In ramips, all devices in mt7621, mt76x8 and rt288x subtarget have
the same value set to the SOC variable for each device individually.
This patch introduces a non-device-dependent variable DEFAULT_SOC,
which is used if no specific SOC is set for a device, and thus reduces
the number of redundant definitions drastically.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Based on a script for comparison, this fixes (hopefully) all errors
in SUPPORTED_DEVICES for ar71xx->ath79 upgrade.
Devices where old string is removed as the device does not exist
in ar71xx:
- dlink_dir-859-a1
- tplink_archer-a7-v5
- tplink_cpe510-v3
Devices where string is changed because it did not match the board
name in ar71xx:
- tplink_tl-mr3220-v1
- tplink_tl-mr3420-v1
- tplink_tl-wr2543-v1
- tplink_tl-wr741nd-v4
- tplink_tl-wr841-v7
- ubnt_unifiac-mesh
- ubnt_unifiac-mesh-pro
- ubnt_unifiac-pro
For this device, the correct string could not be found, but we could
not determine the correct one. Thus, the string is removed for now:
- tplink_tl-wr740n-v4
The script for checking this is quite simple (note that newer
entries, i.e. ath79->ath79 upgrade, are displayed as missing):
newpath=target/linux/ath79/image/
oldpath=target/linux/ar71xx/base-files/lib/ar71xx.sh
for s in $(grep -roh "SUPPORTED_DEVICES.*" $newpath | sed 's/SUPPORTED_DEVICES *.= *//'); do
found="Missing"
grep -q -r "\"$s\"" $oldpath && found="Found"
echo "$s: $found."
done
The errors might be filtered by appending 'grep "Missing"' to the script.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In certain cases, the uncompressed initramfs image will overwrite
the lzma-loader, which is currently only 10 MB away from kernel image
start. To prevent this, change LZMA_TEXT_START to 24 MB, so loader
and compressed image have 8 MB at the end of RAM and uncompressed
image has 24 MB available.
This is only enabled for ath79 at the moment, as there we can be sure
that all devices have 32+ MB RAM and TARGET_INITRAMFS_COMPRESSION_LZMA
is not enabled there.
Despite, since lzma-loader is currently build specifically for ath79
anyway, there is no need to re-specify LOADADDR and LZMA_TEXT_START
in image/Makefile, so the values are set directly in
image/lzma-loader/Makefile and the overwrite in image/Makefile is
removed.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This commit adds support for the MikroTik RouterBOARD wAP G-5HacT2HnD
(wAP AC), a small weatherproof dual band, dual-radio 802.11ac
wireless AP with integrated omnidirectional anntennae and one
10/100/1000 Mbps Ethernet port.
See https://mikrotik.com/product/RBwAPG-5HacT2HnD for more info.
Specifications:
- SoC: Qualcomm Atheros QCA9556
- RAM: 64 MB
- Storage: 16 MB NOR
- Wireless:
· Atheros AR9550 (SoC) 802.11b/g/n 2x2:2, 2 dBi antennae
· Qualcomm QCA9880 802.11a/n/ac 3x3:3, 2 dBi antennae
- Ethernet: Atheros AG71xx (SoC, AR8033), 1x 1000/100/10 port,
passive PoE in
Working:
- Board/system detection
- Sysupgrade
- Serial console
- Ethernet
- 2.4 GHz radio
- 5 GHz radio and LED
- Reset button
Not working/Unsupported:
- 2.4 GHz LED
- AP/CAP LED
- ZT2046Q SPI temperature and voltage sensor
This adds the basic features for supporting MikroTik devices:
- a common recipe for mikrotik images in common-mikrotik.mk
- support for minor (MikroTik NOR) split firmware (only for
generic subtarget so far)
Acknowledgments: Robert Marko <robimarko@gmail.com>
Andrew Cameron <apcameron@softhome.net>
Koen Vandeputte <koen.vandeputte@ncentric.com>
Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Co-developed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
In order to make the QCA955x SGMII workaround work, the unsuccessful
SGMII autonegotiation on the AR8033 should not block the PHY
state-machine.
Otherwise, the ag71xx driver never becomes aware of the copper-side
link-establishment and the workaround is never executed.
Signed-off-by: David Bauer <mail@david-bauer.net>
[remove one trailing whitespace per file]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit adds a workaround for the loss of the SGMII link observed on
the QCA955x generation of SoCs. The workaround originates part from the
U-Boot source code, part from the implementation from AVM found in the
GPL tarball for the AVM FRITZ!WLAN Repeater 450E.
The bug results in a stuck SGMII link between the PHY device and the SoC
side. This has only been observed with the Atheros AR8033 PHY and most
likely all devices using such combination are affected.
It is worked around by reading a hidden SGMII status register and
issuing a SGMII PHY reset until the link becomes useable again.
Signed-off-by: David Bauer <mail@david-bauer.net>
Due to the history of the target, all devices added before a certain
point have the same device string in BOARD_NAME, DEVICE_DTS and added
to SUPPORTED_DEVICES.
Thus, we can set this one automatically for all devices where
BOARD_NAME is specified, removing the explicit DEVICE_DTS and
SUPPORTED_DEVICES addition there.
For new devices, nothing has changed, and just DEVICE_DTS has to
be set manually.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This tidies up the image Makefiles for the sunxi target by:
- Move the if-condition for the subtarget to the parent Makefile
- Remove lots of unnecessary empty lines
- Sort device definitions alphabetically
- Harmonize line wrapping for DEVICE_PACKAGES
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Change u-boot-env partitions to be mounted as read-write for gl-ar150,
gl-domino and gl-mifi so uboot-envtools support is possible.
Signed-off-by: Kimmo Vuorinen <kimmo.vuorinen@gmail.com>
[commit title/message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link TL-WA850RE v2 is a wall-plug N300 Wi-Fi range extender,
based on Qualcomm/Atheros QCA9533 v2.
Short specification:
- 550/391/195 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 32 MB of RAM (DDR1)
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 2x internal antennas (embedded on PCB)
- 9x LED (all can be turned off with GPIO15), 2x button
- UART (J3) header on PCB
Flash instruction: use "factory" image directly in vendor GUI.
Warning: this device does not include any kind of recovery mechanism
in the bootloader and disassembling process is not trivial.
You can access vendor firmware over serial line using:
- login: root
- password: sohoadmin
Stock firmware uses label MAC address for WiFi and same with local
bit set for ethernet. Since this is difficult to reproduce with
the toolset of OpenWrt, we just keep both ethernet and WiFi to
the same address here.
This is the first tiny device with tplink-safeloader in ath79.
Firmware partition is only 3648k and thus even smaller than for
the tplink-4m(lzma) devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This moves the TP-Link TL-WA850RE v2 to dynamic partitioning and
will allow to use this for ath79 as well.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
- Remove the "RGMII TX delay fixup" hack and the associated
DT-property. It was never used in a DT-based platform and
solved a problem which can be mitigated by using correct
delays on the MAC side.
- Remove the patch to enable platform-data support for the
at803x driver. It was only used by ar71xx which does not
(and never will) support kernel 4.19 or later.
- Remove the SmartEEE DT-configuration patch. As explained
previously, this patch never disabled the Atheros SmartEEE
implementation, but rather "standard" EEE. This can be done
on device-tree compatible platforms by adding the
"eee-broken-1000t" or "eee-broken-100tx" properties to the PHY
node. As all usages of the old properties are migrated, this
patch can be removed.
Signed-off-by: David Bauer <mail@david-bauer.net>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
The hack-patch which introduced the "at803x-disable-smarteee" for
disabling SmartEEE did in fact not disable SmartEEE but rather disabled
802.3az "standard" EEE.
This can be done by using the upstream properties "eee-broken-100tx" and
"eee-broken-1000t". EEE is then disabled by the PHY subsystem.
Tested on devolo WiFi pro 1200e.
Signed-off-by: David Bauer <mail@david-bauer.net>
This ports support for the TL-WA850RE v1 range extender from ar71xx
to ath79.
Specifications:
Board: AP123 / AR9341 rev. 3
Flash/RAM: 4/32 MiB
CPU: 535 MHz
WiFi: 2.4 GHz b/g/n
Ethernet: 1 port (100M)
Flashing instructions:
Upload the factory image via the vendor firmware upgrade option.
Recovery:
Note that this device does not provide TFTP via ethernet like many
other TP-Link devices do. You will have to open the case if you
require recovery beyond failsafe.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Add patches retrying to probe the PHY to restore support for PHYs taking
longer to initialize without breaking modules without PHYs.
Patches taken from http://git.armlinux.org.uk/cgit/linux-arm.git/log/?h=phy
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Update the uDPU kernel support, fixing a number of issues:
* make ethernet work again by adding comphy definitions
* slow the I2C bus to give it more chance of actually working
* the SFP cages are designed to support up to 3W modules, which
would be prevented from initialising without this patch.
Signed-off-by: Russell King <linux@armlinux.org.uk>
[jonas.gorski: rename to mvebu, refresh patches]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Add support for Methode DM7052 NBASE-T module to OpenWRT. These
patches are taken from my "phy" branch, and will be sent for the
next kernel merge window.
Signed-off-by: Russell King <linux@armlinux.org.uk>
[jonas.gorski: move patches to pending, refresh patches]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Backport the phy/phylink/sfp patches currently queued in netdev or in
mainline necessary to support GPON popular modules, specifically to
support Huawei and Nokia GPON modules.
Signed-off-by: Russell King <linux@armlinux.org.uk>
[jonas.gorski: include kernel version in file names, refresh patches]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Move two phylink patches from mvebu to generic, so that everyone can
benefit from them.
Signed-off-by: Russell King <linux@armlinux.org.uk>
[jonas.gorski: add kernel version to file names]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Remove the old phylink/SFP patches from the OpenWRT build; these will
be updated with a new set in subsequent.
