This can be used to configure the base mac address from which all
interface mac addresses are derived
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 00860e485b)
Simplifies setting ifname to a different pattern for all affected
interfaces.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit a9ff3ba24b)
When the reset button is next to the SFP cages, I2C operations on the
modules might cause interference on the button's GPIO line. Add a
debounce-interval of 5 times the poll-interval to ensure the line is
actually stable for some time and not just glitching.
This squashes commit 4357f32d41 ("realtek: debounce reset key for
Zyxel GS1900") and commit 777c6106ed ("realtek: move debounce-interval
to correct node").
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Without this patch, we get the following error:
Mon Dec 23 11:35:44 2024 daemon.err hostapd: nl80211: kernel reports: integer out of range
As updating hostapd would be too complex and requires further testing,
we backport this simple upstream fix instead.
Fixes: https://github.com/openwrt/openwrt/issues/16680
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Link: https://github.com/openwrt/openwrt/pull/17590
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 5ce1af9539)
Link: https://github.com/openwrt/openwrt/pull/17591
Signed-off-by: Robert Marko <robimarko@gmail.com>
Due to "SIM present" input defaulting to "button" type, it is
interpreted as such when booting, and causes the system to enter
failsafe, if the tray is missing. Similarly to rfkill switch on
TP-Link WDR4300 and Archer C7, make it EV_SW instead, to stop it from
interfering with the boot process.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17503
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 7b9ca01109)
It's missing a hyphen present in every other LED from the set. Set it to
"green:signal-strength-4".
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17503
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit d04f41e092)
OpenWRT on the WNDAP6x0 refuses to sysupgrade to itself
due to a compat_version imbalance. The Image is generated
with version 2.0, but the uci-defaults says that it needs
to be at 3.0 for the device.
Fix this by downgrading WNDAP6x0 05_fix-compat-version's
values back to 2.0 so it matches what we use.
Fixes: 5815884c3a ("apm821xx: migrate to DSA")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit e9415be4ad)
Subtarget xrx200_legacy supports only a few devices. They all use
the integrated Lantiq GSWIP switch and lantiq xway PHYs. The atheros
and icplus PHYs can be safely disabled.
Switches used by individual devices are listed below.
Device Switch PHY
Alpha ASL56026 Lantiq GSWIP int. switch
Arcadyan VG3503J Lantiq GSWIP int. switch
Netgear DM200 Lantiq GSWIP int. switch
TP-LINK TD-W8970 Lantiq GSWIP Lantiq PEF7071V
TP-Link TD-W8980 Lantiq GSWIP Lantiq PEF7071V
Reduces uncompressed kernel size by 16 kB.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/17581
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 517b9c1cdc)
This was done by executing these command:
$ make kernel_oldconfig CONFIG_TARGET=subtarget
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/17581
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 524e22b4c7)
The Plusnet Hub One and BT Business Hub 5A have the same hardware as
the BT Home Hub 5A. This commit adds alternative names so that both
devices can be easily found in the firmware selector.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/17583
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 1b045a7c13)
The TP-Link TD-W9980(B) shares the same hardware with the TP-Link TD-W8980.
The only difference is that the TD-W8980 does not support VDSL. This is a
software limitation and once the software is changed, both work equally
supporting VDSL. This commit adds alternative names for devices so they
can be easily found in the firmware selector.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/17583
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit b2b4ce1532)
This setting is more suitable for device running OpenWRT.
Most OpenWRT targets are already default to this configuration,
and it has shown better performance in VPN (wireguard).
Fix: #17454
Signed-off-by: Kien Truong <duckientruong@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17575
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 1c178f3644)
Refresh DTS with required changes for cpufreq, MTD and MMC. While at it
also fix wrong speed for MAC.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 17b0d1379a)
Replace cpufreq patch with new version requested upstream.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 5069557350)
Add pending patch for ETS qdisc on Airoha ethernet driver.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 53bc763331)
Add patch fixing support for MMC. Additional clock are needed for MMC to
work and some small fixup to make the Mediatek MMC driver on Airoha SoC.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit be5a9ff24b)
Backport patch to support ETS and HTB scheduler for airoha ethernet
driver.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 3ec3ea5316)
Replace BUS clock patch with upstream version with related tag
as it got approved and merged.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 07b49ce876)
Enable MMC and PCI config symbol and refresh config for Airoha AN7581.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 73d368868c)
Two use AR9287 and one AR9381. Both have different calibration sizes.
Move differences out of wifi node to make it clearer what's what.
qca,no-eeprom needs to stay for 7362sl as there's no nvmem equivalent
for caldata_extract_reverse
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17278
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/17512
Signed-off-by: Robert Marko <robimarko@gmail.com>
These units use AR9287, which has a calibration size of 3d8.
Also fixed compatible string to the proper one to indicate AR9287.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17278
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/17512
Signed-off-by: Robert Marko <robimarko@gmail.com>
The label MAC address is written inside the case of the whw03 v2 at the bottom.
Similar fix as to the 4040 in b22d382ae4
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Link: https://github.com/openwrt/openwrt/pull/17535
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit c113982706)
Updating the driver patches for ipq40xx (correctly) removed the
ethernet0 alias from qcom-ipq4019.dtsi; however, on some devices this
alias is needed for the bootloader to set MAC addresses in the FDT.
