This patch adds support solely for version 1 of the TP-Link WR802N.
It is based on Rick Pannen's patch posted on the OpenWrt devel list.
Signed-off-by: Julius Schulz-Zander <julius@inet.tu-berlin.de>
This patch adds support for the Airtight C-60.
SOC: Atheros AR9344 rev 2 (CPU:560.000MHz)
RAM: 128 MiB
NOR: MX25L3205D 4MiB
NAND: ST Micro NAND 32MiB 3,3V 8-bit
SW-NET: AR8327N (2 Ports)
WLAN1: Dual-Band AR9340 Rev:2 (built-in SoC)
WLAN2: Dual-Band AR9300 Rev:4 PCIe Chip
The switch is setup for an accesspoint:
LAN1: (gigabit) is the wan-port.
LAN2: (fast ethernet) is bridged with the br-lan.
Flashing Guide (via initramfs):
1. Connect a PC to the serial port of the C-60.
power up the C-60.
Enter u-boot command prompt:
#> nand erase
#> setenv bootcmd "bootm 0x9f060000"
#> saveenv
#> setenv ipaddr 192.168.1.1
#> setenv netmask 255.255.255.0
#> setenv serverip 192.168.1.100
#> setenv bootfile lede-ar71xx-nand-c-60-initramfs-kernel.bin
#> tftpboot
#> bootm
2. Wait for the C-60 to boot LEDE.
On the root prompt. Enter:
# ubiformat /dev/mtd4
# ubiattach -p /dev/mtd4
3. After that copy the sysupgrade.tar onto the router and run:
# sysupgrade sysupgrade.tar
to flash the image.
Special thanks to Chris Blake <chrisrblake93@gmail.com>. He provided
a C-60 unit and he helped with debugging the switch, LEDs and platfrom
support.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds support for Cisco's Z1.
Detailed instructions for the flashing the device can
be found in the OpenWrt wiki:
<https://wiki.openwrt.org/toh/meraki/z1>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Zbtlink ZBT-WE1526 is based on Qualcomm Atheros QCA9531 v2.
Short specification:
- 650/400/200 MHz (CPU/DDR/AHB)
- 5x 10/100 Mbps Ethernet
- 1x USB 2.0
- 128 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, up to 22 dBm
- two external, non-detachable antennas
- 8x LED, 1x button
- UART header (pinout: VCC, RX, TX, GND)
Flash instruction:
Use sysupgrade in vendor firmare which is based on OpenWrt.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
jjPlus JWAP230 is based on Qualcomm Atheros QCA9558 + QCA8337.
Short specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 2x 10/100/1000 Mbps Ethernet
- 128 MB of RAM (DDR2)
- 16 MB of FLASH
- 3T3R 2.4 GHz with external PA (SST12LP15A), up to 28 dBm
- 3x MMCX connectors
- power input: 802.3at PoE or wide range DC (36-57 V)
- optional 802.3af PSE
- 1x mini-PCIe connector with PCIe, USB buses and SIM slot
- 1x mini-PCIe connector with PCIe bus
- 1x USB type-A connector
- 6x LED, 1x button (hardware reset)
- RS232 (MAX3223) and (E)JTAG headers
Default configuration:
- WAN on eth1 (RJ45 near LEDs with PoE input)
- LAN on eth0 (RJ45 near DC jack)
- left top LED set to be status LED
- all LEDs configurable form user space
Flash instruction (do it under U-Boot, using RS232):
1. tftp 0x80060000 lede-ar71xx-generic-jwap230-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Wallys DR531 is based on Qualcomm Atheros QCA9531 v2.
Short specification:
- 550/400/200 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz with external PA (SE2576L), up to 30 dBm
- 2x MMCX connectors
- mini-PCIe connector with PCIe/USB buses and SIM slot
- 7x LED, 1x button, 1x optional buzzer
- UART, (E)JTAG and LED headers
Default configuration:
- WAN on eth1 (RJ45 near DC jack)
- LAN on eth0 (RJ45 near button)
- S4 LED set to be status LED
- all LEDs configurable form user space
- button configured for reset
Flash instruction (do it under U-Boot, using UART):
1. tftp 0x80060000 lede-ar71xx-generic-dr531-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This patch adds the target profile SOM9331 and configures hardware
functionality for the 3x Eth Ports & corresponding LED's, the USB Host,
the USART to USB bridge and the System LED.
