Userspace handling is deprecated. MAC address handling will have to wait
as there's no support for variables other than ethaddr currently.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Userspace handling is deprecated.
This is a weird one. It should be using u-boot,env, but the variable
name is unknown. Keep it as is.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Userspace handling is deprecated.
Move the mac address patch to 10_fix_wifi_mac.
This uses an AR9287, which uses a smaller size for its calibration.
The PCI ID is also wrong.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Userspace handling is deprecated.
Move calibration for pcie node out of dtsi. calibration size for ath10k
and ath9k differs.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Userspace handling is deprecated. MAC address stuff needs to remain
handled in userspace as it's encrypted. Maybe an NVMEM driver can be
written in the future...
Signed-off-by: Rosen Penev <rosenp@gmail.com>
These devices use AR9287, which uses 3d8 as the calibration size, not
440 like newer chips do. Add a compatible line to make it clear that
this is the case.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Userspace handling of both calibration and mac addresses is deprecated.
Also fixed calibration size for ath9k. AR9287 uses 3d8 for its size.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Two use AR9287 and one AR9381. Both have different calibration sizes.
Move differences out of wifi node to make it clearer what's what.
qca,no-eeprom needs to stay for 7362sl as there's no nvmem equivalent
for caldata_extract_reverse
Signed-off-by: Rosen Penev <rosenp@gmail.com>
These two devices use different wifi chips and as a result, different
calibration sizes. Move the differences out of dtsi.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
These units use AR9287, which has a calibration size of 3d8.
Also fixed compatible string to the proper one to indicate AR9287.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
These devices use AR9287, which uses 3d8 as the calibration size, not
440 like newer chips do. Add a compatible line to make it clear that
this is the case.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Not all Kirkwood systems have the Marvell MV88E6XXX switches.
Drop those from the generic config and add them as modules
in the systems that have it.
This was inferred by inspecting the upstream DTS files for any
mv88e* strings and adding the mv88e6xxx kmod package to those
that have an upstream device tree with an MV88E6xxx switch
and an OpenWrt image target.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
d22d7db581d5 bpf_skb_utils.h: add missing include to fix build against newer kernel headers
bbd3e0eb1419 host: fix peer routes on a node acting as gateway
b17164751fc7 unet-tool: add support for generating keys from salt + seed passphrase
041e05870c20 unet-tool: add support for dumping pubkey from signed file
b58920d420cb unet-tool: add support for extracting network data from signed bin file
f335f5b40b4e unet-cli: add support for generating key from seed
8b1f1d099352 unet-cli: add support for importing networks from signed data
188ba05eadf2 unet-cli: add missing command line help for import
8f15fc306a40 unet-cli: fix add-ssh-host with seed keys
486bc3b86dc2 pex-msg: enable broadcast for global PEX socket
e4a24cdfbc1c unet-cli: fix defaults on create
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is using mac-base and so a 0 needs to be added.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17274
Signed-off-by: Robert Marko <robimarko@gmail.com>
Images for xrx200 8M flash are either not building due to image
size (TD-W8970, TD-W8980) or building such that the available
free space in the overlayfs is too little to be useful.
To keep images for these devices buildable, move them into a
small flash variant of the xrx200 subtarget. As these devices
are NOR flash only, remove NAND and UBI references from the
kernel config to gain some additional image size reduction.
The apparent 8M flash devices Arcadyan VGV7510KW22-brn,
Arcadyan VGV7519-brn and Lantiq Easy80920-nor seem to exist in
order to create special "factory" installation images for these
devices (which actually have larger flash: 16MB for the
Arcardyan devices; 64MB for the Lantiq device). As a
considerable amount of surgery would appear to be required to
the uboot-lantiq package structure to separate the "factory"
from the "sysupgrade" device recipes for these devices they
remain in the xrx200 target - if factory images aren't now
created, 23.05.x factory images should suffice for initial
installation.
Tested on: Netgear DM200, TP-Link TD-W8980,
AVM Fritz7490 (xrx200 subtarget: image build only)
Fixes: https://github.com/openwrt/openwrt/issues/16761
Signed-off-by: Andrew MacIntyre <andymac@pcug.org.au>
Link: https://github.com/openwrt/openwrt/pull/17113
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This fixes "sh: write error: Invalid argument" for all default!=1 LEDs
as an empty $brightness was used.
Setting up LEDs via luci also now works again.
