Commit Graph

1228 Commits

Author SHA1 Message Date
Raymond Wang
3343ca7e68 ramips: add support for Xiaomi Mi Router CR660x series
Xiaomi Mi Router CR6606 is a Wi-Fi6 AX1800 Router with 4 GbE Ports.
Alongside the general model, it has three carrier customized models:
CR6606 (China Unicom), CR6608 (China Mobile), CR6609 (China Telecom)

Specifications:
- SoC: MediaTek MT7621AT
- RAM: 256MB DDR3 (ESMT M15T2G16128A)
- Flash: 128MB NAND (ESMT F59L1G81MB)
- Ethernet: 1000Base-T x4 (MT7530 SoC)
- WLAN: 2x2 2.4GHz 574Mbps + 2x2 5GHz 1201Mbps (MT7905DAN + MT7975DN)
- LEDs: System (Blue, Yellow), Internet (Blue, Yellow)
- Buttons: Reset, WPS
- UART: through-hole on PCB ([VCC 3.3v](RX)(GND)(TX) 115200, 8n1)
- Power: 12VDC, 1A

Jailbreak Notes:
1. Get shell access.
   1.1. Get yourself a wireless router that runs OpenWrt already.
   1.2. On the OpenWrt router:
      1.2.1. Access its console.
      1.2.2. Create and edit
             /usr/lib/lua/luci/controller/admin/xqsystem.lua
             with the following code (exclude backquotes and line no.):
```
     1  module("luci.controller.admin.xqsystem", package.seeall)
     2
     3  function index()
     4      local page   = node("api")
     5      page.target  = firstchild()
     6      page.title   = ("")
     7      page.order   = 100
     8      page.index = true
     9      page   = node("api","xqsystem")
    10      page.target  = firstchild()
    11      page.title   = ("")
    12      page.order   = 100
    13      page.index = true
    14      entry({"api", "xqsystem", "token"}, call("getToken"), (""),
103, 0x08)
    15  end
    16
    17  local LuciHttp = require("luci.http")
    18
    19  function getToken()
    20      local result = {}
    21      result["code"] = 0
    22      result["token"] = "; nvram set ssh_en=1; nvram commit; sed -i
's/channel=.*/channel=\"debug\"/g' /etc/init.d/dropbear; /etc/init.d/drop
bear start;"
    23      LuciHttp.write_json(result)
    24  end
```
      1.2.3. Browse http://{OWRT_ADDR}/cgi-bin/luci/api/xqsystem/token
             It should give you a respond like this:
             {"code":0,"token":"; nvram set ssh_en=1; nvram commit; ..."}
             If so, continue; Otherwise, check the file, reboot the rout-
             er, try again.
      1.2.4. Set wireless network interface's IP to 169.254.31.1, turn
             off DHCP of wireless interface's zone.
      1.2.5. Connect to the router wirelessly, manually set your access
             device's IP to 169.254.31.3, make sure
             http://169.254.31.1/cgi-bin/luci/api/xqsystem/token
             still have a similar result as 1.2.3 shows.
   1.3. On the Xiaomi CR660x:
        1.3.1. Login to the web interface. Your would be directed to a
               page with URL like this:
               http://{ROUTER_ADDR}/cgi-bin/luci/;stok={STOK}/web/home#r-
               outer
        1.3.2. Browse this URL with {STOK} from 1.3.1, {WIFI_NAME}
               {PASSWORD} be your OpenWrt router's SSID and password:
               http://{MIROUTER_ADDR}/cgi-bin/luci/;stok={STOK}/api/misy-
               stem/extendwifi_connect?ssid={WIFI_NAME}&password={PASSWO-
               RD}
               It should return 0.
        1.3.3. Browse this URL with {STOK} from 1.3.1:
               http://{MIROUTER_ADDR}/cgi-bin/luci/;stok={STOK}/api/xqsy-
               stem/oneclick_get_remote_token?username=xxx&password=xxx&-
               nonce=xxx
   1.4. Before rebooting, you can now access your CR660x via SSH.
        For CR6606, you can calculate your root password by this project:
        https://github.com/wfjsw/xiaoqiang-root-password, or at
        https://www.oxygen7.cn/miwifi.
        The root password for carrier-specific models should be the admi-
        nistration password or the default login password on the label.
        It is also feasible to change the root password at the same time
        by modifying the script from step 1.2.2.
        You can treat OpenWrt Router however you like from this point as
        long as you don't mind go through this again if you have to expl-
        oit it again. If you do have to and left your OpenWrt router unt-
        ouched, start from 1.3.
2. There's no official binary firmware available, and if you lose the
   content of your flash, no one except Xiaomi can help you.
   Dump these partitions in case you need them:
   "Bootloader" "Nvram" "Bdata" "crash" "crash_log"
   "firmware" "firmware1" "overlay" "obr"
   Find the corespond block device from /proc/mtd
   Read from read-only block device to avoid misoperation.
   It's recommended to use /tmp/syslogbackup/ as destination, since files
   would be available at http://{ROUTER_ADDR}/backup/log/YOUR_DUMP
   Keep an eye on memory usage though.
3. Since UART access is locked ootb, you should get UART access by modify
   uboot env. Otherwise, your router may become bricked.
   Excute these in stock firmware shell:
    a. nvram set boot_wait=on
    b. nvram set bootdelay=3
    c. nvram commit
   Or in OpenWrt:
    a. opkg update && opkg install kmod-mtd-rw
    b. insmod mtd-rw i_want_a_brick=1
    c. fw_setenv boot_wait on
    d. fw_setenv bootdelay 3
    e. rmmod mtd-rw

