Commit Graph

1211 Commits

Author SHA1 Message Date
Lars Wessels
702366a30b lantiq: wifi mac fix for ARV752DPW
Set wifi mac from flash partition 'board_config' to
match the label on the device (Easybox 802).

Currently the wifi mac is always set to 00:0c:43:28:60:00.
eth0 and WiFi will now share the same mac (as in original firmware).

Signed-off-by: Lars Wessels <software@bytebox.org>
[improve commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-06 17:57:13 +02:00
Hauke Mehrtens
6062d85892 kernel: Update kernel 4.19 to version 4.19.131
Fixes:
- CVE-2020-10757

The "mtd: rawnand: Pass a nand_chip object to nand_release()" commit was
backported which needed some adaptations to other code.

Run tested: ath79
Build tested: ath79

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-07-04 21:12:42 +02:00
Aleksander Jan Bajkowski
58a6f06978 lantiq: remove unused PHY drivers on xrx200
All boards on xrx200 use builtin switch and there is no supported device
with external switch.
It was copy paste from xway subtarget and was added in commit 18b76c66fb.

Save 20.3 kB flash memory.

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
2020-06-27 00:19:13 +02:00
Petr Štetiar
e44e60b290 kernel: bump 5.4 to 5.4.48
Resolved merge conflict in the following patches:

 layerscape: 701-net-0213-dpaa2-eth-Add-CEETM-qdisc-support.patch
 ramips: 0013-owrt-hack-fix-mt7688-cache-issue.patch

Refreshed patches, removed upstreamed patch:

 bcm63xx: 020-v5.8-mtd-rawnand-brcmnand-fix-hamming-oob-layout.patch

Run tested: qemu-x86-64
Build tested: x86/64

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-06-22 12:51:22 +02:00
Adrian Schmutzler
340de1d154 lantiq: fritz7312: set maximum speed to 100 mbit on 5.4
The fritz 7312 does not support 1000 gbit. Advertising it makes it
worse. Some NIC will change to 1000 gibt and turn off and on again for
ever.

The previous patch in 36f628910b was only applied to the 4.19 file,
so let's just make it consistent with this patch.

Cc: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-21 21:30:36 +02:00
Adrian Schmutzler
ef9cee4980 lantiq: drop "CONFIG_HZ_100 is not set"
CONFIG_HZ_100 is not set to "y" in generic config anymore since
3a761c90af ("treewide: Don't diverge from upstream default HZ
settings on 4.19"), so we don't need to disable it anymore either.

This was the only remaining case in the entire tree.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-17 14:26:09 +02:00
Aleksander Jan Bajkowski
27724c2f54 lantiq: switch to 5.4
Runtime tested on BT Home Hub 5A and D-Link DWR-966.

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
2020-06-17 00:50:45 +02:00
Adrian Schmutzler
48c1fdd046 treewide: drop shebang from non-executable target files
This drops the shebang from all target files for /lib and
/etc/uci-defaults folders, as these are sourced and the shebang
is useless.

While at it, fix the executable flag on a few of these files.

This does not touch ar71xx, as this target is just used for
backporting now and applying cosmetic changes would just complicate
things.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-16 14:26:33 +02:00
Alexander Couzens
bf5d800578
lantiq: fritz 7360 v2: remove additional supported devices
The additional supported device isn't required since this is a new
device. Some board contains an addtional device,
those device were supported in earlier versions which used the
"old" image builder code.
To support an sysupgrade from such old version, there is the all caps
additional device.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-18 11:59:22 +02:00
Alexander Couzens
0962baae4e lantiq: fritz 7360 v2: rename device before it will be used
Use similiar naming scheme as ath79.
Since the fritz 7360 v2 was only in the tree for 2 days, there
is no compatibility for the old image.
Users which has installed the fritz 7360 v2 before this change, must
use sysupgrade --force to skip checks on the board.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-18 11:57:57 +02:00
Adrian Schmutzler
b24fd13024 lantiq: drop outdated kernel version switches from patches-5.4
This drops some ancient kernel version switches from patches on
lantiq target. The patch only adjusts the latest kernel 5.4, as
doing it a second time for an older kernel seems a waste of time
for a cosmetic change.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-17 18:36:21 +02:00
Yushi Nishida
78bebe680f
lantiq/xrx200: add support for the Fritzbox 7360v2
This commit adds support for the Fritzbox 7360v2

CPU: VR9 500MHz Cores: 2
RAM: 128 MB
NOR-Flash: 32 MB
WLAN: AR9287-BL1A

DECT is not working.

Thanks Sebastian Ortwein for adding 7360SL.
The dts file is derived from avm_fritz7360sl.dts.

Firmware can be flashed with this method:

1.) Set your client IP to 192.168.178.2
2.) Power on your your Fritzbox and connect to 192.168.178.1
    via ftp in the first 5 seconds.
3.) login with adam2/adam2
4.) type into the ftp prompt:

passive
binary
debug 1
quote MEDIA FLSH // (not FLASH)
put openwrt-lantiq-xrx200-avm_fritz7360v2-squashfs-sysupgrade.bin mtd1
// using the correct location for the squashfs-sysupgrade-firmware.bin

5.) wait till red light flashing turns off.
6.) type: exit

Run tested with kernel 4.19 and 5.4 on Fritzbox 7360 V2.

