For this particualar device we get random MAC's for Wifi on each (re-)boot.
This is because art partition/pre caldata do not contain valid MAC addresses.
As we have now a new/better approach with ath11k_patch_mac we can use it for
this device too.
I'm using this approach for like two weeks and its working flawlessly.
Signed-off-by: Ulrich Stark <pwned-pixel@posteo.de>
qualcommax: IPQ807x: ZyXEL NBG7815: Fix random Wifi MAC
Changing order to 3/phy0/5G-1, 2/phy1/2G, 4/phy2/5G-2.
Signed-off-by: Ulrich Stark <pwned-pixel@posteo.de>
Enable USB 3.0 controller, disable USB 2.0 controller.
The USB 2.0 port on the AP-303H is actually connected to the USB 3.0
controller's HS phy. Enable the HS phy only, since the SS lanes are not
brought out to the connector.
Signed-off-by: Ryan Salsbury <ryanrs@gmail.com>
Use NVMEM to assign "factory sticker" MAC address to WAN ethernet
interface. Set LAN address to sticker + 1.
Signed-off-by: Ryan Salsbury <ryanrs@gmail.com>
Importing pending patch "net: dsa: mt7530: move MT753X_MTRAP operations
for MT7530" broke WAN connectivity on most MT7621 which use PHY-muxing
to hook up either port 0 or port 4 to GMAC1.
Remove it for now until the author submits a fixed version.
Fixes: https://github.com/openwrt/openwrt/issues/15279
Fixes: https://github.com/openwrt/openwrt/issues/15273
Fixes: d40691a5fb ("generic: 6.1, 6.6: mt7530: import pending patches")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The backports introduced in commit d40756563c ("kernel: backport
phylink changes from mainline Linux") broke the mv88e6xxx DSA driver.
A backport to fix this was added to the kirkwood target, but as it is
used in multiple targets, and there's a kmod package for it, the fix
should be in generic backports.
This fixes the switch on the WatchGuard Firebox M300 when running the
6.1 testing kernel.
There is no need to backport the fix for the 6.6 kernel, as it was
included in 6.6.5.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Set DEVICE_DTS_DIR to /qcom by default instead of limiting it to
TESTING_KERNEL since we moved 6.6 to default version.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Set DEVICE_DTS_DIR to /qcom by default instead of limiting it to
TESTING_KERNEL since we moved 6.6 to default version.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
For packets not belonging to a local socket, use fraglist GRO instead of
regular GRO. This make segmenting packets very cheap and avoids the need for
selectively disabling GRO
Signed-off-by: Felix Fietkau <nbd@nbd.name>
For the ARM arch on 6.6, DTS files are moved into their vendor directories,
mimicking arm64. Reflect this in the image Makefile.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
This is an automatically generated commit which aids following Kernel patch history,
as git will see the move and copy as a rename thus defeating the purpose.
See: https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
for the original discussion.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Now that 6.6 is the default, remove the 6.1 config and the hack that
was required for the arm32 DTS dir change.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
In commit 6a8b831593 ("mpc85xx: p1010: change wrapper address of
simple image devices"), we adjusted the wrapper address in the recipe
code for all mpc85xx simpleimage devices, including the Extreme
Networks WS-AP3825i. However, we did not also adjust the
KERNEL_LOADADDR and KERNEL_ENTRY config values for this board. This
broke the simpleimage wrapper loader, causing GitHub issue #15237.
Adjust those config values so we go back to pointing at the right
address. We don't exactly need the memory, but it's also not exactly a
punishment in this case.
Run-tested on a ws-ap3825i.
