Commit Graph

25596 Commits

Author SHA1 Message Date
Daniel Golle
5e6867fd54
mediatek: u7623-02: enable early console also in legacy image
Append 'earlycon=uart8250,mmio32,0x11004000' to the boot arguments
embedded in device-tree in order to enable early console on the
UniElec U7623 board when using the vendor/stock bootloader.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-01-31 00:10:38 +00:00
Rafał Miłecki
840f07e532 bcm4908: backport bcm_sf2 patch for better LED registers support
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-01-31 00:58:02 +01:00
Rafał Miłecki
a11e9fd1d5 bcm4908: fixup pinctrl patches for kernel 5.4
Fixes: b014589167 ("bcm4908: backport BCM4908 pinctrl driver")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-01-31 00:57:58 +01:00
Rafał Miłecki
b014589167 bcm4908: backport BCM4908 pinctrl driver
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-01-31 00:19:34 +01:00
Tamas Balogh
b21bc3479d ath79: ASUS RP-AC66 use flash till the end
This makes available the additional space,
which was occupied by OEM's jffs2 partition before:
"0x000000f80000-0x000001000000 : jffs2"

Reverting to the OEM firmware will also recover
this partition, i.e. it is not needed and can be
used by OpenWrt.

Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
2022-01-30 01:16:14 +09:00
Davide Fioravanti
8fde82095b ramips: add support for Wavlink WL-WN535K1
The Wavlink WL-WN535K1 is a "mesh" router with 2 gigabit ethernet ports
and one fast ethernet port. Mine is branded as Talius TAL-WMESH1.
It can be found in kits of 2 or 3 (WL-WN535K2 or WL-WN535K3).
The motherboard is labelled as WS-WN535G3-B-V1.2 so this image could
potentially work for WL-WN535G3R and WS-WN535G3R with little to none
effort, but it's untested.

Hardware
--------
SoC:   Mediatek MT7620A
RAM:   64MB
FLASH: 8MB NOR (GigaDevice GD25Q64CS)
ETH:
  - 2x 10/100/1000 Mbps Ethernet (RTL8211F)
  - 1x 10/100 Mbps Ethernet (integrated in SOC)
WIFI:
  - 2.4GHz: 1x (integrated in SOC) (2x2:2)
  - 5GHz:   1x MT7612E (2x2:2)
  - 4 internal antennas
BTN:
  - 1x Reset button
  - 1x Touchlink button (set to WPS)
  - 1x ON/OFF switch
LEDS:
  - 1x Red led (system status)
  - 1x Blue led (system status)
  - 3x Green leds (ethernet port status/act)
UART:
  - 57600-8-N-1

Everything works correctly.

Currently there is no firmware update available. Because of this, in
order to restore the OEM firmware, you must firstly dump the OEM
firmware from your router before you flash the OpenWrt image.

Backup the OEM Firmware
-----------------------
The following steps are to be intended for users having little to none
experience in linux. Obviously there are many ways to backup the OEM
firmware, but probably this is the easiest way for this router.
Procedure tested on WN535K1_V1510_200916 firmware version.

1) Go to http://192.168.10.1/webcmd.shtml

2) Type the following line in the "Command" input box and then press enter:
	mkdir /etc_ro/lighttpd/www/dev; dd if=/dev/mtd0ro of=/etc_ro/lighttpd/www/dev/mtd0ro

3) After few seconds in the textarea should appear this output:
		16384+0 records in
	16384+0 records out

   If your output doesn't match mine, stop reading and ask for
   help in the forum.

4) Open in another tab http://192.168.10.1/dev/mtd0ro to download the
   content of the whole NOR. If the file size is 0 byte, stop reading
   and ask for help in the forum.

5) Come back to the http://192.168.10.1/webcmd.shtml webpage and type:
	rm /etc_ro/lighttpd/www/dev/mtd0ro;for i in 1 2 3 4 5; do dd if=/dev/mtd${i}ro of=/etc_ro/lighttpd/www/dev/mtd${i}ro; done

6) After few seconds, in the textarea should appear this output:
		384+0 records in
	384+0 records out
	128+0 records in
	128+0 records out
	128+0 records in
	128+0 records out
	14720+0 records in
	14720+0 records out
	1024+0 records in
	1024+0 records out

   If your output doesn't match mine, stop reading and ask for
   help in the forum.

7) Open the following links to download the partitions of the OEM FW:
	http://192.168.10.1/dev/mtd1ro
	http://192.168.10.1/dev/mtd2ro
	http://192.168.10.1/dev/mtd3ro
	http://192.168.10.1/dev/mtd4ro
	http://192.168.10.1/dev/mtd5ro

   If one (or more) of these files are 0 byte, stop reading and ask
   for help in the forum.

8) Store these downloaded files in a safe place.

9) Reboot your router to remove any temporary file in ram.

Installation
------------
Flash the initramfs image in the OEM firmware interface
(http://192.168.10.1/update_mesh.shtml).
When Openwrt boots, flash the sysupgrade image otherwise you won't be
able to keep configuration between reboots.

Restore OEM Firmware
--------------------
Flash the "mtd4ro" file you previously backed-up directly from LUCI.
Warning: Remember to not keep settings!
Warning2: Remember to force the flash.

Notes
-----
1) Router mac addresses:
   LAN		XX:XX:XX:XX:XX:E2 (factory @ 0x28)
   WAN		XX:XX:XX:XX:XX:E3 (factory @ 0x2e)
   WIFI 2G	XX:XX:XX:XX:XX:E4 (factory @ 0x04)
   WIFI 5G	XX:XX:XX:XX:XX:E5 (factory @ 0x8004)

   LABEL	XX:XX:XX:XX:XX:E5

2) The OEM firmware upgrade page accepts only files containing the
   string "WN535K1" in the filename.

3) Additional notes 1,2,3 in the WS-WN583A6 commit are still valid
(92780d80ab)

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
[remove trailing whitespace]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-30 01:15:23 +09:00
Sungbo Eo
f4a79148f8 ramips: add support for ipTIME AX2004M
ipTIME AX2004M is an 802.11ax (Wi-Fi 6) router, based on MediaTek
MT7621A.

Specification:
* SoC: MT7621A
* RAM: 256 MiB
* Flash: NAND 128 MiB
* Wi-Fi:
  * MT7915D: 2.4/5 GHz (DBDC)
* Ethernet: 5x 1GbE
  * Switch: SoC built-in
* USB: 1x 3.0
* UART: J4 (115200 baud)
  * Pinout: [3V3] (TXD) (RXD) (GND)

MAC address:

| interface |        MAC        |     source     | comment
|-----------|-------------------|----------------|---------
|       LAN | 58:XX:XX:00:XX:9B |                | [1]
|       WAN | 58:XX:XX:00:XX:99 |                |
|   WLAN 2G | 58:XX:XX:00:XX:98 | factory 0x4    |
|   WLAN 5G | 5A:XX:XX:40:XX:98 |                |
|           |                   |                |
|           | 58:XX:XX:00:XX:98 | config ethaddr |

[1] Used in this patch as WLAN 5G MAC address with the local bit set

Load address:
* stock
  * 0x80010000: FIT image
  * 0x81001000: kernel image -> entry
* OpenWrt
  * 0x80010000: FIT image
  * 0x82000000: uncompressed kernel+relocate image
  * 0x80001000: relocated kernel image -> entry

Installation via **recovery** mode:
1.  Press reset button, power up the device, wait >10s for CPU LED
    to stop blinking.
2.  Upload recovery image through the recovery web page at 192.168.0.1.

Revert to stock firmware:
1.  Install stock image via recovery mode.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-29 23:50:28 +09:00
Sungbo Eo
03aa57d7ab ramips: make the relocation address configurable
If no argument is given to relocate-kernel, KERNEL_LOADADDR will be used
just as before.

This is a preparation for ramips support of ipTIME AX2004M.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-29 23:50:28 +09:00
Sungbo Eo
6ff970bb51 mvebu: add support for ipTIME NAS1dual
ipTIME NAS1dual is a 1-bay NAS, based on Marvell Armada 385 SoC.

Specifications:
* SoC: 88F6820
* RAM: 2 GiB
* Flash: SPI NOR 64 MiB
* SATA: 1x 3Gb/s
* Ethernet: 2x 1GbE
* USB: 1x 3.0
* Fan: 2 speed level
* UART: J11 (115200 8N1)
  * Pinout: [3V3] (TXD) (RXD) (GND)

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-29 23:50:28 +09:00
Sungbo Eo
f4fd2a1354 mvebu: remove duplicate CONFIG_POWER_RESET entries
The option is already enabled in the target config since 9149ed4f05
("mvebu: cortexa9: Add support for Ctera C200-V2").

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-29 23:50:28 +09:00
Sungbo Eo
7a4a33060f kernel: add disabled POWER_RESET_QNAP
Move the disabled symbol from target configs to generic configs.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-29 23:50:28 +09:00
Sungbo Eo
957f9adeb1 kirkwood: add support for ipTIME NAS1
ipTIME NAS1 is a 1-bay NAS, based on Marvell Kirkwood SoC.

Specifications:
* SoC: 88F6281
* RAM: 256 MiB
* Flash: SPI NOR 16 MiB
* SATA: 1x 3Gb/s
* Ethernet: 1x 1GbE
* USB: 1x 2.0
* Fan: 2 speed level
* UART: JP1 (115200 8N1)
  * Pinout: [3V3] (TXD) (RXD) (GND)

Notes:
* There are several variants of the model name: "NAS-I", "NASI", "NAS1".
  Here "NAS1" is adopted for consistent naming scheme.
* The reset button is also a USB copy button in stock FW,
  but in this patch the former is the only default behavior.

Installation via web interface:
1.  Flash sysupgrade image through the stock web interface.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-29 23:50:28 +09:00
Sungbo Eo
0c568d044f kirkwood: rework 02_network
Just like other targets do, introduce two setup functions for interfaces
and MAC addresses.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-29 23:50:28 +09:00
Sungbo Eo
aaebc7aa2e kirkwood: drop kernel 5.4 support
It has been 3 months since we switched this target to 5.10, now we can
remove the 5.4 files.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-29 23:50:28 +09:00
Sungbo Eo
81a561b4a6 kernel: move bootargs-append patch to generic
This moves bootargs-append support patch from ipq40xx and ipq806x to
generic. This way we can append additional boot arguments from DTS instead
of only being able to overwrite them.

This is a preparation for kirkwood support of ipTIME NAS1.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-29 23:50:28 +09:00
John Audia
30cff7c3b0 kernel: bump 5.4 to 5.4.174
Removed upstreamed patches:
  layerscape/patches-5.4/302-dts-0083-arm64-ls1028a-qds-correct-bus-of-rtc.patch[1]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.4.174&id=65816c1034769e714edb70f59a33bc5472d9e55f

Build system: x86_64
Build-tested: ramips/mt7621

Signed-off-by: John Audia <graysky@archlinux.us>
2022-01-28 22:06:03 +01:00
Hauke Mehrtens
d2ae4821c2 octeontx: Refresh kernel configuration
Refresh the kernel configuration.
No manual changes done.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-01-28 21:58:26 +01:00
Hauke Mehrtens
c120f7943e kernel: Add CONFIG_CRYPTO_DEV_OCTEONTX_CPT kernel config option
This new kernel configuration option is available when building the
octeontx target.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-01-28 21:58:26 +01:00
Hauke Mehrtens
764b1ecb69 kernel: Fix compile warning
This fixes the following compile warning:
  CC      init/do_mounts.o
init/do_mounts.c:478:19: warning: 'mount_ubi_rootfs' defined but not used [-Wunused-function]
  478 | static int __init mount_ubi_rootfs(void)
      |                   ^~~~~~~~~~~~~~~~

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-01-28 21:58:26 +01:00
Hauke Mehrtens
fcb29171bc arc770: Remove arc770 target
The arc700 target is not booting up since some time, see here:
https://github.com/foss-for-synopsys-dwc-arc-processors/toolchain/issues/400

It looks like there is a problem in the toolchain when using glibc.

Currently no one is working on fixing this problem, remove the target
instead. This target also does not have many users we are aware of.

If someone wants to have this target back, feel free to add a fixed
version of this target again.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-01-28 21:58:24 +01:00
Stijn Tintel
a47f152943 ramips: enable I2C_CHARDEV in mt7621/config-5.10
I2C_CHARDEV used to be enabled in mt7621/config-5.4. Enable it in the
5.10 config, as it's required for PoE control on Unifi Switch Flex.

Fixes: b4aad29a1d ("ramips: add support for kernel 5.10")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-01-28 19:03:52 +02:00
Chuanhong Guo
c06482489d kernel: 5.10: drop broken-flash-reset patch
Flash accessing instruction templates are determined during probe since
v5.6 for spimem-dirmap support in spi-nor driver in upstream commit:
df5c21002cf4 ("mtd: spi-nor: use spi-mem dirmap API")
As a result, changing bus_width on the fly doesn't work anymore and this
patch will cause executing spi-mem ops with 3-byte address on 16-32M
flash area.
We can't easily revert that behavioral change upstream so drop the patch
to prevent u-boot and eeprom from being erased.

