Commit Graph

3150 Commits

Author SHA1 Message Date
Leonardo Mörlein
b993b68b6c build: introduce $(MKHASH)
Before this commit, it was assumed that mkhash is in the PATH. While
this was fine for the normal build workflow, this led to some issues if

    make TOPDIR="$(pwd)" -C "$pkgdir" compile

was called manually. In most of the cases, I just saw warnings like this:

    make: Entering directory '/home/.../package/gluon-status-page'
    bash: line 1: mkhash: command not found
    bash: line 1: mkhash: command not found
    bash: line 1: mkhash: command not found
    bash: line 1: mkhash: command not found
    bash: line 1: mkhash: command not found
    bash: line 1: mkhash: command not found
    bash: line 1: mkhash: command not found
    bash: line 1: mkhash: command not found
    [...]

While these were only warnings and the package still compiled sucessfully,
I also observed that some package even fail to build because of this.

After applying this commit, the variable $(MKHASH) is introduced. This
variable points to $(STAGING_DIR_HOST)/bin/mkhash, which is always the
correct path.

Signed-off-by: Leonardo Mörlein <me@irrelefant.net>
2021-05-13 15:13:15 +02:00
Shiji Yang
e57e460dc7 ramips: fix mac addresses of Youku YK1
MAC addresses read from official firmware

        value       location
Wlan    xx 71 de    factory@0x04
Lan     xx 71 dd    factory@0x28
Wan     xx 71 df    factory@0x2e
Label   xx 71 dd    factory@0x28

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[fix sorting in 02_network, redact commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-05-10 14:41:06 +02:00
Adrian Schmutzler
f4940d2229 ramips: use standard naming scheme for Zyxel NR7101 LED nodes
Make naming and DT label consistent with other devices at this
target.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-05-10 14:41:06 +02:00
Bjørn Mork
2449a63208 ramips: mt7621: Add support for ZyXEL NR7101
The ZyXEL NR7101 is an 802.3at PoE powered 5G outdoor (IP68) CPE
with integrated directional 5G/LTE antennas.

Specifications:

 - SoC: MediaTek MT7621AT
 - RAM: 256 MB
 - Flash: 128 MB MB NAND (MX30LF1G18AC)
 - WiFi: MediaTek MT7603E
 - Switch: 1 LAN port (Gigabiti)
 - 5G/LTE: Quectel RG502Q-EA connected by USB3 to SoC
 - SIM: 2 micro-SIM slots under transparent cover
 - Buttons: Reset, WLAN under same cover
 - LEDs: Multicolour green/red/yellow under same cover (visible)
 - Power: 802.3at PoE via LAN port

The device is built as an outdoor ethernet to 5G/LTE bridge or
router. The Wifi interface is intended for installation and/or
temporary management purposes only.

UART Serial:

57600N1
Located on populated 5 pin header J5:

 [o] GND
 [ ] key - no pin
 [o] RX
 [o] TX
 [o] 3.3V Vcc

Remove the SIM/button/LED cover, the WLAN button and 12 screws
holding the back plate and antenna cover together. The GPS antenna
is fixed to the cover, so be careful with the cable.  Remove 4
screws fixing the antenna board to the main board, again being
careful with the cables.

A bluetooth TTL adapter is recommended for permanent console
access, to keep the router water and dustproof. The 3.3V pin is
able to power such an adapter.

MAC addresses:

OpenWrt OEM   Address          Found as
lan     eth2  08:26:97:*:*:BC  Factory 0xe000 (hex), label
wlan0   ra0   08:26:97:*:*:BD  Factory 0x4 (hex)
wwan0   usb0  random

WARNING!!

ISP managed firmware might at any time update itself to a version
where all known workarounds have been disabled.  Never boot an ISP
managed firmware with a SIM in any of the slots if you intend to use
the router with OpenWrt. The bootloader lock can only be disabled with
root access to running firmware. The flash chip is physically
inaccessible without soldering.

Installation from OEM web GUI:

- Log in as "supervisor" on https://172.17.1.1/
- Upload OpenWrt initramfs-recovery.bin image on the
  Maintenance -> Firmware page
- Wait for OpenWrt to boot and ssh to root@192.168.1.1
- (optional) Copy OpenWrt to the recovery partition. See below
- Sysupgrade to the OpenWrt sysupgrade image and reboot

Installation from OEM ssh:

- Log in as "root" on 172.17.1.1 port 22022
- scp OpenWrt initramfs-recovery.bin image to 172.17.1.1:/tmp
- Prepare bootloader config by running:
    nvram setro uboot DebugFlag 0x1
    nvram setro uboot CheckBypass 0
    nvram commit
- Run "mtd_write -w write initramfs-recovery.bin Kernel" and reboot
- Wait for OpenWrt to boot and ssh to root@192.168.1.1
- (optional) Copy OpenWrt to the recovery partition. See below
- Sysupgrade to the OpenWrt sysupgrade image and reboot

Copying OpenWrt to the recovery partition:

- Verify that you are running a working OpenWrt recovery image
  from flash
- ssh to root@192.168.1.1 and run:
    fw_setenv CheckBypass 0
    mtd -r erase Kernel2
- Wait while the bootloader mirrors Image1 to Image2

NOTE: This should only be done after successfully booting the OpenWrt
  recovery image from the primary partition during installation.  Do
  not do this after having sysupgraded OpenWrt!  Reinstalling the
  recovery image on normal upgrades is not required or recommended.

Installation from Z-Loader:

- Halt boot by pressing Escape on console
- Set up a tftp server to serve the OpenWrt initramfs-recovery.bin
  image at 10.10.10.3
- Type "ATNR 1,initramfs-recovery.bin" at the "ZLB>" prompt
- Wait for OpenWrt to boot and ssh to root@192.168.1.1
- Sysupgrade to the OpenWrt sysupgrade image

NOTE: ATNR will write the recovery image to both primary and recovery
  partitions in one go.

Booting from RAM:

- Halt boot by pressing Escape on console
- Type "ATGU" at the "ZLB>" prompt to enter the U-Boot menu
- Press "4" to select "4: Entr boot command line interface."
- Set up a tftp server to serve the OpenWrt initramfs-recovery.bin
  image at 10.10.10.3
- Load it using "tftpboot 0x88000000 initramfs-recovery.bin"
- Boot with "bootm  0x8800017C" to skip the 380 (0x17C) bytes ZyXEL
  header

This method can also be used to RAM boot OEM firmware. The warning
regarding OEM applies!  Never boot an unknown OEM firmware, or any OEM
firmware with a SIM in any slot.

NOTE: U-Boot configuration is incomplete (on some devices?). You may
  have to configure a working mac address before running tftp using
   "setenv eth0addr <mac>"

Unlocking the bootloader:

If you are unebale to halt boot, then the bootloader is locked.

The OEM firmware locks the bootloader on every boot by setting
DebugFlag to 0.  Setting it to 1 is therefore only temporary
when OEM firmware is installed.

- Run "nvram setro uboot DebugFlag 0x1; nvram commit" in OEM firmware
- Run "fw_setenv DebugFlag 0x1" in OpenWrt

  NOTE:
    OpenWrt does this automatically on first boot if necessary

  NOTE2:
    Setting the flag to 0x1 avoids the reset to 0 in known OEM
    versions, but this might change.

  WARNING:
    Writing anything to flash while the bootloader is locked is
    considered extremely risky. Errors might cause a permanent
    brick!

Enabling management access from LAN:

Temporary workaround to allow installing OpenWrt if OEM firmware
has disabled LAN management:

- Connect to console
- Log in as "root"
- Run "iptables -I INPUT -i br0 -j ACCEPT"

Notes on the OEM/bootloader dual partition scheme

The dual partition scheme on this device uses Image2 as a recovery
image only. The device will always boot from Image1, but the
bootloader might copy Image2 to Image1 under specific conditions. This
scheme prevents repurposing of the space occupied by Image2 in any
useful way.

Validation of primary and recovery images is controlled by the
variables CheckBypass, Image1Stable, and Image1Try.

The bootloader sets CheckBypass to 0 and reboots if Image1 fails
validation.

If CheckBypass is 0 and Image1 is invalid then Image2 is copied to
Image1.

If CheckBypass is 0 and Image2 is invalid, then Image1 is copied to
Image2.

If CheckBypass is 1 then all tests are skipped and Image1 is booted
unconditionally.  CheckBypass is set to 1 after each successful
validation of Image1.

Image1Try is incremented if Image1Stable is 0, and Image2 is copied to
Image1 if Image1Try is 3 or larger.  But the bootloader only tests
Image1Try if CheckBypass is 0, which is impossible unless the booted
image sets it to 0 before failing.

The system is therefore not resilient against runtime errors like
failure to mount the rootfs, unless the kernel image sets CheckBypass
to 0 before failing. This is not yet implemented in OpenWrt.

Setting Image1Stable to 1 prevents the bootloader from updating
Image1Try on every boot, saving unnecessary writes to the environment
partition.

Keeping an OpenWrt initramfs recovery as Image2 is recommended
primarily to avoid unwanted OEM firmware boots on failure. Ref the
warning above. It enables console-less recovery in case of some
failures to boot from Image1.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-05-09 09:15:44 +02:00
Ilya Lipnitskiy
89b99e9c1a treewide: consolidate named GPIO patch into hack-5.10
ath79, lantiq, ipq40xx, ramips all use the OpenWrt-specific gpio-export
functionality. Consolidate the patch that adds it under hack-5.10 since
this logic is obviously not target-specific. For those who want to
disable it, unsetting CONFIG_GPIO_SYSFS symbol will disable this code.

Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
2021-05-09 09:15:44 +02:00
Hauke Mehrtens
9ffa2f8193 kernel: Activate FORTIFY_SOURCE for MIPS kernel 5.4
CONFIG_FORTIFY_SOURCE=y is already set in the generic kernel
configuration, but it is not working for MIPS on kernel 5.4, support for
MIPS was only added with kernel 5.5, other architectures like aarch64
support FORTIFY_SOURCE already since some time.

This patch adds support for FORTIFY_SOURCE to MIPS with kernel 5.4,
kernel 5.10 already supports this and needs no changes.

This backports one patch from kernel 5.5 and one fix from 5.8 to make
fortify source also work on our kernel 5.4.

The changes are not compatible with the
306-mips_mem_functions_performance.patch patch which was also removed
with kernel 5.10, probably because of the same problems. I think it is
not needed anyway as the compiler should automatically optimize the
calls to memset(), memcpy() and memmove() even when not explicitly
telling the compiler to use the build in variant.

This increases the size of an uncompressed kernel by less than 1 KB.

Acked-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-04-30 23:51:19 +02:00
Ilya Lipnitskiy
0d6f207230 kernel: backport mtk_soc_eth fixes from v5.13
Fixes logic that leads to this error when booting mt7621 and other
devices that use the mediatek ethernet driver:
  [   23.144378] mtk_soc_eth 1e100000.ethernet: PPE table busy

The rest are mostly moved from pending-5.10 to backport-5.10 with a
couple of cleanups and improvements from upstream.

Refresh patches.

Links:
    https://git.kernel.org/netdev/net-next/c/c5d66587b890
    https://git.kernel.org/netdev/net-next/c/3f57d8c40fea
    https://git.kernel.org/netdev/net-next/c/5196c4178549
    https://git.kernel.org/netdev/net-next/c/787082ab9f7b
    https://git.kernel.org/netdev/net-next/c/c30c4a827390
    https://git.kernel.org/netdev/net-next/c/3630d519d7c3
    https://git.kernel.org/netdev/net-next/c/16ef670789b2
    https://git.kernel.org/netdev/net-next/c/59555a8d0dd3
    https://git.kernel.org/netdev/net-next/c/6b4423b258b9
    https://git.kernel.org/netdev/net-next/c/e9229ffd550b
    https://git.kernel.org/netdev/net-next/c/4e6bf609569c
    https://git.kernel.org/netdev/net-next/c/816ac3e6e67b
    https://git.kernel.org/netdev/net-next/c/16769a8923fa
    https://git.kernel.org/netdev/net-next/c/db2c7b353db3
    https://git.kernel.org/netdev/net-next/c/fa817272c37e
    https://git.kernel.org/netdev/net-next/c/3bc8e0aff23b

Fixes: f07fe36f22 ("kernel: update flow offload patches to upstream version")
Cc: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
2021-04-30 23:48:37 +02:00
John Audia
0d2873df15 kernel: bump 5.4 to 5.4.114
Manually rebased*
  generic/backport-5.4/700-v5.5-net-core-allow-fast-GRO-for-skbs-with-Ethernet-heade.patch

Added new backport*
  generic/backport-5.4/050-gro-fix-napi_gro_frags-Fast-GRO-breakage-due-to-IP-a.patch

All others updated automatically.

The new backport was included based on this[1] upstream commit that will be
mainlined soon.  This change is needed because Eric Dumazet's check for
NET_IP_ALIGN (landed in 5.4.114) causes huge slowdowns on drivers which use
napi_gro_frags().

Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800

No dmesg regressions, everything functional

*Credit to Alexander Lobakin
1. https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net.git/commit/?id=7ad18ff6449cbd6beb26b53128ddf56d2685aa93

Signed-off-by: John Audia <graysky@archlinux.us>
2021-04-30 23:48:37 +02:00
Rui Salvaterra
182eaa4916 kernel: bump 5.10 to 5.10.32
Deleted (reverse-appliable):
mediatek/patches-5.10/360-mtd-rawnand-mtk-Fix-WAITRDY-break-condition-and-time.patch

Automatically refreshed:
ath79/patches-5.10/0036-GPIO-add-named-gpio-exports.patch
generic/backport-5.10/600-v5.12-net-extract-napi-poll-functionality-to-__napi_poll.patch
generic/backport-5.10/601-v5.12-net-implement-threaded-able-napi-poll-loop-support.patch
generic/backport-5.10/602-v5.12-net-add-sysfs-attribute-to-control-napi-threaded-mod.patch
generic/backport-5.10/603-v5.12-net-fix-race-between-napi-kthread-mode-and-busy-poll.patch
generic/pending-5.10/600-netfilter_conntrack_flush.patch
generic/pending-5.10/613-netfilter_optional_tcp_window_check.patch
generic/pending-5.10/680-NET-skip-GRO-for-foreign-MAC-addresses.patch
generic/pending-5.10/768-net-dsa-mv88e6xxx-Request-assisted-learning-on-CPU-port.patch
lantiq/patches-5.10/0030-GPIO-add-named-gpio-exports.patch
ramips/patches-5.10/800-GPIO-add-named-gpio-exports.patch

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-04-22 15:13:56 +01:00
Rui Salvaterra
3326b5e75c treewide: switch the timer frequency to 100 Hz
Some targets select HZ=100, others HZ=250. There's no reason to select a higher
timer frequency (and 100 Hz are available in every architecture), so change all
targets to 100 Hz.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-04-21 10:31:10 +01:00
Rui Salvaterra
27b5bae2ec treewide: remove redundant ubifs kconfig symbols
For the targets which enable ubifs, these symbols are already part of the
generic kconfigs. Drop them from the target kconfigs.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-04-21 10:31:07 +01:00
David Bauer
75c01ee2b9 ramips: fix at803x patch
This patch broke while refreshing on a kernel bump. It adds the
config_aneg function twice to the AR8035 PHY now.

Restore the old behavior to restore the patches original intent.

Fixes commit 57e32650ef ("kernel: bump 5.10 to 5.10.31")
Signed-off-by: David Bauer <mail@david-bauer.net>
2021-04-18 14:42:06 +02:00
Ilya Lipnitskiy
fa6f57f66c ramips: replace mt7621s hack with upstream patch
Refresh patches.

Tested on a dual-core MT7621 device (Ubiquiti ER-X) and a single-core
MT7621 device (Netgear R6220).

This change will make future kernel upgrades easier (avoids conflicts
with upstream).

Link: https://lore.kernel.org/lkml/20210407200738.149207-1-ilya.lipnitskiy@gmail.com/
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Cc: Chuanhong Guo <gch981213@gmail.com>
2021-04-17 21:56:05 +02:00
David Bentham
17e690017d ramips: reduce spi-max-frequency for Xiaomi MI Router 4AG
Reduce spi-max-frequency for Xiaomi MI Router 4AG model

Xiaomi MI Router 4AG MTD uses two flash chips (no specific on router versions when produced from factory) - GD25Q128C and W25Q128BV.

These flash chips are capable of high frequency, but due to poor board design or manufacture process.

We are seeing the following errors in the linux kernel bootup:

`spi-nor spi0.0: unrecognized JEDEC id bytes: cc 60 1c cc 60 1c
 spi-nor: probe of spi0.0 failed with error -2`

This causes the partitions not to be detected

`VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6`

Then creates a bootloop and a bricked router.

The solution to limit this race condition is to reduce the frequency from 80 mhz to 50 mhz.

Signed-off-by: David Bentham <db260179@gmail.com>
2021-04-17 21:56:05 +02:00
John Audia
6d4ef67926 kernel: bump 5.4 to 5.4.113
Ran update_kernel.sh in a fresh clone without any existing toolchains.  No
manual intervention needed.

Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
2021-04-17 21:50:08 +02:00
Rui Salvaterra
57e32650ef kernel: bump 5.10 to 5.10.31
Automatically refreshed:
ramips/patches-5.10/710-at803x.patch

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-04-17 21:50:08 +02:00
Rui Salvaterra
a3d431ccf7 kernel: bump 5.10 to 5.10.30
Deleted (reverse-applicable):
mvebu/patches-5.10/101-ARM-dts-turris-omnia-configure-LED-2--INTn-pin-as-interrupt-pin.patch

Automatically refreshed:
bcm63xx/patches-5.10/143-gpio-fix-device-tree-gpio-hogs-on-dual-role-gpio-pin.patch
generic/backport-5.10/610-v5.13-02-netfilter-Fix-fall-through-warnings-for-Clang.patch
generic/backport-5.10/610-v5.13-10-netfilter-nftables-update-table-flags-from-the-commi.patch
generic/hack-5.10/204-module_strip.patch
generic/hack-5.10/902-debloat_proc.patch
generic/pending-5.10/203-kallsyms_uncompressed.patch
generic/pending-5.10/670-ipv6-allow-rejecting-with-source-address-failed-policy.patch
generic/pending-5.10/920-mangle_bootargs.patch
mediatek/patches-5.10/115-dts-bpi64-add-snand-support.patch
mediatek/patches-5.10/602-arm64-dts-mediatek-Split-PCIe-node-for-MT2712-MT7622.patch
mediatek/patches-5.10/900-dts-mt7622-bpi-r64-aliases-for-dtoverlay.patch
ramips/patches-5.10/323-mt7621-memory-detect.patch

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-04-16 12:58:53 +01:00
Ilya Lipnitskiy
85ca6923bc ramips: gpio-ralink: use ngpios, not ralink,num-gpios
DTS properties that match *-gpios are treated specially.

