Assign the GPHY LED pins to the Ethernet controller node instead of
using pin hogging (where pins are assigned to the pin controller).
This is the preferred way of assigning pins upstream.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Assign the NAND pins to the NAND controller node instead of using pin
hogging (where pins are assigned to the pin controller).
This is the preferred way of assigning pins upstream.
While here, define all NAND pins (CLE, ALE, read/RD, ready busy/RDY and
CE/CS1). This means that the pinctrl subsystem knows that these pins are
in use and cannot be re-assigned as GPIOs for example.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Define the SPI pins in the corresponding SoCs.dtsi and assign them to
the SPI controller node. All known boards use CS4 and it's likely that
this is hardcoded in bootrom so this doesn't bother with having
per-board SPI pinmux settings.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Assign the MDIO pins to the switch node instead of using pin hogging
(where pins are assigned to the pin controller).
This is the preferred way of assigning pins upstream.
This converts amazonse, ar9 and vr9. danube is skipped because the pin
controller doesn't define a pinmux for the MDIO pins (some of the SoC
pads may be hardwired to the MDIO pins instead of being configurable).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
The "/dts-v1/;" identifier is supposed to be put once at the beginning
of a device tree file. Thus, it makes no sense to provide it a second
time in to-be-included DTSI files.
This removes the identifier from all DTSI files in /target/linux.
Most of the DTS files in OpenWrt do contain the "/dts-v1/;". It is
missing for most of the following targets, though:
mvebu, ipq806x, mpc85xx, ipq40xx
This does not touch ipq806x for now, as the bump to 4.19 is close.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The led wireless trigger is already set correctly to phy0tpt through the
alias in the device tree.
Signed-off-by: Manuel Kock <github.web@manu.li>
[rephrased commit title]
Signed-off-by: David Bauer <mail@david-bauer.net>
In lantiq, ath9k caldata extraction is implemented to work in two
alternate "modes", the standard one and another one with swapped
byte pairs.
This rearranges the functions so "standard" use is based on the
caldata.sh library, while only a single local function is required
for the special case.
Note that while the parameter for switching between normal and swab
is removed, the size of the caldata is added to the function calls
to stay consistent.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Commit 7519a36774 ("base-files,procd: add generic service status")
introduced the generic 'status' command which broke the previous
dsl_control status output. To fix this, let's rename the "old" command
to "dslstat".
Fixes: 7519a36774 ("base-files,procd: add generic service status")
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
While all ath10k eeproms have a checksum field, so far two
functions for patching ath10k MAC address have been present (and
been used).
This merges code to provide a single function ath10k_patch_mac
in caldata.sh, having its name in accordance with ath9k functions.
By doing so, correct MAC patching for current and future ath10k
devices should be ensured.
This patch adds checksum adjustments for several targets on
ath79 and lantiq.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This unifies MAC address patch functions and moves them to a
common script. While those were implemented differently for
different targets, they all seem to do the same. The number of
different variants is significantly reduced by this patch.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This moves the almost identical calibration data extraction
functions present multiple times in several targets to a single
library file /lib/functions/caldata.sh.
Functions are renamed with more generic names to merge different
variants that only differ in their names.
Most of the targets used find_mtd_chardev, while some used
find_mtd_part inside the extraction code. To merge them, the more
abundant version with find_mtd_chardev is used in the common code.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[rebase on latest master; add mpc85xx]
Signed-off-by: David Bauer <mail@david-bauer.net>
The xor() function is defined in each of the caldata extraction
scripts for several targets. Move it to functions.sh to reduce
duplicate code.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
If chksum_offset is converted by $(($...)) at the beginning, the
check [ -n "$chksum_offset" ] will always return true, as the
conversion yields "0" for an empty argument, and [ -n "0" ] is
true.
With this patch, the variable is not converted before the check,
but only when it's used in dd.
No conversion is done for use in hexdump, as this can deal with
hex value offsets.
Fixes: b133e466b0 ("treewide: convert WiFi caldata size and offset to hexadecimal")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This replaces deprecated backticks by more versatile $(...) syntax.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[decapitalized patch subject at submitter's request]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
BT Openreach ECI VDSL Modem V-2FUb/I is an alias of Alpha ASL56026 as
also stated in the original commit message adding the device
(commit 6254a2028c "lantiq: add support for the Alpha ASL56026").
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This sorts the device definitions in image/Makefile alphabetically
for each subtarget/block.
The order of blocks has not been touched.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT
Uses DEVICE_ALT* variables for alternative vendor/retailer names.
Signed-off-by: Moritz Warning <moritzwarning@web.de>
This commit unifies the LED mapping of the AVM Fritz!Box routers, which
have a combined Power/DSL LED.
With the stock firmware, the Power LED has the following
characteristics:
- Blink when DSL sync is being established
- Solid when DSL sync is present
We can't completely resemble this behavior in OpenWrt. Currently, the
Power LED is completely off, when DSL sync is missing. This is not
really helpful, as a user might have the impression, that he bricked his
device.
Instead, map the Info-LED to the state of the DSL connection.
There is no consistent behavior for the Info-LED in the stock
firmware, as the user can set it's function by himself. The DSL
connection state is one possible option for the Info LED there.
