Add a common definition of Fortinet FortiGate devices to
image/cortexa9.mk for a preparation of adding support for
other FortiGate 3xE/5xE devices.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Hardware:
SoC: Qualcomm Atheros QCA956X ver 1 rev 0
CPU clock: 775.000 MHz
Memory: 128 MB DDR2
Flash: 32 MB SPI NOR mx25l25635e
Switch: Atheros AR8327 rev. 4
Ethernet: 5x 10/100/1000 Mbps (1 WAN + 4 LAN)
Buttons: 1x Reset
Serial: TX, RX, GND, VCC
Baudrate: 115200
Wifi: Qualcomm Atheros qca988x 802.11ac/n - 3x3
Qualcomm Atheros AR9561 802.11b/g/n - 3x3
Not working:
Leds: 1x via a SPI controller
Display: ST7789V or ILI9341V
controlled by stm32f205.
Note:
DSA changes are ready, but we have an issue with
ports not working after 20-30 minutes. So for now
we use swconfig.
Installation: serial connection only
There is a J11 four pin connector. You need to connect TX, RX and GND.
You can find very good information about the device here
https://github.com/alexanderhenne/AFi-R?tab=readme-ov-file#finding-j11
Upgrading via serial port:
1. Download the kernel initramfs image. Copy the image to a TFTP server
2. Connect to console on the AP, and connect the LAN1 port to your PC LAN
3. Stop autoboot to get to U-boot shell
Interrupt the autoboot process by pressing any key when prompted
4. Transfer the kernel image with TFTP
Set your ip address on your TFTP server to 192.168.1.254
# tftpboot 0x81000000 amplifi-router-hd-initramfs-kernel.bin
5. Load the image
# bootm 0x81000000
6. SCP sysupgrade image from your PC to the Amplifi HD
(If you use a newer mac use scp -O)
# scp openwrt-ath79-generic-ubnt_amplifi-router-hd-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
7. Write sysupgrade to the firmware partition
# mtd write /tmp/openwrt-ath79-generic-ubnt_amplifi-router-hd-squashfs-sysupgrade.bin firmware
8. Reboot your device
# reboot
Credit to alexanderhenne for all the information.
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
ELECOM WRC-X1800GS is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based on
MT7621A.
Specification:
- SoC : MediaTek MT7621A
- RAM : DDR3 256 MiB
- Flash : RAW-NAND 128 MiB (Macronix MX30LF1G28AD-TI)
- WLAN : 2.4/5 GHz 2T2R (MediaTek MT7915D)
- Ethernet : 5x 10/100/1000 Mbps
- switch : MediaTek MT7530 (SoC)
- LEDs/Keys (GPIO) : 7x/4x
- UART : pin-header on PCB ("J5")
- arrangement : 3.3V, TX, RX, NC, GND from tri-angle marking
- settings : 115200n8
- Power : 12 VDC, 1 A
Flash instruction using initramfs-factory image:
1. Boot WRC-X1800GS normally with "Router" mode
2. Access to "http://192.168.2.1/" and open firmware update page
("ファームウェア更新")
3. Select the OpenWrt initramfs-factory image and click apply ("適用")
button
4. After flashing initramfs-factory image and reboot, upload the
sysupgrade image and perform sysupgrade with it
5. Wait ~120 seconds to complete flashing
Notes:
- WRC-X1800GS has 2x os images. Those are switched on every firmware
updating on stock firmware, but dual-boot feature on this device
cannot be handled on OpenWrt. So the 1st image is always used on
OpenWrt.
This is controlled by "bootnum" variable embedded in "persist"
partition (addr: 0x4).
- WRC-X1800GS has 2x HW revisions. There are some small changes, but the
same DeviceTree in stock firmware is used for both revisions.
On this support of WRC-X1800GS, 2x green:wlan-2g-N LEDs are defined
for each revision and the same default triggers are set.