450-reprobe_sfp_phy is also removed for several reasons:
1) it is not in mainline.
2) it breaks copper modules that do not have a PHY.
3) it makes backporting the current patch set harder.
Discussion is ongoing with the patch author for a mainline Linux kernel
patch for this.
Signed-off-by: Russell King <linux@armlinux.org.uk>
TPLINK_BOARD_NAME has been renamed to TPLINK_BOARD_ID a long time
ago (7d6c63d875: "build: rename TPLINK_BOARD_NAME to
TPLINK_BOARD_ID" for ar71xx), and before introducing ath79 target
at all.
TPLINK_BOARD_NAME seems to have been introduced into ath79 target
only by mistake. It has never been used. Remove it.
Fixes: 53c474abbd ("ath79: add new OF only target for QCA MIPS silicon")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This reverts commit de80424f70 which needs
more work and testing as it broke at least jffs2 overlays at least on
ath79 platform, marking them as read-only, thus unusable:
jffs2_build_filesystem(): erasing all blocks after the end marker...
jffs2: Erase at 0x009e0000 failed immediately: -EROFS. Is the sector locked?
Ref: http://lists.infradead.org/pipermail/openwrt-devel/2020-January/021344.html
Reported-by: Steve Brown <sbrown@ewol.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
In zynq target, the DEVICE_DTS variable is always set consistent
with the model part of the device definition name.
This patch replaces the redundant definitions for the individual
devices with a common recipe.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
For the mvebu target in particular, there is a lot of files in
base-files that are only relevant for one subtarget. Improve
overview and reduce size per subtarget by moving/splitting
base-files depending on the subtarget they belong to.
While at it, consolidate 01_leds by using the model part of
the board name as variable.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This introduces the SOC variable to mvebu target to derive some of
the DEVICE_DTS variables based on the SOC prefix and the device
definition name.
Since DTS names and compatible are inconsistent also in the kernel
for this target, the scheme cannot be applied to all devices, though.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This moves the if conditions for choosing which image Makefiles
are used to the parent image/Makefile. It seems more convenient
to have "codeflow" in the parent while the subtarget-specific
files only contain the definitions.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This device is an LTE router supported in ar71xx so far.
As per original commit, hardware specifications (v1.0 EU):
- SoC: QCA9531
- Flash: Winbond W25Q64FV (8MiB)
- RAM: EtronTech EM6AB160TSE-5G (64MiB)
- Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna)
- Ethernet: 2NIC (3x100M + 1x100M)
- WWAN: TP-LINK LTE MODULE (2x external detachable antenna)
- Power: DC 12V 1A
Flashing instructions:
You can flash via tftp recovery (serve factory image as /mr6400_tp_recovery.bin
on 192.168.0.66/24, connect to any ethernet port and power on device while
holding the reset button). Flashing via OEM web interface does not work.
Known issues:
- LTE module does not always come up during boot (showing USB enumeration errors). Similar behavior has been reported at least from one user for ar71xx, too. Turning USB off and on again will serve as a workaround.
- eth0 (LAN) always shows carrier as 1 even if no cable is plugged in (this works "correctly" on ar71xx)
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
[several adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Filip Moc <lede@moc6.cz>
When mapping for RSSI LEDs was defined for interface wlan0 on
Ubiquiti Rocket M Titanium, it missed connection to actual interface.
Therefore create the mapping to interface, so RSSI LEDs work without
additional configuration, after starting rssileds service.
While at that, split RSSI into ~equal intervals for 6 LEDs,
and remove coefficients needed for PWM LEDs, as this board does not
support PWM LEDs.
Finally, for complete support, enable 'rssileds' package in per-device
rootfs, so the indicator works out of box.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Kernel partition increase to 4 MiBs for Netgear WNDR3700v4 and WNDR4300
routers breaks sysupgrade image compatibility with ar71xx builds.
Therefore, SUPPORTED_DEVICES variable has to be removed for both devices
from target makefile.
Reported-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Currently it's not possible to effectively mark a "firmware" partition
as read-only. The sub-partitions "kernel", "rootfs" and "rootfs_data"
are always created as read-write (ignoring the parent access mode).
This patch enforces the access mode of sub-partitions to match the
parent partition, which is useful for recovery images that are meant
to be fully read-only to avoid accidental damage from end-user.
An example of such implementation (read-only firmware image) is the
recovery image used on the Zsun-SD100 [1].
Please note the related patch for fstools [2] to enable this read-only
concept.
[1] https://github.com/brunompena/zsun-resources
[2] http://lists.infradead.org/pipermail/openwrt-devel/2020-January/021043.html
Signed-off-by: Bruno Pena <brunompena@gmail.com>
[removed already obsolete 4.9 kernel patch]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The Netgear WN2500RP V1 switch0 already works for LAN
however the port order for the LAN ports is inverted. Correct
physical port order watched from the back of the device is:
4 / 3 / 2 / 1
WAN port is absent on this device and therefore removed
from switch config.
Signed-off-by: Walter Sonius <walterav1984@gmail.com>
[move block to maintain alphabetic sorting]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The device tree property "mediatek,led_polarity" is ignored for
MT7628AN and MT7688. According to the datasheet both SoCs have
the matching register. Therefore the property should be applied
on these two devices as well.
Signed-off-by: Maximilian Pachl <m@ximilian.info>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
Tested-by: Sungbo Eo <mans0n@gorani.run>
Change the LED labels for hdd1/hdd2 in 01_leds to match their
counterpart in DTS.
Signed-off-by: Stephan Knauss <openwrt@stephans-server.de>
[improve commit title and message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The Netgear WNR3500 V2 switch0 already works for WAN/LAN
however the port order for the LAN ports is inverted. Correct
physical port order watched from the back of the device is:
Internet / 4 / 3 / 2 / 1 this resembles the Linksys E3000 V1.
Verfied with imagebuilder edit FILES=/etc/board.d/01_network
Signed-off-by: Walter Sonius <walterav1984@gmail.com>
Specification:
SoC: MediaTek MT7628AN
RAM: 64MiB
Flash: 8MiB
Wifi:
- 2.4GHz: MT7628AN
- 5GHz: MT7612EN
LAN: 1x 10/100 Mbps
Flash instructions:
Flash factory image through stock firmware WEB UI.
Back to stock is possible by using TFTP and stripping down the Firmware
provided by TP-Link to a initramfs.
The flash space between 0x650000 and 0x7f0000
is blank in the stock firmware so I left it out as well.
Signed-off-by: Steffen Förster <nemesis@chemnitz.freifunk.net>
Most of the kernel version switches below 4.14 were removed in commit
97940f8766 ("kernel: remove obsolete kernel version switches"),
but some of them still remained. Remove them now.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Using the led_ prefix for the node label is now common in ath79,
so also apply it here.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Using the LED of network interfaces for status (boot/failsafe/...)
indication is somewhat misleading, as the blinking might be
mistaken for network activity. This uses rssi LEDs instead, which
do not blink normally and thus are less ambiguous.
The rssihigh LED has also been used consistently for the TP-Link CPE
devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
"#mediatek,portmap" is not a valid property name.
If mediatek,portmap equals 0x0, then the esw driver ditches it and uses
the default value, 0x3f.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
mt76x8 uses esw_rt3050 driver, which does not accept mediatek,portmap with
string values. Convert the strings to integers to make it work.
According to its switch setup, WRTnode 2P/2R have a WAN port at port 0,
so the correct value should be 0x3e.
tplink_8m.dtsi uses "llllw", but it does not match switch setups of any
device using the DTSI. Remove it from the DTSI and add correct value to DTS
for each device.
These devices have a WAN port at port 0. Set the value to 0x3e.
- tplink,archer-c20-v4
- tplink,archer-c50-v3
- tplink,tl-mr3420-v5
- tplink,tl-wr840n-v4
- tplink,tl-wr841n-v13
- tplink,tl-wr842n-v5
These devices have only one ethernet port. They don't need portmap setting.
- tplink,tl-wa801nd-v5
- tplink,tl-wr802n-v4
- tplink,tl-wr902ac-v3
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
mt7620 and mt7621 use mt7530 driver, which only accepts "llllw", "wllll",
and "lwlll" values.
According to its switch setup, Mi Router 3G v2 has a WAN port at port 4,
so the correct value should be "llllw".
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
- fix color and active mode for existing wps led
- add green wps led
- add wps button
Signed-off-by: Jan Alexander <jan@nalx.net>
[wrap line]
Signed-off-by: David Bauer <mail@david-bauer.net>
Do not put usb-phy into reset if clearing the usb-phy reset or
setting the suspend_override has failed.
Reorder (de)asserts like in arch/mips/ath79/dev-usb.c.
Add an optional reset_control "usb-phy-analog", which is needed for
ar934x SoCs like in the old mach-driver arch/mips/ath79/dev-usb.c.
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
This image is only needed on one device (wAP AC); since this target is
going to be removed anyway it doesn't make sense to add an extra "low
RAM" image.
Fixes OOM issues on RouterBoard wAP AC.
Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
Change the caldata partition DTS node label to be consistent with
the label property for some Netgear WNDR devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch introduces support for Netgear WNDR4500v3. Router
is very similar to WNDR4300v2 and is based on the same PCB.
Information gathered from various Internet sources (including
https://patchwork.ozlabs.org/patch/809227/) shows following
differences to WNDR4300v2:
* two USB 2.0 ports with separate LEDs
* USB LEDs soldered to secondary pads
* WPS and RFKILL buttons soldered to secondary pads
* described as N900 device with 3x3:3 MIMO for 2.4GHz radio
* power supply requirement is DC 12V 2.5A
* vendor HW ID suffix differs in one digit
* bigger chassis
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
This patch introduces support for Netgear WNDR4300v2.
