Sync SPI-NAND/ECC controller driver for MT7622, MT7981, MT7986 and MT7988:
* Platform data for MT7981 was actually missing and is now added.
* Add support for Winbond W25N01KV 1Gbit chip.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Since kernel 5.13 this is needed to enable USB ports on all devices in
subtarget. Previously TF-A and COMPHY driver might have set up this PHY,
but not anymore.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tested-by: Robert Marko <robimarko@gmail.com>
This should be a part of kernel major bump. Fortunately it didn't stall
compilation, so no fixes tag.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
**Hardware specification:**
- SoC: MediaTek MT7981B 2x A53
- Flash: ESMT F50L1G41LB 128MB
- RAM: Nanya NT5CC128M16JR-EK 256MB
- Ethernet: 4 x 10/100/1000 Mbps
- Switch: MediaTek MT7531AE
- WiFi: MediaTek MT7976C
- Button: Reset, Mesh
- Power: DC 12V 1A
- UART: 3.3v, 115200n8
| Layout: |
| :-------- |
| <Antenna> |
| VCC |
| GND |
| Tx |
| Rx |
**Flash instructions:**
1. Rename `openwrt-mediatek-filogic-cetron_ct3003-squashfs-factory.bin` to `factory.bin`.
2. Upload the `factory.bin` using the device's Web interface.
3. Click the upgrade button and wait for the process to finish.
4. Access the OpenWrt interface using the same password.
5. Use the 'Restore' function to reset the firmware to its initial state.
**Notes:**
If you plan to recovery the stock firmware in the future, it's advisable
to connect the device via the serial port and enter failsafe mode to
back up all the MTD partitions before proceeding the steps above.
Signed-off-by: Patricia Lee <patricialee320@gmail.com>
Make use of minor sector size (4k) erasure on supported flash chips
to improve spi read/write performance.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
ath79 PCIe interrupt controller has stopped working correctly. This
is because the DT exposing a non-sensical interrupt-map property,
and their drivers relying on the kernel ignoring this property[1].
This patch fixes the PCIe init error:
ath9k 0000:00:00.0: of_irq_parse_pci: failed with rc=-14
Notice:
This is just a workaround, not a fix. PCIe driver and related dts
node need to be rewritten.
[1] https://lore.kernel.org/all/20211201114102.13446-1-maz@kernel.org/
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
All kernel configs are refreshed by
'make kernel_oldconfig CONFIG_TARGET=target' and
'make kernel_oldconfig CONFIG_TARGET=subtarget'.
upstreamed patches:
010-v5.17-spi-ar934x-fix-transfer-and-word-delays.patch
011-v5.17-spi-ar934x-fix-transfer-size.patch
020-v5.18-spi-ath79-Implement-the-spi_mem-interface.patch
030-v5.18-ath79-add-support-for-booting-QCN550x.patch
build and run tested on:
ath79/generic/ar7241
ath79/generic/qca9563
ath79/nand/ar9344
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Some symbols are outdated or missing due to daily kernel bumps. It's
better to re-add them. All configs are automatically refreshed by
'make kernel_oldconfig CONFIG_TARGET=taget' and
'make kernel_oldconfig CONFIG_TARGET=subtarget'
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
This reverts commit 5356462ce5.
Kernel switching to fw_devlink=on as default broke probing some devices.
Revert it until we get a proper fix.
It seemed that mtd OF_POPULATED hack resolved probing issues but
apparently not all of them. We got reports about reading MAC using NVMEM
not working and USB controllers not working.
Ref: #10232Fixes: #13412
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Fix the issue of dts buswidth cannot be applied properly with spi driver.
Fix the name of buswidth to bus-width in dts in order to fit the format
in linux spi kernel[1] so that spi-tx-bus-width & spi-rx-bus-width can be
parsed properly.
[1] Documentation/devicetree/bindings/spi/spi-controller.yaml
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
This adds support for Radxa ROCK Pi E, rockchip rk3328 board.