Migrate to OpenWrt:
 1. Transfer squashfs-firmware.bin to the router.
 2. nvram set flag_try_sys1_failed=0
 3. nvram set flag_try_sys2_failed=1
 4. nvram commit
 5. mtd -r write /path/to/image/squashfs-firmware.bin firmware

Additional Info:
 1. CR660x series routers has a different nand layout compared to other
    Xiaomi nand devices.
 2. This router has a relatively fresh uboot (2018.09) compared to other
    Xiaomi devices, and it is capable of booting fit image firmware.
    Unfortunately, no successful attempt of booting OpenWrt fit image
    were made so far. The cause is still yet to be known. For now, we use
    legacy image instead.

Signed-off-by: Raymond Wang <infiwang@pm.me>
2022-02-07 00:03:27 +01:00
Hauke Mehrtens
781f2f7300 Revert "kernel: backport MT7530 IRQ support"
This reverts commit 3f4301e123.

This broke the mt7530 on Linksys e8450 (mt7622) for me.
[    1.300554] mt7530 mdio-bus:00: no interrupt support

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-02-05 19:13:15 +01:00
DENG Qingfang
3f4301e123 kernel: backport MT7530 IRQ support
Support MT7530 PHY link change interrupts, and enable for MT7621.

Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-02-05 17:46:59 +02:00
Sven Eckelmann
7c3efd5273 ramips: Switch Teltonika RUT5xx to kernel GPIO-line watchdog driver
The commit 04e91631e0 ("om-watchdog: add support for Teltonika RUT5xx
(ramips)") used the deprecated om-watchdog daemon to handle the GPIO-line
connected watchdog on the Teltonika RUT5xx.

But this daemon has massive problems since commit 30f61a34b4
("base-files: always use staged sysupgrade"). The process will always be
stopped on sysupgrades. If the sysupgrade takes slightly longer, the
watchdog is not triggered at the correct time and thus the sysupgrade will
interrupted hard by the watchdog sysupgrade. And this hard interrupt can
easily brick the device when there is no fallback (dual-boot, ...).