Specification
=============
* Description: Netgear WNDR4300 v2
* Loader: U-boot
* SOC: Qualcomm Atheros QCA9563 (775 MHz)
* RAM: 128 MiB
* Flash: 2 MiB SPI-NOR + 128 MiB SPI-NAND
- NOR: U-boot binary: 256 KiB
- NOR: U-boot environment: 64 KiB
- NOR: ART Backup: 64 KiB
- NOR: Config: 64 KiB
- NOR: Traffic Meter: 64 KiB
- NOR: POT: 64 KiB
- NOR: Reserved: 1408 KiB
- NOR: ART: 64 KiB
- NAND: Firmware: 25600 KiB (see notes for OpenWrt)
- NAND: Language: 2048 KiB
- NAND: mtdoops Crash Dump: 128 KiB
- NAND: Reserved: 103296 KiB
* Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN) (AR8337)
* Wireless:
- 2.4 GHz b/g/n (internal)
- 5 GHz a/n (AR9580)
* USB: yes, 1 x USB 2.0
* Buttons:
- Reset
- WiFi (rfkill)
- WPS
* LEDs:
- Power (amber/green)
- WAN (amber/green)
- WLAN 2G (green)
- WLAN 5G (blue)
- 4 x LAN (amber/green)
- USB (green)
- WPS (green)
* UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1
* Power supply: DC 12V 1.5A
* MAC addresses: LAN=WLAN2G on case label, WAN +1, WLAN5G +2
Important Notes
===============
0. NOR Flash (2 MiB) is not touched by OpenWrt installation.
1. NAND Flash (128 MiB) layout under OpenWrt is changed as follows:
all space is split between 4 MiB kernel and 124 MiB UBI areas;
vendor partitions (language and mtdoops) are removed; kernel space
size can be further expanded if needed; maximum image size is set
to 25600k for compatibility reasons and can also be increased.
2. CPU clock is 775 MHz, not 750 MHz.
3. 5 GHz wireless radio chip is Atheros AR9580-AR1A with bogus PCI
device ID 0xabcd. For ath9k driver to load successfully, this is
overriden in DTS with correct value for this chip, 0x0033.
4. RFKILL button is wired to AR9580 pin 9 which is normally disabled
by chip definition in ath9k code (0x0000F4FF gpio mask). Therefore
'qca,gpio-mask=<0xf6ff>' hack must be used for button to work
properly.
5. USB port is always on, no GPIO for 5V power control has been
identified.
Installation
============
* TFTP recovery
* TFTP via U-boot prompt
* sysupgrade
* Web interface
Test build configuration
========================
CONFIG_TARGET_ath79=y
CONFIG_TARGET_ath79_nand=y
CONFIG_TARGET_ath79_nand_DEVICE_netgear_wndr4300-v2=y
CONFIG_ALL_KMODS=y
CONFIG_DEVEL=y
CONFIG_CCACHE=y
CONFIG_COLLECT_KERNEL_DEBUG=y
CONFIG_IMAGEOPT=y
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
This commit adds support for the D-Link DIR-505, previously supported in
ar71xx.
Hardware
--------
SoC: Atheros AR9330
FLASH: 8M SPI-NOR
RAM: 64M
WIFI: 1T1R 1SS Atheros AR9330
LED: Power green, Status red
BTN: WPS, Reset
Installation
------------
Currently, installation is only possible by sysupgrading from an earlier
OpenWrt version, U-Boot TFTP or a modded U-Boot. I do not have the
original bootloader from D-Link on my device anymore, so i cannot test
the factory image.
Signed-off-by: David Bauer <mail@david-bauer.net>
The present U-Boot for GL-AR750S has a limit of 2 MB for kernel size.
While sysupgrade can manage kernels up to the present limit of 4 MB,
directly flashing a factory.img with a kernel size greater than 2 MB
through U-Boot will result in an unbootable device.
This commit uses the newly-introduced check-kernel-size build
operation to prevent the output of factory.img when the kernel
exceeds 2 MB in size, yet permits output of sysupgrade.img
as long as the kernel is within KERNEL_SIZE := 4096k
Cc: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
The memory hacks got removed from ath10k with 1e27bef ("mac80211: remove
ath10k_pci memory hacks"). As this device has low amount of RAM, switch
to ath-10k-ct small buffers variant, to avoid the OOM Reaper.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This reorganizes 02_network board.d files based on what's done for
ath79 and ramips: Instead of putting all settings into a single big
case, the interface/dsl/MAC address setup is put into separate
functions with a specific switch case for each of them. This makes
grouping of devices much easier and should be easier to read, too.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
DSL setup consists of the same commands for all subtargets, so move it
into a helper function.
While at it, remove shebang from library file.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This splits the device-dependent base-files into subtarget directories,
like done recently for ath79 and ramips. While this increases the
overall lines of codes, it will make the code per subtarget smaller
and easier to keep track of features and devices.
While at it, several variables at the top of 02_network are removed,
as they were never changed. The values are put directly into the
function calls where they are used.
Remove unneeded LED setup from 01_leds, and remove 01_leds entirely
for falcon subtarget (as it is not used there).
Applies alphabetic reordering to device cases in base-files.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This splits some base-files across subtargets, as done previously
on ath79 and ramips and also introduced for mt7629 subtarget here
already. Most of the existing base-files content is specific to
mt7623.
While at it, apply the following fixes:
- Remove lots of trailing whitespaces
- Remove wildcard on unielec,u7623-02-emmc-512m
- Remove inconsistent quotation marks in cases
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: John Crispin <john@phrozen.org>
The Aruba AP-303H is the hospitality version of the Aruba AP-303 with a
POE-passthrough enabled ethernet switch instead of a sigle PHY.
Hardware
--------
SoC: Qualcomm IPQ4029
RAM: 512M DDR3
FLASH: - 128MB SPI-NAND (Macronix)
- 4MB SPI-NOR (Macronix MX25R3235F)
TPM: Atmel AT97SC3203
BLE: Texas Instruments CC2540T
attached to ttyMSM1
ETH: Qualcomm QCA8075
LED: WiFi (amber / green)
System (red / green /amber)
PSE (green)
BTN: Reset
USB: USB 2.0
To connect to the serial console, you can solder to the labled pads next
to the USB port or use your Aruba supplied UARt adapter.
Do NOT plug a standard USB cable into the Console labled USB-port!
Aruba/HPE simply put UART on the micro-USB pins. You can solder yourself
an adapter cable:
VCC - NC
D+ - TX
D- - RX
GND - GND
The console setting in bootloader and OS is 9600 8N1. Voltage level is
3.3V.
To enable a full list of commands in the U-Boot "help" command, execute
the literal "diag" command.
Installation
------------
1. Get the OpenWrt initramfs image. Rename it to ipq40xx.ari and put it
into the TFTP server root directory. Configure the TFTP server to
be reachable at 192.168.1.75/24. Connect the machine running the TFTP
server to the E0 (!) ethernet port of the access point, as it only
tries to pull from the WAN port.
2. Connect to the serial console. Interrupt autobooting by pressing
Enter when prompted.
3. Configure the bootargs and bootcmd for OpenWrt.
$ setenv bootargs_openwrt "setenv bootargs console=ttyMSM0,9600n8"
$ setenv nandboot_openwrt "run bootargs_openwrt; ubi part aos1;
ubi read 0x85000000 kernel; set fdt_high 0x87000000;
bootm 0x85000000"
$ setenv ramboot_openwrt "run bootargs_openwrt;
setenv ipaddr 192.168.1.105; setenv serverip 192.168.1.75;
netget; set fdt_high 0x87000000; bootm"
$ setenv bootcmd "run nandboot_openwrt"
$ saveenv
4. Load OpenWrt into RAM:
$ run ramboot_openwrt
5. After OpenWrt booted, transfer the OpenWrt sysupgrade image to the
/tmp folder on the device. You will need to plug into E1-E3 ports of
the access point to reach OpenWrt, as E0 is the WAN port of the
device.
6. Flash OpenWrt:
$ ubidetach -p /dev/mtd16
$ ubiformat /dev/mtd16
$ sysupgrade -n /tmp/openwrt-sysupgrade.bin
To go back to the stock firmware, simply reset the bootcmd in the
bootloader to the original value:
$ setenv bootcmd "boot"
$ saveenv
Signed-off-by: David Bauer <mail@david-bauer.net>
The Ubiquiti ToughSwitch 5XP is a 5-port PoE Gigabit switch with a single
Fast-Ethernet management port. It supports both 24V passive PoE out on all
five ports.
Flash: 8 MB
RAM: 64 MB
SoC: AR7242
Switch: ar8327
USB: 1x USB 2.0
Ethernet: 5x GbE, 1x FE
Installation of the firmware is possible either via serial + tftpboot or
the factory firmware update function via webinterface.
By default the single Fast-Ethernet port labeled "MGMT" is configured
as the WAN port. Thus access to the device is only possible via the
five switch ports.
Serial: 3v3 115200 8n1
The serial header is located in the lower left corner of the switches PCB:
```
|
|
|
| o
| o RX
| o TX
| o GND
|
|
++ +-++-+ ++ ++ +
+--+ ++ +--++--++--+
```
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
[remove ubnt,sw compatible - fix spelling - wrap commit message -
remove superfluous phy-mode property]
Signed-off-by: David Bauer <mail@david-bauer.net>
This device OOPs during the boot due to broken flash. It can be probably
fixed with `broken-flash-reset` once ramips is on 4.19 kernel.
So disable images for this device until its fixed.
Ref: FS#2695, PR#2483
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Builds for kenrel 4.14 targetswere failing because of
missing symbols for the B53 swconfig driver.
