Add support for the ar71xx supported Netgear WNDR3800CH to ath79.
The device is identical to WNDR3800 except NETGEAR_BOARD_ID.
Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
It has been reported that using the sysupgrade-tar image will trigger
"lzma_decode failed error". The RedBoot bootloader always loads data
from flash till block size boundary, so if there's no padding it'll also
load the beginning of rootfs, and it seems that lzma_decoder can't handle
that garbage data. Previously the script creating combined-image
silently padded the kernel and rootfs, but since sysupgrade-tar doesn't,
pad the default kernel image.
Fixes: 900330f ("ath79: image: retire combined-image for Adtran/Bluesocket
devices")
Cc: Brian Gonyer <bgonyer@gmail.com>
Cc: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This applies alphabetic sorting to devices in image/* files.
For certain cases, this patch deviates from strict sorting, e.g.
to ensure that v10 comes after v9.
While at it, fix an indent and remove some useless empty lines.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Because a bug in handling partial erase blocks in 4.19 kernel, using
sysupgrade images will hard brick devices that use RedBoot bootloader
and have "FIS directory" with "RedBoot config" on the same erase block.
Since flashing the devices from bootloader is safe, and to not cause a
situation where external chip programmer or JTAG is needed, disable
sysupgrade images for affected boards while creating kernel.bin and
rootfs.bin for jjPlus JA76PF2 board, which doesn't have factory image.
To set up the JA76PF2 board follow "Installation" instructions in b3a0c97
("ath79: add support for jjPlus JA76PF2") except the part of loading
initramfs image and using sysupgrade image for flashing (point 6 and 7).
Enter following commands to flash the board from bootloader:
fis init
load -r -b 0x80060000 <openwrt_kernel_image_name>
fis create linux
load -r -b %{FREEMEMLO} <openwrt_rootfs_image_name>
fis create rootfs
fis load -l linux
exec -c ""
For RouterStations use TFTP recovery procedure.
Ref: FS#2428
Cc: Matt Merhar <mattmerhar@protonmail.com>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Now that the md5 check is fixed and metadata present, sysupgrade on
ar71xx will complain about device not being supported by the image.
Since the cause is not matching strings for supported devices add them
accordingly.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This target enforces metadata check so add the necessary information. It
was previously removed because md5 sum check. When using these sysupgrade
images on ar71xx target the check would complain about them not matching.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
During review it slipped by that these devices use combined-image which
should never be used for newly added ones. Therefore switch to
sysupgrade-tar generated images introduced in 8f6f260 ("ath79:
routerstation: prepare to use sysupgrade-tar format image"). The
sysupgrade accepts both images for now so no reression should occur.
Cc: Brian Gonyer <bgonyer@gmail.com>
Cc: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
When adding support in 9ed272fe95 ("ath79: add support for
Comfast WR650AC v1/v2"), IMAGE_SIZE has not been added to device
definition.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
When adding support in abbbecaa73 ("ath79: add support for
Comfast E314N-v2"), IMAGE_SIZE has not been added to device
definition.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
We completely overlooked whitespace errors when reviewing
796ad2f7ef ("ath79: add support for D-Link DIR-842 C3").
Fix them and and also fix Makefile indent for C1/C2.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This is a dual band 11a/11n router with 1x wan and 4x gig lan ports.
There are two versions of this router which can be identified through
the factory web interface, v1 has 128mb ram and a uboot size of 128k,
v2 has 256mb ram and a uboot size of 256k, the remaining hardware and
PCB markings are the same.
Short specification:
SoC: Qualcomm Atheros QCA9558 - 720 MHz
Switch: Atheros AR8327
Second radio : Qualcomm Atheros QCA9880 802.11ac
4 LAN/1 WAN 1000Mps Ethernet
256 MB of RAM (DDR2)
16 MB of FLASH
3x2.4 GHz, 3x5GHz antennas
Steps to install :
Option A : Use vendor UI
Option B (if A is not working) :
(a) Download 'backup' from vendor UI and rename it backup.tar.gz
(b) Open the archive, and update the root password in /etc/shadow by
'$1$9wX3HGfB$X5Sb3kqzzBLdKRUR2kfFd0'
(c) 'Restore' from the archive using the vendor UI. Root password is now
'aaa'
(d) Scp the firwmware to the device:
$ scp <openwrt-sysupgrade>.bin root@192.168.1.1:/
(d) ssh to the device and flash the firmware:
$ cd /
$ mtd -e firmware -r write <openwrt-sysupgrade>.bin firmware
Signed-off-by: Gareth Parker <gareth41@orcon.net.nz>
Signed-off-by: Ding Tengfei <dtf@comfast.cn>
Signed-off-by: Joan Moreau <jom@grosjo.net>
[reformatted commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
Taken code from https://patchwork.ozlabs.org/patch/884850/ that was never
pushed by the author, and adapted to ath79.
The Comfast E314N-V2 is a 2.4 GHz 2x2 radio with a built-in directional
antenna and a second Ethernet port - very similar to the Ubiquiti
NanoStation M2. The Ethernet port features a pass-through PoE capability,
enabled or disabled with a slide switch.
Specifications :
- System-On-Chip: Qualcomm/Atheros QCA9531
- CPU/Speed: 650 MHz
- Flash size: 8 MiB
- RAM: 64 MiB
- 2 Ethernet 1Gbp
- 1 reset button
- 1 switch to choose PoE from LAN or Wan. 48Vdc
- Wifi 2.4 Ghz (b/g/n)
- UART inside the box (3.3V, pins marked on the PCB)
Firmware can be flashed on these units by the following method:
1.) Apply power to the unit
2.) Immediately AFTER applying power, hold down the reset button
3.) The WAN, LAN, and wireless lights will flash - wait three seconds
(three flashes) and then release the button.
4.) After a second, the lights will flutter quickly and the unit will be
visible at 192.168.1.1. A web page will be available to enable quick
and simple uploading and flashing of firmware.
During the boot process, these units also look for a tftp server at
192.168.1.10. If one is present, the firmware can be uploaded as a file
called firmware-auto.bin
Signed-off-by: Joan Moreau <jom@grosjo.net>
[wrapped commit message - fix commit title capitalization]
Signed-off-by: David Bauer <mail@david-bauer.net>
Specifications:
- SoC: AR9341
- RAM: 64M
- Flash: 16M
- Ethernet: 1 * FE port
- WiFi: ar934x-wmac
- Sound: WM8918 DAC
1 * 3.5mm headphone jack
2 * RCA connectors for speakers
1 * SPDIF out
- USB: 1 * USB2.0 port
Flash instruction:
Upload generated factory image via vendor's web interface.
Notes:
A. Audio stuff:
1. Since AR934x, all pins for peripheral blocks can be mapped to
any available GPIOs. We currently don't have a PCM/I2S driver
for AR934x so pinmux for i2s and SPDIF are bound to i2c gpio
node. This should be moved into I2S node when a PCM/I2S driver
is available.
2. The i2c-gpio node is for WM8918. DT binding for it can't be added
currently due to a missing clock from I2S PLL.
B. Factory image:
Image contains a image header and a tar.gz archive.
1. Header: A 288 byte header that has nothing to do with appended
tarball. Format:
0x0-0x7 and 0x18-0x1F: magic values
0x20: Model number string
0xFC: Action string. It's either "update" or "backup"
0x11C: A 1 byte checksum. It's XOR result of 0x8-0x11B
Firmware doesn't care about the rest of the header as long as
checksum result is correct.
The same header is used for backup and update routines so the
magic values and model number can be obtained by generating a
backup bin and grab values from it.
2. Tarball: It contains two files named uImage and rootfs, which
will be flashed into corresponding mtd partition.
Writing a special utility that can only output a fixed binary
blob is overkill so factory image header is placed under
image/bin instead.
C. LED
The wifi led has "Wi-Fi" marked on the case but vendor's firmware
used it as system status indicator. I did the same in this device
support patch.
D. Firmware
Factory u-boot is built without 'savenv' support so it's impossible
to change kernel offset. A 2MB kernel partition won't be enough in
the future. OKLI loader is used here to migrate this problem:
1. add OKLI image magic support into uImage parser.
2. build an OKLI loader, compress it with lzma and add a normal
uImage header.
3. flash the loader to where the original kernel supposed to be.
4. create a uImage firmware using OKLI loader.
5. flash the created firmware to where rootfs supposed to be.
By doing so, u-boot will start OKLI loader, which will then load
the actual kernel at 0x20000.
The kernel partition is 2MB, which is too much for our loader.
To save this space, "mtd-concat" is used here:
1. create a 64K (1 erase block) partition for OKLI loader and
create another partition with the left space.
2. concatenate rootfs and this partition into a virtual flash.
3. use the virtual flash for firmware partition.
Currently OKLI loader is flashed with factory image only.
sysupgrade won't replace it. Since it only has one function
and it works for several years, its unlikely to have some bugs
that requires a replacement.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Hardware spec of DIR-842 C3:
SoC: QCA9563
DRAM: 128MB DDR2
Flash: 16MB SPI-NOR
Switch: QCA8337N
WiFi 5.8GHz: QCA9888
WiFi 2.4Ghz: QCA9563
USB: circuit onboard, but components are not soldered
Flash instructions:
1. Upgrade the factory.bin through the factory web interface or
the u-boot failsafe interface.
The firmware will boot up correctly for the first time.
Do not power off the device after OpenWrt has booted.
Otherwise the u-boot will enter failsafe mode as the checksum
of the firmware has been changed.
2. Upgrade the sysupgrade.bin in OpenWrt.
After upgrading completes the u-boot won't complain about the
firmware checksum and it's OK to use now.
3. If you powered off the device before upgrading the sysupgrade.bin,
just upgrade the factory.bin through the u-boot failsafe interface
and then goto step 2.
Signed-off-by: Perry Melange <isprotejesvalkata@gmail.com>
Hardware spec of DIR-842 C1:
SoC: QCA9563
DRAM: 128MB DDR2
Flash: 16MB SPI-NOR
Switch: QCA8337N
WiFi 5.8GHz: QCA9888
WiFi 2.4Ghz: QCA9563
USB: circuit onboard, but components are not soldered
Flash instructions:
1. Upgrade the factory.bin through the factory web interface or
the u-boot failsafe interface.