Specification:
- CPU: Rockchip RK3328 64-bit Quad-core
- RAM: DDR3 256MB ~ 2GB
- Network:
1 x 10/100/1000M Ethernet
1 x 10/100M Ethernet
- Storage:
1 x MicroSD Slot
1 x eMMC Module Slot
- USB Host/OTG:
1 x USB3.0 Type A HOST
1 x USB2.0 HOST (40-pin pin-header)
- Wireless
RTL8723DU/RTL8821CU
- Debug Serial:
1500000 baud at UART2 ( 40-pin pin-header)
- Power Supply:
Type-C 5V
Optionally PoE
Installation:
- Write image to SD Card or EMMC with dd
- Boot ROCK Pi E from the SD Card
Signed-off-by: Jayantajit Gogoi <jayanta.gogoi525@gmail.com>
Add uboot support for Radxa ROCK Pi E, rockchip rk3328 board.
Add pre-built files to fix swig dependencies.
Specification:
- CPU: Rockchip RK3328 64-bit Quad-core
- RAM: DDR3 256MB ~ 2GB
- Network:
1 x 10/100/1000M Ethernet
1 x 10/100M Ethernet
- USB Host:
1 x USB3.0 Type A HOST
1 x USB2.0 OTG (40-pin pin-header)
- Wireless:
RTL8723DU/RTL8821CU
- Power Supply: Type-C 5V
Installation:
- Write image to SD Card or EMMC with dd
- Boot ROCK Pi E from the SD Card
Signed-off-by: Jayantajit Gogoi <jayanta.gogoi525@gmail.com>
The bootcmd limits the kernel to 4 MiB which is
exceeded when using Device/FitImage. Device/FitzImage
reduces the size to around 3 MiB.
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Thomas Bong <thomas.bong@devolo.de>
Renamed the interfaces to match the other devices.
Name the interface connected to the builtin G.hn chip 'ghn'.
This might toggle at runtime while the G.hn chip is in the
bootloader.
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Thomas Bong <thomas.bong@devolo.de>
Changes:
9dc0800 wireless-regdb: Update regulatory rules for Philippines (PH)
111ba89 wireless-regdb: Update regulatory rules for Egypt (EG) from March 2022 guidelines
ae1421f wireless-regdb: Update regulatory info for Türkiye (TR)
20e5b73 wireless-regdb: Update regulatory rules for Australia (AU) for June 2023
991b1ef wireless-regdb: update regulatory database based on preceding changes
Signed-off-by: Yuu Toriyama <PascalCoffeeLake@gmail.com>
When switching from a STA-only configuration to AP+STA on the same phy, the
STA was previously restarted in order to notify hostapd of the new frequency,
which might not match the AP configuration.
Fix the STA restart by querying the operating frequency from within hostapd
when bringing up the AP.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The NMBM-Enabled layout did not use fit image,
it just need default process. So it was been removed in platform.sh.
It will fix sysupgrade error for xiaomi,mi-router-wr30u-112m-nmbm.
Signed-off-by: Hank Moretti <mchank9999@gmail.com>
Remove stale sites from @GNOME alias:
* remove 2 sites that have stale 3 years old content
* remove 2 sites that have dropped GNOME
* convert 2 sites from FTP to HTTP
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
When a dependency is pulled in via conditional depends, and the condition
is already selected earlier in the chain, drop the condition.
This avoids some corner cases that trigger recursive dependencies.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This reverts commit 6c3eff9dd8.
This appears to cause some regressions in generated config.
Will be replaced with a fixed version later
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When a package foo depends on PACKAGE_foo:bar (in order to make build
dependencies conditional), tracking transitive dependencies can fail because
the internal seen flag is checked/set before eliminating the fake conditional
dependency. This can show up as a depends on not properly turned into a
select further down in the dependency chain
Signed-off-by: Felix Fietkau <nbd@nbd.name>
f429bd94f99e system-linux: switch to new ETHTOOL_xLINKSETTINGS API
Fixes AN announcement for speeds beyond 1 GBit/s.
Adds new UCI options for Ethernet devices:
- autoneg: switch on or off auto-negotiation
- pause: if set to 0, do not announce symmetric flow control capability
- asym_pause: if set to 0, do not announce asymmetric flow control
capability.
- rxpause: if set overrides AN and forces RX pause accordingly
- txpause: if set overrides AN and forces TX pause accordingly
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Relocating the device tree is required for being apply to apply
device tree overylay at boot.
Fixes: 34bb33094a ("mediatek: use updated device tree overlay mechanism for BPi-R64")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