Use ngpios instead, as most GPIO drivers upstream do.

Fixes 5.10 DTS errors such as:
  OF: /palmbus@300000/gpio@600: could not find phandle

Fixes DTC warnings such as:
  Warning (gpios_property): /palmbus@300000/gpio@600:ralink,num-gpios:
  Could not get phandle node for (cell 0)

Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Cc: Daniel Golle <daniel@makrotopia.org>
2021-04-15 00:00:54 +08:00
Ilya Lipnitskiy
5f07c579f8 ramips: rt288x: replace hack with a kconfig change
Use an existing kernel config symbol to fix devices whose ramstart is
not zero. See upstream patch message for more details.

Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Cc: Tobias Wolf <dev-NTEO@vplace.de>
Cc: Daniel Golle <daniel@makrotopia.org>
2021-04-15 00:00:54 +08:00
DENG Qingfang
f99c9cd9c4 ramips: mt7530 swconfig: fix race condition in register access
The mt7530_{r,w}32 operation over MDIO uses 3 mdiobus operations and
does not hold a lock, which causes a race condition when multiple
threads try to access a register, they may get unexpected results.

To avoid this, handle the MDIO lock manually, and use the unlocked
__mdiobus_{read,write} in the critical section.

This fixes the "Ghost VLAN" artifact[1] in MT7530/7621 when the VLAN
operation and the swconfig LED link status poll race between each other.

[1] https://forum.openwrt.org/t/mysterious-vlan-ids-on-mt7621-device/64495

Signed-off-by: DENG Qingfang <dqfext@gmail.com>
2021-04-15 00:00:54 +08:00
Ilya Lipnitskiy
679c557e91 ramips: drop obsolete arcs_cmdline override patch
CONFIG_MIPS_CMDLINE_FROM_DTB is set to 'y' for all ramips targets
already, which will ensure that the value of 'bootargs' will take
precedence over whatever is in arcs_cmdline.

Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
2021-04-15 00:00:54 +08:00
Shiji Yang
882a6116d3 ramips: improve pinctrl for Youku YK-L1
1. rename led pin "air" to a more common name "wlan" and use "phy0tpt" to trigger it.
2. led "wan" can be triggered by ethernet pinctrl by default so just drop it.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2021-04-10 20:48:26 +02:00
Szabolcs Hubai
dd3c1ad8ee ramips: rt305x: use lzma-loader for ZyXEL Keenetic Lite rev.B
Fixes boot loader LZMA decompression issue,
reported by GitHub user KOLANICH at [0].

The reported LZMA ERROR has date of 2020-07-20, soon after
the device support landed:

Ralink UBoot Version: 3.5.2.4_ZyXEL

....

3: System Boot system code via Flash.
   Image Name:   MIPS OpenWrt Linux-4.14.187
   Created:      2020-07-20   3:39:11 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1472250 Bytes =  1.4 MB
   Load Address: 80000000
   Entry Point:  80000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... LZMA ERROR 1 - must RESET board to recover

[0] fea232ae8f (commitcomment-45016560)

Fixes: 4dc9ad4af8 ("ramips: add support for ZyXEL Keenetic Lite Rev.B")
Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
2021-04-08 09:20:59 +02:00
Kevin Darbyshire-Bryant
438e88e672 kernel: bump 5.10 to 5.10.27
Use update_kernel to refresh all patches, required manual updates to:

610-netfilter_match_bypass_default_checks.patch
611-netfilter_match_bypass_default_table.patch
762-net-bridge-switchdev-Refactor-br_switchdev_fdb_notif.patch
764-net-bridge-switchdev-Send-FDB-notifications-for-host.patch

Run-tested: x86_64

Nothing screamed out but any funny business with linux bridging should
suspect this update first.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2021-04-03 21:07:22 +01:00
Shiji Yang
dfc9044fad ramips: fix IMAGE_SIZE of HC5x6: fix image size of HC5x61
"firmware" partition size defined in the device tree file is 0xf70000,
so the right IMAGE_SIZE is 15808k

Fixes: df1e5d6463 ("ramips: fix partition layout of hiwifi hc5x61")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2021-04-03 18:56:02 +02:00
Daniel Engberg
e83f7e5d76 ramips: Fix booting on MQmaker WiTi board
This fixes the dreaded "lzma error 1" also reported on similar devices
Ref: https://bugs.openwrt.org/index.php?do=details&task_id=3057

Fixes: FS#3057
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
2021-04-03 18:56:02 +02:00
René van Dorst
12f3d1466a ramips: Fix booting on MTC WR1201
This fixes the dreaded "lzma error 1" also reported on similar devices
Ref: https://bugs.openwrt.org/index.php?do=details&task_id=3057

Fixes: FS#3057
Signed-off-by: René van Dorst <opensource@vdorst.com>
2021-04-03 18:56:02 +02:00
Ilya Lipnitskiy
a86c3fd800 ramips: mt7620: ralink-i2s: fix modpost error
Fixes the following error when building without CONFIG_MODULE_STRIPPED:
  FATAL: modpost: sound/soc/ralink/snd-soc-ralink-i2s: struct
  of_device_id is not terminated with a NULL entry!

Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
2021-03-31 01:10:01 +01:00
Rui Salvaterra
070ead4d4a ramips/mt7621: enable support for cpuidle
MIPS Coherent Processor Systems (CPS), which include the MT7621 SoC, support
deep sleep idle states and have a specific cpuidle driver for them.
Enable support for it, while also switching from constant timer ticks to the
idle dynticks model, with the TEO governor.

Run-tested on a Redmi AC2100.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-03-31 00:58:49 +01:00
Rui Salvaterra
9c3b2d7ff7 ramips/mt7621: drop the timer recalibration patch
We've been carrying this patch for many years [1], in order to fix a timer
calibration issue on MT7621. Turns out, after retesting with a recent kernel
(Linux 5.10), the system works perfectly fine without it (no rcu_sched stalls
or inconsistent BogoMIPS values across CPUs).

Manually refreshed:
322-mt7621-fix-cpu-clk-add-clkdev.patch
323-mt7621-memory-detect.patch

[1] https://git.openwrt.org/?p=openwrt/openwrt.git;a=commitdiff;h=6f4a903533361a2906a4d94ac6f597cd9c6c47bc

Suggested-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Tested-by: Donald Hoskins <grommish@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-03-31 00:58:49 +01:00
Rui Salvaterra
4b2e4518ac ramips/mt7621: drop the weak reordering patch
In order to fix random hangs on MT7621, we've been selecting
WEAK_REORDERING_BEYOND_LLSC for years [1]. However, these random hangs have been
most likely caused by an oversight in the MIPS implementation of the kernel
memory consistency model, which has already been fixed for some time (and
backported to stable) [2].

Manually refreshed:
321-mt7621-timer.patch

[1] https://git.openwrt.org/?p=openwrt/openwrt.git;a=commitdiff;h=5c971cd6fdd7298a2017bdb6bea870088eddb8b9
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/mips?h=linux-5.4.y&id=42344113ba7a1ed7b5654cd5270af0d5698d8521

Suggested-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Tested-by: Donald Hoskins <grommish@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-03-31 00:58:49 +01:00
Shiji Yang
b88d2850c6 ramips: correct switch config of Youku yk1
There are only two lan ports and one wan port on Youku yk1

Fixes: e9baf8265b ("ramips: add support for Youku YK1")

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[add Fixes:]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-27 16:54:15 +01:00
Kevin Darbyshire-Bryant
eb964298b3 kernel: bump 5.10 to 5.10.24
Straightforward refresh of patches using update_kernel.

Run tested: x86_64 (apu2)

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2021-03-24 11:36:31 +00:00
Shiji Yang
bf7ddb18f1 ramips: speed up spi frequency for Youku YK-L1
Youku YK-L1 has a huge storage space up to 32 MB. It is better to
use a higher spi clock to read or write serial nor flash chips.
Youku YK-L1 has Winbond w25q256fvfg on board that can support
104 MHz spi clock so 48 MHz is safe enough.
The real frequency can only be sysclk(580MHz ) /3 /(2^n) so 80 MHz
defined in dts file will set only 48 MHz in spi bus.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2021-03-22 20:54:34 +01:00
John Audia
2c81b16964 kernel: bump 5.4 to 5.4.106
Ran update_kernel.sh in a fresh clone without any existing toolchains.

Manually rebased:
  bcm27xx/950-0993-xhci-quirks-add-link-TRB-quirk-for-VL805.patch
  layerscape/701-net-0231-enetc-Use-DT-protocol-information-to-set-up-the-port.patch

Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
[remove accidental whitespace edit]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-21 22:45:20 +01:00
INAGAKI Hiroshi
b3ca1f30ef ramips: add support for ELECOM WRC-1750GST2
ELECOM WRC-1750GST2 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on
MT7621A.

