HC5661A:
- Fix pinctrl
- Fix image size (15808k)
- Use switch trigger for WAN LED
Both:
- Use tpt LED trigger for wireless
- Explicitly disable USB nodes
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
HiWiFi has several MT7628AN routers which have similar specs
Add HC5X61A.dtsi to include them, like HC5X61.dtsi (for MT7620A)
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
There's an empty case in 02_network introduced by last commit. Drop it.
Fixes: ee650ba46c ("ramips: remove needless setting of lan_mac to eth0 in 02_network")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This removes superfluous lines like
lan_mac=$(cat /sys/class/net/eth0/address)
Since lan_mac only sets the MAC address for eth0.1, these lines
can be safely removed as the address will be inherited from eth0
anyway.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The vast majority of devices labels "factory" partition with lower
case. Convert the small fraction with capital letter to that and
merge another case in 02_network.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This just merges some duplicate definitions and consolidates lines.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com> [merge duplicated
cases for phicomm k2p]
This cosmetical patch is just meant to make comparing/checking
IMAGE_SIZE values easier.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
There are frequent examples of the ralink_default_fw_size_xxx
variables being used to "roughly" set flash size without caring
about the actual size of the firmware partition.
To discourage this behavior, this patch removes the variables and
just sets IMAGE_SIZE by its numeric value for each target.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Currently, ramips target defines 0x7b0000 as default IMAGE_SIZE
for all devices in ramips target, i.e. this will be set if a
device does not specify IMAGE_SIZE itself.
From 92 devices using that default due to a "missing" IMAGE_SIZE,
14 were incorrect by a small amount (i.e. still "8M" flash) and
12 were completely off ("16M", "4M", ...).
This patch thus removes the _default_ IMAGE_SIZE and defines
IMAGE_SIZE for each device individually. This should indicate to
people supporting new devices that this parameter has to be cared
about.
For the present code, this patch is cosmetical.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This fixes IMAGE_SIZE for all devices based on the partition size
given in DTS:
DEVICE *.MK *.DTS VERDICT
airlink101_ar670w (4M) 0x3c0000 wrong
airlink101_ar725w - 0x3B0000 wrong
asus_rt-n15 (4M) 0x3b0000
belkin_f5d8235-v1 7744k 0x7b0000 wrong
buffalo_wli-tx4-ag300n (4M) 0x3b0000
buffalo_wzr-agl300nh (4M) 0x3b0000
dlink_dap-1522-a1 3801088 0x3a0000
ralink_v11st-fe (4M) 0x003b0000
asus_rt-n56u - 0x007b0000 default
belkin_f9k1109v1 7224k 0x7a0000 wrong
dlink_dir-645 - 0x7b0000 default
edimax_br-6475nd 7744k 0x00790000
loewe_wmdr-143n - 0x7b0000 default
omnima_hpm 16064k 0x00fb0000
samsung_cy-swr1100 - 0x7b0000 default
sitecom_wlr-6000 7244k 0x713000
trendnet_tew-691gr - 0x007b0000 default
trendnet_tew-692gr - 0x007b0000 default
No verdict means that the device is correctly set.
Legend:
( ): Value is set via ralink_default_fw_size_xxM
[ ]: Value is derived from parent definition
- : Value is not set and derived from default definition
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In ramips, there are the following predefined values for IMAGE_SIZE
ralink_default_fw_size_4M 3866624 3776k 0x3B0000
ralink_default_fw_size_8M 8060928 7872k 0x7B0000
ralink_default_fw_size_16M 16121856 15744k 0xF60000
ralink_default_fw_size_32M 33226752 32448k 0x1FB0000
Out of those, the "16M" value is obviously odd, as it provides more
room for the remaining partitions than the tree others.
Of the devices in all subtargets, there are actually > 50 that have
a firmware partition with 0xFB0000 size, while only 5 (!) have
0xF60000. From the former, many are set to
ralink_default_fw_size_16M anyway, although it is wrong at the
present point.
Consequently, it makes sense to change ralink_default_fw_size_16M
to 0xFB0000, and to update IMAGE_SIZE for the 5 devices with
0xF60000.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
allnet_all0256n-4m, tenda_w150m and unbranded_wr512-3gn-4m have
their firmware partition set to reg = <0x50000 0x3c8000>.
However, based on the 4MB flash, the size should be 0x3b0000.
After some research in the target's history, it looks like the
changed size has been a mistake when transferring device
partitions from Makefile to DTS in 770b28f146.
This patch changes the named three devices back to 0x3b0000.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Like most mt7621 boards, Phicomm K2P stores LAN/WAN mac addresses
at 0xe000/0xe006 of factory partition.
Phicomm uses lan_mac-1 as wan_mac, while our default case in 02_network
uses lan_mac+1.
Add a special case reading lan/wan mac address for Phicomm K2P.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Now that the mt76 driver supports the MT7615D chip found on these
devices, use it.
Also add the wpad-basic package.
