Commit f4fb63d2ab ("ipq40xx: 5.10: move AR40xx to MDIO drivers") moved
the ar40xx driver files to kernel version specific directories to place
them in different subdirectory in kernel tree. But now kernel 5.4 is
gone and there is no reason to keep them separate. Move them back to
common files/ directory.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Also apply commit ab7e53e5cc ("ipq40xx: 5.10: fix ar40xx driver") to
5.15 driver.
The commit fixes the data corruption on TX packets. Packets are
transmitted, but their contents are replaced with zeros. This error is
caused by the lack of guard (50 ms) intervals between calibration phases.
This error is treated by adding mdelay(50) to the calibration function
code. In the original qca-ssda code, these mdelays were existing, but in
the ar41xx.c they are gone.
Fixes: 87318eb179 ("ipq40xx: 5:15: copy config and patch from 5.10")
Signed-off-by: Nick Hainke <vincent@systemli.org>
According wiki https://docs.gl-inet.com/en/2/hardware/mt300n-v2/
GL-MT300N-V2 have I2C interface on GPIO4, GPIO5.
Adding I2C in device tree make possible using I2C on this device.
Signed-off-by: Ptilopsis Leucotis <PtilopsisLeucotis@yandex.com>
Hardware specs:
SoC: Qualcomm IPQ8065 (dual core Cortex-A15)
RAM: 512 MB DDR3
Flash: 256 MB NAND, 32 MB NOR
WiFi: QCA9983 2.4 GHz, QCA9984 5 GHz
Switch: QCA8337
Ethernet: 5x 10/100/1000 Mbit/s
USB: 1x USB 3.0 Type-A
Buttons: WPS, Reset
Power: 12 VDC, 2.5 A
Ethernet ports:
1x WAN: connected to eth2
4x LAN: connected via the switch to eth0 and eth1
(eth0 is disabled in OEM firmware)
MAC addresses (OEM and OpenWrt):
fw_env @ 0x00 d4🆎82:??:??:?a LAN (eth1)
fw_env @ 0x06 d4🆎82:??:??:?b WAN (eth2)
fw_env @ 0x0c d4🆎82:??:??:?c WLAN 2.4 GHz (ath1)
fw_env @ 0x12 d4🆎82:??:??:?d WLAN 5 GHz (ath0)
fw_env @ 0x18 d4🆎82:??:??:?e OEM usage unknown (eth0 in OpenWrt)
OID d4🆎82 is registered to:
ARRIS Group, Inc., 6450 Sequence Drive, San Diego CA 92121, US
More info:
https://openwrt.org/inbox/toh/arris/tr4400_v2
IMPORTANT:
This port requires moving the 'fw_env' partition prior to first boot to
consolidate 70% of the usable space in flash into a contiguous partition.
'fw_env' contains factory-programmed MAC addresses, SSIDs, and passwords.
Its contents must be copied to 'rootfs_1' prior to booting via initramfs.
Note that the stock 'fw_env' partition will be wiped during sysupgrade.
A writable 'stock_fw_env' partition pointing to the old, stock location
is included in the port to help rolling back this change if desired.
Installation:
- Requires serial access and a TFTP server.
- Fully boot stock, press ENTER, type in:
mtd erase /dev/mtd21
dd if=/dev/mtd22 bs=128K count=1 | mtd write - /dev/mtd21
umount /config && ubidetach -m 23 && mtd erase /dev/mtd23
- Reboot and interrupt U-Boot by pressing a key, type in:
set mtdids 'nand0=nand0'
set mtdparts 'mtdparts=nand0:155M@0x6500000(mtd_ubi)'
set bootcmd 'ubi part mtd_ubi && ubi read 0x44000000 kernel && bootm'
env save
- Setup TFTP server serving initramfs image as 'recovery.bin', type in:
set ipaddr 192.168.1.1
set serverip 192.168.1.2
tftpboot recovery.bin && bootm
- Use sysupgrade to install squashfs image.
This port is based on work done by AmadeusGhost <amadeus@jmu.edu.cn>.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
[add 5.15 changes for 0069-arm-boot-add-dts-files.patch]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Add NVRAM quirks script for the bcm53xx target. Split NVRAM quirks for the
bcm47xx and bcm53xx targets. Move clear partialboot NVRAM quirk for Linksys
EA9500 here. Add set wireless LED behaviour quirk for Asus RT-AC88U.
Use boot() instead of start() as nvram commands are meant to be executed
only once, at boot.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
this adds the new dts-binding "mediatek,led_source"
currently for MT7628AN and MT7688 built-in switches,
which is documented as a 3-bit field configuring the
switch LEDs for various control schemes from 0 to 3.
Normally this is not needed, but e.g. for Asus RT-AC1200-V2
it is a must to set it to the anyway undocumented value
of 4, to have the switch LEDs react correctly on link/act
events. This is an MT7628DAN device, but I doubt this is
a speciality of this particular SoC.
Also added the RT305X_ESW_LED_OFF value to LED states.
Did also rename the register RT5350_EWS_REG_LED_POLARITY
to RT5350_EWS_REG_LED_CONTROL, which is the correct name.
Also making use of defines for some hardcoded values.
Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
This patch configures kernel testing version for kirkwood target.
Compile tested: all
Run tested: Endian 4i
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This patch makes only a copy of 5.10 config and patches.
Patches merged in upstream was omited.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Patch that corrects sleep clock frequency has already been backported
to 5.15 stable so remove the duplicate patch.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Add 5.15 kernel as a testing kernel version in the Makefile.
Linksys EA6350v3/EA8300/MR8300 will not build with buildbot settings and
should be disabled when the target is switched, unless the image size is
reduced again.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Robert Marko <robert.marko@sartura.hr>
[add comment for increased kernel size]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Kernel 5.15 have some new api for ethtool and phy.
Add ifdef to fix compilation error.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Robert Marko <robert.marko@sartura.hr>
The 2.4GHz interface doesn't come up properly with the log showing:
mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK)
As seen on other MT7621 boards this is caused by a missing reset GPIO.
The MT7621 dtsi set GPIO 19 as PCIe reset GPIO, which on this board
reset the 5GHz interface on port 0. Add GPIO 8 to the PCIe reset GPIO
list to also reset the 2.4GHz interface on port 1.
Signed-off-by: Alban Bedel <albeu@free.fr>
SoC: Atheros AR7161
RAM: DDR 128 MiB (hynix h5dU5162ETR-E3C)
Flash: SPI-NOR 8 MiB (mx25l6406em2i-12g)
WLAN: 2.4/5 GHz
2.4 GHz: Atheros AR9220
5 GHz: Atheros AR9223
Ethernet: 4x 10/100/1000 Mbps (Atheros AR8021)
LEDs/Keys: 2/2 (Internet + System LED, Mesh button + Reset pin)
UART: RJ45 9600,8N1
Power: 12 VDC, 1.0 A
Installation instruction:
0. Make sure you have latest original firmware (3.7.11.4)
1. Connect to the Serial Port with a Serial Cable RJ45 to DB9/RS232
(9600,8N1)
screen /dev/ttyUSB0 9600,cs8,-parenb,-cstopb,-hupcl,-crtscts,clocal
2. Configure your IP-Address to 192.168.1.42
3. When device boots hit spacebar
3. Configure the device for tftpboot
setenv ipaddr 192.168.1.1
setenv serverip 192.168.1.42
saveenv
4. Reset the device
reset
5. Hit again the spacebar
6. Now load the image via tftp:
tftpboot 0x81000000 INITRAMFS.bin
7. Boot the image:
bootm 0x81000000
8. Copy the squashfs-image to the device.
9. Do a sysupgrade.
https://openwrt.org/toh/netgear/wndap360
The device should be converted from kmod-owl-loader to nvmem-cells in the
future. Nvmem cells were not working. Maybe ATH9K_PCI_NO_EEPROM is missing.
That is why this commit is still using kmod-owl-loader. In the future
the device tree may look like this:
&ath9k0 {
nvmem-cells = <&macaddr_art_120c>, <&cal_art_1000>;
nvmem-cell-names = "mac-address", "calibration";
};
&ath9k1 {
nvmem-cells = <&macaddr_art_520c>, <&cal_art_5000>;
nvmem-cell-names = "mac-address", "calibration";
};
&art {
...
cal_art_1000: cal@1000 {
reg = <0x1000 0xeb8>;
};
cal_art_5000: cal@5000 {
reg = <0x5000 0xeb8>;
};
};
Signed-off-by: Nick Hainke <vincent@systemli.org>
Add USB power control in DTS for GL.iNet models:
- AR300M;
- AR300M-Ext;
- AR300M16;
- AR300M16-Ext.
Signed-off-by: PtilopsisLeucotis <PtilopsisLeucotis@yandex.com>
This commit adds support for the TP-Link Deco M4R (it can also be M4,
TP-Link uses both names) v1 and v2. It is similar hardware-wise to the
Archer C6 v2. Software-wise it is very different. V2 has a bit different
layout from V1 but the chips are the same and the OEM firmware is the same
for both versions.
Specifications:
SoC: QCA9563-AL3A
RAM: Zentel A3R1GE40JBF
Wireless 2.4GHz: QCA9563-AL3A (main SoC)
Wireless 5GHz: QCA9886
Ethernet Switch: QCA8337N-AL3C
Flash: 16 MB SPI NOR
Flashing:
The device's bootloader only accepts images that are signed using
TP-Link's RSA key, therefore this way of flashing is not possible. The
device has a web GUI that should be accessible after setting up the device
using the app (it requires the app to set it up first because the web GUI
asks for the TP-Link account password) but for unknown reasons, the web
GUI also refuses custom images.
There is a debug firmware image that has been shared on the device's
OpenWrt forum thread that has telnet unlocked, which the bootloader will
accept because it is signed. It can be used to transfer an OpenWrt image
file over to the device and then be used with mtd to flash the device.
Pre-requisites:
- Debug firmware.
- A way of transferring the file to the router, you can use an FTP server
as an example.
- Set a static IP of 192.168.0.2/255.255.255.0 on your computer.
- OpenWrt image.
Installation:
- Unplug your router and turn it upside down. Using a long and thin object
like a SIM unlock tool, press and hold the reset button on the router and
replug it. Keep holding it until the LED flashes yellow.
- Open 192.168.0.1. You should see the bootloader recovery's webpage.
Choose the debug firmware that you downloaded and flash it. Wait until the
router reboots (at this stage you can remove the static IP).
- Open a terminal window and connect to the router via telnet (the primary
router should have a 192.168.0.1 IP address, secondary routers are
different).
- Transfer the file over to the router, you can use curl to download it
from the internet (use the insecure flag and make sure your source accepts
insecure downloads) or from an FTP server.
- The router's default mtd partition scheme has kernel and rootfs
separated. We can use dd to split the OpenWrt image file and flash it with
mtd:
dd if=openwrt.bin of=kernel.bin skip=0 count=8192 bs=256
dd if=openwrt.bin of=rootfs.bin skip=8192 bs=256
- Once the images are ready, you have to flash the device using mtd
(make sure to flash the correct partitions or you may be left with a
hard bricked router):
mtd write kernel.bin kernel
mtd write rootfs.bin rootfs
- Flashing is done, reboot the device now.
Signed-off-by: Foica David <superh552@gmail.com>
The Wavlink WL-WN533A8 is an AC3000 router with 5 gigabit ethernet ports
and one USB 3.0 port.
It's also known as Wavlink QUANTUM T8.
Hardware
--------
SoC: Mediatek MT7621A
RAM: 128MB (Nanya NT5CB64M16GP-EK)
FLASH: 16MB NOR (GigaDevice GD25Q127CSIG3)
ETH:
- 5x 10/100/1000 Mbps Ethernet (4x LAN + 1x WAN)
WIFI:
- 1x MT7615DN (2x 2x2:2) 2.4GHz and 5GHz DBDC
- 1x MT7615NE (4x4:4) 5GHz
- 8 external antennas
BTN:
- 1x Reset button
- 1x WPS button
- 1x Turbo button
- 1x Touchlink button
- 1x ON/OFF switch
LEDS:
- 1x Red led (system status)
- 1x Blue led (system status)
- 7x Blue leds (wifi led + 5 ethernet ports + power)
USB:
- 1x USB 3.0 port
UART:
- 57600-8-N-1
J4
Everything works correctly.
Installation
------------
Flash the initramfs image in the OEM firmware interface
(http://192.168.10.1/update.shtml).
When Openwrt boots, flash the sysupgrade image otherwise you won't be
able to keep configuration between reboots.
(Procedure tested on fw M33A8.V5030.190716 and M33A8.V5030.201204)
Restore OEM Firmware
--------------------
Flash the firmware update available online directly from LUCI.
You can download it from:
https://www.wavlink.com/en_us/firmware/details/f2d247ecba.html
Warning: Remember to not keep settings!
Warning2: Remember to force the flash.
Notes
-----
1) Router mac addresses:
LAN XX:XX:XX:XX:XX:63 (factory @ 0xe006)
WAN XX:XX:XX:XX:XX:64 (factory @ 0xe000)
WIFI 2G/5G XX:XX:XX:XX:XX:65 (factory @ 0x04)
WIFI 5G XX:XX:XX:XX:XX:66 (factory @ 0x8004)
LABEL XX:XX:XX:XX:XX:65
In OEM firmware the DBDC wifi interfaces have these mac addresses:
2G) 82:XX:XX:XX:XX:65
5G) 80:XX:XX:XX:XX:65
While in OpenWrt the addresses are:
2G) 80:XX:XX:XX:XX:65
5G) 02:XX:XX:XX:XX:65
2) radio0 will show as 2G/5G interface but only 2G is really usable.
3) There is just one wifi led for all wifi interfaces.
It currently shows only the radio0 GHz wifi activity.
4) My unit was shipped with M33A8.V5030.190716 firmware which contains
the http://192.168.10.1/webcmd.shtml page. Entering "telnetd" in
the input box it will start the telnet daemon. Now you can access
the telnet console on port 2323 with these credentials:
username: admin2860
password: admin
5) The M33A8.V5030.201204 firmware version, doesn't contain anymore the
webcmd.shtml page. If your router is shipped with a previous firmware
version and you want to back it up, you can follow the back up
procedure of the WS-WN583A6.
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Most of the definitions for WN531A6 will be shared with WN533A8 in a
future commit, so put them in a shared DTSI.
