Hardware Spec
-SoC: Rockchip RK3588S
CPU: Quad-core ARM Cortex-A76(up to 2.4GHz) and quad-core Cortex-A55 CPU (up to 1.8GHz)
GPU: Mali-G610 MP4, compatible with OpenGLES 1.1, 2.0, and 3.2, OpenCL up to 2.2 and Vulkan1.2
VPU: 8K@60fps H.265 and VP9 decoder, 8K@30fps H.264 decoder, 4K@60fps AV1 decoder, 8K@30fps H.264 and H.265
NPU: 6TOPs, supports INT4/INT8/INT16/FP16
-RAM: 64-bit 4GB/8GB LPDDR4X at 2133MHz
-Flash: 32GB/None eMMC, at HS400 mode
-Ethernet: one Native Gigabit Ethernet, and one PCIe 2.5G Ethernet
-USB: one USB 3.0 Type-A and one USB 2.0 Type-A
-PCIe: one M.2 Key M connector with PCIe 2.1 x1
-HDMI:
compatible with HDMI2.1, HDMI2.0, and HDMI1.4 operation
support up to 7680x4320@60Hz
Support RGB/YUV(up to 10bit) format
-microSD: support up to SDR104 mode
-GPIO:
30-pin 2.54mm header connector
up to 1x SPI, 3x UARTs, 3x I2Cs, 2x SPDIFs, 1x I2Ss, 3x PWMs, 20x GPIOs
-Debug: UART via 3-Pin 2.54mm header, or on-board USB-C to UART
-LEDs: 4 x GPIO Controlled LED (SYS, WAN, LAN, LED1)
-others:
2 Pin 1.27/1.25mm RTC battery input connector for low power RTC IC HYM8563TS
MASK button for eMMC update
one user button
-Power supply: USB-C, support PD, 5V/9V/12V/20V input
-PCB: 8 Layer, 62x90x1.6mm
-Ambient Operating Temperature: 0℃ to 70℃
Installation:
Uncompress the OpenWrt sysupgrade and write image to the SD card using dd (dd if=*.img of=/*)
eMMC Installation:
Boot from the SD card
Uncompress the OpenWrt sysupgrade image
fash to eMMC : dd if=*.img of=/dev/mmcblk1
sync
remove SD card
reboot
Signed-off-by: Antonio Flores <antflores627@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16275
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport ir-receiver/minipcie/poweroff/spi/usb-c support and other
minor fixes for the NanoPC T6 board.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16443
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Update sysupgrade script (fortinet.sh) for Fortinet devices in
mvebu/cortexa9 and fix the following issues,
- Some individuals of FortiGate/FortiWiFi 30E/5xE devices has wrong
kernel/rootfs offsets in "firmware-info" partition and they are not
updated with the current sysupgrade script for Fortinet devices
(fortinet.sh).
As a result, the bootloader tries to load kernel data from the wrong
address and boot with it after OpenWrt installation.
The new script handles offsets in addition to length values.
and improve the following points.
- Only 2 bytes are handled with the current sysupgrade script
(fortinet.sh) for kernel/rootfs length. The new script handles 4 bytes
instead.
- The image names of image0/image1 are not handled and not updated when
sysupgrade. The new sysupgrade script handles it and update to
"<dist> <version> <revision>" if firmware metadata is available.
(ex.: "OpenWrt SNAPSHOT r27440-25384026")
log of new sysupgrade script (fortinet.sh):
Tue Sep 17 10:29:16 UTC 2024 upgrade: Performing system upgrade...
Image Index: 0
Image Name : "OpenWrt SNAPSHOT r27440-25384026"
--> "OpenWrt SNAPSHOT r27441-b3a0806a05"
kernel:
old: 0x003c4e00@0x00200000
new: 0x003c4e00@0x00200000
rootfs:
old: 0x005c0200@0x00800000
new: 0x005c0200@0x00800000
Unlocking kernel ...
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16409
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The mdio bus number of mv88e6xxx was changed to '0' from '1' and the
"mv88e6xxx-1:<addr>:<speed>" triggers are unavailable now.
Update triggers for "SPEED" LEDs to make working that LEDs again.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16409
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The driver for fixed voltage regulater uses "regulator-fixed" for
compatible string, not "fixed-regulator".
Fixes: 102dc5a625 ("mvebu: add support for FortiGate 50E")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16409
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rename the sysupgrade.tar step to sysupgrade.bin. The sysupgrade.tar is
used in other places and we prefer a sysupgrade.bin instead.
Fixes: fea2264d9f ("ramips: mt7621: Add DNA Valokuitu Plus EX400")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The sysupgrade-tar image build is not defined for this target, do not
add a build instruction for it. The build system will use the definition
from the dna_valokuitu-plus-ex400 board and the build will fail.
This fixes the build of the ramips target.