Fixes: commit 6a8b831593 ("mpc85xx: p1010: change wrapper address of
simple image devices")
Tested-by: Martin Kennedy <hurricos@gmail.com>
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
The compatible string for the MediaTek MT7988 SoC ended up being
'mediatek,mt7988a' instead of 'mediatek,mt7988' in the now upstream
dtsi. Adapt the cpufreq driver so support for frequency scaling is
again usable.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
net: dsa: mt7530: explain exposing MDIO bus of MT7531AE better
net: dsa: mt7530: do not pass port variable to mt7531_rgmii_setup()
net: dsa: mt7530: use priv->ds->num_ports instead of MT7530_NUM_PORTS
net: dsa: mt7530: get rid of mac_port_validate member of mt753x_info
net: dsa: mt7530: refactor MT7530_PMEEECR_P()
net: dsa: mt7530: get rid of function sanity check
net: dsa: mt7530: define MAC speed capabilities per switch model
net: dsa: mt7530: return mt7530_setup_mdio & mt7531_setup_common on error
net: dsa: mt7530: move MT753X_MTRAP operations for MT7530
net: dsa: mt7530: refactor MT7530_HWTRAP and MT7530_MHWTRAP
net: dsa: mt7530: refactor MT7530_MFC and MT7531_CFC, add MT7531_QRY_FFP
net: dsa: mt7530: rename mt753x_bpdu_port_fw enum to mt753x_to_cpu_fw
net: dsa: mt7530: rename p5_intf_sel and use only for MT7530 switch
net: dsa: mt7530: refactor MT7530_PMCR_P()
net: dsa: mt7530: disable EEE abilities on failure on MT7531 and MT7988
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Import patches for the MT7530 DSA driver from net-next tree:
cae425cb43fe net: dsa: allow DSA switch drivers to provide their own phylink mac ops
dd0c9855b413 net: dsa: introduce dsa_phylink_to_port()
7c5e37d7ee78 net: dsa: mt7530: simplify core operations
868ff5f4944a net: dsa: mt7530-mdio: read PHY address of switch from device tree
2c606d138518 net: dsa: mt7530: fix port mirroring for MT7988 SoC switch
d59cf049c837 net: dsa: mt7530: fix mirroring frames received on local port
62d6d91db98a net: dsa: mt7530: provide own phylink MAC operations
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
For all boards currently working with the mt7530 DSA driver we can
be sure that the address of the switch on the MDIO bus is 31 --
simply because that address is hard-coded in the driver and the
address from the Device Tree is being ignore.
An upcoming patch will add support for MT753x ICs which are programmed
to addresses different from 0x1f using bootstrap pins. As a result the
address from the Device Tree will then be taken into account, which
will break currently working boards which got the address set to
anything else than 31.
While at it also unify the syntax in Device Tree to always us a decimal
value for the 'reg' property.
* mt7622-buffalo-wsr-3200ax4s.dts
Cosmetic change 'reg = <0x1f>' -> 'reg = <31>'
* mt7622-dlink-eagle-pro-ai-ax3200-a1.dtsi
Wrong address: 0 -> 31
* mt7622-elecom-wrc-x3200gst3.dts
Wrong address: 0 -> 31
* mt7622-linksys-e8450.dtsi
Wrong address: 0 -> 31
* mt7622-ruijie-rg-ew3200.dtsi
Wrong address: 0 -> 31
* mt7622-xiaomi-redmi-router-ax6s.dts
Wrong address: 0 -> 31
* mt7629-iptime-a6004mx.dts
Wrong address: 2 -> 31
* mt7981b-zbtlink-zbt-z8102ax.dts
Cosmetic change 'reg = <0x1f>' -> 'reg = <31>'
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The Upstream Linux community has discontinued support for the target.
Maintaining support for it downstream would require too much effort.
Moreover, it seems that the supported hardware is no longer deemed worthy
of it.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Use 'mediatek,mt7988a' instead of 'mediatek,mt7988' as compatible
string to be in-sync with upstream and no longer break the cpufreq
driver which was also kept in sync with upstream.
Fixes: 56dd6b473b ("mediatek: sync cpufreq support with changed compatible string")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Kernel 6.6 checks for orphan sections and prints a warning about them,
which in turn will make CI fails as we have Werror enabled there.