MAC addresses:
LAN : 38:97:A4:xx:xx:38 (Factory, 0x1fdfa (hex) / Ubootenv, ethaddr (text))
WAN : 38:97:A4:xx:xx:3B (Factory, 0x1fdf4 (hex))
2.4 GHz: 38:97:A4:xx:xx:39
5 GHz : 38:97:A4:xx:xx:3A
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Add support for ELECOM WRC-X1800GS on uboot-envtools, to update
bootmenu_delay variable on sysupgrade.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Prior e8725a932e, version used to be
VERSION:=$(PKG_VERSION)-$(PKG_RELEASE)
After e8725a932e, the version is:
VERSION:=$(PKG_VERSION)-r$(PKG_RELEASE)
Hence the gen_*_cyclonedxsbom functions need to be updated to remove
the trailing -r prefix in the version in order to generate correct
version info in the SBOM.
Signed-off-by: Akshay Bhat <nodeax@gmail.com>
The EnGenius EAP1300 and EAP1300EXT use identical boards and firmware
(as flashed) from the vendor.
As with the EAP1300, the EAP1300EXT requires a specific firmware version
to flash OpenWRT. Unfortunately, the required firmware is truncated on
the vendor's website.
A working file can be created as follows:
```
curl \
https://www.engeniustech.com/wp_firmware/eap1300-all-v3.5.3.5_c1.9.04.bin \
| perl -pe 's/\x09EAP1300_A/\x0cEAP1300EXT_A/' \
> eap1300ext-all-v3.5.3.5_c1.9.04.bin
```
The file should have sha256:
`58a1197a426139a12b03fd432334e677124cbe3384349bd7337f2ee71f1dcfd4`.
Please see commit 2b4ac79 for further
details.
The vendor firmware must be decrypted before it can be flashed from
OpenWRT. A tool able to do that is available from:
https://github.com/ryancdotorg/enfringement/blob/main/decrypt.py
Signed-off-by: Ryan Castellucci <code@ryanc.org>
The vendor U-Boot on the Cudy M3000 and the Yuncore AX835 assign random
mac addresses on boot and set the 'local-mac-address' property which
prevents Openwrt from assigning the correct address from evmem.
This patch removes the alias for ethernet0 so that U-Boot doesn't add the
property, removes the workaround from 02_network, and adds back the nvmem
definition for the M3000.
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
OpenWrt supported the D-Link DSM G600 A in the past. It has
64 MB of RAM and 16 MB of flash so it will run just fine,
and should be quite usable with a rootfs on an external
harddrive.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
OpenWrt supported the Freecom FSG-3 in the past. It has
64 MB of RAM so will run fine, but the bare 4 MB of flash
makes it a non-default target. The generated compressed
image is currently below 4MB (just 3.3 MB) though, so it
should be possible to flash just fine with a rootfs on
a harddrive or USB stick, which is what the FSG-3 used
in the past as well.
The device has a WAN port on eth0 and three LAN ports on
eth1. The LAN ports are probably a DSA switch but the
old OpenWrt base never activated that, instead it relies
on boot defaults.
Due to questionable usablity without tweaking and further
work this image is not built by default, but made available
for developers who know what they are doing.
The TAR+CRC image generation is a rewritten version of the
earlier support code.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
OpenWrt supported the Iomega NAS100D in the past and it has
64 MB of RAM so if booted from a harddrive it will probably
work just fine. The APEX boot loader already has a build
variant for this machine that we can just pick up and use.
