Add ethernet0 alias in device tree to make U-Boot inherit the Ethernet
mac address (set via environment variable 'ethaddr') down to Linux.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Each of
- CRYPTO_AEAD2
- CRYPTO_AEAD
- CRYPTO_GF128MUL
- CRYPTO_GHASH
- CRYPTO_HASH2
- CRYPTO_HASH
- CRYPTO_MANAGER2
- CRYPTO_MANAGER
- CRYPTO_NULL2
either directly required for mac80211 crypto support, or directly
selected by such options. Support for the mac80211 crypto was enabled in
the generic config since c7182123b9 ("kernel: make cryptoapi support
needed by mac80211 built-in"). So move the above options from the target
configs to the generic config to make it clear why do we need them.
CC: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Both CLANG_VERSION and LLD_VERISON are autogenerated runtime
configuration options, so add them to the kernel configuration filter
and remove from generic and per-target configs to keep configs clean.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
BMT replaces nand-specific ops for erasing and writing, but the
mtk-snand driver only implements generic mtd api.
Replace erase, block_isbad, block_markbad in mtd_info for generic mtd
drivers.
Fixes: b600aee3ed ("mediatek: attach bmt to the new snand driver")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
There's no such thing as ucidef_set_interfaces_lan. It's
ucidef_set_interface_lan.
Cc: David Bauer <mail@david-bauer.net>
Signed-off-by: Mark Mentovai <mark@moxienet.com>
Similar to mt7623, also no longer use 'blockdev' and stop relying on
in-kernel partition parsers. Instead, strip off all metadata using
'fwtool' while writing the firmware image and scrape the number of
blocks written from 'dd', then use that block offset to stash the
configuration backup.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Re-reading the partition table doesn't work reliably, it fails if
anything on the device is still in use and it's not trivial to prevent
every possible case of a block device still being in use somehow.
Therefore, instead of relying on the in-kernel partition parser to know
where to write the configuration backup, use OpenWrt's format-agnostic
fwtool to strip off all metadata from the image and count its blocks
while writing. In that way we can know where to write the config backup
without needing the kernel to parse the MBR and FIT structures.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use find_mmc_part instead of previously introduced
get_partition_by_name which requires a custom kernel patch.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use find_mmc_part instead of previously introduced
get_partition_by_name which requires a custom kernel patch.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Deleted (upstreamed):
bcm27xx/patches-5.10/950-0145-xhci-add-quirk-for-host-controllers-that-don-t-updat.patch [1]
Manually rebased:
bcm27xx/patches-5.10/950-0355-xhci-quirks-add-link-TRB-quirk-for-VL805.patch
bcm53xx/patches-5.10/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
Note: although automatically rebaseable, the last patch has been edited to avoid
conflicting bit definitions.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-5.10.y&id=b6f32897af190d4716412e156ee0abcc16e4f1e5
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
In case of the block device still being in use, re-reading the
partition table fails. In that case, abort sysupgrade to avoid
corrupting the just-written image because of wrong offsets caused
by failure to re-read the partition table.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Enable kernel options to allow loading device tree overlay via configfs
at runtime. This is useful for devboards like the BPi-R2 and BPi-R64
which got RasbPi-compatible 40-pin GPIO header which allow all sorts
of extensions.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
All subtargets only provide files and patches for Linux 5.10 by now
so there is little use for the old Linux 5.4 stuff. Remove it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add common features 'gpio', 'nand', 'pci', 'pcie', 'squashfs' and 'usb'
for all mediatek targets, add 'display' and 'usbgadget' for MT7623.
Sort features alphabetically while at it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
User reported that R64 doesn't provide power to the mPCIe slot in case
the PCIe port is disabled as it is when selecting the SATA
configuration. As users may still want to use USB-connected mPCIe
modules in CN8 slot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The default value for CONFIG_RCU_CPU_STALL_TIMEOUT was changed from 60
seconds to 21 seconds in 2012 in the upstream kernel. Some targets
already use 21 seconds.