Issue is that cache-v7-min.S produces .init.text section which is an
orphan section since it is not being handled by the vmlinux.lds.S linker
script.
So, lets put the generated .init.text section under .text.
Fixes: f0d8ce4f48 ("bcm53xx: add testing support for kernel 6.6")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use ath11k_patch_mac and ath11k_set_macflag functions for RAX120v2 (pre-caldata does not contain valid MAC addresses)
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Use ath11k_patch_mac, ath11k_remove_regdomain and ath11k_set_macflag functions for MX4200
(only v2 variant requires MAC patching)
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Spectrum SAX1V1K is a AX WIFI router with 3 1G and 1 2.5G ports.
The router is provided to Spectrum customers.
It is OEM of Askey RT5010W
https://forum.openwrt.org/t/spectrum-sax1v1k-askey-rt5010w-openwrt-support/149923
It continues the original work by @MeisterLone to get this device supported.
Specifications:
```
• CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
• RAM: 2048MB of DDR3
• Storage: 1024MB eMMC
• Ethernet: 3x 1G RJ45 ports (QCA8075) + 1 2.5G Port (QCA8081)
• WLAN:
• 2.4GHz: Qualcomm QCN5024 4x4 802.11b/g/n/ax 1174 Mbps PHY rate
• 5GHz: Qualcomm QCN5054 4x4 802.11a/b/g/n/ac/ax 2402 PHY rate
• LED: 1 gpio-controlled dual color led (blue/red)
• Buttons: 1x reset
• Power: 12V DC jack
```
Notes:
```
• This commit adds only single partition support, that means
sysupgrade is upgrading the current rootfs partition.
• Installation can be done by serial connection only.
• A poulated serial header is onboard
https://forum.openwrt.org/t/spectrum-sax1v1k-askey-rt5010w-openwrt-support/149923/6
• RX/TX is working, u-boot bootwait is active, secure boot is enabled.
```
Installation Instructions:
**Most part of the installation is performed from an initramfs image.**
Boot initramfs : Using serial connection
1. Boot up the device and wait till it displays "VERIFY_IB: Success. verify IB ok"
2. Once that message appears,
login with username 'root'
password serial number of your router in uppercase.
3. Use vi to paste the 'open.sh' script from @MeisterLone github on your device
https://github.com/MeisterLone/Askey-RT5010W-D187-REV6/blob/master/Patch/open.sh
4. chmod 755 open.sh
5. ./open.sh
6. Set your ip to 192.168.0.1
7. Run a TFTP server and host the initramfs image on the TFTP server and name it "recovery.img"
8. Reboot device. On boot it will try TFTP.
Install OpenWrt from initramfs image:
1. Use SCP (or other way) to transfer OpenWrt factory image
2. Connect to device using SSH (on a LAN port)
3. Flash firmware: sysupgrade
# sysupgrade -n -v /tmp/openwrt_sysupgrade.bin
4. Set U-boot env variable: bootcmd
# fw_setenv bootcmd "run fix_uboot; run setup_and_boot"
5. Reboot the device
# reboot
6. Once device is booted, residue of previous firmware will prevent openwrt to work properly.
Factory Reset is MUST required
# Once serial console is displaying to login, hold reset button for 10 sec
7. Now everything should be operational.
Note: this PR adds only single partition support, that means sysupgrade is
upgrading the current rootfs partition
Signed-off-by: Connor Yoon <j_connor@taliaent.com>
Fix broken BoHong bh25q128as patch that used wrong define for kernel
5.15.