Fixes: b10d604459("kernel: add linux 5.10 support")
Reported-by: Frank Di Matteo <dimatto@foxmail.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2022-01-28 21:03:10 +08:00
David Bauer
2b583ab8a7 rockchip: disable UHS modes for NanoPi R4S
The NanoPi R4S leaves the SD card in 1.8V signalling when rebooting
while U-Boot requires the card to be in 3.3V mode.

Remove UHS support from the SD controller so the card remains in 3.3V
mode. This reduces transfer speeds but ensures a reboot whether from
userspace or following a kernel panic is always working.

Signed-off-by: David Bauer <mail@david-bauer.net>
2022-01-27 01:44:28 +01:00
Daniel Golle
f5865452ac
mediatek: mt7623: include regular AHCI PCI driver
The legacy image for the UniElec U7623-02 until now included
kmod-ata-ahci-mtk. The MT7623 chip doesn't have that IP and that
board uses a PCIe-connected AHCI controller for the SATA port and
mSATA-pins of the mPCIe socket. Hence include kmod-ata-ahci instead.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-01-25 00:38:28 +00:00
Robert Marko
b8ef54f5da ipq40xx: drop 5.4 kernel
Since 5.10 is now default, no point in keeping
5.4 around.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2022-01-24 12:07:42 +01:00
Daniel Golle
f5278bf820
mediatek: store random MAC address in U-Boot env on first boot
For devboards without a MAC address assigned from factory, store
the random MAC in U-Boot env on first boot to make it persistent.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-01-23 20:20:47 +00:00
Daniel Golle
31872a38be
uboot-envtools: add configuration for UniElec U7623 board
Add U-Boot env settings to allow accessing the environment using
fw_printenv and fw_setenv tools on the UniElec U7623 board.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-01-23 20:20:42 +00:00
Daniel Golle
1ee75dd290
mediatek: mt7623: rework images for U7623-02 board
Users of older OpenWrt versions need sysupgrade using the *emmc.img.gz
file once which will upgrade U-Boot and switch to the new image layout.
Users of the vendor firmware need to first flash the legacy image to
then sunsequently carry out a full-flash upgrade.

Alternatively the board can also be flashed using MediaTek's
proprietary SP Flash Tool.

Configuration as well as persistent MAC address will be lost once at
this point and you will have to redo (or restore) all configuration
manually. To restore the previous persistent MAC address users may set
it manually using

fw_setenv ethaddr 00:11:22:33:44:55

For future upgrades once running OpenWrt past this commit, the usual
*sysupgrade.itb file can be used.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-01-23 20:20:37 +00:00
Daniel Golle
4356e2b58a
mediatek: add common DTS aliases for UniElec U7623 board
* Use serial0 instead of serial2 for the only serial port
 * Add LED aliases
 * Add ethernet0 alias to inherit ethaddr from U-Boot env

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-01-23 19:48:36 +00:00
Daniel Golle
8a324fb759
uml: make use of 'rootfs-part' feature
Use 'rootfs-part' feature instead of referencing the TARGET_uml in
Config-images.in.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-01-23 19:48:31 +00:00
Daniel Golle
d05ac928f6
sunxi: make use of 'rootfs-part' feature
Use 'rootfs-part' feature instead of referencing the TARGET_sunxi in
Config-images.in.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-01-23 19:48:25 +00:00
Daniel Golle
3a69b4bbb9
omap: make use of 'rootfs-part' feature
Use 'rootfs-part' feature instead of referencing the TARGET_omap in
Config-images.in.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-01-23 19:48:20 +00:00
Daniel Golle
a40b4d335a
mediatek: use CONFIG_TARGET_ROOTFS_PARTSIZE
Enable 'rootfs-part' feature to make the size of the partition of the
production image configurable instead of hard-coding it.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-01-23 19:48:07 +00:00
Victorien Molle
af8a059bb4 ath79: add support for GL.iNet GL-XE300
The GL.iNet GL-XE300 is a 4G LTE Wireless router, based on QCA9531 SoC.

Specifications:

 - SoC: QCA9531 (650MHz)
 - RAM: DDR2 128M
 - Flash: SPI NOR 16M + SPI NAND 128M
 - WiFi: 2.4GHz with 2 antennas
 - Ethernet:
   - 1x LAN (10/100M)
   - 1x WAN (10/100M)
 - LTE:
 - USB: 1x USB 2.0 port
 - UART:
   - 3.3V, TX, RX, GND / 115200 8N1

MAC addresses as verified by OEM firmware:

 use    address   source
 LAN    *:c5      art 0x0 (label)
 WAN    *:c6      label + 1
 WLAN   *:c7      art 0x1002

Installation via U-Boot rescue:

1. Press and hold reset and power buttons simultaneously
2. Wait for the LAN led to blink 5 times
3. Release reset and power buttons
4. The rescue page is accessible via http://192.168.1.1
5. Select the OpenWrt factory image and start upgrade
6. Wait for the router to flash new firmware and reboot

Revert to stock firmware:

 i. Download the stock firmware from GL.Inet website
 ii. Use the same method explained above to flash the stock firmware

Signed-off-by: Victorien Molle <victorien.molle@wifirst.fr>
[update commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
2022-01-22 01:17:16 +01:00
Rodrigo Araujo
7c8ade1765 ramips: correct vendor name for COMFAST/Joowin
When Joowin WR758AC V1 and V2 devices were added, they should have been
added with the primary manufacturer name which is COMFAST, since Joowin
is just an alternate vendor name on some coutries or stores.

Fix this by changing the the vendor name on the respective files and set
Joowin as ALT0 variants while ensuring compatibility for early users.
Also adjust the model names to better follow the naming rules.

As a side effect, fix mt76x8 network script which was left incorrectly
unsorted on the case block conditions.

Fixes: 766733e172 ("ramips: add support for Joowin WR758AC V1 and V2")
Signed-off-by: Rodrigo Araujo <araujo.rm@gmail.com>
2022-01-22 01:17:04 +01:00
David Bauer
ef5f3eb700 ramips: read Tenbay T-MB5EU address from single location
Currently the WAN MAC address is read from a different offset contrary
to all other addresses.

There's conflicting information whether offset 0x28 on the factory
partition contains the valid WAN mac for all devices while 0x4 seems to
be uniform.

Read the WAN mac from this location and calculate it.

Signed-off-by: David Bauer <mail@david-bauer.net>
2022-01-22 01:16:56 +01:00
David Bauer
b0c04a37e4 ramips: update Tenbay T-MB5EU wireless MAC address
The current MAC address assignment is still incorrect.

Use the same MAC address as seen on the stock firmware
for both wireless interfaces.

The 5GHz MAC address OUI is +2 in the first EUI octet. We currently
don't do this in OpenWrt. Ignore this offset for now. With the current
assignment, recurring MAC addresses between radios is already taken care
of.

Signed-off-by: David Bauer <mail@david-bauer.net>
2022-01-22 01:16:49 +01:00
David Woodhouse
408b6558e4 ipq806x: Netgear D7800: Fix RAM and enable PCIe #2
This board has 512MiB of RAM like the R7800, and the VDSL modem is
attached to the second PCIe port.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2022-01-21 17:18:35 +00:00
Denis Kalashnikov
ec85e48a11 ath79: add support for reset key on MikroTik RB912UAG-2HPnD
On MikroTik RB91x board series a reset key shares SoC gpio
line #15 with NAND ALE and NAND IO7. So we need a custom
gpio driver to manage this non-trivial connection schema.
Also rb91x-nand needs to have an ability to disable a polling
of the key while it works with NAND.

While we've been integrating rb91x-key into a firmware, we've
figured out that:
* In the gpio-latch driver we need to add a "cansleep" suffix to
several gpiolib calls,
* When gpio-latch and rb91x-nand fail to get a gpio and an error
is -EPROBE_DEFER, they shouldn't report about this, since this
actually is not an error and occurs when the gpio-latch probe
function is called before the rb91x-key probe.
We fix these related things here too.

Signed-off-by: Denis Kalashnikov <denis281089@gmail.com>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2022-01-19 16:40:12 +01:00
Paul Spooren
522e414dcb layerscape: switch to 5.10 Kernel
Tested by multiple users and since all targets need to be on Kernel 5.10
to be part of the next release, add changes.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2022-01-19 09:44:26 +01:00
Klaus Kudielka
431f379e9d mvebu: cortexa9: Fix board.d/01_leds
Fix syntax error in the case statement

Fixes: 9149ed4f05 ("mvebu: cortexa9: Add support for Ctera C200-V2")
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
2022-01-18 20:13:14 +01:00
Sungbo Eo
266b5c83c3 ipq40xx: rename RT-AC42U WLAN/LAN LEDs
Assign LED numbers properly by adding function-enumerator property in DTS.

While at it, remove default trigger of LAN LEDs as it will be handled in
01_leds anyway.

Fixes: 51b9aef553 ("ipq40xx: add support for ASUS RT-ACRH17/RT-AC42U")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-17 20:38:43 +09:00
Sungbo Eo
e257405c1b ipq40xx: image: remove unused DTB_SIZE variable
It is not included in DEVICE_VARS anyways.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-17 20:38:43 +09:00
Alexey Smirnov
e23ca355b0 omap: add support for the TRNG Hardware Accelerator
According to TI docs (Processor SDK Linux Getting Started Guide)
the Random Number Generator hardware is found on
OMAP16xx, OMAP2/3/4/5, AM33xx/AM43xx boards. It already
defined in device tree files. Let's enable it.

Some tests:

root@RTS1_OI:~# rngtest -c 1000 </dev/hwrng
rngtest 6.10
Copyright (c) 2004 by Henrique de Moraes Holschuh
This is free software; see the source for copying conditions.
There is NO warranty; not even for MERCHANTABILITY or
FITNESS FOR A PARTICULAR PURPOSE.

rngtest: starting FIPS tests...
rngtest: bits received from input: 20000032
rngtest: FIPS 140-2 successes: 999
rngtest: FIPS 140-2 failures: 1
rngtest: FIPS 140-2(2001-10-10) Monobit: 0
rngtest: FIPS 140-2(2001-10-10) Poker: 0
rngtest: FIPS 140-2(2001-10-10) Runs: 1
rngtest: FIPS 140-2(2001-10-10) Long run: 0
rngtest: FIPS 140-2(2001-10-10) Continuous run: 0
rngtest: input channel speed: (min=198.710; avg=1265.501; max=2976.417)Kibits/s
rngtest: FIPS tests speed: (min=1.780; avg=37.085; max=39.736)Mibits/s
rngtest: Program run time: 15961329 microseconds

Signed-off-by: Alexey Smirnov <s.alexey@gmail.com>
2022-01-16 21:42:19 +01:00
Daniel Kestrel
78057b5595 ltq-deu: add ltq-deu back to default packages
After enhancing ltq-deu, build it by default for the devices
using it.

Reverts: 964863b ("ltq-deu: Mark lantiq DEU broken")

Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
2022-01-16 21:42:19 +01:00
Lech Perczak
ebf639d282 ath79: use lzma-loader for ZyXEL NBG6716
Since gzip-compressed kernel image stopped fitting on 4MB kernel
partition on the device, use lzma-loader wrapping LZMA-compressed
kernel. This yields bootable device once again, and saves a very
substantial amount of space, the kernel size decreasing from about 4.4MB
to about 2.5MB for 5.10 kernel. This avoids changing of the flash layout
for the device.

While at that, reactivate the build for the device.

Fixes: 5d8ea6d34f ("ath79: Deactivate ZyXEL NBG6716 by default")
Cc: André Valentin <avalentin@marcant.net>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Alex Henrie <alexhenrie24@gmail.com>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2022-01-16 21:42:19 +01:00
Sven Eckelmann
8143709c90 ath79: Add support for OpenMesh OM2P v1
Device specifications:
======================

* Qualcomm/Atheros AR7240 rev 2
* 350/350/175 MHz (CPU/DDR/AHB)
* 32 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 1T1R 2.4 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
  - eth0
    + 18-24V passive POE (mode B)
    + used as WAN interface
  - eth1
    + builtin switch port 4
    + used as LAN interface
* 12-24V 1A DC
* external antenna

The device itself requires the mtdparts from the uboot arguments to
properly boot the flashed image and to support dual-boot (primary +
recovery image). Unfortunately, the name of the mtd device in mtdparts is
still using the legacy name "ar7240-nor0" which must be supplied using the
Linux-specfic DT parameter linux,mtd-name to overwrite the generic name
"spi0.0".

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

   setenv serverip 192.168.1.21
   setenv ipaddr 192.168.1.1
   tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to the
device via

  scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

  sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2022-01-16 21:42:19 +01:00
Sven Eckelmann
7f074fe1a7 ath79: Allow to set spi-nor mtd name via devicetree
On ar71xx, it was possible to overwrite the name of the spi-nor mtd device
identifier using the flash_platform_data which each mach-*.c could adjust
for its devices. A similar feature was introduced for mtd-physmap in
devicetree's. The property linux,mtd-name can be used to set the name and
provide a stable identifier for mtdpart from the bootloader.

But this feature is not yet available upstream for spi-nor devices which
also might receive their partition layout from the bootloader. But the
OpenWrt pistachio support for this property can simply be imported into
ath79 to gain this support.

