address to match the one printed on the label by using the
correct address from the ART instead of the address of the LAN interface.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 44183
This adds support for the TP-LINK CPE210/220/510/520 (Pharos series). These
devices are very similar to the Ubiquiti NanoStations, but with better specs:
faster CPU, more RAM, 2x2 MIMO.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 43385
This patch changes the code of the Wi-Fi On/Off button on the TP-Link WR1043ND v2
from KEY_WLAN to KEY_RFKILL (and renames a few constants to match). The reason
for this change is, that the KEY_WIFI button code is not recognized by the
hotplug subsystem. This means that the userspace is not notified about the
button being pressed which effectively renders it useless.
Signed-off-by: Josef Gajdusek <atx@atx.name>
SVN-Revision: 42922
This patch fixes LED definitions for the DRAGINO2 board.
1. It renames the Router/USB led to System, as it is now marked "SYS" on the board.
2. It gives control of the LAN and WAN leds and some other GPIOs to Linux.
3. It fixes the active_low property for the LAN and WAN leds.
4. It sets up WLAN, LAN and WAN leds in the UCI defaults.
5. It allows usage of the System led by the diag.sh script, so it will be used to indicate boot and failsafe status.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 42897
A typo in the definition for the OM2P reset button disabled its functionality
in OpenWrt. The actual button for these two devices is "1" and not "11".
Signed-off-by: Oren Poleg <oren@poleg.org>
[sven@open-mesh.org: added a commit subject+message]
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 42782
Qihoo 360 C301 is a dual band wireless router supports 802.11n and 802.11ac.
Its chipset is AR9344 + AR9882 with two 16MB flashes.
This patch adds its initial support.
v2:
* use mtd_get_mac_ascii to fetch MAC address for ath10k.
* use ath79_register_pci to initialize AR9882.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
SVN-Revision: 42552
While the AR9331 has a gigabit MAC towards the internal switch, the
integrated PHYs however are only 100-base-tx capable. The existing code
however advertieses gigabit capability in the link status word. If you
attach such a PHY to a gigabit capable switch on the remote end, with
some probability it attempts to negotiate gigabit and fails, falling
baco to the AR9331 assuming a 10mbit half-duplex link. This has been
observed quite frequently with the Carambola2 and gigabit capable
switches.
In ath79_register_eth(), "pdata->has_gbit = 1;" is set unconditionally
for both AR9331 ethernet ports. This is most likely wrong. Despite the
two MAC IP cores being gigabit MACs, the MAC for eth1 is connected to a
100base-T PHY via MII. The has_gbit attribute is used in the ethernet
driver to determine the supported link modes.
So either pdata->has_gbit is not set to 1 anymore, or the ethernet
driver needs to be modified to determine the advertised link code word
on another criteria than pdata->has_gbit. This patch implements the
former solution.
Signed-off-by: Harald Welte <laforge@gnumonks.org>
SVN-Revision: 42432
This sets the MAC address of the WLAN interface to the "official" primary MAC
address (the one on the label under the devices, and the one used with the stock
firmware). The MAC address used so far (primary-1) isn't even used at all with
the stock firmware, which sets (primary) on LAN and WLAN and (primary+1) on the
WAN interface (like OpenWrt does with this patch).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 42193
The OpenMesh MR600(v1) can only enable the 2.4G WiFi PHY LED through the
mini-PCIe device. Not configuring the LED pin inside the platform data
makes it impossible to configure it through any standard OpenWrt tool.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 42184
Change list:
* Remove button info on GPIO12, there is no button there.
* Remove nvram mtd partition, as it's not used for anything, saves 64k for user data.
Tested building for carambola2 target.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
SVN-Revision: 41993
this caused factory resets when reboot was pressed
Signed-off-by: Brent Thomson <brentthomson@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41932
Signed-off-by: Jon Suphammer <jon@suphammer.net>
Patchwork: http://patchwork.openwrt.org/patch/5838/
[juhosg:
- fix coding style,
- check the first and the last character of the MAC string
instead of using the strchr() function]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 41622
The GL-Connect GL.iNet v1 router is basically a TP-Link TL-WR703N with
more DRAM/Flash, 2x Ethernet ports and console/GPIO header in the same
small form-factor:
<http://www.gl-inet.com/w/?lang=en>
Moreover, the manufacturer is promoting the OpenWrt usage to replace
the original firmware and proposing patches against both AA and trunk:
<http://www.gl-inet.com/w/?p=398&lang=en>
This is a clean up of the original manufacturer GPLv2 patch by alzhao,
proposed to the list by Mark Janssen.