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
In commit 7e614820a8 ("mpc85xx: add support for Extreme Networks
WS-AP3825i"), we borrowed a recipe convention from apm821xx for device
tree blob padding. Unfortunately, in the apm821xx target, the image
recipes name the device tree blob differently, meaning that in
mpc85xx, the padded dtb is never consumed.
Change the definition of `Build/dtb` so that it outputs the padded dtb
to the correct location for it to be consumed.
Also, rename the recipe to `Build/pad-dtb`, so it is clear we
are building and padding the device tree blob.
This change fixes Github issue #9779 [1].
[1]: https://github.com/openwrt/openwrt/issues/9779
Fixes: 7e614820a8 ("mpc85xx: add support for Extreme Networks WS-AP3825i")
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
The config for LEDS_UBNT_LEDBAR doesn't stay in mt7629 kconfig because
of its I2C dependency. Build it as a module and let buildroot handle
this config option instead.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Disable support for joysticks, micee and tablets. There's no actual
driver selected in kconfig, and including kernel support is just a
waste of space. Besides that, I believe nobody wants these on a router.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Remove patches and configuration for Linux 5.10 which have been left
in the tree despite the target having been switched to Linux 5.15.
Fixes: c283defa88 ("mediatek: switch to 5.15")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Set CONFIG_SCHED_MC in config-5.15 to have make the scheduler aware
of shared caches.
Reported-by: Rui Salvaterra <rsalvaterra@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
ubiblock devices should be used on NAND flash to store the uImage.FIT
in case the bootloader supports that -- otherwise only rootfs is stored
in UBI while the uImage.FIT contains only the kernel and dtb.
Hence there is no need to enable parsing partitions on NAND mtdblock
devices, it is even responsible for the ugly warning on-opening of the
mtdblock device now. Just don't do it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Instead of warning loudly about mtdblock devices being created, rather
just warn if they are actually used.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Last attempt on this has a typo and doen't work.
It seems that this is a common problem occurring on every kernel bump,
so let's enforce arch timer support for mt7623 with a patch instead.
Fixes: 9a22943eb2 ("mediatek: 5.15: re-enable arch timer on MT7623 as well")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This commit is completely based on the work of adron-s:
https://github.com/openwrt/openwrt/pull/4721#issuecomment-1101108651
The commit fixes the data corruption on TX packets. Packets are
transmitted, but their contents are replaced with zeros. This error is
caused by the lack of guard (50 ms) intervals between calibration phases.
This error is treated by adding mdelay(50) to the calibration function
code. In the original qca-ssda code [0], these mdelays were existing, but
in the ar41xx.c they are gone.
Tested on:
- Fritz!Box 4040
- Fritz!Box 7530
- Mikrotik SXTsq 5AC
- ZyXEL NBG6617
- [0] https://git.codelinaro.org/clo/qsdk/oss/lklm/qca-ssdk/-/blob/NHSS.QSDK.11.4/src/init/ssdk_init.c#L2072
Suggested-by: Serhii Serhieiev <adron@mstnt.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Nick Hainke <vincent@systemli.org>
the SPI-NAND driver switch breaks dts compatibility. It's too much work
to backport all ECC framework support to 5.10 so let's switch the target
to 5.15 instead.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This patch implements the spi-nand controller driver as an ECC-capable
spi-mem controller to use the upstream SPI-NAND driver.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
the OOB layout in MTK SNFI uses the 2nd byte, and anything using OOB
will make the block a bad-block in spi-nand driver.
Hack it for now. We need a proper solution upstream.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The bootloader does seem to not correctly patch in the MAC address for
eth0 / eth1 in some cases. While the root cause is not known, manually
applying the MAC-Address in preinit does not hurt.
Reported-by: Tom Herbers <freifunk@tomherbers.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
The WS-AP3825i uses Atheros PHYs which according to the datasheet
require the reset to be asserted for at least 1 ms.
This fixes broken eth1 upon soft-reboot. eth0 is no affected, as the
ifup / ifdown cycle in preinit prevents this issue from happening when
the system is ready.
Reported-by: Tom Herbers <freifunk@tomherbers.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
TP-Link RE650 v2 is largely similar to v1 that
is already supported by OpenWrt. Notable differences
is differnt SPI Flash - 8 MB instead of 16 MB
(from cFeon instead of Winbond) and a different
configuration of PCIE connections to wifi chips.
Otherwise it's largely the same product as v1
Hardware specification:
- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 8 MB - cFeon QH64A-104HIP
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART pinout - GND, RX, TX, labeled in the middle of the PCB,
requires soldering because they're not through holes.
Serial console @ 57600,8n1
Flash instructions:
Upload
openwrt-ramips-mt7621-tplink_re650-v2-squashfs-factory.bin
from the RE650 web interface.
TFTP recovery to stock firmware:
I didn't try recovering back to the stock firmware, however,
if there is such process for other RExxx devices, it seems like
it could be similar here.
Signed-off-by: Marcin Gordziejewski <openwrt@flicksfix.com>
There are two versions which are identical apart from the enclosure:
YunCore AX820: indoor ceiling mount AP with integrated antennas
YunCore HWAP-AX820: outdoor enclosure with external (N) connectors
Hardware specs:
SoC: MediaTek MT7621DAT
Flash: 16 MiB SPI NOR
RAM: 128MiB (DDR3, integrated)
WiFi: MT7905DAN+MT7975DN 2.4/5GHz 2T2R 802.11ax
Ethernet: 10/100/1000 Mbps x2 (WAN/PoE+LAN)
LED: Status (green)
Button: Reset
Power: 802.11af/at PoE; DC 12V,1A
Antennas: AX820(indoor): 4dBi internal; HWAP-AX820(outdoor): external
Flash instructions:
The "OpenWRT support" version of the AX820 comes with a LEDE-based
firmware with proprietary MTK drivers and a luci webinterface and
ssh accessible under 192.168.1.1 on LAN; user root, no password.
The sysupgrade.bin can be flashed using luci or sysupgrade via ssh,
you will have to force the upgrade due to a different factory name.
Remember: Do *not* preserve factory configuration!
MAC addresses as used by OEM firmware:
use address source
2g 44:D1:FA:*:0b Factory 0x0004 (label)
5g 46:D1:FA:*:0b LAA of 2g
lan 44:D1:FA:*:0c Factory 0xe000
wan 44:D1:FA:*:0d Factory 0xe000 + 1
The wan MAC can also be found in 0xe006 but is not used by OEM dtb.
Due to different MAC handling in mt76 the LAA derived from lan is used
for 2g to prevent duplicate MACs when creating multiple interfaces.
Signed-off-by: Clemens Hopfer <openwrt@wireloss.net>
When adding support to the router's built-in modem, this required
package was omitted, because it was already enabled in the image
configuration in use for testing, and this went unnoticed.
In result, the modem still isn't fully supported in official images.
As it is the primary WAN interface, add the missing package.
Fixes: e02fb42c53 ("comgt: support ZTE MF286R modem")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
The commit "uboot-mediatek: replace patch with accepted commit" changed
the name of the boot configuration property from 'bootconf' to
'u-boot,bootconf'. Reflect this change in the FIT partition parser.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
MPLS feature symbols are normally only set when kmod-mpls is enabled, but the
CONFIG_MPLS symbol they depend on could also have been selected by openvswitch
instead
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Adresses of device tree nodes are typically noted without the '0x'
prefix. While having the '0x' prefix doesn't hurt when using Linux,
more recent versions of U-Boot will add a duplicate ramoops node as a
simple string compare is used to check if the node is already present.
Remove the '0x' prefix to avoid the kernel warning resulting from
U-Boot adding a dupplicate pstore/ramoops node.
See also https://lists.denx.de/pipermail/u-boot/2022-April/481810.html
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The MediaTek's Crypto Engine module is only available for mt7623, in
which case it is built into the kernel.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
The MikroTik RouterBOARD wAP-2nd (sold as wAP) is a small
2.4 GHz 802.11b/g/n PoE-capable AP.
Specifications:
- SoC: Qualcomm Atheros QCA9533
- Flash: 16 MB (SPI)
- RAM: 64 MB
- Ethernet: 1x 10/100 Mbps (PoE in)
- WiFi: AR9531 2T2R 2.4 GHz (SoC)
- 3x green LEDs (1x lan, 1x wlan, 1x user)
See https://mikrotik.com/product/RBwAP2nD for more info.
Flashing:
TFTP boot initramfs image and then perform sysupgrade. Follow common
MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.
Note: following 781d4bfb39
The network setup avoids using the integrated switch and connects the
single Ethernet port directly. This way, link speed (10/100 Mbps) is
properly reported by eth0.
Signed-off-by: David Musil <0x444d@protonmail.com>
OrayBox X3A is a 2.4/5GHz dual band AC router, based on MediaTek MT7621.
Specification:
* SoC: MT7621
* RAM: DDR3 128 MiB
* Flash: 16 MiB NOR (XM25Q128)
* Wi-Fi: (single chip hosting both 2.4G and 5G)
* 2.4GHz: MT7615
* 5GHz: MT7615
* Ethernet: 3x 1000Mbps
* Switch: MT7530
* LED:
* Ethernet LEDs: On the back of the router, hardware-controlled.
* Status LEDs: One "pixel-like" RGB LED in the front of the router,
which is actually made up of 3 individual LEDs (with
dedicated GPIO pins) with the color of Red, Green,
and Blue.
The OEM firmware only lights up one color at a time to
indicate status, but that's very boring, and the colors
actually look great when combined, so I've improvised a
little and made them indicate netdev activities.
My test results:
GPIO 13/14/15
000 white (actually more like bright green or cyan
because the brightness of the green LED is
higher than red and blue)
001 bright purple
010 bright green
011 red
100 bright cyan
101 blue
110 green
111 off
Flash Layout:
0x0000000-0x0030000 : "u-boot"
0x0030000-0x0040000 : "u-boot-env"
0x0040000-0x0050000 : "factory"
0x0050000-0x0f50000 : "firmware"
/*0x0f50000 to 0x0fe0000 is undefined, same as OEM firmware*/
0x0fe0000-0x0ff0000 : "bdinfo"
0x0ff0000-0x1000000 : "reserve"
MAC address:
MAC Source Description Fix
A0:CX:XX:BX:XX:0D BDINFO_9 LAN(LABEL) DTS
A0:CX:XX:BX:XX:0E BDINFO_9 + 1 WAN DTS
A2:CX:XX:BX:XX:0F FACTORY_4 WIFI2G DTS
A2:CX:XX:CX:XX:0F SETBIT 7 (FACTORY_4 + 0x100000) WIFI5G HOTPLUG
A6:CX:XX:BX:XX:0F N/A WIFI2G_CLIENT N/A
A6:DX:XX:BX:XX:0F N/A WIFI5G_CLIENT N/A
Stock dmesg:
https://pastebin.com/2t2jwLdf
Stock Dumps:
https://pastebin.com/LDLxSWX3
Installation via SSH (does not void your warranty):
1. -----UNLOCK SSH-----
1.1 Set computer IP to DHCP mode, load 'http://10.168.1.1/cgi-bin/luci' in
your browser. Password is 'admin'.
1.2 Click the "备份且导出" (backup and export) button, and download the
config file.
1.3 Open the downloaded file with 7zip, navigate to '/etc/config/'.
1.4 Edit the file './system'. Change the '0' into '1' under
"config sys 'ssh'".
1.5 Save the file.
1.6 Upload the file by clicking the "导入且恢复" (import and recover)
button. The router will automatically reboot.
2. -----FLASH THE OPENWRT FIRMWARE-----
2.1 Use any scp tool to upload the 'sysupgrade' firmware to the '/tmp/'
folder to your router. It should be root@10.168.1.1 and the password
is 'admin'.
2.2 SSH into the router, also root@10.168.1.1 and the password is 'admin'.
2.3 **IMPORTANT** Type command 'dd if=/dev/mtd3 of=/tmp/firmware.bin', to
backup the stock firmware. Since the OEM does not provide firmware
download on their website, this is the only way to get it.
2.3 **ALSO IMPORTANT** Use any scp tool to download your backed-up stock
firmware from '/tmp/' to your local drive. Then you'd better use a hex
reading tool to have a rough look at it to make sure nothing is
corrupt. Or u can just back up again and cross check the MD5.
2.4 Type command 'mtd write /tmp/XXX.bin firmware', and it should flash
the firmware.
2.5 Verify that nothing went wrong. If you're confident, type 'reboot' and
reboot the router.
Revert to stock firmware:
1. load stock firmware using mtd (make sure u have a backup).
Signed-off-by: Ray Wang <raywang777@foxmail.com>
The ZyXEL GS1900-24HP v1 is a 24 port PoE switch with two SFP ports,
similar to the other GS1900 switches.
Specifications
--------------
* Device: ZyXEL GS1900-24HP v1
* SoC: Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash: 16 MiB
* RAM: Winbond W9751G8KB-25 64 MiB DDR2 SDRAM
* Ethernet: 24x 10/100/1000 Mbps, 2x SFP 100/1000 Mbps
* LEDs:
* 1 PWR LED (green, not configurable)
* 1 SYS LED (green, configurable)
* 24 ethernet port link/activity LEDs (green, SoC controlled)
* 24 ethernet port PoE status LEDs
* 2 SFP status/activity LEDs (green, SoC controlled)
* Buttons:
* 1 "RESET" button on front panel (soft reset)
* 1 button ('SW1') behind right hex grate (hardwired power-off)
* PoE:
* Management MCU: ST Micro ST32F100 Microcontroller
* 6 BCM59111 PSE chips
* 170W power budget
* Power: 120-240V AC C13
* UART: Internal populated 10-pin header ('J5') providing RS232;
connected to SoC UART through a TI or SIPEX 3232C for voltage
level shifting.
* 'J5' RS232 Pinout (dot as pin 1):
2) SoC RXD
3) GND
10) SoC TXD
Serial connection parameters: 115200 8N1.
Installation
------------
OEM upgrade method:
* Log in to OEM management web interface
* Navigate to Maintenance > Firmware > Management
* If "Active Image" has the first option selected, OpenWrt will need to be
flashed to the "Active" partition. If the second option is selected,
OpenWrt will need to be flashed to the "Backup" partition.
* Navigate to Maintenance > Firmware > Upload
* Upload the openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-initramfs-kernel.bin
file by your preferred method to the previously determined partition.
When prompted, select to boot from the newly flashed image, and reboot
the switch.