As it is unknown which devices actually need the alias, simply add it to
all devices trees for now that enable the &gmac now to avoid regressions
from previous OpenWrt releases. The additional alias should not cause any
issues even when it is not needed.
A TODO comment is added to the same Device Trees to document that the
alias may not be needed (hopefully preventing it from being copied
unnecessarily to newly added devices in the future). The following
devices are known to need the alias for correct MAC address assignment,
so no TODO comment is added:
- FRITZ!Box 4040
- FRITZ!Box 7530
Fixes: cd9c721124 ("ipq40xx: 6.1: use latest DSA and ethernet patches")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Link: https://github.com/openwrt/openwrt/pull/17442
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit d09dd75fbd)
This patch is needed on bmips since it fixes issues with GPIOs not being
properly configured due to gpio_request_enable not being called on bcm63xx
devices. Therefore we can now drop the bcm63268 gpio function patch.
Backported from f5b1d340be with the exception of
the realtek patch removal.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit f5b1d340be)
Basic rates were not set for mesh-interfaces, resulting in the undesired
behavior where 11s frames might be sent with a rate which was not
configured.
Depending on the driver, the basic rate might also be used to determine
the beacon rate configured to the chip. One such example are MediaTek
MT7915 platforms.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 3ec7f3a512)
According to datasheet, on AR9344 the switch and switch analog need to
be reset first before initiating a full reset.
Resetting these systems fixes spurious reset hangs on Atheros AR9344
SoCs.
Link: https://github.com/freifunk-gluon/gluon/issues/2904
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 916af73fc3)
Hardware:
SoC: MT7981b
RAM: 512 MB
Flash: 256 MB SPI NAND
Ethernet:
1x2.5Gbps (rtl8221b)
WiFi: 2x2 MT7981
Button: Reset
LED: 1x multicolor
Installation
------------
At the moment, firmware installation is only possible via a transition firmware.
It's can be requested from the manufacturer by email to support@cudy.com
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17225
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 6992d6e51a)
I think I implemented the U-Boot handling incorrectly on M30 (saw the issue while porting M60 to OpenWrt). Maybe someone with more U-Boot experience can have a look at it.
What I understood until now:
Before flashing, `sw_tryactive` must be set to 0 because OpenWrt runs on partition 0
During reset after flashing, U-Boot executes the following line:
`boot_rd_auto_sw_img=if itest.s ${sw_tryactive} == 2; then run boot_by_part; else run boot_by_tryactive; fi`
As `sw_tryactive` was set to 0 before flashing, `boot_by_tryactive` will be executed:
`boot_by_tryactive=if itest.s ${sw_tryactive} == 0; then setenv sw_tryactive 2; setenv sw_active 1; saveenv; run ub0; else setenv sw_tryactive 2; setenv sw_active 2; saveenv; run ub1; fi`
As `sw_tryactive` was set to 0 before flashing, `sw_active` will be set to 1 and `ub0` will be executed:
`ub0=setenv bootpart 0; mtkboardboot; run ub0to1; uip main; reset`
If the OpenWrt boot is successful, `ub0to1` and `uip` main will never be executed. Only in case OpenWrt cannot be loaded, `mtkboardboot` will return and the fallback `ub0to1` is executed.
Conclusion: It's sufficient to set `sw_tryacitve` to 0 before flashing, the added code in `target/linux/mediatek/filogic/base-files/etc/init.d/bootcount` is useless.
In the worst case (/proc/cmdline doesn't contain `bootpart=ubi0` as expected), the bootpart variable would be set to 1 and causes starting the firmware from the second partition instead of the one on the first partition.
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17298
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 70610a5240)
Images for certain devices are staring to become too large, as some
device only have 6MB available in their vendor partition layout for the
initial install. This is especially pressing for bootloaders only
supporting gzip compression.
Drop some packages from DEFAULT_PACKAGES that aren't strictly required
for a factory install. The user can always install more packages later
using opkg/apk, or via a sysupgrade to a custom build.
firewall4 is kept to ensure the most recent firewall package is selected
in builds including LuCI.
ethtool is kept as a frequently used diagnostics tool.
Link: https://github.com/openwrt/openwrt/pull/17450
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit c9ae39b2d1)
We can use a package for the MV88E6060 DSA switch on the single
ath79 device that uses it, saving around 600 KB of memory on
all other devices (for the DSA infrastructure, mainly).
As far as I can see the TP-Link TL WR941 v2 is the only device
using MV88E6060 and the only device with a DSA switch overall.
However the ath79 people should look at this so I'm not
mistaken.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250102-ath79-mv88e6060-module-v1-1-c2a8e31e72fc@linaro.org/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit e7419381fd)
Just one of the devices uses the Marvell MV88E6060 DSA
switch so break this out from the generic kernel config
and into a package selected only by that single device
and probed at boot instead.
The big win is from being able to drop the dsa_core
(~600KB) kernel module out of the common kernel on
devices with no DSA switch.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
(cherry picked from commit 2456a2fd7f)
On the AVM 5490/5491, lan1, lan2 and wan ports are connected directly
to the internal GSWIP switch. The lan3 and lan4 ports are connected via
an external QCA8334 switch. This commit adds the missing entries in dts
and adds the driver module.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/17473
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 14be320291)