Signed-off-by: Michel Stempin <michel.stempin@wanadoo.fr>
Signed-off-by: Mark Janssen <mark@sig-io.nl>
Signed-off-by: alzhao <alzhao@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/5273/
[juhosg:
- remove user-space and image generation support, will be included
from other patches,
- fix coding style and drop superfluous comment in mach-gl-inet.c,
- rename and refresh kernel patch,
- adjust subject]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 41618
This patch adds support for the MikroTik RouterBOARD SXT Lite.
The new RB911L series is also supported as a result.
v2 of this patch fixes the wmac offset to match what is on the sticker.
v3 refreshes the patch against r41148 and defines the power led as the status led in diag.sh
v4 refreshes the patch against r41353 and fixes the patch path issue to make git am work correctly
v5 selects the kernel config option in the mikrotik profile rather than in the main ar71xx config
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41450
I added WIFI LED support (so now AP blinks nicely), I removed WPS
button GPIO (as it doesn't exist) and changed GPIO for reset button.
Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl>
SVN-Revision: 40976
This board manufactured by HiWiFi has the following features.
- Atheros 9331 SoC.
- 16MB flash and 64MB RAM.
- 4GB eMMC storage via SK6226 USB 2.0 controller.
- 2 LAN and 1 WAN ethernet ports with LEDs on them.
- 3 blue LEDs on the front panel.
- 1 button labeled as "reset".
- Powered by a USB cable.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 40973
Dlink dir-615-e1 can use dir-600-a1's image, but the image can't be
uploaded through dlink's normal firmware update web page.
Add profile for dir-615-e1 so the generated image can be uploaded
through the firmware update web page.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
SVN-Revision: 40969
The RB91x boards are suffering from ethernet packet loss after a cold
boot. The cause of the problem is that the AR8035 PHYs requires special
register settings to work reliably on these boards.
Enable the RGMII TX, RX delays and disable SmartEE functionality of
the AR8035 PHYs. Also enable the RXD delay in the ETH_CFG register
to fix the issue.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40509
With this patch OpenWRT supports the following on the ZyXEL NBG 6716:
-WiFi 2G (ath9k)
-WiFi 5G (ath10k)
-NAND flash
-2 Ethernet interfaces
-USB 2.0
-LEDs including switch
-reasonale defaults at first boot
Signed-off-by: André Valentin <avalentin@marcant.net>
Patchwork: http://patchwork.openwrt.org/patch/5101/
[juhosg:
- rename and refresh kernel patch,
- fix a few typos,
- change button key codes,
- use zyxel prefix in LED names]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40499
Apart from the wireless chip, the WNDR3700 v4 and the WNDR4300
is the same device. Indicate this in the kernel files.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40479
The 5V power of the USB is controlled by a GPIO pin of
the external WiFi chip. Setup the GPIO bitmasks in the
platform data of the WiFi chip to ensure that the 5V
power gets enabled by the ath9k driver.
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40478
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40477
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40475
The bootloader does not initializes the output function
correctly for all LEDs. DO that from the board setup code.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40474
The hardware manual says amber so change the color part of
the LED names to reflect that. Also update the constant names.
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40473
Everything seems to be working fine. Potential issues:
* VLAN port IDs are reversed with regard to the numbers on the case.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 40400
I don't have access to the specs, so I'm not sure about every detail, but I
haven't seen any problems with my test system, a TL-WR841N v9. It looks pretty
much like a QCA955x without PCI, a little twist in the clock calculation and
a AR9331-compatible switch.