Signed-off-by: Allan Nick Pedrana <nik9993@gmail.com>
The CE image format used by OpenMesh can contain extra blocks which
are not used for flashing. Only the first three embedded images
(fwupgrade.cfg, kernel, rootfs) are required in this order to successfully
flash an image via sysupgrade. All extra embedded images should be ignored
for the available devices.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
The platform_check_image_openmesh function used break statements to signal
that the board name matched the image target. This worked because the
sysupgrade binary checked the image inside a loop. The break statement
stopped the loop and skipped any additional check.
Instead the check should be done without such sideeffects by simply
combining the board names and image targets. Only a mismatch should cause a
negative result for the caller and skipping of the additional checks.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
- CPU QCA9531-BL3A
- RAM: 64MB
- flash: 16MB
- USB
AP143 platform, similar to tl-wr841n v10/v11, but with USB
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
To avoid confusion with different unifiac devices, rename existing target
"unifiac" to "unifiac-lite", before "unifiac-pro" is introduced.
Signed-off-by: P.Wassi <p.wassi at gmx.at>
OpenWrt can be flashed with following uboot commands:
tftpboot 0x80500000 openwrt-ar71xx-generic-wpj342-16M-squashfs-sysupgrade.bin
erase 0x9f030000 +$filesize
cp.b $fileaddr 0x9f030000 $filesize
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
SVN-Revision: 49157
There's no reason for us to be more lenient than the stock firmware, so
better check the HWREV as well to avoid bricked devices.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 49105
This patch adds support for the Bitmain Antrouter R1
http://wiki.openwrt.org/toh/bitmain/r1
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 48058
OpenWrt configuration part of support for the PowerCloud Systems
CR5000. The CR5000 is a dual-band 802.11n wireless router with
8MB flash, 64MB RAM, (unused on stock firmware) USB 2.0 port and
five port gigabit ethernet switch. The CR5000 was sold as
hardware for the Skydog cloud-managed router service.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47946
OpenWRt configuration part of support for the PowerCloud
Systems CR3000. The CR3000 is a 802.11n 2.4 GHz wireless router with
8MB flash, 64MB RAM, a four port gigabit ethernet switch, and a fast
ethernet wan port that was sold by PowerCloud Systems as
hardware for the Skydog cloud-managed router service.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47945
Openwrt configuration part of support for PowerCloud CAP324
Cloud AP. The CAP324 Cloud AP is a device sold by PowerCloud Systems
who's stock firmware (CloudCommand) provides 'cloud' based managment
of large numbers access points.
The CAP324 is a dual-band 802.11n wireless access point with 16MB flash
and 128MB RAM and single gigabit ethernet port. It can be powered via PoE
or a wall wart.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47944
This patch adds support for Cisco's MR18.
Detailed instructions for the flashing the device can
be found in the OpenWrt forum thread:
<https://forum.openwrt.org/viewtopic.php?id=59248>
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
SVN-Revision: 47878
This is based on patches from Federico Fissore <f.fissore@arduino.cc>
especially this one:
7e2976fa83
The console is running with 250000 baud which is a non standard baud
rate and needs an extra patch to be applied, I will try to get this
patch upstream or something else which accomplish the same.
Some upstream code looks like there are many different versions of this
SoC, are these only internal versions and all versions on the consumer
market are the same? I saw different GPIO configuration and flash sizes
of 8MB and 16MB?
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47451
The international version is completely different from the already
supported Chinese version. The WLAN of the QCA956x SoC used by this router
has been fixed in r46948.
This patch looks like it changes a lot in
700-MIPS-ath79-openwrt-machines.patch; that is not the case. Unfortunately,
quilt decided to completely reorganize the Kconfig patch even though only
a single section has been added.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 47420
This patch supersedes the v1 from September 17th.
Bumping the patch version - the MiniBox profile showed up under M, but
since it's called 'Gainstrong MiniBox v1.0' now it looks out of place.
Renamed the profile to gs-minibox-v1.mk to fix that.
The following patch adds support for the Gainstrong MiniBox into trunk
(or 'Designated Driver' :D ).
Fixed items:
- Inverted LED polarity (OOLITE seems to suffer from the same problem).
- Changed uppercase MINIBOX_V1_ prefix as requested.
- Prefixes are now gs_minibox_ similar to gs_oolite_ (same vendor).
- Mention the vendor (Gainstrong) in code headers.
Compiles fine, has been confirmed working by owners on 15.05.
Question: I've seen some boards use tools/firmware-utils/src/mktplinkfw.c,
the MiniBox images build fine without, so I'm wondering: do I need to add
it in there as well? Any added benefit?