Issue:
Ethernet speed is slow, (iperf between a Xiaomi mir3g
and this router results in <80Mbits throughput
with a wired cable when using the gbit ports.)

Signed-off-by: Yushi Nishida <kyro2man@gmx.net>
2020-05-16 04:37:55 +02:00
Alexander Couzens
36f628910b lantiq/fritz 7312: set maximum speed to 100 mbit
The fritz 7312 does not support 1000 gbit. Advertising it makes it
worse. Some NIC will change to 1000 gibt and turn off and on again for
ever.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2020-04-21 00:01:49 +02:00
Petr Štetiar
5ecc0cfd6f kernel: bump 5.4 to 5.4.28
Changelog since 5.4.24 mentions CVE-2019-19769, CVE-2020-8648,
CVE-2020-8649 and CVE-2020-8647.

Removed upstreamed:

 generic: 507-v5.6-iio-chemical-sps30-fix-missing-triggered-buffer-depe.patch
 generic: 600-ipv6-addrconf-call-ipv6_mc_up-for-non-Ethernet-inter.patch
 bcm27xx: 950-0435-ASoC-pcm512x-Fix-unbalanced-regulator-enable-call-in.patch
 ipq806x: 701-stmmac-fix-notifier-registration.patch
 lantiq: 002-pinctrl-falcon-fix-syntax-error.patch
 octeontx: 0002-net-thunderx-workaround-BGX-TX-Underflow-issue.patch

Run tested: apu2, qemu-x86-64, apalis, a64-olinuxino, nbg6617
Build tested: sunxi/a53, imx6, x86/64, ipq40xx

Tested-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> [apu2]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-03-28 13:03:02 +01:00
Sungbo Eo
3f14f034fb treewide: omit IMAGE_SIZE argument from check-size
Now that check-size uses IMAGE_SIZE by default, we can skip the argument from
image recipes to reduce redundancy.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-03-21 20:02:55 +01:00
Sungbo Eo
5b392c7119 treewide: gather DEVICE_VARS into one place
Place DEVICE_VARS assignments at the top of the file or above Device/Default
to make them easier to find.

For ramips, remove redundant values already present in parent file.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-03-21 19:55:12 +01:00
Mathias Kresin
b66af9ac2d lantiq: kernel 5.4: enable JFFS2
We do not build images with a jffs2 rootfs, but jffs2 is still used as
filesystem for the rootfs_data.

Fixes: e3eaf57808 ("lantiq: kernel 5.4: debloat kernel config")
Signed-off-by: Mathias Kresin <dev@kresin.me>
2020-03-17 20:36:39 +01:00
Mathias Kresin
e3eaf57808 lantiq: kernel 5.4: debloat kernel config
The etop driver is used by all targets except xrx200.

Remove the UBIFS compression support for zlib and zstd from the xway
subtarget. The hardware is EOL for a long time and it's unlikely to ever
see a board shipped with an UBIFS using these compression methods.

Remove the JFFS2 support. Support for jjfs2 images was dropped years
ago.

It shrinks the compressed kernel up to 130 KByte.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2020-03-16 22:28:17 +01:00
Mathias Kresin
6bf179b270 lantiq: add Linux 5.4 support as testing kernel version
Switch to the mainline Lantiq PCIe PHY driver and update the vr9.dtsi
accordingly.

The Lantiq IRQ SMP support added upstream required changes to the SoC
dtsi as well.

Following changes are made to the Lantiq kernel patches:

  0005-lantiq_etop-pass-struct-device-to-DMA-API-functions.patch
  0006-MIPS-lantiq-pass-struct-device-to-DMA-API-functions.patch
    applied upstream

  0008-MIPS-lantiq-backport-old-timer-code.patch
    access_ok API update because it lost it's type (which was the first)
    parameter in upstream commit 96d4f267e40f95 ("Remove 'type' argument
    from access_ok() function")

  0024-MIPS-lantiq-autoselect-soc-rev-matching-fw.patch
    merged into 0026-MIPS-lantiq-Add-GPHY-Firmware-loader.patch

  0024-MIPS-lantiq-revert-DSA-switch-driver-PMU-clock-chang.patch
    revert upstream changes required for upstream xrx200 ethernet and
    xrx200 (DSA) switch driver but breaking our driver

  0026-MIPS-lantiq-Add-GPHY-Firmware-loader.patch
    required for our driver but dropped upstream, add former upstream
    version

  0028-NET-lantiq-various-etop-fixes.patch
    now has to use the phy_set_max_speed API instead of modifying
    phydev->supported. Also call ltq_dma_enable_irq() in
    ltq_etop_open() based on upstream commit cc973aecf0b054 ("MIPS:
    lantiq: Do not enable IRQs in dma open")

Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2020-03-16 22:28:17 +01:00
Martin Blumenstingl
3d5d56487d lantiq: linux 5.4: remove support for the linux,mtd-name OF property
This is referenced in two .dts but never actually used from userspace.
Drop support for this property because it's not used and because it
makes updating to Linux 5.4 harder (as the patch doesn't apply anymore).

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2020-03-16 22:28:16 +01:00
Mathias Kresin
005dedd348 lantiq: copy target to kernel 5.4
Duplicate kernel 4.19 config and patches for kernel 5.4.

