This backports the following upstream Linux patches
net: sfp: add mode quirk for GPON module Ubiquiti U-Fiber Instant
net: sfp: relax bitrate-derived mode check
net: sfp: cope with SFPs that set both LOS normal and LOS inverted
for 5.4 for mvebu platform.
This fixes GPON modules:
Ubiquiti U-Fiber Instant SFP GPON
VSOL V2801F
CarlitoxxPro CPGOS03-0490 v2.0
Signed-off-by: Marek Behún <marek.behun@nic.cz>
The OCEDO Raccoon had significant packet-loss with cables longer than 50
meter. Disabling EEE restores normal operation.
Also change the ethernet config to reduce loss on sub-1G links.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 4551bfd91f)
Required to allow sysupgrades from OpenWrt 19.07.
Closes#7071
Fixes: 98fbf2edc0 ("ath79: move TPLINK_HWID/_HWREV to parent for tplink-safeloader")
Tested-by: J. Burfeind <git@aiyionpri.me>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
(cherry picked from commit 8ba71f1f6f)
a20-olinuxino-lime2 is currently having hard time with link detection of
certain 1000Mbit partners due to usage of generic PHY driver, probably
due to following missing workaround introduced in upstream in commit
3aed3e2a143c ("net: phy: micrel: add Asym Pause workaround"):
The Micrel KSZ9031 PHY may fail to establish a link when the Asymmetric
Pause capability is set. This issue is described in a Silicon Errata
(DS80000691D or DS80000692D), which advises to always disable the
capability. This patch implements the workaround by defining a KSZ9031
specific get_feature callback to force the Asymmetric Pause capability
bit to be cleared.
This fixes issues where the link would not come up at boot time, or when
the Asym Pause bit was set later on.
As a20-olinuxino-lime2 has Micrel KSZ9031RNXCC-TR Gigabit PHY since
revision H, so we need to use Micrel PHY driver on those devices.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit ffa1088f63)
uDPU has 2 LM75 compatible temperature sensors, so include the driver for
them by default in order to utilize them.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [rebase]
(cherry picked from commit a8b2d35903)
(cherry picked from commit b9e90935db)
uDPU provides a FIT based initramfs, but currently gets stuck after U-boot
starts the kernel at "Starting kernel..".
It is due to the load address being too low, so increase it in order to get
the initramfs booting again.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
(cherry picked from commit 80f21e5336)
(cherry picked from commit d65269a732)
The label has the MAC address of eth0, not the WLAN PHY address.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
(cherry picked from commit 2a02b70499)
This firmware should only be used for mobile devices (e.g. laptops), where
AP mode functionality is typically not used. This firmware supports a lot
of power saving offload functionality at the expense of AP mode support.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit a1ac8728f8)
This is a step forward in adding support for devices with U-Boot.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 34fd5e325a)
This driver is needed to boot from CompactFlash on the Siemens Futro S400.
The device has an AMD NX1500 CPU, which seems to be unsupported by the
geode subtarget, so it must use legacy.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
(cherry picked from commit c8350dfb3c)
1. Create "rootfs_data" dynamicaly
U-Boot firmware images can contain only 2 UBI volumes: bootfs (container
with U-Boot + kernel + DTBs) and rootfs (e.g. squashfs). There is no way
to include "rootfs_data" UBI volume or make firmware file tell U-Boot to
create one.
For that reason "rootfs_data" needs to be created dynamically. Use
preinit script to handle that. Fire it right before "mount_root" one.
2. Relate "rootfs_data" to flashed firmware
As already explained flashing new firmware with U-Boot will do nothing
to the "rootfs_data". It could result in new firmware reusing old
"rootfs_data" overlay UBI volume and its file. Users expect a clean
state after flashing firmware (even if flashing the same one).
Solve that by reading flash counter of running firmware and storing it
in "rootfs_data" UBI volume. Every mismatch will result in wiping old
data.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 93259e8ca2)
This fixes problem with USB PHY not handling some USB 3.0 devices.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 0dbcefdd52)
The following patch was integrated upstream:
target/linux/bcm4908/patches-5.4/180-i2c-brcmstb-fix-support-for-DSL-and-CM-variants.patch
All other updated automatically.
The new config option CONFIG_BPF_UNPRIV_DEFAULT_OFF is now handled too.