Fixes: 665c2154ef ("ramips: add basic support for tp-link er605-v2")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Change I2C pin flags to GPIO_ACTIVE_HIGH and change SDA to GPIO1.
On my late production GL-AR750 (purchased 2024):
SCL = GPIO16
SDA = GPIO1
Bug report:
I2C bus doesn't work in GL-AR750
https://github.com/openwrt/openwrt/issues/16319
Signed-off-by: Ryan Salsbury <ryanrs@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16406
Signed-off-by: Robert Marko <robimarko@gmail.com>
Make the patches apply cleanly again.
Fixes: 3660ddb8ab ("generic: ar8216: remove support for Linux before version 6.1")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification is similar to other devices of the MT Stuart series:
* Mediatek MT7988D (3x Cortex-A73, up to 1.8 GHz clock speed)
* 8 GiB eMMC
* 2 GiB DDR4 RAM
* 2500M/1000M/100M LAN port
* 10000M/5000M/2500M/1000M/100M/10M WAN port
* MT7992 Tri-band (2.4G, 5G, 6G) 2T2R+3T3R+3T3R 802.11be Wi-Fi
* Renesas DA14531MOD Bluetooth
* 2 buttons (Reset, Mesh/WPS)
* uC-controlled RGB LED via I2C
* 2x LED for the 2.5G port, 3x LED for the 10G port
* 3.3V-level 115200 baud UART console via 4-pin Dupont connector
exposed at the bottom of the device
* USB-C PD power input
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The legacy swconfig switch driver framework supports kernels older than
Linux 6.6 by using #ifdef'ery with LINUX_VERSION_CODE. Remove all that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Remove folder with DTS files for Linux 6.1 which has already been
dropped.
Fixes: f142ce87d9 ("kirkwood: remove 6.1 support")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Support for Linux 6.1 has already been removed from the armsr target.
Remove left-over patches-6.1 folder as well.
Fixes: fd47fdf527 ("armsr: Remove kernel 6.1 configuration")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Remove left-over config-6.1 files which should have been removed
when removing kernel 6.1 support.
Fixes: f20987c161 ("layerscape: remove kernel 6.1 support")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add the GPIO pin of the PoE passthrough switch on the Aruba AP-303H.
Power is activated when the pin is low. It enables a PSE chip, so power
is only supplied to downstream devices when they are 802.3af/at
compliant devices.
Ensure you use a sufficient power supply when chaining a consuming
device after the AP.
Signed-off-by: David Bauer <mail@david-bauer.net>
Increase QDMA RESV_BUF from 2K to 3K for netsys v2 to match Mediatek SDK.
This helps reduce the possibility of Ethernet transmit timeouts.
Link: 19d8456c30
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The purpose of resetting the TX queue is to reset the
byte and packet count as well as to clear the software
flow control XOFF bit.
MediaTek developers pointed out that netdev_reset_queue would only
resets queue 0 of the network device.
Queues that are not reset may cause unexpected issues.
Packets may stop being sent after reset and "transmit timeout" log may
be displayed.
Import fix from MediaTek's SDK to resolve this issue.
Link: 5746a94456
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Drop config and files for Linux 5.15.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16417
Signed-off-by: Robert Marko <robimarko@gmail.com>
Drop config and files for Linux 5.15.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16417
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds support for netis N6 WiFi 6 router.
Specification
-------------
- SoC : MediaTek MT7621AT, MIPS, 880 MHz
- RAM : 256 MiB
- Flash : NAND 128 MiB (ESMT PSU1GA30DT)
- WLAN : MT7905DAN + MT7975DN
- 2.4 GHz : b/g/n/ax, 574 Mbps, MIMO 2x2
- 5 GHz : a/n/ac/ax, 1201 Mbps, MIMO 2x2
- Ethernet : 10/100/1000 Mbps x5 (1x WAN, 4x LAN)
- USB : 1x 3.0
- UART : 3.3V, 115200n8
- Buttons : 1x Reset
1x WPS
- LEDs : 1x Power (green)
1x System (green)
1x WAN (green)
1x WiFi 2.4 GHz (green), controlled by phy
1x WiFi 5 GHz (green), controlled by phy
1x WPS (green)
1x USB (green)
5x ethernet leds (green), controlled by switch
- Power : 12 VDC, 1.5 A
Installation
------------
1. Update the router using stock firmware web interface and OpenWrt
factory.bin image.
Recovery and return to stock
----------------------------
1. Assign your PC a static IP 192.168.1.2 and connect to the router using
the ethernet cable;
2. Power off the router;
3. Press Reset button, power on the router and wait until ethernet led
start blinking;
4. Release the button;
5. Open http://192.168.1.1/ (N6 System Recovery Mode) in your browser;
6. Upload OpenWrt factory.bin (or stock firmware *.bin) image and proceed
with upgrade.