This patch changes the default value in the generic configuration to 21
seconds and removes the target specific configuration options.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Rui Salvaterra <rsalvaterra@gmail.com>
Specifications:
- SoC: MT7622
- RAM: 512MB
- Flash: MX35LF1GE4AB 128MB SPI NAND
- Ethernet: RTL8367S 5x1GbE
- WiFi: 2.4G: MT7622 5G: MT7615N x2
- Other ports: USB3.0 x1
Flash instruction:
*important*: upgrade vendor firmware to at least V7.1cu.643_B20200521
1. hold the reset button and power on the device. wait for about 10s
before releasing the reset button.
2. upload sysupgrade.bin via u-boot recovery page on http://192.168.1.1
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
CONFIG_RCU_{NEED_SEGCBLIST,STALL_COMMON} are set basically everywhere. Move them
to the generic kconfigs. And resort the generic kconfigs while at it.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Based on the existing documentation [1][2], I dare anyone to demonstrate that
we need to fine-tune these RCU parameters. The (performance) breakage potential
for doing so is immense, so let's just please put down this loaded footgun.
Disable CONFIG_RCU_EXPERT and its dependent symbols. Additionally, remove the
CONFIG_RCU_EXPERT symbol from the target kconfigs which contain it.
[1] https://www.kernel.org/doc/Documentation/RCU/Design/Data-Structures/Data-Structures.html
[2] https://lwn.net/Articles/777214/
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
These options doesn't show up unless some kernel packages are selected,
so they are not covered by kernel_menuconfig.
Manually add them so that a build with all kmods can pass without user
interaction.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
there's no driver level remapping of oob data in the new spi-nand
driver and bmt oob signature starts at 0x0 of the dumped oob data.
change the default value to 0 for the new spi-nand driver.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
mtd->size will be overrided by BMT which makes all mtd requests made by
bmt fail in request size checking.
this commit changes the driver to check against actual chip size in chip
info as a workaround.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
we now have a standalone mtd driver and the old spi-mem driver along
with the hack in spi-nand core can be removed.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This patch enables new spi-nand driver for mt7622 and mt7629.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This patch adds a new spi-nand driver which implements the SNFI of mt7622
and mt7629.
Unlike the existing snfi driver which makes use of the spi-mem framework
and the spi-nand framework with modified ecc support, this driver is
implemented directly on the mtd framework with other components untouched,
and provides better performance, and behaves exactly the same as the nand
framework.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Built clock drivers for G3DSYS and AUDSYS into the kernel to allow
multimedia features (GPU and audio) to work if they exist.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport support for dual-role USB 2.0 as that's what is actually
built-into MT7623.
Improve HDMI console by enabling VT and setting up tty1..tty6.
Re-add accidentally removed CONFIG_ARM_ARCH_TIMER.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
In order to make HDMI console available on the BananaPi BPi-R2 select
various Kconfig symbols which are useful for systems with graphics.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
kirkwood build broke due to missing include needed for ETH_ALEN.
Add patch (sent upstream as well) to address that.
Refresh patches for 5.4 and 5.10.
Fixes: 91a52f22a1 ("treewide: backport support for nvmem on non platform devices")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
MT7622 provides are hardware RNG with upstream Linux driver. Enable
compilation of this driver to make use of the hardware RNG.
Signed-off-by: David Bauer <mail@david-bauer.net>
The 1st generation MediaTek PCIe host bridge cannot handle Message
Signaled Interrupts (MSIs). The core PCI code is not aware that MSI is
not available. This results in warnings of the form:
WARNING: CPU: 2 PID: 112 at include/linux/msi.h:219
pci_msi_setup_msi_irqs.constprop.8+0x64/0x6c
Modules linked in: ahci(+) libahci libata sd_mod scsi_mod
gpio_button_hotplug
CPU: 2 PID: 112 Comm: kmodloader Not tainted 5.10.52 #0
Hardware name: Mediatek Cortex-A7 (Device Tree)
Import patches that introduce the 'no_msi' attribute to signal missing
MSI support to the core PCI.