Compile-tested on: lantiq/xrx200, armvirt/64
Runtime-tested on: lantiq/xrx200, armvirt/64
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fixes following warning message during image building process:
Finalizing root filesystem...
root-ipq806x/lib/upgrade/asrock.sh: line 1: /lib/functions.sh: No such file or directory
Enabling boot
root-ipq806x/lib/upgrade/asrock.sh: line 1: /lib/functions.sh: No such file or directory
Enabling bootcount
Fixes#9350
Fixes: 98b86296e6 ("ipq806x: add support for ASRock G10")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit fc317a190c)
This reverts commit 13a185bf8a.
There was a report that one A1004ns device fails to detect its flash
chip correctly:
[ 1.470297] spi-nor spi0.0: unrecognized JEDEC id bytes: e0 10 0c 40 10 08
[ 1.484110] spi-nor: probe of spi0.0 failed with error -2
It also uses a different flash chip model:
* in my hand: Winbond W25Q128FVSIG (SOIC-8)
* reported: Macronix MX25L12845EMI-10G (SOP-16)
Reducing spi-max-frequency solved the detection failure. Hence revert.
Reported-by: Koasing <koasing@gmail.com>
Tested-by: Koasing <koasing@gmail.com>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
(cherry picked from commit 9968a909c2)
Fixes following error while executing the init script on the buildhost:
Enabling boot
./etc/init.d/bootcount: line 5: /lib/upgrade/asrock.sh: No such file or directory
Enabling bootcount
While at it fix following shellcheck issue:
base-files/etc/init.d/bootcount line 11:
if [ $? -eq 0 ]; then
^-- SC2181: Check exit code directly with e.g. 'if mycmd;', not indirectly with $?.
Fixes: #9345
Cc: Ansuel Smith <ansuelsmth@gmail.com>
Cc: Pawel Dembicki <paweldembicki@gmail.com>
Cc: Christian Lamparter <chunkeey@gmail.com>
Fixes: 98b86296e6 ("ipq806x: add support for ASRock G10")
References: https://gitlab.com/ynezz/openwrt/-/jobs/1243290743#L1444
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit ce8af0ace0)
It's reported that current memory detection code occasionally detects
larger memory under some bootloaders.
Current memory detection code tests whether address space wraps around
on KSEG0, which is unreliable because it's cached.
Rewrite memory size detection to perform the same test on KSEG1 instead.
While at it, this patch also does the following two things:
1. use a fixed pattern instead of a random function pointer as the magic
value.
2. add an additional memory write and a second comparison as part of the
test to prevent possible smaller memory detection result due to
leftover values in memory.
Fixes: 6d91ddf517 ("ramips: mt7621: add support for memory detection")
Reported-by: Rui Salvaterra <rsalvaterra@gmail.com>
Tested-by: Rui Salvaterra <rsalvaterra@gmail.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
(cherry picked from commit 2f024b7933)
[backport for OpenWrt 21.02 as it was reproducible with Kernel 5.4, see [1]]
[1]: https://forum.openwrt.org/t/113081
Tested-by: Dimitri Souza <dimitri.souza@gmail.com> [mt7621/archer-c6-v3]
Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
The bit position mask was accidentally made too wide, overlapping with the LSB
from the byte position mask. This caused ECC calculation to fail for odd bytes
Signed-off-by: Chad Monroe <chad.monroe@smartrg.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 918d4ab41e)
Many changes were done in drivers/pinctrl/bcm/pinctrl-bcm2835.c between
5.4.171 and 5.4.179.
The following 3 patches do not apply any more:
* target/linux/bcm27xx/patches-5.4/950-0316-pinctrl-bcm2835-Add-support-for-BCM2711-pull-up-func.patch
This was already integrated in kernel v5.4-rc1, it was never needed.
* target/linux/bcm27xx/patches-5.4/950-0328-Revert-pinctrl-bcm2835-Pass-irqchip-when-adding-gpio.patch
* target/linux/bcm27xx/patches-5.4/950-0362-pinctrl-bcm2835-Change-init-order-for-gpio-hogs.patch
I think these were done to fix the problem which was really fixed in
commit 75278f1aff5e ("pinctrl: bcm2835: Change init order for gpio
hogs") from v5.4.175
target/linux/generic/backport-5.4/716-v5.5-net-sfp-move-fwnode-parsing-into-sfp-bus-layer.patch
Move fwnode_device_is_available to the same position as in kernel 5.10.