The firmware will boot up correctly for the first time.
Do not power off the device after OpenWrt has booted.
Otherwise the u-boot will enter failsafe mode as the checksum
of the firmware has been changed.
2. Upgrade the sysupgrade.bin in OpenWrt.
After upgrading completes the u-boot won't complain about the
firmware checksum and it's OK to use now.
3. If you powered off the device before upgrading the sysupgrade.bin,
just upgrade the factory.bin through the u-boot failsafe interface
and then goto step 2.
Signed-off-by: Jackson Lim <jackcolentern@gmail.com>
[fix whitespace issues]
Signed-off-by: David Bauer <mail@david-bauer.net>
This commit ports support for the ALFA Network AP121F, a pocket-size
router with 1 Ethernet and 2.4 GHz WiFi based on the AR9331 SoC, to the
ath79 target (it was already supported in ar71xx; see commit 0c6165d2
for more details).
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[pepe2k@gmail.com: fixed GPIO polarity, included USB support, changed
DTS nodes order, moved WLAN LED trigger define to DTS, made U-Boot env
partition writable]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Hardware spec of DIR-842 C2:
SoC: QCA9563
DRAM: 128MB DDR2
Flash: 16MB SPI-NOR
Switch: QCA8337N
WiFi 5.8GHz: QCA9888
WiFi 2.4Ghz: QCA9563
USB: 2.0
Flash instructions:
1. Upgrade the factory.bin through the factory web interface or
the u-boot failsafe interface.
The firmware will boot up correctly for the first time.
Do not power off the device after OpenWrt has booted.
Otherwise the u-boot will enter failsafe mode as the checksum
of the firmware has been changed.
2. Upgrade the sysupgrade.bin in OpenWrt.
After upgrading completes the u-boot won't complain about the
firmware checksum and it's OK to use now.
3. If you powered off the device before upgrading the sysupgrade.bin,
just upgrade the factory.bin through the u-boot failsafe interface
and then goto step 2.
Signed-off-by: Jackson Lim <jackcolentern@gmail.com>
[Reword reset-hog comment, fix formatting]
Signed-off-by: David Bauer <mail@david-bauer.net>
Trendnet TEW-823DRU is a dual-band AC1750 router.
The router is based on Qualcomm/Atheros QCA9558 + QCA9880.
Specification:
720 MHz CPU
256 MB of RAM
16 MB of FLASH
3T3R 2.4 GHz
3T3R 5 GHz
5x 10/100/1000 Mbps Ethernet
Firmware can be flashed from the web interface. Tested on 3 routers
with no issues.
Signed-off-by: Pramod Pancha <pancha@vill.com>
[whitespace fixes]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This board was used in dual-band 802.11n enterprise access points, models
BSAP-1800v2 and BSAP-1840, introduced in 2010 by Bluesocket, which was
acquired by Adtran in 2011, who has now EOL'ed them. They differed only in
that the BSAP-1840's antennae were detachable, while the BSAP-1800v2's were
inside the case. They have an external RJ-45 console port, which works with
standard Cisco 72-3383-01 console cables.
Specification:
- System-On-Chip: AR7161
- CPU/Speed: 600 MHz
- Flash-Chip: Macronix MX25L12845E
- Flash size: 16 MiB
- RAM: 64 MiB
- Wireless No1: Lite-On WN2601A card: AR9160/AR9103 2.4GHz 802.11bgn
- Wireless No2: Lite-On WN2502A card: AR9160/AR9106 5GHz 802.11an
- PHY: Vitesse VSC8601, Rev. B
Installation:
1. Connect to the serial console using a terminal that supports YMODEM at
115200 bps, 8 data bits, no parity, 1 stop bit
2. Interrupt the bootloader using its password, which is: r00t
3. Issue the "fis init" command, confirming if prompted
4. Look at the length of the openwrt-ath79-generic-*-squashfs-kernel.bin
file, and substitute it below, instead of where I have "LeNgTh"
5. Issue the following command, and upload this file using YMODEM protocol
load -r -v -b 0x80060000 -m ymodem
6. Issue the following commands, substituting as mentioned above:
fis create -b 0x80060000 -l LeNgTh vmlinux_2
load -r -v -b 0x80100000 -m ymodem
7. Using YMODEM, upload openwrt-ath79-generic-*-squashfs-rootfs.bin
8. Issue the "fis free" command, and for the first range in its response,
use a hexadecimal calculator to subtract the start from the end in order
to substitute it below, with the leading "0x" to specify it in
hexadecimal, instead of where I have "LeNgTh"
9. Issue the following commands, substituting as mentioned above:
fis create -b 0x80100000 -l LeNgTh -e 0 -r 0 rootfs
reset
10.Wait for the status LED to go solid green
Tested-by: Brian Gonyer <bgonyer@gmail.com>
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[fixed obsolete $ARGV in platform_do_upgrade]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Specifications:
- SoC: AR9344
- RAM: 128MB
- Flash: 2 * 16MB (MX25L12845)
- Ethernet: 2 * FE LAN & 1 * FE WAN
- WiFi: 2.4G: AR9344 5G: QCA9882
Flash instruction:
1. Hold reset and power up the router
2. Set your IP to 192.168.1.x
3. Open 192.168.1.1 and upload the generated *factory* firmware
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Hardware
--------
CPU: Qualcomm Atheros QCA9558
RAM: 128M DDR2
FLASH: 16MiB
ETH: 1x Atheros AR8035 (PoE in)
WiFi2: QCA9558 3T3R
WiFi5: QCA9880 3T3R
BTN: 1x Reset
LED: 1x LED Power (non-controllable)
1x LED Status (internal)
1x LED LAN (controlled by PHY)
1x LED WLAN
BEEP: 1x GPIO attached piezo beeper
UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad)
Header is located next to external-LED header.
Installation
------------
Make sure you set a password for the root user as prompted on first
setup!
1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.
2. Install OpenWRT with
> sysupgrade -n -F /tmp/<openwrt-image-name>
Signed-off-by: David Bauer <mail@david-bauer.net>
The Etactica EG200 is the only device in ath79 despite nand
target that lacks IMAGE_SIZE.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This allows the definition of DEVICE_VENDOR, DEVICE_MODEL and
DEVICE_VARIANT. All three are merged together to look the same as the
current DEVICE_TITLE. Also, if DEVICE_TITLE is set it's directly used as
a *fallback* for devices which weren't upgraded yet.
This is based on the work of @sudhanshu16.
The motivation is to create JSON files based on provided metadata,
needing clear differentiation between vendor, model and revision.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Specifications:
- Atheros AR9331 (400 MHz)
- 64 MB of RAM (DDR2)
- 16 MB of Flash (SPI)
- 1T1R 2.4 Wlan (AR9331)
- 2x 10/100 Mbps Ethernet
- 3x LEDs, 1x gpio button
- 1x USB 2.0, 5V
- UART over usb, 115200n8
Upgrading from ar71xx target:
- Put image into board:
scp openwrt-ath79-generic-8dev_carambola2-squashfs-sysupgrade.bin \
root@192.168.1.1/tmp/
- Run sysupgrade
sysupgrade /tmp/sysupgrade.bin
Upgrading from u-boot:
- Set up tftp server with sysupgrade.bin image
- Go to u-boot (reboot and press ESC when prompted)
- Set TFTP server IP
setenv serverip 192.168.1.254
- Set device ip from same subnet
setenv ipaddr 192.168.1.1
- Copy new firmware to board
tftpboot 0x81000000 sysupgrade.bin
- erase flash
erase 0x9f050000 +${filesize}
- flash firmware
cp.b 0x81000000 0x9f050000 ${filesize}
- Reset board
reset
Signed-off-by: Rytis Zigmantavičius <rytis.z@8devices.com>
[wrapped long line in commit description, whitespace and art address
fix in DTS, keep default lan/wan setup, removed -n in sysupgrade]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
ZBT-WD323 is a dual-LTE router based on AR9344. The detailed
specifications are:
* AR9344 560MHz/450MHz/225MHz (CPU/DDR/AHN).
* 128 MB RAM
* 16MB of flash(SPI-NOR, 22MHz)
* 1x 2.4GHz wifi (Atheros AR9340)
* 3x 10/100Mbos Ethernet (AR8229)
* 1x USB2.0 port
* 2x miniPCIe-slots (USB2.0 only)
* 2x SIM slots (standard size)
* 4x LEDs (1 gpio controlled)
* 1x reset button
* 1x 10 pin terminal block (RS232, RS485, 4x GPIO)
* 2x CP210x UART bridge controllers (used for RS232 and RS485)
* 1x 2 pin 5mm industrial interface (input voltage 12V~36V)
* 1x DC jack
* 1x RTC (PCF8563)
Tested:
- Ethernet switch
- Wifi
- USB port
- MiniPCIe-slots (+ SIM slots)
- Sysupgrade
- Reset button
- RS232
Intallation and recovery:
The board ships with OpenWRT, but sysupgrade does not work as a
different firmware format than what is expected is generated. The
easiest way to install (and recover) the router, is to use the
web-interface provided by the bootloader (Breed).
While the interface is in Chinese, it is easy to use. First, in order to
access the interface, you need to hold down the reset button for around
five seconds. Then, go to 192.168.1.1 in your browser. Click on the
second item in the list on the left to access the recovery page. The
second item on the next page is where you select the firmware. Select
the menu item containing "Atheros SDK" and "16MB" in the dropdown close
to the buttom, and click on the button at the bottom to start
installation/recovery.
Notes:
* RS232 is available on /dev/ttyUSB0 and RS485 on /dev/ttyUSB1
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
[removed unused poll-interval from gpio-keys, i2c-gpio 4.19 compat]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
SoC: AR9344
RAM: 128MB
Flash: 16MiB Winbond 25Q128BVFG SPI NOR
5GHz WiFi: AR9380 PCIe 3x3:3 802.11n
2.4GHz WiFi: AR9344 (SoC) AHB 2x2:2 802.11n
5x Gigabit ethernet via AR8327N switch (green + amber LEDs)
2x USB 2.0 via GL850G hub
4x front LEDs from SoC GPIO
1x front WPS button from SoC GPIO
1x bottom reset button from SoC GPIO
Known issues:
AR8327N LEDs only have default functionality, not presented in sysfs.