Specification:

- SoC		: MediaTek MT7621A
- RAM		: DDR3 256 MiB (NT5CC128M16JR-EK)
- Flash		: SPI-NOR 32 MiB (MX25L25645GMI-08G)
- WLAN		: 2.4/5 GHz 3T3R (2x MediaTek MT7615)
- Ethernet	: 10/100/1000 Mbps x5
  - Switch	: MediaTek MT7530 (SoC)
- LEDs/Keys	: 4x/6x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - J4: 3.3V, GND, TX, RX, from ethernet port side
  - 57600n8
- Power		: 12 VDC, 1.5 A

Flash instruction using factory image:

1. Boot WRC-1750GST2 normally with "Router" mode
2. Access to "http://192.168.2.1/" and open firmware update page
   ("ファームウェア更新")
3. Select the OpenWrt factory image and click apply ("適用") button
4. Wait ~120 seconds to complete flashing

MAC addresses:

LAN	: 04:AB:18:xx:xx:23 (Factory, 0xE000 (hex))
WAN	: 04:AB:18:xx:xx:24 (Factory, 0xE006 (hex))
2.4GHz	: 04:AB:18:xx:xx:25 (Factory, 0x4    (hex))
5GHz	: 04:AB:18:xx:xx:26 (Factory, 0x8004 (hex))

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-03-21 22:45:20 +01:00
Shiji Yang
df6154848a ramips: create shared DTSI for MT7620 Phicomm K2x series devices
Improve compatibility of the device tree include file. Now a new .dtsi
file will support both PSG1218A, PSG1218B and K2G.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[improve commit title, rebase]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-21 22:45:20 +01:00
Shiji Yang
c36e47c5da ramips: increase SPI frequency for Phicomm series devices
From many teardown image in the internet, I find Phicomm K1/k2 series use
Winbond W25Q64/W25Q128 or GigaDevice GD25Q64/GD25Q128 Flash chips. both of
them support 100+ MHz clock spi operate and fast-read instruction. PSG1218
with W25x or GD25x has been tested and it can run well in OpenWrt v19.07.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[improve commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-21 22:45:20 +01:00
Shiji Yang
d160b2c824 ramips: increase SPI frequency for HIWIFI HC5x61 devices
HIWIFI HC5x61 devices support high speed spi clock up to 100+ MHz.
So set spi frequency to 80 MHz here (Due to frequency division the
real clock is 48 MHz).
I have tested HC5661 and it can run well in OpenWrt v19.07.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[adjust commit title and wrap message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-21 22:45:20 +01:00
Ilya Lipnitskiy
f65b0afadb ramips: move spi-nor-add-gd25q512 patch to generic
A SPI NOR flash should not be target-specific, so move it to generic in
case another platform needs to use it.

Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
2021-03-19 01:25:26 +01:00
Lech Perczak
410fb05b44 rampis: use lzma-loader for ZTE MF283+
Without that, after merging support to master, the device fails to boot
due to LZMA decompression error:

3: System Boot system code via Flash.
## Booting image at bc080000 ...
raspi_read: from:80000 len:40
.   Image Name:   MIPS OpenWrt Linux-5.4.99
   Created:      2021-02-25  23:35:00 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1786664 Bytes =  1.7 MB
   Load Address: 80000000
   Entry Point:  80000000
raspi_read: from:80040 len:1b4328
............................   Verifying Checksum ... OK
   Uncompressing Kernel Image ... LZMA ERROR 1 - must RESET board to recover

Use lzma-loader to fix it.

Fixes: 59d065c9f8 ("ramips: add support for ZTE MF283+")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2021-03-19 01:25:26 +01:00
Shiji Yang
a94a20373b ramips: improve GPIO pin control for HC5x61
HC5661 does not have USB port, remove usb power control pin.
HC5x61 do not have LAN LEDs, remove ethernet LED control pin.
Only HC5861 has PA in 2.4G channel.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2021-03-19 01:25:26 +01:00
David Bauer
ac5675ec8f ramips: fix broken UniFi 6 Lite image
Ubiquiti's own bootloader expects the configuration mode to be present
with a "@" instead of a "-" for the sperator character. Otherwise
booting of the image fails.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-03-18 00:54:25 +01:00
Kabuli Chana
1cd098784e kernel: bump 5.10 to 5.10.23
update kernel to 5.10.23, rebase patches, deleted upstreamed patch:

target/linux/generic/backport-5.10/830-v5.12-0001-net-usb-qmi_wwan-support-ZTE-P685M-modem.patch

compile / test - mvebu / mamba, rango

Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
[refresh again]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-13 17:06:42 +01:00
John Audia
e7fa97b326 kernel: bump 5.4 to 5.4.105
Ran update_kernel.sh in a fresh clone without any existing toolchains.

Removed upstreamed generic-backports:
  830-v5.12-0001-net-usb-qmi_wwan-support-ZTE-P685M-modem.patch
  831-v5.9-usbip-tools-fix-build-error-for-multiple-definition.patch
  755-v5.8-net-dsa-add-GRO-support-via-gro_cells.patch

Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
Tested-by: Curtis Deptuck <curtdept@me.com> [x86/64]
[squash patches]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-13 17:06:35 +01:00
Adrian Schmutzler
9397b22df1 treewide: make AddDepends/usb-serial selective
Make packages depending on usb-serial selective, so we do not have
to add kmod-usb-serial manually for every device.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-06 12:38:38 +01:00
Adrian Schmutzler
85b1f4d8ca treewide: remove execute bit and shebang from board.d files
So far, board.d files were having execute bit set and contained a
shebang. However, they are just sourced in board_detect, with an
apparantly unnecessary check for execute permission beforehand.

Replace this check by one for existance and make the board.d files
"normal" files, as would be expected in /etc anyway.

Note:

This removes an apparantly unused '#!/bin/sh /etc/rc.common' in
target/linux/bcm47xx/base-files/etc/board.d/01_network

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-06 11:30:06 +01:00
Ilya Lipnitskiy
b021642cac ramips: 5.10: refresh configs
Run-tested on Ubiquiti EdgeRouter X.

Compile tested on all other subtargets.

Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
2021-03-06 11:24:12 +01:00
Ilya Lipnitskiy
10267e1729 ramips: 5.10: port and refresh patches, ralink drv
Enable testing kernel.

Fix compile errors by using new kernel APIs.

Fix fuzz by manually editing patches to ensure the code goes in the
right place.

For 721-NET-no-auto-carrier-off-support.patch, revert upstream commit
a307593a6 to keep the OpenWrt ralink driver operational.

Add mt7621-pci-phy patch to select REGMAP_MMIO as discussed in PR #3693
and #3952.

Run automatic quilt refresh on the rest.

Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
2021-03-06 11:24:12 +01:00
Ilya Lipnitskiy
ef1e652016 ramips: 5.10: rename patches to follow guide
Rename patches to follow the 3-digit classification from the OpenWrt
Developer Guide.

https://openwrt.org/docs/guide-developer/build-system/use-patches-with-buildsystem#naming_patches

Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
2021-03-06 11:24:12 +01:00
Ilya Lipnitskiy
3149d8e7be ramips: 5.10: delete upstreamed patches
0098-disable_cm.patch is not needed because upstream fixed CM handling.

The rest are straightforward removals of upstreamed patches.

Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
2021-03-06 11:24:12 +01:00
Ilya Lipnitskiy
eda836e390 ramips: 5.10: copy patches from 5.4
Strict copy, no changes made.

Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
2021-03-06 11:24:12 +01:00
Ilya Lipnitskiy
a9966793e8 ramips: copy config-5.4 to config-5.10
Strict copy, no changes made.

Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
2021-03-06 11:24:12 +01:00
Adrian Schmutzler
cc4ee2eeb4 Revert "ramips: add support for kernel 5.10"
This reverts commit b4aad29a1d.

This was accidentally folded into a single commit. Remove it and
apply it properly again.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-06 11:23:38 +01:00
Ilya Lipnitskiy
2629d2d5b1 apm821xx, mt7621, oxnas, rockchip, zynq: remove PLUGIN_HOSTCC
This config symbol should not be defined in target configs.

Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
2021-03-06 03:52:33 +00:00
Ilya Lipnitskiy
b4aad29a1d
ramips: add support for kernel 5.10
Enable testing kernel.

Delete upstreamed patches:
 0098-disable_cm.patch can be dropped, upstream fixed CM handling.

Fix compile errors by using new kernel APIs.

Fix fuzz by manually editing patches to ensure the code goes in the
right place.

For 721-NET-no-auto-carrier-off-support.patch, revert upstream commit
a307593a6 to keep the OpenWrt ralink driver operational.

Add mt7621-pci-phy patch to select REGMAP_MMIO as discussed in PR #3693
and #3952.

Rename patches to follow the 3-digit classification from the OpenWrt
Developer Guide.

Run automatic quilt refresh.

Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
2021-03-05 23:55:51 +00:00
Ilya Lipnitskiy
38ba1f9b4c
ramips: 5.4: refresh configs
Automatic refresh by running make kernel_oldconfig on each target.

Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
2021-03-05 23:55:46 +00:00
Ilya Lipnitskiy
58ad113087 ramips: rename mtk-hsdma to hsdma-mt7621
Follows upstream rename:
https://lore.kernel.org/driverdev-devel/20210130034507.2115280-1-ilya.lipnitskiy@gmail.com/

Fixes ramips builds on 5.4.102

Cc: John Audia <graysky@archlinux.us>
Cc: David Bauer <mail@david-bauer.net>
Cc: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
2021-03-04 23:43:02 -10:00
Jason A. Donenfeld
196f3d586f kernel-5.4: bump to 5.4.102 and refresh patches
5.4.102 backported a lot of stuff that our WireGuard backport already
did, in addition to other patches we had, so those patches were
removed from that part of the series. In the process other patches were
refreshed or reworked to account for upstream changes.

This commit involved `update_kernel.sh -v -u 5.4`.

