Add patch enabling assisted learning for qca8k to fix roaming issue
between BSS and BSS on the same L2 broadcast domain.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Symbol rtl8366_enable_vlan and rtl8366_reset_vlan are also present in
the DSA driver upstream and conflicts as they are EXPORTED.
Rename them to rtl8366_smi_enable_vlan and rtl8366_smi_reset_vlan to fix
the conflict. While at it also make them static and drop the
EXPORT_SYMBOL_GPL as they are not actually used by any other driver and
exporting them is useless.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
In userspace, ASLR is enabled, but it's missing to enable KASLR on the
kernel side to improve security as part of SystemReady recommendations.
Signed-off-by: Javier Tia <javier.tia@linaro.org>
The name of the variable holding the pointer to the private struct has
changed between Linux 5.15 and Linux 6.1 and adding the identical patch
fixing PCIe #PERST de-assert broke the build on Linux 6.1.
Also change the name in the patch to fix the build.
Fixes: 6a2e17d5c1 ("mediatek: fix PCIe #PERST being de-asserted too early")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fix copy-paste error in migrating NEC Aterm WG2600HP3 to new LED
implementation for the QCA8K switch. Correct define the missing
additional LED pin used for each port and fix wrong color for LED 2 for
each port. Also add the required function-enumerator as all 3 LED have
the same color and function.
Fixes: c707cff6c9 ("ipq806x: add LEDs definition for non-standard qca8k LEDs")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
There are a few targets that mess with the atm kernel headers. To avoid
incompatibility between kernel and user space during compilation, the
correct headers should be used.
Consequently, the package must also be marked as nonshared.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Extreme Networks AP3935i/e -
https://www.extremenetworks.com/support/documentation/access-points-ap3935i-e/
SoC: IPQ8068 QYY AT46279K45060I
RAM: NANYA 1527 NT5CC256M16DP-DI 515073W0EF 7 TW
FLASH: NOR - S25FL256S1 - 32MB
NAND - Macronix MX30UF4G28AB - 512MB
LAN: Atheros AR8035-A J5150WL 1515 CN - RGMII
LAN2: Atheros AR8033-AL1A SKCSR.AJ1 1444 China - SGMII
WLAN2: QCA9990 OVV FNPV209 K451406
WLAN5: QCA9990 OVV FNPV209 K451406
SERIAL: RS232 Port (115200 8n1) Cisco console cable and
4pin Serial Header | 3.3 | GND | RX | TX
MAC address for LAN1/LAN2/WLAN 2G/WLAN 5G in uboot env
* Installation via either RJ45 console or on-board 4 PIN header
Install Method
--------------
1) Setup TFTP server, and place
openwrt-ipq806x-generic-extreme_ap3935-initramfs-uImage image
in /srv/tftp or similar
2) Connect to console on router and connect ethernet port "LAN1" to
your LAN
3) Interupt the boot with any character
4) Login with admin/new2day for default password
(use reset/FactoryDefault if password needs to be reset)
5) Set serverip to TFTP IP: set serverip 192.168.1.2
6) Set ipaddr to another IP: set ipaddr 192.168.1.101
7) Make uboot ping something to activate eth0 on boot:
set bootcmd 'ping 192.168.1.1; run boot_flash'
saveenv
8) TFTP image to RAM:
tftpboot 0x42000000
openwrt-ipq806x-generic-extreme_ap3935i-initramfs-uImage
9) Boot image: bootm 0x42000000
In OpenWRT, "LAN1" is LAN, "LAN2" is WAN
10) SFTP openwrt-ipq806x-generic-extreme_ap3935-squashfs-nand-sysupgrade.bin
image to /tmp
11) sysupgrade /tmp/openwrt-*-nand-sysupgrade.bin
Signed-off-by: Glen Lee <g2lee@yahoo.com>
This script was used to modify the wrong machine type passed
from the boot loader to the kernel. The device tree kernels
does not use the machine type so this script is no longer
needed.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is no point in keeping the v5.15 kernel around for Gemini,
we are maintaining the platform with a strong upstream focus and
newer is always better.
Now that OpenWrt can support pure v6.1 kernels, switch up to
v6.1 and drop v5.15 so we don't need to migrate configs and
patches for no reason.
The USB FOTG2 module handling can be simplified as a result.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix Spanning Tree Protocol (STP) by changing COPY2CPU which currently
makes switch to ignore Bridge Protocol Data Units (BPDUs).
Tested on Zyxel GS1900-8, 24 and 48.
Signed-off-by: Rudolf Vesely <i@rudolfvesely.com>
[ improve commit description and add new line in different sections ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
When cmake is invoked to build a package it usually reports a warning
about unused variables passed to it. This is caused by openwrt passing
all supported variables to cmake, even if they are not all required by
the package being compiled.
To reduce clutter when compiling such packages these warnings are now
suppressed.
Approved-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Tjalling Hattink <t.hattink@fugro.com>
The USXGMII implementation of Realtek switches can not only support
10GbE but also 2.5Gb and 5Gb on top of the usual data rates.
Mark those as supported to allow them to be negotiated.
This change has been tested on a ZyXEL XGS1250-12 with the following link
partners:
- NWA50AX Pro (2.5Gb)
- RTL8152 USB NIC (2.5Gb)
- AQC111 USB NIC (2.5Gb & 5Gb)
Gbit and 10GbE has also been tested to still work fine with a variety of
devices.