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2022-02-03 22:27:15 +01:00
Stijn Tintel
cd6a6e3030 Revert "ramips: add support for ipTIME AX2004M"
Commit f4a79148f8 ("ramips: add support for ipTIME AX2004M") seems to
leak KERNEL_LOADADDR 0x82000000 to other devices, causing the to no
longer boot. The leak is visible in u-boot:

   Using 'config-1' configuration
   Trying 'kernel-1' kernel subimage
     Description:  MIPS OpenWrt Linux-5.10.92
     Type:         Kernel Image
     Compression:  lzma compressed
     Data Start:   0x840000e4
     Data Size:    10750165 Bytes = 10.3 MiB
     Architecture: MIPS
     OS:           Linux
     Load Address: 0x82000000
     Entry Point:  0x82000000

Normally, it should look like this:

   Using 'config-1' configuration
   Trying 'kernel-1' kernel subimage
     Description:  MIPS OpenWrt Linux-5.10.92
     Type:         Kernel Image
     Compression:  lzma compressed
     Data Start:   0xbfca00e4
     Data Size:    2652547 Bytes = 2.5 MiB
     Architecture: MIPS
     OS:           Linux
     Load Address: 0x80001000
     Entry Point:  0x80001000

Revert the commit to avoid more people soft-bricking their devices.

This reverts commit f4a79148f8.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-02-01 21:35:15 +02:00
Davide Fioravanti
8fde82095b ramips: add support for Wavlink WL-WN535K1
The Wavlink WL-WN535K1 is a "mesh" router with 2 gigabit ethernet ports
and one fast ethernet port. Mine is branded as Talius TAL-WMESH1.
It can be found in kits of 2 or 3 (WL-WN535K2 or WL-WN535K3).
The motherboard is labelled as WS-WN535G3-B-V1.2 so this image could
potentially work for WL-WN535G3R and WS-WN535G3R with little to none
effort, but it's untested.

Hardware
--------
SoC:   Mediatek MT7620A
RAM:   64MB
FLASH: 8MB NOR (GigaDevice GD25Q64CS)
ETH:
  - 2x 10/100/1000 Mbps Ethernet (RTL8211F)
  - 1x 10/100 Mbps Ethernet (integrated in SOC)
WIFI:
  - 2.4GHz: 1x (integrated in SOC) (2x2:2)
  - 5GHz:   1x MT7612E (2x2:2)
  - 4 internal antennas
BTN:
  - 1x Reset button
  - 1x Touchlink button (set to WPS)
  - 1x ON/OFF switch
LEDS:
  - 1x Red led (system status)
  - 1x Blue led (system status)
  - 3x Green leds (ethernet port status/act)
UART:
  - 57600-8-N-1

Everything works correctly.

Currently there is no firmware update available. Because of this, in
order to restore the OEM firmware, you must firstly dump the OEM
firmware from your router before you flash the OpenWrt image.

Backup the OEM Firmware
-----------------------
The following steps are to be intended for users having little to none
experience in linux. Obviously there are many ways to backup the OEM
firmware, but probably this is the easiest way for this router.
Procedure tested on WN535K1_V1510_200916 firmware version.

1) Go to http://192.168.10.1/webcmd.shtml

2) Type the following line in the "Command" input box and then press enter:
	mkdir /etc_ro/lighttpd/www/dev; dd if=/dev/mtd0ro of=/etc_ro/lighttpd/www/dev/mtd0ro

3) After few seconds in the textarea should appear this output:
		16384+0 records in
	16384+0 records out

   If your output doesn't match mine, stop reading and ask for
   help in the forum.

4) Open in another tab http://192.168.10.1/dev/mtd0ro to download the
   content of the whole NOR. If the file size is 0 byte, stop reading
   and ask for help in the forum.