Cc: John Audia <graysky@archlinux.us>
Cc: David Bauer <mail@david-bauer.net>
Cc: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
2021-03-04 22:06:53 +01:00
Shiji Yang
df1e5d6463 ramips: fix partition layout of hiwifi hc5x61
Changes:
 * Increase "oem" partition size from 0x10000 to 0x20000
 * Correct partition lables, synchronize with official firmware

Evidence:
It should be the same as hiwifi hc5x61a and the fact indeed the
case. Here is part of dmesg boot log read from official firmware:
[    1.470000] Creating 7 MTD partitions on "raspi":
[    1.470000] 0x000000000000-0x000000030000 : "u-boot"
[    1.480000] 0x000000030000-0x000000040000 : "hw_panic"
[    1.490000] 0x000000040000-0x000000050000 : "Factory"
[    1.490000] 0x000000fc0000-0x000000fe0000 : "oem"
[    1.500000] 0x000000fe0000-0x000000ff0000 : "bdinfo"
[    1.510000] 0x000000ff0000-0x000001000000 : "backup"
[    1.510000] 0x000000050000-0x000000fc0000 : "firmware"

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2021-03-01 00:34:23 +01:00
Lech Perczak
59d065c9f8 ramips: add support for ZTE MF283+
ZTE MF283+ is a dual-antenna LTE category 4 router, based on Ralink
RT3352 SoC, and built-in ZTE P685M PCIe MiniCard LTE modem.

Hardware highlighs:
- CPU: MIPS24KEc at 400MHz,
- RAM: 64MB DDR2,
- Flash: 16MB SPI,
- Ethernet: 4 10/100M port switch with VLAN support,
- Wireless: Dual-stream 802.11n (RT2860), with two internal antennas,
- WWAN: Built-in ZTE P685M modem, with two internal antennas and two
  switching SMA connectors for external antennas,
- FXS: Single ATA, with two connectors marked PHONE1 and PHONE2,
  internally wired in parallel by 0-Ohm resistors, handled entirely by
  internal WWAN modem.
- USB: internal miniPCIe slot for modem,
  unpopulated USB A connector on PCB.
- SIM slot for the WWAN modem.
- UART connector for the console (unpopulated) at 3.3V,
  pinout: 1: VCC, 2: TXD, 3: RXD, 4: GND,
  settings: 57600-8-N-1.
- LEDs: Power (fixed), WLAN, WWAN (RGB),
  phone (bicolor, controlled by modem), Signal,
  4 link/act LEDs for LAN1-4.
- Buttons: WPS, reset.

Installation:
As the modem is, for most of the time, provided by carriers, there is no
possibility to flash through web interface, only built-in FOTA update
and TFTP recovery are supported.

There are two installation methods:
(1) Using serial console and initramfs-kernel - recommended, as it
allows you to back up original firmware, or
(2) Using TFTP recovery - does not require disassembly.

(1) Using serial console:
To install OpenWrt, one needs to disassemble the
router and flash it via TFTP by using serial console:
- Locate unpopulated 4-pin header on the top of the board, near buttons.
- Connect UART adapter to the connector. Use 3.3V voltage level only,
  omit VCC connection. Pin 1 (VCC) is marked by square pad.
- Put your initramfs-kernel image in TFTP server directory.
- Power-up the device.
- Press "1" to load initramfs image to RAM.
- Enter IP address chosen for the device (defaults to 192.168.0.1).
- Enter TFTP server IP address (defaults to 192.168.0.22).
- Enter image filename as put inside TFTP server - something short,
  like firmware.bin is recommended.
- Hit enter to load the image. U-boot will store above values in
  persistent environment for next installation.
- If you ever might want to return to vendor firmware,
  BACK UP CONTENTS OF YOUR FLASH NOW.
  For this router, commonly used by mobile networks,
  plain vendor images are not officially available.
  To do so, copy contents of each /dev/mtd[0-3], "firmware" - mtd3 being the
  most important, and copy them over network to your PC. But in case
  anything goes wrong, PLEASE do back up ALL OF THEM.
- From under OpenWrt just booted, load the sysupgrade image to tmpfs,
  and execute sysupgrade.

(2) Using TFTP recovery
- Set your host IP to 192.168.0.22 - for example using:
sudo ip addr add 192.168.0.22/24 dev <interface>
- Set up a TFTP server on your machine
- Put the sysupgrade image in TFTP server root named as 'root_uImage'
  (no quotes), for example using tftpd:
  cp openwrt-ramips-rt305x-zte_mf283plus-squashfs-sysupgrade.bin /srv/tftp/root_uImage
- Power on the router holding BOTH Reset and WPS buttons held for around
  5 seconds, until after WWAN and Signal LEDs blink.
- Wait for OpenWrt to start booting up, this should take around a
  minute.

Return to original firmware:
Here, again there are two possibilities are possible, just like for
installation:
(1) Using initramfs-kernel image and serial console
(2) Using TFTP recovery

(1) Using initramfs-kernel image and serial console
- Boot OpenWrt initramfs-kernel image via TFTP the same as for
  installation.
- Copy over the backed up "firmware.bin" image of "mtd3" to /tmp/
- Use "mtd write /tmp/firmware.bin /dev/mtd3", where firmware.bin is
  your backup taken before OpenWrt installation, and /dev/mtd3 is the
  "firmware" partition.

(2) Using TFTP recovery
- Follow the same steps as for installation, but replacing 'root_uImage'
  with firmware backup you took during installation, or by vendor
  firmware obtained elsewhere.

A few quirks of the device, noted from my instance:
- Wired and wireless MAC addresses written in flash are the same,
  despite being in separate locations.
- Power LED is hardwired to 3.3V, so there is no status LED per se, and
  WLAN LED is controlled by WLAN driver, so I had to hijack 3G/4G LED
  for status - original firmware also does this in bootup.
- FXS subsystem and its LED is controlled by the
  modem, so it work independently of OpenWrt.
  Tested to work even before OpenWrt booted.
  I managed to open up modem's shell via ADB,
  and found from its kernel logs, that FXS and its LED is indeed controlled
  by modem.
- While finding LEDs, I had no GPL source drop from ZTE, so I had to probe for
  each and every one of them manually, so this might not be complete -
  it looks like bicolor LED is used for FXS, possibly to support
  dual-ported variant in other device sharing the PCB.
- Flash performance is very low, despite enabling 50MHz clock and fast
  read command, due to using 4k sectors throughout the target. I decided
  to keep it at the moment, to avoid breaking existing devices - I
  identified one potentially affected, should this be limited to under
  4MB of Flash. The difference between sysupgrade durations is whopping
  3min vs 8min, so this is worth pursuing.

In vendor firmware, WWAN LED behaviour is as follows, citing the manual:
- red - no registration,
- green - 3G,
- blue - 4G.
Blinking indicates activity, so netdev trigger mapped from wwan0 to blue:wwan
looks reasonable at the moment, for full replacement, a script similar to
"rssileds" would need to be developed.

Behaviour of "Signal LED" in vendor firmware is as follows:
- Off - no signal,
- Blinking - poor coverage
- Solid - good coverage.

A few more details on the built-in LTE modem:
Modem is not fully supported upstream in Linux - only two CDC ports
(DIAG and one for QMI) probe. I sent patches upstream to add required device
IDs for full support.
The mapping of USB functions is as follows:
- CDC (QCDM) - dedicated to comunicating with proprietary Qualcomm tools.
- CDC (PCUI) - not supported by upstream 'option' driver yet. Patch
  submitted upstream.
- CDC (Modem) - Exactly the same as above
- QMI - A patch is sent upstream to add device ID, with that in place,
  uqmi did connect successfully, once I selected correct PDP context
  type for my SIM (IPv4-only, not default IPv4v6).
- ADB - self-explanatory, one can access the ADB shell with a device ID
  added to 51-android.rules like so:

SUBSYSTEM!="usb", GOTO="android_usb_rules_end"
LABEL="android_usb_rules_begin"
SUBSYSTEM=="usb", ATTR{idVendor}=="19d2", ATTR{idProduct}=="1275", ENV{adb_user}="yes"
ENV{adb_user}=="yes", MODE="0660", GROUP="plugdev", TAG+="uaccess"
LABEL="android_usb_rules_end"

While not really needed in OpenWrt, it might come useful if one decides to
move the modem to their PC to hack it further, insides seem to be pretty
interesting. ADB also works well from within OpenWrt without that. O
course it isn't needed for normal operation, so I left it out of
DEVICE_PACKAGES.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[remove kmod-usb-ledtrig-usbport, take merged upstream patches]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-26 13:57:54 +01:00
DENG Qingfang
06af45ec05 ramips: remove obsolete mx25l25635f compatible hack
The kernel bump to 5.4 has removed the mx25l25635f hack, and the
mx25l25635f compatible is no longer required.

Signed-off-by: DENG Qingfang <dqfext@gmail.com>
2021-02-24 00:30:40 +01:00
Stijn Segers
06356f0020 ramips: overwrite reset gpio properties in DIR-860L DTS
As suggested by Sergio, this adds GPIOs 19 and 8 explicitly into the
DIR-860L DTS, so the PCI-E ports get reset and the N radio (radio1)
on PCI-E port 1 comes up reliably.

Fixes the following error that popped up in dmesg:

    [    1.638942] mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK)

Suggested-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
2021-02-23 21:10:56 +01:00
Sander Vanheule
773949c152 ramips: mt7621: enable SX150x driver
The Netgear R6800 and R6700v2 devices have a Semtech SX1503 GPIO
expander controlling the device LEDs. This expander was initially
supported on 4.14, but support was lost in the transition to 5.4.

Since this driver cannot be built as a kernel module, enable it in the
kernel config for all mt7621 devices.

Run-tested on a Netgear R6800.

Cc: Stijn Segers <foss@volatilesystems.org>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Segers <foss@volatilesystems.org>
2021-02-23 21:10:56 +01:00
Shiji Yang
d1176ad95a ramips: improve gpio control for Phicomm PSG1218
Description:
1. From key and led config setting, we can find only "uartf" and "i2c" are used
as gpio by check mt7620 datasheet. It's time to remove unused pin group.