Note: the driver supports operation on both the 2.4 GHz and the
5 GHz bands, but not yet concurrently.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Newifi D1 is shipped with an 8GB microSD card in its SD slot
Without SD driver users would not be able to use it unless manually installed
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
1) nand_do_upgrade() is always called by a target code
2) nand_do_upgrade() starts with calling platform_nand_pre_upgrade()
It means there is no need for the platform_nand_pre_upgrade() callback
at all. All code that was present there could bo moved & simplly called
by a target right before the nand_do_upgrade().
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
TP-Link RE650 v1 is a dual-band AC2600 range extender,
based on MediaTek MT7621A and MT7615E. According to the
wikidevi entry for RE650 this device is identical with
TP-Link RE500 as hardware. This patch supports only RE650.
Hardware specification:
- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 16 MB - Winbond 25Q128FVSG
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART header (J1) - 2:GND, 3:RX, 4:TX
Serial console @ 57600,8n1
Flash instructions:
Upload
openwrt-ramips-mt7621-tplink_re650-v1-squashfs-factory.bin
from the RE650 web interface.
TFTP recovery to stock firmware:
Unfortunately, I can't find an easy way to recover the RE
without opening the device and using modified binaries. The
TFTP upload will only work if selected from u-boot, which
means you have to open the device and attach to the serial
console. The TFTP update procedure does *not* accept the
published vendor firmware binaries. However, it allows to
flash kernel + rootfs binaries, and this works if you have
a backup of the original contents of the flash. It's probably
possible to create special image out of the vendor binaries
and use that as recovery image.
Signed-off-by: Georgi Vlaev <georgi.vlaev@gmail.com>
[re-added variables for kernel header]
Signed-off-by: David Bauer <mail@david-bauer.net>
ELECOM WRC-1167GHBK2-S has a MediaTek MT7615D chip for 2.4/5 GHz
wireless.
A driver package for MT7615 chip is added to OpenWrt in
a0e5ca4f35,
so add preliminary MT7615 chip support for WRC-1167GHBK2-S.
Note: Currently, DBDC mode for MT7615 is not supported in mt76 driver.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
The only step between platform_pre_upgrade() and platform_do_upgrade()
is switching to ramdisk. It should be fine to "mtd erase firmware" from
the later callback and get rid of the first one.
This change wasn't tested on affected target but identical code logic
was verified to work as expected on brcm47xx with initramfs firmware.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
In 2011 (!), network setup for nexaira,bc2 was moved to network
defaults script with a typo so it became b2c:
295e04084c ("ramips: setup bc2 mac addresses from the generic network script")
This patch just removes the useless entry without replacement,
since it seems to have worked for 8 years anyway.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Since mt76x8an ver1 eco2, SDXC pins can be switched to the
following pinmap:
sd_d1 -> PAD_I2S_SDI
sd_d0 -> PAD_I2S_WS
sd_cmd -> PAD_I2S_CLK
sd_d3 -> PAD_I2C_SCLK
sd_d2 -> PAD_I2C_SD
sd_clk -> PAD_GPIO0
sd_wp -> PAD_TXD1
sd_cd -> PAD_RXD1
To use this pinmap, one would need to set ESD_MODE bit (bit 15)
to 1 in GPIO1_MODE and switch other used pads into GPIO mode.
In this mode, we don't need to switch ethernet pins to digital
pad.
Check ESD_MODE bit before applying AGPIO_CFG and use rt_sysc_m32
to set it.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
SoC: MediaTek MT7621AT
RAM: 128M (Winbond W631GG6KB-15)
FLASH: 16MB (Spansion S25FL128SA)
WiFi: MediaTek MT7603EN bgn 2SS
WiFi: MediaTek MT7612EN nac 2SS
BTN: Reset - WPS
LED: - Power
- LAN {1-4}
- WAN
- WiFi 2.4 GHz
- WiFi 5 GHz
- USB
UART: UART is present next to the Power LED.
TX - RX - GND - 3V3 / 57600-8N1
3V3 is the nearest one to the Power LED.
Installation
------------
Via TFTP:
1. Set your computers IP-Address to 192.168.1.75.
2. Power up the Router with the Reset button pressed.
3. Release the Reset button after 5 seconds.
4. Upload OpenWRT sysupgrade image via TFTP:
> tftp -4 -v -m binary 192.168.1.1 -c put <IMAGE>
Via SSH:
Note: User/password for SSH is identical with the one used in the
Web-interface.
1. Complete the initial setup wizard.
2. Activate SSH under "Administration" -> "System".
3. Transfer the OpenWrt sysupgrade image via scp:
> scp owrt.bin admin@192.168.1.1:/tmp
4. Connect via SSH to the router.
> ssh admin@192.168.1.1
5. Write the OpenWrt image to flash.
> mtd-write -i /tmp/owrt.bin -d linux
6. Reboot the router
> reboot
Signed-off-by: David Bauer <mail@david-bauer.net>
This commit fixes a forgotten case in previous commit.
Fixes: 087e14ab59 ("ramips: mt7621: merge two variants of MQmaker WiTi together")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
mt7621 and mt7628 now have the ability to detect memory size
automatically.