This device has a single ethernet port so bring this online
with DHCP as expected for a NAS device.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Several of the IXP4xx machines mount root on external harddrives
so add EXT4 and rootfs-part to the featureset so the right
features are always selected.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Common specifications:
* Mediatek MT7988A (4x Cortex-A73, up to 1.8 GHz clock speed)
* 8 GiB eMMC
* 2 GiB DDR4 RAM
* 1x 10000M/1000M/100M + 3x 1000M/100M/10M LAN ports
* MT7996 Tri-band (2.4G, 5G, 6G) 4T4R 802.11be Wi-Fi
* Airoha AG3352 GPS
* Renesas DA14531MOD Bluetooth
* 2 buttons (Reset, Mesh/WPS)
* uC-controlled RGB LED via I2C
* 2x LED for each 1G port, 3x LED for each 10G port
* USB 3.0 type A port
* 3.3V-level 115200 baud UART console via 4-pin Dupont connector
exposed at the bottom of the device
* USB-C PD power input
SDG-8733: 1x 10000M/1000M/100M WAN port
SDG-8734: 1x USXGMII/10GBase-R/5GBase-R/2500Base-X/1000Base-X/SGMII SFP+
Both models are also available in versions including 2x FXS POTS interfaces
for analog phones. Those interfaces are not supported by OpenWrt.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add missing call to emmc_copy_config which either writes the sysupgrade
tar.gz backup file or clears the existing rootfs_data overlay.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport patch adding support for the AQR114C PHY and add support for
PHY LEDs and polarity setting of Aquantia 3rd and 4th generation PHYs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Carambola3 is a WiFi module based on Qualcomm/Atheros QCA4531
http://wiki.8devices.com/carambola3
Specification:
- 650/600/216 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 32 MB of FLASH
- 2T2R 2.4 GHz
- 2x 10/100 Mbps Ethernet
- 1x USB 2.0 Host socket
- UART for serial console
- 12x GPIO
Flash instructions:
Upgrading from ar71xx target:
- Upload image into the board:
scp openwrt-ath79-generic-8dev_carambola3-squashfs-sysupgrade.bin \
root@192.168.1.1/tmp/
- Run sysupgrade
sysupgrade -F /tmp/openwrt-ath79-generic-8dev_carambola3-squashfs-sysupgrade.bin
Upgrading from u-boot:
- Set up tftp server with openwrt-ath79-generic-8dev_carambola3-initramfs-kernel.bin
- Go to u-boot (reboot and press ESC when prompted)
- Set TFTP server IP
setenv serverip 192.168.1.254
- Set device ip from the same subnet
setenv ipaddr 192.168.1.1
- Copy new firmware to board
tftpboot 0x82000000 initramfs.bin
- Boot OpenWRT
bootm 0x82000000
- Upload image openwrt-ath79-generic-8dev_carambola3-squashfs-sysupgrade.bin into the board
- Run sysupgrade.
Signed-off-by: Andrey Bondar <a.bondar@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/15514
Signed-off-by: Robert Marko <robimarko@gmail.com>
Basic changes to make linux-atm build without any issues with GCC 14.
Besides some errors caused by -Wpointer-sign, there was also an issue
with socklen_t not being used for getsockopt() and accept()
sometimes.
I also updated the Debian patch to include the latest changes from
version "1:2.5.1-5.1" in Debian Sid. This allowed me to drop
"600-fix-format-errors.patch" and "700-include_sockios.patch".
Signed-off-by: Rany Hany <rany_hany@riseup.net>
This 4G/LTE modem is a WiFi hotspot, and also works as cdc_ether modem
when plugged over USB. It needs usb-modeswitching. With HuaweiNewMode,
it will modeswitch from 3426:1f01 (mass-storage) to 3426:14db
(cdc_ether).
Signed-off-by: Didier 'OdyX' Raboud <odyx@raksha.ch>
Link: https://github.com/openwrt/openwrt/pull/15497
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
CPU: MT7628AN 580MHz
RAM: 64MB DDR2
FLASH: 8MB EN25QH64 NOR SPI
WIFI: 2.4GHz 2x2 MT7628 b/g/n internal
WIFI: 5GHz 1x1 MT7610E ac/n PCI
LTE: Qualcomm MDM9207
ETH: 4xLAN 100base-T integrated
SWITCH: RT3050-ESW Port 0,1,2,3: LAN, Port 6: CPU
LEDS: LAN, WAN, Power, 3x signal strength, WiFi
BTNS: Reset, WiFi toggle
UART: Near ETH ports, Vcc-GND-RX-TX, 115200, 8N1
Installation:
1. Update using recovery mode
- set your IP to 192.168.0.225, subnet mask: 255.255.255.0
- start tftp server, rename tftp-recovery.bin to
tp_recovery.bin and place it into the server's directory
- while holdig the "reset" button, power on the device
- keep holding "reset" until the file is being transferred
Notes:
This board has only one MAC address programmed
in the "romfile" partition:
- MAC for phy0 (2.4GHz) at romfile 0xf100 (0)
- MAC for phy1 (5GHz) at romfile 0xf100 (-1)
- stock firmware re-uses phy0 MAC for ethernet
- stock firmware uses romfile 0xf100 (1) for WWAN;
not used since QMI interface is raw IP
Signed-off-by: Lea Teuberth <lea.teuberth@outlook.com>
mt7915e driver supports MT7915 & MT7916 devices and MT7981 & MT7986
on-SoC wireless controllers. Devices based on MT7988 and possibly other
next chipsets are quite unlikely to need it (MT7988 was designed to be
used with MT7996).