2. PSG1218 only have three led, so we can remove ethernet led pinctrl. refer to
Phicomm K2G.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2021-02-23 18:31:35 +01:00
Shiji Yang
567a88e4b9 ramips: fix Phicomm PSG1218A switch port labels
The lan port sequence was reversed compared to the labels.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[improve commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-22 18:49:57 +01:00
Adrian Schmutzler
d4520d75a1 ramips: move aliases to the top in SoC DTSI files
The aliases node is expected as one of the first entries, and
having it there matches alphabetic sorting as well.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-22 18:49:57 +01:00
Adrian Schmutzler
86a4d78022 ramips: drop redundant definitions of serial0 in aliases
These were redefines of the same value already set in the SoC dtsi
files.

Reported-by: Shiji Yang <yangshiji66@qq.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-22 18:49:57 +01:00
Shiji Yang
55263ffedb ramips: correct/add Phicomm K2x WAN/label MAC address
Phicomm K2G:
add missing label_mac

Phicomm PSG1218A & PSG1218B:
The previous wan mac was set as factory@0x28 +1 (originally based
on the default case for the ramips target), but the correct wan mac
is factory@0x28 -1, being equal to factory@0x2e.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[minor commit title/message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-22 17:32:35 +01:00
Stijn Segers
af1b6799c6 ramips: overwrite reset gpio properties in EX6150 DTS
The Netgear EX6150 can, just like the D-Link DIR-860L rev B1, fail to
initialise both radios in some cases. Add the reset GPIOs explicitly
so the PCI-E devices get re-initialised properly. See also FS #3632.

Error shows up in dmesg as follows:

  [    1.560764] mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK)

Tested-by: Kurt Roeckx <kurt@roeckx.be>
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
[removed period from commit title]
Signed-off-by: David Bauer <mail@david-bauer.net>
2021-02-20 01:27:00 +01:00
Seo Suchan
ca6954e2dc ramips: use lzma-loader for Wevo devices
As kernel size increased it start to fail to load squishfs image,
using lzma-loader fixed it.
wevo_11acnas is almost same device as w2914ns-v2 except ram size,
so I expect same thing would've happen in that device too.

Signed-off-by: Seo Suchan <abnoeh@mail.com>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
2021-02-19 14:09:50 +01:00
Sander Vanheule
1e75909a35 ramips: mt7621: add TP-Link EAP235-Wall support
The TP-Link EAP235-Wall is a wall-mounted, PoE-powered AC1200 access
point with four gigabit ethernet ports.

When connecting to the device's serial port, it is strongly advised to
use an isolated UART adapter. This prevents linking different power
domains created by the PoE power supply, which may damage your devices.

The device's U-Boot supports saving modified environments with
`saveenv`. However, there is no u-boot-env partition, and saving
modifications will cause the partition table to be overwritten. This is
not an issue for running OpenWrt, but will prevent the vendor FW from
functioning properly.

Device specifications:
* SoC: MT7621DAT
* RAM: 128MiB
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (MT7603EN): b/g/n, 2x2
* Wireless 5GHz (MT7613BEN): a/n/ac, 2x2
* Ethernet: 4× GbE
  * Back side: ETH0, PoE PD port
  * Bottom side: ETH1, ETH2, ETH3
* Single white device LED
* LED button, reset button (available for failsafe)
* PoE pass-through on port ETH3 (enabled with GPIO)

Datasheet of the flash chip specifies a maximum frequency of 33MHz, but
that didn't work. 20MHz gives no errors with reading (flash dump) or
writing (sysupgrade).

Device mac addresses:
Stock firmware uses the same MAC address for ethernet (on device label)
and 2.4GHz wireless. The 5GHz wireless address is incremented by one.
This address is stored in the 'info' ('default-mac') partition at an
offset of 8 bytes.
From OEM ifconfig:
    eth     a4:2b:b0:...:88
    ra0     a4:2b:b0:...:88
    rai0    a4:2b:b0:...:89

Flashing instructions:
* Enable SSH in the web interface, and SSH into the target device
* run `cliclientd stopcs`, this should return "success"
* upload the factory image via the web interface

Debricking:
U-boot can be interrupted during boot, serial console is 57600 baud, 8n1
This allows installing a sysupgrade image, or fixing the device in
another way.
* Access serial header from the side of the board, close to ETH3,
  pin-out is (1:TX, 2:RX, 3:GND, 4:3.3V), with pin 1 closest to ETH3.
* Interrupt bootloader by holding '4' during boot, which drops the
  bootloader into its shell
* Change default 'serverip' and 'ipaddr' variables (optional)
* Download initramfs with `tftpboot`, and boot image with `bootm`
    # tftpboot 84000000 openwrt-initramfs.bin
    # bootm

Revert to stock:
Using the tplink-safeloader utility from the firmware-utils package,
TP-Link's firmware image can be converted to an OpenWrt-compatible
sysupgrade image:
  $ ./staging_dir/host/bin/tplink-safeloader -B EAP235-WALL-V1 \
      -z EAP235-WALLv1_XXX_up_signed.bin -o eap235-sysupgrade.bin

This can then be flashed using the OpenWrt sysupgrade interface. The
image will appear to be incompatible and must be force flashed, without
keeping the current configuration.

Known issues:
- DFS support is incomplete (known issue with MT7613)
- MT7613 radio may stop responding when idling, reboot required.
  This was an issue with the ddc75ff704 version of mt76, but appears to
  have improved/disappeared with bc3963764d.
  Error notice example:
  [ 7099.554067] mt7615e 0000:02:00.0: Message 73 (seq 1) timeout

Hardware was kindly provided for porting by Stijn Segers.

Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2021-02-19 14:00:08 +01:00
Stijn Segers
0265cba40a ramips: remove factory image for TP-Link Archer C20 v1
Similarly to the Archer C2 v1, the Archer C20 v1 will brick when one
tries to flash an OpenWrt factory image through the TP-Link web UI.
The wiki page contains an explicit warning about this [1].

Disable the factory image altogether since it serves no purpose.

[1] https://openwrt.org/toh/tp-link/tp-link_archer_c20_v1#installation

Signed-off-by: Stijn Segers <foss@volatilesystems.org>
2021-02-19 13:56:27 +01:00
John Audia
5d3a6fd970 kernel: bump 5.4 to 5.4.99
Ran update_kernel.sh in a fresh clone without any existing toolchains.
No manual changes needed.

Build system: x86_64
Build-tested: bcm27xx/bcm2711

Signed-off-by: John Audia <graysky@archlinux.us>
2021-02-18 20:04:50 +01:00
Kurt Roeckx
539966554d ramips: mark toggle input on EX6150 as a switch
The Netgear EX6150 has an Access Point/Extender switch. Set it as
an EV_SW. Otherwise when it's set to Access Point, it will trigger
failsafe mode during boot.

Fixes: FS#3590
Signed-off-by: Kurt Roeckx <kurt@roeckx.be>
2021-02-15 00:00:38 +01:00
Sander Vanheule
69551a2442 ramips: manage low reset lines
The bootloader of a number of recent TP-Link devices does not properly
initialise the MT7621's internal switch when booting from flash. To
enable the mt7530 driver to clear the reset on the switch, the ramips
reset controller must be allowed to toggle these.

Backport upstream commit 3f9ef7785a9c from mips-next to allow control of
the "mcm" reset line.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2021-02-14 09:33:42 +01:00
Stijn Segers
ad5e29d38a ramips: remove factory image for TP-Link Archer C2 v1
Initial commit 8375623a06 ("ramips: add support for TP-Link Archer
C2") contains detailed installation instructions, which do not mention
a factory image. From what I can see, no support to install OpenWrt
through the vendor web interface has been added since. The factory
image is also conspicuously absent from the device page in the wiki.
Yet, it is available for download.

I bricked my Archer C2 loading the factory image through the web UI.
Serial showed this error during bootloop:

  Uncompressing Kernel Image ... LZMA ERROR 1 - must RESET board to recover

This patch disables the undocumented factory image so users won't get
tricked into thinking easy web UI flashing actually works.

Signed-off-by: Stijn Segers <foss@volatilesystems.org>
2021-02-13 21:21:01 +01:00
INAGAKI Hiroshi
08768b44d9 ramips: add support for ELECOM WRC-1167FS
ELECOM WRC-1167FS is a 2.4/5 GHz band 11ac (WiFi-5) router, based on
MT7628AN.