Duplicate the devicetree source files as well, they need kernel 5.4
specific adjustments.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2020-03-16 22:28:16 +01:00
Mathias Kresin
0270b1995b lantiq: vgv7510kw22: fix missing wireless
For some reason pin 7 (gphy0_led1_pins) need to be set to output prior
to loading the PCI driver. Otherwise the wireless doesn't appear on the
PCI bus. Of course, it doesn't make much sense, since pin 7 is used to
drive the LAN1 led.

It can either be done by setting the pins function to GPHY or GPIO +
direction output. However, the pinctrl driver doesn't provide a way to
switch a pin to GPIO. It is done indirectly by the pinctrl driver at the
time a GPIO is requested (requesting a GPIO always resets the function
to GPIO).

Do it via pinmux driver, as it is always loaded first. Use the GPHY
function as it's the pins intended purpose for this board.

Fixes: FS#2895

Signed-off-by: Mathias Kresin <dev@kresin.me>
2020-03-16 22:28:16 +01:00
Petr Štetiar
9ba09653ad treewide: remove maintainer variable from targets
There is no such role as target maintainer anymore, one should always
send corresponding changes for the review and anyone from the commiters
is allowed to merge them or eventually use the hand break and NACK them.

Lets make it clear, that it is solely a community doing the maintenance
tasks.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Piotr Dymacz <pepe2k@gmail.com>
2020-03-16 22:21:45 +01:00
Mathias Kresin
f2d976f06e lantiq: move mux for pins into subnodes
The mux need to be defined in a subnode to be considered by the pinctrl
framework. These muxes aren't set as expected and might cause not
working subsystems.

Fixes: 8e7b573b7a ("lantiq: dts: assign the PCI pins to the PCI controller node")
Fixes: dcb5e52209 ("lantiq: dts: assign the STP pins to the STP GPIO controller node")
Fixes: 660200e53d ("lantiq: dts: assign the GPHY LED pins to the Ethernet controller node")
Signed-off-by: Mathias Kresin <dev@kresin.me>
2020-03-15 21:38:05 +01:00
Sungbo Eo
4caaa778f7 kernel: make kmod-i2c-core selected by dependent modules
Currently kmod-i2c-* will not get into images unless kmod-i2c-core is added to
DEVICE_PACKAGES as well. By changing the dependencies from "depends on" to
"select", we do not have the issue anymore.

Furthermore, we can remove most occurrences of the package from DEVICE_PACKAGES
and similar variables, as it is now pulled by dependent modules such as:
- kmod-hwmon-lm75
- kmod-i2c-gpio
- kmod-i2c-gpio-custom
- kmod-i2c-mux
- kmod-i2c-ralink

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-03-13 15:40:43 +01:00
Sungbo Eo
90daff4cf8 build: image: move IMAGE_SIZE to image.mk
IMAGE_SIZE is widely used in many targets. Declare it in the default template to
clean up redundant code. This also prevents deriving IMAGE_SIZE unintentionally
from the previously defined device.

While at it, remove duplicate KERNEL_SIZE declaration.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-03-11 18:25:06 +01:00
Aleksander Jan Bajkowski
84845123fe kernel: remove non-existant symbols from 4.19 config
These symbols only exist in kernel version <= 4.15

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
2020-02-22 16:38:41 +01:00
Adrian Schmutzler
2dc0a8c180 lantiq: tidy up image/Makefile
This harmonizes indent for Build blocks and removes multiple empty
lines.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-24 18:52:41 +01:00
Adrian Schmutzler
719e106855 lantiq: fix setting SOC to DEFAULT_SOC
This adds the missing assignment of DEFAULT_SOC to the SOC variable
by default.

Fixes: 09ee51c614 ("lantiq: define SOC only once for uniform targets")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-24 18:48:47 +01:00
Adrian Schmutzler
09ee51c614 lantiq: define SOC only once for uniform targets
In lantiq there are several subtarget where all devices have the
same value set to the SOC variable for each device individually.

This patch introduces a non-device-dependent variable DEFAULT_SOC,
which is used if no specific SOC is set for a device, and thus reduces
the number of redundant definitions drastically.

This is applied to all subtargets except xway, as only the latter has
two different SOCs.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-24 18:38:53 +01:00
Adrian Schmutzler
d9a0794f8d lantiq: move DTS_DIR variable out of Device definition
The DTS_DIR variable is not a device variable, thus it should not
be set inside Device/Default but globally.

Fixes: c640370939 ("lantiq: use soc_vendor_device scheme on DTS file")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-24 18:35:25 +01:00
Adrian Schmutzler
44cb4fd5e6 lantiq: fix model name for BT Home Hub 3 Type A
The number 3 was accidentally removed from the name during split
of DEVICE_TITLE.

Fixes: fd66687058 ("lantiq: split up DEVICE_TITLE")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-24 18:32:11 +01:00
Adrian Schmutzler
2fe464a712 lantiq: reorganize 02_network board.d files
This reorganizes 02_network board.d files based on what's done for
ath79 and ramips: Instead of putting all settings into a single big
case, the interface/dsl/MAC address setup is put into separate
functions with a specific switch case for each of them. This makes
grouping of devices much easier and should be easier to read, too.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-14 22:04:44 +01:00
Adrian Schmutzler
18e089aaed lantiq: move common DSL setup into lantiq.sh
DSL setup consists of the same commands for all subtargets, so move it
into a helper function.