5) Come back to the http://192.168.10.1/webcmd.shtml webpage and type:
	rm /etc_ro/lighttpd/www/dev/mtd0ro;for i in 1 2 3 4 5; do dd if=/dev/mtd${i}ro of=/etc_ro/lighttpd/www/dev/mtd${i}ro; done

6) After few seconds, in the textarea should appear this output:
		384+0 records in
	384+0 records out
	128+0 records in
	128+0 records out
	128+0 records in
	128+0 records out
	14720+0 records in
	14720+0 records out
	1024+0 records in
	1024+0 records out

   If your output doesn't match mine, stop reading and ask for
   help in the forum.

7) Open the following links to download the partitions of the OEM FW:
	http://192.168.10.1/dev/mtd1ro
	http://192.168.10.1/dev/mtd2ro
	http://192.168.10.1/dev/mtd3ro
	http://192.168.10.1/dev/mtd4ro
	http://192.168.10.1/dev/mtd5ro

   If one (or more) of these files are 0 byte, stop reading and ask
   for help in the forum.

8) Store these downloaded files in a safe place.

9) Reboot your router to remove any temporary file in ram.

Installation
------------
Flash the initramfs image in the OEM firmware interface
(http://192.168.10.1/update_mesh.shtml).
When Openwrt boots, flash the sysupgrade image otherwise you won't be
able to keep configuration between reboots.

Restore OEM Firmware
--------------------
Flash the "mtd4ro" file you previously backed-up directly from LUCI.
Warning: Remember to not keep settings!
Warning2: Remember to force the flash.

Notes
-----
1) Router mac addresses:
   LAN		XX:XX:XX:XX:XX:E2 (factory @ 0x28)
   WAN		XX:XX:XX:XX:XX:E3 (factory @ 0x2e)
   WIFI 2G	XX:XX:XX:XX:XX:E4 (factory @ 0x04)
   WIFI 5G	XX:XX:XX:XX:XX:E5 (factory @ 0x8004)

   LABEL	XX:XX:XX:XX:XX:E5

2) The OEM firmware upgrade page accepts only files containing the
   string "WN535K1" in the filename.

3) Additional notes 1,2,3 in the WS-WN583A6 commit are still valid
(92780d80ab)

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
[remove trailing whitespace]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-30 01:15:23 +09:00
Sungbo Eo
f4a79148f8 ramips: add support for ipTIME AX2004M
ipTIME AX2004M is an 802.11ax (Wi-Fi 6) router, based on MediaTek
MT7621A.

Specification:
* SoC: MT7621A
* RAM: 256 MiB
* Flash: NAND 128 MiB
* Wi-Fi:
  * MT7915D: 2.4/5 GHz (DBDC)
* Ethernet: 5x 1GbE
  * Switch: SoC built-in
* USB: 1x 3.0
* UART: J4 (115200 baud)
  * Pinout: [3V3] (TXD) (RXD) (GND)

MAC address:

| interface |        MAC        |     source     | comment
|-----------|-------------------|----------------|---------
|       LAN | 58:XX:XX:00:XX:9B |                | [1]
|       WAN | 58:XX:XX:00:XX:99 |                |
|   WLAN 2G | 58:XX:XX:00:XX:98 | factory 0x4    |
|   WLAN 5G | 5A:XX:XX:40:XX:98 |                |
|           |                   |                |
|           | 58:XX:XX:00:XX:98 | config ethaddr |

[1] Used in this patch as WLAN 5G MAC address with the local bit set

Load address:
* stock
  * 0x80010000: FIT image
  * 0x81001000: kernel image -> entry
* OpenWrt
  * 0x80010000: FIT image
  * 0x82000000: uncompressed kernel+relocate image
  * 0x80001000: relocated kernel image -> entry

Installation via **recovery** mode:
1.  Press reset button, power up the device, wait >10s for CPU LED
    to stop blinking.
2.  Upload recovery image through the recovery web page at 192.168.0.1.

Revert to stock firmware:
1.  Install stock image via recovery mode.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-29 23:50:28 +09:00
Rodrigo Araujo
7c8ade1765 ramips: correct vendor name for COMFAST/Joowin
When Joowin WR758AC V1 and V2 devices were added, they should have been
added with the primary manufacturer name which is COMFAST, since Joowin
is just an alternate vendor name on some coutries or stores.