Fixes: 313bde53ce ("generic: update config-4.19")
Signed-off-by: David Bauer <mail@david-bauer.net>
Hardware:
SOC: Qualcomm IPQ4018
RAM: 128 MB Nanya NT5CC64M16GP-DI
FLASH: 16 MB Macronix MX25L12805D
ETH: Qualcomm QCA8075 (4 Gigabit ports, 3xLAN, 1xWAN)
WLAN: Qualcomm IPQ4018 (2.4 & 5 Ghz)
BUTTON: Shared WPS/Reset button
LED: RGB Status/Power LED
SERIAL: Header J8 (UART, Left side of board). Numbered from
top to bottom:
(1) GND, (2) TX, (3) RX, (4) VCC (White triangle
next to it).
3.3v, 115200, 8N1
Tested/Working:
* Ethernet
* WiFi (2.4 and 5GHz)
* Status LED
* Reset Button (See note below)
Implementation notes:
* The shared WPS/Reset button is implemented as a Reset button
* I could not find a original firmware image to reverse engineer, meaning
currently it's not possible to flash OpenWrt through the Web GUI.
Installation (Through Serial console & TFTP):
1. Set your PC to fixed IP 192.168.1.12, Netmask 255.255.255.0, and connect to
one of the LAN ports
2. Rename the initramfs image to 'C0A8010B.img' and enable a TFTP server on
your pc, to serve the image
2. Connect to the router through serial (See connection properties above)
3. Hit a key during startup, to pause startup
4. type `setenv serverip 192.168.1.12`, to set the tftp server address
5. type `tftpboot`, to load the image from the laptop through tftp
6. type `bootm` to run the loaded image from memory
6. (If you want to return to stock firmware later, create an full MTD backup,
e.g. using instructions here https://openwrt.org/docs/guide-user/installation/generic.backup#create_full_mtd_backup)
7. Transfer the 'sysupgrade' OpenWrt firmware image from PC to router, e.g.:
`scp xxx-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/upgrade.bin`
8. Run sysupgrade to permanently install OpenWrt to flash: `sysupgrade -n /tmp/upgrade.bin`
Revert to stock:
To revert to stock, you need the MTD backup from step 6 above:
1. Unpack the MTD backup archive
2. Transfer the 'firmware' partition image to the router (e.g. mtd8_firmware.backup)
3. On the router, do `mtd write mtd8_firmware.backup firmware`
Signed-off-by: Tom Brouwer <tombrouwer@outlook.com>
[removed BOARD_NAME, OpenWRT->OpenWrt, changed LED device name to board name]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch partially reverts
"ipq40xx: remove unnecessary usb nodes in DTS for ASUS RT-AC58U"
as the change removed the usb2 port-trigger, so the LED would no
longer light-up when a USB 2.0 was inserted into the USB port.
Fixes: d0efb1ba95 ("ipq40xx: remove unnecessary usb nodes in DTS for ASUS RT-AC58U")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Flash: 8 MB
RAM: 64 MB
SoC: AR7242
Switch: bcm53128
USB: 1x USB 2.0
Ethernet: 8x GbE, 1x FE
The Ubiquiti ToughSwitch 8XP is a 8-port PoE Gigabit switch with a single
Fast-Ethernet management port. It supports both 24V passive PoE and 48V
802.11af/at PoE out on all eight ports.
By default the single Fast-Ethernet port labeled "MGMT" is configured as the
WAN port. Thus access to the device is only possible via the eight switch
ports.
Installation of the firware is possible either via serial + tftpboot or
the factory firmware update function via webinterface.
Serial: 3v3 115200 8n1
The serial header is located in the lower left corner of the switches PCB:
|
|
|
| o
| o RX
| o TX
| o GND
|
|
++ +-++-+ ++ ++ +
+--+ ++ +--++--++--+
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
[fix whitespace issue]
Signed-off-by: David Bauer <mail@david-bauer.net>
SW devices are Ubiquit ToughSwitch and EdgeSwitch series devices.
Hardware-wise they are very similar to the XM device series.
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
This commit fixes a bug in the main swconfig patch where a function
needed by the b53 driver is not exported.
Additionally it adds OF support to the b53_mdio driver for devicetree-
based probing
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
u-boot splits nand factory firmware at 2M offset, flash the first
part as kernel into spi nor and the other part as ubi into nand
flash. With previous commit increasing kernel size to 4M, generated
factory firmware is broken because ubi is at 4M offset.
This commit reduces kernel size definition to 2M in image Makefile,
producing proper factory image. Partition size in dts is kept
unchanged so that sysupgrade to a firmware with 2M+ kernel still
works.
Fixes: b496a2294c ("ath79: GL-AR750S: provide NAND support; increase kernel to 4 MB")
Reported-by: Jeff Kletsky <git-commits@allycomm.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
TP-Link Archer C20 v5 is a router with 5-port FE switch and
non-detachable antennas. It's based on MediaTek MT7628N+MT7610EN.
Specification:
- MediaTek MT7628N/N (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 5x 10/100 Mbps Ethernet
- 3x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- 7x LED (GPIO-controlled*), 2x button, power input switch
* WAN LED in this devices is a dual-color, dual-leads type which isn't
(fully) supported by gpio-leds driver. This type of LED requires both
GPIOs state change at the same time to select color or turn it off.
For now, we support/use only the green part of the LED.
Create Factory image
--------------------
As all installation methods require a U-Boot to be integrated into the
Image (and we do not ship one with the image) we are not able to create
an image in the OpenWRT build-process.
Download a TP-Link image from their Website and a OpenWRT sysupgrade
image for the device and build yourself a factory image like following:
TP-Link image: tpl.bin
OpenWRT sysupgrade image: owrt.bin
> dd if=tpl.bin of=boot.bin bs=131584 count=1
> cat owrt.bin >> boot.bin
Installing via Web-UI
---------------------
Upload the boot.bin via TP-Links firmware upgrade tool in the
web-interface.
Installing via Recovery
-----------------------
Activate Web-Recovery by beginning the upgrade Process with a
Firmware-Image from TP-Link. After starting the Firmware Upgrade,
wait ~3 seconds (When update status is switching to 0%), then
disconnect the power supply from the device. Upgrade flag (which
activates Web-Recovery) is written before the OS-image is touched and
removed after write is succesfull, so this procedure should be safe.
Plug the power back in. It will come up in Recovery-Mode on 192.168.0.1.
When active, all LEDs but the WPS LED are off.
Remeber to assign yourself a static IP-address as DHCP is not active in
this mode.
The boot.bin can now be uploaded and flashed using the web-recovery.
Installing via TFTP
-------------------
Prepare an image like following (Filenames from factory image steps
apply here)
> dd if=/dev/zero of=tp_recovery.bin bs=196608 count=1
> dd if=tpl.bin of=tmp.bin bs=131584 count=1
> dd if=tmp.bin of=boot.bin bs=512 skip=1
> cat boot.bin >> tp_recovery.bin
> cat owrt.bin >> tp_recovery.bin
Place tp_recovery.bin in root directory of TFTP server and listen on
192.168.0.66/24.
Connect router LAN ports with your computer and power up the router
while pressing the reset button. The router will download the image via
tftp and after ~1 Minute reboot into OpenWRT.
U-Boot CLI
----------
U-Boot CLI can be activated by holding down '4' on bootup.
Dual U-Boot
-----------
This is TP-Link MediaTek device with a split-uboot feature design like
a TP-Link Archer C50 v4. The first (factory-uboot) provides recovery via
TFTP and HTTP, jumping straight into the second (firmware-uboot) if no
recovery needs to be performed. The firmware-uboot unpacks and executed
the kernel.
Web-Recovery
------------
TP-Link integrated a new Web-Recovery like the one on the Archer C7v4 /
TL-WR1043v5 / Archer C50v4. Stock-firmware sets a flag in the "romfile"
partition before beginning to write and removes it afterwards. If the
router boots with this flag set, bootloader will automatically start
Web-recovery and listens on 192.168.0.1. This way, the vendor-firmware
or an OpenWRT factory image can be written.
By doing the same while performing sysupgrade, we can take advantage of
the Web-recovery in OpenWRT.
It is important to note that Web-Recovery is only based on this flag. It
can't detect e.g. a crashing kernel or other means. Once activated it
won't boot the OS before a recovery action (either via TFTP or HTTP) is
performed. This recovery-mode is indicated by an illuminated WPS-LED on
boot.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
[adjust some node names for LEDs in DTS]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
- add "gpio" group for wan_orange led
- use tpt triggers for wifi led indication
- add wifi 5 GHz led support
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
[slight commit message adjustment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Image builds for the ramips-mt7621 target currently fail with:
> WARNING: Image file ./hiwifi_hc5962-kernel.bin is too big
Disable this board for now. It can still be built using the SDK.
Signed-off-by: David Bauer <mail@david-bauer.net>
This target is still on kernel 4.9, and it looks like there is no
active maintainer for this target anymore.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This target seems to have been unmaintained for quite a while, and not a
single tester for the (now outdated) kernel 4.14 patches has been found.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This target seems to have been unmaintained for quite a while, and not a
single tester for the (now outdated) kernel 4.14 patches has been found.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds support for kernel 4.14 to the target and directly make it the
default kernel version to use.
This patch is build-tested only, but has never been device-tested. It is
only added to preserve the changes in Git history prior to removing this
target. Use it with care.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
[rebased and extended commit message, refreshed patches for 4.14.162]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The configuration of the generic subtarget was used as the default
configuration and then the subtarget configurations were adapted.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds support for kernel 4.14 to the target and directly make it the
default kernel version to use.
This patch is build-tested only, but has never been device-tested. It is
only added to preserve the changes in Git history prior to removing this
target. Use it with care.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
[rebased and extended commit message, refreshed patches for 4.14.162]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The configuration of the generic subtarget was used as the default
configuration and then the subtarget configurations were adapted.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The device label shows the address currently assigned to the OpenWrt
LAN interface.