target/linux/layerscape/patches-5.4/302-dts-0083-arm64-ls1028a-qds-correct-bus-of-rtc.patch
Applied in commit 65816c1034769e714edb70f59a33bc5472d9e55f ("arm64: dts:
ls1028a-qds: move rtc node to the correct i2c bus")
Compile-tested: lantiq/xrx200, bcm27xx/bcm2710
Run-tested: lantiq/xrx200
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Device specifications:
======================
* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/200 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi (11n)
* 2T2R 5 GHz Wi-Fi (11ac)
* 4x GPIO-LEDs (3x wifi, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring
* 2x ethernet
- eth0
+ AR8035 ethernet PHY (RGMII)
+ 10/100/1000 Mbps Ethernet
+ 802.3af POE
+ used as LAN interface
- eth1
+ AR8031 ethernet PHY (RGMII)
+ 10/100/1000 Mbps Ethernet
+ 18-24V passive POE (mode B)
+ used as WAN interface
* 12-24V 1A DC
* internal antennas
This device support is based on the partially working stub from commit
53c474abbd ("ath79: add new OF only target for QCA MIPS silicon").
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
(cherry picked from commit 1699c1dc7f)
All buttons of the FritzBox 7360 family are active-low, not active-high.
Corrent the GPIO flag. This fixes release triggers upon push of a button.
Reported-by: Jan-Niklas Burfeind <git@aiyionpri.me>
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 3154537864)
It was reported that some rb912 boards (ar934x) have issues with some ethernet speeds.
Investigation shows that the board failed to adapt the ethernet pll values as shown here:
[ 5.284359] ag71xx 19000000.eth: failed to read pll-handle property
added custom prints in code and triggering a link switch:
[ 62.821446] Atheros AG71xx: fast reset
[ 62.826442] Atheros AG71xx: update pll 2
[ 62.830494] Atheros AG71xx: no pll regmap!
Comparison with another very similar board (rb922 - QCA955x) showed a missing
reference clock frequency in dts, which seems to cause a pll init issue.
Unfortunately, no errors are printed when this occurs.
Adding the frequency property fixes the pll init as it can be parsed now
by the ethernet driver.
[ 55.861407] Atheros AG71xx: fast reset
[ 55.866403] Atheros AG71xx: update pll 2
[ 55.870462] Atheros AG71xx: ath79_set_pllval: regmap: 0x81548000, pll_reg: 0x2c, pll_val: 0x02000000
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
(cherry picked from commit 2a00054618)
Adds support for GPON SFP modules based on the Realtek RTL8672 and
RTL9601C chips, including but not limited to:
* V-SOL V2801F
* C-Data FD511GX-RM0
* OPTON GP801R
* BAUDCOM BD-1234-SFM
* CPGOS03-0490 v2.0
* Ubiquiti U-Fiber Instant
* EXOT EGS1
Signed-off-by: Vladimir Markovets <abam_a@yahoo.com>
(cherry picked from commit f032601ed7)
The patch
PCI: aardvark: Don't touch PCIe registers if no card connected
was applied into Linux stable version 5.4.163.
Remove it from patches-5.4.
(It applied even though it was applied already, resulting in repeated
code.)
Fixes: 14940aee45 ("kernel: bump 5.4 to 5.4.163")
Signed-off-by: Marek Behún <marek.behun@nic.cz>
This is a requirement for backporting DT files defining such LEDs.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 85ad48c957)
BCM4908 devices with U-Boot use pkgtb firmware format. It's based on
U-Boot's FIT: DTB with configurations, images & embedded data.
This format contains bootfs, rootfs and optionally a first stage U-Boot
loader. Contained images need to be extracted & flashed.
Broadcom used two sets of firmwares: main & backup. It uses UBI volumes
"metadata1" & "metadata2" for storing U-Boot env variables with info
about flashed images.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 5f05795aa7)
This results in setting format specific data (format info, extract
commands) in a single function. It should help maintaining sysupgrade
code.
This change has been tested on Asus GT-AC5300 and Netgear R8000P.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 30b168b9b8)
Fix default network configuration of the Puzzle-M902 so all LAN ports
are included in the LAN bridge.
Setup network LED to indicate WAN port link status, like vendor
firmware does as well.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit f9782f5bcd)
While on Linux 5.10 this fixes Ethernet link status on all ports and
makes 2.5G ports usable in 2.5G and 1G full-duplex mode, when using
Linux 5.4 and backported Aquantia phy patches, only 1G mode works on
the 2.5G ports and link speed and duplex are not reported correctly
from the phy in case of 2.5G.