Move kmod-mt7915e to DEVICE_PACKAGES of relevant devices.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Refresh all tools patches now that tools/refresh correctly works.
CI now checks for them and actively complain if tools have unrefreshed
patches.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[ reword commit message ]
Link: https://github.com/openwrt/openwrt/pull/15524
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
meson is used to build it since 291b137. No need to patch Makefiles.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15524
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Other than OPKG which only uses signed package list, APK uses
individually signed packages in addition to signed package lists. Hence,
in order to be able to generate package, the private key needs to be
generated before compiling packages. Express that dependency and
generate the private key before building any packages instead of doing
so as part of the base-files package build.
Fixes: d788ab376f ("build: add APK package build capabilities")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Currently, in case that PSGMII calibration fails it will panic the kernel
which is not ideal and is preventing any debugging to be done.
So, since PGMII calibration failing only means that wired networking wont
work lets convet the panic() call to dev_error.
Link: https://github.com/openwrt/openwrt/pull/15542
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds support for Netgear Orbi Pro SXR80 and SXS80 (collectively known as SXK80)
Specifications:
---------------
* CPU: Qualcomm IPQ8074A Quad core Cortex-A53
* RAM: 1024MB
* Storage: SPI-NAND 512 MiB (Winbond W29N04GZ)
* Ethernet: 4x 1G RJ45 ports (QCA8075) 1x 2.5G RJ45 LAN/WAN (QCA8081)
* WLAN:
- 2.4 GHz: Qualcomm QCN5024 4x4
- 2x 5 GHz: Qualcomm QCN5054 4x4 (second radio high channels only)
* LEDs:
- Power: (Green and red)
- Front: (Blue, green, red and white)
* Buttons:
- 1x Soft reset
- 1x Sync/WPS
* Power: 12V DC Jack
Installation instructions (Telnet):
-----------------------------------
*Note, this guide assumes SXR80, for SXS80 change the firmware file name as appropriate
1. Put firmware file openwrt-qualcommax-ipq807x-netgear_sxr80-initramfs-uImage.itb in root of TFTP server available at 192.168.1.10.
2. Enable telnet by going to http://[ip of device]/debug.htm and clicking on the tickbox 'Enable telnet'
3. Telnet into the device and login using the same username and password as the web interface:
4. Run the following command:
`fw_setenv bootcmd 'env default -a; saveenv; reset'`
5. Reboot the router, once the web interface is available again re-enable telnet via http://[ip of device]/debug.htm and telnet into the device.
6. Run the following command:
`fw_printenv`
It should look similar to the below:
```
baudrate=115200
bootargs=console=ttyMSM0,115200n8
bootcmd=mii write 0x0 0x0 0x800; sleep 1; nmrp; bootdni; boot_DNI_secureboot
bootdelay=2
ipaddr=192.168.1.1
netmask=255.255.255.0
serverip=192.168.1.10
soc_version_major=2
soc_version_minor=0
```
**If you see the message:**
`Warning: Bad CRC, using default environment`
**DO NOT CONTINUE, YOU WILL BRICK YOUR DEVICE**
7. Run the following command:
`fw_setenv originalboot 'mii write 0x0 0x0 0x800; sleep 1; nmrp; bootdni; boot_DNI_secureboot'`
(This should match what's in the bootcmd variable displayed in step 6)
8. Run the following commands:
```
fw_setenv wrttftp 'mii write 0x0 0x0 0x800; sleep 1; nmrp; if tftpboot openwrt-qualcommax-ipq807x-netgear_sxr80-initramfs-uImage.itb; then bootm; fi; bootdni; boot_DNI_secureboot'
fw_setenv wrtboot 'mii write 0x0 0x0 0x800; sleep 1; nmrp; nand read 0x40000000 0x1980000 0x06d00000; bootm 0x40000000'
fw_setenv bootcmd 'run wrttftp'