Specification:

- SoC		: MediaTek MT7628AN
- RAM		: DDR2 64 MiB (NT5TU32M16FG-AC)
- Flash		: SPI-NOR 16 MiB (W25Q128JVSIQ)
- WLAN		: 2.4/5 GHz 2T2R
  - 2.4 GHz	: MediaTek MT7628AN (SoC)
  - 5 GHz	: MediaTek MT7612E
- Ethernet	: 10/100 Mbps x2
  - Switch	: MT7628AN (SoC)
- LEDs/Keys	: 6x, 3x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - J1: 3.3V, GND, TX, RX from "J1" marking
  - 57600n8
- Power		: 12 VDC, 1 A

Flash instruction using factory image:

1. Boot WRC-1167FS normally
2. Access to "http://192.168.2.1/" and open firmware update page
   ("ファームウェア更新")
3. Select the OpenWrt factory image and click apply ("適用") button to
   perform firmware update
4. Wait ~120 seconds to complete flashing

Notes:

- Last 0x800000 (8 MiB) in SPI-NOR flash is not used on stock firmware

- Additional padding in factory image is required to avoid incomplete
  flashing on stock firmware

MAC addresses:

- LAN	: BC:5C:4C:xx:xx:68 (Config, ethaddr (text) / Factory, 0x28   (hex))
- WAN	: BC:5C:4C:xx:xx:69 (Config, wanaddr (text) / Factory, 0x22   (hex))
- 2.4GHz: BC:5C:4C:xx:xx:6A (Config, rmac    (text) / Factory, 0x4    (hex))
- 5GHz	: BC:5C:4C:xx:xx:6B (Config, rmac2   (text) / Factory, 0x8004 (hex))

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-02-11 16:37:53 +01:00
Adrian Schmutzler
598b29585e target: use SPDX license identifiers on Makefiles
Use SPDX license tags to allow machines to check licenses.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-10 15:47:18 +01:00
Andrew Pikler
cd2b661453 ramips: add support for Cudy WR1300
Specifications:
 - SoC: MediaTek MT7621AT
 - RAM: 128 MB (DDR3)
 - Flash: 16 MB (SPI NOR)
 - WiFi: MediaTek MT7603E, MediaTek MT7612E
 - Switch: 1 WAN, 4 LAN (Gigabit)
 - Ports: 1 USB 3.0
 - Buttons: Reset, WPS
 - LEDs: Power, System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS, USB
 - Power: DC 12V 1A tip positive

UART Serial:
  115200 baud
  Located on unpopulated 4 pin header near J4:

  J4
  [o] Rx
  [o] Tx
  [o] GND
  [ ] Vcc - Do not connect

Installation:

Download and flash the manufacturer's built OpenWRT image available at
http://www.cudytech.com/openwrt_software_download
Install the new OpenWRT image via luci (System -> Backup/Flash firmware)
Be sure to NOT keep settings. The force upgrade may need to be checked
due to differences in router naming conventions.

Recovery:
 - Loads only signed manufacture firmware due to bootloader RSA verification
 - serve tftp-recovery image as /recovery.bin on 192.168.1.88/24
 - connect to any lan ethernet port
 - power on the device while holding the reset button
 - wait at least 8 seconds before releasing reset button for image to
   download
 - See http://www.cudytech.com/newsinfo/547425.html

MAC addresses as verified by OEM firmware:

use   address   source
LAN   *:f0      label
WAN   *:f1      label + 1
2g    *:f0      label
5g    *:f2      label + 2

The label MAC address is found in bdinfo 0xde00.

Signed-off-by: Andrew Pikler <andrew.pikler@gmail.com>
2021-02-09 13:58:18 +01:00
Chukun Pan
82032f3509 ramips: add support for JCG Y2
JCG Y2 is an AC1300M router

Hardware specs:
  SoC: MediaTek MT7621AT
  Flash: Winbond W25Q128JVSQ 16MiB
  RAM: Nanya NT5CB128M16 256MiB
  WLAN: 2.4/5 GHz 2T2R (1x MediaTek MT7615)
  Ethernet: 10/100/1000 Mbps x5
  LED: POWER, INTERNET, 2.4G, 5G
  Button: Reset
  Power: DC 12V,1A

Flash instructions:
  Upload factory.bin in stock firmware's upgrade page.

MAC addresses map:
  0x0004  *:c8  wlan2g/wlan5g/label
  0xe000  *:c7  lan
  0xe006  *:c6  wan

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2021-02-09 13:10:33 +01:00
Szabolcs Hubai
1e9afcca56 ramips: disable default build for HooToo HT-TM02
While the latest version of 19.07 release is usable,
the current master is unbootable on the device in a normal way.

"Normal way" installations includes:
- sysupgrade (e.g. from 19.07)
- RESET button recovery with Ron Curry's (Wingspinner) UBoot image
  (10.10.10.3 + "Kernal.bin")
- RESET button recovery with original U-Boot
  (10.10.10.254 + "kernel")

One could flash and boot the latest master sysupgrade image successfully
with serial access to the device. But a sysupgrade from this state still
breaks the U-Boot and soft-bricks the device.

Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
2021-02-07 22:06:57 +01:00
Adrian Schmutzler
1c0e13db43 ramips: mt7621: use preferred logic in lib/upgrade/iodata.sh
shellcheck recommends || and && over "-a" and "-o" because the
latter are not well defined.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-07 21:58:51 +01:00
INAGAKI Hiroshi
88fbddb49d ramips: add support for I-O DATA WN-DX1200GR
I-O DATA WN-DX1200GR is a 2.4/5 GHz band 11ac (WiFi-5) router, based on
MT7621A.

Specification:

- SoC		: MediaTek MT7621A
- RAM		: DDR3 128 MiB
- Flash		: raw NAND 128 MiB
- WLAN		: 2.4/5 GHz 2T2R
  - 2.4 GHz	: MediaTek MT7603E
  - 5 GHz	: MediaTek MT7613BE
- Ethernet	: 10/100/1000 Mbps x5
  - Switch	: MediaTek MT7530 (SoC)
- LEDs/keys	: 2x/3x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - J5: 3.3V, TX, RX, NC, GND from triangle-mark
  - 57600n8
- Power		: 12 VDC, 1 A

Flash instruction using initramfs image:

1. Boot WN-DX1200GR normally
2. Access to "http://192.168.0.1/" and open firmware update page
   ("ファームウェア")
3. Select the OpenWrt initramfs image and click update ("更新") button
   to perform firmware update
4. On the initramfs image, perform sysupgrade with the
   squashfs-sysupgrade image
5. Wait ~120 seconds to complete flashing

Notes:

- currently, mt7615e driver in mt76 doesn't fully support MT7613
  (MT7663) wifi chip
  - the eeprom data in flash is not used by mt7615e driver and the
    driver reports the tx-power up to 3dBm
  - the correct MAC address for MT7613BE in eeprom data cannot be
    assigned to the phy

- last 0x80000 (512 KiB) in NAND flash is not used on stock firmware

- stock firmware requires "customized uImage header" (called as "combo
  image") by MSTC (MitraStar Technology Corp.), but U-Boot doesn't

  - uImage magic ( 0x0 - 0x3 ) : 0x434F4D43 ("COMC")
  - header crc32 ( 0x4 - 0x7 ) : with "data length" and "data crc32"
  - image name   (0x20 - 0x37) : model ID and firmware versions
  - data length  (0x38 - 0x3b) : kernel + rootfs
  - data crc32   (0x3c - 0x3f) : kernel + rootfs

MAC addresses:

LAN:	50:41:B9:xx:xx:08 (Ubootenv, ethaddr (text) / Factory, 0x1E000 (hex))
WAN:	50:41:B9:xx:xx:0A (Factory,  0x1E006 (hex))
2.4GHz:	50:41:B9:xx:xx:08 (Factory,  0x4     (hex))
5GHz:	50:41:B9:xx:xx:09 (Factory,  0x8004  (hex))

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[add check whether dflag_offset is set]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-07 21:58:51 +01:00
Yanase Yuki
d468ff97b7 build: move elx-header into image-commands.mk
ELECOM WAB-I1750-PS will need this in ath79, so move it to common
Makefile.

Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
2021-02-05 21:57:19 +01:00
Adrian Schmutzler
3f4d1dad00 ramips: replace full-text licenses by SPDX identifier
This replaces several full-text and abbreviated licenses found in
DTS files by the corresponding SPDX identifiers.

This should make it easier to identify the license both by humans
and machines.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-05 18:18:00 +01:00
David Bentham
4a18039785 ramips: add support for UniElec U7621-01
UniElec U7621-01 is a router platform board, the smaller model of
the U7621-06.
The device has the following specifications:

- MT7621AT (880 MHz)
- 256 of RAM (DDR3)
- 16 MB of FLASH (SPI NOR)
- 5x 1 Gbps Ethernet (MT7621 built-in switch)
- 1x 2.4Ghz MT7603E
- 1x 5Ghz MT7612
- 1x miniPCIe slots (PCIe bus only)
- 1x miniSIM slot
- 1x USB 2.0 (uses the usb 3.0 driver)
- 8x LEDs (1x GPIO-controlled)
- 1x reset button
- 1x UART header (4-pins)
- 1x GPIO header (30-pins)
- 1x DC jack for main power (12 V)

The following has been tested and is working:

- Ethernet switch
- 1x 2.4Ghz MT7603E (wifi)
- 1x 5Ghz MT7612 (wifi)
- miniPCIe slots (tested with Wi-Fi cards and LTE modem cards)
- miniSIM slot (works with normal size simcard)
- sysupgrade
- reset button

Installation:

This board has no locked down bootloader. The seller can be asked to
install openwrt v18.06, so upgrades are standard sysupgrade method.

Recovery:

This board contains a Chinese, closed-source bootloader called Breed
(Boot and Recovery Environment for Embedded Devices). Breed supports web
recovery and to enter it, you keep the reset button pressed for around
5 seconds during boot. Your machine will be assigned an IP through DHCP
and the router will use IP address 192.168.1.1. The recovery website is
in Chinese, but is easy to use. Click on the second item in the list to
access the recovery page, then the second item on the next page is where
you select the firmware. In order to start the recovery, you click the
button at the bottom.