Drop memory nodes and let kernel determine memory size.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
mt7621 has the following memory map:
0x0-0x1c000000: lower 448m memory
0x1c000000-0x2000000: peripheral registers
0x20000000-0x2400000: higher 64m memory
detect_memory_region in arch/mips/kernel/setup.c only add the first
memory region and isn't suitable for 512m memory detection because
it may accidentally read the memory area for peripheral registers.
This commit adds memory detection capability for mt7621:
1. add the highmem area when 512m is detected.
2. guard memcmp from accessing peripheral registers:
This only happens when some weird user decided to change
kernel load address to 256m or higher address. Since this
is a quite unusual case, we just skip 512m testing and return
256m as memory size.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Belkin F7C027 is clearly Rt5350 SoC, as shown on internal
photographs filed for FCC approval[1].
[1]: https://fcc.io/K7S/F7C027
Fixes commit 3b0264eddb
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This patch applies sorting to the definitions as whole blocks.
Sorting has been performed fully automatic, line count differences
originate from double empty lines removed.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch is cosmetical:
It only applies sorting based on device names, whereas renames
already took place in earlier patches.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Having converted the target to use device compatible, ramips.sh
is obsolete now.
The only remaining entry for the mt7688 evaluation board seems to
be orphaned.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
As introduced with ath79, DTS files for ramips will now be labelled
soc_vendor_device.dts(i). With this change, DTS files can be
selected automatically without further manual links.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
As introduced with ath79, DTS files for ramips will now be labelled
soc_vendor_device.dts(i). With this change, DTS files can be
selected automatically without further manual links.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This will automatically derive the DTS name as in ath79 and thus
makes specifying DTS for every device obsolete.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
---
This patch only introduces the mechanism and is then followed by
commits with renames and Makefile adjustments per subtarget.
Eventually, those can be all squashed into a single commit or left
as they are to enhance overview.
This will "rename" devices in Makefiles to the pattern used in
DTS compatible. This will systematize naming of devices
enormously.
As device names are used to for default SUPPORTED_DEVICES entries,
we need to adjust the source for /tmp/sysinfo/board_name, too.
So remove relevant entries from base-files/lib/ramips.sh and
use device compatible for that.
Despite that, base-files are updated, too.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Include "Archer" in compatible as it is part of the device name.
Update Makefile device names where necessary to match compatible.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Upstream kernel added support for RAW_APPENDED_DTB on ralink arch
in the following commit:
02564fc89d3d ("ralink: Introduce fw_passed_dtb to arch/mips/ralink")
Use upstream solution and get rid of our OWRTDTB hack.
This commit set DEVICE_DTS to $$(DTS) instead of replacing DTS with
DEVICE_DTS in device profile because DTS variable will be dropped
in later commits.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[Tested on mt7621/mt76x8]
Tested-by: Chuanhong Guo <gch981213@gmail.com>
[Tested on rt305x/mt7620]
Tested-by: INAGAKI Hiroshi <musashino.open@gmail.com>
TP-Link TL-WR841n v14 is a router based on MediaTek MT7628N.
- MediaTek MT7628NN
- 32 MB of RAM
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
Installation:
- copy the
'openwrt-ramips-mt76x8-tl-wr841n-v14-squashfs-tftp-recovery.bin'
file to your tftp server root and rename it to 'tp_recovery.bin'.
- configure your PC running the TFTP server with the static IP address
192.168.0.66/24
- push the reset button and plug in the power connector. Wait until
the orange led starts blinking (~6sec)
Signed-off-by: Alexander Müller <donothingloop@gmail.com>
Signed-off-by: Alexander Couzens <lynxis@fe80.eu> [small modifications gpio-hog]
Similiar to the lantiq target use a dts alias to define the wlan led
instead of static mapping in /etc/board.d/01_leds. Reduce code
duplication.
A device tree must define the alias "led-wlan" similiar to "led-boot".
/ {
aliases {
led-wlan = &led_wlan;
};
[..]
led_wlan: wlan {
label = "tl-wr841n-v14:green:wlan";
gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
};
};
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Hardware specs:
SoC: Mediatek MT7621A
CPU: 4x 880Mhz
Cache: 32 KB I-Cache and 32 KB D-Cach
256 KB L2 Cache (shared by Dual-Core)
RAM: DDR3 512MB 16bits BUS
FLASH: 16MB
Switch: Mediatek Gigabit Switch (1 x LAN, 1 x WAN)
USB: 1x 3.0
PCI: 3x Mini PCIe
GPS: Quectel L70B
BTN: Reset
LED: - Power
- Ethernet
- Wifi
- USB
UART: UART is present as Pads with throughholes on the PCB.
They are located on left side.
3.3V - RX - GND - TX / 57600-8N1
3.3V is the square pad
Installation:
The stock image is a modified openwrt and can be overflashed via
# sysupgrade -F image.bin
Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[removed unused label, formatting]
This fixes lower case AC in the DTS model name.