While at it, remove shebang from library file.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-14 22:04:37 +01:00
Adrian Schmutzler
355f0444f3 lantiq: split base-files into subtargets
This splits the device-dependent base-files into subtarget directories,
like done recently for ath79 and ramips. While this increases the
overall lines of codes, it will make the code per subtarget smaller
and easier to keep track of features and devices.

While at it, several variables at the top of 02_network are removed,
as they were never changed. The values are put directly into the
function calls where they are used.

Remove unneeded LED setup from 01_leds, and remove 01_leds entirely
for falcon subtarget (as it is not used there).

Applies alphabetic reordering to device cases in base-files.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-14 22:04:29 +01:00
Adrian Schmutzler
f943d84615 lantiq: use shared code for LED migration
Shared base-files package contains functions for LED migration that
are already used by several targets. Apply those also to lantiq and
drop the (redundant) local code.

While at it, reorder board names in file.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-03 00:07:00 +01:00
Adrian Schmutzler
ed3e1bd2cc lantiq: remove includes of non-existent /lib/functions/lantiq.sh
lantiq.sh is still included in files which do not use it anymore.
Remove the includes.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-03 00:05:30 +01:00
Koen Vandeputte
e115fa478f kernel: bump 4.19 to 4.19.90
Refreshed all patches.

Remove upstreamed:
- 010-dmaengine-dw-dmac-implement-dma-prot.patch
- 950-0148-Increase-firmware-call-buffer-size-to-48-bytes.patch
- 950-0206-Mailbox-firmware-calls-now-use-kmalloc-2749.patch
- 402-leds-trigger-netdev-fix-handling-on-interface-rename.patch

Fixes:
- CVE-2019-19332

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
[Add 010-dt-bindings-dmaengine-dw-dmac-add-protection-control.patch]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-12-24 15:34:43 +01:00
Kevin Schmidt
77e27e0f53 lantiq: enable 5ghz wifi on VR200/VR200v
Enable mt76 driver on VR200/VR200v.

Signed-off-by: Kevin Schmidt <kevin.patrick.schmidt@googlemail.com>
2019-12-23 00:04:18 +01:00
Aleksander Jan Bajkowski
692390225d lantiq: fix phys led
led2l and led2h value is incorrectly set by led3l and led3h.
Bug was introduced in commit: 863e79f8d5

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Fixes: 863e79f8d5 ("lantiq: add support for kernel 4.9")
2019-12-23 00:04:18 +01:00
Adrian Schmutzler
e2eb6d5829 lantiq: move include to parent falcon_lantiq_easy98000.dtsi
This moves the include of lantiq.dtsi from the DTS files to the
parent falcon_lantiq_easy98000.dtsi.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-22 01:24:23 +01:00
Adrian Schmutzler
397aa5d37d lantiq: remove ar9_lantiq_easy50810.dts
This file seems to be orphaned, no device setup existing for it.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-22 01:24:23 +01:00
Adrian Schmutzler
c640370939 lantiq: use soc_vendor_device scheme on DTS file
This renames lantiq DTS(I) files to follow soc_vendor_device scheme.
This will make DTS files easier to maintain.

As a side effect, DTS file name can be derived from device node
names now, only having to specify a SOC variable in Makefiles.

While at it, move files to arch/mips/boot/dts/lantiq subfolder.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-22 01:24:23 +01:00
Adrian Schmutzler
de6dd7a8db lantiq: split device definitions into files
This splits device definitions into several *.mk files to increase
overview.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-22 01:24:23 +01:00
Martin Blumenstingl
4c88b3b5dc lantiq: dts: assign the ASC pins to the serial controller node
Assign the ASC pins to the serial controller node instead of using pin
hogging (where pins are assigned to the pin controller).
This is the preferred way of assigning pins upstream.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2019-12-22 01:24:23 +01:00
Martin Blumenstingl
8e7b573b7a lantiq: dts: assign the PCI pins to the PCI controller node
Assign the PCI pins to the PCI controller node instead of using pin
hogging (where pins are assigned to the pin controller).
This is the preferred way of assigning pins upstream.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2019-12-22 01:24:23 +01:00
Martin Blumenstingl
dcb5e52209 lantiq: dts: assign the STP pins to the STP GPIO controller node
Assign the STP pins to the STP GPIO controller node instead of using
pin hogging (where pins are assigned to the pin controller).
This is the preferred way of assigning pins upstream.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2019-12-22 01:24:23 +01:00
Martin Blumenstingl
660200e53d lantiq: dts: assign the GPHY LED pins to the Ethernet controller node
Assign the GPHY LED pins to the Ethernet controller node instead of
using pin hogging (where pins are assigned to the pin controller).
This is the preferred way of assigning pins upstream.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2019-12-22 01:24:23 +01:00
Martin Blumenstingl
7298c25f74 lantiq: dts: assign the NAND pins to the nand-controller node
Assign the NAND pins to the NAND controller node instead of using pin
hogging (where pins are assigned to the pin controller).
This is the preferred way of assigning pins upstream.