Refresh patches:
- 000-spi-fix-fifo.patch
- 330-mtk-bmt-support.patch
- 510-net-mediatek-add-flow-offload-for-mt7623.patch
- 601-PCI-mediatek-Use-regmap-to-get-shared-pcie-cfg-base.patch
- 610-pcie-mediatek-fix-clearing-interrupt-status.patch
- 700-net-ethernet-mtk_eth_soc-add-support-for-coherent-DM.patch
- 710-pci-pcie-mediatek-add-support-for-coherent-DMA.patch
Signed-off-by: Nick Hainke <vincent@systemli.org>
This patch did not apply cleanly any more after support for the XTX
flash was added to the generic patches.
Fixes: 92012dd867 ("kernel: Add support for XTX XT26G02A SPI NAND")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The patch fixes the fifo rx mode for the mt7623. It is already accepted
upstream for Linux Kernel 5.15.
To test the spi we can change the dts file to
&spi0 {
pinctrl-names = "default";
pinctrl-0 = <&spi0_pins_a>;
status = "okay";
spidev: spidev@0 {
compatible = "linux,spidev";
spi-max-frequency = <1000000>;
reg = <0>;
};
};
Afterwards we should see a spidev device under /dev/.
To test it we can further use spidev-test.
Signed-off-by: Nick Hainke <vincent@systemli.org>
The image generation code for the U7623 board expects ext4 filesystem
to be selected in menuconfig and CONFIG_TARGET_ROOTFS_PARTSIZE to be
defined. Now that ext4 isn't enabled any more, the variable was missing
and broke the build.
Set the default (104) instead of using the config variable to fix that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
When reworking the BPi-R2 the mtk-mmc-img build step was removed
despite it was still needed to build the image for the UniElec U7623
board. Add it back for now until U7623 gets its facelift.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
A full read-write rootfs cannot work inside uImage.FIT as the hash
will obviously change once writing to it. Disable generating ext4
rootfs images.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* introduce recovery (=initramfs) vs. production dual boot scheme
* make use of uImage.FIT (instead of FAT partition)
* generate images using build steps (instead of external scripts)
* simplify sysupgrade and config restore (thanks to uImage.FIT)
* make sure mmc devices are ordered persistently (set DT aliases)
This commit breaks sysupgrade from existing installations, you will
have to re-install using the sdcard.img.gz image.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware flow offloading was reported to work when setting the right
version identifier. Import a patch from Frank Wunderlich doing that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Update Kernel config and set Linux 5.10 for mediatek/mt7623.
(patches have already been updated to 5.10 when mt7622 was bumped)
Tested on Bananapi BPi-R2.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Define nvmem-cells and convert mtd-mac-address to nvmem implementation.
The conversion is done with an automated script.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Manually rebased:
bcm27xx/patches-5.4/950-0089-cgroup-Disable-cgroup-memory-by-default.patch
All other patches automatically rebased.
Signed-off-by: John Audia <graysky@archlinux.us>
This updates the patches to match the versions included in the mtd
subsystem for the next Linux kernel version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In order to allow easily updating the bootloader on eMMC also provide
artifacts for that. Support for updating bootloader via TFTP will be
added to the loader CLI menu in a follow-up commit.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
It is possible to select CONFIG_MTD_PARSER_TRX on the mediatek now. Add
this option to the kernel configuration file.
Fixes: 58c5e25664 ("mediatek: support non standard trx magic values")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Generating the sdcard.img.gz file requires the initramfs/recovery
image to be present. Use the newly introduced 'append-image-stage'
build command to fix the ImageBuilder for the BPi-R64.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Build the driver for the in-SoC AHCI SATA host as module, just like for
the other subtargets. No board requires booting off SATA, so we don't
need to have it built-in. All boards with SATA support already select
kmod-ata-ahci-mtk which provides the module.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Some targets select HZ=100, others HZ=250. There's no reason to select a higher
timer frequency (and 100 Hz are available in every architecture), so change all
targets to 100 Hz.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
For the targets which enable ubifs, these symbols are already part of the
generic kconfigs. Drop them from the target kconfigs.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Ran update_kernel.sh in a fresh clone without any existing toolchains.