Fixes: 4cb814d403 ("generic: 5.15: Make support for BoHong bh25q128as generic")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fixes error in the form of [0]:
drivers/pinctrl/pinctrl-at91.c:1668:12: error: 'at91_gpio_resume' defined but not used [-Werror=unused-function]
1668 | static int at91_gpio_resume(struct device *dev)
| ^~~~~~~~~~~~~~~~
drivers/pinctrl/pinctrl-at91.c:1650:12: error: 'at91_gpio_suspend' defined but not used [-Werror=unused-function]
1650 | static int at91_gpio_suspend(struct device *dev)
| ^~~~~~~~~~~~~~~~~
[0] - https://lore.kernel.org/all/20221215164301.934805-1-arnd@kernel.org/
Signed-off-by: Nick Hainke <vincent@systemli.org>
This is an automatically generated commit which aids following Kernel patch history,
as git will see the move and copy as a rename thus defeating the purpose.
See: https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
for the original discussion.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Fixes no communication with tethered iOS devices in CDC NCM mode.
Freshly booted iOS devices start in legacy mode, but are put into
NCM mode by the official Apple driver.
[1] a2d274c62eFixes: #12566
Tested-by: Georgi Valkov <gvalkov@gmail.com>
Signed-off-by: Foster Snowhill <forst@pen.gy>
Signed-off-by: Georgi Valkov <gvalkov@gmail.com>
[ better reference fixed issue ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Move the patch for BoHong bh25q128as out of ramips to make it
generic. Not including 6.1.y since the mtd subsystem has changed,
and does not need these changes.
Patch was dropped with ramips updating to 6.1, hence we reintroudce it
here for 5.15 generic.
5.15.y functionality was verified on a Wavlink WL-WN586X3 Rev.a.
Signed-off-by: R Maru <deviantmaru@gmail.com>
[ rebase and add extra info in commit description ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport patches for support of generic spi-nor from SFDP data for
kernel 6.1.
Kernel 5.15 have major rework of the info flags and it's not trustable
to backport this amount of changes and expect correct function of it.
All affected patches automatically refreshed using make
target/linux/refresh.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
As preparation for the arm926ej-s support which has a different
load address, move the KERNEL_LOADADDR into the subtargets.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
This is an automatically generated commit which aids following Kernel patch history,
as git will see the move and copy as a rename thus defeating the purpose.
See: https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
for the original discussion.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
This is an automatically generated commit.
During a `git bisect` session, `git bisect --skip` is recommended.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
For the ARM arch on 6.6, DTS files are moved into their vendor directories,
mimicking arm64. Reflect this in the image Makefile.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Add support for kernel 6.1 as testing kernel for qoriq. Refresh config
using `make kernel_oldconfig`.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This is an automatically generated commit which aids following Kernel patch history,
as git will see the move and copy as a rename thus defeating the purpose.
See: https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
for the original discussion.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
It's the A13-based Olinuxino Micro which has only wireless interfaces. The
A20-based board is a fully-fledged one which has an ethernet interface.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
This device supports channel ranges 36-64 and 100-165, just like
others based on the same reference design, but its current DTS is
unnecessarily restricting these ranges to 36-48 and 149-165.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
In preparation for supporting kernel 6.6, where the DTS files are grouped into
vendors - similarly to what arm64 has been doing all along -, update the
SUNXI_DTS var of this board to prepend it with SUNXI_DTS_DIR.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Kernel 6.1.83 allows to select CONFIG_GPIO_VF610, deactivate it by
default.
This fixes compilation of the armsr/armv8 target.
Fixes: 2ad898e091 ("kernel: bump 6.1 to 6.1.83")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds support for the A1 hardware revision of the DIR-3040.
It is an exact copy of the DIR-3060 save for some cosmetic changes to the housing.
Even going so far as having the same FCC ID.
Hardware specification:
SoC: MediaTek MT7621AT
Flash: Winbond W29N01HVSINA 128MB
RAM: Micron MT41K128M16JT-125 256MB
Ethernet: 5x 10/100/1000 Mbps
WiFi1: MT7615DN 2.4GHz N 2x2:2
WiFi2: MT7615DN 5GHz AC 2x2:2
WiFi3: MT7615N 5GHz AC 4x4:4
Button: WPS, Reset
Flash instructions:
OpenWrt can be installed via D-Link Recovery GUI:
NOTE: Seems to only work in Firefox on Windows.