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2022-01-16 21:42:19 +01:00
Sven Eckelmann
1699c1dc7f ath79: Add support for OpenMesh OM5P-AC v2
Device specifications:
======================

* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/200 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi (11n)
* 2T2R 5 GHz Wi-Fi (11ac)
* 4x GPIO-LEDs (3x wifi, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring
* 2x ethernet
  - eth0
    + AR8035 ethernet PHY (RGMII)
    + 10/100/1000 Mbps Ethernet
    + 802.3af POE
    + used as LAN interface
  - eth1
    + AR8031 ethernet PHY (RGMII)
    + 10/100/1000 Mbps Ethernet
    + 18-24V passive POE (mode B)
    + used as WAN interface
* 12-24V 1A DC
* internal antennas

This device support is based on the partially working stub from commit
53c474abbd ("ath79: add new OF only target for QCA MIPS silicon").

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

   setenv serverip 192.168.1.21
   setenv ipaddr 192.168.1.1
   tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to the
device via

  scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

  sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2022-01-16 20:51:14 +01:00
Aleksander Jan Bajkowski
7e484b902d lantiq: backport latest upstream patches
This patch includes a series of performance improvements. All patches
were accepted and should land in 5.17.
NAT Performance results on BT Home Hub 5A (kernel 5.10.89, mtu 1500):

	Down		Up
Before	539 Mbps	599 Mbps
After	624 Mbps	695 Mbps

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-01-16 20:51:14 +01:00
Thomas Nixon
255268ce1a lantiq: xrx200: enable use of baby jumbo frames
xrx200 max MTU is reduced so that it works correctly when set to the
max, and the max MTU of the switch is increased to match.

In 5.10, the switch driver now enables non-standard MTUs on a per-port
basis, with the overall frame size set based on the cpu port. When the
MTU is not used, this should have no effect. The maximum packet size is
limited as large packets cause the switch to lock up.

0702-net-lantiq-add-support-for-jumbo-frames.patch comes from net-next
commit 998ac358019e491217e752bc6dcbb3afb2a6fa3e.

In 5.4, all switch ports are configured to accept the max MTU, as 5.4
does not have port_max_mtu/port_change_mtu callbacks.

Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
2022-01-16 20:51:14 +01:00
Rui Salvaterra
61e58f7cec kernel: bump 5.10 to 5.10.92
Patches automatically rebased.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2022-01-16 20:51:14 +01:00
Rui Salvaterra
7229981994 kernel: bump 5.10 to 5.10.91
Patches automatically rebased.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2022-01-16 20:51:14 +01:00
John Audia
a28afb9214 kernel: bump 5.4 to 5.4.172
All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/mt7621

Signed-off-by: John Audia <graysky@archlinux.us>
2022-01-16 16:23:45 +01:00
John Audia
53252c4ce9 kernel: bump 5.4 to 5.4.171
All patches automatically rebased.

Signed-off-by: John Audia <graysky@archlinux.us>
2022-01-16 16:23:44 +01:00
Christian Lamparter
0a852d8a5e ipq40xx: AP-365: fix non-existent node or label "macaddr_mfginfo_1d"
Chen Minqiang reported on github:
|  DTC     arch/arm/boot/dts/qcom-ipq4029-ap-365.dtb
|qcom-ipq4019.dtsi:520.23-560.5: ERROR (phandle_references): /soc/wifi@a000000:
|Reference to non-existent node or label "macaddr_mfginfo_1d"
|
|  also defined at qcom-ipq4029-aruba-glenmorangie.dtsi:243.8-248.3
|qcom-ipq4019.dtsi:562.23-602.5: ERROR (phandle_references): /soc/wifi@a800000:
|Reference to non-existent node or label "macaddr_mfginfo_1d"
|
|  also defined at qcom-ipq4029-aruba-glenmorangie.dtsi:250.8-256.3
|ERROR: Input tree has errors, aborting (use -f to force output)
|scripts/Makefile.lib:326: recipe for target 'qcom-ipq4029-ap-365.dtb' failed

Fixes: cfc13c4459 ("ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data")
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-01-16 13:14:58 +01:00
David Bauer
e821849c4f lantiq: increase fritz-cal-extract output limit
It was reported the caldata on the FritzBox 7430 is not only stored at
different offsets, but is also larger than the current output size
limit.

Increase the output file size limit (after deflate) by 1024 bytes.

Ref: FS#3604 ("ath9k firmware is 0 bytes on Fritzbox 7430")
Signed-off-by: David Bauer <mail@david-bauer.net>
2022-01-15 23:05:55 +01:00
Christian Lamparter
144609bb3d build: move Build/copy-file to image-commands.mk
This is makro is present in more than one place.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-01-15 19:29:42 +01:00
Tamas Balogh
872b65ecc8 ath79: patch Asus RP-AC66 clean up and fix for sysupgrade image
- clean up leftovers regarding MAC configure in dts
- fix alphabetical order in caldata
- IMAGE_SIZE for sysupgrade image

Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
2022-01-15 17:41:19 +01:00
Marek Behún
83ce42b54e mvebu: Move cortexa9 specific config options from global config
Move config options
  CONFIG_PHY_MVEBU_A38X_COMPHY
  CONFIG_RTC_DRV_MV
to cortexa9/config-5.10.

These are not needed for arm64 targets.

Signed-off-by: Marek Behún <kabel@kernel.org>
2022-01-15 17:41:19 +01:00
Pawel Dembicki
9149ed4f05 mvebu: cortexa9: Add support for Ctera C200-V2
2-Bay NAS - maximum two 3.5" Harddisks

Hardware:
  - SoC: Marvell 88F6707-A1 ARMv7 Processor 1,2GHz (ARMADA 370 SoC)
  - Ram: 1GB (2x Nanya NT5CC512M8DN-D1)
  - NAND Flash: 256MB (ESMT F59L2G81A-25T)
  - Lan: 1x GBE (Marvell 88E1318-NNB2)
  - Storage: 2x SATA HDD 3.5" Slot
  - USB: 2x USB 3.0 port (Renesas uPD720202)
  - Console: Internal J3 connector (1: Vcc, 2: Rx, 3: Tx, 4: GND)
  - LEDs: 13x GPIO controlled
  - Buttons: 2x GPIO controlled

Known issues:
  - Buzzer is unused due lack of proper driver
  - USB1/2 usbport ledtrigger won't work (through DT)
  - Renesas uPD720202 requires firmware file. It's possible to find
    non-free binary. Please look for 'UPDATE.mem' file and put in into
    '/lib/firmware/renesas_usb_fw.mem' file.

Installation:
  - Apply factory initramfs image via stock web-gui.
  - Do sysupgrade to make installation complete.

Back to stock:
  - OpenWrt rootfs partition use unused space after stock firmware.
  - Full revert is possible.
  - Login via ssh and run:

 ## ctera_c200-v2_back_to_factory start ##
 . /lib/functions.sh
 part=$(find_mtd_part "active_bank")
 active_bank=$(strings "$part" | grep bank)
 if [ "$active_bank" = "bank1" ]; then
 	echo "bank2" > /tmp/change_bank
 else
 	echo "bank1" > /tmp/change_bank
 fi
 mtd write /tmp/change_bank active_bank
 reboot
 ## ctera_c200-v2_back_to_factory end ##

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
(put back-to-stock script into commit message, removed dup. SUBPAGESIZE var,
added 01_leds for non-working dt-usb-port trigger)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-01-15 17:41:19 +01:00
Josef Schlehofer
01520a96e7 mvebu: enable watchdog for Armada 37XX
This option includes support for watchdog timer on Marvell Armada 37xx
SoCs. [1] It is useful e.g. for Turris MOX, Marvell ESPRESSObin

Enable armada-37xx-watchdog driver as built in for mvebu cortex-a53,
so that kernel can start serving as soon as the driver is probed, until userspace takes over it.

[1] https://cateee.net/lkddb/web-lkddb/ARMADA_37XX_WATCHDOG.html

Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
(improved commit message, 2nd paragraph)
Signed-off-by: Marek Behún <kabel@kernel.org>
2022-01-15 17:41:19 +01:00
Marek Behún
43659a7d74 mvebu: cortexa53: Enable Armada 37xx rWTM driver
Enabling Armada 37xx rWTM driver. This gives the kernel access to random
number generator, if provided by the rWTM firmware.

Note that the driver is called turris-mox-rwtm because it was initially
written for Turris MOX, but will also work on other Armada 37xx
platforms, if they use rWTM firmware from CZ.NIC [1].

It makes sense to have this driver built-in, so that kernel has access
to random number generator without needing to load any drivers.

[1] https://gitlab.nic.cz/turris/mox-boot-builder

Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andre Heider <a.heider@gmail.com>
2022-01-15 17:41:18 +01:00
Marek Behún
bf991fa357 kernel: 5.10: Backport pending Armada 3720 comphy patches
Backport 5 pending patches [1] for Armada 3720 comphy driver and one
patch for device tree, applied to mvebu-dt64, but pending to appear in
Linus' tree [2].

These patches makes the driver work correctly even with older, buggy
versions of TF-A firmware.

[1] http://lists.infradead.org/pipermail/linux-phy/2022-January/002598.html
[2] http://lists.infradead.org/pipermail/linux-phy/2021-December/002279.html

Signed-off-by: Marek Behún <kabel@kernel.org>
2022-01-15 17:26:55 +01:00
Marek Behún
cf3a6e62a1 kernel: 5.10: Backport Armada 3720 comphy patches from 5.15
Backport 2 patches for Armada 3720 comphy from 5.15 kernel.

These are needed for clear application of pending patches that fix this
driver.

Signed-off-by: Marek Behún <kabel@kernel.org>
2022-01-15 17:26:55 +01:00
Marek Behún
080691d7b1 kernel: 5.10: Backport pending pci-aardvark changes fixing MSI support
Backport Aardvark PCIe controller driver changes that fix MSI support,
that were recently sent to the linux-pci mailing list [1].

These changes fix MSI and MSI-X support for this PCIe controller, which,
among other things, make it possible to use NVMe drives with this PCIe
controllers.

[1] https://lore.kernel.org/linux-pci/20220110015018.26359-1-kabel@kernel.org/

Signed-off-by: Marek Behún <kabel@kernel.org>
2022-01-15 17:26:55 +01:00
Marek Behún
612e1c6801 kernel: 5.10: Backport pci-aardvark driver changes from 5.17
Backport Aardvark PCIe controller driver changes that will appear in
5.17 kernel. They are currently accessible on LKML [1], in linux-next
repository [2], or in Bjorn Helgaas' repository [3].

These changes mainly enhance driver removal method.

[1] https://lore.kernel.org/linux-pci/20211130172913.9727-1-kabel@kernel.org/
[2] https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/log/drivers/pci?h=next-20220107
[3] https://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci.git/log/?h=next

Signed-off-by: Marek Behún <kabel@kernel.org>
2022-01-15 17:26:55 +01:00
Josef Schlehofer
9d530ac4bf mvebu: kernel: enable CONFIG_BLK_DEV_NVME
CONFIG_BLK_DEV_NVME [1]:
- This is a kernel driver for SSD connected to PCI or PCIe bus [1].
By default, it is enabled for targets "ipq807x", "rockchip/armv8"
and "x86/64".

With miniPCIe adapter, there is a possibility to connect NVMe disk
to Turris Omnia (cortex-a9), Turris MOX (cortex-a53).

It allows to boot system from NVMe disk, because of that it can not
be kmod package as you can not access the disk to be able to boot from
it.

CONFIG_NVME_CORE [2]:
- This is selected by CONFIG_BLK_DEV_NVME
It does not need to be explicitly enabled, but it is done for "ipq807",
"x64_64" and rockchip/armv8", which has also enabled the previous config
option as well.

Kernel increase: ~28k KiB on mamba kernel

Reference:
[1] https://cateee.net/lkddb/web-lkddb/BLK_DEV_NVME.html
[2] https://cateee.net/lkddb/web-lkddb/NVME_CORE.html

Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
2022-01-15 17:26:55 +01:00
Christian Lamparter
cfc13c4459 ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data
moves extraction entries out of 11-ath10k-caldata and into
the individual board's device-tree.

Some notes:
 - mmc could work as well (not tested)
 - devices that pass the partitions via mtdparts
   bootargs are kept as is
 - gl-b2200 has a weird pcie wifi device
   (vendor claims 9886 wave 2. But firmware-extraction
   was for a wave 1 device?!)

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-01-15 17:26:55 +01:00
Christian Lamparter
10bc55c496 ipq40xx: add RT-ACRH13 alternative name to RT-AC58U
RT-ACRH13 is another name this device was sold as (US?).

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-01-15 17:26:55 +01:00
Joshua Roys
51b9aef553 ipq40xx: add support for ASUS RT-ACRH17/RT-AC42U
SOC:	IPQ4019
CPU:	Quad-core ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
DRAM:	256 MB
NAND:	128 MiB Macronix MX30LF1G18AC
ETH:	Qualcomm Atheros QCA8075 Gigabit Switch (4x LAN, 1x WAN)
USB:	1x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1:	Qualcomm Atheros QCA4019 2.4GHz 802.11bgn 2x2:2
WLAN2:	Qualcomm Atheros QCA9984 5GHz 802.11nac 4x4:4
INPUT:	1x WPS, 1x Reset
LEDS:	Status, WIFI1, WIFI2, WAN (red & blue), 4x LAN

This board is very similar to the RT-ACRH13/RT-AC58U. It must be flashed
with an intermediary initramfs image, the jffs2 ubi volume deleted, and
then finally a sysupgrade with the final image performed.