Fix this by changing the the vendor name on the respective files and set
Joowin as ALT0 variants while ensuring compatibility for early users.
Also adjust the model names to better follow the naming rules.

As a side effect, fix mt76x8 network script which was left incorrectly
unsorted on the case block conditions.

Fixes: 766733e172 ("ramips: add support for Joowin WR758AC V1 and V2")
Signed-off-by: Rodrigo Araujo <araujo.rm@gmail.com>
2022-01-22 01:17:04 +01:00
David Bauer
ef5f3eb700 ramips: read Tenbay T-MB5EU address from single location
Currently the WAN MAC address is read from a different offset contrary
to all other addresses.

There's conflicting information whether offset 0x28 on the factory
partition contains the valid WAN mac for all devices while 0x4 seems to
be uniform.

Read the WAN mac from this location and calculate it.

Signed-off-by: David Bauer <mail@david-bauer.net>
2022-01-22 01:16:56 +01:00
Michael Pratt
74516f4357 ramips: fix reboot for remaining 32 MB boards
The following devices have a Winbond W25Q256FV flash chip,
which does not have the RESET pin enabled by default,
and otherwise would require setting a bit in a status register.

Before moving to Linux 5.4, we had the patch:
0053-mtd-spi-nor-add-w25q256-3b-mode-switch.patch
which kept specific flash chips with explicit 3-byte and 4-byte address modes
to stay in 3-byte address mode while idle (after an erase or write)
by using a custom flag SPI_NOR_4B_READ_OP that was part of the patch.

this was obsoleted by the patch:
481-mtd-spi-nor-rework-broken-flash-reset-support.patch
which uses the newer upstream flag SNOR_F_BROKEN_RESET
for devices with a flash chip that cannot be hardware reset with RESET pin
and therefore must be left in 3-byte address mode when idle.

The new patch requires that the DTS of affected devices
have the property "broken-flash-reset", which was not yet added for most of them.

This commit adds the property for remaining affected devices in ramips target,
specifically because of the flash chip model.

However, it is possible that there are other devices
where the flash chip uses an explicit 4-byte address mode
and the RESET pin is not connected to the SOC on the board,
and those DTS would also need this property.

Ref: 22d982ea00 ("ramips: add support for switching between 3-byte and 4-byte addressing")
Ref: dfa521f129 ("generic: spi-nor: rework broken-flash-reset")
Signed-off-by: Michael Pratt <mcpratt@pm.me>
2022-01-15 17:12:12 +01:00
SeongUk Moon
9c8ccdcdc8 ramips: add support for ipTIME A6004NS-M
ipTIME A6004NS-M is a 2.4/5GHz band AC1900 router, based on MediaTek MT7621A.

Specifications:
- SoC: MediaTek MT7621A (880MHz, Duel-Core)
- RAM: DDR3 256MB
- Flash: SPI NOR 16MB (Winbond W25Q128BV)
- WiFi: MediaTek MT7615E (2.4GHz, 5GHz)
- Ethernet: MediaTek MT7530 (WAN x1, LAN x4, SoC built-in Estimated)
- USB: USB 3.0 x1
- UART: [3.3V, TX, RX, GND] (57600 8N1)

Installation via web interface:
1. Flash initramfs image using OEM's Firmware Update page.
2. Connect to OpenWrt with an SSH connection to `192.168.1.1`.
3. Perform sysupgrade with sysupgrade image.

Revert to stock firmware:
1.  Flash stock firmware via OEM's Recovery mode

How to use OEM's Recovery mode:
1. Power on the device and connect the shell through UART.
2. Connect to the shell and press the `t` key on the keyboard.
3. Set fixed IP with  `192.168.0.2`  with subnet mask  `255.255.255.0`
4. Flash image via TFTP to  `192.168.0.1`

Additional Notes:
1. The higher the 5Ghz Frequency, the lower the stability. It is recommended to use less than 5.775Ghz.
2. If the 5Ghz frequency is too high, 5Ghz may not work.
3. A6ns-M use shared dtsi file of A6004NS-M. (reference: /mt7621_iptime_a6004ns-m.dtsi).

