This issue was reported by @paper42, who is using Void Linux with musl
to compile OpenWrt and its packages and found out it is not possible to
compile U-boot for Turris Omnia (neither any other).
It fixes following output:
```
HOSTCC tools/kwboot
tools/kwboot.c: In function 'kwboot_tty_change_baudrate':
tools/kwboot.c:662:6: error: 'struct termios' has no member named 'c_ospeed'
662 | tio.c_ospeed = tio.c_ispeed = baudrate;
| ^
tools/kwboot.c:662:21: error: 'struct termios' has no member named 'c_ispeed'
662 | tio.c_ospeed = tio.c_ispeed = baudrate;
| ^
tools/kwboot.c:690:31: error: 'struct termios' has no member named 'c_ospeed'
690 | if (!_is_within_tolerance(tio.c_ospeed, baudrate, 3))
| ^
tools/kwboot.c:693:31: error: 'struct termios' has no member named 'c_ispeed'
693 | if (!_is_within_tolerance(tio.c_ispeed, baudrate, 3))
|
```
Tested-by: Michal Vasilek <michal.vasilek@nic.cz>
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
(cherry picked from commit 9c7472950b)
At some point after 21.02.3 and before 22.03.0, the size limits of the
Linksys RE6500 were reached and prevent booting from the 22.03.0 release
or builds of current SNAPSHOT. This patch allows builds of master to boot
again and has been tested on my device.
Fixes: #8577
Signed-off-by: Mark King <mark@vemek.co>
(cherry picked from commit bf5b1a53d4)
For some reason, Microsoft's Plan9 driver returns IOError on missing
file.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
(cherry picked from commit 875e17774b)
When building with an external toolcahin with musl also include
./include/fortify by default. This is also done when we build with the
internal toolchain using musl libc.
Without this extra include the fortify source feature is not working
when using an external musl toolchain. All binaries were compiled
without fortify source when an external musl toolchain was used. All
binaries release done by the OpenWrt project use the internal toolcahin
where fortify source is working.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit b21ddbfa18)
When we use the internal toolchain USE_SSTRIP will be selected by
default for musl libc and USE_STRIP when glibc is used. Do the same when
an external toolchain is used. USE_GLIBC will also be set for external
toolchain builds based on the EXTERNAL_TOOLCHAIN_LIBC_USE_GLIBC setting.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 9403810c02)
Openwrt now supports only glibc and musl. Add support for musl and
rework the libc check to handle the new config flags and correctly
compile package basend on that.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 7be01fe13b)
Openwrt generate info.mk that contains the libc type. For probe_cc check
if the file exist and parse directly it for LIBC type.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 75311977f5)
Currently we never call probe_cc before config generation, this cause
the script to never actually detect the correct libc type.
Call probe_cc before config generation to correctl set the .config file.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit ddeabc75eb)
It can be useful to overwrite an already generated config.
Option are simply added at the end of the config and make defconfig
will overwrite the relevant option with the new one.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit f4dd18ca39)
The parsed prefix in print_config is wrong and this produce broken
generated .config that won't work with any external toolchain.
Currently the prefix from a CC of
'arm-openwrt-linux-muslgnueabi-gcc-12.1.0'
produce a prefix
'arm-openwrt-linux-muslgnueabi-gcc-'
This is wrong as the real prefix should be
'arm-openwrt-linux-muslgnueabi-'
This is probably caused by a change in how the toolchain is now handled
that now append also the gcc version. Probably in ancient days the
version wasn't part of the name and the prefix generation stripped the
'-gcc' instead of the gcc version.
Fix this and correctly strip the gcc version and the gcc suffix to
correctly call toolchain bins.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 53c293262f)
Don't add wrapped bin to the TARGET_PATH as it does cause compilation
error.
cmake.mk will use the "command -v" and will use the wrapped bin instead
of the external toolchain bin as they have the same name and command
will select the first result.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit a90eabf602)
When using the OpenWrt toolchain as an external toolchain the build
failed due to missing LTO support. By choosing the GCC wrappers of
the tools this commit makes sure that the LTO-enabled executables
are being used.
Signed-off-by: Vincent Wiemann <vincent.wiemann@ironai.com>
[ wrap the commit description to 72 char ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 2555ffb453)
Watchdog and poe_passthrough gpios require the jtag disabled.
Signed-off-by: Santiago Piccinini <spiccinini@altermundi.net>
(cherry picked from commit 2ad949b11d)
Fixes build warnings when using newer versions of grep.