Also use the red Power LED to indicate a running upgrade, in case the
board has a two-color Power LED.
Signed-off-by: David Bauer <mail@david-bauer.net>
This changes size and offset set for WiFi caldata extraction and
MAC address adjustment to hexadecimal notation.
This will be much clearer for the reader when numbers are big, and
will also match the style used for mtd-cal-data in DTS files.
Since dd cannot deal with hexadecimal notation, one has to convert
back to decimal by simple $(($hexnum)).
Acked-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This changes the offsets for the MAC address location in
mtd_get_mac_binary* and mtd_get_mac_text to hexadecimal notation.
This will be much clearer for the reader when numbers are big, and
will also match the style used for mtd-mac-address in DTS files.
(e.g. 0x1006 and 0x5006 are much more useful than 4102 and 20486)
Acked-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The AVM Fritz!Box 7412 does not use the VMMC part of the Lantiq chip but
rather a proprietary solution based on the DECT chip for the FXS ports.
Therefore, the second VPE can be enabled for use with OpenWrt.
Signed-off-by: David Bauer <mail@david-bauer.net>
The AVM FRITZ!Box 7412 buttons are both active low, which is currently
incorrectly defined in the device-tree.
This leads to the device booting directly into failsafe.
Signed-off-by: David Bauer <mail@david-bauer.net>
This commit selects wpad-basic for the FRITZ!Box 7312 and 7412 as
wpad-mini is only selected on boards with small flash.
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
[add short description]
Signed-off-by: David Bauer <mail@david-bauer.net>
The following warnings are introduced by our own patches:
lantiq_etop.c:173:1: warning: no semicolon at end of struct or union
};
^
lantiq_etop.c: In function 'ltq_etop_change_mtu':
lantiq_etop.c:725:2: warning: ISO C90 forbids mixed declarations and code [-Wdeclaration-after-statement]
int max = ETH_HLEN + VLAN_HLEN + new_mtu + ETH_FCS_LEN;
^~~
Signed-off-by: Mathias Kresin <dev@kresin.me>
In DTS Checklist[1] we're now demanding proper generic node names, as
the name of a node should reflect the function of the device and use
generic name for that[2]. Everybody seems to be copy&pasting from DTS
files available in the repository today, so let's unify that naming
there as well and provide proper examples.
1. https://openwrt.org/submitting-patches#dts_checklist
2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[split out treewide patch, integrated P2812HNUF1 rename patch]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[merged key and led changes, use generic node name for flash, wifi and
gpio]
Signed-off-by: Mathias Kresin <dev@kresin.me>
It is pretty ovbious a misuse of the simple-bus binding as no child has
a address.
Luckly the clock node isn't used at all so it is safe to get rid of it.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Set a unit address matching the reg property for the EASY98000 ethernet
node.
Fixes a unit mismatch devicetree compiler warning.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The localbus childs are highly board specific and need to be part of the
board dts. Otherwise we run into duplicate unit address issues if a
board has something else (NAND) connected to the bus id.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The register address is the same for danube und vr9. The register size
is 0x400 byte for danube and 0x300 byte for vr9.
The change doesn't have an impact as the vmmc driver doesn't use the
devicetree and has hardcoded register offsets.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Fixes the following devicetree compiler warning:
unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add size and address cells where missing to fix the following devicetree
compiler warning:
Warning (avoid_default_addr_size): Relying on default #address-cells value
Warning (avoid_default_addr_size): Relying on default #size-cells value
Signed-off-by: Mathias Kresin <dev@kresin.me>
The cpu temperature driver has the register offset hardcode and doesn't
need a reg.
The mdio bus node is only used as a well known name and doesn't need a
reg or unit address.
syscon-reboot doesn't have a unit address or a reg either. The unit name
collides with reset-controller@10 anyway.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add the reg property if the node has an unit address. Fixes the
following device tree compiler warning:
Warning (unit_address_vs_reg): node has a unit name, but no reg property
Signed-off-by: Mathias Kresin <dev@kresin.me>
The current state of the kernel 4.14 support is in the openwrt-19.07
branch. No need to keep a not default used kernel in this branch.
Signed-off-by: Mathias Kresin <dev@kresin.me>
With kernel 4.19 the DMA API relies on a struct device to work properly.
Backport upstream patches which passed a struct device instead of NULL
to the DMA API.
Fixes kernel panics during boot.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
In case a PCI device is physical present, the Lantiq PCI driver need to
be loaded prior to the Lantiq PCIe driver. Otherwise none of them will
work because updating the BAR 0 of a device attached to the PCIe Bus
will fail.
Till kernel commit 9667bb039bf6 ("MIPS: lantiq: remove unnecessary
of_platform_default_populate call"), the Lantiq PCI driver was probed
early in the boot process via plat_of_setup().
Since the mentioned commit, both drivers are probed via
of_platform_default_populate_init() and they are probed according to
their order in the devicetree source file.
If the Lantiq PCI driver is enabled in the devicetree, defer the probing
og the Lantiq PCIe driver till the Lantiq PCI driver is probed. Use the
presence of a PCU bus as indicater for a loaded Lantiq PCI driver.