Signed-off-by: SeongUk Moon <antegral@antegral.net>
[convert CRLF to LF]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-15 20:43:14 +09:00
Kyoungkyu Park
6041c693dd ramips: add support for HUMAX E2
HUMAX E2 (also known as HUMAX QUANTUM E2) is a 2.4/5GHz band AC router,
based on MediaTek MT7620A.

Specifications:
- SoC: MT7620A
- RAM: DDR2 64MB
- Flash: SPI NOR 8MB (MXIC MX25L6405D)
- WiFi:
  - 2.4GHz: SoC internal
  - 5GHz: MT7610E
- Ethernet: 1x 10/100Mbps
  - Switch: SoC internal
- UART: J2 (57600 8N1)
  - pinout: [3V3] (RXD) (GND) (TXD)

Installation and Recovery via TFTP:
1. Connect ethernet cable between Router port and PC Ethernet port.
2. Set your computer to a static IP **192.168.1.1**
3. Turn the device off and wait a few seconds. Hold the WPS button on front
   of device and insert power.
4. Send a firmware image to **192.168.1.6** using TFTP.
   You can use any TFTP client. (tftp, curl, Tftpd64...)
5. Wait until Power LED stop flashing. **DO NOT TURN OFF DEVICE!**
   The device will be automatically rebooted.

Signed-off-by: Kyoungkyu Park <choryu.park@choryu.space>
2022-01-15 20:05:46 +09:00
Felix Fietkau
83b14ec026 ramips: enable badblock table support on linksys ea7xxx devices
Use remapping only on the kernel partitions.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-01-13 18:33:06 +01:00
Oskari Lemmela
fdda3130f2 mikrotik: make soft_config writable
Parent mtd partition needs to be writable

Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
2022-01-13 09:33:29 +01:00
Nick McKinney
e0a574d4b7 ramips: add support for Linksys EA6350 v4
Specifications:
- SoC: MT7621DAT (880MHz, 2 Cores)
- RAM: 128 MB
- Flash: 128 MB NAND
- Ethernet: 5x 1GiE MT7530
- WiFi: MT7603/MT7613
- USB: 1x USB 3.0

This is another MT7621 device, very similar to other Linksys EA7300
series devices.

Installation:

Upload the generated factory.bin image via the stock web firmware
updater.

Reverting to factory firmware:

Like other EA7300 devices, this device has an A/B router configuration
to prevent bricking.  Hard-resetting this device three (3) times will
put the device in failsafe (default) mode.  At this point, flash the
OEM image to itself and reboot.  This puts the router back into the 'B'
image and allows for a firmware upgrade.

Troubleshooting:

If the firmware will not boot, first restore the factory as described
above.  This will then allow the factory.bin update to be applied
properly.

Signed-off-by: Nick McKinney <nick@ndmckinney.net>
2022-01-08 00:49:59 +01:00
Liangkuan Yang
bc7d36ba3a ramips: add support for RAISECOM MSG1500 X.00
RAISECOM MSG1500 X.00 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router.
Apart from the general model, there are two ISP customized models:
China Mobile and China Telecom.