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-squashfs-sysupgrade.bin
U-Boot TFTP method:
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs
image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
* Since the GS1900-24HP v1 is a dual-partition device, you want to keep the
OEM firmware on the backup partition for the time being. OpenWrt can
only be installed in the first partition anyway (hardcoded in the
DTS). To ensure we are set to boot from the first partition, issue the
following commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x81f00000 192.168.1.10:openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-squashfs-sysupgrade.bin
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
[Add info on PoE hardware to commit message]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Converts extraction entries from 11-ath10k-caldata into
nvmem-cells in the individual board's device-tree file.
Same as commit 2047058 ("ipq806x: utilize nvmem-cells
for pre-calibration data")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Ansuel Smith <ansuelsmth@gmail.com>
There is a mr25h256 spi flash on this machine. From the mtd backup
of the stock firmware, this spi flash is empty.
[ 3.652745] spi_qup 1a280000.spi: IN:block:16, fifo:64, OUT:block:16,
fifo:64
[ 3.653925] spi-nor spi0.0: mr25h256 (32 Kbytes)
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
The Sophos AP100, AP100C, AP55, and AP55C are dual-band 802.11ac access
points based on the Qualcomm QCA9558 SoC. They share PCB designs with
several devices that already have partial or full support, most notably the
Devolo DVL1750i/e.
The AP100 and AP100C are hardware-identical to the AP55 and AP55C, however
the 55 models' ART does not contain calibration data for their third chain
despite it being present on the PCB.
Specifications common to all models:
- Qualcomm QCA9558 SoC @ 720 MHz (MIPS 74Kc Big-endian processor)
- 128 MB RAM
- 16 MB SPI flash
- 1x 10/100/1000 Mbps Ethernet port, 802.3af PoE-in
- Green and Red status LEDs sharing a single external light-pipe
- Reset button on PCB[1]
- Piezo beeper on PCB[2]
- Serial UART header on PCB
- Alternate power supply via 5.5x2.1mm DC jack @ 12 VDC
Unique to AP100 and AP100C:
- 3T3R 2.4GHz 802.11b/g/n via SoC WMAC
- 3T3R 5.8GHz 802.11a/n/ac via QCA9880 (PCI Express)
AP55 and AP55C:
- 2T2R 2.4GHz 802.11b/g/n via SoC WMAC
- 2T2R 5.8GHz 802.11a/n/ac via QCA9880 (PCI Express)
AP100 and AP55:
- External RJ45 serial console port[3]
- USB 2.0 Type A port, power controlled via GPIO 11
Flashing instructions:
This firmware can be flashed either via a compatible Sophos SG or XG
firewall appliance, which does not require disassembling the device, or via
the U-Boot console available on the internal UART header.
To flash via XG appliance:
- Register on Sophos' website for a no-cost Home Use XG firewall license
- Download and install the XG software on a compatible PC or virtual
machine, complete initial appliance setup, and enable SSH console access
- Connect the target AP device to the XG appliance's LAN interface
- Approve the AP from the XG Web UI and wait until it shows as Active
(this can take 3-5 minutes)
- Connect to the XG appliance over SSH and access the Advanced Console
(Menu option 5, then menu option 3)
- Run `sudo awetool` and select the menu option to connect to an AP via
SSH. When prompted to enable SSH on the target AP, select Yes.
- Wait 2-3 minutes, then select the AP from the awetool menu again. This
will connect you to a root shell on the target AP.
- Copy the firmware to /tmp/openwrt.bin on the target AP via SCP/TFTP/etc
- Run `mtd -r write /tmp/openwrt.bin astaro_image`
- When complete, the access point will reboot to OpenWRT.
To flash via U-Boot serial console:
- Configure a TFTP server on your PC, and set IP address 192.168.99.8 with
netmask 255.255.255.0
- Copy the firmware .bin to the TFTP server and rename to 'uImage_AP100C'
- Open the target AP's enclosure and locate the 4-pin 3.3V UART header [4]
- Connect the AP ethernet to your PC's ethernet port
- Connect a terminal to the UART at 115200 8/N/1 as usual
- Power on the AP and press a key to cancel autoboot when prompted
- Run the following commands at the U-Boot console:
- `tftpboot`
- `cp.b $fileaddr 0x9f070000 $filesize`
- `boot`
- The access point will boot to OpenWRT.
MAC addresses as verified by OEM firmware:
use address source
LAN label config 0x201a (label)
2g label + 1 art 0x1002 (also found at config 0x2004)
5g label + 9 art 0x5006
Increments confirmed across three AP55C, two AP55, and one AP100C.
These changes have been tested to function on both current master and
21.02.0 without any obvious issues.
[1] Button is present but does not alter state of any GPIO on SoC
[2] Buzzer and driver circuitry is present on PCB but is not connected to
any GPIO. Shorting an unpopulated resistor next to the driver circuitry
should connect the buzzer to GPIO 4, but this is unconfirmed.
[3] This external RJ45 serial port is disabled in the OEM firmware, but
works in OpenWRT without additional configuration, at least on my
three test units.
[4] On AP100/AP55 models the UART header is accessible after removing
the device's top cover. On AP100C/AP55C models, the PCB must be removed
for access; three screws secure it to the case.
Pin 1 is marked on the silkscreen. Pins from 1-4 are 3.3V, GND, TX, RX
Signed-off-by: Andrew Powers-Holmes <andrew@omnom.net>
This patch adds support for the MikroTik RouterBOARD 962UiGS-5HacT2HnT (hAP ac)
Specifications:
- SoC: QCA9558
- RAM: 128 MB
- Flash: 16 MB SPI
- 2.4GHz WLAN: 3x3:3 802.11n on SoC
- 5GHz WLAN: 3x3:3 802.11ac on QCA9880 connected via PCIe
- Switch: 5x 1000/100/10 on QCA8337 connected via RGMII
- SFP cage: connected via SGMII (tested with genuine & generic GLC-T)
- USB: 1x type A, GPIO power switch
- PoE: Passive input on Ether1, GPIO switched passthrough to Ether5
- Reset button
- "SFP" LED connected to SoC
- Ethernet LEDs connected to QCA8337 switch
- Green WLAN LED connected to QCA9880
Not working:
- Red WLAN LED
Installation:
TFTP boot initramfs image and then perform sysupgrade. Follow common
MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.
Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
Make u_env partition read/write - currently cannot write to it, which
blocks fw_setenv. This in turn breaks features like Advanced Reboot,
which rely on setting the environment variable boot_part (1 or 2).
Signed-off-by: Russell Morris <rmorris@rkmorris.us>
Hardware specifications:
SoC: MT7628DAN MIPS_24KEc@580MHz 2.4G-n 2x2
WiFi: MT7613BEN 5G-ac 160MHz 2x2
Switch: 4x100M built-in SoC
Flash: 16MB W25Q128JVSQ SPI-NOR
DRAM: 64MB built-in SoC
MAC addresses as verified by OEM firmware:
use address source
Lan/Wan/2G *:60 factory 0x4 (label)
5G *:64 factory 0x8000
Serial console: 57600,8n1
Installation:
Asus windows recovery tool:
install the Asus firmware restoration utility
unplug the router, hold the reset button while powering it on
release when the power LED flashes slowly
specify a static IP on your computer:
IP address: 192.168.1.75
Subnet mask 255.255.255.0
start the Asus firmware restoration utility, specify the factory image
and press upload
do NOT power off the device after OpenWrt has booted until the LED flashing
after flashing OpenWrt, there will be first no 5GHz Wifi available probably,
wait until blinking finishes and do a reboot
TFTP Recovery method:
set computer to a static ip, 192.168.1.75
connect computer to the LAN 1 port of the router
hold the reset button while powering on the router for a few seconds
send firmware image using a tftp client; i.e from linux:
$ tftp
tftp> binary
tftp> connect 192.168.1.1
tftp> put factory.bin
tftp> quit
do NOT power off the device after OpenWrt has booted until the LED flashing
after flashing OpenWrt, there will be first no 5GHz Wifi available probably,
wait until blinking finishes and do a reboot
Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
This device is from now-defunct BOLT! ISP in Indonesia.
The original firmware is based on mediatek SDK running linux 2.6 or 3.x in later revision.
Specifications:
- SoC: MediaTek MT7621
- Flash: 32 MiB NOR SPI
- RAM: 128 MiB DDR3
- Ethernet: 2x 10/100/1000 Mbps (switched, LAN + WAN)
- WIFI0: MT7603E 2.4GHz 802.11b/g/n
- WIFI1: MT7612E 5GHz 802.11ac
- Antennas: 2x internal, non-detachable
- LEDs: Programmable LEDs: 5 blue LEDs (wlan, tel, sig1-3) and 2 red LEDs (wlan and sig1)
Non-programmable "Power" LED
- Buttons: Reset and WPS
Instalation:
Install from TFTP
Set your PC IP to 10.10.10.3 and gateway to 10.10.10.123
Press "1" when turning on the router, and type the initramfs file name
You also need to solder pin header or cable to J4 or neighboring test points (T19-T21)
Pinouts from top to bottom: GND, TX, RX, VCC (3.3v)
Baudrate: 57600n8
There's also an additional gigabit transformer and RTL8211FD managed by the LTE module on the backside of the PCB.
Signed-off-by: Abdul Aziz Amar <abdulaziz.amar@gmail.com>
The Wavlink WL-WN531A3 is an AC1200 router with 5 fast ethernet ports
and one USB 2.0 port.
It's also known as Wavlink QUANTUM D4.
Hardware
--------
SoC: Mediatek MT7628AN
RAM: 64MB
FLASH: 8MB NOR (GigaDevice GD25Q64CSIG3)
ETH:
- 5x 10/100 Mbps Ethernet (4x LAN + 1x WAN)
WIFI:
- 2.4GHz: 1x (integrated in SOC) (2x2:2)
- 5GHz: 1x MT7612E (2x2:2)
- 4 external antennas
BTN:
- 1x Reset button
- 1x WPS button
- 1x Turbo button
- 1x Touchlink button
- 1x ON/OFF switch
LEDS:
- 1x Red led (system status)
- 1x Blue led (system status)
- 7x Blue leds (wifi led + 5 ethernet ports + power)
USB:
- 1x USB 2.0 port
UART:
- 57600-8-N-1
J1
O VCC +3,3V (near lan ports)
o RX
o TX
o GND
Everything works correctly.
Currently there is no firmware update available. Because of this, in
order to restore the OEM firmware, you must firstly dump the OEM
firmware from your router before you flash the OpenWrt image.
Backup the OEM Firmware
-----------------------
The following steps are to be intended for users having little to none
experience in linux. Obviously there are many ways to backup the OEM
firmware, but probably this is the easiest way for this router.
Procedure tested on M31A3.V4300.200420 firmware version.
1) Go to http://192.168.10.1/webcmd.shtml
2) Type the following line in the "Command" input box and then press enter:
mkdir /etc_ro/lighttpd/www/dev; cp /dev/mtd0ro /etc_ro/lighttpd/www/dev/mtd0ro; ls -la /etc_ro/lighttpd/www/dev/mtd0ro
3) After few seconds in the textarea should appear this output:
-rw-r--r-- 1 0 0 8388608 /etc_ro/lighttpd/www/dev/mtd0ro
If your output doesn't match mine, stop reading and ask for
help in the forum.
4) Open in another tab http://192.168.10.1/dev/mtd0ro to download the
content of the whole NOR. If the file size is 0 byte, stop reading
and ask for help in the forum.
5) Come back to the http://192.168.10.1/webcmd.shtml webpage and type:
rm /etc_ro/lighttpd/www/dev/mtd0ro; for i in 1 2 3 4 ; do cp /dev/mtd${i}ro /etc_ro/lighttpd/www/dev/mtd${i}ro; done; ls -la /etc_ro/lighttpd/www/dev/
6) After few seconds, in the textarea should appear this output:
-rw-r--r-- 1 0 0 196608 mtd1ro
-rw-r--r-- 1 0 0 65536 mtd2ro
-rw-r--r-- 1 0 0 65536 mtd3ro
-rw-r--r-- 1 0 0 8060928 mtd4ro
drwxr-xr-x 7 0 0 0 ..
drwxr-xr-x 2 0 0 0 .
If your output doesn't match mine, stop reading and ask for
help in the forum.
7) Open the following links to download the partitions of the OEM FW:
http://192.168.10.1/dev/mtd1rohttp://192.168.10.1/dev/mtd2rohttp://192.168.10.1/dev/mtd3rohttp://192.168.10.1/dev/mtd4ro
If one (or more) of these files are 0 byte, stop reading and ask
for help in the forum.
8) Store these downloaded files in a safe place.
9) Reboot your router to remove any temporary file in ram.
Installation
------------
Flash the initramfs image in the OEM firmware interface
(http://192.168.10.1/update.shtml).
When Openwrt boots, flash the sysupgrade image otherwise you won't be
able to keep configuration between reboots.
Restore OEM Firmware
--------------------
Flash the "mtd4ro" file you previously backed-up directly from LUCI.
Warning: Remember to not keep settings!
Warning2: Remember to force the flash.
Notes
-----
1) Router mac addresses:
LAN XX:XX:XX:XX:XX:9B (factory @ 0x28)
WAN XX:XX:XX:XX:XX:9C (factory @ 0x2e)
WIFI 2G XX:XX:XX:XX:XX:9D (factory @ 0x04)
WIFI 5G XX:XX:XX:XX:XX:9E (factory @ 0x8004)
LABEL XX:XX:XX:XX:XX:9D
2) There is just one wifi led for both wifi interfaces.
It currently shows only the 2.4 GHz wifi activity.
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
FRITZ!Box 7360 V2 and FRITZ!Box 7360 SL both use GPIOs 37 (for &phy0)
and GPIO 44 (for &phy1) to control the PHY's reset lines. FRITZ!Box 7362
SL however uses GPIO 45 (for &phy0) and GPIO 44 (for &phy1). Move the
GPIO reset definitions to each individual board .dts and while at it,
fix the GPIOs for the FRITZ!Box 7362 SL.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
This is required to support built-in modem of ZTE MF286R, in addition to
other external modems, such as MF831, MF910, MF920, which refuse to
reconfigure their remote MAC address, even if "locally administered" bit
is set, leading to dropped traffic towards the host. Add a workaround
for that issue already present in cdc_ether to rndis_host driver as
well.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Fix wrong CPU OPP for ipq8062. Revision of the SoC added an
extra 25mV for every pvs. Also fix the voltage min/max value
that were wrong.
Reviewed-by: Robert Marko robimarko@gmail.com
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
The existing device tree has incorrect definitions for usb3_0 and usb3_1
and the blocks they depend upon: their addresses and interrupts are
swapped. However, their clocks and resets are not. The result is that
the USB blocks are non-functional if only one of them is enabled.