The reasons are probably trivial, but hard to find. As having all
ports work at least in 1G speed instead of having them not work at
all is still better, push this anyway for now.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit f81a06408e)
Copy and refresh patch enabling AQR112 and AQR412 Ethernet PHY from
layerscape (5.4) target to mvebu (5.4) as AQR112 can also be found
in IEI Puzzle devices.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Wire up MCU driver for LEDs, fan and temperature sensor, and add
GPIO reset button just like on the M902 also on the Puzzle M901.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 3684b494dd)
Add reset button to device tree so it has the function expected from
usual OpenWrt devices.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit ddad936fc6)
Set blinking mode using scheduled work instead of blocking which may
result in deadlocks.
Add dynamic kprintf debugging hexdumps of all MCU rx and tx.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 7e4c1cca8a)
Backport MFD driver for communicating with the on-board MCU found on
IEI World Puzzle appliances.
Improve the driver to support multiple LEDs, apply a default state and
let MCU take care of blinking if timing is within supported range.
Wire up LEDs and fan for Puzzle M902 in device tree.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit f0c0b18234
with commit 962c585580 squashed)
In there linux-firmware repository located in kernel, there were removed old
broadcom firmware [1] as they seem to be likely vulnerable to KrØØk vulnerability
(CVE-2019-15126), because Cypress released new versions and superseded
by it.
In OpenWrt, there is Makefile for cypress-firmware, which already provides
the same named packages like it was in linux-firmware. For example, cypress-firmware-43455-sdio
provides brcmfmac-firmware-43455-sdio [2].
Changelog between 2020118 and 20210315:
3568f96 (tag: 20210315) linux-firmware: Update firmware file for Intel Bluetooth AX210
9e96e50 linux-firmware: Update firmware file for Intel Bluetooth AX200
c8d0db5 linux-firmware: Update firmware file for Intel Bluetooth AX201
5e2a387 Merge tag 'iwlwifi-fw-2021-03-05-v3' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/linux-firmware into main
b0d3e31 rtw88: 8822c: Update normal firmware to v9.9.6
5a2fd63 iwlwifi: add new FWs from core59-66 release
4f54906 iwlwifi: update 9000-family firmwares
11b7607 iwlwifi: update 7265D firmware
e425f76 Merge branch 'add-silabs-wf200' of github.com:jerome-pouiller/linux-firmware into main
5ecd13f Mellanox: Add new mlxsw_spectrum firmware xx.2008.2406
58fb90a linux-firmware: add frimware for mediatek bluetooth chip (MT7921)
e576a1b rtw89: 8852a: add firmware v0.9.12.2
048a7cb WHENCE: add missing symlink for BananaPi M3
aa6c6e7 Add symlink for BananaPi M2 to brcmfmac43430-sdio config
58825f7 brcm: Fix Raspberry Pi 4B NVRAM file
520f71b silabs: add new firmware for WF200
f7915a0 amdgpu: add initial firmware for green sardine
80cb579 rtw88: RTL8822C: Update normal firmware to v9.9.5
b79d239 (tag: 20210208) Merge branch 'DG1-guc-huc-ADLS-dmc' of git://anongit.freedesktop.org/drm/drm-firmware into main
66970e1 Merge branch 'qcom-rb5' of https://github.com/lumag/linux-firmware into main
cf6fc2b Mellanox: Add new mlxsw_spectrum firmware xx.2008.2304
391fd50 linux-firmware: add firmware for MT7921
c5e3240 rtw88: RTL8821C: Update firmware to v24.8
d33d2d8 linux-firmware: Update firmware file for Intel Bluetooth AX210
3027ae4 linux-firmware: Update firmware file for Intel Bluetooth AX200
13979c3 linux-firmware: Update firmware file for Intel Bluetooth AX201
348d8a9 i915: Add DMC v2.01 for ADL-S
f33f1f7 i915: Add HuC v7.7.1 for DG1
6a422f5 i915: Add GuC v49.0.1 for DG1
df822a8 qcom: Add venus firmware files for VPU-1.0
11a1db1 qcom: Add SM8250 Compute DSP firmware
e55248b qcom: Add SM8250 Audio DSP firmware
da74cc6 qcom: add firmware files for Adreno a650
0578970 brcm: Link RPi4's WiFi firmware with DMI machine name.