Features not yet supported:
* EHCI (my test system doesn't have USB)
* ? (I have no idea if the QCA953x has any other features I don't know about
that aren't used by the TL-WR841N v9)
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 40399
Patch-by: Lars Bøgild Thomsen <lth@cow.dk>
Patchwork: http://patchwork.openwrt.org/patch/4922/
[juhosg:
- use a separate patch for kernel changes,
- reorder Kconfig and Makefile entries,
- change function and variable names to be lowercase only
and fix misaligned tabs in mach-gs-oolite.c,
... ]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40032
The flash address passed to rb_init_info() is bogus,
use the predefined AR71XX_SPI_BASE macro instead.
Compile tested only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39891
sizeof(array_from_function_definition) gives back the size of the pointer.
sizeof(type) * array_size should be used in memset.
Signed-off-by: David Völgyes <david.volgyes@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4950/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39890
The RB91x boards are using a serial shift register
connected to the SPI bus to drive some of the LEDs.
Rework the board setup code to register a SPI device
for that. This makes it possible to use the 'spi-74x164'
driver to control the device.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39703
I noticed that the patch at http://patchwork.openwrt.org/patch/4017/
for adding support for the MikroTik RouterBOARD 951Ui-2HnD had been
abandoned because it wasn't generated and sent to the mailing list
correctly and doesn't apply as a result. I have cleaned up this patch.
When testing this on real hardware, I also noticed that wireless didn't
work, so this patch fixes that as well.
This patch applies cleanly to SVN 39392.
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
Patchwork: http://patchwork.openwrt.org/patch/4773/
[juhosg:
- drop the 'rb951ui_wlan_init' function and rework the code to
use the recently introduced rb95x_wlan_init function instead,
- fix GPIO number of the port5 LED,
- rename LEDs according to the standard LED naming conventions,
and use 'rb' prefix in the names]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39641
On recent TL-WDR4300 boards the external LNAs of the 2.4GHz
interface are connected to GPIO lines. Because these GPIO
lines are disabled by default, the RX sensitivity of the
device is quite bad.
Setup the GPIOs of the external LNAs to fix the issue.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39392
The eth5 LED on the RB2011 is not working because the
LED control rule is missing. Fix it.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39335
The LNAs need to be enabled by setting their respective GPIO to high even
though the original firmware's setting sets them to low on initialization.
Obviously the LNAs are then later initialized by the driver on the OEM
firmware. Without this fix the device is mostly "deaf".
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Tested-by: Steven Haigh <netwiz@crc.id.au>
Patchwork: http://patchwork.openwrt.org/patch/4689/
[juhosg:
- remove the GPIO LED changes, the My Net N600 has no yellow LEDs at all,
- change subject and update the commit message]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39214
The LNAs need to be enabled by setting their respective GPIO to high even
though the original firmware's setting sets them to low on initialization.
Obviously the LNAs are then later initialized by the driver on the OEM
firmware. Without this fix the device is mostly "deaf".
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4688/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39213
The hardware supports large ethernet frames. Override
the maximum frame length and packet lenght mask in the
platform data to allow to use large MTU on the ethernet
interfaces.
Limit the feature to AR934x SoCs for now. It should work
on some other SoCs as well, but those has not been tested
yet.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39149
Now that the switch is working correctly I had the chance to actually
test the LED config.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4616/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39129
The bootloader on the WD My Net N750 disables the ports on it's internal
AR8327N switch by powering them down. The stock firmware then brings the
ports back up again by starting the auto negotiation process on each
port.
This fix implements just that.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4615/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39128
This enables us to add fixups to the board specific code for boards that
require special treatment of PHYs on mdio bus reset.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
http://patchwork.openwrt.org/patch/4614/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39127
This enables us to modify the ag71xx_mdio_platform_data from within the
board support files.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4613/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39126
It is only on RB911G-5HPnD and RB912UAG-5HPnD boards.
The LEDs and the USB port is not working yet.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39102
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
[juhosg: use a separate patch for kernel changes]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39077
The TL-WA801ND v2 board has only one LAN port which makes
it more similar to the TL-WR[78]50RE devices. Move the
board setup code into the mach-tl-wax50re.c file.
Based-on: http://patchwork.openwrt.org/patch/4506/
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39072
This way it is a bit easier to add other TP-LINK devices based on the
Atheros AP123 reference board with one LAN port.