This is a regression from ar71xx.
UART header JP1, 115200 no parity 1 stop
TX
GND
VCC
(N/P)
RX
See https://openwrt.org/toh/wd/n750 for flashing detail.
Procedures unchanged from ar71xx.
Tested sysupgrade + factory flash from WD Emergency Recovery
Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
The GL.iNet AR750S USB and microSD port is currently not working out of
the box. GPIO 7 is used to control the power of the USB port. Add GPIO
7 as a fixed-regulator for the port. Also add &usb1 to DTS to get the
microSD port to work.
Signed-off-by: Alexander Wördekemper <alexwoerde@web.de>
SoC: Atheros AR7161-8C1A @ 680 MHz
RAM: 128MB - 2x Etron Technology EM6AB160TSA-5G
NOR: 16MB - 1x MXIC MX25L12845EMI-10G (SPI-NOR)
WI1: Atheros AR9223-AC1A 802.11bgn
WI2: Atheros AR9220-AC1A 802.11an
ETH: Atheros AR8021-BL1E + PoE
LED: Dual-Color Power/Status, Ethernet, WLAN2G and WLAN5G
BTN: 1 x Reset
I2C: AT97SC4303s TPM (needs driver!)
CON: RS232-level 8P8C/RJ45 Console Port - 9600 Baud
Factory installation:
- Needs a u-boot replacement. See Wiki for
information on how to do a in-circut flash with
a SPI-Flasher like a CH314A or flashrom. Wiki page
can be found at https://openwrt.org/toh/aruba/aruba_ap-105
- Be careful when dis- and reassembling the device to
not squish any of the antenna cables in the process!
- Be sure to make a full 16 MiB backup of your device
before flashing the new u-boot! This is needed if you
ever have interest in reverting back to stock firmware.
Not working:
- TPM (needs a driver)
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Specification:
- Qualcomm Atheros SoC QCA9558
- 720/600/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 1x 10/100/1000 Mbps Ethernet
- 3T3R 2.4 GHz (QCA9558 WMAC)
- 3T3R 5.8 Ghz (QCA9880-BR4A, Senao PCE4553AH)
https://fccid.io/A8J-ECB1750
Tested and working:
- lan, wireless, leds, sysupgrade (tftp)
Flash instructions:
1.) tftp recovery
- use a 1GbE switch or direct attached 1GbE link
- setup client ip address 192.168.1.10 and start tftpd
- save "openwrt-ath79-generic-engenius_ecb1750-initramfs-kernel.bin" as "ap.bin" in tfpd root directory
- plugin powercord and hold reset button 10secs.. "ap.bin" will be downloaded and executed
- afterwards login via ssh and do a sysuprade
2.) oem webinterface factory install (not tested)
Use normal webinterface upgrade page und select "openwrt-ath79-generic-engenius_ecb1750-squashfs-factory.bin".
3.) oem webinterface command injection
OEM Firmware already running OpenWrt (Attitude Adjustment 12.09).
Use OEM webinterface and command injection. See wiki for details.
https://openwrt.org/toh/engenius/engenius_ecb1750_1
Signed-off-by: sven friedmann <sf.openwrt@okay.ms>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[use interrupt-driven "gpio-keys" binding]
I-O DATA ETG3-R is a wired router. So wireless-related packages are
unnecessary and remove those packages from default configuration to
reduce flash usage.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This is sold as a dual-band 802.11ac range extender. It has a sliding
switch for Extender mode or Access Point mode, a WPS button, a recessed
Reset button, a hard-power button, and a multitude of LED's, some
multiplexed via an NXP 74AHC164D chip. The internal serial header pinout is
Vcc, Tx, Rx, GND, with GND closest to the corner of the board. You may
connect at 115200 bps, 8 data bits, no parity, 1 stop bit.
Specification:
- System-On-Chip: QCA9558
- CPU/Speed: 720 MHz
- Flash-Chip: Winbond 25Q128FVSG
- Flash size: 16 MiB
- RAM: 128 MiB
- Wireless No1: QCA9558 on-chip 2.4GHz 802.11bgn, 3x3
- Wireless No2: QCA99x0 chip 5GHz 802.11an+ac, 4x4
- PHY: Atheros AR8035-A
Installation:
If you can get to the stock firmware's firmware upgrade option, just feed
it the factory.img and boot as usual. As an alternative, TFTP the
factory.img to the bootloader.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[whitespace fix in DTS and reorder of make variables]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Remove Netgear-specific image build variables which are set to the same
value.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[reordering of variables, removed stray newline]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
SOC: Qualcomm Atheros QCA9558
RAM: 128MB
FLASH: 16MB (Macronix MX25L12845EMI-10G)
WLAN1: QCA9558 2.4GHz 802.11bgn 3SS
WLAN2: QCA9880 5GHz 802.11ac 3SS
LED: Power, LAN1, LAN2, 2.4GHz, 5GHz
Serial:Next to SPI Flash,
Pinout is 3V3 - GND - TX - RX (Square Pin is 3V3)
The Serial setting is 115200-8-N-1
INSTALLATION:
1. Serve an OpenWrt ramdisk image named "ursus.bin".
Set your IP-address to 192.168.100.8/24.
2. Connect to the serial. Power up the device and interrupt
the boot process.
3. Set the correct bootcmd with
> setenv bootcmd run bootcmd_1
> saveenv
4. Run
> tftpboot 0x81000000 ursus.bin
> bootm 0x81000000
5. Wait for OpenWrt to boot up.
6. Transfer OpenWrt sysupdate image and flash via sysupgrade.
Signed-off-by: Markus Scheck <markus.scheck1@gmail.com>
Tested-by: David Bauer <mail@david-bauer.net>
[whitespace fix, renamed LED labels and SoC type fix]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
COMFAST CF-E5/E7 is a outdoor 4G LTE AP with PoE support, based on
Qualcomm/Atheros QCA9531.
Short specification:
2x 10/100 Mbps Ethernet, with 24v PoE support
64 MB of RAM (DDR2)
16 MB of FLASH (SPI)
2T2R 2.4 GHz, 802.11b/g/n
built-in 1x 3 dBi antennas
output power (max): 80 mW (19 dBm)
Qucetel EC20 LTE MODULE(1x external detachable antenna)
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Ding Tengfei <dtf@comfast.cn>
[commit subject fix]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
jjPlus JA76PF2 (marketed as IntellusPro2) is a network embedded board.
Specification
SoC: Atheros AR7161
RAM: 64 MB DDR
Flash: 16 MB SPI NOR
Ethernet: 2x 10/100/1000 Mbps AR8316
LAN (CN11), WAN/PoE (CN6 - close to power barrel
connector, 48 V)
MiniPCI: 2x
LEDS: 4x, which 3 are GPIO controlled
Buttons: 2x GPIO controlled
Reset (SW1, closer to ethernet ports), WPS (SW2)
Serial: 1x (only RX and TX are wired)
baud: 115200, parity: none, flow control: none
Currently there is one caveat compared to ar71xx target images as the
MAC addresses are random on every reboot. To remedy this one needs to
store the WAN MAC address in RedBoot configuration. OpenWrt on first
boot, after flashing, will read out the address and assign proper ones
to both WAN and LAN ports. It is iportant to NOT keep the old
configuration when doing sysupgrade from ar71xx.
Upgrading from OpenWrt ar71xx image
1. Connect to serial port,
2. Download OpenWrt sysupgrade image to /tmp directory and flash it
with:
sysupgrade -n <openwrt_sysupgrade_image_name>
3. After writing new image OpenWrt will reboot, now interrupt boot
process and enter RedBoot (bootloader) command line by pressing
Ctrl+C,
4. Enter following commands (replace variable accordingly),
set_mac (to view MAC addresses)
alias ethaddr <wan_port_mac_adress>
(confirm storing the value by inputting y and pressing Enter)
reset
5. Now board should restart and boot OpenWrt with proper MAC addresses.
Installation
1. Prepare TFTP server with OpenWrt initramfs image,
2. Connect to WAN ethernet port,
3. Connect to serial port,
4. Power on the board and enter RedBoot (bootloader) command line by
pressing Ctrl+C,
5. Enter following commands (replace variables accordingly):
set_mac (to view MAC addresses)
alias ethaddr <wan_port_mac_address>
(confirm storing the value by inputting y and pressing Enter)
ip_adress -l <board_ip_adress>/24 -h <tftp_server_ip_adress>
load -r -b 0x80060000 <openwrt_initramfs_image_name>
exec -c ""
6. Now board should boot OpenWrt initramfs image,
7. Download OpenWrt sysupgrade image to /tmp directory and flash it
with:
sysupgrade <openwrt_sysupgrade_image_name>
8. Wait few minutes, after the D2 LED will stop blinking, the board
is ready for configuration.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
EnGenius EPG5000 (v1.0.0, marketed as IoT Gateway) is a dual band
wireless router.
Specification
SoC: Qualcomm Atheros QCA9558
RAM: 256 MB DDR2
Flash: 16 MB SPI NOR
WIFI: 2.4 GHz 3T3R integrated
5 GHz 3T3R QCA9880 Mini PCIe card
Ethernet: 5x 10/100/1000 Mbps QCA8337N
USB: 1x 2.0
LEDS: 4x GPIO controlled
Buttons: 2x GPIO controlled
UART: 4 pin header, starting count from white triangle on PCB
1. VCC 3.3V, 2. GND, 3. TX, 4. RX
baud: 115200, parity: none, flow control: none
Installation
1. Connect to one of LAN (yellow) ethernet ports,
2. Open router configuration interface,
3. Go to Tools > Firmware,
4. Select OpenWrt factory image with dlf extension and hit Apply,
5. Wait few minutes, after the Power LED will stop blinking, the router
is ready for configuration.
