Older MT7623 ARMv7 SoC as well as new Filogic platforms come with
inside-secure,safexcel-eip97 units. Enable them in DTS and select the
driver kernel module by default on those platforms.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Initially this covers MT7986 only, but it will later be expanded to cover other
Filogic branded platforms by MediaTek
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
It will be supported by the new filogic subtarget
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
All targets expect the malta target already activate the CONFIG_GPIOLIB
option. Move it to generic kernel configuration and also activate it for
malta.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
CONFIG_INPUT_MISC does not do any changes to the kernel image, it only
shows some extra kernel configuration options.
Activate it on all targets.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
On boot, kernel log complains no vbus supply is found:
`xhci-mtk 1a0c0000.usb: supply vbus not found, using dummy regulator`
so add the dts node entries to solve the issue
Signed-off-by: Andrew Sim <andrewsimz@gmail.com>
When building the mediatek/mt7629 target in OpenWrt 22.03 the kernel
does not have a configuration option for CONFIG_CRYPTO_DEV_MEDIATEK. Add
this option to the generic kernel configuration and also add two other
configuration options which are removed when we refresh the mt7629
kernel configuration.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The recent differentiation between v1 and v2 of the UniFi 6 LR added
support for the v2 version which has GPIO-controlled LEDs instead of
using an additional microcontroller to drive an RGB led.
The polarity of the white LED, however, was inverted and the default
states didn't make a lot of sense after all. Fix that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fix the wps button to prevent wrongly detected recovery procedures.
In the official banana pi r64 git the wps button is set to
GPIO_ACTIVE_LOW and not GPIO_ACTIVE_HIGH.
Import patch to fix on boot unwanted recovery entering:
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
- failsafe button wps was pressed -
- failsafe -
Signed-off-by: Nick Hainke <vincent@systemli.org>
This is now built-in, enable so it won't propagate on target configs.
Link: https://lkml.org/lkml/2022/1/3/168
Fixes: 79e7a2552e ("kernel: bump 5.15 to 5.15.44")
Fixes: 0ca9367069 ("kernel: bump 5.10 to 5.10.119")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
(Link to Kernel's commit taht made it built-in,
CRYPTO_LIB_BLAKE2S[_ARM|_X86] as it's selectable, 5.10 backport)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
There is not RTC battery connected to the SoC of the UniFi 6 LR board.
Disable the RTC to prevent the system coming up with time set to
2000-01-01 00:00:00 after each reboot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add targets:
* Ubiquiti UniFi 6 LR v2
* Ubiquiti UniFi 6 LR v2 (U-Boot mod)
This target does not have a RGB led bar like v1 did
Used target/linux/ramips/dts/mt7621_ubnt_unifi.dtsi as inspiration
The white dome LED is default-on, blue will turn on when the system is
in running state
Signed-off-by: Henrik Riomar <henrik.riomar@gmail.com>
based on current ubnt_unifi-6-lr-ubootmod
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[added SUPPORTED_DEVICES for compatibility with existing setups]
Signed-off-by: Henrik Riomar <henrik.riomar@gmail.com>
Based on current mt7622-ubnt-unifi-6-lr, this is a preparation for
adding a v2 version of this target
* v1 - with led-bar
* v2 - two simple GPIO connected LEDs (in later commits)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[added SUPPORTED_DEVICES for compatibility with existing setups]
Signed-off-by: Henrik Riomar <henrik.riomar@gmail.com>
Remove redundant target-level entries, noting that these settings will be
configured from "Kernel build options" of Kconfig.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[remove from new configs introduced after patch submission]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The config for LEDS_UBNT_LEDBAR doesn't stay in mt7629 kconfig because
of its I2C dependency. Build it as a module and let buildroot handle
this config option instead.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Disable support for joysticks, micee and tablets. There's no actual
driver selected in kconfig, and including kernel support is just a
waste of space. Besides that, I believe nobody wants these on a router.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Remove patches and configuration for Linux 5.10 which have been left
in the tree despite the target having been switched to Linux 5.15.
Fixes: c283defa88 ("mediatek: switch to 5.15")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Set CONFIG_SCHED_MC in config-5.15 to have make the scheduler aware
of shared caches.
Reported-by: Rui Salvaterra <rsalvaterra@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Last attempt on this has a typo and doen't work.
It seems that this is a common problem occurring on every kernel bump,
so let's enforce arch timer support for mt7623 with a patch instead.
Fixes: 9a22943eb2 ("mediatek: 5.15: re-enable arch timer on MT7623 as well")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
the SPI-NAND driver switch breaks dts compatibility. It's too much work
to backport all ECC framework support to 5.10 so let's switch the target
to 5.15 instead.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This patch implements the spi-nand controller driver as an ECC-capable
spi-mem controller to use the upstream SPI-NAND driver.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
the OOB layout in MTK SNFI uses the 2nd byte, and anything using OOB
will make the block a bad-block in spi-nand driver.
Hack it for now. We need a proper solution upstream.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Adresses of device tree nodes are typically noted without the '0x'
prefix. While having the '0x' prefix doesn't hurt when using Linux,
more recent versions of U-Boot will add a duplicate ramoops node as a
simple string compare is used to check if the node is already present.
Remove the '0x' prefix to avoid the kernel warning resulting from
U-Boot adding a dupplicate pstore/ramoops node.
See also https://lists.denx.de/pipermail/u-boot/2022-April/481810.html
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The MediaTek's Crypto Engine module is only available for mt7623, in
which case it is built into the kernel.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>