```
9. Ensure SXR/S device is attached via ethernet (LAN port) to the same ethernet segment as the TFTP server.
10. Reboot the device, it should reboot into OpenWrt and be available on 192.168.1.1
11. Once OpenWrt has booted, update the bootcmd using the following command:
`fw_setenv bootcmd 'run wrtboot'`
12. Flash the sysupgrade image
13. It should boot into OpenWrt
References to SXK80 GPL source:
https://www.downloads.netgear.com/files/GPL/SXK80-V3.2.0.108_gpl_src.tar.bz2.zip
Signed-off-by: Flole Systems <flole@flole.de>
Signed-off-by: Andrew Smith <gul.code@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/14939
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that Host/Prepare/Default is always defined, we can use that instead
of using raw commands to move files from the src directory to
HOST_BUILD_DIR.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Install files from HOST_BUILD_DIR instead of src. These files are now
correctly copied to HOST_BUILD_DIR and can be referenced from there.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
We currently skip defining Host/Prepare/Default if HOST_UNPACK is not
defined.
This is mostly the case for Host packages that just provide files with
the src directory and don't need to be downloaded/extracted.
This was probably done lots of times ago due to quilt causing error as
the patches directory wasn't present.
This has changed now and quilt can correctly detect if no patches needs
to be applied (instead of terminating with error)
Always define Host/Prepare/Default to make tools/refresh correctly works
as HOST_QUILT is hardcoded enabled for this make target and will
complain for tool not prepared for quilt patches.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix revision calculation when local branch is rebased on new "main" branch
instead of "master".
Signed-off-by: Marius Dinu <m95d+git@psihoexpert.ro>
Link: https://github.com/openwrt/openwrt/pull/15538
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
It seems that on Spectrum SAX1V1K QCA8081 is being brought out of reset
too quickly and thus causing it to get stuck in an invalid autoneg
register configuration mode.
Setting an deasset delay seems to fix this, so lets set it.
Fixes: #15493
Link: https://github.com/openwrt/openwrt/pull/15541
Signed-off-by: Robert Marko <robimarko@gmail.com>
During the last update to 12.5.r2 printing of the attached PHY-s was
removed, so lets bring it back as it is very helpfull for debugging
OpenWrt issues without users having to modify NSS-DP to know if a PHY
was attached.
Refresh patches since nss_dp_main.c was edited.
Link: https://github.com/openwrt/openwrt/pull/15537
Signed-off-by: Robert Marko <robimarko@gmail.com>
filogic: Add support for D-Link AQUILA PRO AI M30
Specification:
- MT7981 CPU using 2.4GHz and 5GHz WiFi (both AX)
- 1GB RAM
- 16MB NOR
- 128MB NAND
- 3 LEDs (red, green, blue, white)
- 2 buttons (reset, user defined)
- 1 2.5Gbit WAN port (Airoha EN8811h)
- 1 1Gbit LAN ports
- 1 single lane M.2 SSD slot
- 1 mikroBus socket
- externel HW WDT (25s refresh time)
- i2c RTC (with battery backup)
Serial Interface
- UBS-C CDC-ACM
- 3 Pins GND, RX, TX
- Settings: 115200, 8N1
MAC addresses are not populated on the early samples.
Signed-off-by: John Crispin <john@phrozen.org>
The IXP4xx is well supported upstream and can readily be
supported with kernel v6.6. To simplify things after the
DTS directory was renamed, switch to v6.6 only.
Bring in some outstanding patches.
Tested on the Gateworks GW2348-4.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since we set the root for APK it tries to use those during the build,
which shouldn't happen since local package are used instead.
Disable the repositories by manually setting an empty repository.
Signed-off-by: Paul Spooren <mail@aparcar.org>
These patches have partial acceptance upstream and are still
a WIP, now there is merge window for kernel v6.10 so these
will not be reposted until that is over. In the meantime,
let's add the current state to OpenWrt so the ethernet on
Gemini is up and working (tested on several devices).
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