Removed upstreamed:
mvebu/patches-5.4/319-ARM-dts-turris-omnia-configure-LED-2--INTn-pin-as-interrupt-pin.patch
Build system : x86_64
Build-tested : ipq806x/R7800
Run-tested : ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
When adding Kernel 5.10 support, the kernel configuration did not
include the LED driver required for the UniFi 6 LR. Also the actual
driver source went missing.
Fixes commit c46ccb69d1 ("mediatek: mt7622: add Linux 5.10 support")
Signed-off-by: David Bauer <mail@david-bauer.net>
Some of bpi-r64 boards have serial NAND attached to SPI bus.
Add SD card image support for installing openwrt to it.
Default to nand upgrade if root device is not mmc block device.
Separate preloader and uboot images for snand are generated.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
/dts-v1/; must only be specified once.
Fixes: e887049fbb ("mediatek: add alternative bootchain variant
for UniFi 6 LR")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Builds images for the Ubiquiti Network UniFi 6 LR device running the
U-Boot build added by the previous commits.
Everything but MTD partitions is moved to dtsi.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Ran update_kernel.sh in a fresh clone without any existing toolchains.
Manually rebased:
pending-5.4/611-netfilter_match_bypass_default_table.patch
The upstream change affecting this patch is the revert of an earlier
kernel commit. Therefore, we just revert our corresponding changes
in [1].
Build system: x86_64
Build-tested: ipq806x/R7800
[1] 9b1b89229f ("kernel: bump 5.4 to 5.4.86")
Signed-off-by: John Audia <graysky@archlinux.us>
[adjust manually rebased patch, add explanation]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
1. Use upstream accepted NVMEM patches
2. Minor fix for BCM4908 partitioning
3. Support for Linksys firmware partitions on Northstar
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Populate the recovery and production partitions of the generated sdcard
image for the Bananapi BPi-R64.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Ran update_kernel.sh in a fresh clone without any existing toolchains.
Manually rebased:
bcm27xx/950-0993-xhci-quirks-add-link-TRB-quirk-for-VL805.patch
layerscape/701-net-0231-enetc-Use-DT-protocol-information-to-set-up-the-port.patch
Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
[remove accidental whitespace edit]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
There is an ASMedia ASM1480 PCIe switch found on mt7622-rfb1 and the
BPi-R64, allowing the user to switch between SATA and PCIe1 which share
the same pins on the SoC.
This chip is not present on the Linksys E8450, it doesn't have SATA.
Remove definitions for GPIO90 from DTSI to prevent it from being
copy&pasted or otherwise causing confusion.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Ubiquiti's own bootloader expects the configuration mode to be present
with a "@" instead of a "-" for the sperator character. Otherwise
booting of the image fails.
Signed-off-by: David Bauer <mail@david-bauer.net>
This fixes writing to the U-Boot environment by making the partition
writable and setting the correct flash sector size of 128K.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Bananapi BPi-R64 got a SATA interface which cannot be used at the
same time as the second mPCIe slot. The decission is made by hogging
GPIO 90.
Embed two addtional DT overlay blobs into the image to allow bootloader
selection of either SATA or PCIE1 feature.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
kmod-mt7615e kmod-mt7615-firmware and uboot-envtools are already part
of the target's default package set. No need to add them again for
buffalo_wsr-2533dhp2.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This adds support for the Buffalo WSR-2533DHP2.
The device uses the Broadcom TRX image format with a special magic. To
be able to boot the images or load them they have to be wrapped with
different headers depending how it is loaded.
There are multiple ways to install OpenWrt on this device.
Boot ramdisk from U-Boot
----------------------------
This will load the image and not write it into the flash.
1. Stop boot menu with "space" key
2. Select "System Load Linux to SDRAM via TFTP."
3. Load this image:
openwrt-mediatek-mt7622-buffalo_wsr-2533dhp2-initramfs-kernel.bin
4. The system boots the image
Write to flash from U-Boot
-----------------------------
This will load the image over tftp and directly write it into the flash.