Signed-off-by: Tobias Schramm <tobias@t-sys.eu>
This condition was introduced in commit 51c8f76612 ("realtek: Improve
MAC config handling for all SoCs") to correctly report the speed of the
internal serdes ports as 10G, but instead makes all ports read 10G
because the or-operator should have been an and-operator.
Fixes: #9953
Fixes: 51c8f76612 ("realtek: Improve MAC config handling for all SoCs")
Signed-off-by: Peter Körner <git@mazdermind.de>
[ wrap comment to 72 column and improve commit ref ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The driver for MediaTek gen3 PCIe hosts de-asserts all reset
signals at the same time using a single register write operation.
Delay the de-assertion of the #PERST signal by 100ms as some PCIe
devices fail to come up otherwise.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Modems which are using qmi do not reply on the 1st sync but they do
on subsequent. So qmi.sh is hanging on the first call. Since 2020 uqmi
supports a timeout parameter. Unfortunately qmi.sh didn't make use of
this parameter. So qmi.sh is now invoking an early dummy access to
unlock the modem
Signed-off-by: Uwe Niethammer <uwe@dr-niethammer.de>
Add missing PKG_MIRROR_HASH. This is always needed as is used to
generate and use a tar instead of git clone and validate the hash of it.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Google WiFi board has what seems as debug version of TZ/QSEE and it is
always enabling SDI (Secure Debug Image) and in order to do a regular
reboot it must be disabled, as otherwise you are stuck in a debug state
where you are supposed to extract debug logs via QCA tooling which is not
helpfull at all for regular users.
So, instead of using our downstream version to disable SDI lets use the
version that was merged upstream and relies on a boolean property in the
SCM node instead of checking the compatible.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Tested-by: Brian Norris <computersforpeace@gmail.com>
Improve and update instructions on how to add board files and both
describe the needed step to upstream a board file or to use it locally.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The PKG_MIRROR_HASH is wrong, fix it.
Found and fixed using this command:
make package download check FIXUP=1
Fixes: c123e4f053 ("rtl8812au-ct: bump to fix kernel 6.1 compile")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Commit mt76: drop default eeprom file for mt7986-firmware
(e3aa645b26) breaks eeprom loading for
Mercusys MR90X v1. As a result WiFi is not working at all.
This commit adds Mercusus MR90x to the caldata script (it works after the
commit mentioned above). And we can safely drop "81_fix_eeprom" script
as it's no longer required.
Fixes: e3aa645b26
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Add patch fixing regression from stmmac TX timer.
Refer to the single patch for extensive details on the problem.
This should restore original performance before 4.19 kernel.
Fixes: #11676
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch fixing regression from stmmac TX timer.
Refer to the single patch for extensive details on the problem.
This should restore original performance before 4.19 kernel.
Fixes: #11676
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add LEDs definition for devices that use a non-standard qca8k LEDs
configuration.
This is to restore original setup of the LED and be on par with swconfig
old configuration.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Enable and setup multi-cpu for qca8k switch for ipq806x based devices.
Rework each DTS to enable the secondary CPU port on QCA8K switch and
apply the required values originally set by the OEM in the old swconfig
node.
In original firmware the first CPU port was always assigned to the WAN
port and the secondary CPU port was assigned to the rest of the LAN
port. Follow this original implementation using an init.d script.
To setup the CPU port ip tools is required. Add additional default
package ip-tiny to correctly setup the CPU port.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport pending patch for multi CPU port support on QCA8K. 6.1 already
supports all the requiredt code to change a DSA master port so only this
patch fixing the driver is required.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport various QCA8K fixes patch merged upstream. Refresh any changed
patches due to backports.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop and move ASRock G10 preinit script to fix mac address to generic
board.d script and rework for consistency with other devices following a
similar implementation.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Convert each ipq806x device to DSA implementation using the qca8k
driver. Rework 02_network to follow the new naming scheme.
Update 01_leds to use netdev trigger with correct DSA port and drop
now unused switch trigger.
Currently secondary CPU is disabled and will be reneabled later.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Recent hostapd changes just edited the ucode files. It is required to
bump the PKG_RELEASE to include the newest changes in the latest builds.
Signed-off-by: Nick Hainke <vincent@systemli.org>
The mt76 driver usually reads the eeprom on the mtd partition at dts.
For emmc device we need to use caldata_extract script to read the
eeprom. However, the default eeprom file breaks the caldata script
execution, so remove it.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
When adding new router support, I found that uboot
could not recognize flash: "unknown raw ID xxx".
Sync SPI-NAND driver for mediatek to fixes this:
* Add support for Winbond W25N01KV 1Gbit chip.
* Add support for Etron SPI-NAND chip.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
If the full interface is restarted while bringing up an AP, it can trigger a
wpa_supplicant interface start before wpa_supplicant is notified of the
allocated mac addresses.
Fix this by moving the iface_update_supplicant_macaddr call to just after
the point where mac addresses are allocated.
Reported-by: Michael-cy Lee (李峻宇) <Michael-cy.Lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The reset button was missing from the Enterasys WS-AP3715i DTS.
Add the node required for making the reset button work.
Signed-off-by: David Bauer <mail@david-bauer.net>