While here, define all NAND pins (CLE, ALE, read/RD, ready busy/RDY and
CE/CS1). This means that the pinctrl subsystem knows that these pins are
in use and cannot be re-assigned as GPIOs for example.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2019-12-22 01:24:23 +01:00
Martin Blumenstingl
edb0a936f0 lantiq: dts: define the SPI pins in {amazonse,ar9,vr9}.dtsi
Define the SPI pins in the corresponding SoCs.dtsi and assign them to
the SPI controller node. All known boards use CS4 and it's likely that
this is hardcoded in bootrom so this doesn't bother with having
per-board SPI pinmux settings.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2019-12-22 01:24:23 +01:00
Martin Blumenstingl
b3bdfd5df5 lantiq: dts: assign the MDIO pins to the gsw node
Assign the MDIO pins to the switch node instead of using pin hogging
(where pins are assigned to the pin controller).
This is the preferred way of assigning pins upstream.

This converts amazonse, ar9 and vr9. danube is skipped because the pin
controller doesn't define a pinmux for the MDIO pins (some of the SoC
pads may be hardwired to the MDIO pins instead of being configurable).

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2019-12-22 01:24:23 +01:00
Koen Vandeputte
88ca372b5a kernel: bump 4.19 to 4.19.88
Refreshed all patches.

Remove upstreamed:
- 0004-boot-sq201-from-sda1.patch
- 500-v4.20-ubifs-Fix-default-compression-selection-in-ubifs.patch
- 0003-usb-dwc2-use-a-longer-core-rest-timeout-in-dwc2_core.patch

Altered patches:
- 0011-ARM-dts-Fix-up-SQ201-flash-access.patch
- 400-mtd-add-rootfs-split-support.patch
- 0101-pci-mediatek-backport-fix-pcie.patch

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-12-10 09:50:42 +01:00
Adrian Schmutzler
231dc26867 treewide: remove dts-v1 identifier from DTSI files
The "/dts-v1/;" identifier is supposed to be put once at the beginning
of a device tree file. Thus, it makes no sense to provide it a second
time in to-be-included DTSI files.

This removes the identifier from all DTSI files in /target/linux.

Most of the DTS files in OpenWrt do contain the "/dts-v1/;". It is
missing for most of the following targets, though:
mvebu, ipq806x, mpc85xx, ipq40xx

This does not touch ipq806x for now, as the bump to 4.19 is close.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-08 16:44:06 +01:00
Koen Vandeputte
f19e471f32 kernel: bump 4.19 to 4.19.86
Refreshed all patches.

Altered patches:
- 950-0064-mfd-Add-Raspberry-Pi-Sense-HAT-core-driver.patch
- 0005-mtd-physmap_of-Move-custom-initialization.patch

Remove upstreamed:
- 0001-pinctrl-gemini-Mask-and-set-properly.patch
- 0002-pinctrl-gemini-Fix-up-TVC-clock-group.patch

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-11-29 09:59:49 +01:00
Manuel Kock
509894cffb lantiq: remove redundant WiFi LED on FRITZ!Box 7320
The led wireless trigger is already set correctly to phy0tpt through the
alias in the device tree.

Signed-off-by: Manuel Kock <github.web@manu.li>
[rephrased commit title]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-11-11 18:17:29 +01:00
Adrian Schmutzler
86a1f52617 lantiq: modify ath9k caldata extraction to reuse caldata.sh
In lantiq, ath9k caldata extraction is implemented to work in two
alternate "modes", the standard one and another one with swapped
byte pairs.

This rearranges the functions so "standard" use is based on the
caldata.sh library, while only a single local function is required
for the special case.

Note that while the parameter for switching between normal and swab
is removed, the size of the caldata is added to the function calls
to stay consistent.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-21 13:28:58 +02:00
Martin Schiller
71e04091a9 lantiq: fix dsl_control status handling.
Commit 7519a36774 ("base-files,procd: add generic service status")
introduced the generic 'status' command which broke the previous
dsl_control status output. To fix this, let's rename the "old" command
to "dslstat".

Fixes: 7519a36774 ("base-files,procd: add generic service status")
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2019-10-15 23:23:08 +02:00
Adrian Schmutzler
48b5d08a48 treewide: use a single ath10k MAC patching function with checksum
While all ath10k eeproms have a checksum field, so far two
functions for patching ath10k MAC address have been present (and
been used).

This merges code to provide a single function ath10k_patch_mac
in caldata.sh, having its name in accordance with ath9k functions.
By doing so, correct MAC patching for current and future ath10k
devices should be ensured.

This patch adds checksum adjustments for several targets on
ath79 and lantiq.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-15 18:13:54 +02:00
Adrian Schmutzler
2c60de0e3f treewide: move MAC address patch functions to common library
This unifies MAC address patch functions and moves them to a
common script. While those were implemented differently for
different targets, they all seem to do the same. The number of
different variants is significantly reduced by this patch.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-14 12:36:02 +02:00
Adrian Schmutzler
5b6a809092 treewide: move calibration data extraction function to library
This moves the almost identical calibration data extraction
functions present multiple times in several targets to a single
library file /lib/functions/caldata.sh.

Functions are renamed with more generic names to merge different
variants that only differ in their names.