1. Stop boot menu with "space" key
2. Select "System Load Linux Kernel then write to Flash via TFTP."
3. Load this image:
openwrt-mediatek-mt7622-buffalo_wsr-2533dhp2-squashfs-factory-uboot.bin
4. The system writes this image into the flash and boots into it.
Write to flash from Web UI
-----------------------------
This will load the image over over the Web UI and write it into the flash
1. Open the Web UI
2. Go to "管理" -> "ファームウェア更新"
3. Select "ローカルファイル指定" and click "更新実行"
4. Load this image:
openwrt-mediatek-mt7622-buffalo_wsr-2533dhp2-squashfs-factory.bin
5. The system writes this image into the flash and boots into it.
Specifications
-------------------
* SoC: MT7622 (4x4 2.4 GHz Wifi)
* Wifi: MT7615 (4x4 5 GHz Wifi)
* Flash: Winbond W29N01HZ 128MB SLC NAND
* RAM 256MB
* Ethernet: Realtek RTL8367S (5 x 1GBit/s, SoC via 2.5GBit/s)
Co-Developed-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Buffalo uses the TRX format with a different magic, add support for
this.
It is planned to send these patches upstream.
Cc: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This fixes some bugs in the mtk parallel nand driver introduced in 5.10.
This patch was send upstream.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* clean up whitespace to make GPT partitioning more readable
* don't select packages already part of the target default selection
* don't select U-Boot variants (breaks ImageBuilder)
* don't select AHCI on boards without SATA
* don't select kmod-usb2 and kmod-ohci, USB 1.x and USB 2.0 devices
work fine with the in-SoC XHCI host having just kmod-usb3 installed.
* select kmod-btmtkuart for devices with Bluetooth support
* sort DEVICE_PACKAGES
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
dd on Mac OS X apparently fails when using 'M' unit for bs.
dd: bs: illegal numeric value
Use 'k' unit instead for 'pad-to' to fix that.
Reported-by: Georgi Valkov <gvalkov@abv.bg>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This was added recently and thus overlooked in 85b1f4d8ca
("treewide: remove execute bit and shebang from board.d files").
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The in-SoC RTC of the Bananapi R64 is more disruptive than useful
without a battery connected. Disable it to not have Linux use the
RTC provided time 2000-01-01 00:00:00 after power-loss.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
So far, board.d files were having execute bit set and contained a
shebang. However, they are just sourced in board_detect, with an
apparantly unnecessary check for execute permission beforehand.
Replace this check by one for existance and make the board.d files
"normal" files, as would be expected in /etc anyway.
Note:
This removes an apparantly unused '#!/bin/sh /etc/rc.common' in
target/linux/bcm47xx/base-files/etc/board.d/01_network
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Also add a new kconfig symbol (CONFIG_KCMP) to the generic config,
disabling the SYS_kcmp syscall (it was split from
CONFIG_CHECKPOINT_RESTORE, which is disabled by default, so the
previous behaviour is kept).
Removed (upstreamed) patches:
070-net-icmp-pass-zeroed-opts-from-icmp-v6-_ndo_send-bef.patch
081-wireguard-device-do-not-generate-ICMP-for-non-IP-pac.patch
082-wireguard-queueing-get-rid-of-per-peer-ring-buffers.patch
083-wireguard-kconfig-use-arm-chacha-even-with-no-neon.patch
830-v5.12-0002-usb-serial-option-update-interface-mapping-for-ZTE-P685M.patch
Manually rebased patches:
313-helios4-dts-status-led-alias.patch
104-powerpc-mpc85xx-change-P2020RDB-dts-file-for-OpenWRT.patch
Run tested:
ath79 (TL-WDR3600)
mvebu (Turris Omnia)
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
5.4.102 backported a lot of stuff that our WireGuard backport already
did, in addition to other patches we had, so those patches were
removed from that part of the series. In the process other patches were
refreshed or reworked to account for upstream changes.
This commit involved `update_kernel.sh -v -u 5.4`.
Cc: John Audia <graysky@archlinux.us>
Cc: David Bauer <mail@david-bauer.net>
Cc: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
All mt7622 devices except for the UBI-variant of the mt7622-rfb1 carry
metadata appended to the sysupgrade image.
Add it for the mt7622-rfb1-ubi as well and check it on sysupgrade to
avoid accidentally flashing firmware for the wrong device (or variant
or future DEVICE_COMPAT_VERSION).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
mt7622 uses MBR partition for booting from SD card.