Thank you
Signed-off by: Stijn Segers <francesco.borromini@inventati.org>
SVN-Revision: 47234
Add support for WeIO board (http://we-io.net).
This board is based on Carambola2 board form 8Devices.
Signed-off-by: Drasko DRASKOVIC <drasko.draskovic@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org> [some cleanups]
SVN-Revision: 47036
This patch adds kernel and userspace support for the Ubiquiti Networks airGateway Pro.
Signed-off-by: Matthew Reeve <mreeve at tenxnetworks.com>
SVN-Revision: 46961
This patch adds support for TP-LINK TL-WDR3320 v2.
This router uses a chinese version 2 firmware header,.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
SVN-Revision: 46934
This adds full support (sans sysupgrading from vendor firmware) for the COMFAST
CF-E316N v2 (aka CF-E316V2, CF-E316N-V2 and CF-E316Nv2.0, no FCC ID) by
Shenzhen Four Seas Global Link Network Technology Co., Ltd (this company is
actively refusing to provide GPL'd sources for the OpenWrt version they ship
with the device, damn them).
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
SVN-Revision: 46852
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
This patch adds support for TP-Link TL-WDR6500 v2.
The firmware has a U-Boot header for kernel, and a TP-LINK v2 header for
the whole firmware, so I have to create a new firmware creation method.
SVN-Revision: 46663
This patch adds support for the Onion Omega.
https://onion.io/omega
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Acked-by: Boken Lin <bl@onion.io>
Tested-by: Jacky Huang <huangfangcheng@163.com>
SVN-Revision: 46458
This patch adds support for the Cisco WAP4410N, an access point that uses the
AR9132 SoC. Web upgrades from stock are not yet possible, UART access required
for the initial flash.
Signed-off-by: Ryan A Young <rayoung@utexas.edu>
SVN-Revision: 46250
This patch adds support for the Bitmain Antminer S3 Cryptocurrency Miner
http://wiki.openwrt.org/toh/bitmain/s3
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 46236
rocket-m titanium is a device based on ar9344 with 802.11af poe.
It doesn't use the SoC wifi, instead it's using an ar9280 connected to
the pci bus. The gps version of the rocket-m ti is working, but
gps is untested. The gps is connected to the first serial port.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 46234
This patch is to add support for the Meraki MR12 and MR16 Access Points.
Currently everything is working, minus the 2nd NIC interface on the MR12
which is built into the SoC.
Signed-off-by: Chris R Blake <chrisrblake93 at gmail.com>
SVN-Revision: 45726
This patch adds support for the XW version of the Rocket M series devices
manufactured by Ubiquiti, based on the Atheros AR9342 SoC.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
SVN-Revision: 45553
OpenWrt can be flashed with following uboot commands:
tftpboot 0x80500000 openwrt-ar71xx-generic-wpj558-16M-squashfs-sysupgrade.bin
erase 0x9f030000 +$filesize
cp.b $fileaddr 0x9f030000 $filesize
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 44620
This patch adds user-space support for the TL-MR12U board based on the mr13u patches.
Signed-off-by: Daniel Petre <daniel.petre@gmail.com>
SVN-Revision: 44426
This patch adds support for MERCURY MAC1200R, a dual band 802.11bgn + 802.11ac
router based on the AR9344, with QCA988x ath10k radio and 5 Fast Ethernet ports
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
SVN-Revision: 44359
This device is very similar to the TL-WR841N v8, only two LED GPIOs are
different.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 44255
The board is already supported by OpenWrt. WNR1000v2/WNR1000v2-VC are
pretty much the same as WNR2000v3/WNR612v2, therefore the same
initialization code and flash layout is used.
Signed-off-by: Ștefan Rusu <saltwaterc@gmail.com>
Tested-by: Douglas Fraser <1dsfraser@gmail.com>
SVN-Revision: 44221
the GPIO controlling the rf filter is not configured properly by this patch.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 44077
This adds support for the TP-LINK CPE210/220/510/520 (Pharos series). These
devices are very similar to the Ubiquiti NanoStations, but with better specs:
faster CPU, more RAM, 2x2 MIMO.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 43385
Qihoo 360 C301 is a dual band wireless router supports 802.11n and 802.11ac.
Its chipset is AR9344 + AR9882 with two 16MB flashes.
This patch adds its initial support.
v2:
* use mtd_get_mac_ascii to fetch MAC address for ath10k.