d528862 brcm: Add NVRAM for Vamrs 96boards Rock960
870b805 brcm: Update Raspberry Pi 3B+/4B NVRAM for downstream changes
a28a590 cypress: Fix link direction
060ad8b cypress: Link the new cypress firmware to the old brcm files
0f0aefd brcm: remove old brcm firmwares that have newer cypress variants
f580dc2 rtl_bt: Update RTL8822C BT(UART I/F) FW to 0x059A_25CB
7df2220 rtl_bt: Update RTL8822C BT(USB I/F) FW to 0x099a_7253
e79405d rtl_bt: Add firmware and config files for RTL8852A BT USB chip
ef3813d rtl_bt: Update RTL8821C BT(USB I/F) FW to 0x829a_7644
646f159 (tag: 20201218) make AP6212 in bananpi m2 plus/zero work
28185ec linux-firmware: Update firmware file for Intel Bluetooth AX210
23da869 linux-firmware: Update firmware file for Intel Bluetooth AX200
2099248 linux-firmware: Update firmware file for Intel Bluetooth AX201
94de5e2 linux-firmware: Update firmware file for Intel Bluetooth 9560
27a3689 linux-firmware: Update firmware file for Intel Bluetooth 9260
5c3c4af Merge branch 'lt9611uxc' of https://github.com/lumag/linux-firmware into main
aaed4a8 Merge branch 'v1.1.6' of https://github.com/irui-wang/linux_fw_vpu_v1.1.6 into main
d8c9865 Merge branch 'master' of https://github.com/sampnimm/linux-firmware-BT into main
63ab3db linux-firmware: add firmware for Lontium LT9611UXC DSI to HDMI bridge
0fe0fe0 mediatek: update MT8173 VPU firmware to v1.1.6
1a08ec9 QCA : Updated firmware files for WCN3991
7455a36 Merge branch 'guc_v49' of git://anongit.freedesktop.org/drm/drm-firmware into main
7eb7fda linux-firmware: Update firmware file for Intel Bluetooth AX210
5cbf459 linux-firmware: Update firmware file for Intel Bluetooth AX210
c487f7d i915: Add GuC firmware v49.0.1 for all platforms
d9ffb07 i915: Remove duplicate KBL DMC entry
b362fd4 Mellanox: Add new mlxsw_spectrum firmware xx.2008.2018
bc9cd0b linux-firmware: Update AMD SEV firmware
54c797a amdgpu: add sienna cichlid firmware for 20.45
1340e9c amdgpu: update vega20 firmware for 20.45
b260c9c amdgpu: update vega12 firmware for 20.45
d683bd5 amdgpu: update vega10 firmware for 20.45
7c81cc2 amdgpu: update renoir firmware for 20.45
3619e57 amdgpu: update navi14 firmware for 20.45
68ce0fb amdgpu: update navi12 firmware for 20.45
e889b80 amdgpu: update navi10 firmware for 20.45
f4edc15 amdgpu: update raven2 firmware for 20.45
e71210f amdgpu: update raven firmware for 20.45
[1] https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git/commit/?id=0f0aefd733f70beae4c0246edbd2c158d5ce974c
[2] eeda8652f1/package/firmware/cypress-firmware/Makefile (L124)
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
(cherry picked from commit ff2bb16730)
(removed sinovoip_bananapi-m2-berry)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Follow the recommendations stated in the Turris Omnia DTS for eth2:
"In case SFP module is present, U-Boot has to enable the sfp node above,
remove phy-handle property, and add managed = "in-band-status" property."
The boot script is written in a way, that it works for all U-Boot
versions deployed by the vendor so far (2015.10-rc2, 2019.07).
Reviewed-by: Noci <noci@noci.work>
Reviewed-by: Justin van Steijn <jvs@fsfe.org>
Reviewed-by: Nico Rikken <nico@nicorikken.eu>
Reviewed-by: Julius Schwartzenberg <julius.schwartzenberg@gmail.com>
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
(cherry picked from commit 23d2690e5a5410576b587bc96e2c2cf5fc693927)
Kernel 5.4 receives a reduced set, just to make the SFP cage work.
While we are at it, move the patches accepted upstream to the 0xx series.
Reviewed-by: Noci <noci@noci.work>
Reviewed-by: Justin van Steijn <jvs@fsfe.org>
Reviewed-by: Nico Rikken <nico@nicorikken.eu>
Reviewed-by: Julius Schwartzenberg <julius.schwartzenberg@gmail.com>
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
(cherry picked from commit 8138cb8737d1475e6e8d57393500f30384e75a82)