Based-on: http://patchwork.openwrt.org/patch/4506/
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39071
Patch to add kernel support for the TP-LINK WA801ND v2
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Patchwork: http://patchwork.openwrt.org/patch/4500/
[juhosg:
- the TL-WA801ND v2 does not have a sliding switch, it uses a push button
for WPS instead. Use the tl_mr3420v2_gpio_keys array to reflect that,
- rename kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39063
This patch improves support for the device considerably.
1. The wifi didn't work in the initial release. This was because
the WMAC of the AR9340 is not connected to the antennas.
(However, it can pick up wifi signals, if they are strong enough!)
Instead there's a dedicated AR9300 chip on the same board, which
works.
2. Ethernet throughput is improved. iperf shows that the hardware
can sustain more than 200Mbit/s and no longer drops any packages
when the link is under load.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Patchwork: http://patchwork.openwrt.org/patch/4461/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38949
Just a small oversight my part, added the support for the USB led
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4425/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38946
Patch to add kernel support for the TP-LINK WA750RE and the WA850RE
range extender
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
[juhosg: rename and refresh kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38717
This patch adds a new device definition for a
Western Digital device. The hardware seems to
be based on Qualcomm Atheros DB120 design.
Patchwork: http://patchwork.openwrt.org/patch/4281/
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
[juhosg: refresh kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38686
BXU2000n-2 A1 is a BHU Networks WLAN board, use ar9341 chip.
Patchwork: http://patchwork.openwrt.org/patch/4183/
Signed-off-by: Terry Yang <yangbo@bhunetworks.com>
[juhosg:
- rename and refresh kernel patch,
- fix some checkpatch warnings and adjust whitespaces in
mach-bhu-bxu2000n2-a.c]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38591
This patch adds support for DRAGINO2 board (used by
Meshpotato v2). Most of the files included can be
found in the official svn repository provided by the
company [1]. I have just adapt it to the last OpenWrt
trunk revision (Fri Oct 4 10:49:47 2013).
1. http://svn.dragino.com/dragino2
Patchwork: http://patchwork.openwrt.org/patch/4234/
Signed-off-by: Pau Escrich <p4u@dabax.net>
[juhosg:
- rename and refresh kernel patch,
- fix checkpatch warnings in mach-dragino2.c]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38587
Fixes the 5 GHz LED.
The same function has no effect on the 2.4 GHz LED at all, so we might
as well remove it.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38482
This patch adds support for the hardware slide switch on
the TL-MR3040 v2.
Signed-off-by: Mads Hansen <d@taba.se>
[juhosg: use EV_SW instead of EV_KEY]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38190
This patch
- changes the color names from orange to amber
- changes the name of GPIO 13 from WIFI_BGN (wifi_bgn) to WLAN_2G
(wlan2g) to be more consistent with the other routers' files
- changes the descriptions of the hardware keys to be a tad more
explicit
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Patchwork: http://patchwork.openwrt.org/patch/4081/
[juhosg: update the LED migration script as well]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38105
Enable GPIO 20. This hands off control of the blue planet led to the
integrated switch. Consequently, remove the led configuration for the
blue planet led.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Patchwork: http://patchwork.openwrt.org/patch/4080/
[juhosg: whitespace fixup]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38096
This patches fixes the lan led configuration. The new configuration is
identical to the one in mach-db120.c and it works. The previous one
didn't work at all.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38094
Rename the function and extend it in order to make it
usable from board setup code.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38085
This patch adds support for TP-Link TL-MR13U router with built-in 10AH
rechargeable battery.
The patch is based on kamwanlai's patch:
https://forum.openwrt.org/viewtopic.php?pid=206746#p206746
Updated to accommodate recent changes introduced with:
ar71xx: remove fs_* variables from image/Makefile
Signed-off-by: Oleg Titov <oleg.titov@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4063/
[juhosg:
- refresh and rename rename 930-add-tl-mr13u-support.patch =>
625-MIPS-ath79-add-tl-mr13u-support.patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38063
This patch adds OpenWRT support for the Netgear WNR2200 (N300)
wireless router with USB.