* use ath79_register_pci to initialize AR9882.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
SVN-Revision: 42552
This patch adds support for the Ubiquiti Networks airGateway.
Based in part on code posted by David Hutchison <dhutchison@bluemesh.net> on openwrt-devel:
https://lists.openwrt.org/pipermail/openwrt-devel/2013-December/023035.html
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
SVN-Revision: 41766
This enables the procd nand upgrade for ZyXEL NBG 6716. Also the ubi config
is cleaned up to match the wndr4300.
Signed-off-by: André Valentin <avalentin@marcant.net>
SVN-Revision: 41346
Dlink dir-615-e1 can use dir-600-a1's image, but the image can't be
uploaded through dlink's normal firmware update web page.
Add profile for dir-615-e1 so the generated image can be uploaded
through the firmware update web page.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
SVN-Revision: 40969
ARGC is a 'C-ism', but not known/valid in shell-syntax - insert the correct
var $# (=number of args) here. under normal conditions this had no impact,
but we should at least correct it. the error was observable like this:
root@box:~ [ -e "/etc/functions.sh" ] && . /etc/functions.sh
root@box:~ [ -e "/lib/functions.sh" ] && . /lib/functions.sh
root@box:~ . /lib/upgrade/platform.sh
root@box:~ . /lib/upgrade/common.sh
root@box:~ platform_check_image /tmp/myfirmware.bin
ash: bad number
root@box:~ echo $?
0
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 40915
Everything seems to be working fine. Potential issues:
* VLAN port IDs are reversed with regard to the numbers on the case.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 40400
Patch-by: Lars Bøgild Thomsen <lth@cow.dk>
Patchwork: http://patchwork.openwrt.org/patch/4922/
[juhosg: use correct board name in uci-defaults/02_network]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40033
Patch-by: TenNinjas <tenninjas@tenninjas.ca>
Patchwork: http://patchwork.openwrt.org/patch/4849/
[juhosg:
- use the Archer C7 specific LED setup instead of adding
identical code]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39636
The original dragino2 board support was missing some changes from the
upstream svn repository (http://svn.dragino.com/dragino2) that supported
sysupgrade.
[juhosg: change subject]
Signed-off-by: Karl Palsson <karlp@remake.is>
Patchwork: http://patchwork.openwrt.org/patch/4801/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39429
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
[juhosg: remove the image generation part until the ethernet
switch issue is resolved]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39078
Patch to add the user space support for the TL-WA801ND v2
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Patchwork: http://patchwork.openwrt.org/patch/4501/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39064
That function provides a slightly improved sanity check than the
currently used solution.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38967
This patch enables the convenient sysupgrade feature for
WD's Wi-Fi Range Extender.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Patchwork: http://patchwork.openwrt.org/patch/4341/
[juhosg:
- rename 'mynet_rext_check_image' function to 'cybertan_check_image'
and move that into platform.sh,
- remove the the model specific 'platform_do_upgrade_mynet_rext' function,
- drop the mynet-rext.sh script,
- remove the image/Makefile change,
- update commit message]
[christian:
- check all 8 bytes of the firmware/device magic]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38966
Patch to add the user space support for the TL-WR842N/ND v2
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4354/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38814
The current implementation of mtd will not append the backup
file created by sysupgrade to the correct partition, as mtd will append
the data to first jffs2 partition it finds. As the kernel is also
stored on a jffs2 partition (which resides before the overlay
partition), the data will be appended to this partition.
To fix this problem, a new option
-s <number> skip the first n bytes when appending data to the jffs2 partiton, defaults to "0"
is added to mtd.
Signed-off-by: Peter Wagner <tripolar@gmx.at>
SVN-Revision: 38807
Patch to add user space support for the TL-WA750RE/WA850RE range extender
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38718
Both Allnet and OpenMesh sysupgrade uses fw_setenv from uboot-envtools to
change different settings in the uboot environment. uboot-envtools version
2013.01 introduced a filesystem lock "/var/lock/fw_printenv.lock" to guarantee
mutually exclusive access to the uboot environment. But the path /var doesn't
exist on the sysupgrade ramfs.
An upgrade on these devices fails since r36033 ("[package] uboot-envtools:
upgrade to version 2013.01.01") with following messages:
Error opening lock file /var/lock/fw_printenv.lock
failed to update U-Boot environment
Creating the "/var/lock" path before running fw_setenv is therefore a
requirement unless the locking functionality in fw_setenv is removed or
replaced with optional locking.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38483