Signed-off-by: Joshua Roys <roysjosh@gmail.com>
(added ALT0)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-01-15 17:21:01 +01:00
Michael Pratt
74516f4357 ramips: fix reboot for remaining 32 MB boards
The following devices have a Winbond W25Q256FV flash chip,
which does not have the RESET pin enabled by default,
and otherwise would require setting a bit in a status register.

Before moving to Linux 5.4, we had the patch:
0053-mtd-spi-nor-add-w25q256-3b-mode-switch.patch
which kept specific flash chips with explicit 3-byte and 4-byte address modes
to stay in 3-byte address mode while idle (after an erase or write)
by using a custom flag SPI_NOR_4B_READ_OP that was part of the patch.

this was obsoleted by the patch:
481-mtd-spi-nor-rework-broken-flash-reset-support.patch
which uses the newer upstream flag SNOR_F_BROKEN_RESET
for devices with a flash chip that cannot be hardware reset with RESET pin
and therefore must be left in 3-byte address mode when idle.

The new patch requires that the DTS of affected devices
have the property "broken-flash-reset", which was not yet added for most of them.

This commit adds the property for remaining affected devices in ramips target,
specifically because of the flash chip model.

However, it is possible that there are other devices
where the flash chip uses an explicit 4-byte address mode
and the RESET pin is not connected to the SOC on the board,
and those DTS would also need this property.

Ref: 22d982ea00 ("ramips: add support for switching between 3-byte and 4-byte addressing")
Ref: dfa521f129 ("generic: spi-nor: rework broken-flash-reset")
Signed-off-by: Michael Pratt <mcpratt@pm.me>
2022-01-15 17:12:12 +01:00
Paul Spooren
daae59b729 at91: drop /etc/config/firewall
The file can't be part of base files or the base-files and firewall
packages collide. Two packages must not provide the same config files
without having a defined CONFLICT since it would result in an
undeterministic config state depending on what package is installed
last.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2022-01-15 16:36:28 +01:00
SeongUk Moon
9c8ccdcdc8 ramips: add support for ipTIME A6004NS-M
ipTIME A6004NS-M is a 2.4/5GHz band AC1900 router, based on MediaTek MT7621A.

Specifications:
- SoC: MediaTek MT7621A (880MHz, Duel-Core)
- RAM: DDR3 256MB
- Flash: SPI NOR 16MB (Winbond W25Q128BV)
- WiFi: MediaTek MT7615E (2.4GHz, 5GHz)
- Ethernet: MediaTek MT7530 (WAN x1, LAN x4, SoC built-in Estimated)
- USB: USB 3.0 x1
- UART: [3.3V, TX, RX, GND] (57600 8N1)

Installation via web interface:
1. Flash initramfs image using OEM's Firmware Update page.
2. Connect to OpenWrt with an SSH connection to `192.168.1.1`.
3. Perform sysupgrade with sysupgrade image.

Revert to stock firmware:
1.  Flash stock firmware via OEM's Recovery mode

How to use OEM's Recovery mode:
1. Power on the device and connect the shell through UART.
2. Connect to the shell and press the `t` key on the keyboard.
3. Set fixed IP with  `192.168.0.2`  with subnet mask  `255.255.255.0`
4. Flash image via TFTP to  `192.168.0.1`

Additional Notes:
1. The higher the 5Ghz Frequency, the lower the stability. It is recommended to use less than 5.775Ghz.
2. If the 5Ghz frequency is too high, 5Ghz may not work.
3. A6ns-M use shared dtsi file of A6004NS-M. (reference: /mt7621_iptime_a6004ns-m.dtsi).

Signed-off-by: SeongUk Moon <antegral@antegral.net>
[convert CRLF to LF]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-15 20:43:14 +09:00
Kyoungkyu Park
6041c693dd ramips: add support for HUMAX E2
HUMAX E2 (also known as HUMAX QUANTUM E2) is a 2.4/5GHz band AC router,
based on MediaTek MT7620A.

Specifications:
- SoC: MT7620A
- RAM: DDR2 64MB
- Flash: SPI NOR 8MB (MXIC MX25L6405D)
- WiFi:
  - 2.4GHz: SoC internal
  - 5GHz: MT7610E
- Ethernet: 1x 10/100Mbps
  - Switch: SoC internal
- UART: J2 (57600 8N1)
  - pinout: [3V3] (RXD) (GND) (TXD)

Installation and Recovery via TFTP:
1. Connect ethernet cable between Router port and PC Ethernet port.
2. Set your computer to a static IP **192.168.1.1**
3. Turn the device off and wait a few seconds. Hold the WPS button on front
   of device and insert power.
4. Send a firmware image to **192.168.1.6** using TFTP.
   You can use any TFTP client. (tftp, curl, Tftpd64...)
5. Wait until Power LED stop flashing. **DO NOT TURN OFF DEVICE!**
   The device will be automatically rebooted.

Signed-off-by: Kyoungkyu Park <choryu.park@choryu.space>
2022-01-15 20:05:46 +09:00
David Bauer
7f7705923a lantiq: add additional caldata offsets
It was reported the AVM FritzBox 7430 has different offsets for the
caldata depending on the device.

Whether this is due to custom bad-block handling or up to the installed
bootloader-version is unknown.

Try both known caldata offsets like it is already done for the ipq40xx
NAND based models. Use the same approach for the FritzBox 7412. While it
is currently unknown, whether it is affected, applying the same logic
has no downsides.

Signed-off-by: David Bauer <mail@david-bauer.net>
2022-01-15 11:27:53 +01:00
David Bauer
3154537864 lantiq: flag FritzBox 7360 family buttons active-low
All buttons of the FritzBox 7360 family are active-low, not active-high.
Corrent the GPIO flag. This fixes release triggers upon push of a button.

Reported-by: Jan-Niklas Burfeind <git@aiyionpri.me>
Signed-off-by: David Bauer <mail@david-bauer.net>
2022-01-14 22:12:53 +01:00
David Woodhouse
557067d9b1 mediatek: mt7623: Enable PCIe bus 0 (and thus SATA) on U7623
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2022-01-14 19:43:45 +00:00
Felix Fietkau
83b14ec026 ramips: enable badblock table support on linksys ea7xxx devices
Use remapping only on the kernel partitions.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-01-13 18:33:06 +01:00
Felix Fietkau
e2aa04d1e5 kernel: mtk_bmt: add support for the bbt format used on mt7621
This does not have spare blocks for remapping, and it is also not suitable
for random write access. It only skips over bad blocks on linear writes of an
image to a partition. As such, it is really only suitable for the kernel
partition, or other partitions with mostly static data

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-01-13 18:33:06 +01:00
Felix Fietkau
ff6b4f2cfb kernel: mtk_bmt: add abstraction for supporting other formats
Preparation for supporting remapping on MT7621

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-01-13 18:33:06 +01:00
Felix Fietkau
3c78fabb0d ramips: mt7621_nand: fix writing upper half of fdm data
Since the loop iterates from 0-3, subtracting 4 from the shift
multiplier does not make any sense

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-01-13 18:33:06 +01:00
Felix Fietkau
76b27f6bb9 mediatek: rework and fix mt7622-rfb1-ubi support
Limit bmt remapping range to cover everything up to and including the kernel image,
use the rest of the flash area for ubi.
Fix partition table and sysupgrade support

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-01-13 18:33:06 +01:00
Felix Fietkau
7235c8d00c kernel: mtk_bmt: remap blocks after reaching bitflip threshold
This ensures that blocks are remapped before data becomes corrupt

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-01-13 18:33:06 +01:00
Felix Fietkau
0ddead0897 kernel: mtk_bmt: pass number of bitflips on read to the caller
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-01-13 18:33:06 +01:00
Felix Fietkau
b86452f841 kernel: mtk_bmt: add support for limiting range of remapping
This can be used to support ubi on top of mtk_bmt without reflashing the
boot loader. The boot loader + factory + kernel area is covered, while the
rest is passed through as-is

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-01-13 18:33:06 +01:00
Felix Fietkau
31b6cfb288 kernel: mtk_bmt: extend debug interface
Add support for showing remapped blocks and garbage collecting old
remapped blocks triggered by using the mark_good/mark_bad files

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-01-13 18:33:06 +01:00
Felix Fietkau
fde2421597 kernel: mtk_bmt: fix remapping after read/write failure
Copy from the previous block in order to preserve existing data

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-01-13 18:33:06 +01:00
Felix Fietkau
bcf91fe884 kernel: move mediatek BMT support patch to generic patches
Preparation for supporting BMT on MT7621. Move source files to the files/
subdirectory in order to simplify maintenance

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-01-13 18:33:06 +01:00
Denis Kalashnikov
2d19e6c6a4 generic: platform/mikrotik: use MTD notifier
If the SPI probe is sufficiently delayed, the routerboot driver may fail
to init as the routerboot partitions are not yet available.

Register an MTD user notifier instead of doing straight init so that the
init subroutines are only executed when the target MTD partitions are
present.

Because the init/exit routines can now be called outside of the kernel
normal init/exit calls, they cannot be jettisoned and must always be
available: the __init and __exit qualifiers are thus removed.

Reported-by: Denis Kalashnikov <denis281089@gmail.com>
Signed-off-by: Denis Kalashnikov <denis281089@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
[bump hardconfig/softconfig versions]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2022-01-13 09:33:29 +01:00
Koen Vandeputte
9571d9d4b1 ath79: qca955x: remove double declaration
No need to mention the same value twice

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2022-01-13 09:33:29 +01:00
Koen Vandeputte
f11df68956 ath79: rb912: remove unused property
ar934x does not define property 'rgmii-enabled' in the parsing code
remove it

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2022-01-13 09:33:29 +01:00
Koen Vandeputte
2a00054618 ath79: rb912: fix pll init issues
It was reported that some rb912 boards (ar934x) have issues with some ethernet speeds.
Investigation shows that the board failed to adapt the ethernet pll values as shown here:

[    5.284359] ag71xx 19000000.eth: failed to read pll-handle property

added custom prints in code and triggering a link switch:

[   62.821446] Atheros AG71xx: fast reset
[   62.826442] Atheros AG71xx: update pll 2
[   62.830494] Atheros AG71xx: no pll regmap!

Comparison with another very similar board (rb922 - QCA955x) showed a missing
reference clock frequency in dts, which seems to cause a pll init issue.
Unfortunately, no errors are printed when this occurs.

Adding the frequency property fixes the pll init as it can be parsed now
by the ethernet driver.

[   55.861407] Atheros AG71xx: fast reset
[   55.866403] Atheros AG71xx: update pll 2
[   55.870462] Atheros AG71xx: ath79_set_pllval: regmap: 0x81548000, pll_reg: 0x2c, pll_val: 0x02000000

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2022-01-13 09:33:29 +01:00
Oskari Lemmela
fdda3130f2 mikrotik: make soft_config writable
Parent mtd partition needs to be writable

Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
2022-01-13 09:33:29 +01:00
Oskari Lemmela
8441a622ec mikrotik: enable variable size erase
Add support for variable size erase blocks.
Enable it to all targets which has mikrotik targets.

Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
2022-01-13 09:33:29 +01:00
Oskari Lemmela
6eb196ed0f generic: platform/mikrotik: make soft_config writable without 4K sectors
Make soft_config writable in all cases. Performing soft_config commit
will fail if mtd partition is not writable.

Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
[bump rb_softconfig version number]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2022-01-13 09:33:29 +01:00
Koen Vandeputte
2bb7c1db70 imx: bump SDMA firmware to v3.6
No changelog available

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2022-01-13 09:33:29 +01:00
Daniel Golle
f2c3875dfc
generic: deny write to uImage.FIT sub-image partitions
Set policy bit to force read-only mode on uImage.FIT filesystem
sub-images mapped as block partitions by the FIT partition parser.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-01-11 00:06:16 +00:00
David Woodhouse
8cdc356f8c mediatek: mt7623: Re-enable ARM arch timer
CONFIG_ARM_ARCH_TIMER cannot be enabled in the config directly; it is only
selected by CONFIG_HAVE_ARM_ARCH_TIMER. We need to enable the latter in
our config.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fixes: 4f1c5b01c1 ("mediatek: mt7623: backport musb, improve HDMI console")
2022-01-10 13:45:41 +00:00
David Woodhouse
4648a60058 mediatek: mt7623: Disable power button reset for U7623-02 board
The Unielec U7623 doesn't have a physical power button; I think it's hard
wired so that it turns on automatically when power is applied (unlike the
Banana Pi R2 which is a pain).