Fixes cbdfd03e: "base-files: add option to set LED brightness"
Signed-off-by: Andre Heider <a.heider@gmail.com>
Link: https://github.com/openwrt/openwrt/issues/17269
Signed-off-by: John Crispin <john@phrozen.org>
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.65
Update to checksum only/no patches required a rebase.
Per the changelog, this is a trivial upstream bump with only 4
commits, 2 of which being reverts.
Build system: x86/64
Build-tested: x86/64/AMD Cezanne
Run-tested: x86/64/AMD Cezanne
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/17217
Signed-off-by: Robert Marko <robimarko@gmail.com>
The PHY can handle turning off the GPIOs when turning off all USB ports.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17192
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
- Device: ASUS 4g-AX56
- SoC: MT7621AT
- Flash: 128MB
- RAM: 512MB
- Switch: 1 WAN, 4 LAN (10/100/1000 Mbps)
- WiFi: MT7905 2x2 2.4G + MT7975 2x2 5G
- LTE : Fibocom FG621-EA
- LEDs: 1x POWER (white, configurable)
1x 2.4G (white, not configurable)
1x 5G (white, not configurable)
1x WAN (white, not configurable)
1x 3G/4G (white, not configurable)
3x signal (white, not configurable)
Flash by U-Boot TFTP method:
- Configure your PC with IP 192.168.0.2
- Set up TFTP server and put the factory.bin image on your PC
- Connect serial port(rate:115200) and turn on AP, then interrupt "U-Boot Boot Menu" by hitting any key
Select "2. Upgrade firmware"
Press enter when show "Run firmware after upgrading? (Y/n):"
Select 0 for TFTP method
Input U-Boot's IP address: 192.168.0.1
Input TFTP server's IP address: 192.168.0.2
Input IP netmask: 255.255.255.0
Input file name: openwrt-ramips-mt7621-asus_4g-ax56-squashfs-factory.bin
- Restart AP aftre see the log "Firmware upgrade completed!"
Notice:
- LTE module is disable after flash openwrt image so you must active LTE by following two AT command
echo -e "AT+GTAUTOCONNECT=1\r\n" > /dev/ttyUSB0
echo -e "AT+GTRNDIS=1,1\r\n" > /dev/ttyUSB0
- After finish AT command once, you don't need to input command later even if reboot/restore default
Signed-off-by: Chuncheng Chen <ccchen1984@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16752
Signed-off-by: John Crispin <john@phrozen.org>
Hardware
* Mediatek MT7620A + Mediatek MT7610EN
* 64MB RAM
* 8MB NAND (Winbond 25064FVSIG )
Both 2.4GHZ and 5GHZ are working, it is enabled by default since there is no
physical ethernet port in the device.
All LED's and buttons work.
UART: 57600 8N1 3.3V
Installation
Upload the openwrt-ramips-mt7620-trendnet_tha103ac-initramfs-kernel.bin via
the manufacturer firmware upgrade page on the device.
Upon reboot wait +- 3 mins until the green power LED is not flashing anymore
(do not be tempted to switch the device off while the LED is flashing, unless
you are ready for soldering and TTL) and then press the WPS button to enable
the default OpenWrt Wifi AP, the BLUE wifi LED will start flash.
Then install openwrt-ramips-mt7620-trendnet_tha103ac-squashfs-sysupgrade.bin
via OpenWrt.
The integrated power monitoring and relay do not work in OpenWrt as the PL7223
chip source/documentation is unavailable.
Recovery
Mis-configuration can be dealt with using the RESET button to reset to factory,
worst case scenario will require some serious work and soldering, there's pads
on the PCB for both the UART and ETH0, and I soldered and tested that it does
work.
You will have to power the board using the header pins GND & 5V, see the 8-pin
header socket.
Signed-off-by: Die Peter Pan <diepeterpan@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17114
Signed-off-by: John Crispin <john@phrozen.org>
The original ar71xx version of this device used 1002 as mac address for
both ethernet and wireless. The ath79 version inexplicably changes this
to 2, which seems to be done nowhere else in ath79, indicating it's
bogus.
Restore previous ar71xx assignment. 1002 is used as an ethernet
interface with some other devices as well.
Also remove the bogus caldata userspace extraction. The size is bogus
and it's already handled in dts.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17083
Signed-off-by: John Crispin <john@phrozen.org>
NRadio C8-668GL is a Wi-Fi 6 5G cellular router based on MediaTek MT7981B SoC.