Fixes: 88f7a29f99 ("ramips: add support for Edimax EW-7476RPC / EW-7478AC")
Reported-by: Cezary Jackiewicz <cezary@eko.one.pl>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This patch fix and enable GELAN port in D-LINK DWR-118-A2.
Tested-by: Richard Toth <trtk1992@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
In some boards is requred to change the ephy mdio base address.
This patch add of property "mediatek,ephy-base-address" in gsw
part, which allows to change ephy base address.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[fixed indentation in header file]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The port initialisation is based on assumption that phy address and
port number is the same. SoC allow different numbers and some board
have it.
Use phy address instead the port number to make sure that correct
addresses are polled.
In situation when only one PHY with address 0x0 is conected to
port 4, autopolling is broken.
This patch make autopolling correct when port number and phy address
are different.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
The phy handling code forces a phy mdio address and the switch port to
which a phy is attached to be the same. Albeit such a configuration is
used for most boards, it isn't for all.
Pass the switch port number to the ethernet phy connect functions, to
ensure the correct list entry is edited and not the list entry that
matches th phys mdio address.
Use the mdio address with mdiobus_get_phy instead of the port number,
to make sure the expected ethernet phy gets connected.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The whole logic in fe_phy_connect() is based on the asumption that mdio
address and switch port id are equal. Albeit it is true for most
boards, it doesn't is for all.
It isn't yet clear which subtargets/boards require the devicetree less
ethernet phy handling. Hence change the code in a way that it doesn't
touch ethernet phys which were early attached and are already handled.
Signed-off-by: Mathias Kresin <dev@kresin.me>
SoC: MediaTek MT7620a @ 580MHz
RAM: 64M (Winbond W9751G6KB-25)
FLASH: 8MB (Macronix)
WiFi: SoC-integrated: MediaTek MT7620a bgn
WiFi: MediaTek MT7612EN nac
Switch: Mediatek MT7530W Gigabit Switch (4 x LAN, 1 x WAN)
USB: Yes 1 x 2.0 (+ 1 x 2.0 unpopulated header)
BTN: Reset/WPS
LED: - Power (white)
- Internet (blue)
- Wifi (blue)
- USB (blue)
UART: UART is present as Pads with throughholes on the PCB. They are
located in the lower right corner (GbE ports facing up)
3.3V - RX - GND - TX / 57600-8N1
3.3V is the square pad
Installation
------------
Update the factory image via the web-interfaces (by default:
http://edimax.setup)
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
[merge conflicts in 01_leds and mt7620.mk, dts whitespace issues]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
SoC: MediaTek MT7620a @ 580MHz
RAM: 64M (Winbond W9751G6KB-25)
FLASH: 8MB (Macronix)
WiFi: SoC-integrated: MediaTek MT7620a bgn
WiFi: MediaTek MT7612EN nac
GbE: 1x (RTL8211E)
BTN: WPS - RFKILL/RF 50%/RF 100% toggle
LED: - Wifi 5g (blue)
- Wifi 2g (blue)
- Crossband (green)
- Power (green)
- WPS (green)
- LAN (Green)
UART: UART is present as Pads with throughholes on the PCB. They are
located next to the switch for the wifi configuration
3.3V - RX - GND - TX / 57600-8N1
3.3V is the square pad
Installation
------------
Update the factory image via the web-interfaces (by default:
192.168.9.2/24).
http://192.168.9.2/index.asp
ramips: add Edimax EW-7478AC
SoC: MediaTek MT7620a @ 580MHz
RAM: 64M (Winbond W9751G6KB-25)
FLASH: 8MB (Macronix)
WiFi: SoC-integrated: MediaTek MT7620a bgn
WiFi: MediaTek MT7612EN nac
GbE: 1x (RTL8211E)
BTN: WPS - RFKILL/RF 50%/RF 100% toggle
LED: - Wifi 5g (blue)
- Wifi 2g (blue)
- Crossband (green)
- Power (green)
- WPS (green)
- LAN (Green)
UART: UART is present as Pads with throughholes on the PCB. They are
located next to the switch for the wifi configuration
3.3V - RX - GND - TX / 57600-8N1
3.3V is the square pad
Installation
------------
Update the factory image via the web-interfaces (by default:
http://edimaxext.setup)
Or push wpa button on power on and send firmware via tftp to 192.168.1.6
The EW-7478AC is identical to the EW-7476RPC, except instead of 2 internal
antennas it has 2 external ones.
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
[merge conflict in 01_leds]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Refreshed all patches.