So the 'reset on long press of power button' behaviour that we get when
we enable the PMIC keyboard driver is kind of unhelpful. Disable it.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fixes: 0d3f3323a2 ("mediatek: mt7623: enable more hardware features")
2022-01-10 13:45:41 +00:00
Sven Eckelmann
97f5617259 ath79: Add support for OpenMesh OM5P-AC v1
Device specifications:
======================

* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi (11n)
* 2T2R 5 GHz Wi-Fi (11ac)
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring
* 2x ethernet
  - eth0
    + AR8035 ethernet PHY (RGMII)
    + 10/100/1000 Mbps Ethernet
    + 802.3af POE
    + used as LAN interface
  - eth1
    + AR8035 ethernet PHY (SGMII)
    + 10/100/1000 Mbps Ethernet
    + 18-24V passive POE (mode B)
    + used as WAN interface
* 12-24V 1A DC
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

   setenv serverip 192.168.1.21
   setenv ipaddr 192.168.1.1
   tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to the
device via

  scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

  sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2022-01-09 21:12:28 +01:00
Sven Eckelmann
72ef594550 ath79: Add support for OpenMesh OM5P-AN
Device specifications:
======================

* Qualcomm/Atheros AR9344 rev 2
* 560/450/225 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 1T1R 2.4 GHz Wi-Fi
* 2T2R 5 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring
* 2x ethernet
  - eth0
    + AR8035 ethernet PHY
    + 10/100/1000 Mbps Ethernet
    + 802.3af POE
    + used as LAN interface
  - eth1
    + 10/100 Mbps Ethernet
    + builtin switch port 1
    + 18-24V passive POE (mode B)
    + used as WAN interface
* 12-24V 1A DC
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

   setenv serverip 192.168.1.21
   setenv ipaddr 192.168.1.1
   tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to the
device via

  scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

  sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2022-01-09 21:12:28 +01:00
Tamas Balogh
b29f4cf34c ath79: add support for ASUS RP-AC66
Asus RP-AC66 Repeater

Hardware specifications:
Board: AP152
SoC: QCA9563
DRAM: 64MB DDR2
Flash: 25l128 16MB SPI-NOR
LAN/WAN: 1x1000M QCA8033
WiFi 5GHz: QCA9880
Clocks: CPU:775.000MHz, DDR:650.000MHz, AHB:258.333MHz, Ref:25.000MHz

MAC addresses as verified by OEM firmware:
use            address   source
Lan/Wan   *:24         art 0x1002 (label)
2G             *:24         art 0x1002
5G             *:26         art 0x5006

Installation:

Asus windows recovery tool:
 - install the Asus firmware restoration utility
 - unplug the router, hold the reset button while powering it on
 - release when the power LED flashes slowly
 - specify a static IP on your computer:
     IP address: 192.168.1.75
     Subnet mask 255.255.255.0
 - Start the Asus firmware restoration utility, specify the factory image
    and press upload
 - Do not power off the device after OpenWrt has booted until the LED flashing.

TFTP Recovery method:
 - set computer to a static ip, 192.168.1.75
 - connect computer to the LAN 1 port of the router
 - hold the reset button while powering on the router for a few seconds
 - send firmware image using a tftp client; i.e from linux:
 $ tftp
 tftp> binary
 tftp> connect 192.168.1.1
 tftp> put factory.bin
 tftp> quit

Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
2022-01-09 20:32:41 +01:00
Fritz D. Ansel
693958497a mediatek mt7622: fix 300mhz typo in dts
The lowest frequency should be 300MHz, since that is the label
assigned to the OPP in the mt7622.dtsi device tree, while there is one
missing zero in the actual value.

To be clear, the lowest frequency should be 300MHz instead of 30MHz.

As mentioned @dangowrt on the OpenWrt forum there is no benefit in
leaving 30MHz as the lowest frequency.

Signed-off-by: Jip de Beer <gpk6x3591g0l@opayq.com>
Signed-off-by: Fritz D. Ansel <fdansel@yandex.ru>
2022-01-09 14:48:16 +00:00
Stefan Lippers-Hollmann
abc2821286 x86: improve sysinfo handling of dummy values
Fall back to using board_vendor and board_name, if known dummy values
are used for sys_vendor and product_name.

Examples:
	To be filled by O.E.M.:To be filled by O.E.M.
-->	INTEL Corporation:ChiefRiver

	System manufacturer:System Product Name
-->	ASUSTeK COMPUTER INC.:P8H77-M PRO

	To Be Filled By O.E.M.:To Be Filled By O.E.M.
-->	ASRock:Q1900DC-ITX

	Gigabyte Technology Co., Ltd.:To be filled by O.E.M.
-->	Gigabyte Technology Co., Ltd.:H77M-D3H

	empty:empty
-->	TYAN Computer Corporation:TYAN Toledo i3210W/i3200R S5211

	To Be Filled By O.E.M.:To Be Filled By O.E.M.
-->	ASRock:H77 Pro4-M

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2022-01-08 23:25:05 +01:00
Alex Lewontin
62a2bfaff8 ipq806x: janitorial work, respect line lengths
This commit breaks up some lines so that they are shorter than
74 charcters.

Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
2022-01-08 23:25:05 +01:00
Alex Lewontin
479acf03cc ipq806x: modularize generic subtarget
This commit moves the device profiles within the ipq806x/generic
subtarget into their own includable .mk file, to support eventually
having subtargets other than generic.

Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
2022-01-08 23:25:05 +01:00
Aleksander Jan Bajkowski
46468fc9d5 lantiq: replace patches with version accepted upstream
Replace recently added patches with version accepted upstream.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-01-08 19:32:45 +01:00
Nick McKinney
e0a574d4b7 ramips: add support for Linksys EA6350 v4
Specifications:
- SoC: MT7621DAT (880MHz, 2 Cores)
- RAM: 128 MB
- Flash: 128 MB NAND
- Ethernet: 5x 1GiE MT7530
- WiFi: MT7603/MT7613
- USB: 1x USB 3.0

This is another MT7621 device, very similar to other Linksys EA7300
series devices.

Installation:

Upload the generated factory.bin image via the stock web firmware
updater.

Reverting to factory firmware:

Like other EA7300 devices, this device has an A/B router configuration
to prevent bricking.  Hard-resetting this device three (3) times will
put the device in failsafe (default) mode.  At this point, flash the
OEM image to itself and reboot.  This puts the router back into the 'B'
image and allows for a firmware upgrade.

Troubleshooting:

If the firmware will not boot, first restore the factory as described
above.  This will then allow the factory.bin update to be applied
properly.

Signed-off-by: Nick McKinney <nick@ndmckinney.net>
2022-01-08 00:49:59 +01:00
Liangkuan Yang
bc7d36ba3a ramips: add support for RAISECOM MSG1500 X.00
RAISECOM MSG1500 X.00 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router.
Apart from the general model, there are two ISP customized models:
China Mobile and China Telecom.

Specifications:

- SoC: Mediatek MT7621AT
- RAM: 256MiB DDR3
- Flash: 128MiB NAND
- Ethernet: 5 * 10/100/1000Mbps: 4 * LAN + 1 * WAN
  - Switch: MediaTek MT7530 (SoC)
- WLAN: 1 * MT7615DN Dual-Band 2.4GHz 2T2R (400Mbps) 5GHz 2T2R (867Mbps)
- USB: 1 * USB 2.0 port
- Button: 1 * RESET button, 1 * WPS button, 1 * WIFI button
- LED: blue color: POWER, WAN, WPS, 2.4G, 5G, LAN1, LAN2, LAN3, LAN4, USB
- UART: 1 * serial port header (4-pin)
- Power: DC 12V, 1A
  - Switch: 1 * POWER switch

MAC addresses as verified by vendor firmware:

use   address             source
LAN   C8:XX:XX:3A:XX:E7   Config   "protest_lan_mac"  ascii  (label)
WAN   C8:XX:XX:3A:XX:EA   Config   "protest_wan_mac"  ascii
5G    C8:XX:XX:3A:XX:E8   Factory  "0x4"              hex
2.4G  CA:XX:XX:4A:XX:E8   [not on flash]

The increment of the 4th byte for the 2.4g address appears to vary.
Reported cases:

       5g                 2.4g         increment
 C8:XX:XX:90:XX:C3  CA:XX:XX:C0:XX:C3  0x30
 C8:XX:XX:3A:XX:08  CA:XX:XX:4A:XX:08  0x10
 C8:XX:XX:3A:XX:E8  CA:XX:XX:4A:XX:E8  0x10

Since increment is inconsistent and there is no obvious pattern
in swapping bytes, and the 2.4g address has local bit set anyway,
it seems safer to use the LAN address with flipped byte here in
order to prevent collisions between OpenWrt devices and OEM devices
for this interface. This way we at least use an address as base
that is definitely owned by the device at hand.

Notes:

1. The vendor firmware allows you to connect to the router by telnet.
   (known version 1.0.0 can open telnet.)
   There is no official binary firmware available.
   Backup the important partitions data:
   "Bootloader", "Config", "Factory", and "firmware".
   Note that with the vendor firmware the memory is detected only 128MiB
   and the last 512KiB in NAND flash is not used.

2. The POWER LED is default on after press POWER switch.
   The WAN and LAN1 - 4 LEDs are wired to ethernet switch.
   The WPS LED is controlled by MT7615DN's GPIO.
   Currently there is no proper way to configure it.

3. At the time of adding support the wireless config needs to be set up
   by editing the wireless config file:

 * Setting the country code is mandatory, otherwise the router loses
   connectivity at the next reboot. This is mandatory and can be done
   from luci. After setting the country code the router boots correctly.
   A reset with the reset button will fix the issue and the user has to
   reconfigure.

 * This is minor since the 5g interface does not come up online although
   it is not set as disabled. 2 options here:

   1- Either run the "wifi" command. Can be added from LuCI in system -
      startup - local startup and just add wifi above "exit 0".

   2- Or add the serialize option in the wireless config file as shown
      below. This one would work and bring both interfaces automatically
      at every boot:

      config wifi-device 'radio0'
          option serialize '1'

      config wifi-device 'radio1'
          option serialize '1'

Flash instructions using initramfs image:

1. Press POWER switch to power down if the router is running.

2. Connect PC to one of LAN ports, and set
   static IP address to "10.10.10.2", netmask to "255.255.255.0",
   and gateway to "10.10.10.1" manually on the PC.

3. Push and hold the WIFI button, and then power up the router.
   After about 10s (or you can call the recovery page, see "4" below)
   you can release the WIFI button.
   There is no clear indication when the router
   is entering or has entered into "RAISECOM Router Recovery Mode".

4. Call the recovery page for the router at "http://10.10.10.1".
   Keep an eye on the "WARNING!! tip" of the recovery page.
   Click "Choose File" to select initramfs image, then click "Upload".

5. If image is uploaded successfully, you will see the page display
   "Device is upgrading the firmware... %".
   Keep an eye on the "WARNING!! tip" of the recovery page.
   When the page display "Upgrade Successfully",
   you can set IP address as "automatically obtain".

6. After the rebooting (PC should automatically obtain an IP address),
   open the SSH connection, then download the sysupgrade image
   to the router and perform sysupgrade with it.

Flash back to vendor firmware:

 See "Flash instructions 1 - 5" above.
 The only difference is that in step 4
 you should select the vendor firmware which you backup.

Signed-off-by: Liangkuan Yang <ylk951207@gmail.com>
2022-01-08 00:49:59 +01:00
Rodrigo Araujo
766733e172 ramips: add support for Joowin WR758AC V1 and V2
This commit adds support for Joowin (aka Comfast) WR758AC V1 and V2
devices.

Both have the same wall AP/repeater form factor and differ only
in the 5Ghz chipset (V1 has MT7662, V2 has MT7663).

OpenWrt developers forum page:
https://forum.openwrt.org/t/87355

Specifications:

 - CPU: MediaTek MT7628AN (580MHz)
 - Flash: 8MB
 - RAM: 64MB DDR2
 - 2.4 GHz: 802.11b/g/n (MT7603)
 - 5 GHz: 802.11ac (V1 has MT7662, V2 has MT7663)
 - Antennas: 4x external single band antennas
 - LAN: 1x 10/100M
 - LED: Wifi 3x blue. Programmable
 - Button: WPS

MAC addresses as verified by OEM firmware:

use address source
LAN *:83 factory 0xe000
2g *:85 factory 0x4
5g *:86 factory 0x8004

How to install:
1- Setup a TFTP server on a machine with IP address 192.168.1.10/24
2- Name the image as `firmware_auto.bin` and place it on the root of the
TFTP server
3- Connect the device via Ethernet, it should pick and flash the image

Signed-off-by: Rodrigo Araujo <araujo.rm@gmail.com>
2022-01-08 00:49:59 +01:00
Rui Salvaterra
536f051b97 kernel: bump 5.10 to 5.10.90
Add and enable a new kconfig knob to disable unprivileged eBPF by default.