This way we don't need to shuffle the PCI/PCIe nodes in the devicetree
source file, as they are already (correctly) ordered based on the unit
address.
Signed-off-by: Mathias Kresin <dev@kresin.me>
With kernel 4.19 dwc2 would not want to initialize due to reset
timeouts, while it worked fine with 4.14.
Increase the reset timeouts to 1 second, as it was used by the old
lantiq ifxhcd usb driver.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
The following patches are dropped because they are now upstreamed:
- 0002-gpio-stp-xway-Implement-get-callback.patch
upstreamed with commit 5b9b2b5284f819 ("gpio: stp-xway: Implement get
callback")
- 0027-01-net-phy-intel-xway-add-VR9-version-number.patch
upstreamed with commit 5b73d9955fb4b0 ("net: phy: intel-xway: add VR9
version number")
- 0027-02-net-phy-intel-xway-add-VR9-v1.1-phy-ids.patch
upstreamed with commit f452518c982e57 ("net: phy: intel-xway: add VR9
v1.1 phy ids")
The following patches were updated:
- 0018-MTD-nand-lots-of-xrx200-fixes.patch
the mainline driver now resides in drivers/mtd/nand/raw/xway_nand.c
(instead of drivers/mtd/nand/xway_nand.c)
- 0025-NET-MIPS-lantiq-adds-xrx200-net.patch
the DMA API now requires a valid device to be passed to all operations
- 0028-NET-lantiq-various-etop-fixes.patch
the DMA API now requires a valid device to be passed to all operations
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
This just copies the files from the kernel 4.14 specific folders into
the kernel 4.19 specific folder, no changes are done to the files in
this commit.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
While moving common used parts to dtsi files, the was disabled by
default but not enabled for all boards using the STP.
Fixes: f519fea4c6 ("lantiq: kernel 4.14: cleanup dts files")
Reported-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
The restart button is currently assigned to KEY_POWER power script but
an easily accessible button immediately powering off the device is
undesirable. Switch to using new KEY_POWER2 reboot script with 5 second
seen delay.
Fixes: FS#1965
Signed-off-by: Alan Swanson <reiver@improbability.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [long line wrap]
Commit eae6cac6a3 ("lantiq: add support for AVM FRITZ!Box 7362 SL"), but
one needs an initramfs image to flash OpenWrt from stock firmware (as
described in the commit log). This patch has the initramfs image built
by default.
Thanks to blogic (for pointing to the FEATURES declaration in the target
Makefiles) and Musashino on the forum for suggesting
config/Config-images.in needed editing too. While at it, reorder the
TARGET_INITRAMFS_COMPRESSION_LZMA declarations alphabetically.
This patch will result in initramfs images for all lantiq subtargets
that have the ramdisk flag set. I tested on the falcon and ase
subtargets, which lack that flag, to confirm they don't produce any
initramfs images with this patch - which they do not.
Given the limited scope of the lantiq (sub)target(s), blogic indicated
this should be OK.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[fixed the wrong reference to eae6cac6a3 commit]
This patch fixes disfunctional WLAN LED on TP-Link W8970. The LED was
reported working in the CC release[1], but doesn't work anymore in 18.06.2.
1. 420cb24d41
Tested-by: Damian Janarek <dzanar18@o2.pl>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
AVM devices based on Qualcomm IPQ40xx do not store sector health
information in the OOB area. Make this check optional to support this
platform.
Signed-off-by: David Bauer <mail@david-bauer.net>
This patch re-enables the reset_ppe() functionality for VR9 targets by using
the new lantiq rcu subsystem. The reset sequence in the reset_ppe() function
was taken from the ppa datapath driver of lantiq UGW 7.4.1.
Additionally it adds the required reset definitions to the vr9 dtsi file.
It also prepares the reset_ppe() function calls for the other lantiq targets.
This feature is needed to be able to switch between ltq-atm/ltq-ptm driver
in ATM/PTM Auto-Mode at runtime.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Hardware:
- SoC: Lantiq VRX288
- RAM: Winbond W971GG6JB 1 Gb (128 MiB)
- Flash:
- SPI: 8 Mb (1 MiB) for bootloader and tffs
- NAND: 1 Gb (128 MiB) for OS
- xDSL: Lantiq VRX208
- WLAN: Atheros AR9381
- DECT: Dialog Semiconductors SC14441
Everything except FXS/DECT works
(no drivers for AVM's FXS implementation with SC14441).
Installation via FTP:
1. Use scripts/flashing/eva_ramboot.py to send initramfs-kernel.bin
to the device when powering on.
Standard AVM procedures with finding the correct IP address and
the right moment to open FTP apply here (approx. 4 seconds on 7362SL).
IMPORTANT: set lzma compression in ramdisk options, bootloader stalls
when receiving uncompressed images.
2. Transfer sysupgrade.bin image with scp to /tmp directory
and run sysupgrade
3. First boot might take a bit longer if linux_fs_start was set to 1,
in that case the device will reboot twice, first time it will fail to load
second kernel (overwritten by ubifs), set linux_fs_start to 0 and reboot.