Tried with Chrome on Windows, Firefox in Linux, and Chromium in Linux.
None of these other browsers worked.
1. Push and hold reset button (on the bottom of the device) until power led
starts flashing (about 10 secs or so) while plugging in the power cable.
2. Give it ~30 seconds, to boot the recovery mode GUI
3. Connect your client computer to LAN1 of the device
4. Set your client IP address manually to 192.168.0.2 / 255.255.255.0.
5. Call the recovery page for the device at http://192.168.0.1/
6. Use the provided emergency web GUI to upload and flash a new firmware to the device
Thanks to @Lucky1openwrt and @iivailo for creating the DIR-3060 DTS file and related changes,
so it was possible for me to adapt them to the DIR-3040, build images,
test and fix minor issues.
MAC Addresses:
| use | address | example |
| --- | --- | --- |
| LAN | label | f4:*:61 |
| WAN | label + 4 | f4:*:65 |
| WI1/2g | label + 2 | f4:*:63 |
| WI1/5g | label + 1 | f4:*:62 |
| WI2/5g | label + 3 | f4:*:64 |
The label MAC address was found in Factory, 0xe000
Checklist:
✓ nand
✓ ethernet
✓ button
✓ wifi2g
✓ wifi5g
✓ wifi5g
✓ mac
✓ led
Signed-off-by: Vince McKinsey <vincemckinsey@gmail.com>
On IIJ SA-W2, some multiple LEDs have no "function" property and only
"color" property is available for the newer binding of LED on Linux
Kernel.
9d93b6d091 ("mvebu: drop redundant label with new LED color/function
format") removes "label" property from LEDs, then, multiple "<color>:"
(ex.: "green:"/"red:") will be appeared and renamed to "<color>:_<num>"
(ex.: "green:_1", "green:_2", ...) by kernel.
log:
[ 1.911118] leds-gpio leds: Led green: renamed to green:_1 due to name collision
[ 1.918600] leds-gpio leds: Led red: renamed to red:_1 due to name collision
[ 1.925727] leds-gpio leds: Led green: renamed to green:_2 due to name collision
[ 1.933202] leds-gpio leds: Led red: renamed to red:_2 due to name collision
[ 1.940321] leds-gpio leds: Led green: renamed to green:_3 due to name collision
[ 1.947797] leds-gpio leds: Led red: renamed to red:_3 due to name collision
[ 1.954939] leds-gpio leds: Led green: renamed to green:_4 due to name collision
[ 1.962456] leds-gpio leds: Led green: renamed to green:_5 due to name collision
/sys/class/leds:
root@OpenWrt:/# ls /sys/class/leds/
green: green:_3 green:status red:_2
green:_1 green:_4 red: red:_3
green:_2 green:_5 red:_1 red:status
Fix this issue by adding missing "function" (and "function-enumerator")
property to those LEDs on IIJ SA-W2.
Fixes: 9d93b6d091 ("mvebu: drop redundant label with new LED color/function format")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
On Fortinet FortiGate 30E/50E, some multiple LEDs have no "function"
property and only "color" property is available for the new binding of
LED on Linux Kernel.
9d93b6d091 ("mvebu: drop redundant label with new LED color/function
format") removes "label" property from LEDs, then, multiple "<color>:"
(ex.: "green:"/"red:"/"amber:") will be appeared as LED names and
renamed to "<color>:_<num>" (ex.: "green:_1", "green:_2", ...) by
kernel.