Patches automatically rebased.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2022-01-07 22:30:40 +01:00
John Audia
9f08557649 kernel: bump 5.4 to 5.4.170
All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/mt7621

Signed-off-by: John Audia <graysky@archlinux.us>
2022-01-07 22:30:40 +01:00
Daniel Golle
87b6e10c71
mediatek: Clause-45 MDIO patch accepted upstream
To easy future maintainance, replace the local patch with what has been
accepted into net-next and is likely to end up in Linux 5.17.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-01-05 14:33:56 +00:00
Matt Fawcett
b2d769673a qoriq: Expand generic subtarget description
Signed-off-by: Matt Fawcett <mattytap@icloud.com>
[remove trailing whitespace]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-01-05 10:54:59 +02:00
Daniel Golle
ef1a64caf4
mediatek: let mtk_eth_soc MAC announce 2500Base-T mode
To allows Ethernet phys supporting 2500Base-T mode to announce that
speed, enable the corresponding bit in mtk_eth_soc driver.
This should hopefully unlock 2500Base-T speed on the UniFi 6 LR.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-01-05 00:57:43 +00:00
Daniel Golle
6c312d9717
kernel: improve driver support for gen-3 Aquantia Ethernet PHYs
* correctly set system side interface, the original patch was
   errornous and there is a follow-up fix for it
 * enable phy statistics for AQR112(+R/C) and ARQ412
   (ethtool --phy-statistics ethX)

Tested, including phy-statistics, on
 - IEI Puzzle M901 (AQR112, AQR112C, AQR112R)
 - IEI Puzzle M902 (AQR113, AQR112R)
 - Ubiquiti UniFi 6 LR (AQR112C)

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-01-05 00:57:25 +00:00
Paul Spooren
cb85aea869 uml: drop Kernel 5.4
After the switch to Kernel 5.10 the old files are no longer required.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2022-01-04 13:06:03 +01:00
Paul Spooren
02852d5538 uml: switch to Kernel 5.10
Switch over from testing version.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2022-01-04 13:05:13 +01:00
Paul Spooren
4a2cca7824 ipq807x: drop target
The target is in an incomplete state and will not receive Kernel 5.10
support, ego it should be dropped before the next release.

People are working on ipq807x with Kernel 5.15 which is only relevant
for the second next release. Once a working patchset exists the target
can be added again.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2022-01-03 10:36:09 +01:00
Ansuel Smith
1e4469b090 kernel: 5.10: backport qca8k new feature
Backport qca8k new feature:
- Ageing configuration support
- Add 2 missing counter on qca8337
- Convert to regmap
- Standardize define and code with GENMASK AND BITFILED macro
- Add mdb add/del support

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2022-01-03 01:00:04 +01:00
Ansuel Smith
5cf198f764 kernel: 5.10: backport additional qca8k fixes
Backport 3 additional fixes for qca8k.
- Fix MTU calculation
- Fix a bug with config set to the wrong PAD when secondary cpu port is defined.
- Fix redundant check in parse_port_config

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2022-01-03 01:00:04 +01:00
Rui Salvaterra
2bb02ccae3 kernel: bump 5.10 to 5.10.89
Deleted (upstreamed):
bcm27xx/patches-5.10/950-0186-pinctrl-bcm2835-Change-init-order-for-gpio-hogs.patch [1]
sunxi/patches-5.10/103-arm64-dts-allwinner-orangepi-zero-plus-fix-PHY-mo.patch [2]

[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.89&id=ba696b470839d70c6b8290c1f798bac7fb2a584c
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.89&id=93a957bbf46ceb224b959de61fe85cfc6f71b6c7

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2022-01-03 01:00:03 +01:00
John Audia
7bf62e2451 kernel: bump 5.4 to 5.4.169
All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/mt7621*

*Had to revert 7f1edbd in order to build due to FS#4149

Signed-off-by: John Audia <graysky@archlinux.us>
2022-01-03 01:00:03 +01:00
Stefan Lippers-Hollmann
d9c2b0cfdd ipq806x: ASRock g10: fix bogus read errors
Properly declare that the g10 is booting from NAND and define its
correct (larger than on other devices-) boot_pages_size, to prevent
the kernel from constantly falling over missing OOB error correction
for the bootloader.

This patch prevents a constant slew of (bogus) read errors reported
by the kernel and keeping the CPU busy and fixes:

blk_update_request: I/O error, dev mtdblock0, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 0
blk_update_request: I/O error, dev mtdblock0, sector 8 op 0x0:(READ) flags 0x80700 phys_seg 3 prio class 0
blk_update_request: I/O error, dev mtdblock0, sector 16 op 0x0:(READ) flags 0x80700 phys_seg 2 prio class 0
blk_update_request: I/O error, dev mtdblock0, sector 24 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0
blk_update_request: I/O error, dev mtdblock0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
Buffer I/O error on dev mtdblock0, logical block 0, async page read
blk_update_request: I/O error, dev mtdblock0, sector 32 op 0x0:(READ) flags 0x80700 phys_seg 8 prio class 0
blk_update_request: I/O error, dev mtdblock0, sector 40 op 0x0:(READ) flags 0x80700 phys_seg 7 prio class 0
blk_update_request: I/O error, dev mtdblock0, sector 48 op 0x0:(READ) flags 0x80700 phys_seg 6 prio class 0
blk_update_request: I/O error, dev mtdblock0, sector 56 op 0x0:(READ) flags 0x80700 phys_seg 5 prio class 0
blk_update_request: I/O error, dev mtdblock0, sector 64 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 0
Buffer I/O error on dev mtdblock0, logical block 1, async page read
Buffer I/O error on dev mtdblock1, logical block 0, async page read
Buffer I/O error on dev mtdblock1, logical block 1, async page read
Buffer I/O error on dev mtdblock2, logical block 0, async page read
Buffer I/O error on dev mtdblock2, logical block 1, async page read
Buffer I/O error on dev mtdblock3, logical block 0, async page read
Buffer I/O error on dev mtdblock3, logical block 0, async page read
Buffer I/O error on dev mtdblock4, logical block 0, async page read
Buffer I/O error on dev mtdblock4, logical block 1, async page read

Suggested-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2022-01-02 20:41:50 +01:00
Shiji Yang
86d019d116 ramips: add ASUS RT-AC1200GU as alt name
RT-AC57U and RT-AC1200GU are the same models sold in different countries.
The purpose of this commit is to allow users to easily find the
corresponding firmware through the model number on the device label.

More specifications: 14e0e4f138 ("ramips: add support for ASUS RT-AC57U")

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[reword commit title/message]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-02 01:31:02 +09:00
Sungbo Eo
a1deab0ec9 ramips: add support for ipTIME T5004
ipTIME T5004 is a 5-port Gigabit Ethernet router, based on MediaTek MT7621A.

Specifications:
* SoC: MT7621AT
* RAM: 128 MiB
* Flash: NAND 128 MiB
* Ethernet: 5x 1GbE
  * Switch: SoC built-in
* UART: J4 (57600 baud)
  * Pinout: [3V3] (TXD) (RXD) (GND)

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware via recovery mode:
1.  Press reset button, power up the device, wait >15s for CPU LED
    to stop blinking.
2.  Upload stock image to TFTP server at 192.168.0.1.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-02 00:50:43 +09:00
Raylynn Knight
2e1206ad23 x86: add/improve support for Sophos SG/XG products
* Add support for Sophos SG/XG-115 r1, r2 with/without wireless
* Add support for Sophos SG/XG-125 r1, r2 with/without wireless
* Add wireless support for SG/XG-105

Signed-off-by: Raylynn Knight <rayknight@me.com>
2021-12-29 22:55:16 +01:00
Jinfan Lei
3928f6ae5c ath79: add usb-phy-analog to reset list in qca953x.dtsi
On startup the USB of QCA9531 board can't be initialized successfully.

lsusb result as below:
root@OpenWrt:~# lsusb unable to initialize libusb: -99

This is because usb-phy-analog is not added to reset list.

Signed-off-by: Jinfan Lei <153869379@qq.com>
(added linebreaks and small little changes to the commit message)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-29 22:55:16 +01:00
Nick Hainke
83b5fbddf2 kernel: 5.10: add patches to fix macronix flash
mtd: spi-nor: locking support for MX25L6405D

Macronix MX25L6405D supports locking with four block-protection bits.
Currently, the driver only sets three bits.  If the bootloader does not
sustain the flash chip in an unlocked state, the flash might be
non-writeable. Add the corresponding flag to enable locking support with
four bits in the status register.

mtd: spi-nor: disable 16-bit-sr for macronix

Macronix flash chips seem to consist of only one status register.
These chips will not work with the "16-bit Write Status (01h) Command".
Disable SNOR_F_HAS_16BIT_SR for all Macronix chips.

Refreshed:
- 0052-mtd-spi-nor-use-4-bit-locking-for-MX25L12805D.patch

Fixes: 15aa53d7ee ("ath79: switch to Kernel 5.10")

Signed-off-by: Nick Hainke <vincent@systemli.org>
2021-12-29 22:55:16 +01:00
WonJung Kim
2dde2416e1 ramips: add support for ipTIME A3004T
ipTIME A3004T is a 2.4/5GHz band router, based on Mediatek MT7621.

Specifications:
 - SoC: MT7621 (880MHz)
 - RAM: DDR3 256M
 - Flash: NAND 128MB  (Macronix NAND 128MiB 3,3V 8-bit)
 - WiFi:
   - 2.4GHz: MT7615E
   - 5GHz : MT7615E
 - Ethernet:
   - 4x LAN
   - 1x WAN
 - USB: 1 * USB3.0 port
 - UART:
   - 3.3V, TX, RX, GND / 57600 8N1

Installation via web interface:
 1. Flash initramfs image using OEM's Recovery mode
 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
 - Flash stock firmware via OEM's Recovery mode

How to use OEM's Recovery mode:
 1. Power up with holding down the reset key until CPU LED stop blinking.
 2. Set fixed ip with `192.168.0.2` with subnet mask `255.255.255.0`
 3. Flash image via tftp to `192.168.0.1`

Additional Notes:
 This router shares one MT7915E chip for both 2.4Ghz/5Ghz.
 radio0 will not working on 5Ghz as it's not connected to the antenna.

Signed-off-by: WonJung Kim <git@won-jung.kim>
(added led dt-bindings)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-29 20:35:57 +01:00
Sungbo Eo
482a7e23a4 ramips: add support for WeVO AIR DUO
WeVO AIR DUO is a 1-bay NAS & 802.11ac (Wi-Fi 5) router, based on
MediaTek MT7620A.

Specifications:
* SoC: MT7620A
* RAM: 64 MiB
* Flash: SPI NOR 16 MiB
* USB & SATA bridge controller: JMicron JMS567
  * SATA 6Gb/s: 2.5" drive slot
  * USB 3.0: Micro-B
  * USB 2.0: connected to SoC
* Wi-Fi:
  * 2.4 GHz: SoC built-in
  * 5 GHz: MT7612EN
* Ethernet: 5x 1GbE
  * Switch: MT7530WU
* UART: 4-pin 1.27 mm pitch through-hole (57600 baud)
  * Pinout: (3V3)|(RXD) (TXD) (GND)

Notes:
* The drive is accessible through the external USB port only when the
  router is turned off.

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
    The image filename should have ".upload" extension.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2021-12-29 20:35:57 +01:00
Torsten Duwe
7ea9936f7f bcm27xx: add AMP2 to HifiBerry DAC+ / DAC+ Pro package
According to the vendor [1] these HATs share the same DT overlay:
hifiberry-dacplus. The PCM512x-compatible control unit is attached to
I2C, so the additional snd-soc-pcm512x-i2c kernel module is required.
Also explicitly note the Amp2 support to reduce confusion for those
users.

[1] <https://www.hifiberry.com/docs/software/configuring-linux-3-18-x/>
Signed-off-by: Torsten Duwe <duwe@lst.de>
(added bcm27xx tag, changed commit message)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-29 20:35:57 +01:00
Pawel Dembicki
afd7ec3b57 kirkwood: add support for two clones from Endian
They are Endian 4i Edge 200 and his clone Endian UTM Mini.

Hardware:
  - SoC: Marvell 88F6281-A1 ARMv5TE Processor 1.2GHz
  - Ram: 512MB (4x Nanya NT5TU128M8GE-AC)
  - NAND Flash: 512MB (Micron 29F4G08AAC)
  - Lan 1-4: 4x GBE (Marvell 88E6171R-TFJ2)
  - Lan 5: 1x GBE (Marvell 88E1116R-NNC1)
  - Storage: MicroSD Slot
  - WLAN: MiniPCIe Slot present, and fitted with SparkLan WPEA-110N/E
          (Atheros AR9280 chipset) (ONLY Endian UTM Mini WLAN)
  - USB: 1x USB 2.0 port
  - Console: RJ-45 port
  - LEDs: 3x GPIO controlled

Notes:
  - WLAN led (Endian UTM Mini) is drived by MPCIE card

Installation by TFTP + serial:
  - Setup TFTP server and copy initramfs image
  - Connect serial console
  - Stop booting in u-boot
  - Do:
	setenv bootargs 'console=ttyS0,115200n8 earlyprintk'
	saveenv
	setenv serverip 192.168.1.1
	setenv ipaddr 192.168.1.2
	tftpboot 0x1200000 openwrt-kirkwood-endian_4i-edge-200-initramfs-uImage
	bootm 0x1200000
  - copy sysupgrade image via ssh.
  - run sysupgrade

Installation by USB + serial:
  - Copy initramfs image to fat32 usb drive
  - Connect pendrive to USB 2.0 front socket
  - Connect serial console
  - Stop booting in u-boot
  - Do:
	setenv bootargs 'console=ttyS0,115200n8 earlyprintk'
        saveenv
	usb reset
	fatload usb 0:1 0x1200000 openwrt-kirkwood-endian_4i-edge-200-initramfs-uImage
	bootm 0x1200000
  - copy sysupgrade image via ssh.
  - run sysupgrade

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2021-12-29 20:35:57 +01:00
Pawel Dembicki
4e46ae1f69 kirkwood: add support for NETGEAR ReadyNAS Duo v2
NETGEAR ReadyNAS Duo v2 is a NAS based on Marvell kirkwood SoC.