Signed-off-by: Chris Osgood <chris_github@functionalfuture.com>
Tested-by: Georgi Valkov <gvalkov@gmail.com>
(cherry picked from commit c5e167e0d6)
[ fix conflict error ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
We simply grep for "/usr". So no need for "-E" or "\/". Furthermore, in
the new grep versions this creates warnings.
As written in the grep-3.8 announcement:
Regular expressions with stray backslashes now cause warnings, as
their unspecified behavior can lead to unexpected results.
For example, '\a' and 'a' are not always equivalent
<https://bugs.gnu.org/39678>.
Fixes warnings in the form of:
grep: warning: stray \ before /
Signed-off-by: Nick Hainke <vincent@systemli.org>
(cherry picked from commit a29d3bc48c)
[ fix conflict error ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
- fix including modules.mk when a target is being replaced
- fix calling make targets from target/linux
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 3a8825ad6a)
Fixes: ebc36ebb23 ("scripts/feeds: install targets to target/linux/feeds and support overriding")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 00094efec3)
Backports Linux kernel patch [1] for kernel 5.10 where it applies cleanly.
This was tested on CZ.NIC Turris 1.1 router running OpenWrt 22.03
release.
Before:
- In /var/log/messages:
```
[ 16.392988] lm90 0-004c: cannot request IRQ 48
[ 16.398280] lm90: probe of 0-004c failed with error -22
```
- Sensors does not work:
```
root@turris:~# sensors
No sensors found!
Make sure you loaded all the kernel drivers you need.
Try sensors-detect to find out which these are.
```
After:
```
root@turris:/# sensors
sa56004-i2c-0-4c
Adapter: MPC adapter (i2c@3000)
temp1: +44.0°C (low = +0.0°C, high = +70.0°C)
(crit = +85.0°C, hyst = +75.0°C)
temp2: +73.8°C (low = +0.0°C, high = +70.0°C) ALARM (HIGH)
(crit = +85.0°C, hyst = +75.0°C)
```
[1] https://lore.kernel.org/linux-gpio/20220906105431.30911-1-pali@kernel.org/
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
(cherry picked from commit 2f496c34b6)
(c&p commit ID from openwrt's master)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This change was included in the original pull request but later omitted
for some reason:
https://github.com/openwrt/openwrt/pull/4936
Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
(cherry picked from commit 4cccea02a6)
Enabling KERNEL_KPROBES exposes KERNEL_BPF_KPROBE_OVERRIDE. Add a build
option for it to fix build failures with KERNEL_KPROBES enabled.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry picked from commit 500c37c56f)
Broadcom's U-Boot contains environment data blocks. They need to be
found (offsets aren't predefined) to access env variables.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 137149847d)
When the v1 and v2 variants of the U6LR were introduced, the board
network config was not adapted to the new device names. Due to this, the
wrong network config is applied during initial boot. The resulting
config has lan, wan and a switch, while this device only has a single
ethernet interface without a switch.
Fix this by using a wildcard that matches all the variants.
Fixes: 15a02471bb ("mediatek: new target mt7622-ubnt-unifi-6-lr-v1")
Fixes: 5c8d3893a7 ("mediatek: new target ubnt_unifi-6-lr-v1-ubootmod")
Fixes: 31d86a1a11 ("mediatek: add Ubiquiti UniFi 6 LR v2 targets")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 117f41ee95)
Serge Vasilugin reports:
To improve mt7620 built-in wifi performance some changes:
1. Correct BW20/BW40 switching (see comments with mark (1))
2. Correct TX_SW_CFG1 MAC reg from v3 of vendor driver see
https://gitlab.com/dm38/padavan-ng/-/blob/master/trunk/proprietary/rt_wifi/rtpci/3.0.X.X/mt76x2/chips/rt6352.c#L531
3. Set bbp66 for all chains.
4. US_CYC_CNT init based on Programming guide, default value was 33 (pci),
set chipset bus clock with fallback to cpu clock/3.
5. Don't overwrite default values for mt7620.
6. Correct some typos.
7. Add support for external LNA:
a) RF and BBP regs never be corrected for this mode
b) eLNA is driven the same way as ePA with mt7620's pin PA
but vendor driver explicitly pin PA to gpio mode (for forrect calibration?)
so I'm not sure that request for pa_pin in dts-file will be enough
First 5 changes (really 2) improve performance for boards w/o eLNA/ePA.
Changes 7 add support for eLNA
Configuration w/o eLAN/ePA and with eLNA show results
tx/rx (from router point of view) for each stream:
35-40/30-35 Mbps for HT20
65-70/60-65 Mbps for HT40
Yes. Max results for 2T2R client is 140-145/135-140
with peaks 160/150, It correspond to mediatek driver results.