Add hybrid MBR entry with boot flag after PMBR entry.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
The previous approach of referencing artifacts in follow-up artifacts
can't work with parallel builds in the current way image.mk is built.
Refactor things so this is not needed.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Write everything needed for eMMC install into the gaps between
partitions on SD card. In that way, installation to eMMC only needs
the SD card, no additional files need to be loaded via TFTP any more.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This profile is meant to be used on MT7622 rfb1 AP, indicate that in
the name to make things less confusing.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
These patches are required for the Ubiquiti UniFi 6 LR to work. They
were already present for kernel 5.4 but got lost when adding 5.10
support.
Signed-off-by: David Bauer <mail@david-bauer.net>
**What's new**
* Bring support for the Bananapi BPi-R64 to the level desirable for
a nice hackable routerboard.
* Use ARM Trusted Firmware A from source. (goodbye binary preloader)
* Use Das U-Boot from source. (see previous commit)
* Assemble SD-card image using OpenWrt image-commands.
(no gen_sd_cruz_foo.sh added, this is not Raspbian)
* Updated kernel options to support root filesystem.
* Updated DTS to match OpenWrt LAN ports, known LEDs, buttons, ...
* Detect root device, handle sysupgrade, config restore, ...
* Wire up (known) LEDs and buttons in OpenWrt-fashion.
* Build one set of images from SD-card and eMMC.
* Hopefully provide a good example of how things can be done right
from scratch.
**Installation and images**
* Have an empty SD-card at hand
* Write stuff to the card, as root (card device is /dev/mmcblkX)
- write header, gpt, bl2, atf, u-boot and recovery kernel:
`cat *bpi-r64-boot-sdcard.img *bpi-r64-initramfs-recovery.fit > /dev/mmcblkX`
- rescan partitions:
`blockdev --rereadpt /dev/mmcblkX`
- write main system to production partition:
`cat *bpi-r64-squashfs-sysupgrade.fit > /dev/mmcblkXp5`
* Installation to eMMC works using SD-card bootloader via TFTP
When running OpenWrt of SD-card, issue this to trigger installation
to eMMC:
`fw_setenv bootcmd run emmc_init`
Be prepared to serve the content of bin/targets/mediatek/mt7622 on
TFTP server address 192.168.1.254.
**What's missing**
* The red LED is always on, probably a hardware bug.
* AHCI (probably needs DTS changes)
* Ship SD-card image ready with every needed for eMMC install.
* The eMMC has a second, currently unused boot partition. This would
be ideal to store the WiFi EEPROM and Ethernet MAC address(es).
@sinovoip ideas?
Thanks to Thomas Hühn @thuehn for providing the hardware!
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The vendor flash layout of the Linksys E8450 is problematic as it uses
the SPI-NAND chip without any wear-leveling while at the same time
wasting a lot of space for padding.
Use an all-UBI layout instead, storing the kernel+dtb+squashfs in
uImage.FIT standard format in UBI volume 'fit', the read-write
overlay in UBI volume 'rootfs_data' as well as reduntant U-Boot
environments 'ubootenv' and 'ubootenv2', and a 'recovery'
kernel+dtb+initramfs uImage.FIT for dual-boot.
** WARNING **
THIS PROCEDURE CAN EASILY BRICK YOUR DEVICE PERMANENTLY IF NOT CARRIED
OUT VERY CAREFULLY AND EXACTLY AS DESCRIBED!
Step 0
* Configure your PC to have the static IPv4 address 192.168.1.254/24
* Provide bin/targets/mediatek/mt7622 via TFTP
Now continue EITHER with step 1A or 1B, depending on your preference
(and on having serial console wired up or not).
Step 1A (Using the vendor web interface (or non-UBI OpenWrt install))
In order to update to the new bootloader and UBI-based firmware,
use the web browser of your choice to open the routers web-interface
accessible on http://192.168.1.1
* Navigate to
'Configuration' -> 'Administration' -> 'Firmware Upgrade'
* Upload the file
openwrt-mediatek-mt7622-linksys_e8450-ubi-initramfs-recovery.itb
and proceed with the upgrade.