This bump contains upstream commits which seem to avoid (not properly fix)
the errors as seen in FS#2305 and FS#2297
Altered patches:
- 403-net-mvneta-convert-to-phylink.patch
- 410-sfp-hack-allow-marvell-10G-phy-support-to-use-SFP.patch
Compile-tested on: ar71xx, cns3xxx, imx6, mvebu, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6, x86_64
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
01_leds has several redundant LED-cases. This commit cleans
up the file by merging these cases into shared cases.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
ASUS RP-N53 and Buffalo WHR-600D use RT5592 for 5GHz wireless
After commit 367813b9b1 the driver for RT5592 (rt2800pci)
is not selected by default anymore, which broke their 5GHz wireless
Add it back to device packages
Fixes: 367813b9b1 ("ramips: mt7620: fix dependencies")
Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
Specifications:
- SoC: MT7628DAN (MT7628AN with 64MB built-in RAM)
- Flash: 8M SPI NOR
- Ethernet: 5x 10/100Mbps
- WiFi: 2.4G: MT7628 built-in
5G: MT7612E
- 1x miniPCIe slot for LTE modem (only USB pins connected)
- 1x SIM slot
Flash instruction:
U-boot has a builtin web recovery page:
1. Hold the reset button while powering it up
2. Connect to the ethernet and set an IP in 192.168.1.0/24 range
3. Open your browser and upload firmware through http://192.168.1.1
Note about the LTE modem:
If your router comes with an EC25 module and it doesn't show up
as a QMI device, you should do the following to switch it to QMI
mode:
1. Install kmod-usb-serial-option and a terminal software
(e.g. minicom or screen). All 4 serial ports of the modem
should be available now.
2. Open /dev/ttyUSB3 with the terminal software and type this
AT command: AT+QCFG="usbnet",0
3. Power-cycle the router. You should now get a QMI device
recognized.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Support for D-Link DWR-118 A1 was added before LEDs feature
in mt76x0e driver.
This fixes the 5GHz WiFi LED which was previously inverted.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This ioctl is currently routed through generic interface code.
dev_ioctl
dev_ethtool
__ethtool_get_link_ksettings
phy_ethtool_ioctl
Cc: Felix Fietkau <nbd@nbd.name>
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The R6220 and WNDR3700v5 are identical apart from using NAND/NOR flash and
having a different casing. This adds a new cleaned up R6220.dtsi with the
common bits for both devices. Both devices now have feature parity.
Performed cleanup:
* generic DTS node names
* regulator for usb power
* added missing pinctrl groups
* use switch port instead of VLAN as trigger for WAN LED
Fixes for WNDR3700v5:
* all LEDS work
* correct ethernet MAC addresses
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
- SoC: MediaTek MT7628AN
- Flash: 16MB (Winbond W25Q128JV)
- RAM: 64MB
- Serial: As marked on PCB, 3V3 logic, baudrate is 115200
- Ethernet: 3x 10/100 Mbps (switched, 2x LAN + WAN)
- WIFI0: MT7628AN 2.4GHz 802.11b/g/n
- WIFI1: MT7612EN 5GHz 802.11ac
- Antennas: 4x external (2 per radio), non-detachable
- LEDs: Programmable power-LED (two-colored, yellow/blue)
Non-programmable internet-LED (shows WAN-activity)
- Buttons: Reset
INSTALLATION:
1. Connect to the serial port of the router and power it up.
If you get a prompt asking for boot-mode, go to step 3.
2. Unplug the router after
> Erasing SPI Flash...
> raspi_erase: offs:20000 len:10000
occurs on the serial port. Plug the router back in.
3. At the prompt select option 2 (Load system code then
write to Flash via TFTP.)
4. Enter 192.168.1.1 as the device IP and 192.168.1.2 as the
Server-IP.
5. Connect your computer to LAN1 and assign it as 192.168.1.2/24.
6. Rename the sysupgrade image to test.bin and serve it via TFTP.
7. Enter test.bin on the serial console and press enter.
Signed-off-by: Markus Scheck <markus@mscheck.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[added mt76 compatible]
Cudy WR1200 is an AC1200 AP with 3-port FE and 2 non-detachable antennas
Specifications:
MT7628 (580 MHz)
64 MB of RAM (DDR2)
8 MB of FLASH
2T2R 2.4 GHz (MT7628)
2T2R 5 GHz (MT7612E)
3x 10/100 Mbps Ethernet (2 LAN + 1 WAN)
2x external, non-detachable antennas (5dbi)
UART header on PCB (57600 8n1)
7x LED, 2x button
Known issues:
The Power LED is always ON, probably because it is connected
directly to power.
Flash instructions
------------------
Load the ...-factory.bin image via the stock web interface.
Openwrt upgrade instructions
----------------------------
Use the ...-sysupgrade.bin image for future upgrades.
Revert to stock FW
------------------
Warning! This tutorial will work only with the following OEM FW:
WR1000_EU_92.122.2.4987.201806261618.bin
WR1000_US_92.122.2.4987.201806261609.bin
If in the future these firmwares will not be available anymore,
you have to find the new XOR key.
1) Download the original FW from the Cudy website.
(For example WR1000_EU_92.122.2.4987.201806261618.bin)
2) Remove the header.
dd if="WR1000_EU_92.122.2.4987.201806261618.bin" of="WR1000_EU_92.122.2.4987.201806261618.bin.mod" skip=8 bs=64
3) XOR the new file with the region key.