- **SoC**: MediaTek MT7981B (2x Cortex-A53, 1.3GHz)
- **RAM**: Nanya NT5AD512M16C4-JR 1GB DDR4
- **Flash**: ESMT FC51L08SFY3A 8GB eMMC
- **Ethernet**:
- 1x 2.5GbE (via GMAC0 and GPY211 PHY, shared with MT7531AE)
- 3x 10/100/1000 Mbps (via MT7531AE, connected to GMAC0)
- 5G Modem: GMAC1 (via GPY211 PHY - RTL8125BG - RM520N-GL)
- **Wi-Fi**: MediaTek MT7976CN (2.4GHz/5GHz, 802.11ax, 2x2 MIMO, AX3000)
- **Buttons**: Reset, WPS
- **LEDs**: Power, 5G, 4G, WiFi
- **SIM Slot**: 1x Nano SIM
- **5G Modem**: Quectel RM520N-GL (Snapdragon™ X62)
- **Power**: 12V/2A DC, 5.5×2.1 connector
The MAC addresses are derived from the `fac_mac` field in the `bdinfo` partition, formatted as `fac_mac = HWMAC`. The allocation is as follows:
| Vendor | OpenWrt Interface | Address | Notes |
|---------|-------------------|---------------|------------------------------------------------|
| LAN | br-lan | Label MAC | Default |
| WAN | lan4 | Label MAC+1 | Only when lan4 is switched to WAN |
| 2.4GHz | phy0-ap0 | Label MAC | |
| 5GHz | phy1-ap0 | Label MAC | (Local Admin bit set) |
| Modem | eth1 | Label MAC+2 | |
1. Log in to the router via `http://192.168.66.1`/.
2. Upgrade the official firmware to dual-system mode.
3. Select **Burn second system** and upload the `sysupgrade.bin` image.
- Download the image from the OpenWrt build system or build it yourself using the OpenWrt buildroot.
4. Wait for 30 seconds and click **Switch system**.
5. The device will reboot and switch to OpenWrt.
Set the U-Boot environment variable `boot_system=0` and reboot:
```bash
fw_setenv boot_system 0
```
Power off the router, hold the **WPS button**, and power it back on.
1. Rename the stock firmware file to **`recovery.bin`**.
2. Set your PC's Ethernet IP to **192.168.1.88** and connect it to the lan1 port on the router.
3. Run a TFTP server and place the `recovery.bin` file in its root directory.
4. Power off the router, press and hold the **Reset button**, and power it back on.
5. Release the Reset button when the TFTP server shows activity.
6. Wait for the router to flash the firmware and reboot automatically.
- By default, `lan4` is part of `br-lan` and uses the label MAC address.
- To query the RM520N-GL module, use the following command:
```bash
cat /dev/ttyUSB2 & printf 'ATI\r\n' > /dev/ttyUSB2
```
Signed-off-by: Yaoguang Bai <0xdeadc0de@badguys.club>
Link: https://github.com/openwrt/openwrt/pull/17093
Signed-off-by: John Crispin <john@phrozen.org>
Upstream uses devm_reset_control_array_get_optional_shared, which does
not use names. reset-names is also not specified in the documentation.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17118
Signed-off-by: John Crispin <john@phrozen.org>
Both generic-ehci.yaml and generic-ohci.yaml state that phy-names is to
only be usb.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17118
Signed-off-by: John Crispin <john@phrozen.org>
This matches the upstream PHY driver, which removed it.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17118
Signed-off-by: John Crispin <john@phrozen.org>
Don't fail wireless interface bringup on empty PSK set. This is a valid
configuration, resulting in a PSK network which can't be connected to.
It does not fail the bringup of the hostapd process.
Keep failing the interface setup in case a password with invalid length
is used.
This is also beneficial when intending to configure a PPSK network. It
allows to create a network where no PPSK is yet set.
Signed-off-by: David Bauer <mail@david-bauer.net>
Link: https://github.com/openwrt/openwrt/pull/17197
Signed-off-by: John Crispin <john@phrozen.org>
refresh the following patch for ath12k
001-wifi-ath12k-add-11d-scan-offload-support-and-handle-country-code-for-WCN7850.patch
Signed-off-by: Georgi Valkov <gvalkov@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17246
Signed-off-by: John Crispin <john@phrozen.org>