Technical details of this router can be found at
http://www.netgear.com/home/products/wirelessrouters/work-and-play/WNR2200.aspx
and http://wikidevi.com/wiki/Netgear_WNR2200
Signed-off-by: Aidan Kissane <aidankissane@googlemail.com>
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
Patchwork: http://patchwork.openwrt.org/patch/4055/
[juhosg:
- add commit message and SoB line from the original patch
- remove dead code from mach-wnr2200.c
- refresh 624-MIPS-ath79-WNR2200-support.patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38059
I checked the GPL code drop from D-Link and tried to get the wireless
and LAN switch LEDs to light up. I found some references in
AthSDK/www/DIR-825_C1/bsp.h as well as
AthSDK/www/DIR-825_C1/rootfs/etc/sysconfig/S2gpio.sh, but in the end I
only got the led for 2.4GHz to work. Anyway, here's the patch.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37963
Apparently registering usb device on newest trunk causes
this AP not to boot...
Since there is no USB socket in that device anyway this
can be simply removed (and device boots then no problem).
[juhosg:
- tweak subject line and description,
- remove #include "dev-usb.h",
- remove 'select ATH79_DEV_USB' from Kconfig]
Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37844
This patch fixes the code of the buttons for TP-Link WA901ND.
Signed-off-by: Rocco Folino <lordzen@autistici.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37696
Small router sold in EU: AR9330@400MHz, 1x USB2.0,
2x ethernet, 8MB flash, 32MB ram, one led, one button.
See: http://galeria.tech-blog.pl/TP-Link_TL-WR710N-EU/
[juhosg: use a separate kernel patch]
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3873/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37572
Looks like trunk@37090 has changed the logic that determines
if router's button was pressed. This resulted in TEW632BRP
always booting into failsafe mode because it detected pressed
button (which was not pressed).
Measure with voltmeter has shown that buttons on this router
are actually active-low. This patch reflects this fact in
board configuration and fixes 'load info failsafe mode' issue.
Note: it looks like Trendnet TEW632BRP and a close relative
to TEW-652BRP V1.0 and D-Link DIR-615C1, so same problem may
exist on those routers as well. This patch doesn't affect
routers other than 632BRP and unfortunately I do not have
hardware to test this issue with other routers.
This patch fixes#13893 and is tested on actuall Trendnet
TEW632BRP.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37569
switch buttons should be declared as switch so the failsafe shell is not
triggered by accident in procd
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 37131
The TP-LINK TL-MR3220 v2 has a button on the left side
labeled "WIFI". This is GPIO 24. This patch adds the
support for this button.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36848
The port 6 of the switch is connected to the SFP
cage on the RB2011*S boards. Add a helper function
to correctly initialize the switch configuration
data on those boards to make the SFP port usable.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36799
Here is corrected version (only thing not working are wifi LEDs).
[juhosg: this has been created from the following patch:
http://patchwork.openwrt.org/patch/3620/ ]
Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36578
Network connectivity works fine (LAN and WAN).
For GPIOs, only pwr led and the green wan leds are supported for now.
Signed-off-by: Mathieu Olivari <mathieu.olivari@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36459
Add support for TPLINK WR720N v3 which has 4MB flash,
32MB ram, 2 ethernet interfaces, 1 USB 2.0 port.
The patch is mostly a modification from mach-tl-wr703n.c.
GPIO numbers for the slider switch is from mach-tl-mr3020n.c.
Tested on my device and they worked fine.
Signed-off-by: yousong <yszhou4tech@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36456
Use eeprom (art) from included wifi card, not hard coded in flash.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36037
Error in using another MDIO (AP123 platform using only one GE1 device
for eth0 and eth1) for the router mr3420v2.
?onfirmed: https://forum.openwrt.org/viewtopic.php?pid=194779#p194779
Routers in this sense are the same and the only difference is: USB
port, USB led, instead of the GPIO-switch we have GPIO-button.
Signed-off-by: Dmytro <dioptimizer@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36036
[juhosg: use gpio_request_one to enable the USB power]
Patch-by: Dmytro <dioptimizer@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@opewrt.org>
SVN-Revision: 35961
LAN1 and LAN2 LEDs not present (it pulled to ground via
resistors) on MR3040 and MR11U devices. This little patch
enabling ability to control GPIO14 and GPIO15.