OpenWrt uses the entire NAND flash. Kernel uses 4 MiB and rootfs uses
the rest of 124 MiB, overwriting everything related to FRITZ!OS - both
OS images, config and answering machine/media server data.
To return to FRITZ!OS, use AVM's recovery image.
Signed-off-by: Danijel Tudek <danijel.tudek@gmail.com>
Hardware:
SoC: Lantiq VRX 220
CPU Cores: 2x MIPS 34Kc at 500 MHz
RAM: 128 MiB 250 MHz
Storage: 128 MiB NAND flash
Ethernet: built-in Fast Ethernet switch, only port 2 is used
Wireless: Atheros AR9287-BL1A b/g/n with 2 pcb antennas
Modem: built-in A/VDSL2 modem
DECT: Dialog SC14441
LEDs: 1 two-color, 4 one-color
Buttons: 2
FXS: 1 port via TAE or RJ12 connector
Everything except FXS/DECT works
(no drivers for AVM's FXS implementation with SC14441).
Installation:
Use the eva_ramboot.py script to load an initramfs image on the
device. Run it a few seconds after turning the device on.
$ scripts/flashing eva_ramboot 192.168.178.1 bin/targets/lantiq/xrx200/openwrt-lantiq-xrx200-avm_fritz7412-initramfs-kernel.bin
If it fails to find the device try the ip address 169.254.120.1.
(Firmware updates or the recovery tool apparently change it.)
IMPORTANT: set lzma compression in ramdisk options, bootloader stalls
when receiving uncompressed images.
The device will load it in ram and boot it. You can reach it under
the openwrt default ip address 192.168.1.1.
Check if the key linux_fs_start is not set to 1 in tffs:
$ fritz_tffs_nand -d /dev/mtd1 -n linux_fs_start
If it is set to 1, the bootloader will select the wrong set of
partitions. Restart the box and install an FritzOS upgrade or do a
recovery. Afterwards start again at step 1.
Run sysupgrade to persistently install OpenWRT.
Signed-off-by: Valentin Spreckels <Valentin.Spreckels@Informatik.Uni-Oldenburg.de>
Signed-off-by: Andy Binder <AndyBinder@gmx.de>
The current snapshot release kernel with it's 2119245 Byte
size is too big to fit into the 2097152 (2MiB) area that
was set aside for the kernel. Which causes the device to
fail to boot (after an update or even during a fresh install)
NAND read: device 0 offset 0x60000, size 0x200000
2097152 bytes read: OK
## Booting kernel from Legacy Image at 80800000 ...
Image Name: MIPS OpenWrt Linux-4.14.98
Created: 2019-02-13 9:37:36 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 2119245 Bytes = 2 MiB
Load Address: 80002000
Entry Point: 80002000
Verifying Checksum ... Bad Data CRC
ERROR: can't get kernel image!
This patch fixes the problem by enlarging the kernel partition
at the cost of the ubi/data partition behind it. The patch
also adds a KERNEL_SIZE variable to the image Makefile to
prevent silent corruptions from happening in the future.
Please note: The u-boot environment for the router also
needs to be updated. So please attach an appropriate
serial converter cable and enter the following commands
into the u-boot prompt:
setenv nboot 'nand read 0x80800000 0x60000 0x300000; bootm 0x80800000'
saveenv
The wiki has been updated accordingly:
<https://openwrt.org/toh/zyxel/p2812hnu-f1>
Fixes: FS#2124
Suggested-by: Mafketel (User on bugs.openwrt.org)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
In the upstream netdev led trigger the one mode file was replaced by 3
files named rx, tx and link. Fix the netdev trigger configuration code
to use the modified API.
This fix is based on 201058b35c ("base-files: Fix netdev led trigger")
Fixes: aa3b6a08c5 ("kernel: Replace ledtrig-netdev with upstream backport")
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Enable support for 2nd USB port, which is available on Fritz!Box 7320
and 7330. It was run-tested on 7320 and 7330 as well.
Signed-off-by: Robert Resch <openwrt@webnmail.de>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This commit changes the model string and device title of all AVM boards
to fit the naming of the manufacturer.
Drop all provider-specific titles as they are re-used for every device
generation by 1&1. The original AVM model name is printed on the bottom
of every devices.
Exception applies for boards which are only supported by a specific
sub-revision.
Signed-off-by: David Bauer <mail@david-bauer.net>
>From the Documentation/devicetree/bindings/leds/common.txt:
- default-state : The initial state of the LED. Valid values are "on", "off",
and "keep". If the LED is already on or off and the default-state property is
set the to same value, then no glitch should be produced where the LED
momentarily turns off (or on). The "keep" setting will keep the LED at
whatever its current state is, without producing a glitch. The default is
off if this property is not present.
So setting the default-state of the LEDs to `off` is redundant as `off`
is default LED state anyway. We should remove it as almost every new
PR/patch submission contains this property by default which seems to be
just copy&paste from some DTS file already present in the tree.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The current stats always have a 'ms' suffix, and they're used by luci.
Introduce dsl.latency_[down|up] values, exported in µs without suffix.