This fix backports the definitions from mainline Linux 5.15 to
OpenWrt's 5.10 dtsi additions. See the relevant mainline code here:
https://github.com/torvalds/linux/blob/v5.17/arch/arm/boot/dts/qcom-ipq8064.dtsi#L1062-L1148
This fix does not break existing ports. But some ports may have enabled
both USB blocks even thought their board only implements one, because
enabling a single USB block would not have worked before this fix.
This means that revisiting all ports of ipq806x devices that implement
a single USB port is advised. This work must be done by maintainers that
can determine which USB block corresponds to the implemented port on
their hardware.
Note that this fix swaps the names of the hardware ports. This is
unfortunate, but will happen anyway when switching to kernel 5.15. Thus,
it is best to do this ASAP, before users get to depend on port names.
It is strongly recommended that this fix is backported to 22.03 before
its release. This will minimize the number of users affected by the port
name swap.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
The device was added for ar71xx target and dropped during the ath79
transition, mainly because of the ascii mac address stored in bdinfo
partition
Device page, http://wiki.openwrt.org/toh/hiwifi/hc6361
The vendor u-boot image accepts sysupgrade.bin image with specific
requirements, including having squashfs signature "hsqs" at file offset
0x140000. This is not possible now that OpenWrt kernel image is at
least 2MB with the signature at offset 0x240000.
Installation of current build of OpenWrt now requires a bootstrap step
of installing an earlier version first.
- If the vendor u-boot accepts sysupgrade image, hc6361 image of LEDE
release should work
- If the vendor u-boot accepts only verified flashsmt image, install
the one in the above device page. The image is based on Barrier
Breaker
SHA256SUM of the flashsmt image
81b193b95ea5f8e5c30cd62fa9facf275f39233be4fdeed7038f3deed2736156
After the bootstrap step, current build of OpenWrt can be installed
there fine.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
This is needed for devices with mac address stored in ascii format, e.g.
HiWiFi HC6361 to be ported in the following patch.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
For some reason useless labels and aliases have been propagated through
copy-paste. Before the issue spreads any further, this patch cleans up
all relevant DTS files to the canonical form, bringing ath79 in line
with other mikrotik platforms (ramips and ipq40xx).
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Specification:
- QCA9533 (650 MHz), 64 or 128MB RAM, 16MB SPI NOR
- 2x 10/100 Mbps Ethernet, with 802.3at PoE support (WAN)
- 2T2R 802.11b/g/n 2.4GHz
Flash instructions:
If your device comes with generic QSDK based firmware, you can login
over telnet (login: root, empty password, default IP: 192.168.188.253),
issue first (important!) 'fw_setenv' command and then perform regular
upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download
image to the device, SSH server is not available):
fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin
In case your device runs firmware with YunCore custom GUI, you can use
U-Boot recovery mode:
1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with
'tftp' image renamed to 'upgrade.bin'
2. Power the device with reset button pressed and release it after 5-7
seconds, recovery mode should start downloading image from server
(unfortunately, there is no visible indication that recovery got
enabled - in case of problems check TFTP server logs)
Signed-off-by: Clemens Hopfer <openwrt@wireloss.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Specification:
- QCA9563 (775MHz), 128MB RAM, 16MB SPI NOR
- 2T2R 802.11b/g/n 2.4GHz
- 2T2R 802.11n/ac 5GHz
- 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port)
LED for 5 GHz WLAN is currently not supported as it is connected directly
to the QCA9882 radio chip.
Flash instructions:
If your device comes with generic QSDK based firmware, you can login
over telnet (login: root, empty password, default IP: 192.168.188.253),
issue first (important!) 'fw_setenv' command and then perform regular
upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download
image to the device, SSH server is not available):
fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin
In case your device runs firmware with YunCore custom GUI, you can use
U-Boot recovery mode:
1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with
'tftp' image renamed to 'upgrade.bin'
2. Power the device with reset button pressed and release it after 5-7
seconds, recovery mode should start downloading image from server
(unfortunately, there is no visible indication that recovery got
enabled - in case of problems check TFTP server logs)
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
It's working well on all tested targets, so let's move
Gemini forward to v5.15. imx is already bumped so why not.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This creates a v5.15 baseline for the Gemini platform.
The main new attraction is the new crypto driver from
Corentin Labbe that we activate in the new config.
Config was refreshed.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The prerequisite DSA changes for the nice RTL8366RB improvements
are already backported so bring back these changes as well.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Adding the kernel configuration has accidentally been omitted when
enabling testing kernel 5.15. Add it now.
Fixes: 09f6200198 ("malta: enable testing kernel 5.15")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use ARMv8 Crypto Extensions for AES, ghash and sha256.
This results in a 16 times speed gain in speed for aes-128-ctr, 17x in
aes-128-gcm, and 9 times in sha256.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
This commit add some enabled symbols to generic config.
LTO is only supported by clang compiler and therefore should
be disabled in the generic config instead of duplicating this
symbol in each target. CONFIG_LTO_NONE do this job.
The second group of symbols is enabled by the options available
in the generic config and is therefore added here:
* CONFIG_AF_UNIX_OOB is selected by CONFIG_NET && CONFIG_UNIX,
* CONFIG_BINARY_PRINTF is selected by CONFIG_BPF_SYSCALL,
* CONFIG_NET_SOCK_MSG is selected by CONFIG_BPF_SYSCALL && CONFIG_NET.
The other symbols are disabled and should be in the generic config.
This commit also removes these symbols from subtargets.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
This was done by executing these commands:
$ make kernel_oldconfig CONFIG_TARGET=subtarget
$ make kernel_oldconfig CONFIG_TARGET=subtarget_platform
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
This was done by executing these commands:
$ make kernel_oldconfig CONFIG_TARGET=subtarget
$ make kernel_oldconfig CONFIG_TARGET=subtarget_platform
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
These devices only have 6MiB available for firmware, which is not
enough for recent release images, so move these to the tiny target.
Note for users sysupgrading from the previous ath79-generic snapshot
images:
The tiny target kernel has a 4Kb flash erase block size instead
of the generic target's 64kb. This means the JFFS2 overlay partition
containing settings must be reformatted with the new block size or else
there will be data corruption.
To do this, backup your settings before upgrading, then during the
sysupgrade, de-select "Keep Settings". On the CLI, use "sysupgrade -n".
If you forget to do this and your system becomes unstable after
upgrading, you can do this to format the partition and recover:
* Reboot
* Press RESET when Power LED blinks during boot to enter Failsafe mode
* SSH to 192.168.1.1
* Run "firstboot" and reboot
Signed-off-by: Joe Mullally <jwmullally@gmail.com>
Tested-by: Robert Högberg <robert.hogberg@gmail.com>
The sama7 sub target does not have USB support, the feature should not
be activated there. OpenWrt can automatically detect if the target
supports USB by using the scripts/target-metadata.pl script. With the
automatic detection USB support will only get activated on subtargest
which actually support USB like sam9x and sama5.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Bluetooth should be activated as an optional kmod package instead of
compiling it into the kernel.
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Use the ext4 driver for ext2 and ext3 too. This feature is activated in
the OpenWrt generic configuration.
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This was probably activated by mac80211 which was activated before.
mac80211 is build from backports in OpenWrt.
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
cgroups and namespaces should be configured by the generic OpenWrt
configuration and not for a specific target.
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Remove the configuration options which are building modules for the sub
target configuration.
These kernel modules are not packaged. Kernel options should only be
build as a module when they are selected by a kmod package and not by
setting them to =m in the target kernel configuration.
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
There are many ways to add external RTC to Raspberry Pi boards. Let's
include support for this for the whole target and while at it, sort
features alphabetically.
Fixes: #9594
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
For targets in U-Boot which were migrated to DM, the correct binary
image filename will be 'u-boot-dtb.img'. For backward compatibility,
keep support for both files and use the one which was generated with
our 'uboot-imx' package.
See also 'CONFIG_SPL_FS_LOAD_PAYLOAD_NAME' and 'CONFIG_OF_CONTROL' in
mainline U-Boot sources.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Upstream in commit 8b9c0cb46471 ("apalis_imx6: boot env configuration
updates") removed emmc legacy wrappers, but so far didn't included any
replacements. Fix it by simply defining the missing variables and UUID
gathering directly into the boot script.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[pepe2k@gmail.com: updated commit title for 2022.01]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
The WatchGuard Firebox M200 and M300 use a Marvell 88e1543 PHY for the
first 3 ethernet ports. This PHY is supported by the Marvell Alaska PHY
driver, so enable it.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
There are various reports on Github and in the forum that this commit
causes multiple problems.
This reverts commit ee6ba216d8.
Fixes: #9420
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
octeon/patches-5.10 -> octeon/patches-5.15
Removed 140-octeon_e300_support.patch as E300 support appears to be upstreamed.
Reworked 130-add_itus_support.patch to compensate for the upstreaming of E300
octeon/config-5.15
The following Kernel Symbols were ADDED:
Line 5: +CONFIG_AF_UNIX_OOB=y
Line 6: +CONFIG_AHCI_OCTEON=y
Line 9: +CONFIG_ARCH_KEEP_MEMBLOCK=y
Line 16: +CONFIG_ATA=y
Line 17: +CONFIG_BINARY_PRINTF=y
Line 29: +CONFIG_CPU_R4K_FPU=y
Line 45: +CONFIG_FWNODE_MDIO=y
Line 51: +CONFIG_GENERIC_FIND_FIRST_BIT=y
Line 59: +CONFIG_GLOB=y
Line 61: +CONFIG_GPIO_CDEV=y
Line 77: +CONFIG_LTO_NONE=y
Line 85: +CONFIG_MIPS_FP_SUPPORT=y
Line 93: +CONFIG_NET_SELFTESTS=y
Line 94: +CONFIG_NET_SOCK_MSG=y
Line 105: +CONFIG_PATA_OCTEON_CF=y
Line 106: +CONFIG_PATA_TIMINGS=y
Line 114: +CONFIG_PTP_1588_CLOCK_OPTIONAL=y
Line 121: +CONFIG_SATA_AHCI_PLATFORM=y
Line 122: +CONFIG_SATA_HOST=y
Line 124: +CONFIG_SCSI_COMMON=y
Line 132: +CONFIG_SOCK_RX_QUEUE_MAPPING=y
Line 157: +CONFIG_USB_XHCI_HCD=y
Line 158: +CONFIG_USB_XHCI_PLATFORM=y
The following kernel symbols were REMOVED:
Line 21: -CONFIG_BLK_SCSI_REQUEST=y
Line 37: -CONFIG_ENABLE_MUST_CHECK=y
Line 69: -CONFIG_HOLES_IN_ZONE=y
Line 102: -CONFIG_OF_NET=y
Line 140: -CONFIG_SYS_SUPPORTS_HUGETLBFS=y
Compiled for Itus Shield, Boots successfully, continuing to test
for existing 5.10 memory leak.
Signed-off-by: Donald Hoskins <grommish@gmail.com>
[refresh patches]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The memory leak is fixed by the kernel patches backported in the
previous commit.
This reverts commit 1fa8780056.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Use the kernel's built-in formula for computing this value.
The value applied by OpenWRT's sysctl configuration file does not scale
with the available memory, under-using hardware capabilities.
Also, that formula also influences net.netfilter.nf_conntrack_buckets,
which should improve conntrack performance in average (fewer connections
per hashtable bucket).
Backport upstream commit for its effect on the number of connections per
hashtable bucket.
Apply a hack patch to set the RAM size divisor to a more reasonable value (2048,
down from 16384) for our use case, a typical router handling several thousands
of connections.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
There is a hard to reproduce, even harder to track down memory leak in
Octeon since kernel 5.10. Mark octeon source-only until it is plugged.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This reverts commit 35d2bbc29b as we
believe we found that it is indeed an openssl issue, where openssl is
trying to use getrandom(2), but fails because this particular builder
has an ancient kernel without that syscall. We didn't get to the bottom
of why openssl doesn't fall back to something like /dev/random.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
When upgrading a TP-Link Archer C5 v1 from ar71xx to ath79,
the 5ghz radio stops working because the device path changed.
Same has been done for the Archer C7 before:
commit e19506f206 ("ath79: migrate Archer C7 5GHz radio device paths")
Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
Config option `ARM_ARCH_TIMER` has been removed during rebasing onto
5.15 kernel in commit 2b395c2982 ("imx: update config for 5.15").
Anyway, as stated in commit 8cdc356f8c ("mediatek: mt7623: Re-enable
ARM arch timer") config option `ARM_ARCH_TIMER` cannot be enabled in the
config directly; it is only selected by `HAVE_ARM_ARCH_TIMER`. We need
to enable the latter in our config.
Fixes: 2b395c2982 ("imx: update config for 5.15")
Reported-by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
In imx target we're sharing single, version agnostic kernel
`config-default` file, which doesn't work very well with current 5.10
and upcoming 5.15 kernel symbols as recent rebase onto 5.15 kernel
introduced in commit 2b395c2982 ("imx: update config for 5.15) has
introduced following regression with 5.10 kernel:
Marvell 88E6xxx Ethernet switch fabric support (NET_DSA_MV88E6XXX) [Y/n/m/?] y
Switch Global 2 Registers support (NET_DSA_MV88E6XXX_GLOBAL2) [Y/n/?] (NEW)
That NET_DSA_MV88E6XXX_GLOBAL2 kernel config symbol has been removed in
upstream commit 63368a7416df ("net: dsa: mv88e6xxx: Make global2 support
mandatory") in kernel version 5.12.
This issue could be probably fixed by introduction of separate kernel
config files for each currently used kernel versions and subtarget, but
it is not worth the hassle and resources as imx target is running mostly
upstream kernel, so lets fix it by switching to 5.15 version instead.
Fixes: 2b395c2982 ("imx: update config for 5.15")
Acked-by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The label has the MAC address of eth0, not the WLAN PHY address. We can
merge the definition back into ar7241_ubnt_unifi.dtsi, as both DTS
derived from it use the same interface for their label MAC addresses
after all.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Add Kernel 5.15 patches + config. This is currently only available for
the generic subtarget, as it was exclusively tested with this target.
Tested-on: Siemens WS-AP3610, Enterasys WS-AP3705i
Signed-off-by: David Bauer <mail@david-bauer.net>
Specify the switch ports in the DTS file.
Re-enable it after it was disabled by commit e9672b1a8f ("bcm53xx: switch to the
upstream DSA-based b53 driver").