Most of the targets used find_mtd_chardev, while some used
find_mtd_part inside the extraction code. To merge them, the more
abundant version with find_mtd_chardev is used in the common code.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[rebase on latest master; add mpc85xx]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-10-13 21:48:58 +02:00
Adrian Schmutzler
c1388a2deb base-files: move xor() from caldata extraction to functions.sh
The xor() function is defined in each of the caldata extraction
scripts for several targets. Move it to functions.sh to reduce
duplicate code.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-13 19:03:57 +02:00
Martin Schiller
c5829788c9 lantiq: add set_port_link feature to xrx200-net driver
This makes it possible to configure the link attributes (aneg, duplex,
speed) of each switch ports.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2019-10-12 23:43:08 +02:00
Adrian Schmutzler
0aab49d234 treewide: fix hex2dec conversion for MAC address checksum offset
If chksum_offset is converted by $(($...)) at the beginning, the
check [ -n "$chksum_offset" ] will always return true, as the
conversion yields "0" for an empty argument, and [ -n "0" ] is
true.

With this patch, the variable is not converted before the check,
but only when it's used in dd.

No conversion is done for use in hexdump, as this can deal with
hex value offsets.

Fixes: b133e466b0 ("treewide: convert WiFi caldata size and offset to hexadecimal")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-09-29 00:46:13 +02:00
Adrian Schmutzler
aea3cab77a lantiq: replace backticks by $(...) and remove useless echo
This replaces deprecated backticks by more versatile $(...) syntax.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[decapitalized patch subject at submitter's request]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-09-29 00:46:13 +02:00
Martin Schiller
315405f36b lantiq-dsl: fix value of FECS counter
Instead of the nFECS value, the nFEC value (the number of corrected code words)
was mistakenly used.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2019-09-19 23:43:27 +02:00
Daniel Golle
ccf3bac6f3 lantiq: add device alias for Alpha ASL56026
BT Openreach ECI VDSL Modem V-2FUb/I is an alias of Alpha ASL56026 as
also stated in the original commit message adding the device
(commit 6254a2028c "lantiq: add support for the Alpha ASL56026").

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-08-22 16:26:05 +02:00
Adrian Schmutzler
0fcab46f97 lantiq: sort device definitions in image/Makefile
This sorts the device definitions in image/Makefile alphabetically
for each subtarget/block.

The order of blocks has not been touched.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-22 16:26:05 +02:00
Moritz Warning
fd66687058 lantiq: split up DEVICE_TITLE
DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT
Uses DEVICE_ALT* variables for alternative vendor/retailer names.

Signed-off-by: Moritz Warning <moritzwarning@web.de>
2019-08-22 12:57:34 +02:00
David Bauer
3032bf7f89 lantiq: unify Fritz!Box LED mappings
This commit unifies the LED mapping of the AVM Fritz!Box routers, which
have a combined Power/DSL LED.

With the stock firmware, the Power LED has the following
characteristics:

 - Blink when DSL sync is being established
 - Solid when DSL sync is present

We can't completely resemble this behavior in OpenWrt. Currently, the
Power LED is completely off, when DSL sync is missing. This is not
really helpful, as a user might have the impression, that he bricked his
device.

Instead, map the Info-LED to the state of the DSL connection.
There is no consistent behavior for the Info-LED in the stock
firmware, as the user can set it's function by himself. The DSL
connection state is one possible option for the Info LED there.

Also use the red Power LED to indicate a running upgrade, in case the
board has a two-color Power LED.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-08-15 14:25:51 +02:00
Adrian Schmutzler
b133e466b0
treewide: convert WiFi caldata size and offset to hexadecimal
This changes size and offset set for WiFi caldata extraction and
MAC address adjustment to hexadecimal notation.

This will be much clearer for the reader when numbers are big, and
will also match the style used for mtd-cal-data in DTS files.

Since dd cannot deal with hexadecimal notation, one has to convert
back to decimal by simple $(($hexnum)).

Acked-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-14 12:36:37 +02:00
Adrian Schmutzler
75bfc393ba treewide: convert MAC address location offsets to hexadecimal
This changes the offsets for the MAC address location in
mtd_get_mac_binary* and mtd_get_mac_text to hexadecimal notation.

This will be much clearer for the reader when numbers are big, and
will also match the style used for mtd-mac-address in DTS files.

(e.g. 0x1006 and 0x5006 are much more useful than 4102 and 20486)

Acked-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-14 12:10:12 +02:00
David Bauer
920abb9b58 lantiq: add led-upgrade alias for Fritz!Box 7412
This adds the led-upgrade alias for the AVM Fritz!Box 7412 to indicate a
running firmware upgrade.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-08-10 16:16:23 +02:00
David Bauer
891a700759 lantiq: enable second VPE on Fritz!Box 7412
The AVM Fritz!Box 7412 does not use the VMMC part of the Lantiq chip but
rather a proprietary solution based on the DECT chip for the FXS ports.

Therefore, the second VPE can be enabled for use with OpenWrt.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-08-10 00:48:01 +02:00
David Bauer
c12947b39e lantiq: correct Fritz!Box 7412 button logic level
The AVM FRITZ!Box 7412 buttons are both active low, which is currently
incorrectly defined in the device-tree.