log:
[ 12.425170] leds-gpio gpio-leds: Led green: renamed to green:_1 due to name collision
[ 12.520390] leds-gpio gpio-leds: Led amber: renamed to amber:_1 due to name collision
[ 12.614931] leds-gpio gpio-leds: Led green: renamed to green:_2 due to name collision
[ 12.709895] leds-gpio gpio-leds: Led green: renamed to green:_3 due to name collision
[ 12.804439] leds-gpio gpio-leds: Led amber: renamed to amber:_2 due to name collision
[ 12.898969] leds-gpio gpio-leds: Led green: renamed to green:_4 due to name collision
[ 12.993504] leds-gpio gpio-leds: Led amber: renamed to amber:_3 due to name collision
[ 13.088033] leds-gpio gpio-leds: Led green: renamed to green:_5 due to name collision
[ 13.182570] leds-gpio gpio-leds: Led green: renamed to green:_6 due to name collision
[ 13.277103] leds-gpio gpio-leds: Led amber: renamed to amber:_4 due to name collision
[ 13.371636] leds-gpio gpio-leds: Led green: renamed to green:_7 due to name collision
/sys/class/leds:
root@OpenWrt:/# ls /sys/class/leds/
amber: amber:_4 green:_2 green:_6 red:alarm
amber:_1 amber:alarm green:_3 green:_7 red:status
amber:_2 green: green:_4 green:status
amber:_3 green:_1 green:_5 red:
Fix this issue by adding missing "function" (and "function-enumerator")
property those to LEDs on Fortinet FortiGate devices.
Note: there is no appropriate function for "ha" LEDs in
dt-bindings/leds/common.h, so use the hardcoded string for them instead.
Fixes: 9d93b6d091 ("mvebu: drop redundant label with new LED color/function format")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Add pending patches to add LED_FUNCTION_MOBILE and LED_FUNCTION_SPEED_*
definitions for Fortinet FortiGate devices and IIJ SA-W2.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Specifications:
Qualcomm/Atheros QCA9531
2x 10/100 Mbps Ethernet, with 48v PoE
2T2R 2.4 GHz, 802.11b/g/n
128MB RAM
16MB SPI Flash
4x LED (Always On Power, LAN, WAN, WLAN)
Flashing instructions:
The original firmware is based on OpenWrt, so flashing the sysupgrade image over the factory firmware is sufficient.
The bootloader has a built-in recovery web-ui. This is the method I used to flash OpenWrt. You can get to the recovery web-ui by holding down the reset button for a few seconds (~5s) while pluggin in the router. The LEDs should start blinking fast and the router should be available on 192.168.1.1 for the recovery.
Tested: Reset button, WAN LED, LAN LED, Power LED (always on, not much to test), WLAN LED, MAC addresses (same as factory firmware).
Signed-off-by: Felix Golatofski <git@xdfr.de>
This reordering was done using these commands:
./scripts/kconfig.pl '+' target/linux/generic/config-6.1 /dev/null > target/linux/generic/config-6.1-new
mv target/linux/generic/config-6.1-new target/linux/generic/config-6.1
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Change the RGB indicator LED color for the running state from green to
blue. There are various reasons for this change:
- In stock firmware, green means internet connection is up, red means it
is down, and blue means indeterminate. To track stock behavior as
closely as possible, OpenWrt should indicate blue by default.
- In the current 23.x OpenWrt releases for this router, the led glows
blue all the time -not green- because the bootloader sets it blue
and there is an OpenWrt bug that makes it unable to control the LED.
The bug is fixed in master, so without this commit there would be an
unexpected change of behavior for this device in the next release.
- The ports other closely related Linksys devices (such as EA8300 and
MR8300) get this right and use blue for the running state.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
The RGB LED should glow green in the 'running' state, but it
was glowing cyan because the blue component defaulted to 'on'.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
The upstream solution to define the MDIO bus in DT is a bit
more strict than our previous downstream solution doing the same thing
and now requires switch PHYs to be referenced in DT as well.
Arınç Ünal told us in #15141:
"With [the now upstream patch written by him which we backported], the
switch MDIO bus won't be assigned to ds->user_mii_bus when the switch
MDIO bus is defined on the device tree anymore. This was not the case
with the downstream patch.
When ds->user_mii_bus is populated, DSA will 1:1 map the port with
PHY. Meaning port with address 1 will be mapped to PHY with address 1.