Signed-off-by: SHIMAMOTO Takayoshi <takayoshi.shimamoto.360@gmail.com>
[rmilecki: reword commit & drop unneeded whitespace change]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
platform_nand_pre_upgrade() is gone since commit 790692dde2
("base-files: drop support for the platform_nand_pre_upgrade()").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Asus RT-AC88U is an AC3100 router featuring 9 Ethernet ports over the
integrated Broadcom and the external Realtek switch.
Hardware info:
* Processor: Broadcom BCM4709C0KFEBG dual-core @ 1.4 GHz
* Switch: BCM53012 in BCM4709C0KFEBG & external RTL8365MB
* DDR3 RAM: 512 MB
* Flash: 128 MB (ESMT F59L1G81LA-25T)
* 2.4GHz: BCM4366 4×4 2.4/5G single chip 802.11ac SoC
* 5GHz: BCM4366 4×4 2.4/5G single chip 802.11ac SoC
* Ports: 8 Ports, 1 WAN Ports
Flashing instructions:
* Boot to CFE Recovery Mode by holding the reset button while power-on.
* Connect to the router with an ethernet cable.
* Set IPv4 address of the computer to 192.168.1.2 subnet 255.255.255.0.
* Head to http://192.168.1.1.
* Reset NVRAM.
* Upload the OpenWrt image.
CFE bootloader may reject flashing the image due to image integrity check.
In that case, follow the instructions below.
* Rename the OpenWrt image as firmware.trx.
* Run a TFTP server and make it serve the firmware.trx file.
* Run the URL below on a browser or curl.
http://192.168.1.1/do.htm?cmd=flash+-noheader+192.168.1.2:firmware.trx+flash0.trx
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
[rmilecki: mark BROKEN until we sort out nvram & CFE recovery]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The tc package does not exits any more, it was split into tc-tiny,
tc-full and tc-bpf. Include tc-bpf by default into realtek images.
This increases the compressed image size by about 232KBytes.
Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The realtek target is not a router, but basic device, see DEVICE_TYPE.
The basic device type does not come with firewall by default, see
include/target.mk for details. The realtek target extended
DEFAULT_PACKAGES manually with firewall.
This changes the defaults to take firewall4 and nftables instead of
firewall and iptables. This also adds the additional package
kmod-nft-offload.
The only difference to the router type is the missing ppp,
ppp-mod-pppoe, dnsmasq and odhcpd-ipv6only package.
This increases the compressed image size by about 422KBytes.
Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Do not include the dnsmasq and odhcpd-ipv6only package by default any
more. These services are not needed on a switch. If someone needs this
it is still possible to use opkg or image builder to add them.
This decreases the compressed image size by about 165KBytes.
Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
So the upcoming changes needed for 5.15 can be reviewed easily.
Removed following upstreamed patches:
* 062-add-sun8i-h3-zeropi-support.patch
* 100-sunxi-h3-add-support-for-nanopi-r1.patch
* 101-sunxi-h5-add-support-for-nanopi-r1s-h5.patch
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Fixes following build issues:
Package kmod-r8169 is missing dependencies for the following libraries:
mdio_devres.ko
Package kmod-ixgbe is missing dependencies for the following libraries:
mdio_devres.ko
Package kmod-amd-xgbe is missing dependencies for the following libraries:
mdio_devres.ko
Signed-off-by: Petr Štetiar <ynezz@true.cz>
So the upcoming changes needed for 5.15 can be reviewed easily.
Removing following patches backported from 5.15:
* 101-v5.15-mfd-lpc_ich-Enable-GPIO-driver-for-DH89xxCC.patch
* 102-v5.15-platform-x86-add-meraki-mx100-platform-driver.patch
Removed upstreamed patch `300-pcengines_apu1_led.patch` in commit
1b40faf7e4ab ("leds: apu: extend support for PC Engines APU1 with newer
firmware")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Backports following fix:
hv: utils: add PTP_1588_CLOCK to Kconfig to fix build
The hyperv utilities use PTP clock interfaces and should depend a
a kconfig symbol such that they will be built as a loadable module or
builtin so that linker errors do not happen.
Prevents these build errors:
ld: drivers/hv/hv_util.o: in function `hv_timesync_deinit':
hv_util.c:(.text+0x37d): undefined reference to `ptp_clock_unregister'
ld: drivers/hv/hv_util.o: in function `hv_timesync_init':
hv_util.c:(.text+0x738): undefined reference to `ptp_clock_register'
References: https://lore.kernel.org/stable/20220328093115.7486-1-ynezz@true.cz/T/#u
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Using set_disk_ro() doesn't have the desired effect and instead of
just setting the single partition to be read-only it affects the
whole disk. Use the bd_read_only flag in struct block_device instead
to mark a partition being read-only.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport patch
8b6836d82470 ("net: dsa: mv88e6xxx: keep the pvid at 0 when VLAN-unaware")
from 5.15.
Keeping the pvid at 0 when VLAN-unaware makes it possible to drop the
hack introduced in commit 920eaab1d8 ("kernel: DSA roaming fix for
Marvell mv88e6xxx"). Dropping the hack makes it possible to use VLAN
interfaces with VID 1 on DSA ports without problems with FDB.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fix dedicated cpufreq for kernel 5.15 as they changed module
order and now it can happen that cpufreq probe after cache driver.
Also add lock between cache scaling in set_target as it's now required
by opp functions.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Now that smem actually free the leaked parts, when
a rootfs partition is detected, the kernel panics as
it try to free the static space allocated for the "ubi"
name. Change the logic and fix the name at the allocate_partition
function to correctly free the space allocated by smem.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Refresh patch for 5.15
Rework tweak patch to sync with upstream ipq8064 dtsi and fix
regression introduced.
Rename nand_controller to nand in every dts.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
the buildbots are having troubles with the image.
They seem to get "Killed" at the last step of the KERNEL rule:
|/cros-vbutil -k zImage.itb.vboot -c "root=PARTUUID=%U/PARTNROFF=1" -o zImage.itb.vboot.new
|make[4]: *** [Makefile:18: zImage.itb.vboot] Killed
Since the Google Wifi (Gale) is currently the only target in
this sub-target. So this means that subtarget has to be disabled
from the time being to not be picked up by the builders.
For people wanting to checkout out OpenWrt on the Google Wifi:
please compile it locally.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The inclusion of the kmod-leds-uleds into the userspace
nu801 package causes a circular dependency inside the
buildsystem... which causes it to be picked regardless
of other DEPENDS values.
In case of the mx100, this could be solved by moving the
kmod-leds-uled dependency to the kmod-meraki-mx100.
Bonus: drop @!LINUX_5_4 from kmod-meraki-mx100
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
There are 2 warning for ar8xxx swconfig.
- Fix not used dev variable when ETHERNET_PACKET_MANGLE
is not selected
- Convert fallthrough comment to compilation macro
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Backport qca8k mdio improvement patch merged upstream,
where we use eth packet when available to send mdio commands.
This should improve speed and cause less load on the CPU.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Prepare uImage.FIT partition parser for Linux 5.15
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Patches that add the additional AQR PHY ID-s is just copy/paste from 5.10
and kernel 5.11 dropped the ack_interrupt method for PHY IRQ handling,
instead handle_interrupt is used.
So, simply switch to using handle_interrupt like other upstream AQR PHY-s.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
After fixing the original 720 patch, it looks like more were added for
additional AQR ID-s.
Patches that add the additional AQR PHY ID-s is just copy/paste from 5.10
and kernel 5.11 dropped the ack_interrupt method for PHY IRQ handling,
instead handle_interrupt is used.
So, simply switch to using handle_interrupt like other upstream AQR PHY-s.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Standardize pending patch tcp_no_window_check patch as with
new kernel they added a check for global variables.
The 2 new condition are that they must be read-only or
the data pointer should not point to kernel/module global
data.
Remove the global variable and move it to a standard place
following other variables logic.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Rework hack patch in dir for kernel 5.15.
For the specific patch of packet mangeling introduce a new extra_priv_flags
as we don't have enough space to add additional flags in priv_flags.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Refresh qca8k backport patches for 5.15 kernel.
Vlan_prepare is now dropped and there were some changes
to vlan add/remove functions.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
In commit ab143647ef ("kernel: generic: improve FIT partition parser")
part_bits was bumped to 2 in order to allow up to 3 additional FIT
sub-images mapped into sub-partitions.
This change has to be reflected also in our local patch
420-mtd-set-rootfs-to-be-root-dev.patch
which still assumed part_bits==1 for mtdblock devices in case of
CONFIG_FIT_PARTITION=y.
Fixes: #9557
Fixes: ab143647ef ("kernel: generic: improve FIT partition parser")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This commit builds on previous efforts to add support
for Sophos devices.
* Add support for Sophos XG 85 with/without wireless
* Add support for Sophos XG 86 with/without wireless
Tested on Sophos XG 85w rev1 and XG 86 rev 1
Signed-off-by: Raylynn Knight <rayknight@me.com>
# CONFIG_PSTORE_COMPRESS_DEFAULT="deflate"
this can lead to confusion. Thankfully, in the KConfig
world this setting is still interpreted as disabled.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
For HiWiFi series devices, label_mac can be read from bdinfo partition,
and lan_mac, wlan2g_mac are same as the label_mac. Converting label_mac
to wlan5g_mac only needs to unset 6th bit. (It seems that all HiWiFi's
label_mac start with D4:EE)
For example:
label D4:EE:07:32:84:88
lan D4:EE:07:32:84:88
wan D4:EE:07:32:84:89
wlan2g D4:EE:07:32:84:88
wlan5g D0:EE:07:32:84:88
Tested on HiWiFi HC5661.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
at91/sama7 fails to build due to:
| Asymmetric (public-key cryptographic) key type (ASYMMETRIC_KEY_TYPE) [Y/?] y
| Asymmetric public-key crypto algorithm subtype (ASYMMETRIC_PUBLIC_KEY_SUBTYPE) [Y/?] y
| Asymmetric TPM backed private key subtype (ASYMMETRIC_TPM_KEY_SUBTYPE) [N/m/?] (NEW)
|Error in reading or end of file.
please note that asym_tpm (module) has been removed in 5.17:
<https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=d3cff4a9>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
removes usb-port remains as neither the WAC510 nor the WAC505
come with a USB port. Update the LED properties to phase out
labels and introduce generic node-names as well as adding
the color, function and function-enumerator properties.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
ARM Builds like sunxi/cortexa53 or the rpi family failed
to build due to a new symbols showing up:
|Google Firmware Drivers (GOOGLE_FIRMWARE) [Y/n/?] y
| Coreboot Table Access (GOOGLE_COREBOOT_TABLE) [M/n/y/?] m
| Coreboot Framebuffer (GOOGLE_FRAMEBUFFER_COREBOOT) [N/m/?] (NEW)
|Error in reading or end of file.
Fixes: e5b009e532 ("kernel: Package GOOGLE_FIRMWARE drivers")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The OCEDO Raccoon had significant packet-loss with cables longer than 50
meter. Disabling EEE restores normal operation.
Also change the ethernet config to reduce loss on sub-1G links.
Signed-off-by: David Bauer <mail@david-bauer.net>
Avoid flooding the log with the message below by increasing the log
level to debug:
mt7621-nand 1e003000.nand: Using programmed access timing: 31c07388
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The patch was rejected by upstream. The mtk_nand driver should be
modified to support the mt7621 flash controller instead. As there is no
newer version to backport, or no upstream version to fix bugs, let's
move the driver to the files dir under the ramips target. This makes it
easier to make changes to the driver while waiting for mt7621 support to
land in mtk_nand.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Modified the radio frequency hardware part of e2600ac c1/c2,
need to cooperate with the modified board.bin file, the device
can work normally.
Signed-off-by: 张 鹏 <sd20@qxwlan.com>
This commit replaces patch number 0703 with the upstream accepted
version. This patch requires backporting an additional patch to
avoid conflicts.
The only significant change is the lower maximum MTU. Packets with
lengths over 2400 may be dropped.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
This commit moves the patches for the r8152.c driver to the generic
directory. Previously they were only available on the bcm27xx target.
With these patches the Realtek RTL8153C, RTL8153D, RTL8156A and RTL8156B
chips are supported on all targets by the kmod-usb-net-rtl8152 module.
The RTL8156A and RTL8156B are the 2.5Gb/s Ethernet adapters.
The patches have been tested on TP-Link UE300 (RTL8153A) and UNITEK
1313B (RTL8156B).
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
This reverts commit 80b7a8a7f5.
Now that 5.10 is the default kernel for all platforms, we can
bring back the NU801 userspace driver for platforms that rely
on it. Currently it's used on the MX100 x86_64 target, but
other Meraki platforms use this controller.
Note that we also now change how we load nu801. The way we did
this previously with procd worked, but it meant it didn't load
until everything was up and working.
To fix this, let's call nu801 from boot and re-trigger the
preinit blink sequence. Since nu801 runs as a daemon this is
now something we can do.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
(removed empty line, currently only MX100 uses it so: @TARGET_x86)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This model, also know as "1&1 HomeServer", shares the same features as 7530.
The vendor firmware has artificial software limitations: only 2 of the 4
LAN-Ports are GBit, and the USB-Host is only v2.0.
With OpenWrt, USB is already working at v3.0.
Signed-off-by: Andre Heider <a.heider@gmail.com>
(updated commit message to reflect current state)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Google WiFi (codename: Gale) is an IPQ4019-based AP, with 2 Ethernet
ports, 2x2 2.4+5GHz WiFi, 512 MB RAM, 4 GB eMMC, and a USB type C port.
In its stock configuration, it runs a Chromium OS-based system, but you
wouldn't know it, since you can only manage it via a "cloud" +
mobile-app system.
The "v2" label is coded into the bootloader, which prefers the
"google,gale-v2" compatible string. I believe "v1" must have been
pre-release hardware.
Note: this is *not* the Google Nest WiFi, released in 2019.
I include "factory.bin" support, where we generate a GPT-based disk
image with 2 partitions -- a kernel partition (using the custom "Chrome
OS kernel" GUID type) and a root filesystem partition. See below for
flashing instructions.
Sysupgrade is supported via recent emmc_do_upgrade() helper.
This is a subtarget because it enables different features
(FEATURES=boot-part rootfs-part) whose configurations don't make sense
in the "generic" target, and because it builds in a few USB drivers,
which are necessary for installation (installation is performed by
booting from USB storage, and so these drivers cannot be built as
modules, since we need to load modules from USB storage).