This leads to the device booting directly into failsafe.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-08-10 00:48:01 +02:00
Koen Vandeputte
c7634180fc kernel: bump 4.19 to 4.19.62
Refreshed all patches.

Remove upstreamed:
- 023-0013-crypto-crypto4xx-fix-AES-CTR-blocksize-value.patch
- 023-0014-crypto-crypto4xx-fix-blocksize-for-cfb-and-ofb.patch
- 023-0015-crypto-crypto4xx-block-ciphers-should-only-accept-co.patch
- 950-0252-staging-bcm2835_camera-Ensure-all-buffers-are-return.patch
- 950-0253-staging-bcm2835-camera-Remove-check-of-the-number-of.patch
- 950-0254-staging-bcm2835-camera-Handle-empty-EOS-buffers-whil.patch
- 950-0489-staging-mmal-vchiq-Replace-spinlock-protecting-conte.patch
- 0021-ARM-dts-gemini-Fix-up-DNS-313-compatible-string.patch
- 049-v4.20-mips-remove-superfluous-check-for-linux.patch
- 100-MIPS-fix-build-on-non-linux-hosts.patch
- 303-MIPS-Fix-bounds-check-virt_addr_valid.patch
- 0002-usb-dwc2-use-a-longer-AHB-idle-timeout-in-dwc2_core_.patch

Altered patches:
- 950-0267-staging-vc04_services-Split-vchiq-mmal-into-a-module.patch
- 700-net-add-qualcomm-mdio-and-phy.patch

Fixes:
- CVE-2019-3846

New symbol:
- AX88796B_PHY

Compile-tested on: cns3xxx, imx6
Runtime-tested on: cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-07-31 16:51:46 +02:00
Johann Neuhauser
c3c3cd5e4a lantiq: use wpad-basic for boards with enough storage
This commit selects wpad-basic for the FRITZ!Box 7312 and 7412 as
wpad-mini is only selected on boards with small flash.

Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
[add short description]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-07-30 00:44:19 +02:00
Rafał Miłecki
8b4bc7abe0 treewide: sysupgrade: don't use $ARGV in platform_do_upgrade()
stage2 passes image path to platform_do_upgrade() as an argument so it
can be simply accessed using $1

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2019-07-17 08:05:38 +02:00
Mathias Kresin
92b768d5f4 lantiq: fix etop compiler warnings
The following warnings are introduced by our own patches:

 lantiq_etop.c:173:1: warning: no semicolon at end of struct or union
 };
 ^
 lantiq_etop.c: In function 'ltq_etop_change_mtu':
 lantiq_etop.c:725:2: warning: ISO C90 forbids mixed declarations and code [-Wdeclaration-after-statement]
  int max = ETH_HLEN + VLAN_HLEN + new_mtu + ETH_FCS_LEN;
  ^~~

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-07-07 11:17:34 +02:00
Petr Štetiar
a4bdae7cf2 lantiq: dts: use generic node names
In DTS Checklist[1] we're now demanding proper generic node names, as
the name of a node should reflect the function of the device and use
generic name for that[2]. Everybody seems to be copy&pasting from DTS
files available in the repository today, so let's unify that naming
there as well and provide proper examples.

1. https://openwrt.org/submitting-patches#dts_checklist
2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation

Signed-off-by: Petr Štetiar <ynezz@true.cz>
[split out treewide patch, integrated P2812HNUF1 rename patch]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[merged key and led changes, use generic node name for flash, wifi and
gpio]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-07-07 11:17:34 +02:00
Mathias Kresin
617622cb3c lantiq: dts: drop falcon clock node
It is pretty ovbious a misuse of the simple-bus binding as no child has
a address.

Luckly the clock node isn't used at all so it is safe to get rid of it.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-07-07 11:17:33 +02:00
Mathias Kresin
627b97f57d lantiq: dts: drop empty falcon devicetree node
Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-07-07 11:17:31 +02:00
Mathias Kresin
0c93c09e6d lantiq: dts: fix unit address mismatch warning
Set a unit address matching the reg property for the EASY98000 ethernet
node.

Fixes a unit mismatch devicetree compiler warning.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-07-07 11:17:28 +02:00
Mathias Kresin
3b215a01bb lantiq: dts: move localbus childs to dts
The localbus childs are highly board specific and need to be part of the
board dts. Otherwise we run into duplicate unit address issues if a
board has something else (NAND) connected to the bus id.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-07-07 11:17:28 +02:00
Mathias Kresin
85debe661e lantiq: dts: fix vmmc unit and register address
The register address is the same for danube und vr9. The register size
is 0x400 byte for danube and 0x300 byte for vr9.