Current setup is:
LAN *:b8 factory 0xe006 label
WAN *:b7 factory 0xe000
For vendor FW bootlog we get (manually removed parts of the address):
[ 7.520000] set LAN/WAN LWLLL
[ 7.530000] GMAC1_MAC_ADRH -- : 0x00004031
[ 7.530000] GMAC1_MAC_ADRL -- : 0x3c****b7
[ 7.530000] GDMA2_MAC_ADRH -- : 0x00004031
[ 7.540000] GDMA2_MAC_ADRL -- : 0x3c****b8
[ 7.540000] eth1: ===> VirtualIF_open
Without further information, this does not allow verification of
the currently unexpected LAN/WAN assignment (we would expect 0xe000
to be LAN).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This move the slightly different target-specific implementations of
mktplinkfw from the targets to include/image-commands.mk and renames
it to tplink-v1-image. Having a common version will increase
consistency between implementation and will complete the
tplink build command already present in the new location.
Due to the slight differences of the original implementations, this
also does some adjustments to the device build commands/variables.
This also moves rootfs_align as this is required as dependency.
Tested on:
- TL-WDR4300 v1 (ath79, factory)
- TL-WDR4900 v1 (mpc85xx, sysupgrade)
- RE210 v1 (ramips, see Tested-by)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Christoph Krapp <achterin@googlemail.com>
Refactor l2 freq scaling patch to support voltage
scaling and add support to base cache scaling on
cpu freq scaling. Update the dtsi files with the new
definition used in the new code.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
It's wrong set the mux to bias-disable. The best way to
do this is by creating a separate group and disable the
specific pins.
By documentation, any subgroup with no bias definition
is ignored so the mux definition is useless.
Rework the definition by sremoving the mux subgroup and
set the remaining subgroup with the mux function and
drive-strength
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
The opp_notifier introduced with patch 0054-Handle-OPP-voltage adjust
for some reason missed the actual registration in the opp struct,
resulting in never being registred.
This was present in kernel 4.9 patchset but dropped in the transition
to 4.14. Reintroduce this and fix patch 0055 about L2 cache scaling.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
ipTIME A8004T is a 2.4/5GHz band AC2600 router, based on Mediatek
MT7621A.
Specifications:
- SoC: MT7621A
- RAM: DDR3 256M
- Flash: SPI NOR 16MB
- WiFi:
- 2.4GHz: MT7615E
- 5GHz: MT7615E
- Ethernet: 5x 10/100/1000Mbps
- Switch: SoC internal
- USB: 1 * USB3.0 port
- UART:
- J4: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1
- Other info:
- J9: Unknown unpopulated header.
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Signed-off-by: Yong-hyu Ban <perillamint@quendi.moe>
[do not enable xhci node in DTS which is already enabled in DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The MAC address on the label of this device corresponds to the
2.4 GHz and ethernet MAC address.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Currently this device fails to boot with the OpenWrt snapshot images
(release images are unaffected). The error message is:
"LZMA ERROR 1 - must RESET board to recover".
This happens because the kernel image is too big for the bootloader
to boot. This commit works around this by decreasing the lzma dictionary
size option from the default 23 to 10.
Before this change the current OpenWrt snapshot image (uncompressed
kernel size 4875139 bytes) failed to boot, while now an even bigger
image (kernel 4.19 with snapshot default config; uncompressed kernel
size 5162833 bytes) boots just fine.
The highest lzma dictionary size option this image booted with was 11.
10 was chosen to have a bit more room for growth.
An unavoidable side-effect of this change is that the compressed kernel
image will take up more space.
Total image size with different dictionary size options:
D23 - 3973903 bytes (base)
D16 - 4113167 bytes (+3.5% - +139264 bytes)
D12 - 4317967 bytes (+8.7% - +344064 bytes)
D11 - 4383503 bytes (+10.3% - +409600 bytes)
D10 - 4461327 bytes (+12.3% - +487424 bytes)
Fixes: FS#1484
Signed-off-by: Mason Clarke <mclarke2355@gmail.com>
Both devices are available in 64M and 128M RAM configurations but there
is no visial indication which configuration one might get.
So just to be sure we properly support both configurations switch to
kmod-atk10k-ct-smallbuffers.
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
Currently the patch only changes break to use goto statement instead.
But not necessary acutually since the ret value checked after the for loop.
So it is okay for the break case before changed by the patch also.
This patch only reverts the following commit partially.
https://github.com/openwrt/openwrt/commit/ddc11c3932c7b7b7df7d5fbd48f207e7
Note: The changes are mainly applied into the linux kernel upstream.
Signed-off-by: Tokunori Ikegami <ikegami.t@gmail.com>
Cc: Koen Vandeputte <koen.vandeputte@ncentric.com>
Currently the patch only changes break to use goto statement instead.
But not necessary acutually since the ret value checked after the for loop.
So it is okay for the break case before changed by the patch also.
This patch only reverts the following commit partially.
ddc11c3932
Note: The changes are mainly applied into the linux kernel upstream.
Signed-off-by: Tokunori Ikegami <ikegami.t@gmail.com>
Cc: Koen Vandeputte <koen.vandeputte@ncentric.com>
Images generated for the TP-Link RE200v1 cannot be updated using
sysupgrade, because a necessary call to append-metadata was missing.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Edimax RA21S is a dual band 11ac router,
based on MediaTek MT7621A and MT7615N chips.
Specification:
- SoC: MediaTek MT7621A dual-core @ 880MHz
- RAM: 256M (Nanya NT5CC128M16IP)
- FLASH: 16MB (Macronix MX25L12835F)
- WiFi: 2.4/5 GHz 4T4R
- 2.4GHz MediaTek MT7615N bgn
- 5GHz MediaTek MT7615N nac
- Switch: SoC integrated Gigabit Switch (4 x LAN, 1 x WAN)
- USB: No
- BTN: Reset, WPS
- LED: 4 red LEDs, indistinguishable when case closed
- UART: through-hole on PCB.
J1: 3.3V - RX - GND - TX / 57600-8N1. 3.3V is the square pad
Installation:
Update the factory image via the OEM web-interface
(by default: http://192.168.2.1/)
User: admin
Password: 1234
The sysupgrade image can be installed via TFTP
from the U-Boot bootloader. Connect via ethernet port 2.
Tested on device by @UAb5eSMn
Signed-off-by: Maksym Medvedev <redrathnure@gmail.com>
[split DTS and take over improvements from RG21S, extend commit
message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
330-MIPS-kexec-Accept-command-line-parameters-from-users.patch causes
problems when building with -Werror=unused-result.
arch/mips/kernel/machine_kexec.c: In function 'machine_kexec_init_argv':
arch/mips/kernel/machine_kexec.c:76:2: error: ignoring return value of 'copy_from_user', declared with attribute warn_unused_result [-Werror=unused-result]
copy_from_user(kexec_argv_buf, buf, size);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Fix this by handling the return value in an appropriate way.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
CONFIG_PINCTRL_SUN4I_A10 controls both the A10 and the A20 enablong of
the pinctrl driver, this is necessary since upstream commit
5d8d349618a9464714c07414c5888bfd9416638f ("pinctrl: sunxi: add A20
support to A10 driver") which has been included in v4.13 and onwards.
Fixes: ad2b3bf310 ("sunxi: Add support for kernel 4.14")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Shared base-files package contains functions for LED migration that
are already used by several targets. Apply those also to lantiq and
drop the (redundant) local code.
While at it, reorder board names in file.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The only device in samsung target is meant to be built with s5pv210
subtarget. Thus, though this won't make a difference for a
one-subtarget target, already add the condition to the Makefile to
make the assignment obvious.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch changes the samsung target to calculate the DTS file name
from vendor and device name and the SOC (i.e. subtarget) following
the common scheme:
soc_vendor_model.dts
This also updates the device definition name to make compatible,
image name, menuconfig name and DTS name consistent.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The TP-Link Archer C20i previously had a generic Ralink MAC address set
for both radios, as the caldata does only contain a generic MAC address.
Set the MAC address from the vendor firmware for both radios to assign
unique MAC addresses to every device.
Signed-off-by: David Bauer <mail@david-bauer.net>
The TP-Link Archer C2 v1 previously had a generic Ralink MAC address set
for the 5GHz radio (MT7610), as the caldata does only contain a generic
MAC address.
Set the MAC address from the vendor firmware for the 5GHz radio to
assign unique MAC addresses to every device.
Signed-off-by: David Bauer <mail@david-bauer.net>
Use the WPS LED to indicate system status like it is done for the
TP-Link Archer C2 v1 and many other boards.
Signed-off-by: David Bauer <mail@david-bauer.net>
This converts all MediaTek MT7620 boards from TP-Link to use the now
supported WiFi throughput LED trigger. This way, the LED state now
covers all VAPs regardless of their name.
Also align all single-WiFi LEDs to represent the state of the 2.4GHz
radio. This was not always the case previously, as later-added support
for the MT7610 altered the phy probing order.
Signed-off-by: David Bauer <mail@david-bauer.net>
HC5661 does not have 5GHz WiFi or LED.
Fixes: e6e373d348 ("ramips: Add DTS files for HiWiFi HC5x61 models")
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
TP-Link RE200 v1 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7620A+MT7610EN.
Specifications
--------------
- MediaTek MT7620A (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet
- UART header on PCB (57600 8n1)
- 8x LED (GPIO-controlled; only 6 supported), 2x button
There are 2.4G and 5G LEDs in red and green which are controlled
separately. The 5G LED is currently not supported, since the GPIOs couldn't
be determined.