Alternative installation
1. Prepare TFTP server with OpenWrt sysupgrade image,
2. Connect to one of LAN (yellow) ethernet ports,
3. Connect to UART port (leaving out VCC pin!),
4. Power on router,
5. When asked to enter a number 1 or 3 hit 2, this will select flashing
image from TFTP server option,
6. You'll be prompted to enter TFTP server ip (default is 192.168.99.8),
then router ip (default is 192.168.99.9) and for last, image name
downloaded from TFTP server (default is uImageESR1200_1750),
7. After providing all information U-Boot will start flashing the image,
You can observe progress on console, it'll take few minutes and when
the Power LED will stop blinking, router is ready for configuration.
Additional information
If connected to UART, when prompted for number on boot, one can enter
number 4 to open bootloader (U-Boot) command line.
OEM firmware shell password is: aigo3d0a0tdagr
useful for creating backup of original firmware.
When doing upgrade from OpenWrt ar71xx image, it is recomended to not keep
the old configuration.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
AR300M-Lite is single-Ethernet variant of the AR300M series
Its eth0 would otherwise be assigned to the WAN interface
making it unreachable firstboot or failsafe.
Installation instructions from OEM (OpenWrt variant):
* Install sysupgrade.bin using OEM's "Advanced" GUI (LuCI),
* Do not preserve settings
* Access rebooted device via Ethernet at OpenWrt default address
Add previously missing LED defaults for all three variants;
-nand, -nor, -lite to the definitions in 01_leds
Non-lite variants thanks to Andreas Ziegler
https://patchwork.ozlabs.org/patch/1049396/
Runtime-tested: GL.iNet AR300M-Lite
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Hardware
--------
SOC: QCA9558
RAM: 128M DDR2
Flash: 16MiB SPI-NOR
ETH: QCA8337N: 2x 10/100/1000 PoE and PoE pass-through
WiFi2: QCA9558 (bgn) 2T2R
WiFi5: 2x mPCIE with AR9582 (an) 2T2R
BTN: 1x Reset
GPIO: multiple GPIO on header, PoE passthrough enable
UART: 3.3V 115200 8N1 header on the board
WDG: ATTiny13 watchdog
JTAG: header on the board
USB: 1x connector and 1x header on the board
PoE: 10-32V input in ETH port 1, passthrough in port 2
mPCIE: 2x populated with radios (but replaceable)
OpenWrt is preinstalled from factory. To install use <your-image>-sysupgade.bin
using the web interface or with sysupgrade -n.
Flash from bootloader (in case failsafe does not work)
1. Connect the LibreRouter with a serial adapter (TTL voltage) to the UART
header in the board.
2. Connect an ETH cable and configure static ip addres 192.168.1.10/24
3. Turn on the device and stop the bootloader sending any key through the serial
interface.
4. Use a TFTP server to serve <your image>-sysupgrade.bin file.
5. Execute the following commands at the bootloader prompt:
ath> tftp 82000000 <your image>-sysupgrade.bin
ath> erase 0x9f050000 +$filesize
ath> cp.b 0x82000000 0x9f050000 $filesize
ath> bootm 0x9f050000
More docs
* Bootloader https://github.com/librerouterorg/u-boot
* Board details (schematics, gerbers): https://github.com/librerouterorg/board
Signed-off-by: Santiago Piccinini <spiccinini@altermundi.net>
YunCore A770 is a ceiling AC750 AP with 2 Fast Ethernet ports, PoE
(802.3at) support, based on QCA9531 + QCA9887.
Specification:
- 650/597/216 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of flash (SPI NOR)
- 2x 10/100 Mbps Ethernet (PoE 802.3at support in WAN port)
- 2T2R 2.4 GHz (QCA9531), with ext. PA and LNA
- 1T1R 5 GHz (QCA9887), with ext. FEM (SKY85728-11)
- 2x regular LED, 1x RGB LED (all driven by GPIO)
- 1x button (reset)
- DC jack for main power input (12 V)
- UART header on PCB
Flash instruction:
1. First, gain root access to the device, following below steps:
- Login into web gui (default password/IP: admin/192.168.188.253).
- Go to 'Advanced' -> 'Management' -> 'System' and download backup of
configuration (bakfile.bin).
- Open the file as tar.gz archive, edit/update 'shadow' file and change
hash of root password to something known.
- Repack the archive, rename it back to 'bakfile.bin' and use to
restore configuration of the device.
- After that, device will reboot and can be accessed over SSH.
2. Then, install OpenWrt:
- Login over SSH and issue command:
fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
- Upload 'sysupgrade' image and install it (only if previous command
succeeded) with command: 'sysupgrade -n -F openwrt-...'.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This patch adds support for the COMFAST CF-E120A v3, an outdoor wireless
CPE with two Ethernet ports and a 802.11an radio.
Specifications:
- AR9344 SoC
- 535/400/267 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, both with PoE-in support
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 5 GHz, up to 25 dBm
- 11 dBi built-in antenna
- POWER/LAN/WAN/WLAN green LEDs
- 4x RSSI LEDs (2x red, 2x green)
- UART (115200 8N1) and GPIO (J9) headers on PCB
Flashing instructions:
The original firmware is based on OpenWrt so a sysupgrade image can be
installed via the stock web GUI. Settings from the original firmware
will be saved and restored on the new one, so a factory reset will be
needed. To do so, once the new firmware is flashed, enter into failsafe
mode by pressing the reset button several times during the boot
process, while while the WAN LED flashes, until it starts flashing
faster. Once in failsafe mode, perform a factory reset as usual.
The U-boot bootloader contains a recovery HTTP server to upload the
firmware. Push the reset button while powering the device on and
keep it pressed for >10 seconds. The recovery page will be at
http://192.168.1.1
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
This adds the support-list entry the AVM FRITZ!Box 4020 expects in the
ar71xx target to allow non-forced sysupgrades from ar71xx to ath79.
Signed-off-by: David Bauer <mail@david-bauer.net>
I-O DATA WN-AC1600DGR is a 2.4/5 GHz band 11ac router, based on
Qualcomm Atheros QCA9557.
Specification:
- SoC: Qualcomm Atheros QCA9557
- RAM: 128 MB
- Flash: 16 MB
- WLAN: 2.4/5 GHz
- 2.4 GHz: 2T2R (SoC internal)
- 5 GHz: 3T3R (QCA9880)
- Ethernet: 5x 10/100/1000 Mbps
- Switch: QCA8337N
- LED/key: 6x/6x(4x buttons, 1x slide switch)
- UART: through-hole on PCB
- Vcc, GND, TX, RX from ethernet port side
- 115200n8
Flash instruction using factory image:
1. Connect the computer to the LAN port of WN-AC1600DGR
2. Connect power cable to WN-AC1600DGR and turn on it
3. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing
Alternative flash instruction using initramfs image:
1. Prepare a computer and TFTP server software with the IP address
"192.168.99.8" and renamed OpenWrt initramfs image
"uImageWN-AC1600DGR"
2. Connect between WN-AC1600DGR and the computer with UART
3. Connect power cable to WN-AC1600DGR, press "4" on the serial
console and enter the U-Boot console
4. execute "tftpboot" command on the console and download initramfs
image from the TFTP server
5. execute "bootm" command and boot OpenWrt
6. On initramfs image, download the sysupgrade image to the device
and perform sysupgrade with it
7. Wait ~150 seconds to complete flashing
This commit also removes unnecessary "qca,no-eeprom" property from
the ath10k wifi node.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Hardware
--------
CPU: Qualcomm Atheros QCA9561
RAM: 64M DDR2
FLASH: 16M SPI-NOR
ETH: 1x WAN - 2x LAN
WiFi: QCA9561 3T3R
BTN: 1x Reset - 1x WPS
LED: 1x Blue - 1x Red - 1x Yellow
UART: TX - GND - RX - VCC (From ethernet port)
115200n8 - 3.3V
Installation
------------
1. Connect to the device via UART.
2. Interrupt the U-Boot on power-on by pressing enter when prompted.
3. Connect you computer to one of the routers LAN ports.
Assign yourself the IP 192.168.31.10/24.
Copy the OpenWRT initramfs image to a tftp server root directory.
Rename the image to 'x4q.bin'.
4. Load the initramfs image to the router by executing following command
in U-Boot. The image will boot afterwards.
> tftpboot 0x81000000 x4q.bin; bootm
5. SCP the sysupgrade-image into '/tmp'.
Remember to assign yourself an IP in 192.168.1.0/24 for this step!
6. Install OpenWRT permanently by executing
> sysupgrade -n /tmp/<OpenWRT-sysupgrade-image>
Signed-off-by: David Bauer <mail@david-bauer.net>
Hardware
--------
CPU: Qualcomm Atheros QCA9558
RAM: 128M DDR2
FLASH: 16MiB
ETH: 1x Atheros AR8035 (PoE in)
1x Atheros AR8033
WiFi2: QCA9558 3T3R (SiGE SE2565T 2.4 GHz power amp x3)
WiFi5: QCA9880 3T3R (Skyworks 5003L1 5 GHz power amp x3)
BTN: 1x Reset
1x WPS
1x USB eject
LED: 1x LED blue
1x LED red
BEEP: 1x GPIO attached piezo beeper
UART: 3.3V GND TX RX (115200-N-8) (3.3V is pin closest to rear ports)
Dupont 4 pin header
Rear RJ45 serial port non-functional
USB: 1x v2.0
Installation
------------
Make sure you set a password for the root user as prompted on first
setup!
1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password previously set in the web interface.
2. Install OpenWRT with
> sysupgrade -n -F /tmp/<openwrt-image-name>
Signed-off-by: Django Armstrong <iamdjango@hotmail.com>
Hardware
--------
CPU: Qualcomm Atheros QCA9558
RAM: 128M DDR2
FLASH: 16MiB
ETH: 1x Atheros AR8035 (PoE in)
WiFi2: QCA9558 2T2R
WiFi5: QCA9880 2T2R
BTN: 1x Reset
LED: 1x LED blue
1x LED red
BEEP: 1x GPIO attached piezo beeper
UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad)
Header is located next to reset-button
Installation
------------
Make sure you set a password for the root user as prompted on first
setup!