Because that ds->user_mii_bus is not populated when the switch MDIO
bus is defined on the device tree, on every port node, the PHY address
must be supplied by the phy-handle property."
Add those phy-handles to affected devices' DT.
Fixes: 4354b34f6f ("generic: 6.6: sync mt7530 DSA driver with upstream")
Fixes: 401a6ccfaf ("generic: 6.1: sync mt7530 DSA driver with upstream")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
TP-Link EC220-G5 v2 is a dual band router with 4 GbE ports
Advertised as AC1200 for its 867Mbps (2x2) 5GHz band
and 300 Mbps (2x2) 2.4GHz band.
Specs:
- SoC: MediaTek MT7620A
- Ethernet: 4x GbE ports (Realtek RTL8367S)
- Wireless 2.4GHz: MediaTek MT7620A
- Wireless 5GHz: MediaTek MT7612E
- RAM: 64MiB
- ROM: 8MiB (W25Q64BV)
- 2 Buttons (WPS and reset)
- 7 LEDs
Flash instructions via serial console:
1. Rename the factory.bin to to test.bin
2. start a TFTP server from IP address 192.168.0.225 and serve the image named test.bin
3. connect your device to the LAN port
4. power up the router and press 4 on the console to stop the boot process.
5. enter the following commands on the router console
tftp 0x80060000 test.bin
erase tplink 0x20000 0x7a0000
cp.b 0x80060000 0x20000 0x7a0000
reset
Flash instructions via TFTP:
1. Update orginal firmware of the router to the latest one.
2. Rename openwrt-ramips-mt7620-tplink_ec220-g5-v2-squashfs-tftp-recovery.bin to tp_recovery.bin
3. Change computer IP to 192.168.0.66
4. Run TFTP serwer
5. Start the router with the reset button pressed, the file will be automatically downloaded and after a while the router will restart.
6. After updating, set your computer's IP to DHCP
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Change the name mt7620a_tplink_archer.dtsi to mt7620a_tplink_8m.dtsi because it will also be a base for TP-Link non-Archer routers.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
The function introduced in commit 7cbfe5654d is named
filter_port_list_reverse, not filter_port_list_reversed.
Fixes the following error on hpe,1920-8g-poe-65w and
hpe,1920-8g-poe-180w.
/bin/board_detect: /etc/board.d/02_network: line 84: filter_port_list_reversed: not found
Fixes: 7cbfe5654d ("realtek: move port filtering out of uci_set_poe()")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Sander Vanheule <sander@svanheule.net>
Fix also some Chinese GB18030 -> UTF-8 encoding problems
(translated the Chinese strings to English):
修改 -> modification
port8~port10的设置在另外一个register ->
port8~port10 setup is done in a separate register
You are in the correct (UTF-8) encoding when you see:
* $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
e.g. week 3, 08 third month, 2017
But not if you see:
* $Date: 2017-03-08 15:13:58 +0800 (閫变笁, 08 涓夋湀 2017) $
rtl8367c/rtl8367c_asicdrv_lut.c should be read as UTF-8, despite having
some earlier Chinese text lost to GB18030 encoding.
Improves indexing and searches
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
We have defaulted to 6.6 for a while so its time to completely drop 6.1
so new devices dont have to include patches for 6.1.
Signed-off-by: Robert Marko <robimarko@gmail.com>
HW specifications:
* Mediatek MT7981A
* 256MB SPI-NAND
* 512MB DRAM
* Uplink: 1 x 10/100/1000Base-T Ethernet, Auto MDIX, RJ-45 with 802.3at
PoE (Built-in GBe PHY)
* LAN: 1 x 10/100/1000Base-T Ethernet, Auto MDIX, RJ-45 (Airoha EN8801SC)
* 1 Tricolor LED
* Reset button
* 12V/2.0A DC input
Installation:
Board comes with OpenWifi/TIP which is OpenWrt based, so sysupgrade can
be used directly over SSH.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