Installation
------------
Web Interface
-------------
It is possible to upgrade to OpenWrt via the web interface. However, the
OEM firmware upgrade file is required and a tool to fix the MD5 sum of
the header. This procedure overwrites U-Boot and there is not failsafe /
recovery mode present! To prepare an image, you need to take the header
and U-Boot (i.e. 0x200 + 0x20000 bytes) from an OEM firmware file and
attach the factory image to it. Then fix the header MD5Sum1.
Serial console
--------------
Opening the case is quite hard, since it is welded together. Rename the
OpenWrt factory image to "test.bin", then plug in the device and quickly
press "2" to enter flash mode (no line feed). Follow the prompts until
OpenWrt is installed.
Unfortunately, this devices does not offer a recovery mode or a tftp
installation method. If the web interface upgrade fails, you have to open
your device and attach serial console. Since the web upgrade overwrites
the boot loader, you might also brick your device.
Additional notes
----------------
MAC address assignment is based on stock-firmware. For me, the device
assigns the MAC on the label to Ethernet and the 2.4G WiFi, while the 5G
WiFi has a separate MAC with +2.
*:88 Ethernet/2.4G label, uboot 0x1fc00, userconfig 0x0158
*:89 unused userconfig 0x0160
*:8A 5G not present in flash
This seems to be the first ramips device with a TP-Link v1 header. The
original firmware has the string "EU" embedded, there might be some region-
checking going on during the firmware upgrade process. The original
firmware also contains U-Boot and thus overwrites the boot loader during
upgrade.
In order to flash back to stock, the first header and U-Boot need to be
stripped from the original firmware.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
MiWiFi Nano has two LAN ports, which are in reverse order. Add port numbers
to them, and disable unused ports.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Handle both variants separately. This removes the need for calling
swconfig to detect the switch, and simplifies future changes.
Signed-off-by: Josua Mayer <josua.mayer@jm0.eu>
This adds a "factory" image for the aircube-isp devices. Note that the
firmware can't be uploaded without prior special preparation. For the
most recent instructions on how to do that, visit the OpenWRT wiki page
of the Ubiquiti airCube ISP for details:
https://openwrt.org/toh/ubiquiti/ubiquiti_aircube_isp
Current procedure:
With the original firmware 2.5.0 it is possible to upload and execute a
script via the configuration. To do that download and unpack the
original configuration, adapt uhttpd config to execute another lua
handler (placed in the config directory) and pack and upload it again.
The lua handler can call a script that mounts an overlayfs and modifies
the "fwupdate.real" binary so that an unsigned image is accepted. The
overlayfs is necessary because a security system (called tomoyo) doesn't
allow binaries in other locations than /sbin/fwupdate.real (and maybe
some more) to access the flash when executed via network.
A big thanks to Torvald Menningen (Snap) from the OpenWRT forum for
finding out how to patch the binary so that it accepts an unsigned
image.
The current step-by-step procedure is:
- Use a version 2.5.0 of the original firmware. This is important
because a binary file will be modified.
- Download a configuration.
- Unpack it (it's just a tar gz file without an ending).
- Add the following to uhttpd:
``````
config 'uhttpd' 'other'
list listen_http 0.0.0.0:8080
list listen_http [::]:8080
option 'home' '/tmp/persistent/config/patch/www'
option lua_prefix '/lua'
option lua_handler '/tmp/persistent/config/patch/handler.lua'
``````
- Create a `patch` subfolder.
- Create a `patch/www` subfolder.
- Create a `patch/handler.lua` with the following content:
``````
function handle_request(env)
uhttpd.send("Status: 200 OK\r\n")
uhttpd.send("Content-Type: text/plain\r\n\r\n")
local command = "/bin/sh /tmp/persistent/config/patch/patch.sh 2>&1"
local proc = assert(io.popen(command))
for line in proc:lines() do
uhttpd.send(line.."\r\n")
end
proc:close()
end
``````
- Create a `patch/patch.sh` with the following content:
``````
#!/bin/sh -x
set -e
set -u
set -x
UBNTBOX_PATCHED="/tmp/fwupdate.real"
MD5FILE="/tmp/patchmd5"
cat <<EOF > ${MD5FILE}
c33235322da5baca5a7b237c09bc8df1 /sbin/fwupdate.real
EOF
# check md5 of files that will be patched
if ! md5sum -c ${MD5FILE}
then
echo "******** Error when checking files. Refuse to do anything. ********"
exit 0
fi
# prepare some overlay functionality
LOWERDIR="/tmp/lower_root"
mkdir -p ${LOWERDIR}
mount -t squashfs -oro /dev/mtdblock3 ${LOWERDIR}
overlay_some_path()
{
PATH_TO_OVERLAY=$1
ALIAS=$2
UPPERDIR="/tmp/over_${ALIAS}"
WORKDIR="/tmp/over_${ALIAS}_work"
mkdir -p ${UPPERDIR}
mkdir -p ${WORKDIR}
mount -t overlay -o lowerdir=${LOWERDIR}${PATH_TO_OVERLAY},upperdir=${UPPERDIR},workdir=${WORKDIR} overlay ${PATH_TO_OVERLAY}
}
# patch the ubntbox binary.
overlay_some_path "/sbin" "sbin"
echo -en '\x10' | dd of=/sbin/fwupdate.real conv=notrunc bs=1 count=1 seek=24598
echo "******** Done ********"
``````
- Repack the configuration.
- Upload it via the normal web interface.
- Wait about a minute. The webserver should restart.
- Now there is a second web server at port 8080 which can call the lua
script. Visit the page with a web browser. Link is for example
http://192.168.1.1:8080/lua
- You should see the output of the script with a "*** Done ***" at the
end. Note that the patches are not permanent. If you restart the
router you have to re-visit the link (but not re-upload the config).
- Now you can upload an unsigned binary via the normal web interface.
Signed-off-by: Christian Mauderer <oss@c-mauderer.de>
Convert leading spaces to tabs and generally harmonize leading
whitespace indent in the file.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
No bash features are actually used here.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[slightly adjust commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This has nothing that needs bash.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[add prefix to commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This has nothing that needs bash.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[add prefix to commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
There is nothing that needs bash anymore.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[add prefix to commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This replaces deprecated backticks by more versatile $(...) syntax.
Found with shellcheck.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[alter commit title, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Enables proper checking. Matches printf behavior in C.
Found with shellcheck.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[add prefix to commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
let is a bashism.
Found with shellcheck.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[add prefix to commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds an LED trigger for the WAN LED on top of the TP-Link
TL-WR902AC v3. Currently, only the LED on the port itself shows the link
state, while the LED on top of the device stays dark.
The WAN port of the device is a hybrid LAN/WAN one, hence why the LED at
the port was labled LAN.
Signed-off-by: David Bauer <mail@david-bauer.net>
This patch uses the SOC variable to calculate DTS names automatically
based on the SOC and the device definition node name.
This reduces redundancy and (by having to choose DTS name
appropriately) will unify the naming of a device in different places
(image/Makefile, DTS name, compatible, image name). This is supposed
to make life easier for developers and reviewers.
Since the kernel uses a "soc-device.dts" scheme for this target, we
use this for the derivation of DEVICE_DTS, too, leaving the DTS names
unchanged for this target.
Note that for some devices the kernel itself uses inconsistent names
(DTS naming scheme vs. compatible), leaving us with a manual overwrite
of DEVICE_DTS for those cases.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch uses the SOC variable to calculate DTS names automatically
based on the SOC and the device definition node name.
This reduces redundancy and (by having to choose DTS name
appropriately) will unify the naming of a device in different places
(image/Makefile, DTS name, compatible, image name). This is supposed
to make life easier for developers and reviewers.
Since the kernel uses a "soc-device.dts" scheme for this target, we
use this for the derivation of DEVICE_DTS, too, and rename the files
not having followed it so far.
Note that for some devices the kernel itself is inconsistent, leaving
us with a manual overwrite for ap.dk01.1-c1 and ap.dk04.1-c1.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Several devices in mt76x8 subtarget use the following line to set
up wmac in their DTS(I) files:
ralink,mtd-eeprom = <&factory 0x4>
This is strange for several reasons:
- They should use mediatek,mtd-eeprom on this SOC
- The caldata is supposed to start at 0x0
- The parent DTSI mt7628an.dtsi specifies mediatek,mtd-eeprom anyway,
starting from 0x0
- The offset coincides with the default location of the MAC address
in caldata
Based on the comment in b28e94d4bf ("ramips: MiWiFi Nano fixes"),
it looks like the author for this device wanted to actually use
mtd-mac-address instead of ralink,mtd-eeprom. A check on the same
device revealed that actually the MAC address start at offset 4 there,
so the correct caldata offset is 0x0.
Based on these findings, and the fact that the expected location on
this SOC is 0x0, we remove the "ralink,mtd-eeprom = <&factory 0x4>"
statement from all devices in ramips (being only mt7628an anyway).
Thanks to Sungbo Eo for finding and researching this.
Reported-by: Sungbo Eo <mans0n@gorani.run>
Fixes: b28e94d4bf ("ramips: MiWiFi Nano fixes")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Physically allocated memory for modules needs to be registered with kmemleak,
so it can track it as object.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
We have only 11 sensors on ipq806x. Fix the reg property
to load the right amount of data instead of the entire
space.
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [nbg6817/ipq8065]
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Tsense driver for ipq806x have various problem.
- Emit wrong error. On probing of this driver, nvmem driver can be
not ready and this cause a EDEFER error. Actually this is not an
error as the kernel will retry to probe the driver after the
nvmem driver is loaded.
- Use uninitialized value on trigger of critical temp
- Doesn't free allocated memory
Because of this, rework the driver and improve it by removing extra
load of data.
Change the logic of loading data. Use the backup calib data only
when the calib data is not present. As the calibration is only
needed to set the temp offset, we don't really need to read
both calib data and set the offset based only on the backup one.