Flashing instructions
=====================
Documented here:
https://openwrt.org/inbox/toh/google/google_wifi
Note this requires booting from USB storage.
Features
========
I've tested:
* Ethernet, both WAN and LAN ports
* eMMC
* USB-C (hub, power-delivery, peripherals)
* LED0 (R/G/B)
* WiFi (limited testing)
* SPI flash
* Serial console: once in developer mode, console can be accessed via
the USB-C port with SuzyQable, or other similar "Closed Case
Debugging" tools:
https://chromium.googlesource.com/chromiumos/third_party/hdctools/+/master/docs/ccd.md#suzyq-suzyqable
* Sysupgrade
Not tested:
* TPM
Known not working:
* Reboot: this requires some additional TrustZone / SCM
configuration to disable Qualcomm's SDI. I have a proposal upstream,
and based on IRC chats, this might be acceptable with additional DT
logic:
[RFC PATCH] firmware: qcom_scm: disable SDI at boot
https://lore.kernel.org/linux-arm-msm/20200721080054.2803881-1-computersforpeace@gmail.com/
* SMP: enabling secondary CPUs doesn't currently work using the stock
bootloader, as the qcom_scm driver assumes newer features than this
TrustZone firmware has. I posted notes here:
[RFC] qcom_scm: IPQ4019 firmware does not support atomic API?
https://lore.kernel.org/linux-arm-msm/20200913201608.GA3162100@bDebian/
* There's a single external button, and a few useful internal GPIO
switches. I haven't hooked them up.
The first two are fixed with subsequent commits.
Additional notes
================
Much of the DTS is pulled from the Chrome OS kernel 3.18 branch, which
the manufacturer image uses.
Note: the manufacturer bootloader knows how to patch in calibration data
via the wifi{0,1} aliases in the DTB, so while these properties aren't
present in the DTS, they are available at runtime:
# ls -l
/sys/firmware/devicetree/base/soc/wifi@a*/qcom,ath10k-pre-calibration-data
-r--r--r-- 1 root root 12064 Jul 15 19:11 /sys/firmware/devicetree/base/soc/wifi@a000000/qcom,ath10k-pre-calibration-data
-r--r--r-- 1 root root 12064 Jul 15 19:11 /sys/firmware/devicetree/base/soc/wifi@a800000/qcom,ath10k-pre-calibration-data
Ethernet MAC addresses are similarly patched in via the ethernet{0,1} aliases.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
(updated 901 - x1pro moved in the process)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
See my upstream questions:
https://lore.kernel.org/linux-arm-msm/20200913201608.GA3162100@bDebian/
This effectively reverts upstream Linux commit 13e77747800e ("firmware:
qcom: scm: Use atomic SCM for cold boot"), because Google WiFi boot
firmwares don't support the atomic variant.
This fixes SMP support for Google WiFi.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
See firmware-utils.git commits [1], which implemented the cros-vbutil
verified-boot payload-packing tool, and extended ptgen for the CrOS
kernel partition type. With these, it's now possible to package kernel +
rootfs to make disk images that can boot a Chrome OS-based system (e.g.,
Chromebooks, or even a few AP models).
Regarding PARTUUID= changes: Chromium bootloaders work well with a
partition number offset (i.e., relative to the kernel partition), so
we'll be using a slightly different root UUID line.
NB: I've made this support specific to ip40xx for now, because I only
plan to support an IPQ4019-based AP that uses a Chromium-based
bootloader, but this image format can be used for essentially any
Chromebook, as well as the Google OnHub, a prior Chromium-based AP using
an IPQ8064 chipset.
[1]
ptgen: add Chromium OS kernel partition support
https://git.openwrt.org/?p=project/firmware-utils.git;a=commit;h=6c95945b5de973026dc6f52eb088d0943efa96bb
cros-vbutil: add Chrome OS vboot kernel-signing utility
https://git.openwrt.org/?p=project/firmware-utils.git;a=commit;h=8e7274e02fdc6f2cb61b415d6e5b2e1c7e977aa1
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tel(co Electronics) X1 Pro is preventing ipq40xx generic
from building due to the KERNEL_SIZE.
Whenever bigger kernels are possible, if lzma is supported
is unknown.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Required to allow sysupgrades from OpenWrt 19.07.
Closes#7071
Fixes: 98fbf2edc0 ("ath79: move TPLINK_HWID/_HWREV to parent for tplink-safeloader")
Tested-by: J. Burfeind <git@aiyionpri.me>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
It is disabled in the generic kernel config and not used in any of the
other targets. There was no specific reason for enabling it, so let's be
consistent and remove it from the qoriq kernel config.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
As the LED controller is working now, we can make good use of the LEDs
now.
- Drop the model-name prefix
- Rename eth0 / eth1 LEDs to LAN1 / LAN2, as they are labeled as such
on the casing
- Enable wired LEDs in userspace
Signed-off-by: David Bauer <mail@david-bauer.net>
Move the GPIO extender to the SoC node. Otherwise, the legacy PowerPC
init code will not populate the BUS and thus never probe spi-gpio.
Signed-off-by: David Bauer <mail@david-bauer.net>
While it hasn't always been clear whether the "AP" is part of the model
name on the Ubiquiti website, we include it for all other pre-AC
variants (AP Pro and the AP Outdoor+). Add it to the original UniFi AP
as well for consistency.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* only map filesystems configured in 'loadables'
* allow mapping more than one filesystem (e.g. customization/branding
or localization in addition to rootfs)
* small cleaning here and there
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
If the selected boot configuration is stored by U-Boot in '/chosen'
node as 'bootconf' attribute, use that configuration to resolve the
block device used as rootfs. Fall back to use the default configuration
in case 'bootconf' is not present.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
a20-olinuxino-lime2 is currently having hard time with link detection of
certain 1000Mbit partners due to usage of generic PHY driver, probably
due to following missing workaround introduced in upstream in commit
3aed3e2a143c ("net: phy: micrel: add Asym Pause workaround"):
The Micrel KSZ9031 PHY may fail to establish a link when the Asymmetric
Pause capability is set. This issue is described in a Silicon Errata
(DS80000691D or DS80000692D), which advises to always disable the
capability. This patch implements the workaround by defining a KSZ9031
specific get_feature callback to force the Asymmetric Pause capability
bit to be cleared.
This fixes issues where the link would not come up at boot time, or when
the Asym Pause bit was set later on.
As a20-olinuxino-lime2 has Micrel KSZ9031RNXCC-TR Gigabit PHY since
revision H, so we need to use Micrel PHY driver on those devices.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Remove "a" character from the first line of patch
738-v5.14-01-net-dsa-qca8k-fix-an-endian-bug-in-qca8k-get-ethtool.patch
Otherwise `git am` fails to apply this patch which is annoying when
trying to do some development / rebasing.
Signed-off-by: Marek Behún <kabel@kernel.org>
uDPU has 2 LM75 compatible temperature sensors, so include the driver for
them by default in order to utilize them.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
uDPU provides a FIT based initramfs, but currently gets stuck after U-boot
starts the kernel at "Starting kernel..".
It is due to the load address being too low, so increase it in order to get
the initramfs booting again.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
As the upcoming release will be based on Linux 5.10 only, remove all
kernel configuration as well as patches for Linux 5.4.
There were no targets still actively using Linux 5.4.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Also known as the "Xiaomi Router AX3200" in western markets,
but only the AX6S is widely installation-capable at this time.
SoC: MediaTek MT7622B
RAM: DDR3 256 MiB (ESMT M15T2G16128A)
Flash: SPI-NAND 128 MiB (ESMT F50L1G41LB or Gigadevice GD5F1GQ5xExxG)
WLAN: 2.4/5 GHz 4T4R
2.4 GHz: MediaTek MT7622B
5 GHz: MediaTek MT7915E
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531B
LEDs/Keys: 2/2 (Internet + System LED, Mesh button + Reset pin)
UART: Marked J1 on board VCC RX GND TX, beginning from "1". 3.3v, 115200n8
Power: 12 VDC, 1.5 A
Notes:
U-Boot passes through the ethaddr from uboot-env partition,
but also has been known to reset it to a generic mac address
hardcoded in the bootloader.
However, bdata is also populated with the ethernet mac addresses,
but is also typically never written to. Thus this is used instead.
Installation:
1. Flash stock Xiaomi "closed beta" image labelled
'miwifi_rb03_firmware_stable_1.2.7_closedbeta.bin'.
(MD5: 5eedf1632ac97bb5a6bb072c08603ed7)
2. Calculate telnet password from serial number and login
3. Execute commands to prepare device
nvram set ssh_en=1
nvram set uart_en=1
nvram set boot_wait=on
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
4. Download and flash image
On computer:
python -m http.server
On router:
cd /tmp
wget http://<IP>:8000/factory.bin
mtd -r write factory.bin firmware
Device should reboot at this point.
Reverting to stock:
Stock Xiaomi recovery tftp that accepts their signed images,
with default ips of 192.168.31.1 + 192.168.31.100.
Stock image should be renamed to tftp server ip in hex (Eg. C0A81F64.img)
Triggered by holding reset pin on powerup.
A simple implementation of this would be via dnsmasq's
dhcp-boot option or using the vendor's (Windows only)
recovery tool available on their website.
Signed-off-by: Richard Huynh <voxlympha@gmail.com>
Telco X1 Pro is a Cat12 LTE-A Pro modem router.
Vendor firmware is based on a recent version of OpenWrt.
Flashing is possible via CLI using sysupgrade -F -n
The serial headers allow bootloader and console access
Serial setting: 115200 8N1
Brief Specifications:
IPQ4019 SoC
32MB flash
512MB RAM
4x gigabit LAN
1x gigabit WAN
Dual-band Wave-2 wifi
2x SMA LTE antenna connectors
2x RP-SMA wifi antennas
1x USB 2.0 port
1x Reset button
Serial headers installed
1x Nano SIM tray
1x Quectel EM-12G LTE-A Pro modem
1x M.2 slot attached to USB 3.0
1x internal micro SD card slot
Signed-off-by: Nicholas Smith <nicholas@nbembedded.com>
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 128 MB (DDR3)
- Flash: 16 MB (SPI NOR)
- WiFi: MT7615N (2.4GHz) and MT7615N (5Ghz)
- Switch: 1 WAN, 4 LAN (Gigabit)
- Buttons: Reset, WiFi Toggle, WPS
- LEDs: Power, Internet, WiFi 2.4G WiFi 5G
The R1 revision is identical to the A1 revision except
- No Config2 Parition, therefore
- factory partition resized to 64k from 128K
- Firmware partition offset is 0x50000 not 0x60000
- Firmware partitions size increased by 64K
- Firmware partition type is "denx,uimage", not "sge,uimage"
- Padding of image creation "uimage-padhdr 96" removed
Installation:
Update to the last D-Link firmware through web-ui before OpenWRT
installation then follow the instructions to patch your device using
D-Link FailsafeUI.
- D-Link FailsafeUI:
Power down the router, press and hold the reset button, then
re-plug it. Keep the reset button pressed until the internet LED stops
flashing, then jack into any lan port and manually assign a static IP
address in 192.168.0.0/24 other than 192.168.0.1 (e.g. 192.168.0.2)
and go to http://192.168.0.1
Flash with the factory image.
Signed-off-by: Igor Nazarov <tigron.dev@gmail.com>
Some vendors like Seeedstudio in their product [1] with Raspberry Pi
Compute Module 4 uses Microchip LAN7800 (USB 3.0 to Gigabit
Ethernet Bridge) - USB 3.0 extended from PCIe of CM4.
lsusb output:
```
Bus 002 Device 002: ID 0424:7800 Microchip LAN7800
```
Raspberry Pi 4 and even Compute Module 4 has many resources available
and for just one kernel module it is not necessary to add additional specific CM4 profiles.
Let's include it by default, so the both Ethernet ports will be usable
to have better user-experience. Because previous generation of Raspberry
Pi included LAN7800 Gigabit Ethernet by default and it is enabled there
[2] in kernel without additional kernel module, which was added recently [3].
After this commit in dmesg can be found this:
```
root@OpenWrt:~# dmesg | grep lan
[ 7.038889] lan78xx 2-3:1.0 (unnamed net_device) (uninitialized): int urb period 64
[ 7.090484] usbcore: registered new interface driver lan78xx
```
Tested and works with sysupgrade image.
[1] https://www.seeedstudio.com/Dual-GbE-Carrier-Board-with-4GB-RAM-32GB-eMMC-RPi-CM4-Case-p-5029.html
[2] 32c74552b2/target/linux/bcm27xx/bcm2709/config-5.4 (L437)
[3] 31647d8be8
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Kernel 5.6 introduced a new config symbol SERIAL_8250_16550A_VARIANTS.
In kernel 5.8, this symbol was changed to default to on on !x86, as some
embedded devices still use 16650A variants. Let's play safe here and
enable this symbol in the generic config, to avoid others from running
into this problem and having to spend several hours trying to bisect
this problem. While we could disable the symbol in the x86 target
configs, a 20ms boot time reduction really isn't worth the time wasted
on bisecting this issue.
Matt discovered this problem while working on adding support for the
WatchGuard Firebox M200 to the qoriq target, where it caused some
characters to be missing on the console output.
Reported-by: Matt Fawcett <mattytap@icloud.com>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reviewed-by: Rui Salvaterra <rsalvaterra@gmail.com>
- fix eth0 eth1 sharing same mac so it conforms to the behavior stated
in the original commit and the way it is in vendor firmware :
WAN is label, LAN is label +1 and WLAN is label +2
- add default leds config
- add default network config
Signed-off-by: Pascal Coudurier <coudu@wanadoo.fr>
Buildbot has reported following issue while crunching mpc85xx/p1010
subtarget:
Extreme Networks WS-AP3825i (WS_AP3825I) [N/y/?] (NEW)
Fix it by disabling that config symbol in target kernel config and while
at it fix DTS whitespace issue.
Fixes: 7e614820a8 ("mpc85xx: add support for Extreme Networks WS-AP3825i")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Without a partition subnode ofpart_core still parses direct subnodes as
partitions, but it ignores nodes with a compatible property. Due to
this, the switch to nvmem-cells made the urlader partition inaccessible.
As a result, the wireless network was broken, as the calibration data
is read from that partition by a script.
Fixes: #8983
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
The &spi node has #address-cells = <1> and #size-cells = <0>. Drop the
extra 0 in the reg property from the SPI flash node to ensure it's
number of cells matches the definition in the parent node. This also
makes the reg property for the SPI flash node consistent with all other
VR9 boards.