Boards with ePA untested.
Reported-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[directly include v3 of the patchset submitted upstream]
(cherry picked from commit 31a6605de0)
(cherry picked from commit e785ca05e9)
(cherry picked from commit 412fcf3d44)
Prepare patches for sending upstream by adding patch descriptions
generated from the original OpenWrt commits adding each patch.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit d4feb66048)
The RGB LED of the UniFi 6 LR v1 doesn't work when using the Openwrt-
built U-Boot. This is because the vendor loader resets the ledbar
controller while our U-Boot doesn't care.
Add reset-gpio so the ledbar driver in Linux will always reset the
ledbar controller.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 0b5cf952cf)
Hardware
--------
- SoC: MediaTek MT7621AT with 128 MiB RAM and 32 MiB Flash
- Wi-Fi: MediaTek MT7603 (b/g/n, 2x2) and MediaTek MT7615 (ac, 4x4)
- Bluetooth: CSR8811 (internal USB, install kmod-bluetooth)
Installation
------------
1. Connect to the booted device at 192.168.1.20 using username/password
"ubnt".
2. Update the bootloader environment.
$ fw_setenv devmode TRUE
$ fw_setenv boot_openwrt "fdt addr \$(fdtcontroladdr);
fdt rm /signature; bootubnt"
$ fw_setenv bootcmd "run boot_openwrt"
3. Transfer the OpenWrt sysupgrade image to the device using SCP.
4. Check the mtd partition number for bs / kernel0 / kernel1
$ cat /proc/mtd
5. Set the bootselect flag to boot from kernel0
$ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock4
6. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1
$ dd if=openwrt.bin of=/dev/mtdblock6
$ dd if=openwrt.bin of=/dev/mtdblock7
7. Reboot the device. It should boot into OpenWrt.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
(cherry picked from commit 820f0c07c5)
The patch adding support for LEDs connected to a reset controller did
not apply any more, refresh it on top of current master.
Fixes: 53fc987b25 ("generic: move ledbar driver from mediatek target")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 76fc277917)
This moves the ledbar driver to generic, to be also used by the ramips target.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
(cherry picked from commit 53fc987b25)
The LEDs connected to the MCU are so-called smart LEDs and their signal is
daisy-chained. Because of this, the MCU needs to be told how many LEDs are
connected. It also means the LEDs could be individually controlled, if the MCU
has a command for this.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
(cherry picked from commit 76198e8f09)
During GPIO initialization the pin state flips and triggers a reset of
the ledbar MCU. It needs to be moved through an initialization sequence
before working correctly.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
(cherry picked from commit 013a956f08)
Some versions of the ledbar MCU have a reset pin. It needs to be
correctly initialized or we might keep the MCU in reset state.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
(cherry picked from commit 84e4bbf5f0)
There are commands that return more than one byte of response.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
(cherry picked from commit 7c852e7df5)
Or the comparison against a signed char is always true, because the
literal 0xaa is treated as an unsigned int, to which the signed char is
casted during comparison. 0xaa is above the positive values of a signed
char and negative signed char values result in values larger than 0xaa
when casted to unsigned int.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
(cherry picked from commit e9a22ce253)
The read response is in the i2c_response variable. Also use %hhx format,
because we're dealing with a single char.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
(cherry picked from commit c4f9f9b44c)
Package kernel module providing ESSIV support for block encryption.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 4133102898)
Janusz Dziedzic reported a typo introduced by a recent commit. Fix it.
Fixes: 50c892d67b ("mediatek: bpi-r64: make initramfs/recovery optional")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 007c8809c1)
Only include recovery image in SD card image generated for the
BananaPi BPi-R64 if building with CONFIG_TARGET_ROOTFS_INITRAMFS
This allows to build images larger than 32 MB (the limit for
initramfs/recovery image) by deselecting initramfs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 50c892d67b)
Add the missing LEDs for GB-PC2. Some of these LEDs don't exist on the
device schematics. Tests on a GB-PC2 by me and Petr proved otherwise.
Remove ethblack-green and ethblue-green LEDs for GB-PC1. They are not wired
to GPIO 3 or 4 and the wiring is currently unknown.
Set ethyellow-orange to display link state and activity of the ethyellow
interface for GB-PC2.
Link: https://github.com/ngiger/GnuBee_Docs/blob/master/GB-PCx/Documents/GB-PC2_V1.1_schematic.pdf
Tested-by: Petr Louda <petr.louda@outlook.cz>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
(cherry picked from commit 2a6ef7f53d)