MAC addresses
-------------
+---------+-------------------+
| | MAC example |
+---------+-------------------+
| LAN | dc:xx:xx:49:xx:04 |
| WAN | dc:xx:xx:49:xx:05 |
| WLAN 2g | dc:xx:xx:19:xx:06 |
| WLAN 5g | dc:xx:xx:79:xx:06 |
+---------+-------------------+
The WLAN MAC prototype was found in 'Factory', 0x4
The LAN MAC was found in 'Factory', 0x7ef20
The WAN MAC was found in 'Factory', 0x7ef26
Known issue
-----------
2.4 GHz WLAN doesn't start with mt76 driver.
Probable reason:
Original Netis N6 EEPROM contains wrong MT_EE_WIFI_CONF value (0xd2).
Other routers with the same WLAN hardware (e.g., Routerich AX1800)
have MT_EE_WIFI_CONF = 0x92.
Workaround (already included in this commit):
Extract EEPROM to a file at the first time boot and change
MT_EE_WIFI_CONF (offset 0x190) value from 0xd2 to 0x92. See
/etc/hotplug.d/firmware/11-mt76-caldata for details.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16322
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This files are executable:
target/linux/ramips/dts/mt7621_openfi_5pro.dts
target/linux/ramips/dts/mt7621_winstars_ws-wn536p3.dts
Has to be fixed.
Fixes: 5560791 ("ramips: add support for OpenFi 5Pro Travel Router")
Fixes: 2da2705 ("ramips: add support for WINSTARS WS-WN536P3")
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16322
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Instead of reading it from flash directly, let U-Boot assign the LAN
MAC address. Set label-mac-device while at it and sort aliases in DT
alphabetically.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Kconfig symbols CONFIG_VIDEO_MICROCHIP_CSI2DC, CONFIG_VIDEO_MICROCHIP_ISC
and CONFIG_VIDEO_MICROCHIP_XISC are missing for sama5 and sama7 causing
the build to abort or waiting for user input. Add the symbols (disabled)
so build with Linux 6.6 succeeds.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fix a typo in the MAC address assignment script affecting SDG-8734.
Fixes: c71b68acdd ("mediatek: filogic: add Adtran SmartRG Mount Stuart series")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware information:
---------------------
- SoC: RTL8393M
- Copper phy: 6×RTL8218B
- Fibre phy: RTL8214FC
- Flash: 32MiB SPI NOR, MX25L25635FMI
- RAM: 128MiB DDR3, Micron MT41K64M16TW-107
- Serial port: ±5V serial port to RJ45, ZT3232 (MAX3232 compatible)
- +370W POE on JG928A model
Note: SFP ports currently non-functional due to missing support for
RTL8214FC on the RTL8393M target.
Updated for Linux 6.6 kernel.
Installation:
-------------
- Initial installation follows same process as HPE 1920-24G (JG924A)
- Based on prior work of Jan Hoffmann <jan@3e8.eu>
- Additional work by Andreas Böhler <dev@aboehler.at>
- PoE updates and tidy-up by Stephen Howell <howels@allthatwemight.be>
Signed-off-by: Stephen Howell <howels@allthatwemight.be>
Now that there is 6.6 support for realtek, lets encourage testing it by
making it default so 5.15 can be dropped ASAP.
Link: https://github.com/openwrt/openwrt/pull/16408
Signed-off-by: Robert Marko <robimarko@gmail.com>
The 'active-low' property was not applied correctly and two fixes
are required to make inverted LEDs work as expected.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The at91 now supports 6.6 kernel as testing.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16058
Signed-off-by: Nick Hainke <vincent@systemli.org>
Remove obsolete patches no longer applicable to the 6.6 kernel.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16058
Signed-off-by: Nick Hainke <vincent@systemli.org>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16058
Signed-off-by: Nick Hainke <vincent@systemli.org>
Remove unnecessary dts files already included in the 6.1 kernel.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16058
Signed-off-by: Nick Hainke <vincent@systemli.org>
Siflower SF19A2890 is an SoC with:
Dual-core MIPS InterAptiv at 800MHz
DDR3 controller
One Gigabit Ethernet MAC with RGMII and IPv4 HNAT engine
Built-in 2x2 11N + 2x2 11AC WiFi radio
USB 2.0 OTG
I2C/SPI/GPIO and various other peripherals
This PR adds support for SF19A2890 EVB with ethernet support.
EVB spec:
Memory: DDR3 128M
Ethernet: RTL8367RB 5-port gigabit switch
Flash: 16M NOR
Others: MicroUSB OTG, LED x 1, Reset button x1
The built image can be flashed using u-boot recovery.
This target is marked as source-only until support for a commercial
router board comes.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This fixes a well-known "LZMA ERROR 1" error on Sercomm NA502s, reported
on the OpneWrt forum [0].
[0] https://forum.openwrt.org/t/206640
Signed-off-by: Andreas Böhler <dev@aboehler.at>