* Once OpenWrt comes up, use SCP to upload the new bootloader files to
/tmp on the router:
*-mt7622-linksys_e8450-ubi-preloader.bin
*-mt7622-linksys_e8450-ubi-bl31-uboot.fip
* Connect via SSH as you will now need to replace the bootloader in
the Flash.
ssh root@192.168.1.1
(the usual warnings)
* First of all, backup all the flash now:
for mtd in /dev/mtdblock*; do
dd if=$mtd of=/tmp/$(basename $mtd);
done
* Then use SCP to copy /tmp/mtdblock* from the router and keep them
safe. You will need them should you ever want to return to the
factory firmware!
* Now flow the uploaded files:
mtd -e /dev/mtd0 write /tmp/*linksys_e8450-ubi-preloader.bin /dev/mtd0
mtd -e /dev/mtd1 write /tmp/*linksys_e8450-ubi-bl31-uboot.fip /dev/mtd1
If and only if both writes look like the completed successfully
reboot the router. Now continue with step 2.
Step 1B (Using the vendor bootloader serial console)
* Use the serial to backup all /dev/mtd* devices before using the
stock firmware (you got root shell when connected to serial).
* Then reboot and select 'U-Boot Console' in the boot menu.
* Copy the following lines, one by one:
tftpboot 0x40080000 openwrt-mediatek-mt7622-linksys_e8450-ubi-preloader.bin
tftpboot 0x40100000 openwrt-mediatek-mt7622-linksys_e8450-ubi-bl31-uboot.fip
nand erase 0x0 0x180000
nand write 0x40080000 0x0 0x180000
reset
Now continue with step 2
Step 2
Once the new bootchain comes up, the loader will initialize UBI and the
ubootenv volumes. It will then of course fail to find any bootable
volume and hence resort to load kernel via TFTP from server
192.168.1.254 while giving itself the address 192.168.1.1
The requested file is called
openwrt-mediatek-mt7622-linksys_e8450-ubi-initramfs-recovery.itb
and your TFTP server should provide exactly that :)
It will be written to UBI as recovery image and booted.
You can then continue and flash the production OS image, either
by using sysupgrade in the booted initramfs recovery OS, or by using
the bootloader menu and TFTP.
That's it. Go ahead and mess around with a bootchain built almost
completely from source (only DRAM calibration blobs are fitted in bl2,
and the irreplacable on-chip ROM loader remains, of course).
And enjoy U-Boot built with many great features out-of-the-box.
You can access the bootloader environment from within OpenWrt using the
'fw_printenv' and 'fw_setenv' commands. Don't be afraid, once you got
the new bootchain installed the device should be fairly unbrickable
(holding reset button before and during power-on resets things and
allows reflashing recovery image via TFTP)
Special thanks to @dvn0 (Devan Carpenter) for providing amazingly fast
infra for test-builds, allowing for `make clean ; make -j$(nproc)` in
less than two minutes :)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The Linksys E8450, also known as Belkin RT3200, is a dual-band
IEEE 802.11bgn/ac/ax router based on MediaTek MT7622BV and
MediaTek MT7915AN chips.
FCC: K7S-03571 and K7S-03572
Hardware highlights:
- CPU: MediaTek MT7622BV (2x ARM Cortex-A53 @ 1350 MHz max.)
- RAM: 512MB DDR3
- Flash: 128MB SPI-NAND (2k+64)
- Ethernet: MT7531BE switch with 5 1000Base-T ports
CPU port connected with 2500Base-X
- WiFi 2.4 GHz: 802.11bgn 4T4R built-in antennas
MT7622VB built-in
- WiFi 5 GHz: 802.11ac/ax 4T4R built-in antennas
MT7915AN chip on-board via PCIe
MT7975AN front-end
- Buttons: Reset and WPS
- LEDS: 3 user controllable LEDs, 4 wired to switch
- USB: USB2.0, single port
- no Bluetooth (supported by SoC, not wired on board)
- Serial: JST PH 2.0MM 6 Pin connector inside device
----_____________----
[ GND RX - TX - - ]
---------------------
- JTAG: unpopulated ARM JTAG 20-pin connector (works)
This commit adds support for the device in a way that is compatible
with the vendor firmware's bootloader and dual-boot flash layout, the
resulting image can directly be flashed using the vendor firmware.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Switch mt7622 subtarget to Linux 5.10, it has been tested by many of us
on several devices for a couple of weeks already.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MediaTek targets always use U-Boot's modern uImage.FIT format which
allows bundling several blobs into a single file including hashes,
descriptions and more. In fact, we are already using that to bundle
the Flattened Device Tree blob with the kernel on this and many
other targets.