Fixes: eae6cac6a3 ("lantiq: add support for AVM FRITZ!Box 7362 SL")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Timo Schroeder reported:
"The TP-Link Archer VR2600v is stuck in a boot loop on written
snapshot image. It's able to boot using the snapshot uimage
though, but there ath10k firmware can't be found.
21.02.2 release version doesn't have either problem."
The VR2600v has a 512 byte header at the beginning of the
firmware that needs to be accounted for.
Fixes: f6a01d7f5c ("ipq806x: convert TP-Link Archer VR2600v to denx,uimage")
Reported-by: Timo Schroeder <der.timosch@gmail.com>
References: <https://github.com/openwrt/openwrt/issues/9467>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Hardware:
- SoC: Freescale P1020
- CPU: 2x e500v2 @ 800MHz
- Flash: 64MiB NOR (1x Intel JS28F512)
- Memory: 256MiB (2x ProMOS DDR3 V73CAG01168RBJ-I9H 1Gb)
- WiFi1: 2.4+5GHz abgn 3x3 (Atheros AR9590)
- Wifi2: 5GHz an+ac 3x3 (Qualcomm Atheros QCA9890)
- ETH: 2x PoE Gigabit Ethernet (2x Atheros AR8035)
- Power: 12V (center-positive barrel) or 48V PoE (active or passive)
- Serial: Cisco-compatible RJ45 next to 12V power socket (115200 baud)
- LED Driver: TI LV164A
- LEDs: (not functioning)
- 2x Power (Green + Orange)
- 4x ETH (ETH1 + ETH2) x (Green + Orange)
- 2x WiFi (WiFi2 + WiFi1)
Installation:
1. Grab the OpenWrt initramfs <openwrt-initramfs-bin>, e.g.
openwrt-mpc85xx-p1020-extreme-networks_ws-ap3825i-initramfs-kernel.bin.
Place it in the root directory of a DHCP+TFTP server, e.g. OpenWrt
`dnsmasq` with configuration `dhcp.server.enable_tftp='1'`.
2. Connect to the serial port and boot the AP with options
e.g. 115200,N,8. Stop autoboot in U-Boot by pressing Enter after
'Scanning JFFS2 FS:' begins, then waiting for the prompt to be
interrupted. Credentials are identical to the one in the APs
interface. By default it is admin / new2day: if these do not work,
follow the OEM's reset procedure using the reset button.
3. Set the bootcmd so the AP can boot OpenWrt by executing:
```uboot
setenv boot_openwrt "cp.b 0xEC000000 0x2000000 0x2000000; interrupts off; bootm start 0x2000000; bootm loados; fdt resize; fdt boardsetup; fdt chosen; bootm prep; bootm go;"
setenv bootcmd "run boot_openwrt"
saveenv
```
If you plan on going back to the vendor firmware - the bootcmd for it
is stored in the boot_flash variable.
4. Load the initramfs image to RAM and boot by executing
```uboot
setenv ipaddr <ipv4 client address>;
setenv serverip <tftp server address>;
tftpboot 0x2000000 <openwrt-initramfs-bin>;
interrupts off;
bootm start 0x2000000;
bootm loados;
fdt resize;
fdt boardsetup;
fdt chosen;
bootm prep;
bootm go;
```
5. Make a backup of the "firmware" partition if you ever wish to go back
to the vendor firmware.
6. Upload the OpenWrt sysupgrade image via SCP to the devices /tmp
folder.
7. Flash OpenWrt using sysupgrade.
```ash
sysupgrade /tmp/<openwrt-sysupgrade-bin>
```
Notes:
- We must step through the `bootm` process manually to avoid fdt
relocation. To explain: the stock U-boot (and stock Linux) are configured
with a very large CONFIG_SYS_BOOTMAPSZ (and the device's stock Linux
kernel is configured to be able to handle it). The U-boot version
predates the check for the `fdt_high` variable, meaning that upon fdt
relocation, the fdt can (and will) be moved to a very high address; the
default appears to be 0x9ffa000. This address is so high that when the
Linux kernel starts reading the fdt at the beginning of the boot process,
it encounters a memory access exception and panics[5]. While it is
possible to reduce the highest address the fdt will be relocated to by
setting `bootm_size`, this also has the side effect of limiting the
amount of RAM the kernel can use[3].
- Because it is not relocated, the flattened device tree needs to be
padded in the build process to guarantee that `fdt resize` has
enough space.
- The primary ethernet MAC address is stored (and set) in U-boot; they are
shimmed into the device tree by 'fdt boardsetup' through the
'local-mac-address' property of the respective ethernet node, so OpenWrt
does not need to set this at runtime. Note that U-boot indexes the
ethernet nodes by alias, which is why the device tree explicitly aliases
ethernet1 to enet2.
- LEDs do not function under OpenWrt. Each of 8 LEDs is connected to an
output of a TI LV164A shift register, which is wired to GPIO lines and
operates through bit-banged SPI. Unfortunately, I am unable to get the
spi-gpio driver to recognize the `led_spi` device tree node at all, as
confirmed by patching in printk messages demonstrating
spi-gpio.c::spi_gpio_probe never runs. It is possible to manually
articulate the shift register by exporting the GPIO lines and stepping
their values through the sysfs.
- Though they do not function under OpenWrt, I have left the pinout details
of the LEDs and shift register in the device tree to represent real
hardware.
- An archive of the u-boot and Linux source for the AP3825i (which is one
device of a range of devices code-named 'CHANTRY') be found here[1].
- The device has an identical case to both the Enterasys WS-AP3725i and
Adtran BSAP-2030[2] (and potentially other Adtran BSAPs). Given that
there is no FCC ID for the board itself (only its WLAN modules), it's
likely these are generic boards, and even that the WS-AP3725i is
identical, with only a change in WLAN card. I have ordered one to confirm
this.
- For additional information: the process of porting the board is
documented in an OpenWrt forum thread[4].
[1]: magnet:?xt=urn:btih:f5306a5dfd06d42319e4554565429f84dde96bbc
[2]: https://forum.openwrt.org/t/support-for-adtran-bluesocket-bsap-2030/48538
[3]: https://forum.openwrt.org/t/adding-openwrt-support-for-ws-ap3825i/101168/29
[4]: https://forum.openwrt.org/t/adding-openwrt-support-for-ws-ap3825i/101168
[5]: https://forum.openwrt.org/t/adding-openwrt-support-for-ws-ap3825i/101168/26
Tested-by: Martin Kennedy <hurricos@gmail.com>
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
This patch adds support for the Netgear WN3100RPv2
http://www.netgear.com/support/product/wn3100rpv2.aspx
Specifications:
- SoC: MediaTek MT7620A (580MHz, ramips)
- RAM: 32MB DDR
- Storage: 8MB NOR SPI flash
- Wireless: builtin MT7620A, 2x2:2 with u.FL connectors
- Ethernet: 1x100M
- Stock firmware based on OpenWRT Kamikaze
Like the EX2700, the bootloader expects a secondary image signature,
see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577
This device seems to be same hardware as a WN3000RPv3
Flash instructions:
- Use the Netgear WebUI to upgrade to OpenWRT using the factory image
(see note below),
- Use the sysupgrade image for upgrading versions from OpenWRT,
- TFTP recovery procedure can be used to flash the factory image
(preferred method).
Note:
- The WebUI may not reboot automatically, wait at least 5 minutes before
powercycling the device
Flashing using TFTP:
- Set you IP address to 192.168.1.10/24 (no gateway)
- Connect your machine to the Ethernet port
- Power off the device and wait for 10 seconds,
- Hold the reset button and power on the device (do not release reset),
- Hold the reset button until the green light is flashing (Approx. 15s)
- launch tftp, set mode to binary and connect to 192.168.1.1
- put the factory firmware image
- All leds will switch off (like a power off), this is normal
- Wait for the device to reboot in the new OpenWRT image (max 5 mins)
- The first boot will take longer than usual.
- After boot, the Device IP on the ethernet port is 192.168.1.1
Signed-off-by: Rodolphe de Saint Léger <rdesaintleger@gmail.com>
[drop unneeded includes in dts, wrap commit message]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This reverts commit 7bc20cb614.
It adds support for Netgear WN3100RPv2, but the commit title is wrong.
It will be re-added with the correct title.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This patch adds support for the Netgear WN3100RPv2
http://www.netgear.com/support/product/wn3100rpv2.aspx
Specifications:
- SoC: MediaTek MT7620A (580MHz, ramips)
- RAM: 32MB DDR
- Storage: 8MB NOR SPI flash
- Wireless: builtin MT7620A, 2x2:2 with u.FL connectors
- Ethernet: 1x100M
- Stock firmware based on OpenWRT Kamikaze
Like the EX2700, the bootloader expects a secondary image signature,
see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577
This device seems to be same hardware as a WN3000RPv3
Flash instructions:
- Use the Netgear WebUI to upgrade to OpenWRT using the factory image
(see note below),
- Use the sysupgrade image for upgrading versions from OpenWRT,
- TFTP recovery procedure can be used to flash the factory image
(preferred method).
Note:
- The WebUI may not reboot automatically, wait at least 5 minutes before
powercycling the device
Flashing using TFTP:
- Set you IP address to 192.168.1.10/24 (no gateway)
- Connect your machine to the Ethernet port
- Power off the device and wait for 10 seconds,
- Hold the reset button and power on the device (do not release reset),
- Hold the reset button until the green light is flashing (Approx. 15s)
- launch tftp, set mode to binary and connect to 192.168.1.1
- put the factory firmware image
- All leds will switch off (like a power off), this is normal
- Wait for the device to reboot in the new OpenWRT image (max 5 mins)
- The first boot will take longer than usual.
- After boot, the Device IP on the ethernet port is 192.168.1.1
Signed-off-by: Rodolphe de Saint Léger <rdesaintleger@gmail.com>
[drop unneeded includes in dts, wrap commit message]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
The DWR-961 A1 Wireless Router is based on the MT7620A SoC.
It's a merge of two Amit boards: DWR-960 with ethernet part
of Lava LR-25G001.
ROMID it's taken from Telenor branded version and it works with tested
device. Images from D-Link site for this router are from DWR-953 and it
have ROMID DLK6E2424001. I don't know if it's mistake on web-site
or if it's will require different image.
Specification:
- MediaTek MT7620A (580 Mhz)
- 128 MB of RAM
- 16 MB of FLASH
- 1x 802.11bgn radio
- 1x 802.11ac radio (MT7612 mpcie card)
- 5x 10/100/1000 Mbps Ethernet: 4xLAN and 1xWAN (QCA8337)
- 2x internal, non-detachable antennas (Wifi 2.4G)
- 3x external, detachable antennas (2x LTE, 1x Wifi 5G)
- 1x LTE modem cat 6
- UART (J5) header on PCB (57600 8n1)
- 13x LED, 2x button
- JBOOT bootloader
Installation:
Apply factory image via http web-gui or JBOOT recovery page
How to revert to OEM firmware:
- push the reset button and turn on the power. Wait until LED start
blinking (~10sec.)
- upload original factory image via JBOOT http (IP: 192.168.123.254)
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
The I2C controller used in QorIQ PPC devices requires the mpc-i2c
driver, which is enabled by the I2C_MPC kernel config symbol. Enable
this and its dependencies in the target kernel config, as is done for
the mpc85xx target.
This fixes missing hwmon, rtc and tpm devices on the M300.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Seeing failure to build because of missing symbols related to provisioning
CONFIG_KEXEC and signed images. Without this, if you set
CONFIG_KERNEL_KEXEC=y and try to build, target/linux will hang at:
scripts/kconfig/conf --syncconfig Kconfig
...
kexec system call (KEXEC) [Y/n/?] y
kexec file based system call (KEXEC_FILE) [Y/n/?] y
Verify kernel signature during kexec_file_load() syscall (KEXEC_SIG) [N/y/?] (NEW)
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Backport patches
381a730182f1 ("net: dsa: Move VLAN filtering syncing out of dsa_switch_bridge_leave")
108dc8741c20 ("net: dsa: Avoid cross-chip syncing of VLAN filtering")
from upstream (currently in net-next) to fix null-pointer dereference.
Signed-off-by: Marek Behún <kabel@kernel.org>
FCC ID: 2AG6R-AN700APIAC
Araknis AN-700-AP-I-AC is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+
this board is a Senao device:
the hardware is equivalent to EnGenius EAP1750
the software is modified Senao SDK which is based on openwrt and uboot
including image checksum verification at boot time,
and a failsafe image that boots if checksum fails
**Specification:**
- QCA9558 SOC MIPS 74kc, 2.4 GHz WMAC, 3x3
- QCA9880 WLAN PCI card, 5 GHz, 3x3, 26dBm
- AR8035-A PHY RGMII GbE with PoE+ IN
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM NT5TU32M16
- UART console J10, populated, RX shorted to ground
- 4 antennas 5 dBi, internal omni-directional plates
- 4 LEDs power, 2G, 5G, wps
- 1 button reset
NOTE: all 4 gpio controlled LEDS are viewed through the same lightguide
therefore, the power LED is off for default state
**MAC addresses:**
MAC address labeled as ETH
Only one Vendor MAC address in flash at art 0x0
eth0 ETH *:xb art 0x0
phy1 2.4G *:xc ---
phy0 5GHz *:xd ---
**Serial Access:**
the RX line on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin at J10
**Installation:**
Method 1: Firmware upgrade page:
(if you cannot access the APs webpage)
factory reset with the reset button
connect ethernet to a computer
OEM webpage at 192.168.20.253
username and password 'araknis'
make a new password, login again...
Navigate to 'File Management' page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm
wait about 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fd70000`
wait a minute
connect to ethernet and navigate to
192.168.20.253
Select the factory.bin image and upload
wait about 3 minutes
**Return to OEM:**
Method 1: Serial to load Failsafe webpage (above)
Method 2: delete a checksum from uboot-env
this will make uboot load the failsafe image at next boot
because it will fail the checksum verification of the image
ssh into openwrt and run
`fw_setenv rootfs_checksum 0`
reboot, wait a minute
connect to ethernet and navigate to
192.168.20.253
select OEM firmware image and click upgrade
Method 3: backup mtd partitions before upgrade
**TFTP recovery:**
Requires serial console, reset button does nothing
rename initramfs-kernel.bin to '0101A8C0.img'
make available on TFTP server at 192.168.1.101
power board, interrupt boot with serial console
execute `tftpboot` and `bootm 0x81000000`
NOTE: TFTP may not be reliable due to bugged bootloader
set MTU to 600 and try many times
**Format of OEM firmware image:**
The OEM software is built using SDKs from Senao
which is based on a heavily modified version
of Openwrt Kamikaze or Altitude Adjustment.