Also change how the notifier function work. At times when we
output the trigger message, we already have read the temp so
remove the extra read and the wrong uninitialized data that
probably caused a kernel panic for null pointer exception.
(Think we never experience this bug because the router
never reached that temp ever... So just lucky)
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [nbg6817/ipq8065]
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
The config name for cpufreq driver has changed.
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [nbg6817/ipq8065]
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
The new driver use opp table to register frequency.
Drop psv bindings as they are not used anymore.
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [nbg6817/ipq8065]
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
The new driver use opp table to register frequency.
Drop psv bindings as they are not used anymore.
Adds speedbin definition for nvmem driver
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [nbg6817/ipq8065]
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
This patch has been proposed but never actually merged to
mainline. It was accepted but never re proposed by the
creator.
Rework it, fix kernel panic cause by double kfree.
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [nbg6817/ipq8065]
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Backport patch applied to qcom-cpufreq-kryo
driver as krait cpu will base on this driver.
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [nbg6817/ipq8065]
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Drop old cpufreq as now we have new driver that
can use normal kernel opp definition
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [nbg6817/ipq8065]
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Rework 0052-PM-OPP-Update-the-voltage-tolerance-when-adjusting-t
to reflect changes upstream.
- Skip unnecessary allocation of buffer to set u_volt
- Change opp u_volt directly
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [nbg6817/ipq8065]
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Update 0049-PM-OPP-Support-adjusting-OPP-voltages-at-runtime with
upstream version.
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [nbg6817/ipq8065]
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
It has been notice a buf in L2 cache scaling where the scaling is not
done proprely if the frequency is set to the initial state before
the new frequency.
From: https://patchwork.kernel.org/patch/10565443/
* The clocks are set to aux clock rate first to make sure the
* secondary mux is not sourcing off of QSB. The rate is then set to
* two different rates to force a HFPLL reinit under all
* circumstances.
In the initial stage of boot to force a new frequency to apply, is
needed to first set the frequency back to the lowest one (aux_rate)
and then to the target one. This force and make sure the controller
actually switch the frequency to the right one. Apply the same
mechanism to L2 frequency scaling. Before scaling to the target
frequency, first set the frequency to the aux_rate to force the
transition, then scale it to the target frequency. Doing the wrong way
can produce unexpected results and could lock the scaling mechanism
until a full reboot is done (Causing a full reset by the krait-cc driver)
From: https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/commit/?id=77612720a2362230af726baa4149c40ec7a7fb05
When the Hfplls are reprogrammed during the rate change,
the primary muxes which are sourced from the same hfpll
for higher frequencies, needs to be switched to the 'safe
secondary mux' as the parent for that small window. This
is done by registering a clk notifier for the muxes and
switching to the safe parent in the PRE_RATE_CHANGE notifier
and back to the original parent in the POST_RATE_CHANGE notifier.
This should apply also to L2 scaling... as we can't relly use
the notifier, we manually do this on L2 scaling.
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [nbg6817/ipq8065]
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Deactivate CONFIG_SFP for kernel 4.19 in the generic configuration.
The CONFIG_SFP configuration option was not set to anything in the
ath79 build for me, set it to deactivated by default.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The factory image for the dlink_dir-615-e4 is getting too big which makes
the full ath79 tiny build fail, deactivate it by default.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The device label contains:
E01: 74:4D:28:xx:xx:30
E05: 74:4D:28:xx:xx:34
The first value corresponds to the address set in hard_config 0x10.
That one is taken for the label MAC address.
Signed-off-by: Sven Roederer <freifunk@it-solutions.geroedel.de>
The node pinctrl0 is already set up in the SOC DTSI files, but
defined again as member of pinctrl in most of the device DTS(I)
files. This patch removes this redundancy for the entire ramips
target.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
VMWare ESXI 6.5 and above is not compatible with
subformat=monolithicSparse (The default qemu-img convert -O VMDK option).
Monolithic Sparse vmdk can be imported, but issues occur when running
sysupgrade with new images and other tasks that modify the file system
(issues like Kernel panics, reboot loops, sometimes crashing the Host ESXI
box).
This change creates an additional VMDK output file for ESXI that sets the
subformat to monlithicFlat, and the adapter_type to the SCSI lsilogic
controller.
This change existed back on:
25e36d379e
But it looks like the change was removed when refactoring occurred with:
5f6a2732f892b6229473576d89cc963ae9c97d5d
Signed-off-by: John Sommerville <jsommerville@untangle.com>
led2l and led2h value is incorrectly set by led3l and led3h.
Bug was introduced in commit: 863e79f8d5
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Fixes: 863e79f8d5 ("lantiq: add support for kernel 4.9")
MAC addresses are stored in factory partition at:
0x0004: WiFi 2.4GHz (label_mac +1)
0x0028: LAN, WAN (label_mac)
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This patch does the following:
- prepend vendor name to model
- set status LEDs to follow the behavior in stock FW
- simplify state_default node definition
- use generic name for flash node
Stock FW status indicators:
https://files.xiaomi-mi.com/files/Mi_Router_Wi-Fi_Nano/Mi_router-NANO_EN.pdf
> Yellow: power on / off
> Blue: during normal operation
> Red: in case of problems with the operation of the device
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This moves the include of lantiq.dtsi from the DTS files to the
parent falcon_lantiq_easy98000.dtsi.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This renames lantiq DTS(I) files to follow soc_vendor_device scheme.
This will make DTS files easier to maintain.
As a side effect, DTS file name can be derived from device node
names now, only having to specify a SOC variable in Makefiles.
While at it, move files to arch/mips/boot/dts/lantiq subfolder.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Assign the ASC pins to the serial controller node instead of using pin
hogging (where pins are assigned to the pin controller).
This is the preferred way of assigning pins upstream.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Assign the PCI pins to the PCI controller node instead of using pin
hogging (where pins are assigned to the pin controller).
This is the preferred way of assigning pins upstream.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Assign the STP pins to the STP GPIO controller node instead of using
pin hogging (where pins are assigned to the pin controller).
This is the preferred way of assigning pins upstream.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Assign the GPHY LED pins to the Ethernet controller node instead of
using pin hogging (where pins are assigned to the pin controller).
This is the preferred way of assigning pins upstream.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Assign the NAND pins to the NAND controller node instead of using pin
hogging (where pins are assigned to the pin controller).
This is the preferred way of assigning pins upstream.
While here, define all NAND pins (CLE, ALE, read/RD, ready busy/RDY and
CE/CS1). This means that the pinctrl subsystem knows that these pins are
in use and cannot be re-assigned as GPIOs for example.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Define the SPI pins in the corresponding SoCs.dtsi and assign them to
the SPI controller node. All known boards use CS4 and it's likely that
this is hardcoded in bootrom so this doesn't bother with having
per-board SPI pinmux settings.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Assign the MDIO pins to the switch node instead of using pin hogging
(where pins are assigned to the pin controller).
This is the preferred way of assigning pins upstream.
This converts amazonse, ar9 and vr9. danube is skipped because the pin
controller doesn't define a pinmux for the MDIO pins (some of the SoC
pads may be hardwired to the MDIO pins instead of being configurable).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
This fixes the state_default node by setting the correct groups and
inheriting &state_default from parent DTSI directly.
The compatible for the wifi nodes is changed to the more generic
mediatek,mt76.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
So far, lan/wan MAC address for Edimax RG21S are only read using
mtd_get_mac_ascii, so eth0.1 and eth0.2 addresses are set, but
eth0 address is random. Since the device's LAN address is the same
as for 2.4 GHz, though, this patch set's the eth0 address based
on the 2.4 GHz one, which can be extracted by mtd-mac-address.
This will also allow to move the label MAC address setup to DT.
The setup of lan_mac and wan_mac are kept in 02_network, so those
locations are still in use, too.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch does the following:
- move WiFi LED setup to DTS
- fix LAN/WAN MAC addresses and add label MAC address
- wan5G -> wlan5G, power -> led_power
- increase flash SPI frequency to 30MHz
MAC addresses are stored in Factory partition at:
0x1006: WiFi 2.4GHz, WAN (label_mac)
0x5006: WiFi 5GHz, LAN (label_mac +4)
By improving flash speed,
`time dd if=/dev/mtdblock8 of=/dev/null bs=2k`
is reduced from 7m 10.26s to 5m 9.52s.
Using higher frequencies did not improve speed further.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
The current ethernet MAC address setup of TL-WDR4300 board is different
from the setup of stock firmware:
OpenWrt: lan = label_mac -2, wan = label_mac -2
stock: lan = label_mac, wan = label_mac +1
This patch applies to all devices using TL-WDR4300 board:
TL-WDR3600 v1
TL-WDR4300 v1
TL-WDR4300 v1 (IL)
TL-WDR4310 v1
Mercury MW4530R v1
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
The current ethernet MAC address setup of TL-WDR4300 board is different
from the setup of stock firmware:
OpenWrt: lan = label_mac -2, wan = label_mac -2
stock: lan = label_mac, wan = label_mac +1
The full address assignment is as follows:
LAN label
WAN label + 1
5G label
2G label - 1
This patch changes all devices using TL-WDR4300 board:
TL-WDR3600 v1 (checked on device)
TL-WDR4300 v1 (checked on device)
TL-WDR4300 v1 (IL)
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[rephrase/extend commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Hardware
--------
SoC: Qualcomm IPQ4029
RAM: 512M DDR3
FLASH: - 128MB NAND (Macronix MX30LF1G18AC)
- 4MB SPI-NOR (Macronix MX25R3235F)
TPM: Atmel AT97SC3203
BLE: Texas Instruments CC2540T
attached to ttyMSM0
ETH: Atheros AR8035
LED: WiFi (amber / green)
System (red / green)
BTN: Reset
To connect to the serial console, you can solder to the labled pads next
to the USB port or use your Aruba supplied UARt adapter.