Specifications:

- SoC: Mediatek MT7621AT
- RAM: 256MiB DDR3
- Flash: 128MiB NAND
- Ethernet: 5 * 10/100/1000Mbps: 4 * LAN + 1 * WAN
  - Switch: MediaTek MT7530 (SoC)
- WLAN: 1 * MT7615DN Dual-Band 2.4GHz 2T2R (400Mbps) 5GHz 2T2R (867Mbps)
- USB: 1 * USB 2.0 port
- Button: 1 * RESET button, 1 * WPS button, 1 * WIFI button
- LED: blue color: POWER, WAN, WPS, 2.4G, 5G, LAN1, LAN2, LAN3, LAN4, USB
- UART: 1 * serial port header (4-pin)
- Power: DC 12V, 1A
  - Switch: 1 * POWER switch

MAC addresses as verified by vendor firmware:

use   address             source
LAN   C8:XX:XX:3A:XX:E7   Config   "protest_lan_mac"  ascii  (label)
WAN   C8:XX:XX:3A:XX:EA   Config   "protest_wan_mac"  ascii
5G    C8:XX:XX:3A:XX:E8   Factory  "0x4"              hex
2.4G  CA:XX:XX:4A:XX:E8   [not on flash]

The increment of the 4th byte for the 2.4g address appears to vary.
Reported cases:

       5g                 2.4g         increment
 C8:XX:XX:90:XX:C3  CA:XX:XX:C0:XX:C3  0x30
 C8:XX:XX:3A:XX:08  CA:XX:XX:4A:XX:08  0x10
 C8:XX:XX:3A:XX:E8  CA:XX:XX:4A:XX:E8  0x10

Since increment is inconsistent and there is no obvious pattern
in swapping bytes, and the 2.4g address has local bit set anyway,
it seems safer to use the LAN address with flipped byte here in
order to prevent collisions between OpenWrt devices and OEM devices
for this interface. This way we at least use an address as base
that is definitely owned by the device at hand.

Notes:

1. The vendor firmware allows you to connect to the router by telnet.
   (known version 1.0.0 can open telnet.)
   There is no official binary firmware available.
   Backup the important partitions data:
   "Bootloader", "Config", "Factory", and "firmware".
   Note that with the vendor firmware the memory is detected only 128MiB
   and the last 512KiB in NAND flash is not used.

2. The POWER LED is default on after press POWER switch.
   The WAN and LAN1 - 4 LEDs are wired to ethernet switch.
   The WPS LED is controlled by MT7615DN's GPIO.
   Currently there is no proper way to configure it.

3. At the time of adding support the wireless config needs to be set up
   by editing the wireless config file:

 * Setting the country code is mandatory, otherwise the router loses
   connectivity at the next reboot. This is mandatory and can be done
   from luci. After setting the country code the router boots correctly.
   A reset with the reset button will fix the issue and the user has to
   reconfigure.

 * This is minor since the 5g interface does not come up online although
   it is not set as disabled. 2 options here:

   1- Either run the "wifi" command. Can be added from LuCI in system -
      startup - local startup and just add wifi above "exit 0".

   2- Or add the serialize option in the wireless config file as shown
      below. This one would work and bring both interfaces automatically
      at every boot:

      config wifi-device 'radio0'
          option serialize '1'

      config wifi-device 'radio1'
          option serialize '1'

Flash instructions using initramfs image:

1. Press POWER switch to power down if the router is running.

2. Connect PC to one of LAN ports, and set
   static IP address to "10.10.10.2", netmask to "255.255.255.0",
   and gateway to "10.10.10.1" manually on the PC.

3. Push and hold the WIFI button, and then power up the router.
   After about 10s (or you can call the recovery page, see "4" below)
   you can release the WIFI button.
   There is no clear indication when the router
   is entering or has entered into "RAISECOM Router Recovery Mode".

4. Call the recovery page for the router at "http://10.10.10.1".
   Keep an eye on the "WARNING!! tip" of the recovery page.
   Click "Choose File" to select initramfs image, then click "Upload".

5. If image is uploaded successfully, you will see the page display
   "Device is upgrading the firmware... %".
   Keep an eye on the "WARNING!! tip" of the recovery page.
   When the page display "Upgrade Successfully",
   you can set IP address as "automatically obtain".

6. After the rebooting (PC should automatically obtain an IP address),
   open the SSH connection, then download the sysupgrade image
   to the router and perform sysupgrade with it.