Signed-off-by: Andre Heider <a.heider@gmail.com>
I wanted to add status LEDs support to my imx6 based board and have found out,
that I could use diag.sh script found in ramips platform, which seems to be
also shared in a few other platforms:
4801276bc2078c5bcf03003c831e3b0a target/linux/ramips/base-files/etc/diag.sh
4801276bc2078c5bcf03003c831e3b0a target/linux/ipq40xx/base-files/etc/diag.sh
4801276bc2078c5bcf03003c831e3b0a target/linux/ath79/base-files/etc/diag.sh
And @chunkeey suggested to me, that I can also add lantiq, ipq806x and
apm821xx to the list of platforms which could share this generic
diag.sh.
I've extended the base diag.sh in a way, that if it detects any of the
DTS LED aliases, then it would use the generic DTS set_led_state code.
The code in platform's diag.sh has moved to base-files package in this
commit:
base-files: diag.sh: Make it more generic towards DTS so it could be reused
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Tested-by: Christian Lamparter <chunkeey@gmail.com> (apm821xx and ipq40xx)
Add out of the box support for 802.11r and 802.11w to all targets not
suffering from small flash.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Mathias did all the heavy lifting on this, but I'm the one who should
get shouted at for committing.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
We select ath10k-ct by default, but it is still possible to build
the upstream version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John Crispin <john@phrozen.org>
- fix single spaces hidden by a tab
- replace indentation with spaces by tabs
- make empty lines empty
- drop trailing whitespace
- drop unnecessary blank lines
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Indicate a (sys)upgrade via leds as well. It brings the lantiq diag.sh
script en par with the other implementations using devicetree aliases
to define multiple leds for boot status indication.
By default, use the boot finished led to indicate an upgrade for now.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Without this patch you will get an error "gpio-export probe deferral
not supported" when you try to export i2c expander gpio pins.
gpio-export is probed long before i2c-bus and i2c expander are created
and it doesn't retry it so none pins are exported.
Signed-off-by: René van Dorst <opensource@vdorst.com>
apply the change to all instances of the gpio exports patch
Signed-off-by: Mathias Kresin <dev@kresin.me>
The FritzBox 7312 is also known as 1&1 WLAN-MODEM. The device is almost
the same as FB7330, but only one ETH-Port and no USB.
Hardware
SoC: Lantiq Xway ARX188 PSB 50812 EL
RAM: 64MB DDR1 (Zentel A4S12D40FTP-G5)
Ethernet: Atheros 8030
Wireless: Atheros AR9227 b/g/n 2x2
DSL: Lantiq ADSL2+
DECT: Dialog SC14441
Buttons: WiFi, DECT
LEDs: Power/DSL, Fon, DECT, WLAN, Info
LEDs
Power: GPIO#44 (active low)
Internet: GPIO#47 (active low)
DECT: GPIO#38 (active low)
WLAN: GPIO#37 (active low)
Info: GPIO#35 (active low)
The Fon LED is labeled as internet in avm gpl sources.
Buttons
WLAN: GPIO#1 (active low)
DECT: GPIO#2 (active low)
Phy
GPIO#03: 25 MHz
GPIO#34: Reset (active low)
GPIO#39: Int
GPIO#42: MII MDIO
GPIO#43: MII MDC
PCIe
GPIO#21: reset (active low)
Installation:
To install OpenWrt via Eva bootloader, within the first seconds after
power on a ftp connection need to be established to the FRITZ!Box at
192.168.178.1 and the the following ftp commands need to be run:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put /path/to/openwrt-lantiq-xway-avm_fritz7312-squashfs-sysupgrade.bin mtd1
ftp> quote REBOOT
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
Use of_mdiobus_register() to pass the ethernet phy node to the phy
drivers. This is needed for the at8030 phy driver which needs to know
the GPIO which is connected to the ar8030 reset pin.
This driver expects a child in gsw/etop node named "mdio-bus", which has
the ethernet phys defined:
&gsw {
phy-mode = "rmii";
phy-handle = <&phy0>;
mtd-mac-address = <&ath9k_cal 0xa91>;
mtd-mac-address-increment = <(-2)>;
mdio-bus {
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;
phy0: ethernet-phy@0 {
reg = <0>;
reset-gpios = <&gpio 34 GPIO_ACTIVE_LOW>;
};
};
};
Fallback to mdiobus_register() if no mdio-bus child node exists. This
way we don't need to touch all xway dts files, for which we don't know
the actual address on the mdio bus.
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
Add a new config option to allow to select the default compile
optimization level for the kernel.
Select the optimization for size by default if the small_flash feature is
set. Otherwise "Optimize for performance" is set.
Add the small_flash feature flag to all (sub)targets which had the
optimization for size in their default kernel config.
Remove CC_OPTIMIZE_FOR_* symbols from all kernel configs to apply the new
setting.
Exceptions to the above are:
- lantiq, where the optimization for size is only required for the
xway_legacy subtarget but was set for the whole target
- mediatek, ramips/mt7620 & ramips/mt76x8 where boards should have
plenty of space and an optimization for size doesn't make much sense
- rb532, which has 128MByte flash
Signed-off-by: Mathias Kresin <dev@kresin.me>
Increase the available flash memory size in AVM Fritz!Box 3370 by
incorporating the unused extra partitions located after the ubi partition.