FOR EU: 7B76741E67594351555042461D625F4545514B1B03050208000603020803000D
FOR US: 7B76741E675943555D5442461D625F454555431F03050208000603060007010C
You can use OpenWrt's tools/firmware-utils/src/xorimage.c tool for this:
xorimage -i WR1000..bin.mod -o stock-firmware.bin -x -p 7B767..
Or, you can use this tool (CHANGE THE XOR KEY ACCORDINGLY!):
https://gchq.github.io/CyberChef/#recipe=XOR(%7B'option':'Hex','string':''%7D,'',false)
4) Check the resulting decrypted image.
Check if bytes from 0x20 to 0x3f are:
4C 69 6E 75 78 20 4B 65 72 6E 65 6C 20 49 6D 61 67 65 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Alternatively, you can use u-boot's tool dumpimage tool to check
if the decryption was successful. It should look like:
# dumpimage -l stock-firmware.bin
Image Name: Linux Kernel Image
Created: Tue Jun 26 10:24:54 2018
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 4406635 Bytes = 4303.35 KiB = 4.20 MiB
Load Address: 80000000
Entry Point: 8000c150
5) Flash it via forced firmware upgrade and don't "Keep Settings"
CLI: sysupgrade -F -n stock-firmware.bin
LuCI: make sure to click on the "Keep settings" checkbox
to disable it. You'll need to do this !TWICE! because
on the first try, LuCI will refuse the image and reset
the "Keep settings" to enable. However a new
"Force upgrade" checkbox will appear as well.
Make sure to do this very carefully!
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[added wifi compatible, spiffed-up the returned to stock instructions]
This uses the existing rules for Sercomm factory images and moves them
to the ramips image Makefile, so they can be used in all subtargets.
The new factory image for WNDR3700v5 can be flashed using nmrpflash.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Specification:
CPU: MT7628 580 MHz. MIPS 24K
RAM: 128 MB
Flash: 32 MB
WIFI: 802.11n/g/b 20/40 MHz
Ethernet: 5 Port ethernet switch
UART: 2x
Flash instruction:
The U-boot is based on Ralink SDK so we can flash the firmware using UART:
1. Configure PC with a static IP address and setup an TFTP server.
2. Put the firmware into the tftp directory.
3. Connect the UART0 line as described on the PCB.
4. Power up the device and press 2, follow the instruction to
set device and tftp server IP address and input the firmware
file name. U-boot will then load the firmware and write it into
the flash.
5. After firmware is started connect via ethernet at 192.168.1.1
Signed-off-by: Liu Yu <f78fk@live.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed dupped subject]
ZBT WE826-E is a dual-SIM version of the ZBT WE826. The router has the
following specifications:
- MT7620A (580 MHz)
- 128MB RAM
- 32MB of flash (SPI NOR)
- 5x 10/100Mbps Ethernet (MT7620A built-in switch)
- 1x microSD slot
- 1x miniPCIe slot (only USB2.0 bus)
- 2x SIM card slots (standard size)
- 1x USB2.0 port
- 1x 2.4GHz wifi (rt2800)
- 10x LEDs (4 GPIO-controlled)
- 1x reset button
The following have been tested and working:
- Ethernet switch
- wifi
- miniPCIe slot
- USB port
- microSD slot
- sysupgrade
- reset button
Installation and recovery:
In order to install OpenWRT the first time or recover the router, you
can use the web-based recovery system. Keep the reset button pressed
during boot and access 192.168.1.1 in your browser when your machine
obtains an IP address. Upload the firmware to start the recovery
process.
How to swap SIMs:
You control which SIM slot to use by writing 0/1 to
/sys/class/gpio/gpio13/value. In order for the change to take effect,
you can either use AT-commands (AT+CFUN) or power-cycle the modem (write
0/1 to /sys/class/gpio/gpio14/value).
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Head Weblink HDRM200 is a dual-sim router based on MT7620A. The detailed
specifications are:
- MT7620A (580MHz)
- 64MB RAM
- 16MB of flash (SPI NOR)
- 6x 10/100Mbps Ethernet (MT7620A built-in switch)
- 1x microSD slot
- 1x miniPCIe slot (only USB2.0 bus). Device is shipped with a SIMCOM
SIM7100E LTE modem.
- 2x SIM slots (standard size)
- 1x USB2.0 port
- 1x 2.4GHz wifi (rt2800)
- 1x 5GHz wifi (mt7612)
- 1x reset button
- 1x WPS button
- 3x GPIO-controllable LEDs
- 1x 10 pin terminal block (RS232, RS485, 4 x GPIO)
Tested:
- Ethernet switch
- Wifi
- USB slot
- SD card slot
- miniPCIe-slot
- sysupgrade
- reset button
Installation instructions:
Installing OpenWRT for the first time requires a bit of work, as the
board does not ship with OpenWRT. In addition, the bootloader
automatically reboots when installing an image over tftp. In order to
install OpenWRT on the HDRM200, you need to do the following:
* Copy the initramfs-image to your tftp-root (default filename is
test.bin) and configure networking accordingly (default server IP is
10.10.10.3, client 10.10.10.123). Start your tftp server.
* Open the board and connect to UART. The pins are exposed and clearly
marked.