1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.
2. Install OpenWRT with
> sysupgrade -n -F /tmp/<openwrt-image-name>
Signed-off-by: David Bauer <mail@david-bauer.net>
Hardware
--------
CPU: Qualcomm Atheros QCA9558
RAM: 128M DDR2
FLASH: 16MiB
ETH: 1x Atheros AR8035 (PoE in)
WiFi2: QCA9558 3T3R
WiFi5: QCA9880 3T3R
BTN: 1x Reset
LED: 1x LED blue
1x LED red
BEEP: 1x GPIO attached piezo beeper
UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad)
Header is located next to reset-button
Installation
------------
Make sure you set a password for the root user as prompted on first
setup!
1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.
2. Install OpenWRT with
> sysupgrade -n -F /tmp/<openwrt-image-name>
Signed-off-by: David Bauer <mail@david-bauer.net>
Replace the code with a more readable version. Rename the recipe
to reflect the real usecase.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch adds support for the COMFAST CF-E110N, an outdoor wireless
CPE with two Ethernet ports and a 802.11bgn radio.
Specifications:
- 650/400/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, both with PoE-in support
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, up to 26 dBm
- 11 dBi built-in antenna
- POWER/LAN/WAN/WLAN green LEDs
- 4x RSSI LEDs (2x red, 2x green)
- UART (115200 8N1) and GPIO (J9) headers on PCB
Flashing instructions:
The original firmware is based on OpenWrt so a sysupgrade image can be
installed via the stock web GUI. Settings from the original firmware
will be saved and restored on the new want, so a factory reset will be
needed: once the new firmware is flashed, perform the factory reset by
pushing the reset button several times during the boot process, while the
WAN LED flashes, until it starts flashing quicker.
The U-boot bootloader contains a recovery HTTP server to upload the
firmware. Push the reset button while powering the device on and keep it
pressed for >10 seconds. The recovery page will be at http://192.168.1.1
Notes:
The device is advertised, sold and labeled as "CF-E110N", but the
bootloader and the stock firmware identify it as "v2".
Acknowledgments:
Petr Štetiar <ynezz@true.cz>
Sebastian Kemper <sebastian_ml@gmx.net>
Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[drop unused labels from devicetree source file]
Signed-off-by: Mathias Kresin <dev@kresin.me>
EnGenius EWS511AP is a wireless managed wall AP with PoE support,
based on Qualcomm/Atheros QCA9531(Honeybee) + QCA9887.
Short specification:
- 128MB of RAM
- 16 MB of SPI FLASH
- 2T2R 2.4 GHz (QCA9531), 802.11b/g/n
- 1T1R 5 GHz (QCA9887), 802.11ac/n/a
- 2x 10/100 Mbps Ethernet (one port with PoE support)
- 1x Power LED, 2x LAN LEDs, 1x WLAN 2.4G LED, 1x WLAN 5G LED
- 1x RESET button
- built-in watchdog chipset
Flash instruction:
From EnGenius firmware to OpenWrt firmware:
Original firmware is based on QSDK.
Use sysupgrade firmware directly in vendor GUI.
Reset to factory default is necessary.
From OpenWrt firmware to EnGenius firmware:
1. Setup a TFTP server on your computer and configure static IP to 192.168.99.8
Put the OpenWrt firmware in the root directory on your computer.
2. Power up EWS511AP. Press 4 and then press any key to enter u-boot.
3. Download OpenWrt firmware
(ath)> tftpboot 0x80060000 ${dir}"openwrt-ath79-generic-engenius_ews511ap-squashfs-sysupgrade.bin"
4. Flash the firmware
(ath)> erase 0x9f060000 +f50000
(ath)> cp.b $fileaddr 0x9f060000 $filesize
5. Reboot
(ath)> reset
Signed-off-by: Guan-Hong Lin <GH.Lin@senao.com>
This device is called GL-AR300M, therefore rename the board(s)
to 'gl-ar300m-nor' and 'gl-ar300m-nand'
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
[change boardname in uboot envtools as well, don't use wildcards for
boardname]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Right now this patch adds nor image generation only. NAND image
generation is not supportet at the moment.
Furtheremore support for the MicroSD port is not implemented as of now.
Specification:
- SOC: QCA9563 (775MHz)
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 128 MiB DDR2
- Ethernet: 2x 1Gbps LAN + 1x 1Gbps WAN
- Wireless: 2.4GHz (bgn) and 5GHz (ac)
- USB: 1x USB 2.0 port
- Button: 1x switch button, 1x reset button
- LED: 3x LEDS (green)
- Another LED can be accessed on GPIO 7 if soldered
Flash instruction:
- Set static ip to 192.168.1.2
- Unplug the power cord
- Hold reset button
- Plug power back in
- Right led will flash 5 times
- Release reset button
- Browse to 192.168.1.1
- Choose sysupgrade image in NOR-flash section
- Press "update nor firmware"
- After successful transfer unplug network cable before device restarts
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[resolve merge conflicts, rename buttons, use switch input type for mode
switch]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Hardware spec of DIR-859 A1:
SoC: QCA9563
DRAM: 64MB DDR2
Flash: 16MB SPI-NOR
Switch: QCA8337N
WiFi 5.8GHz: QCA9880
USB is supported on the PCB but not connected.
Flash instructions:
1. Upgrade the factory.bin through the factory web interface or the u-boot
failsafe interface.
The firmware will boot up correctly for the first time.
Do not power off the device after OpenWrt has booted. Otherwise the u-boot
will enter failsafe mode as the checksum of the firmware has been changed.
2. Upgrade the sysupgrade.bin in OpenWrt.
After upgrading completes the u-boot won't complain about the firmware
checksum and it's OK to use now.
3. If you powered off the device before upgrading the sysupgrade.bin, just
upgrade the factory.bin through the u-boot failsafe interface and then goto
step 2.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
[squash commits, use common seama recipes, sync factory image recipe
with ramips version]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Hardware
--------
CPU: Qualcomm Atheros QCA9558
RAM: 128M DDR2
FLASH: 16MiB
ETH: 1x Atheros AR8035 (PoE in)
WiFi2: QCA9558 3T3R
WiFi5: QCA9880 3T3R
BTN: 1x Reset
LED: 1x LED blue
1x LED red
BEEP: 1x GPIO attached piezo beeper
UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad)
Header is located next to reset-button
There is also a Micro-B USB-port present but this only seems to be a
dummy as the circuit next to it is not present (at least in my unit).
It is also not mentioned in the devolo manual.
Installation
------------
Make sure you set a password for the root user as prompted on first
setup!
1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.
2. Install OpenWRT with
> sysupgrade -n -F /tmp/<openwrt-image-name>
Signed-off-by: David Bauer <mail@david-bauer.net>
Hardware
--------
CPU: Qualcomm Atheros QCA9558
RAM: 128M DDR2
FLASH: 16MiB
ETH: 1x Atheros AR8035 (PoE in)
1x Atheros AR8033
WiFi2: QCA9558 2T2R
WiFi5: QCA9880 2T2R
BTN: 1x Reset
LED: 1x LED blue
1x LED red
BEEP: 1x GPIO attached piezo beeper
UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad)
Header is located next to reset-button
Installation
------------
Make sure you set a password for the root user as prompted on first
setup!
1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.
2. Install OpenWRT with
> sysupgrade -n -F /tmp/<openwrt-image-name>
Signed-off-by: David Bauer <mail@david-bauer.net>
NEC Aterm WG800HP is a 2.4/5 GHz band 11ac router, based on Qualcomm
Atheros QCA9563.
Specification:
- Qualcomm Atheros QCA9563
- 64 MB of RAM (DDR2)
- 8 MB of Flash (SPI-NOR)
- 2.4/5 GHz wifi
- 2.4 GHz: 2T2R (SoC internal)
- 5 GHz: 1T1R (QCA9887)
- 4x 10/100/1000 Mbps Ethernet
- 8x LEDs, 3x keys (2x buttons, 1x slide-switch)
- UART through-hole on PCB (J2)
- Vcc, GND, NC, TX, RX from SoC side
- 115200n8
Flash instruction using factory image:
1. Connect the computer to the LAN port on WG800HP
2. Connect power cable to WG800HP and turn on it
3. Access to "http://192.168.10.1/" and open firmware update page
("ファームウェア更新")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Use pad-offset and append-string to create the cameo factory images for
the D-LINK DIR-825 C1/DIR-835 A1 factory images.
Tested-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Since commit 61b5b4971e ("mac80211: make ath10k-ct the default ath10k")
select ath10k-ct and the -ct firmwares by default.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This commit ports both dir-825-c1 and dir-835-a1 from ar71xx to ath79.
They're pretty much identical, except dir-835-a1 has less LEDs.
The routers come with 128 MByte of RAM and 16 MBytes of flash and sport
2.4GHz and 5.0GHz wireless. Both routers have entries already in
OpenWrt's TOH. Please check there for more information on these
antiquities.
https://openwrt.org/toh/hwdata/d-link/d-link_dir-825_c1https://openwrt.org/toh/hwdata/d-link/d-link_dir-835_a1
Installation:
1. Connect to the web interface of the vendor firmware (usually
listening on 192.168.0.1).
2. Go to "Tools", then "Firmware".
3. In the "Firmware Upgrade" box click "Browse".
4. Select the OpenWrt factory image for your router.
5. Click "Upload", confirm the popups if you agree to flash the file you
selected.
6. Wait for firmware upgrade to complete. It takes about 5 minutes.
Run-tested on dir-825-c1. dir-835-a1 should work as well, but I don't
have this router so I can't confirm.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [trivial changes]
I-O DATA WN-AG300DGR is a 2T2R 2.4/5 GHz 11n router, based on Atheros
AR1022.
WN-AG300DGR does not have an LED to indicates power or system status,
I set "router" LED as OpenWrt status LED.
There is no eeprom data for 5 GHz wlan in "art" partition.