Note that users upgrading from a previous OpenWRT version need to
re-install from the boot loader to pick up the new partition layout.
Available flash space for rootfs+overlay increases from 48MB to 124MB.
Reverting to the OEM firmware is still possible (via the recovery utility
provided by AVM) as the OEM firmware appears to reformat the config and
nand-filesystem partitions upon first boot if necessary. The
reserved-kernel and reserved-filesystem partitions are overwritten by the
OEM firmware when installing an update, so their contents do not matter.
Boot loader and device-specific information (MAC addresses, calibration
data, etc.) are not located in NAND flash and remain unharmed by this
changed.
Tested with OEM firmware 06.54 on device with HWRevision 5 and Micron
flash chip.
Signed-off-by: Michael Kuron <m.kuron@gmx.de>
To keep the status of a LED connected to the stp during boot, the get
callback is required. If the callback is missing and the LED default
state is set to keep in the devicetree, the gpio led driver errors out
during load.
Fixes: FS#1620
Signed-off-by: Mathias Kresin <dev@kresin.me>
Check if the GPIO is valid (or set at all). If no GPIO is set in the
devicetree, a gpiolib related kernel warning + stacktrace is shown during
boot and gpio-export reports GPIOs as exported albeit none really is.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Both version of the vg3503j have the LAN1 labelled port connected to
switch port 4 and the LAN2 labelled port connected to switch port 2.
Signed-off-by: Mathias Kresin <dev@kresin.me>
When upstream kernel introduced commit c55fa3cccbc2c672e7f118be8f7484e53a8e9e77
we incorrectly updated our hack integration patch that updates atm/common.c
+++ b/net/atm/common.c
@@ -62,10 +62,16 @@ static void vcc_remove_socket(struct soc
write_unlock_irq(&vcc_sklist_lock);
}
+struct sk_buff* (*ifx_atm_alloc_tx)(struct atm_vcc *, unsigned int) = NULL;
+EXPORT_SYMBOL(ifx_atm_alloc_tx);
+
static bool vcc_tx_ready(struct atm_vcc *vcc, unsigned int size)
{
struct sock *sk = sk_atm(vcc);
+ if (ifx_atm_alloc_tx != NULL)
+ return ifx_atm_alloc_tx(vcc, size)
The correct solution is to drop our ifx_atm_alloc_tx replacement hack
entirely and let the kernel do its thing.
In reality neither pppoatm or BR2684 interfaces actually hit this code,
so the incorrect integration would only be noticed with direct socket
calls which we are unaware of a use-case.
This is not the solution to pppoatm vc-mux failing to work which started
the whole investigation, but let's fix it up anyway.
With sincerest thanks to David Woodhouse <dwmw2@infradead.org> &
Mathias Kresin <dev@kresin.me>.
Tested-on: lantiq, BT HomeHub 5a
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Recent Speedport firmware downloads only work over HTTPS, so the user
either needs to provide the already downloaded file or install
ustream-ssl-* as well as ca-certificates or ca-bundle.
So to get VDSL2 with vectoring on xRX200, simply run
vdsl_fw_install.sh
on the target and either provide the downloaded file as instructed or
make sure the device is connected to the Internet and can download that
HTTPS url itself.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
THIN_ARCHIVES option is enabled by default in the kernel configuration
and no one target config disables it. So enable it by default and remove
this symbol from target specific configs to keep them light.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
New FUTEX_PI configuration symbol enabled if FUTEX and RT_MUTEX symbols
are enabled. Both of these symbols are enabled by default in the
generic config, so enable FUTEX_PI by default too to keep platform
specific configs minimal.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
OVERLAY_FS config symbol selects EXPORTFS since 4.12 kernel, we have
OVERLAY_FS enabled by default, so enable EXPORTFS in the generic config
of 4.14 and remove this option from platform specific configs.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
DRM_LIB_RANDOM config symbol selected only by DRM_DEBUG_MM_SELFTEST
which is disable by default, so disable DRM_LIB_RANDOM by default too.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
These options do not used by any supported arch, so disable them by
default to make arch configs a bit more clean.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Only one arch (x86_64) enables this option. So disable
ARCH_WANTS_THP_SWAP by default and remove referencies to it from all
configs (except x86_64) to make them clean.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
It isn't a phy supply, as the phy is still up if the GPIO is low. It
rather is the supply for the vbus. A correct setting/definition will be
relevant as soon as USB peripheral mode is supported.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Rename the image and use a compatible string which indicates that only
hardware revision 2 and higher is supported.
It allows to use the wireless LED, as HWRev 1 uses GPIO#39 for the
wireless LED and starting with HWRev 2 GPIO#35 is used for the wireless
LED and GPIO#39 for IFX_GPIO_MODULE_EXTPHY_MDIO.
The HWREV can be checked by connecting to the fritzbox right after power
on via ftp:
ftp> quote GETENV HWSubRevision
Within the same HW revision 5 of the Fritz!Box 3370 different NAND flash
chips are used. Usually it isn't a big deal but depending on the used
NAND flash chip, the ECC calculation is done different (and incompatible
of course).