Specification:
 - Processor Marvell 88F6282 (1.6 GHz)
 - 256MB RAM
 - 128MB NAND
 - 1x GBE LAN port (PHY: Marvell 88E1318)
 - 1x USB 2.0
 - 2x USB 3.0
 - 2x SATA
 - 3x button
 - 5x leds
 - serial on J5 connector accessible from rear panel
   (115200 8N1) (VCC,TX,RX,GND) (3V3 LOGIC!)

Installation by USB + serial:
  - Copy initramfs image to fat32 usb drive
  - Connect pendrive to USB 2.0 front socket
  - Connect serial console
  - Stop booting in u-boot
  - Do:
	usb reset
        setenv bootargs 'console=ttyS0,115200n8 earlyprintk'
        setenv bootcmd 'nand read.e 0x1200000 0x200000 0x600000;bootm 0x1200000'
        saveenv
	fatload usb 0:1 0x1200000 openwrt-kirkwood-netgear_readynas-duo-v2-initramfs-uImage
	bootm 0x1200000
  - copy sysupgrade image via ssh.
  - run sysupgrade

Installation by TFTP + serial:
  - Setup TFTP server and copy initramfs image
  - Connect serial console
  - Stop booting in u-boot
  - Do:
	setenv bootargs 'console=ttyS0,115200n8 earlyprintk'
	setenv bootcmd 'nand read.e 0x1200000 0x200000 0x600000;bootm 0x1200000'
	saveenv
	setenv serverip 192.168.1.1
	setenv ipaddr 192.168.1.2
	tftpboot 0x1200000 openwrt-kirkwood-netgear_readynas-duo-v2-initramfs-uImage
	bootm 0x1200000
  - copy sysupgrade image via ssh.
  - run sysupgrade

Known issues:
  - Power button and PHY INTn pin are connected to the same GPIO. It
    causes that every network restart button is pressed in system.
    As workaround, button is used as regular BTN_1.

For more info please look at file:
RND_5.3.13_WW.src/u-boot/board/mv_feroceon/mv_hal/usibootup/usibootup.c
from Netgear GPL sources.

Tested-by: Raylynn Knight <rayknight@me.com>
Tested-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2021-12-29 20:35:57 +01:00
Pawel Dembicki
4e82a80b68 kernel: generic: backport linkstation-poweroff driver
Linkstation poweroff driver was added to mvebu target, but is required
for kirkwood target too.
This commit make two changes:
- move linkstation-poweroff support patch from mvebu to generic and
replace upstream accepted version
- backport small linkstation-poweroff fix from 5.12

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2021-12-29 20:35:57 +01:00
David Bauer
79a81d36ae ath79: remove pre-5.10 specific kernel code
With Kernel 5.4 support removed, we can get rid of this legacy code.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-12-29 03:44:56 +01:00
David Bauer
00b194871c ramips: aw9523: add can_sleep flag for GPIO chip
The GPIO expander is connected via I2C, thus the can_sleep flag has to
be set to true. This should fix spurious "scheduling while atomic" bugs
in the kernel ringbuffer.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-12-29 03:43:03 +01:00
Daniel Golle
92820cc5b9
mediatek: yet again, replace patch with updated pending patch
Upon comment of Russell King ('Oh no, not this "-1 disease" again.')
clean up mdio read and write return type and value in mtk_eth_soc
driver and also use appropriate return values for bus-busy-timeout-
errors in newly added Clause 45 access code.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-27 20:20:10 +00:00
Daniel Golle
c555c34dd1
mediatek: replace patch with version sent upstream
Replace recently added patch
 701-net-ethernet-mtk_eth_soc-add-support-for-clause-45-mdio.patch
with version sent upstream
 701-net-ethernet-mtk_eth_soc-implement-Clause-45-MDIO-access.patch

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-27 16:24:23 +00:00
Sergey Ryazanov
5deb3996e2 ath25: add kernel 5.10 support
Copy and refresh patches and config from 5.4 to 5.10. Most patches
require no more then automatic refresh. The only exception is the
Ethernet driver patch, which requires some more work:
* drop eth_change_mtu() usage since it was removed from the kernel,
  it anyway useless for drivers that utilizes alloc_etherdev();
* add the txqueue number argument to the .ndo_tx_timeout callback
  function;
* replace ioremap_nocache() which was finally removed from the kernel by
  the ioremap() with the same behaviour.

Switch target to the new kernel version.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[use KERNEL_TESTING_PATCHVER for now]
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2021-12-27 16:00:21 +00:00
Sergey Ryazanov
5bf8ae7c4b ath25: refresh kernel 5.4 config
The target config require some refresh due to the just introduced
filtering of the "run-time" options, MIPS eBPF JIT backporting, and so
on.

The configuration is easily updated using make kernel_oldconfig. So
let's update it now in preparation for v5.10 support to reduce the new
kernel configuration diff.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2021-12-27 16:00:21 +00:00
Sergey Ryazanov
0b2c1d8b9a Move mvswitch 88E6060 driver to the ath25
ath25 requires a 88E6060 driver to support boards such as Fonera 2.0g
(FON2202). The swconfig based mvswitch driver has not yet been ported to
the 5.10 kernel as the only user is the ath25 target while all other
targets have been switched to the upstream DSA implementation.

Switching ath25 to the DSA implementation is a complex task, since we
need either per-board platform data or DTS support. ath25 lacks both of
them and builds only a single generic image. So we need to keep the
swconfig driver implementation to easly and quickly port ath25 to the
5.10 kernel.

Since porting the mvswitch driver to 5.10 as a generic driver is not an
option, and since the ath25 is its only user, make mvswitch a target
specific driver to be able to port it to the 5.10 kernel as part of the
kernel version update of the target. This will allow us quickly migrate
to the next kernel version and not delay the next firmware release.

Suggested-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2021-12-27 16:00:21 +00:00
Rui Salvaterra
a3774d72c8 kernel: bump 5.10 to 5.10.88
Deleted (upstreamed):
mpc85xx/patches-5.10/002-powerpc-85xx-fix-oops-when-CONFIG_FSL_PMC-n.patch [1]

[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.88&id=151ffac3ac277ad7c2a5f201b566b56d97ed3a99

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-12-27 16:00:21 +00:00
Christian Lamparter
0e841fd4a2 apm821xx: remove broken PCIe MSI support
These never worked and upstream is in the process of removing
them as well. Legacy PCI interrupt signaling is still working
as before.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-27 13:55:10 +01:00
Christian Lamparter
4e6ebdd7ce apm821xx: remove overlapping partitions
Apart from the dtb partition, these were all "read-only;"
they serve no purpose other than being a copy of what
netgear had defined in their original firmware.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-27 13:55:10 +01:00
Christian Lamparter
832b9cbd74 apm821xx: fix WD MyBook Live DUO USB-Port
where to begin? the USB regulator settings were just
a part of the issue. With them changed, according to
the forum it still failed when a USB device was
connected to the port with:

dwc2 4bff80000.usbotg: dwc2_restore_global_registers: no global registers to restore
dwc2 4bff80000.usbotg: dwc2_exit_partial_power_down: failed to restore registers
dwc2 4bff80000.usbotg: exit partial_power_down failed
dwc2 4bff80000.usbotg: HC died; cleaning up

One clue was found upstream in
commit cc10ce0c51b1 ("usb: dwc2: disable power_down on Amlogic devices")

|Disable power_down by setting the parameter to
|DWC2_POWER_DOWN_PARAM_NONE. This fixes a problem on various Amlogic
|Meson SoCs where USB devices are only recognized when plugged in before
|booting Linux. A hot-plugged USB device was not detected even though the
|device got power (my USB thumb drive for example has an LED which lit
|up).
|[...]

the same method proposed there worked with APM821xx's USB IP-Core.

Link: https://forum.openwrt.org/t/wd-my-book-duo-usb/111926/2
Reported-by: thwe and takimata (openwrt forum)
Fixes: b70d3557e0 ("apm821xx: clean up gpio-hogs")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-27 13:55:10 +01:00
Christian Lamparter
2593d510e2 apm821xx: drop 5.4 config and patches
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-27 13:51:41 +01:00
Sander Vanheule
ebc0ce118f realtek: netgear-gs110tpp: Add system LEDs
The GS110TPP has an RGB LED used for system status indication. Expose
all three components as separate GPIO LEDs connected via the device's
RTL8231.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2021-12-27 13:51:41 +01:00
Sander Vanheule
c88124cfc4 realtek: netgear-gigabit: Enable RTL8231
Since the move to 5.10, there are now two GPIO drivers. The gpio0 node
refers to the internal GPIOs, so the indirect-access-bus-id is no longer
relevant for that node.

Set indirect-access-bus-id to the correct value (31) on the correct node
(gpio1) and enable the device.

Cc: Raylynn Knight <rayknight@me.com>
Cc: Michael Mohr <akihana@gmail.com>
Cc: Stijn Segers <foss@volatilesystems.org>
Cc: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Bjørn Mork <bjorn@mork.no>
2021-12-27 13:51:41 +01:00
Ansuel Smith
5761aa4d9e kernel: mtd: parsers: add nvmem support to cmdlinepart
Assuming cmdlinepart is only one level deep partition scheme and that
static partition are also defined in DTS, we can assign an of_node for
partition declared from bootargs.

The cmdlinepart parser is the first parser checked and if it does find
some partition declared in the bootargs, every other parser is ignored.
This means that the fixed-partition parser is ignored and an of_node for
the mtd is never assigned.
Fix this by searching a defined of_node using a similar fixed_partition
parsing logig, check if a partition is present with the same label, check
that it has the same offset and size and finally assign an of_node to the
mtd. The NVMEM can now find the of_node for the mtd and correctly works.

Fixes: abc17bf306 ("ath79: convert mtd-mac-address to nvmem implementation")
Tested-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2021-12-27 13:51:41 +01:00
David Bauer
e1780de5ce rockchip: remove Kernel 5.4
As v5.10 is the default kernel version now, the files for v5.4 can be
dropped.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-12-27 03:13:36 +01:00
David Bauer
13f326de3a mpc85xx: remove kernel 5.4
As v5.10 is the default kernel version now, the files for v5.4 can be
dropped.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-12-27 03:13:36 +01:00
David Bauer
9d9d851eec ath79: remove kernel 5.4
Signed-off-by: David Bauer <mail@david-bauer.net>
2021-12-27 03:13:36 +01:00
Nick Hainke
cfa670bf16 ath79: add missing UBNT_REVISION
The UBNT_REVISION was already added for the ubnt-xw target because:

  U-boot bootloader on M-XW devices expects factory image revision
  version in specific format. On airOS v6.1.7 with `U-Boot 1.1.4-s1039
  (May 24 2017 - 15:58:18)` bootloader checks if the revision major(?)
  number is actually a number, but in currently generated images there's
  OpenWrt text and so the check fails

  ...

  By placing arbitrary correct number first in major version, we make the
  bootloader happy and we can flash factory images over TFTP again.

  commit d42a7c4699 ("ath79: ubnt-m-xw: Fix factory image flashing using TFTP recovery method")

Fixes errors in the form of (tftp flashing):
  sent DATA <block=8577, 412 bytes>
  received ERROR <code=2, msg=Firmware check failed>
  Error code 2: Firmware check failed

The missing UBNT_REVISION was not noticed before, since the
UBNT_REVISION field for the ubnt-xm target was also set to:
  "42.OpenWrt-..."
Probably, UBNT_REVISION for the ubnt-xm target was set by the ubnt-xw
and was never overridden somewhere else. However, it is missing and
should be part of the ubnt-xm device.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2021-12-27 03:07:22 +01:00
Hauke Mehrtens
0dc4ab344b sunxi: Use rtl8723bu-firmware instead of rtl8723bs-firmware
The firmware for the rtl8723bs chip is now included in the
rtl8723bu-firmware package.