Patch-by: Dmytro <dioptimizer@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3439/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35960
[juhosg:
- remove custom mdio bus info and platform data for ar8327, clear the
.led_cfg field from dir835a1_setup instead,
- remove arguments of dir835c1_generic_setup function, register the
LEDs directly from the board specific setup instead]
Signed-off-by: Alexander Stadler <sa.maillists@univie.ac.at>
Patchwork: http://patchwork.openwrt.org/patch/3426/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35957
Use the same MAC addresses as the original firmware.
Based on a patch from #10421.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Tested-by: Gabor Varga <vargagab@gmail.com>
SVN-Revision: 35730
This is platform definition for the RB951G device. It's mostly rework
of RB2011UAS patchset with network taken from the RB751 patches.
The main difference is the flash layout used by this device.
[juhosg:
- remove dead code from mach-rb951g
- add "-2HnD" suffix to the machine name
- use a separate 615-MIPS-ath79-RB951G-support.patch]
Patchwork: http://patchwork.openwrt.org/patch/3257/
Signed-off-by: Kamil Trzcinski <ayufan@ayufan.eu>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35633
We utilize many Routerboard 751's and discovered that our latest batch
of RB751's would not initialize the wireless radio. We have determined
Mikrotik has changed where the mac address was located inside hardconfig.
As such we utilize "routerboot_find_tag" to find the location of the mac
address. We should remove "RB751_MAC_ADDRESS_OFFSET" as it is ambiguous
by machine manufacturing date. The newer batch of RB751's that we received
had a RB751_MAC_ADDRESS_OFFSET 0x10.
Signed-off-by: Davey Hutchison <dhutchison@bluemesh.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35519
WDR3500 is similar to WDR3600 except it doesn't have gigabit ethernet,
and has only 1 USB port.
Pending issues:
* Leds are not working at all (except power and wlan_5g)
* LAN switch ethernet ports are reversed with respect to case label.
[Label] -> soft device
[LAN1] -> eth0.4
[LAN2] -> eth0.3
[LAN3] -> eth0.2
[LAN4] -> eth0.1
Based on http://patchwork.openwrt.org/patch/3208/
Thanks-to: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Gui Iribarren <gui@altermundi.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35423
[juhosg:
- remove unused GPIO stuff
- use a separate kernel patch for machine integration]
Signed-off-by: Alexander Stadler <sa.maillists@univie.ac.at>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35401
The PHY_SWAP and PHY_ADDR_SWAP bits are initialized
differently by different versions of the bootloader.
This leads to broken ethernet connection with OpenWrt
on some boards.
Turn both SWAP bits OFF on these boards to make it
consistent regardless of the bootloader used.
Based on a patch by Michel Stempin <michel.stempin@wanadoo.fr>.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35037
Based on the following patch:
http://patchwork.openwrt.org/patch/3043/
[juhosg:
- remove custom LED and button arrays
- use separate machine specific patch
- update Kconfig]
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34779
It is mostly the same as TL-WA901N. WLAN and LAN
are working. LAN LED is working. WLAN signal
strength LEDs are not working yet.
http://wiki.openwrt.org/toh/tp-link/tl-wa7510n?s[]=wa7510n
[juhosg:
- cleanup commit message
- move non kernel related stuff into separate changes
- rename and refresh 615-MIPS-ath79-TL-WA7510N-v1-support patch
- merge WA7510N support into the mach-tl-wa901nd.c file
- add 3.6 support]
Signed-off-by: Stefan Helmert <helst_listen@aol.de>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34187
According to #12421, GPIO 1 controls the power
output on the unused lines of the LAN2 port.
Remove the LED definition in order to prevent
possible permanent hardware damage.
If someone needs that, the power-out feature can
be controlled via the GPIO sysfs interface.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34076
This patch adds preliminary support for the Mikrotik RB2011L.
The NAND flash is not yet supported, so only the initramfs
kernel can be used for now.
[juhosg: remove unnecessary PCI/USB related stuff, the board
does not use that, update commit message]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
SVN-Revision: 33344