Boards with a Micron MT29F1G08ABADA NAND flash chip are using the NAND
chip to calculate the ECC (on-die). Boards with a Hynix HY27UF081G2M NAND
flash chip are doing the ECC calculation in software.
Supporting both with a single DTS isn't possible. It might be possible
to add a patch selecting the ECC mode dynamicaly based on the found NAND
flash chip. But such a patch has no chance to get accepted upstream and
most likely need to be touched with every kernel update.
Instead two images are created. One for Micron NAND flash chip and one
for Hynix NAND flash chip. So far no pattern is known to identify the
used flash chip without opening the box.
Add the power off GPIO. At least EVA version 2186 sets/keeps the GPIO as
input, which will cause a reboot 30sec after power on. For boards with
EVA version 2186 the installation is tricky as it has to be finished
within the 30sec time frame.
The EVA version can be checked by connecting to the fritzbox right after
power on via ftp:
ftp> quote GETENV urlader-version
The ath9k eeprom/caldata is at a different and offset and stored in
reverse order (from the last byte to the beginning) on the flash.
Reverse the bits to bring the data into the format expected by the
ath9k driver.
Since the ath9k eeprom is stored in reverse order on flash, we can not
use the mac address from the on flash eeprom. Get the MAC address from
the tffs instead.
Within the same HW revision 5 of the Fritz!Box 3370 both version of the
vr9 SoC are used. During preparation of kernel 4.14 support, all
devicetree source files were changed to load the vr9 v1.1 and vr9 v1.2
gphy firmware, which fixed the embedded phys for boards using the
version 1.2 of the vr9 SoC.
While at it, add a trigger to make use of the LAN LED. Setup the
build-in switch and add a hint for LuCI two show the ports in order
matching the labels on the case
Add support for the second USB port and provide the volatage GPIOs. Use
GPIO#21 as PCIe reset pin. The lan led is connected to GPIO#38.
Name the rootfs partition ubi and remove the mtd/rootfs related kernel
bootargs to use the OpenWrt autoprobing based on the partition name.
Enable sysupgrade support to allow an upgrade from a running system.
Since sysupgrade wasn't supported till now, drop image build code which
was added to allow a sysupgrade from earlier OpenWrt versions.
Build images that allow an (initial) installation via EVA bootloader.
To install OpenWrt via Eva bootloader, within the first seconds after
power on a ftp connection need to be established to the FRITZ!Box at
192.168.178.1 and the the following ftp commands need to be run:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote SETENV linux_fs_start 0
ftp> quote MEDIA FLSH
ftp> put /path/to/openwrt-lantiq-xrx200-FRITZ3370-eva-kernel.bin mtd1
ftp> put /path/to/openwrt-lantiq-xrx200-FRITZ3370-eva-filesystem.bin mtd0
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Backport patch accepted upstream which removes the reset asserts of the
xrx200 gphy driver on reboot/remove.
While doing a global software reset, these bits are not cleared and let
some bootloader fail to initialise the GPHYs. The bootloader don't expect
these bits to be set, as they aren't during power on.
The asserts were a workaround for a wrong syscon-reboot mask. With a mask
set which includes the GPHY resets of the first reset register, the
resets of the second reset register arn't required any more.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Merge the two existing functions and use a parameter for the type
header field.
It updates the syntax of the former mpc85xx fake ramdisk header
command to be compatible with mkimage from u-boot 2018.03 and fixes the
build error spotted by the build bot.
Signed-off-by: Mathias Kresin <dev@kresin.me>
We need to reset the GPHYs on reboot as well. Otherwise the bootloader
might have issues to reset/find the GPHYs.
Signed-off-by: Mathias Kresin <dev@kresin.me>
During upstreaming the intel phy driver, support for the vr9 v1.1
embedded phys got lost. Backport the upstream send patch adding support
for the vr9 v1.1 embbeded phys to the driver.
Signed-off-by: Mathias Kresin <dev@kresin.me>
cosmetic fixes
Signed-off-by: Mathias Kresin <dev@kresin.me>
The latest bootloader versions load the firmware into memory and call
`chk_dniimg` (defined in Netgear GPL release), which expects to find
three consecutive block-aligned uImages. Add two fake uImage headers
after the kernel to fool this check.
This wastes up to 128k of space for alignment. The alternative would be
to put the rootfs in a second uImage, but this would limit the firmware
size to 0x710000 (the number of bytes loaded and verified by the
bootloader) instead of 0x7b0000 (the size of the firmware partition).
Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
This makes some of the mtd patches apply again after some generic
patches were changed.
These problems where found by build bot.
Fixes: ac9bcefa3b ("kernel: use V10 of mtd patchset adding support for "compatible" string")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Lantiq XRX200 aka VR9 doesn't have an asc0. Instead,
there is an USIF module which can either be an UART or a
SPI Controller.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Updated the devicetree source files to make use of the following
upstreamed drivers:
- xrx200 ethernet phy
- reset controller unit
- dwc2
- fpi
Use our custom xrx200 ethernet phy compatible to support boards, which
have switched the vr9 revision during lifetime, with a single devicetree
source file.