Fixes: 397dfe4a97 ("linux-firmware: Update to version 20121216")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-12-27 00:58:29 +01:00
Daniel Golle
8b6d6f28c1
mediatek: mt7622: unifi6lr: properly register Ethernet PHY
This change enables proper Ethernet link status and speed reporting on
the Ubiquiti UniFi 6 LR access point:

 mtk_soc_eth 1b100000.ethernet eth0: PHY [mdio-bus:08] driver [Aquantia AQR112C] (irq=POLL)
 mtk_soc_eth 1b100000.ethernet eth0: configuring for phy/2500base-x link mode
 mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-26 19:11:54 +00:00
Daniel Golle
e6c08c8272
mediatek: mt7622: enable driver for Aquantia PHYs
Enable Aquantia Ethernet PHY driver as there is an AQR112C 2500Base-T
PHY in the Ubiquiti UniFi 6 LR access point.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-26 19:11:49 +00:00
Daniel Golle
13b3474294
mediatek: add support for Clause 45 MDIO access
Add support for Clause 45 MDIO PHY register read and write operations
to mtk_eth_soc driver.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-26 19:11:43 +00:00
Daniel Golle
215c78eef5
kernel: generic: refresh patch
722-net-phy-aquantia-Add-AQR113-driver-support.patch needs refresh.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-26 19:11:36 +00:00
Rafał Miłecki
65974aa18b bcm4908: include ATF in bootfs images
It's required for proper booting.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-12-24 23:07:39 +01:00
Daniel Golle
f9782f5bcd
mvebu: puzzle: wan LED and fix default network
Fix default network configuration of the Puzzle-M902 so all LAN ports
are included in the LAN bridge.
Setup network LED to indicate WAN port link status, like vendor
firmware does as well.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-23 20:17:47 +00:00
Daniel Golle
f81a06408e
mvebu: enable Aquantia phy driver for Puzzle devices
Fixes Ethernet link status on all ports and makes 2.5G ports usable
in 2.5G and 1G full-duplex mode.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-23 20:17:42 +00:00
Daniel Golle
7b9d2d6f7b
kernel: add id for AQR112 Ethernet phy variants
Add ids for AQR112R and AQR112C 2.5G Ethernet PHYs.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-23 20:17:37 +00:00
Daniel Golle
73c0ef1ecf
kernel: import patch enabling AQR113 PHY
Add PHY ID for the Aquantia AQR113 PHY.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-23 20:17:32 +00:00
Daniel Golle
6563a6a3ba
kernel: import patch enabling AQR112 and AQR412 PHY
Copy and refresh patch enabling AQR112 and AQR412 Ethernet PHY from
layerscape (5.4) target to generic (5.10) as AQR112 can also be found
on other targets as well.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-23 20:17:28 +00:00
Daniel Golle
962c585580
mvebu: remove accidentally added file
Remove accidentally added file (which was a left-over of a by-now
replaced driver)

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-21 23:44:45 +00:00
Daniel Golle
3684b494dd
mvebu: puzzle-m901: add LEDs, fan and reset button
Wire up MCU driver for LEDs, fan and temperature sensor, and add
GPIO reset button just like on the M902 also on the Puzzle M901.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-21 21:54:54 +00:00
Daniel Golle
ddad936fc6
mvebu: puzzle-m902: add GPIO reset button
Add reset button to device tree so it has the function expected from
usual OpenWrt devices.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-21 21:54:49 +00:00
Daniel Golle
7e4c1cca8a
mvebu: puzzle-mcu: improve led driver
Set blinking mode using scheduled work instead of blocking which may
result in deadlocks.
Add dynamic kprintf debugging hexdumps of all MCU rx and tx.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-21 21:54:42 +00:00
Paul Spooren
15aa53d7ee ath79: switch to Kernel 5.10
Kernel 5.10 is used by many people since quite a while. With other
targets already moved to 5.10, let ath79 follow suit.

Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ath79/tl-wdr3600; ath79/tl-wdr4300]
Tested-by: Aleksander Jan Bajkowski <olek2@wp.pl> [ath79/tl-wdr4300]
Signed-off-by: Paul Spooren <mail@aparcar.org>
Signed-off-by: David Bauer <mail@david-bauer.net>
2021-12-21 21:38:52 +01:00
Stijn Tintel
3fda16078b qoriq: add support for WatchGuard Firebox M300
This device is based on NXP's QorIQ T2081QDS board, with a quad-core
dual-threaded 1.5 GHz ppc64 CPU and 4GB ECC RAM. The board has 5
ethernet interfaces, of which 3 are connected to the ethernet ports on
the front panel. The other 2 are internally connected to a Marvell
88E6171 switch; the other 5 ports of this switch are also connected to
the ethernet ports on the front panel.

Installation: write the sdcard image to an SD card. Stock U-Boot will
not boot, wait for it to fail then run these commands:

setenv OpenWrt_fdt image-watchguard-firebox-m300.dtb
setenv OpenWrt_kernel watchguard_firebox-m300-kernel.bin
setenv wgBootSysA 'setenv bootargs root=/dev/mmcblk0p2 rw rootdelay=2 console=$consoledev,$baudrate fsl_dpaa_fman.fsl_fm_max_frm=1530; ext2load mmc 0:1 $fdtaddr $OpenWrt_fdt; ext2load mmc 0:1 $loadaddr $OpenWrt_kernel; bootm $loadaddr - $fdtaddr'
saveenv
reset

The default U-Boot boot entry will now boot OpenWrt from the SD card.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-12-21 21:37:46 +02:00
Stijn Tintel
080a769b4d qoriq: new target
Add a new target named "qoriq", that will support boards using PowerPC
processors from NXP's QorIQ brand.

This doesn't actually add support for any board yet, so that
installation instructions can go in the commit message of the commit
that adds actual support for a board.

Using CONFIG_E6500_CPU here due to the kernel using -mcpu=powerpc64
rather than -mcpu=e5500 when selecting CONFIG_E5500_CPU. The only
difference between e5500 and e6500 is AltiVec support, and the kernel
checks for it at runtime. Musl will only check at runtime if AltiVec
support is disabled at compile-time, so we need to use e5500 in CPU_TYPE
to avoid SIGILL.

Math emulation (CONFIG_MATH_EMULATION_HW_UNIMPLEMENTED) is required, as
neither e5500 nor e6500 implement fsqrt nor fsqrts, and musl hardcodes
sqrt and sqrtf to use these ASM instructions on PowerPC64.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reviewed-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-12-21 21:37:39 +02:00
Daniel Golle
f0c0b18234
mvebu: puzzle-m902: add driver for MCU driving LEDs, fan and buzzer
Backport MFD driver for communicating with the on-board MCU found on
IEI World Puzzle appliances.
Improve the driver to support multiple LEDs, apply a default state and
let MCU take care of blinking if timing is within supported range.
Wire up LEDs and fan for Puzzle M902 in device tree.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-21 16:41:10 +00:00
David Bauer
b1d483b865 ramips: work around duplicate MAC address on U6 Lite
The UniFi 6 Lite has two MAC addresses for the 2.4 and 5GHz radio in
it's EEPROM partition.

On my unit these are

F4 92 BF A0 BB 6F
F6 92 BF A0 BB 6F

The problem with these is that mac80211 increases the first octet by
2, which leads to conflicting MAC addresses between radios.

Work around this problem for now by increasing the last octet by 1 on
the 5 GHz radio.

Ubiquiti increases the last octet by 2 for each subsequent VAP created
per radio. Ideally we should do the same, however this functionality is
currently lacking from mac80211.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-12-20 00:12:12 +01:00
Daniel Golle
5a4685cfa2
mediatek: mt7623: bpi-r2: add ethernet alias to device tree
Add ethernet0 alias in device tree to make U-Boot inherit the Ethernet
mac address (set via environment variable 'ethaddr') down to Linux.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-18 01:52:19 +00:00
Sergey Ryazanov
fa3690f8f1 kernel: 5.10: consolidate mac80211 crypto options
Each of
- CRYPTO_AEAD2
- CRYPTO_AEAD
- CRYPTO_GF128MUL
- CRYPTO_GHASH
- CRYPTO_HASH2
- CRYPTO_HASH
- CRYPTO_MANAGER2
- CRYPTO_MANAGER
- CRYPTO_NULL2

either directly required for mac80211 crypto support, or directly
selected by such options. Support for the mac80211 crypto was enabled in
the generic config since c7182123b9 ("kernel: make cryptoapi support
needed by mac80211 built-in"). So move the above options from the target
configs to the generic config to make it clear why do we need them.

CC: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2021-12-17 16:16:34 +01:00
Sergey Ryazanov
b61ab8f57e kernel: filter out both Clang and LLD versions
Both CLANG_VERSION and LLD_VERISON are autogenerated runtime
configuration options, so add them to the kernel configuration filter
and remove from generic and per-target configs to keep configs clean.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2021-12-17 16:16:34 +01:00
John Audia
43c0a12665 kernel: bump 5.10 to 5.10.85
Removed target for patch which does not exist:
    bcm27xx/patches-5.10/950-0249-kbuild-Disable-gcc-plugins.patch

All patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, ipq806x/R7800*
Run-tested: bcm2711/RPi4B, ipq806x/R7800*

* Had to revert 7f1edbd412 in order to build
  (binutils 2.37, https://bugs.openwrt.org/index.php?do=details&task_id=4149)

Signed-off-by: John Audia <graysky@archlinux.us>
2021-12-17 15:10:22 +01:00
John Audia
187c8f9153 kernel: bump 5.10 to 5.10.84
All patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B
Run-tested: bcm2711/RPi4B

Signed-off-by: John Audia <graysky@archlinux.us>
2021-12-17 15:10:22 +01:00
John Audia
d4b25007ea kernel: bump 5.4 to 5.4.167
All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/mt7621*

*FS#4149 affects me so I had to revert 7f1edbd412
in order to downgrade to 2.35.1

Signed-off-by: John Audia <graysky@archlinux.us>
2021-12-17 15:10:22 +01:00
John Audia
61c76f836f kernel: bump 5.4 to 5.4.166
All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/mt7621*

*FS#4149 affects me so I had to revert 7f1edbd412
in order to downgrade to 2.35.1

Signed-off-by: John Audia <graysky@archlinux.us>
2021-12-17 15:10:22 +01:00
John Audia
a696e325f7 kernel: bump 5.4 to 5.4.165
All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/mt7621*

*FS#4149 affects me so I had to revert 7f1edbd412
in order to downgrade to 2.35.1

Signed-off-by: John Audia <graysky@archlinux.us>
2021-12-17 15:10:22 +01:00
Sungbo Eo
cc3e390a74 ramips: mt7620: tidy up 02_network
* fix alphabetic sorting
* consolidate duplicate cases

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2021-12-16 22:28:58 +09:00
Rafał Miłecki
444b4ea4a4 bcm4908: add uboot-envtools to default packages
It's required by sysupgrade to access UBI metadata partitions.

Fixes: 5f05795aa7 ("bcm4908: sysupgrade: add pkgtb format support")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-12-16 08:26:25 +01:00
Rafał Miłecki
85ad48c957 kernel: backport support for multicolor & RGB LEDs to 5.4
This is a requirement for backporting DT files defining such LEDs.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-12-16 07:18:05 +01:00
Felix Fietkau
01bebc070c kernel: backport the upstream implementation of threaded NAPI to 5.4
The workqueue based implementation has a few corner cases and typically lower
performance than the upstream one

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-12-15 20:36:22 +01:00
Rui Salvaterra
c772783394 ramips: remove Linux 5.4 support
We're at 5.10 stable, this can finally go.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-12-15 09:40:03 +00:00
David Bauer
07452a680b ramips: fix Tenbay T-MB5EU v1 Wireless MAC
It was reported, that Tenbay T-MB5EU v1 do have incorrect Wireless MAC
address set on 2.4 and 5 GHz.

Some boards do not seem to have the correct MAC address set for the
external PHY of the MT7915 radio at caldata offset 0xa.

As the external PHY does not expose a DT binding (yet), fix up the mac
address in userspace.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-12-15 00:13:40 +01:00
Rafał Miłecki
30b93672ec bcm4908: add fdt-utils to default packages
It's required by sysupgrade.

Fixes: 5f05795aa7 ("bcm4908: sysupgrade: add pkgtb format support")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-12-14 17:58:20 +01:00
Martin Schiller
60881f657d layerscape: armv7: refresh config-5.10
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2021-12-13 23:22:29 +01:00
Martin Schiller
7af83d2c03 layerscape: armv7: copy config-5.4 to config-5.10
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2021-12-13 23:22:29 +01:00
Martin Schiller
fef79a5dc4 layerscape: armv8_64b: refresh config-5.10
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2021-12-13 23:22:29 +01:00
Martin Schiller
a939015dd1 layerscape: armv8_64b: copy config-5.4 to config-5.10
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2021-12-13 23:22:29 +01:00
Martin Schiller
83035a44a7 layerscape: armv8_64b: use non-SDK dts files for linux-5.10 or newer
Since we decided to drop the LSDK patches with linux-5.10, we now have
to switch to the corresponding upstream dts files as well.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2021-12-13 23:22:29 +01:00
Martin Schiller
82ce460ab1 layerscape: armv8_64b: fix KERNEL_LOADADDR for linux >= 5.8
In kernel versions newer than 5.8 the arm64 TEXT_OFFSET (0x80000) has
been set to 0x0 (and later removed). This will break Uimages with kernel
load addresses that aren't 2MiB aligned any longer. Resulting in the
kernel silently fail to boot. For layerscape armv8_64b targets this
needs to be changed to 0x80000000 (start of RAM).

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2021-12-13 23:22:29 +01:00
Martin Schiller
68b4e9fe0e layerscape: add patches for kernel 5.10
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2021-12-13 23:22:29 +01:00
Martin Schiller
7e35d86ca2 layerscape: add kernel 5.10 as testing version
This patch adds "KERNEL_TESTING_PATCHVER:=5.10" to the Makefile in
layerscape target to allow using Kernel 5.10 for testing.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2021-12-13 23:22:29 +01:00
Martin Schiller
0a9454918d layerscape: remove unneeded KERNEL_ENTRY_POINT definition
As KERNEL_ENTRY_POINT is identical to KERNEL_LOADADDR, drop it.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2021-12-13 23:22:29 +01:00
Rui Salvaterra
66f9ed1684 ramips: switch to kernel 5.10
Tested on mt7621 (Redmi AC2100) and running stable for several months.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Tested-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
2021-12-13 19:36:52 +01:00