Specification:
- Atheros AR1022
- 64 MB of RAM (DDR2)
- 8 MB of Flash (SPI-NOR)
- 2T2R 2.4/5GHz wifi
- 2.4 GHz: SoC internal
- 5 GHz: Atheros AR93x2
- 5x 10/100/1000 Mbps Ethernet
- 6x LEDs, 6x keys (4x buttons, 1x slide switch)
- 1x USB 2.0 Type-A
- UART through-hole on PCB
- Vcc, GND, TX, RX from ethernet port side
- 115200n8
Flash instruction using factory image:
1. Connect the computer to the LAN port on WN-AG300DGR
2. Connect power cable to WN-AG300DGR and turn it
3. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
WB2000 is a dual-band 11N AP using AR9344.
The factory firmware used the original DB120 partition table
with a small kernel partition at the end of firmware and the
kernel will easily get oversized in the future. Since it has
to be flashed using UART I also swapped kernel/rootfs and
changed the default load address.
Specification:
- SoC: Atheros AR9344
- RAM: 128 MB
- Flash: 16 MB
- Ethernet: 10/100/1000 Mbps (Atheros AR8035)
- 2x USB 2.0
- WIFI: AR9344(2G) + AR9382(5G)
- RTC: DS1338
Known issue:
5G ath9k led doesn't work due to commit ccab68f.
Flash instruction:
Set up a TFTP server on your computer and configure static IP.
Connect UART (J11 TX/GND/RX) and press any key to enter U-boot
shell.
1. Change the default boot command:
setenv bootcmd 'bootm 0x9f050000 || bootm 0x9fd50000'
saveenv
2. Set your router ipaddr and server ipaddr. e.g.:
setenv ipaddr 192.168.1.1
setenv serverip 192.168.1.50
3. Load and flash the firmware:
tftp 0x80060000 fw.bin
erase 0x9f050000 +$filesize
cp.b $fileaddr 0x9f050000 $filesize
4. Reset your router:
reset
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[Drop the i2c node unit address. Move the ath9k-leds node out of the spi
node, it doesn't belong there. Add the #gpio-cells property to the pci
wifi node. All fix dtc compiler warnings]
Signed-off-by: Mathias Kresin <dev@kresin.me>
merge
The userspace boardname derived from the dts compatible was out of sync
with the expected board added to the image metadata. This way a
sysupgrade is refused.
Sync the userspace boardname and the baordname used in the image metdata
to allow a seamless sasupgrade.
Signed-off-by: Mathias Kresin <dev@kresin.me>
qca9533 is a costdown version of qca9531 which doesn't have USB and PCIE.
Rename the misleading dtsi names and fix the SoC type of gl-ar300m.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[apply the changes for the gl-x750 as well]
Signed-off-by: Mathias Kresin <dev@kresin.me>
This commit adds support for the ROSINSON WR818 WiFi-Router
SoC: Qualcomm Atheros QCA9563,
FLASH: Winbond W25Q128FV 16MBytes,
WiFi: QCA9563 b/g/n 3x3 450Mbit/s,
USB: 1x USB 2.0 Type A, 1x USB2.0 Type C,
IN: WPS/Reset button GPIO1,
OUT: Power LED red, Internet LED red, WLAN LED red,
LAN1 LED red, LAN2 LED red, System LED red,
UART: RX-GPIO18, TX-GPIO22,
Tested and working:
- Ethernet (LAN + WAN)
- WiFi
- OpenWRT sysupgrade
- Button
- LEDs
Installation of OpenWRT from vendor firmware:
- Connect to the Web-interface at http://192.168.1.1
- Go to "Administration" -> "Firmware Upgrade"
- Upload the OpenWrt sysupgrade image
Signed-off-by: Rosy Song <rosysong@rosinson.com>
This commit modifies mtd partitions define for Buffalo BHR-4GRV2 and
move it to generic subtarget.
In Buffalo BHR-4GRV2, "kernel" partition is located behined "rootfs"
partition in the stock firmware. This causes the size of the kernel
to be limited by the fixed value.
0x50000 0xe80000 0xff0000
+-------------------------------+--------------+
| rootfs | kernel |
| (14528k) | (1472k) |
+-------------------------------+--------------+
After ar71xx was updated to Kernel 4.14, the kernel size of BHR-4GRV2
exceeded the limit, and it breaks builds on official buildbot.
Since this issue was also confirmed in ath79, I modified the mtd
partitions to get rid of that limitation.
0x50000 0xff0000
+----------------------------------------------+
| firmware |
| (16000k) |
+----------------------------------------------+
However, this commit breaks compatibility with ar71xx firmware, so I
dropped "SUPPORTED_DEVICES += bhr-4grv2".
This commit requires new flash instruction instead of the old one.
Flash instruction using initramfs image:
1. Connect the computer to the LAN port of BHR-4GRV2
2. Set the IP address of the computer to 192.168.12.10
3. Rename the OpenWrt initramfs image to
"bhr4grv2-uImage-initramfs-gzip.bin" and place it into the TFTP
directory
4. Start the tftp server on the computer
5. While holding down the "ECO" button, connect power cable to
BHR-4GRV2 and turn on it
6. Flashing (orange) diag LED and release the finger from the button,
BHR-4GRV2 downloads the intiramfs image from TFTP server and boot
with it
7. On the initramfs image, create "/etc/fw_env.config" file with
following contents
/dev/mtd1 0x0 0x10000 0x10000
8. Execute following commands to add environment variables for
u-boot
fw_setenv ipaddr 192.168.12.1
fw_setenv serverip 192.168.12.10
fw_setenv ethaddr 00:aa:bb:cc:dd:ee
fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
9. Perform sysupgrade with squashfs-sysupgrade image
10. Wait ~150 seconds to complete flashing
And this commit includes small fix; BHR-4GRV2 has QCA9557 as a SoC,
not QCA9558.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
this patch adds supports for GL-X750.
Specification:
- SOC: QCA9531 (650MHz)
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 128 MiB DDR2
- Ethernet: 10/100: 1xLAN + 10/100: 1xWAN
- Wireless: 2.4GHz (bgn) and 5GHz (ac)
- USB: 1x USB 2.0 port
- Button: 1x reset button
- LED: 5x LEDS (green)
Flash instruction:
The original firmware is openwrt, so both LuCI or sysupgrade can be used.
Signed-off-by: Luo chongjun <luochongjun@gl-inet.com>
Buffalo WZR-HP-G302H is a 2T2R 2.4 GHz 11n router, based on Atheros
AR7242.
It is Japanese market model of WZR-HP-G300NH2, but there are some
diffrences. This commit is based on WZR-HP-G300NH2 in ar71xx.
And, G302H has several hardware versions and hardware is different
dependent on the versions. This commit adds support for "A1A0"
version.
Specification:
- Atheros AR7242
- 64 MB of RAM (DDR2)
- 32 MB of Flash
- 2x 16 MB SPI-NOR flash
- 2.4 GHz 2T2R wifi
- Atheros AR9283
- 5x 10/100/1000 Mbps Ethernet
- Atheros AR8316
- 7x LEDs, 5x keys
- LED: 1x gpio-leds, 6x ath9k-leds
- key: 3x buttons, 2x slide switches
- UART header on PCB
- Vcc, GND, TX, RX from ethernet port side
- 115200n8
Flash instruction using factory image:
1. Boot WZR-HP-G302H normaly and connect the computer to its LAN port
2. Access to "http://192.168.11.1/" and move to firmware update page
("ファーム更新")
3. Select the OpenWrt factory image and click update ("更新実行")
button to perform firmware update
4. Wait ~200 seconds to complete flashing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
In order to be able to set the value of "hardware version" other than
"3", I added the "hwver" parameter.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Buffalo BHR-4GRV is a wired router, based on Atheros AR7242.
Specification:
- Atheros AR7242
- 64 MB of RAM
- 32 MB of Flash
- 2x 16 MB SPI-NOR flash
- 5x 10/100/1000 Mbps Ethernet
- 3x LEDs, 2x keys
- 1x USB 2.0 Type-A
- UART header on PCB
- JP1: Vcc, GND, TX, RX from reset button side
Flash instruction using factory image:
1. Boot the BHR-4GRV normaly and connect the computer to its LAN port
2. Access to
"http://192.168.11.1/cgi-bin/cgi?req=frm&frm=py-db/firmup.html"
with user "bufpy" and password "otdpopy"
3. Select the OpenWrt factory image and click "OK" button to perform
firmware upgrade
4. Wait ~200 seconds to complete flashing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
There are many parts that are incorrect or missing in the current
code for Buffalo WZR-HP-G450H in ath79, so its support is broken.
I fixed that issues and split to dts/dtsi files to add support for
Buffalo BHR-4GRV.
And WZR-450HP has the same hardware as WZR-HP-G450H, so I change the
device name to "WZR-HP-G450H/WZR-450HP".
Specification:
- Atheros AR7242
- 64 MB of RAM
- 32 MB of Flash
- 2x 16 MB SPI-NOR flash
- 3T3R 2.4 GHz wifi
- SoC internal
- 5x 10/100/1000 Mbps Ethernet
- 6x LEDs, 5x keys
- 1x USB 2.0 Type-A
- UART header on PCB
- JP1: Vcc, GND, TX, RX from reset button side
Flash instruction using factory image:
1. Boot the WZR-HP-G450H (or WZR-450HP) normaly and connect the computer
to its LAN port
2. Access to
"http://192.168.11.1/cgi-bin/cgi?req=frm&frm=py-db/firmup.html"
with user "bufpy" and password "otdpopy"
3. Select the OpenWrt factory image and click "OK" button to perform
firmware update
4. Wait ~200 seconds to complete flashing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
We select ath10k-ct by default, but it is still possible to build
the upstream version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John Crispin <john@phrozen.org>
Buffalo WZR-HP-AG300H is a dual band router based on
Qualcom Atheros AR7161 rev 2
Specification:
- 680 MHz CPU (Qualcomm Atheros AR7161)
- 128 MiB RAM (2x Samsung K4H511638G-LCCC)
- 32 MiB Flash (2x Winbond 25Q128BVFG)
- WiFi 5 GHz a/n (Atheros AR9220)
- WiFi 2.4 GHz b/g/n (Atheros AR9223)
- 1000Base-T WAN (Atheros AR7161)
- 4x 1000Base-T Switch (Atheros AR8316)
- 1x USB 2.0
- 3 Buttons (AOSS/WPS, Reset, USB Eject)
- 2 Slide switches (Router (on/off/auto), Movie Engine (on/off))
- 9 LEDs (Power green, WLAN 2GHz green, WLAN 2GHz amber,
WLAN 5GHz green, WLAN 5GHz LED amber, Router green,
Diag red, Movie Engine blue, USB green)
It is already supported by the ar71xx target.