One of the many modifications is sysupgrade being performed by a custom script.
Images are verified through successful unpackaging, correct filenames
and size requirements for both kernel and rootfs files, and that they
start with the correct magic numbers (first 2 bytes) for the respective headers.
Newer Senao software requires more checks but their script
includes a way to skip them.
The OEM upgrade script is at
/etc/fwupgrade.sh
OKLI kernel loader is required because the OEM software
expects the kernel to be less than 1536k
and the OEM upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
Note on PLL-data cells:
The default PLL register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied at the PHY side,
using the at803x driver `phy-mode` setting through the DTS.
Therefore, the Ethernet Configuration registers for GMAC0
do not need the bits for RGMII delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
Signed-off-by: Michael Pratt <mcpratt@pm.me>
FCC ID: 2AG6R-AN500APIAC
Araknis AN-500-AP-I-AC is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+
this board is a Senao device:
the hardware is equivalent to EnGenius EAP1200
the software is modified Senao SDK which is based on openwrt and uboot
including image checksum verification at boot time,
and a failsafe image that boots if checksum fails
**Specification:**
- QCA9557 SOC MIPS 74kc, 2.4 GHz WMAC, 2x2
- QCA9882 WLAN PCI card 168c:003c, 5 GHz, 2x2, 26dBm
- AR8035-A PHY RGMII GbE with PoE+ IN
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM NT5TU32M16
- UART console J10, populated, RX shorted to ground
- 4 antennas 5 dBi, internal omni-directional plates
- 4 LEDs power, 2G, 5G, wps
- 1 button reset
NOTE: all 4 gpio controlled LEDS are viewed through the same lightguide
therefore, the power LED is off for default state
**MAC addresses:**
MAC address labeled as ETH
Only one Vendor MAC address in flash at art 0x0
eth0 ETH *:e1 art 0x0
phy1 2.4G *:e2 ---
phy0 5GHz *:e3 ---
**Serial Access:**
the RX line on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin at J10
**Installation:**
Method 1: Firmware upgrade page:
(if you cannot access the APs webpage)
factory reset with the reset button
connect ethernet to a computer
OEM webpage at 192.168.20.253
username and password 'araknis'
make a new password, login again...
Navigate to 'File Management' page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm
wait about 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fd70000`
wait a minute
connect to ethernet and navigate to
192.168.20.253
Select the factory.bin image and upload
wait about 3 minutes
**Return to OEM:**
Method 1: Serial to load Failsafe webpage (above)
Method 2: delete a checksum from uboot-env
this will make uboot load the failsafe image at next boot
because it will fail the checksum verification of the image
ssh into openwrt and run
`fw_setenv rootfs_checksum 0`
reboot, wait a minute
connect to ethernet and navigate to
192.168.20.253
select OEM firmware image and click upgrade
Method 3: backup mtd partitions before upgrade
**TFTP recovery:**
Requires serial console, reset button does nothing
rename initramfs-kernel.bin to '0101A8C0.img'
make available on TFTP server at 192.168.1.101
power board, interrupt boot with serial console
execute `tftpboot` and `bootm 0x81000000`
NOTE: TFTP may not be reliable due to bugged bootloader
set MTU to 600 and try many times
**Format of OEM firmware image:**
The OEM software is built using SDKs from Senao
which is based on a heavily modified version
of Openwrt Kamikaze or Altitude Adjustment.
One of the many modifications is sysupgrade being performed by a custom script.
Images are verified through successful unpackaging, correct filenames
and size requirements for both kernel and rootfs files, and that they
start with the correct magic numbers (first 2 bytes) for the respective headers.
Newer Senao software requires more checks but their script
includes a way to skip them.
The OEM upgrade script is at
/etc/fwupgrade.sh
OKLI kernel loader is required because the OEM software
expects the kernel to be less than 1536k
and the OEM upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
Note on PLL-data cells:
The default PLL register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied at the PHY side,
using the at803x driver `phy-mode` setting through the DTS.
Therefore, the Ethernet Configuration registers for GMAC0
do not need the bits for RGMII delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
Signed-off-by: Michael Pratt <mcpratt@pm.me>
FCC ID: U2M-AN300APIN
Araknis AN-300-AP-I-N is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+
this board is a Senao device:
the hardware is equivalent to EnGenius EWS310AP
the software is modified Senao SDK which is based on openwrt and uboot
including image checksum verification at boot time,
and a failsafe image that boots if checksum fails
**Specification:**
- AR9344 SOC MIPS 74kc, 2.4 GHz WMAC, 2x2
- AR9382 WLAN PCI on-board 168c:0030, 5 GHz, 2x2
- AR8035-A PHY RGMII GbE with PoE+ IN
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM 1839ZFG V59C1512164QFJ25
- UART console J10, populated, RX shorted to ground
- 4 antennas 5 dBi, internal omni-directional plates
- 4 LEDs power, 2G, 5G, wps
- 1 button reset
NOTE: all 4 gpio controlled LEDS are viewed through the same lightguide
therefore, the power LED is off for default state
**MAC addresses:**
MAC address labeled as ETH
Only one Vendor MAC address in flash at art 0x0
eth0 ETH *:7d art 0x0
phy1 2.4G *:7e ---
phy0 5GHz *:7f ---
**Serial Access:**
the RX line on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin at J10
**Installation:**
Method 1: Firmware upgrade page:
(if you cannot access the APs webpage)
factory reset with the reset button
connect ethernet to a computer
OEM webpage at 192.168.20.253
username and password 'araknis'
make a new password, login again...
Navigate to 'File Management' page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm
wait about 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fd70000`
wait a minute
connect to ethernet and navigate to
192.168.20.253
Select the factory.bin image and upload
wait about 3 minutes
**Return to OEM:**
Method 1: Serial to load Failsafe webpage (above)
Method 2: delete a checksum from uboot-env
this will make uboot load the failsafe image at next boot
because it will fail the checksum verification of the image
ssh into openwrt and run
`fw_setenv rootfs_checksum 0`
reboot, wait a minute
connect to ethernet and navigate to
192.168.20.253
select OEM firmware image and click upgrade
Method 3: backup mtd partitions before upgrade
**TFTP recovery:**
Requires serial console, reset button does nothing
rename initramfs-kernel.bin to '0101A8C0.img'
make available on TFTP server at 192.168.1.101
power board, interrupt boot with serial console
execute `tftpboot` and `bootm 0x81000000`
NOTE: TFTP may not be reliable due to bugged bootloader
set MTU to 600 and try many times
**Format of OEM firmware image:**
The OEM software is built using SDKs from Senao
which is based on a heavily modified version
of Openwrt Kamikaze or Altitude Adjustment.
One of the many modifications is sysupgrade being performed by a custom script.
Images are verified through successful unpackaging, correct filenames
and size requirements for both kernel and rootfs files, and that they
start with the correct magic numbers (first 2 bytes) for the respective headers.
Newer Senao software requires more checks but their script
includes a way to skip them.
The OEM upgrade script is at
/etc/fwupgrade.sh
OKLI kernel loader is required because the OEM software
expects the kernel to be less than 1536k
and the OEM upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
Note on PLL-data cells:
The default PLL register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied at the PHY side,
using the at803x driver `phy-mode` setting through the DTS.
Therefore, the Ethernet Configuration registers for GMAC0
do not need the bits for RGMII delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Some boards with firmware made with Senao SDK based on Linux 3.3
have the following lines in the OEM upgrade script at
/etc/fwupgrade.sh
local append=""
local CONF_TAR="/tmp/sysupgrade.tgz"
[ -f "$CONF_TAR" ] && append="-j $CONF_TAR"
and
\# check FWINFO filename
[ -z $(ls FWINFO* | grep -i ${modelname}) ] && errcode="1"
This addition also prevents needing to factory reset after flashing
for some boards that also have these lines in the script
\# Support downgrade but do default (Smart v2.x.x.x -> senaowrt v1.x.x.x)
[ $(ls FWINFO* | grep -i ${modelname} | cut -d "-" -f4 | cut -c 2) -lt 2 ] && append=""
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Panasonic Switch-M8eG PN28080K is a 8 + 1 port gigabit switch, based on
RTL8380M.
Specification:
- SoC : Realtek RTL8380M
- RAM : DDR3 128 MiB (Winbond W631GG8KB-15)
- Flash : SPI-NOR 32 MiB (Macronix MX25L25635FMI-10G)
- Ethernet : 10/100/1000 Mbps x8 + 1
- port 1-8 : TP, RTL8218B (SoC)
- port 9 : SFP, RTL8380M (SoC)
- LEDs/Keys : 7x / 1x
- UART : RS-232 port on the front panel (connector: RJ-45)
- 3:TX, 4:GND, 5:GND, 6:RX (pin number: RJ-45)
- 9600n8
- Power : 100-240 VAC, 50/60 Hz, 0.5 A
- Plug : IEC 60320-C13
- Stock OS : VxWorks based
Flash instruction using initramfs image:
1. Prepare the TFTP server with the IP address 192.168.1.111
2. Rename the OpenWrt initramfs image to "0101A8C0.img" and place it to
the TFTP directory
3. Download the official upgrading firmware (ex: pn28080k_v30000.rom)
and place it to the TFTP directory
4. Boot M8eG and interrupt the U-Boot with Ctrl + C keys
5. Execute the following commands and boot with the OpenWrt initramfs
image
rtk network on
tftpboot 0x81000000
bootm
6. Backup mtdblock files to the computer by scp or anything and reboot
7. Interrupt the U-Boot and execute the following commands to re-create
filesystem in the flash
ffsmount c:/
ffsfmt c:/
this step takes a long time, about ~ 4 mins
8. Execute the following commands to put the official images to the
filesystem
updatert <official image>
example:
updatert pn28080k_v30000.rom
this step takes about ~ 40 secs
9. Set the environment variables of the U-Boot by the following commands
setenv loadaddr 0xb4e00000
setenv bootcmd bootm
saveenv
10: Download the OpenWrt initramfs image and boot with it
tftpboot 0x81000000 0101A8C0.img
bootm
11: On the initramfs image, download the sysupgrade image and perform
sysupgrade with it
sysupgrade <imagename>
12: Wait ~ 120 seconds to complete flashing
Note:
- "Switch-M8eG" is a model name, and "PN28080K" is a model number.
Switch-M8eG has an another (old) model number ("PN28080"), it's not a
Realtek based hardware.
- Switch-M8eG has a "POWER" LED (Green), but it's not connected to any
GPIO pin.
- The U-Boot checks the runtime images in the flash when booting and
fails to execute anything in "bootcmd" variable if the images are not
exsisting.
- A filesystem is formed in the flash (0x100000-0x1DFFFFF) on the stock
firmware and it includes the stock images, configuration files and
checksum files. It's unknown format, can't be managed on the OpenWrt.
To get the enough space for OpenWrt, move the filesystem to the head
of "fs_reserved" partition by execution of "ffsfmt" and "updatert".
- On the other devices in the same series of Switch-M8eG PN28080K, the
INT pin on the PCA9555 is not connected to anywhere.
Back to the stock firmware:
1. Delete "loadaddr" variable and set "bootcmd" to the original value
on U-Boot:
setenv loadaddr
setenv bootcmd 'bootm 0x81000000'
on OpenWrt:
fw_setenv loadaddr
fw_setenv bootcmd 'bootm 0x81000000'
2. Perform reset or reboot
on U-Boot:
reset
on OpenWrt:
reboot
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Reviewed-by: Sander Vanheule <sander@svanheule.net>
The system status LED on Panasonic Switch-M8eG PN28080K is connected to
a PCA9539PW. To use the LED as a status LED of OpenWrt while booting,
enable the pca953x driver and built-in to the kernel.
Also enable CONFIG_GPIO_PCA953X_IRQ to use interrupt via RTL83xx GPIO.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Acked-by: Sander Vanheule <sander@svanheule.net>
The ZyXEL GS1900-24 v1 is a 24 port switch with two SFP ports, similar to
the other GS1900 switches.
Specifications
--------------
* Device: ZyXEL GS1900-24 v1
* SoC: Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash: 16 MiB
* RAM: Winbond W9751G8KB-25 64 MiB DDR2 SDRAM
* Ethernet: 24x 10/100/1000 Mbps, 2x SFP 100/1000 Mbps
* LEDs:
* 1 PWR LED (green, not configurable)
* 1 SYS LED (green, configurable)
* 24 ethernet port link/activity LEDs (green, SoC controlled)
* 2 SFP status/activity LEDs (green, SoC controlled)
* Buttons:
* 1 "RESET" button on front panel (soft reset)
* 1 button ('SW1') behind right hex grate (hardwired power-off)
* Power: 120-240V AC C13
* UART: Internal populated 10-pin header ('J5') providing RS232;
connected to SoC UART through a SIPEX 3232EC for voltage
level shifting.
* 'J5' RS232 Pinout (dot as pin 1):
2) SoC RXD
3) GND
10) SoC TXD
Serial connection parameters: 115200 8N1.
Installation
------------
OEM upgrade method:
* Log in to OEM management web interface
* Navigate to Maintenance > Firmware > Management
* If "Active Image" has the first option selected, OpenWrt will need to be
flashed to the "Active" partition. If the second option is selected,
OpenWrt will need to be flashed to the "Backup" partition.
* Navigate to Maintenance > Firmware > Upload
* Upload the openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-initramfs-kernel.bin
file by your preferred method to the previously determined partition.
When prompted, select to boot from the newly flashed image, and reboot
the switch.
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-squashfs-sysupgrade.bin
U-Boot TFTP method:
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs
image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
> Since the GS1900-24 v1 is a dual-partition device, you want to keep the
OEM firmware on the backup partition for the time being. OpenWrt can
only be installed in the first partition anyway (hardcoded in the
DTS). To ensure we are set to boot from the first partition, issue the
following commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x81f00000 192.168.1.10:openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-squashfs-sysupgrade.bin
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
Applies changes from 7774b86019 to new device committed later. Fix some
whitespace in the DTS. Use standard model name format in DTS.
Fixes: 6c743c3006 ("ramips: Add support for TP-Link TL-WPA8631P v3")
Signed-off-by: Joe Mullally <jwmullally@gmail.com>
Reported-by: Arınç ÜNAL <arinc.unal@arinc9.com>