* Boot the board and press 1.
* Either use the default filename and client/server IP-addresses, or
specify your own.
The image should now be loaded to memory and board boot. If the router
reboots while the image is loading, you need to try again. Once the
board has booted, copy the sysupgrade-image to the router and run
sysupgrade in order to install OpenWRT to the flash.
Notes:
- You control which SIM slot to use by writing 0/1 to
/sys/class/gpio/gpio0/value. In order for the change to take
effect, you can either use AT-commands (AT+CFUN) or power-cycle the
modem (write 0/1 to /sys/class/gpio/gpio21/value).
- RS485 is available on /dev/ttyS0.
- RS232 is available on /dev/ttyS1.
- The name of the ioX-gpios map to the labels on the casing.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
[fixed whitespace issue and merge conflict in target.mk]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The factory firmware omits the JFFS2 end-marker while flashing via
web-interface. Add a 64k padding after the marker fixes this problem.
When the end-marker is not present, OpenWRT won't save the overlayfs
after initial flash.
Reported-by: Andreas Ziegler <dev@andreas-ziegler.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
MT7620 integrated WMAC does not need RT2x00 PCI driver or firmware
Also corrected kmod-eeprom-93cx6 and kmod-lib-crc-itu-t dependencies
according to original Kconfig and lsmod output
This will remove some unnecessary packages from MT7620 target to
save some space
Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[75 characters per line in the commit message]
It's OEM module with 2*26 pin header, similar to LinkIt Smart 7688 or
Vocore2.
Specification:
CPU: MT7628 580 MHz. MIPS 24K
RAM: 64 MB
Flash: 8 MB
WIFI: 802.11n/g/b 20/40 MHz
USB: 1x Port USB 2.0
Ethernet: 5 Port ethernet switch
UART: 2x
Installation: Use the installed uboot Bootloader. Connect a serial cable
to serialport 0. Turn power on. Choose the option: "Load system code
then write to Flash via TFTP". Choose the local device IP and the TFTP
server IP and the file name of the system image. After if the
Bootloader will copy the image to the local flash.
Notes: The I2C Kernel module work not correctly. You can send and
receive data. But the command i2cdetect doesn’t work. FS#845
Signed-off-by: Eike Feldmann <eike.feldmann@outlook.com>
[commit subject and message touches, DTS whitespace fixes, wifi LED
rename, pinctrl fixes, network settings fixes, lan/wmac mac addresses,
removed i2c kernel modules]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Hardware
--------
SoC: MediaTek MT7628NN
RAM: 64M DDR2 (Etron EM68B16CWQD-25H)
FLASH: 8M (Winbond W25Q64JVSIQ)
LED: Power - WLAN
BTN: Reset
UART: 115200 8N1
TX and RX are labled on the board as pads next to the SoC
Installation via web-interface
------------------------------
1. Visit the web-interface at 192.168.8.1
Note: The ethernet port is by default WAN. So you need to connect to
the router via WiFi
2. Navigate to the Update tab on the left side.
3. Select "Local Update"
4. Upload the OpenWrt sysupgrade image.
Note: Make sure you select not to preserve the configuration.
Installation via U-Boot
-----------------------
1. Hold down the reset button while powering on the device.
Wait for the LED to flash 5 times.
2. Assign yourself a static IPv4 in 192.168.1.0/24
3. Upload the OpenWrt sysupgrade image at 192.168.1.1.
Signed-off-by: David Bauer <mail@david-bauer.net>
Instead of assigning I2C pins as GPIOs by default, leave it up to the
user whether to install kmod-i2c-mt7621 and use them for hardware I2C
instead.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add switch definition for the rtl8367b switch to the DTS/DTSi for
the Belkin F9K1109v1 that was mistakenly omitted from the initial
commit.
Fixes: 017ec068e3 (ramips: add support for Belkin F9K1109v1)
Signed-off-by: Kip Porterfield <kip.porterfield@gmail.com>
Upstream driver has gone through a series of cleanup and was moved
from drivers/staging into drivers/spi. Backport it to replace our
messy driver.
Tested-by: Jörg Schüler-Maroldt <joerg-linux@arcor.de>
[LinkIt Smart 7688, AcSIP AI7688H Wi-Fi module]
Tested-by: Rosen Penev <rosenp@gmail.com>
Tested-by: Tian Xiao bo <peterwillcn@gmail.com>
[Newifi-D2 MediaTek MT7621 ver:1 eco:3]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Enable the USB power for the Netgear R6120. Otherwise, no power is
supplied to an attached USB device.
Signed-off-by: David Bauer <mail@david-bauer.net>
Hardware spec:
CPU: MTK MT7621A
RAM: 256MB
ROM: 16MB SPI Flash
WiFi: MT7603EN + MT7612EN
Button: 2 buttons (reset, wps)
LED: 8 LEDs (Power 2G 5G WPS Internet LAN1 LAN2 USB)
Ethernet: 3 ports, 2 LAN + 1 WAN
Other: USB3.0
Flashing instructions:
Visit the openwrt forum topic for this router:
https://forum.openwrt.org/t/add-openwrt-support-for-youku-yk-l2/34692
to get the bootloader and unlock firmware.