By switching to the dwc2 driver + usb phy framework, we don't need to used
our custom gpio power patch and can use a fixed regulator instead.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Mathias Kresin <dev@kresin.me>
On danube the USB0 registers are at 1e101000 similar to all other lantiq
SoCs.
On Danube and AR9 the USB core is connected to the AHB bus, hence we need
to enable the AHB Bus as well.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add a custom xrx200 ethernet phy compatible to load the firmware matching
the vr9 revision without specifing an expected revision.
We have quite a few boards in the tree were later produced ones are using
a more recent vr9. It is impossible to distinguish which revision of the
vr9 is used without opening the case and removing a heatsink for some of
them.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This reverts kernel commit 1eed40043579 ("MIPS: smp-mt: Use CPU interrupt
controller IPI IRQ domain support"). With the patch applied, the kernel
hangs during boot if SMP is active.
The Lantiq IRQ controller gets registered first and it directly handles
the MIPS native SW1/2 and HW0 - HW5 IRQs. It looks like this controller
already registers IRQ 0 - 7 and the generic driver only gets the following
IRQs starting later.
The upstream discussion can be found at
https://www.linux-mips.org/archives/linux-mips/2017-05/msg00059.html.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This just copies the patches, configuration and dts files into the
directories hich are used for kernel 4.14.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Move the devicetree source files to a kernel specific directory in
preparation of adding kernel 4.14 support.
Rename the subtarget kernel config files to match a specific kernel
version.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Rename the gphy firmware to match the name requested by kernel 4.14 and
update the devicetree source files to use the new name.
Update the u-boot lantiq Makefile to be compatible with the new names as
well.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Calling nand_do_upgrade() from platform_pre_upgrade() was deprecated
with 30f61a34b4 ("base-files: always use staged sysupgrade").
Update the platform upgrade code to use platform_do_upgrade() for NAND
images as well.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The watchdog kill command was meant for busybox watchdog. Busybox watchdog
was replaced by the procd watchdog mid 2013 with commit df7ce9301a
("busybox: disable the watchdog utility by default"), which makes the kill
command obsolete since quite some time.
Signed-off-by: Mathias Kresin <dev@kresin.me>
To make it more accessible for nodejs users to configure and run a build
on mips target lacking hardware fpu
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Renaming an atm etherbride using 'ip link' (via hotplug) is racy since the
original netdev might disappear before br2684ctl has finished appling it's
setting:
local2.notice br2684ctl[1667]: Interface "nas0" created sucessfully
local2.notice br2684ctl[1667]: Communicating over ATM 0.8.35, encapsulation: LLC
kern.info kernel: dsl0: renamed from nas0
kern.err kernel: br2684:br2684_regvcc: tried to attach to non-existent device
local2.err br2684ctl[1667]: Could not configure interface:No such device or address
By passing the final used netdev name to br2684ctl_wrap another race
condition workaround will be enabled again.
Change the lantiq ptm driver to create a netdev with the name dsl as well.
Albeit the rename via 'ip link' works fine so far, using a different
approach for ptm then atm could be confusing.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The Annex A and Annex B version are using the same (old) userspace
boardname. Update the SUPPORTED_DEVICES to allow an update from lede-17.01.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This was broken in 7bab49fd ("lantiq: add compatible strings to dts
files"), causing for the dm200 garbled serial output during boot, and
likely other issues.
Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
[fix the compat string of the P2601HNFX as well]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The value DSL_ChipSetHWVersion is fetched from the dsl frontend
via the dsl_control service, but not really provided by the dsl
frontend firmware and for now always "UNKNOWN".
The lantiq support told us that this information wouldn't be
provided in the foreseeable future, so let's remove this
useless "UNKNOWN" information.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Use <manufacturer>_<modelname> as image name.
Use the BOARD_NAME variable to ensure that the former used boardname is
still used as the subdirectory name for the sysupgrade-tar image, to
not break sysupgrade from earlier versions.
While at it, normalise the image filenames by using only lower case
characters and bin as file extension for sysupgrade images.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the first compatible string as board name in userspace. Add the new
board name as well as the former used board name to the image metadata
to keep compatibilty with already deployed installations.
Don't add the former used boardname for boards which exists only in
master or evaluation boards.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Lantiq and IPQ806X (which includes IPQ40XX) both define the
same custom function {ipq806x|lantiq}_get_dt_led.
This patch moves the function into the base-file package at
lib/functions/leds.sh to make it more accessible for other
targets as well.
Cc: Mathias Kresin <dev@kresin.me>
Cc: John Crispin <john@phrozen.org>
Cc: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This will avoid some conflicts when doing a git rebase or merge,
specially when adding support to a new device.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
[drop brcm47xx changes which rename the images]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Remove the WW suffix, everything without a region suffix is world wide
anyway.
While at it, normalise the image filenames by using only lower case
characters.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Users are confused which image type they should use and there are more
drawbacks than adavantages in using a r/w ubifs rootfs in constrast to
a read-only squashfs rootfs like:
- less available free flash space due to better compression of squashfs
images
- no support for factory reset due to r/w filesystem
- possibility to break failsafe due to r/w filesystem
Therefore, drop support for r/w ubifs rootfs images.
Signed-off-by: Mathias Kresin <dev@kresin.me>