The change doesn't have an impact as the vmmc driver doesn't use the
devicetree and has hardcoded register offsets.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-07-07 11:17:28 +02:00
Mathias Kresin
5eb7e513a5 lantiq: dts: use lower case for hex values
Use only lower case for hex values to keep it consistent.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-07-07 11:17:27 +02:00
Mathias Kresin
fdcfd2b232 lantiq: dts: drop superfluous address and size cells
Fixes the following devicetree compiler warning:

  unnecessary #address-cells/#size-cells without "ranges" or child "reg" property

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-07-07 11:17:27 +02:00
Mathias Kresin
2ec59c173f lantiq: dts: move partitions into partition node
Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-07-07 11:17:27 +02:00
Mathias Kresin
7685ed59c5 lantiq: dts: add missing size and address cells
Add size and address cells where missing to fix the following devicetree
compiler warning:

  Warning (avoid_default_addr_size): Relying on default #address-cells value
  Warning (avoid_default_addr_size): Relying on default #size-cells value

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-07-07 11:17:27 +02:00
Mathias Kresin
e55827b7a5 lantiq: dts: fix size cells
SPI nodes only need an address and no size. Drop the size everywhere.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-07-07 11:17:27 +02:00
Mathias Kresin
35e45b742d lantiq: dts: fix malformed unit addresses
Fixes:

   Warning (unit_address_format): unit name should not have leading "0x"

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-07-07 11:17:27 +02:00
Mathias Kresin
fcac34d01d lantiq: dts: drop superfluous unit address
The cpu temperature driver has the register offset hardcode and doesn't
need a reg.

The mdio bus node is only used as a well known name and doesn't need a
reg or unit address.

syscon-reboot doesn't have a unit address or a reg either. The unit name
collides with reset-controller@10 anyway.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-07-07 11:17:27 +02:00
Mathias Kresin
4053dd3f82 lantiq: dts: add reg if unit address is set
Add the reg property if the node has an unit address. Fixes the
following device tree compiler warning:

  Warning (unit_address_vs_reg): node has a unit name, but no reg property

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-07-07 11:17:27 +02:00
Mathias Kresin
df13384c56 lantiq: dts: move memory node to board dts
The memory node is highly board specific and should be only defined in
the board dts.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-07-07 11:17:26 +02:00
Mathias Kresin
cb689f2723 lantiq: drop kernel 4.14 support
The current state of the kernel 4.14 support is in the openwrt-19.07
branch. No need to keep a not default used kernel in this branch.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-07-04 08:29:14 +02:00
Martin Blumenstingl
e6867a5283 lantiq: switch to kernel 4.19
Use kernel 4.19 by default.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2019-07-04 08:29:13 +02:00
Martin Blumenstingl
7305e2057a lantiq: 4.19: fix panic when using the DMA API
With kernel 4.19 the DMA API relies on a struct device to work properly.
Backport upstream patches which passed a struct device instead of NULL
to the DMA API.

Fixes kernel panics during boot.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-07-04 08:29:13 +02:00
Mathias Kresin
961b8efb5b lantiq: 4.19: load PCIe driver after PCI driver
In case a PCI device is physical present, the Lantiq PCI driver need to
be loaded prior to the Lantiq PCIe driver. Otherwise none of them will
work because updating the BAR 0 of a device attached to the PCIe Bus
will fail.

Till kernel commit 9667bb039bf6 ("MIPS: lantiq: remove unnecessary
of_platform_default_populate call"), the Lantiq PCI driver was probed
early in the boot process via plat_of_setup().

Since the mentioned commit, both drivers are probed via
of_platform_default_populate_init() and they are probed according to
their order in the devicetree source file.

If the Lantiq PCI driver is enabled in the devicetree, defer the probing
og the Lantiq PCIe driver till the Lantiq PCI driver is probed. Use the
presence of a PCU bus as indicater for a loaded Lantiq PCI driver.

This way we don't need to shuffle the PCI/PCIe nodes in the devicetree
source file, as they are already (correctly) ordered based on the unit
address.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-07-04 08:29:13 +02:00
Martin Blumenstingl
eb72439dbb lantiq: 4.19: increase usb reset timeouts
With kernel 4.19 dwc2 would not want to initialize due to reset
timeouts, while it worked fine with 4.14.

Increase the reset timeouts to 1 second, as it was used by the old
lantiq ifxhcd usb driver.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-07-04 08:29:13 +02:00
Hauke Mehrtens
f0c740650b lantiq: make patches apply
The following patches are dropped because they are now upstreamed:
- 0002-gpio-stp-xway-Implement-get-callback.patch
  upstreamed with commit 5b9b2b5284f819 ("gpio: stp-xway: Implement get
  callback")
- 0027-01-net-phy-intel-xway-add-VR9-version-number.patch
  upstreamed with commit 5b73d9955fb4b0 ("net: phy: intel-xway: add VR9
  version number")
- 0027-02-net-phy-intel-xway-add-VR9-v1.1-phy-ids.patch
  upstreamed with commit f452518c982e57 ("net: phy: intel-xway: add VR9
  v1.1 phy ids")

The following patches were updated:
- 0018-MTD-nand-lots-of-xrx200-fixes.patch
  the mainline driver now resides in drivers/mtd/nand/raw/xway_nand.c
  (instead of drivers/mtd/nand/xway_nand.c)
- 0025-NET-MIPS-lantiq-adds-xrx200-net.patch
  the DMA API now requires a valid device to be passed to all operations
- 0028-NET-lantiq-various-etop-fixes.patch
  the DMA API now requires a valid device to be passed to all operations

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-07-04 08:29:13 +02:00
Hauke Mehrtens
eee1b34ce6 lantiq: copy target to kernel 4.19
This just copies the files from the kernel 4.14 specific folders into
the kernel 4.19 specific folder, no changes are done to the files in
this commit.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-07-04 08:29:13 +02:00