LEDs list (left to right):

- ESW_P0_LED_0
- ESW_P1_LED_0
- ESW_P2_LED_0
- ESW_P3_LED_0
- ESW_P4_LED_0
- CTS2_N (GPIO10, configured as "status" LED)
- LED_WLAN# (connected with pin 44 in wifi1 slot)

Signed-off-by: David Bentham <db260179@gmail.com>
[add DEVICE_VARIANT, fix DEVICE_PACKAGES, remove &gpio]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-05 17:31:51 +01:00
Ewan Parker
ddafcc7947 ramips: add support for Hi-Link HLK-7688A
Specifications:

  - SoC: MediaTek MT7688AN
  - RAM: 128 MB
  - Flash: 32 MB
  - Ethernet: 5x 10/100 (1x WAN, 4x LAN)
  - Wireless: built in 2.4GHz (bgn)
  - USB: 1x USB 2.0 port
  - Buttons: 1x Reset
  - LEDs: 1x (WiFi)

Flash instructions:

  - Configure TFTP server with IP address 10.10.10.3
  - Name the firmware file as firmware.bin
  - Connect any Ethernet port to the TFTP server's LAN
  - Choose option 2 in U-Boot
  - Alternatively choose option 7 to upload firmware to the built-in
    web server

MAC addresses as verified by OEM firmware:

  use   address   source
  2g    *:XX      factory 0x4
  LAN   *:XX+1    factory 0x28
  WAN   *:XX+1    factory 0x2e

Notes:

This board is ostensibly a module containing the MediaTek MT7688AN SoC,
128 MB DDR2 SDRAM and 32 MB flash storage.  The SoC can be operated in
IoT Gateway Mode or IoT Device Mode.

From some vendors the U-Boot that comes installed operates on UART 2
which is inaccessible in gateway mode and operates unreliably in the
Linux kernel when using more than 64 MB of RAM.  For those, updating
U-Boot is recommended.

Signed-off-by: Ewan Parker <ewan@ewan.cc>
[add WLAN to 01_leds]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-05 14:54:47 +01:00
INAGAKI Hiroshi
eb11cd9ea3 ramips: add support for ELECOM WRC-2533GHBK-I
ELECOM WRC-2533GHBK-I is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based
on MT7621A.

Specification:

- SoC		: MediaTek MT7621A
- RAM		: DDR3 128 MiB
- Flash		: SPI-NOR 16 MiB
- WLAN		: 2.4/5 GHz 4T4R (2x MediaTek MT7615)
- Ethernet	: 10/100/1000 Mbps x5
  - Switch	: MediaTek MT7530 (SoC)
- LED/keys	: 4x/3x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - J4: 3.3V, RX, GND, TX from SoC side
  - 57600n8
- Power		: 12VDC, 1.5A

Flash instruction using factory image:

1. Boot WRC-2533GHBK-I normally
2. Access to "http://192.168.2.1/" and open firmware update page
   ("ファームウェア更新")
3. Select the OpenWrt factory image and click apply ("適用") button
4. Wait ~150 seconds to complete flashing

MAC addresses:

LAN	: BC:5C:4C:xx:xx:89 (Config, ethaddr (text))
WAN	: BC:5C:4C:xx:xx:88 (Config, wanaddr (text))
2.4GHz	: BC:5C:4C:xx:xx:8A (Factory, 0x4    (hex))
5GHz	: BC:5C:4C:xx:xx:8B (Factory, 0x8004 (hex))

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
2021-01-29 15:32:07 +01:00
Adrian Schmutzler
703fd8aef4 ramips: remove generic profiles
On a platform with many very different devices, like found on ramips,
the generic profiles seem like remnants of the past that do not
have a real use anymore.

Remove them to have one thing less to maintain.

Actually, rt288x didn't have a default profile in the first place.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
2021-01-27 21:31:20 +01:00
Felix Fietkau
ff9846dbb9 ramips: use lzma-loader on zbtlink devices
Fixes boot loader LZMA decompression issues

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-01-27 18:26:53 +01:00
Adrian Schmutzler
f52081bcf9 treewide: provide global default for SUPPORTED_DEVICES
The majority of our targets provide a default value for the variable
SUPPORTED_DEVICES, which is used in images to check against the
compatible on a running device:

  SUPPORTED_DEVICES := $(subst _,$(comma),$(1))

At the moment, this is implemented in the Device/Default block of
the individual targets or even subtargets. However, since we
standardized device names and compatible in the recent past, almost
all targets are following the same scheme now:

  device/image name:  vendor_model
  compatible:         vendor,model

The equal redundant definitions are a symptom of this process.

Consequently, this patch moves the definition to image.mk making it
a global default. For the few targets not using the scheme above,
SUPPORTED_DEVICES will be defined to a different value in
Device/Default anyway, overwriting the default. In other words:
This change is supposed to be cosmetic.

This can be used as a global measure to get the current compatible
with: $(firstword $(SUPPORTED_DEVICES))
(Though this is not precisely an achievement of this commit.)

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-23 12:45:21 +01:00
Bjørn Mork
402408b368 kernel: mtdsplit_uimage: replace "edimax, uimage" parser
The "edimax,uimage"" parser can be replaced by the generic
parser using device specific openwrt,partition-magic and
openwrt,offset properties.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-01-22 21:03:11 +01:00
Bjørn Mork
01a1e21863 kernel: mtdsplit_uimage: replace "openwrt, okli" parser
The only difference between the "openwrt,okli" and the generic
parser is the magic.  Set this in device tree for all affected
devices and  remove the "openwrt,okli" parser.

Tested-by: Michael Pratt <mcpratt@protonmail.com> # EAP300 v2, ENS202EXT and ENH202
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-01-22 21:03:11 +01:00
Bjørn Mork
5ab5bacda2 kernel: mtdsplit_uimage: replace "fonfxc" and "sge" parsers
Convert users of the "fonfxc" and "sge" parsers to the generic
"openwrt,uimage", using device specific "openwrt,padding" properties.

Tested-by: Stijn Segers <foss@volatilesystems.org> [DIR-878 A1]
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-01-22 21:03:11 +01:00
Adrian Schmutzler
b3eccbca7c ramips: fix port labels for Xiaomi Mi Router 4
The OEM assignment of LAN ports is swapped.

Fixes: c2a7bb520a ("ramips: mt7621: add support for Xiaomi Mi Router 4")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-21 22:56:43 +01:00
Dmytro Oz
c2a7bb520a ramips: mt7621: add support for Xiaomi Mi Router 4
Xiaomi Mi Router 4 is the same as Xiaomi Mi Router 3G, except for
the RAM (256Mib→128Mib), LEDs and gpio (MiNet button).

Specifications:

Power: 12 VDC, 1 A
Connector type: barrel
CPU1: MediaTek MT7621A (880 MHz, 4 cores)
FLA1: 128 MiB (ESMT F59L1G81MA)
RAM1: 128 MiB (ESMT M15T1G1664A)
WI1 chip1: MediaTek MT7603EN
WI1 802dot11 protocols: bgn
WI1 MIMO config: 2x2:2
WI1 antenna connector: U.FL
WI2 chip1: MediaTek MT7612EN
WI2 802dot11 protocols: an+ac
WI2 MIMO config: 2x2:2
WI2 antenna connector: U.FL
ETH chip1: MediaTek MT7621A
Switch: MediaTek MT7621A

UART Serial
[o] TX
[o] GND
[o] RX
[ ] VCC - Do not connect it

MAC addresses as verified by OEM firmware:

use   address   source
LAN   *:c2      factory 0xe000 (label)
WAN   *:c3      factory 0xe006
2g    *:c4      factory 0x0000
5g    *:c5      factory 0x8000

Flashing instructions:

1.Create a simple http server (nginx etc)
2.set uart enable
To enable writing to the console, you must reset to factory settings
Then you see uboot boot, press the keyboard 4 button (enter uboot command line)
If it is not successful, repeat the above operation of restoring the factory settings.
After entering the uboot command line, type:

setenv uart_en 1
saveenv
boot

3.use shell in uart
cd /tmp
wget http://"your_computer_ip:80"/openwrt-ramips-mt7621-xiaomi_mir4-squashfs-kernel1.bin
wget http://"your_computer_ip:80"/openwrt-ramips-mt7621-xiaomi_mir4-squashfs-rootfs0.bin
mtd write openwrt-ramips-mt7621-xiaomi_mir4-squashfs-kernel1.bin kernel1
mtd write openwrt-ramips-mt7621-xiaomi_mir4-squashfs-rootfs0.bin rootfs0
nvram set flag_try_sys1_failed=1
nvram commit
reboot
4.login to the router http://192.168.1.1/

Installation via Software exploit
Find the instructions in the https://github.com/acecilia/OpenWRTInvasion

Signed-off-by: Dmytro Oz <sequentiality@gmail.com>
[commit message facelift, rebase onto shared DTSI/common device
definition, bump uboot-envtools]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-21 22:53:19 +01:00
Adrian Schmutzler
93be5926a2 ramips: mt7621: create DTSI for Xiaomi NAND devices
This creates a DTSI for Xiaomi devices with 128M NAND.

This allows to consolidate the partitions and a few other nodes for
AC2100 family and Mi Router 3G.

Note that the Mi Router 3 Pro has 256M NAND and differently sized
partitions.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-21 22:52:02 +01:00
Adrian Schmutzler
5a46b71826 ramips: mt7621: reorganize shared device definitions for Xiaomi
This creates a shared device definition for Xiaomi devices with
NAND and "separate" images, i.e. kernel1.bin and rootfs0.bin.

This allows to consolidate similar/duplicate code for AC2100 family
and Mi Router 3G.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-21 22:52:02 +01:00
Rui Salvaterra
41b096b448 ramips: mt7621: refresh the kernel config
The removed config symbols are already enabled by the generic kernel
configuration (or by default), while the added ones are forcefully
enabled by the specific architecture.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-01-15 19:12:57 +01:00