For more information on the device visit the wiki:
<https://openwrt.org/toh/buffalo/wzr-hp-ag300h>
Serial console:
- The UART Header is next to Movie Engine Switch.
- Pinout is RX - TX - GND - 3.3V (Square Pad is 3.3V)
- The Serial setting is 115200-8-N-1.
Installation of OpenWRT from vendor firmware:
- Connect to the Web-interface at http://192.168.11.1
- Go to “Administration” → “Firmware Upgrade”
- Upload the OpenWrt factory image
Tested:
- Ethernet (LAN, WAN)
- WiFi
- Installation
- via TFTP rescue
- via factory image
- on firmware v1.77 (28-05-2012)
- on pro firmware v24SP2 r30356 (26-03-2018)
- via sysupgrade from ar71xx
(wlan devices don't work because of new names)
- via sysupgrade from itself
- Buttons
- LEDS
- USB (Power control and device recognition)
Signed-off-by: Bernhard Frauendienst <openwrt@nospam.obeliks.de>
ELECOM WRC-300GHBK2-I is a 2.4 GHz wireless router, based on Qualcomm
Atheros QCA9563.
Specification:
- Qualcomm Atheros QCA9563
- 64 MB of RAM (DDR2)
- 8 MB of Flash (SPI-NOR)
- 2T2R 2.4 GHz wifi
- SoC internal
- 5x 10/100/1000 Mbps Ethernet
- 3x LEDs, 4x keys(connected to GPIO: 3x)
- UART header on PCB
- TX, GND, RX, Vcc from ethernet port side
- 115200n8
Flash instruction using factory image:
1. Boot the WRC-300GHBK2-I normaly and connect the computer to its
LAN port
2. Access to "http://192.168.2.1/" and open firmware update page
("ファームウェア更新 手動更新（アップデート）")
3. Select the OpenWrt factory image and click apply ("適用") button
to perform firmware update
4. On the (initramfs) factory image, execute "mtd erase firmware" to
erase stock firmware and execute sysupgrade with squashfs-sysupgrade
image for WRC-300GHBK2-I
5. Wait ~150 seconds to complete flashing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This patch ports over support for the device from ar71xx.
SOC: AR7370 (Wasp - AR9344 rev2 0001974c)
RAM: Winbond W9725G6KB-25 32MiB
FLASH: Winbond 25Q64FVSIG 8MiB
WLAN: AR9380 Dual-Band 802.11abgn 3x3:3
INPUT: WPS, RESET button (hardware on/off toggle button)
LED: Power, LAN, WiFi, 3 RSSI-Leds (low, medium, high)
Serial: Header Next to the winbond flash chip (labeld JP1)
Pinout is GND - NC - RX - TX - 3V3 (JP1)
The Serial setting is 115200-8-N-1.
- Installation via uboot's upgrade command
0. attach serial cable
1. interrupt uboot and enter "upgrade code.bin" into
the u-boot prompt
ar7240> upgrade code.bin
2. rename openwrt...sysupgrade.bin to code.bin on PC
3. run a tftp-client on the PC
(shell)$ tftp 192.168.1.230
binary
put code.bin
4. wait for the device to finish
[...]
Copy buff to Flash from 0x9f040000 length 0x79f000
Copy to Flash... write addr: 9f040000
done
5. enter "go" in the u-boot prompt
ar7240> go
- TFTP ramdisk image boot from the uboot prompt
(tftp server defaults to serverip 192.168.1.254)
=> tftpboot 81000000 initramfs.bin
=> bootm
Tested and working:
- LEDs
- Buttons
- Ethernet
- Wi-Fi
- OpenWRT sysupgrade
For flashing and debricking information see:
<https://openwrt.org/toh/wd/rext>
Users coming from ar71xx can use sysupgrade too. But I highly
advise to no save the old configuration and start from a clean
state.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
I-O DATA ETG3-R is a wired router, based on Atheros AR9342.
Specification:
- Atheros AR9342
- 64 MB of RAM
- 8 MB of Flash
- 5x 10/100/1000 Ethernet
- AR8327N
- 2x LEDs, 1x key
- UART header on PCB
- Vcc, GND, TX, RX from ethernet port side
- 115200n8
Flash instruction using initramfs image:
1. Connect serial cable to UART header on ETG3-R
2. Rename OpenWrt initramfs image to "1500A8C0.img" and place it in
the TFTP directory
3. Set IP address of the computer to 192.168.0.10, connect to the
LAN port of ETG3-R, and start the TFTP server on the computer
4. Connect power cable to ETG3-R and turn on the router
5. Press "Enter" key when the "Hit any key to stop autoboot:" message
is displayed on the console and enter the u-boot cli
6. execute following commands to change kernel address for u-boot
setenv bootsf 1
setenv mtd_kernel1 "bootm 0x9f050000"
saveenv
7. execute "tftpboot; bootm" command to download the initramfs image from
TFTP server and boot with it
8. On the initramfs image, execute "mtd erase firmware" to erase stock
firmware and execute sysupgrade with sysupgrade image for ETG3-R
9. Wait ~150 seconds to complete flashing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
PISEN WMM003N is never supported by ar71xx, this commit also removed
SUPPORTED_DEVICES for it because it's completely useless.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This commit adds support for the AVM Fritz!Box 4020 WiFi-router.
SoC: Qualcomm Atheros QCA9561 (Dragonfly) 750MHz
RAM: Winbond W971GG6KB-25
FLASH: Macronix MX25L12835F
WiFi: QCA9561 b/g/n 3x3 450Mbit/s
USB: 1x USB 2.0
IN: WPS button, WiFi button
OUT: Power LED green, Internet LED green, WLAN LED green,
LAN LED green, INFO LED green, INFO LED red
UART: Header Next to Black metal shield
Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet (LAN + WAN)
- WiFi (correct MAC)
- Installation via EVA bootloader
- OpenWRT sysupgrade
- Buttons
- LEDs
The USB port doesn't work. Both Root Hubs are detected as having 0 Ports:
[ 3.670807] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 3.723267] usbcore: registered new interface driver usbfs
[ 3.729058] usbcore: registered new interface driver hub
[ 3.734616] usbcore: registered new device driver usb
[ 3.744181] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.758357] SCSI subsystem initialized
[ 3.766026] ehci-platform: EHCI generic platform driver
[ 3.771548] ehci-platform ehci-platform.0: EHCI Host Controller
[ 3.777708] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
[ 3.788169] ehci-platform ehci-platform.0: irq 48, io mem 0x1b000000
[ 3.816647] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 0.00
[ 3.824001] hub 1-0:1.0: USB hub found
[ 3.828219] hub 1-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 3.835825] ehci-platform ehci-platform.1: EHCI Host Controller
[ 3.842009] ehci-platform ehci-platform.1: new USB bus registered, assigned bus number 2
[ 3.852481] ehci-platform ehci-platform.1: irq 49, io mem 0x1b400000
[ 3.886631] ehci-platform ehci-platform.1: USB 2.0 started, EHCI 0.00
[ 3.894011] hub 2-0:1.0: USB hub found
[ 3.898190] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 3.908928] usbcore: registered new interface driver usb-storage
[ 3.915634] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
A few words about the shift-register:
AVM used a trick to control the shift-register for the LEDs with only 2
pins, SERCLK and MOSI. Q7S, normally used for daisy-chaining multiple
shift-registers, pulls the latch, moving the shift register-state to
the storage register. It also pulls down MR (normally pulled up) to
clear the storage register, so the latch gets released and will not be
pulled by the remaining bits in the shift-register. Shift register is
all-zero after this.
For that we need to make sure output 7 is set to high on driver probe.
We accomplish this by using gpio-hogging.
Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 169.254.157.1 (Might also be 192.168.178.1).
Firmware can be uploaded like following:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put openwrt-sysupgrade.bin mtd1
Note that this procedure might take up to two minutes. After transfer is
complete you need to powercycle the device to boot OpenWRT.
Signed-off-by: David Bauer <mail@david-bauer.net>
I-O DATA WN-AC1167DGR is a 2.4/5 GHz band 11ac router, based on
Qualcomm Atheros QCA9557.
Specification:
- Qualcomm Atheros QCA9557
- 128 MB of RAM (DDR2)
- 16 MB of Flash (SPI)
- 2T2R 2.4/5 GHz wifi
- 2.4 GHz: SoC internal
- 5 GHz: QCA988x
- 5x 10/100/1000 Mbps Ethernet
- 6x LEDs, 6x keys (4x buttons, 1x slide switch)
- UART header on PCB
- Vcc, GND, TX, RX from ethernet port side
- 115200n8
Flash instruction using factory image:
1. Connect the computer to the LAN port of WN-AC1167DGR
2. Connect power cable to WN-AC1167DGR and turn on it
3. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
If it isn't a usb led, it shouldn't be used as one by default. It is up
to the user to add such a (mis)configuration for the board.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add ath9k wifi capabilities to WNDR3700 family.
* use kmod-owl-loader to load firmware from "art"
* add wifi to DTS
* add wifi LEDs
Avoid using the same MAC for eth0 LAN and wlan0 by
toggling the eth0 MAC into a locally administered MAC.
That is currently done by in user-space by adding a
uci config item into /etc/config/network
(More elegant solution might be setting it already in
preinit phase.)
Known issues:
* wifi firmware file may not get created on the first boot
after flashing on time to bring wifi normally up. Likely
the overlay jffs2 is not yet ready for creating the
firmware file. "wifi up" may still bring wifi up.
Wifi will work normally at subsequent boots.