In the same fashion, we can now make use of the newly introduced
support for building seperate ramdisk to uImage.FIT with a dedicated
initrd blob checked and loaded by U-Boot instead of embedding the
cpio archive into the kernel itself.
This allows for having larger ramdisks, choosing ramdisk compression
independently of kernel compression (while only kernel is decompressed
by the bootloader) and for more easily replacing or modifying the
filesystem contained in an initramfs image.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Ran update_kernel.sh in a fresh clone without any existing toolchains.
Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
[refresh again]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
simplify maintaining mt7622-bananapi-bpi-r64-rootdisk.dts by
storing only differences between upstream dts
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
The SPDX license identifier must be in the first line of a file,
unless there is a shebang (then it's the second line).
Fix this for the local files, do not care about the upstream patches.
While at it, update the identifiers where necessary.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Instead of adding those device tree sources using a patch, simply move
them to the newly created dts folder.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use approach suggested by Adrian Schmutzler instead of introducing
another device variable.
Also revert the unnecessary white-space changes accidentally introduced
by the previous commit.
Fixed: c067b1e79b ("mediatek: move out-of-tree DTS files to dedicated dts folder")
Suggested-by: Adrian Schmutzler <mail@adrianschmutzler.de>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use dedicated dts folder like on ramips to store device tree source
files for boards not already supported in vanilla Linux.
Doing so instead of having them in files-* has several advantages:
* we don't need to duplicate them for several kernel versions
* changes to a device tree don't trigger a complete kernel rebuild
* the files are more obvious to find
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware
--------
MediaTek MT7622
512MB DDR3 RAM
64M SPI-NOR Flash (Winbond W25Q512JV)
MediaTek MT7622 802.11bgn 4T4R WMAC
MediaTek MT7915 802.11ax 4T4R
Marvell AQR1112 100/1000/2500 NBase-T PHY
Holtek HT32F52241 LED controller
Reset Switch
UART
----
CPU UART0 at the pinout next to the Holtek MCU.
Pinout (first pin next to SoC / MCU)
0 3V3
1 RX
2 TX
3 GND
Settings are 115200 8N1.
Opening the case
----------------
Opening the case is not a nice task, as itis glued together. Insert a
flat knife between the front and back casing below the ethernet port.
Open up a gap this way and insert a flat scredriver, remove the knife.
Work your way around the casing by applying force to seperate the front
and back casing. This losens the glue and opens the plastic clips. Be
gentle, as these clips are very cheap and break quickly.
Installation
------------
1. Connect to the booted device at 192.168.1.20 using username/password
"ubnt".
2. Transfer the OpenWrt sysupgrade image to the device using SCP.
3. Check the mtd partition number for bs / kernel0 / kernel1
$ cat /proc/mtd
4. Set the bootselect flag to boot from kernel0
$ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock6
5. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1
$ dd if=openwrt.bin of=/dev/mtdblock8
$ dd if=openwrt.bin of=/dev/mtdblock9
6. Reboot the device. It should boot into OpenWrt.
Signed-off-by: David Bauer <mail@david-bauer.net>
Add a driver for controlling the RGB LED via Ubiquitis own "LEDBAR" LED
controller based on the Holtek HT32F52241 MCU.
This driver is initially used by the Ubiquiti UniFi 6 LR, however
judging from FCC pictures the MCU is also found on the U6-Mesh as well
as the U6-Extender.
Signed-off-by: David Bauer <mail@david-bauer.net>