0. upgrade your router with the telnet firmware via the
firmware upgrade page on the webui.
1. telnet 192.168.11.1 from your PC
2. Download the pb-boot-youku_l2-20190317-61b6d33.bin and transfer
it to the /tmp directory of the router.
3. mtd write /tmp/pb-boot-youku_l2-20190317-61b6d33.bin Bootloader
4. turn off the power
5. Push the reset button while turning on the router and
wait until LED start blinking (~10sec.)
6. Connect Ethernet port and goto http://192.168.1.1.
7. Upload the firmware to firmware restore page in webui.
Signed-off-by: Zhao Yu <574249312@qq.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [rewrote the
flashing instructions, fixed author]
This adds the SPDX license identifier for the NETGEAR EX6150. It was
missed when submitting the original patch.
Signed-off-by: David Bauer <mail@david-bauer.net>
The specific flash chip used (W25Q256FVEM) accepts 50MHz for read
requests and higher for others. 104MHz for fast reads. ramips seems to
be limited to 80MHz based on testing with higher values (no speedup).
Based on upstream commit: 97738374a310b9116f9c33832737e517226d3722
time dd if=/dev/mtdblock3 of=/dev/null bs=64k from 42.96s to 7.01s
[test done with backported upstream v4.19 driver[1], for numbers on
stock 4.14 driver please take a look at `ramips: Increase GB-PC2 SPI
frequency to 80MHz` commit message]
1. https://github.com/openwrt/openwrt/pull/1578
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[expanded note about spi driver version]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The flash chip on the board (Spansion S25FL256SAIF00) is rated to
support at least 50MHz for normal read requests according to the
datasheet. 133MHz for fast reads. However, ramips seems to be limited to
80MHz.
>From testing this, higher values do not improve speeds.
time dd if=/dev/mtdblock3 of=/dev/null bs=64k from
42.82s to 14.09s.
boot speed is also faster:
[ 66.884087] procd: - init - vs
[ 48.976049] procd: - init -
Since spi speed was requested:
[ 3.538884] spi-mt7621 1e000b00.spi: sys_freq: 225000000
CPU is 900MHz:
[ 0.000000] CPU Clock: 900MHz
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[fixed commit message by adding missing 0 in the spi-mt7621 clock output]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
SoC: MediaTek MT7621
RAM: 64M (Winbond W9751G6KB-25)
FLASH: 16MB (Macronix MX25L12835F)
WiFi: MediaTek MT7662E bgn 2SS
WiFi: MediaTek MT7662E nac 2SS
BTN: ON/OFF - Reset - WPS - AP/Extender toggle
LED: - Arrow Right (blue)
- Arrow Left (blue)
- WiFi 1 (red/green)
- WiFi 2 (red/green)
- Power (green/amber)
- WPS (Green)
UART: UART is present as Pads on the backside of the PCB. They are
located on the other side of the Ethernet port.
3.3V - GND - TX - RX / 57600-8N1
3.3V is the nearest one to the antenna connectors
Installation
------------
Update the factory image via the Netgear web-interfaces (by default:
192.168.1.250/24).
You can also use the factory image with the nmrpflash tool.
For more information see https://github.com/jclehner/nmrpflash
Signed-off-by: David Bauer <mail@david-bauer.net>
[merge conflict in 02_network, flash@0 node rename, wlan DTS triggers]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Device specification:
- SoC: RT5350F
- CPU Frequency: 360 MHz
- Flash Chip: Winbond 25Q32 (4096 KiB)
- RAM: 32768 KiB
- 5x 10/100 Mbps Ethernet (4x LAN, 1x WAN)
- 1x external, non-detachable antenna
- UART (J1) header on PCB (57800 8n1)
- Wireless: SoC-intergated: 2.4GHz 802.11bgn
- USB: None
- 3x LED, 2x button
Flash instruction:
1. Configure PC with static IP 192.168.1.2/24 and start TFTP server.
2. Rename "openwrt-ramips-rt305x-kn_st-squashfs-sysupgrade.bin"
to "kstart_recovery.bin" and place it in TFTP server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed until power LED start blinking.
4. Router will download file from TFTP server, write it to flash and reboot.
Signed-off-by: Vladimir Kot <vova28rus@gmail.com>
[fixed git commit author and whitespace issues in DTS]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The WIZnet WizFi630S board is in the miniPCIe form factor.
SoC: Mediatek MT7688AN
RAM: 128MB
Flash: 32Mb
WiFi: 2.4GHz
Ethernet: 3x 100Mbit
USB: 1 (USB 2.0)
serial ports: 2 (1x full, 1xlite)
Flash and recovery instructions: Use the factory installed u-boot boot
loader. It is available on UART2 (115200,8,n,1). Then get the
sysupgrade image from a tftp server.
Signed-off-by: Tobias Welz <tw@wiznet.eu>
[whitespace and device name in makefile fixes]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