* phy0 and phy1 may get assigned mixed, so that phy0 may
be the 5GHz radio instead of the normal 2.4GHz, and vice
versa for phy1. Does not happen always, but may happen.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
[fix the wifi unit address in the dts]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Pisen WMM003N (sold under the name of Cloud Easy Power) is an
AR9331-based router and power bank combo device. The device uses a
stock firmware modified from OpenWRT for TP-Link TL-WR703N; however
some GPIO definition is different on this device with TL-WR703N. An
AXP202 PMIC (connected to a 5000mAh battery) and a SD slot are also
added, and the stock Flash/RAM configuration is 8MiB/64MiB.
The stock firmware is an old and heavily modified OpenWRT-based
firmware, which has telnetd defaultly open, and the root password is
"ifconfig" (quotation marks not included). The factory image format is
not known yet, however the stock firmware ships the OpenWRT's sysupgrade
command, and it can be used to install a newer firmware.
Due to the lack of the access to the STM8 embedded controller, the SD
slot is currently not usable (because it's muxed with the on-board USB
port) and the AXP PMIC cannot be monitored.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Add support for WNDR3700 and WNDR3700v2.
They share most things with WNDR3800.
Only device IDs and partition structure needs to be set.
Note: WNDR3700 (v1) has no NETGEAR_HW_ID, but has
also the NA version of the factory image.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Prepare for addition of WNDR3700 and WNDR3700v2 by
separating the common parts into wndr3700.dtsi and
leaving just the device-specific things into wndr3800.dts
The three routers are identical except
* device IDs
* WNDR3700 (v1) has only 8 MB flash, while others have 16 MB.
Partition structure needs to be defined for each device.
* (WNDR3800 has 128 MB RAM, but RAM size is not in DTS)
Also separate the common parts of the image recipe.
(Drop also the initramfs recipe.)
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
I-O DATA WN-AC1600DGR2 is a 2.4/5 GHz band 11ac router, based on
Qualcomm Atheros QCA9557.
Specification:
- Qualcomm Atheros QCA9557
- 128 MB of RAM
- 16 MB of Flash
- 2.4/5 GHz wifi
- 2.4 GHz: 2T2R (SoC internal)
- 5 GHz: 3T3R (QCA9880)
- 5x 10/100/1000 Mbps Ethernet
- 6x LEDs, 6x keys (4x buttons, 1x slide switch)
- UART header on PCB
- Vcc, GND, TX, RX from ethernet port side
- 115200n8
Flash instruction using factory image:
1. Connect the computer to the LAN port of WN-AC1600DGR2
2. Connect power cable to WN-AC1600DGR2 and turn on it
3. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This commit adds support for the OCEDO Koala
SOC: Qualcomm QCA9558 (Scorpion)
RAM: 128MB
FLASH: 16MiB
WLAN1: QCA9558 2.4 GHz 802.11bgn 3x3
WLAN2: QCA9880 5 GHz 802.11nac 3x3
INPUT: RESET button
LED: Power, LAN, WiFi 2.4, WiFi 5, SYS
Serial: Header Next to Black metal shield
Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet
- 2.4 GHz WiFi
- 5 GHz WiFi
- TFTP boot from ramdisk image
- Installation via ramdisk image
- OpenWRT sysupgrade
- Buttons
- LEDs
Installation seems to be possible only through booting an OpenWRT
ramdisk image.
Hold down the reset button while powering on the device. It will load a
ramdisk image named 'koala-uImage-initramfs-lzma.bin' from 192.168.100.8.
Note: depending on the present software, the device might also try to
pull a file called 'koala-uimage-factory'. Only the name differs, it
is still used as a ramdisk image.
Wait for the ramdisk image to boot. OpenWRT can be written to the flash
via sysupgrade or mtd.
Due to the flip-flop bootloader which we not (yet) support, you need to
set the partition the bootloader is selecting. It is possible from the
initramfs image with
> fw_setenv bootcmd run bootcmd_1
Afterwards you can reboot the device.
Signed-off-by: David Bauer <mail@david-bauer.net>
The PowerCloud Systems CR3000 was a cloud-managed CPE for a now defunct
NaaS offering. It was previously supported under the ar71xx branch and
this forward ports that support with some notable differences:
1) Since reverting to stock firmware is now irrelevant there is is only
a single openwrt image generated which uses the entire flash rather than
preserving PowerCloud-specific partitions that are unneeded to openwrt--
those partitions will be erased and used by the openwrt image.
2) Rather than use a non-standard probe order for the ethernet devices,
this image uses a set of 'ip link set ethX name ethY' commands very early
in preinit (before the network is used at all), in order to have the the
switch and Wan use the same ethernet names as in previous images.
3) /etc/config/wireless will need to be regenerated as the path to the
wireless device has changed due to differences in ath79 DT for ar93x
compared to ar71xx images.
4) eth0 is wan and eth1 is lan (switch)
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
The CAP324 was an AP for a NaaS offering that is now defunct. While
previously supported in the ar71xx arch, there were some errata (to
be fixed shortly).
Notable differences from ar71xx support:
1) The method of getting the ath9k firmware for the PCIe 2ghz wifi has
changed (due to changes in how the arch handles this), since this device
doesn't use the EEPROM except to get the MAC address of the wifi.
2) /etc/config/wireless will need to be regenerated as the path(s) to
the wireless device(s) have changed.
3) ath79 OpenWrt firmware no longer supports build an image that allows
reverting to stock firmware (as the cloud service no longer exists, the
stock firmware is useless), instead using all of the flash for image and
overlay (less u-boot/env and art).
4) Initial network config treats the ethernet port as a Lan port with
the standard default address (192.168.1.1 unless changed in .config
--e.g. via menuconfig) instead of using DHCP (this was the default for
the stock firmware, however for openwrt use this is rather confusion and
counter-productive as the user has a harder time finding the device on
the network.
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
Add ath79 arch support for PowerCloud Systems CR5000. Previously
supported under ar71xx (however there are some errors in that support;
to be fixed shortly).
Info:
* This board is based on the Atheros DB120 reference design, but doesn't
use the on-board switch. Instead it attachs GMAC0 to an AR8327 switch.
* It only uses GMAC0 and the WAN is simply a VLAN in the stock firmware.
* It has 64MB RAM and 8MB flash.
* In the dts version we get rid of using 'open-drain' for the AR8327
LED controls.
* As with the platform data version we disable JTAG as this conflicts
with one of the pair of GPIO's required for the power/status LED
(GPIO2 and GPIO4 are used for this LED).
* The pcie card wifi has an EEPROM but gets it's MAC address from
the ART partition.
* The SoC wifi (2.4 GHz) is all from the ART.
* The USB is support comes from the SoC.
NB. This is actually an AR9342 rather than AR9344 but we use the 9344
definitions because there are no relevant differences for this board.
NB: Building only images that don't support reverting to the old
cloud-based firmware as the Skydog cloud service for the CR5000 no
longer exists.
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
This commit adds support for the OCEDO Raccoon
SOC: Atheros AR9344
RAM: 128MB
FLASH: 16MiB
WLAN1: AR9344 2.4 GHz 802.11bgn 2x2
WLAN2: AR9382 5 GHz 802.11an 2x2
INPUT: RESET button
LED: Power, LAN, WiFi 2.4, WiFi 5
Serial: Header Next to Black metal shield
Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V)
The Serial setting is 115200-8-N-1.
NOTE: The U-Boot won't boot with the serial attached.
Boot the device without serial attached and attach it
after 3 seconds.
Tested and working:
- Ethernet
- 2.4 GHz WiFi
- 5 GHz WiFi
- TFTP boot from ramdisk image
- Installation via ramdisk image
- OpenWRT sysupgrade
- Buttons
- LEDs
Installation seems to be possible only through booting an OpenWRT
ramdisk image.
Hold down the reset button while powering on the device. It will load a
ramdisk image named 'raccoon-uImage-initramfs-lzma.bin' from 192.168.100.8.
Note: depending on the present software, the device might also try to
pull a file called 'raccoon-uimage-factory'. Only the name differs, it
is still used as a ramdisk image.
Wait for the ramdisk image to boot. OpenWRT can be written to the flash
via sysupgrade or mtd.
Due to the flip-flop bootloader which we not (yet) support, you need to
set the partition the bootloader is selecting. It is possible from the
initramfs image with
> fw_setenv bootcmd run bootcmd_1
Afterwards you can reboot the device.
Signed-off-by: David Bauer <mail@david-bauer.net>
This patch adds dts for qca956x and also support for Phicomm K2T
The qca965x.dtsi adds nearly all the necessary components.
Both ath9k AHB and PCIe worked well.
The Phicomm K2T uses MTD partition 'config' to store the mac addresses in
JSON format. To extract these fields correctly, a script is introduced:
/lib/functions/k2t.sh
This script provides a helper function to extract mac addresses, and is used
in three places.
Hardware spec of Phicomm K2T:
CPU: QCA9563
DRAM: 64MB DDR2
Flash: 16MB SPI-NOR
Switch: QCA8337
WiFi 5.8GHz: QCA9886
Flash instruction:
Apply sysupgrade.bin via serial console:
tftp 0x80000000 sysupgrade.bin && erase 0x9f090000 +$filesize && cp.b $fileaddr 0x9f090000 $filesize
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Based on original ar71xx eg200 board files
Tested working:
* usb hub, storage and serial port
* ethernet
* wifi
* leds
* button
sysupgrade from self->self passes validity checks.
sysupgrade from old ar71xx->ath79 passes. (however this doesn't migrate
wireless driver configs)
Only unknown issue is the existance of a /sys/class/leds/ath9k-phy0,
which doesn't "exist"
Signed-off-by: Karl Palsson <karlp@etactica.com>
Remove recipes for not yet migrated boards. Drop variables which aren't
required due to the switch to devicetree like boardname.
Drop the legacy image build code. Boards added to this target shouldn't
use the legacy image build code anyway.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add the SoC compatible to the individual dts files. Rename the dts files
to match the common pattern.
Remove dts files wich aren't used and no image in ar71xx exists.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This target aims to replace ar71xx mid-term. The big part that is still
missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik
subtargets will follow.
Signed-off-by: John Crispin <john@phrozen.org>