Do NOT plug a standard USB cable into the Console labled USB-port!
Aruba/HPE simply put UART on the micro-USB pins. You can solder yourself
an adapter cable:
VCC - NC
D+ - TX
D- - RX
GND - GND
The console setting in bootloader and OS is 9600 8N1. Voltage level is
3.3V.
To enable a full list of commands in the U-Boot "help" command, execute
the literal "diag" command.
Installation
------------
1. Get the OpenWrt initramfs image. Rename it to ipq40xx.ari and put it
into the TFTP server root directory. Configure the TFTP server to
be reachable at 192.168.1.75/24. Connect the machine running the TFTP
server to the ethernet port of the access point.
2. Connect to the serial console. Interrupt autobooting by pressing
Enter when prompted.
3. Configure the bootargs and bootcmd for OpenWrt.
$ setenv bootargs_openwrt "setenv bootargs console=ttyMSM1,9600n8"
$ setenv nandboot_openwrt "run bootargs_openwrt; ubi part aos1;
ubi read 0x85000000 kernel; bootm 0x85000000"
$ setenv ramboot_openwrt "run bootargs_openwrt;
setenv ipaddr 192.168.1.105; setenv serverip 192.168.1.75;
netget; set fdt_high 0x87000000; bootm"
$ setenv bootcmd "run nandboot_openwrt"
$ saveenv
4. Load OpenWrt into RAM:
$ run ramboot_openwrt
5. After OpenWrt booted, transfer the OpenWrt sysupgrade image to the
/tmp folder on the device.
6. Flash OpenWrt:
$ ubidetach -p /dev/mtd1
$ ubiformat /dev/mtd1
$ sysupgrade -n /tmp/openwrt-sysupgrade.bin
To go back to the stock firmware, simply reset the bootcmd in the
bootloader to the original value:
$ setenv bootcmd "boot"
$ saveenv
Signed-off-by: David Bauer <mail@david-bauer.net>
Device support for Belkin F9K1109v1 was added using set_usb_led()
although this was removed in 772b27c207 ("ramips: set F5D8235 v1
usb led trigger via devicetree").
Use ucidef_set_led_usbport() instead.
Fixes: f2c83532f9 ("ramips: add support for Belkin F9K1109v1")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[rephrase commit title and message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This harmonizes the line wrapping in image Makefile device
definitions, as those are frequently copy-pasted and are a common
subject of review comments. Having the treatment unifying should
reduce the cases where adjustment is necessary afterwards.
Harmonization is achieved by consistently (read "strictly")
applying certain rules:
- Never put more than 80 characters into one line
- Fill lines up (do not break after 40 chars because of ...)
- Use one tab for indent after wrapping by "\"
- Only break after pipe "|" for IMAGE variables
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This harmonizes the line wrapping in image Makefile device
definitions, as those are frequently copy-pasted and are a common
subject of review comments. Having the treatment unifying should
reduce the cases where adjustment is necessary afterwards.
Harmonization is achieved by consistently (read "strictly")
applying certain rules:
- Never put more than 80 characters into one line
- Fill lines up (do not break after 40 chars because of ...)
- Use one tab for indent after wrapping by "\"
- Only break after pipe "|" for IMAGE variables
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This enables using 4kiB sectors as erase blocks for 4MiB NOR flash ICs
that support it.
Writeable jffs2 overlay used to store settings requires a partition with
at least 5 erase blocks, so using small sectors is essential for devices
with 4MiB flash.
Sysupgrading a device running firmware without this feature will likely
not allow to preserve configs automatically but since ath79 is
considered to be in a "technology preview" state it shouldn't be a
problem.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Specifications:
- FCC ID: KA2IR615E3
- SoC: MIPS32 24K 400 MHz Atheros AR7240
- RAM: 32 MiB DDR SDRAM ESMT M13S2561616A-5T
- Flash: 4 MiB NOR SPI Macronix MX25L3208E
- Wireless: AR9287 2.4 GHz 802.11n 2T2R, 2x RP-SMA connectors
- Ethernet: 5x 100BASE-TX Fast Ethernet
- LEDs: 9x GPIO, 1x ath9k
- Buttons: 2x tactile switches
- UART: 3.3 V, 115200 8n1
- USB: simple hardware modification required, 1x USB 1.1 Full Speed
Partitioning notes:
Vendor firmware (based on CameoAP99) defines two additional partitions:
"mac" @0x3b0000, size 0x10000 and "lp" @0x3c0000, size 0x30000.
The "mac" partition stores LAN MAC address and hardware board name.
However, the vendor firmware uses addresses from "nvram" partition, and
the board name is used only for informational purposes in the Web
interface (included in the pages' header), not affecting the firmware
image check.
The "lp" partition is supposed to contain a "language pack" (which can
be used to add an additional language support to the Web interface) and
is flashed separately, using the vendor firmware upgrade page.
Since these partitions are absolutely useless for OpenWrt and
overwriting them doesn't prevent downgrading to obsolete vendor
firmware, this patch appends the valueable space to "firmware".
Installation instructions:
- Upgrade from OpenWrt ar71xx with "sysupgrade -f -n"
or
- Upload as a firmware update via the vendor Web-interface
or
- Connect UART and use "loady" to upload and run OpenWrt initramfs
image, then sysupgrade from it (TFTP client doesn't work)
or
- Before powering up hold "reset" button and keep it pressed for about
15 seconds after, then access fail safe Web server on 192.168.0.1 (the
old uIP TCP/IP protocol stack is not compatible with modern Linux, the
kernel, so you'll need to use some other OS to do this). Can be
performed without a Web-browser too:
curl http://192.168.0.1/cgi/index \
-F Send=@openwrt-ath79-tiny-dlink_dir-615-e4-squashfs-factory.bin
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Netgear WNDR routers (AR9344 models) like WNDR4300 have 128 MiB of flash
memory but only first 32 MiB are used now - both by vendor's firmware and
OpenWrt. This patch concatenates two regions of flash memory: ubi part
of firmware partition and reserved (unused) space beyond 'caldata_backup'
while preserving ART backup. No data is wiped or moved away.
This increases area for OS ubi volumes from 23 to 119 Megabytes.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
It has been used by several people for some time already and feedback
has been mostly positive.
Ref: https://github.com/openwrt/openwrt/pull/2472
Tested-by: Hannu Nyman <hannu.nyman@iki.fi> [ipq8065, R7800]
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ipq8065, NBG6817]
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[separate commit, commit subject and description facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
- Use new dwc3-qcom usb driver.
- Drop dwc3-of-simple as we have a dedicated driver now.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[split into separate commit, commit subject facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Voltage tolerance is accounted per core, not per cpu, so add
missing DT entry.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Added patch:
- 063-3 Fix tsense shared memory problem
Recent changes in ioremap_resource function are causing fails for the
memory areas which are already mapped. This changes are causing tsense
driver failures during initialization:
qcom-tsens 900000.thermal-sensor: tsens init failed
So this patch uses simple ioremap in order to use this shared memory
space.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[commit subject and desciption facelitf]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Improve rediability of gpio mdio list. No functional change.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[proper authorship of the patch]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
From documentation
https://www.kernel.org/doc/Documentation/devicetree/bindings/chosen.txt
should be just stdout-path
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[proper authorship of the patch]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Reorganize dts to use tags from ipq8064 dtsi
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
There is warning with "property has invalid length (4 bytes)"
related to nand definition. Set size-cells to zero to fix this.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Add missing watchdog to list of compatible timers
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Add some tags for nand and sata structure to easily
reference them in other dts.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Increase drive-strength from
https://lore.kernel.org/patchwork/patch/626885/
2mA drive strength is not enough when we connect multiple i2c devices
on the bus with different pull up resistors.
This issue was detected when multiple i2c devices
connected on the other side of level shifters on Linaro sensor board.
Maxing up to 16mA made i2c much stable.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Spc is disabled in ipq8065 board as it does cause cpu lockup
(probably caused by wrong register being set)
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Use new usb3 implementation and refresh dts to the new dwc3 structure
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[proper authorship of the patch]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
- ipq8064 compatible was missing from nbg6817.
- Rename ap148 with a better descriptive name.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[proper authorship of the patch]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
DT spec require okay instead of ok in dts files
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reworked:
- 0034 patchset update
Added:
- 080 Add support for pinctrl-msm framework
Removed:
- 0074-ipq806x-usb-Control-USB-master-reset.patch
(we now have a dedicated driver for qcom usb)
- 0047-mtd-nand-Create-a-BBT-flag-to-access-bad-block-marke
(merged upstream)
- 310-msm-adhoc-bus-support
(it looks like it was never actually used in any dts)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[commit subject and description facelift, SoB fix]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
PCI_V3_SEMI config symbol was found missing in generic kernel config
after ipq806x config refresh to 4.19.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[commit subject and description facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
These changes are needed in order to migrate old kernel 4.14 config to
the upcoming kernel version 4.19. Also add missing configuration
options that comes up with this SoC.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[line wrap long commit description, add 4.19 to subject, soc->SoC]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This copies files from files-4.14 to files-4.19 directory in order to
get clear diffs for any changes done from now on.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[added missing commit description, refreshed ea8500 and wpq864 DTS]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This partially reverts commit 32144ba275.
This commit replaced gpio-exports in favor of gpio-hogs for enabling USB
power at boot, but this rids the user of control of the USB port power
present on this device for a long time. It was agreed on a mailing list
[1] that this is not the way to go, and this patch breaks a very common
use-case of WWAN modem reset by power cycle, used on a lot USB equipped
routers, hence revert this change until a better solution can be found.
[1] http://lists.infradead.org/pipermail/openwrt-devel/2019-November/020151.html
Tested-by: Sungbo Eo <mans0n@gorani.run>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[adjusted commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