Flash back to vendor firmware:

 See "Flash instructions 1 - 5" above.
 The only difference is that in step 4
 you should select the vendor firmware which you backup.

Signed-off-by: Liangkuan Yang <ylk951207@gmail.com>
2022-01-08 00:49:59 +01:00
Rodrigo Araujo
766733e172 ramips: add support for Joowin WR758AC V1 and V2
This commit adds support for Joowin (aka Comfast) WR758AC V1 and V2
devices.

Both have the same wall AP/repeater form factor and differ only
in the 5Ghz chipset (V1 has MT7662, V2 has MT7663).

OpenWrt developers forum page:
https://forum.openwrt.org/t/87355

Specifications:

 - CPU: MediaTek MT7628AN (580MHz)
 - Flash: 8MB
 - RAM: 64MB DDR2
 - 2.4 GHz: 802.11b/g/n (MT7603)
 - 5 GHz: 802.11ac (V1 has MT7662, V2 has MT7663)
 - Antennas: 4x external single band antennas
 - LAN: 1x 10/100M
 - LED: Wifi 3x blue. Programmable
 - Button: WPS

MAC addresses as verified by OEM firmware:

use address source
LAN *:83 factory 0xe000
2g *:85 factory 0x4
5g *:86 factory 0x8004

How to install:
1- Setup a TFTP server on a machine with IP address 192.168.1.10/24
2- Name the image as `firmware_auto.bin` and place it on the root of the
TFTP server
3- Connect the device via Ethernet, it should pick and flash the image

Signed-off-by: Rodrigo Araujo <araujo.rm@gmail.com>
2022-01-08 00:49:59 +01:00
Sungbo Eo
a1deab0ec9 ramips: add support for ipTIME T5004
ipTIME T5004 is a 5-port Gigabit Ethernet router, based on MediaTek MT7621A.

Specifications:
* SoC: MT7621AT
* RAM: 128 MiB
* Flash: NAND 128 MiB
* Ethernet: 5x 1GbE
  * Switch: SoC built-in
* UART: J4 (57600 baud)
  * Pinout: [3V3] (TXD) (RXD) (GND)

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware via recovery mode:
1.  Press reset button, power up the device, wait >15s for CPU LED
    to stop blinking.
2.  Upload stock image to TFTP server at 192.168.0.1.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-02 00:50:43 +09:00
WonJung Kim
2dde2416e1 ramips: add support for ipTIME A3004T
ipTIME A3004T is a 2.4/5GHz band router, based on Mediatek MT7621.

Specifications:
 - SoC: MT7621 (880MHz)
 - RAM: DDR3 256M
 - Flash: NAND 128MB  (Macronix NAND 128MiB 3,3V 8-bit)
 - WiFi:
   - 2.4GHz: MT7615E
   - 5GHz : MT7615E
 - Ethernet:
   - 4x LAN
   - 1x WAN
 - USB: 1 * USB3.0 port
 - UART:
   - 3.3V, TX, RX, GND / 57600 8N1

Installation via web interface:
 1. Flash initramfs image using OEM's Recovery mode
 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
 - Flash stock firmware via OEM's Recovery mode

How to use OEM's Recovery mode:
 1. Power up with holding down the reset key until CPU LED stop blinking.
 2. Set fixed ip with `192.168.0.2` with subnet mask `255.255.255.0`
 3. Flash image via tftp to `192.168.0.1`

Additional Notes:
 This router shares one MT7915E chip for both 2.4Ghz/5Ghz.
 radio0 will not working on 5Ghz as it's not connected to the antenna.

Signed-off-by: WonJung Kim <git@won-jung.kim>
(added led dt-bindings)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-29 20:35:57 +01:00
Sungbo Eo
482a7e23a4 ramips: add support for WeVO AIR DUO
WeVO AIR DUO is a 1-bay NAS & 802.11ac (Wi-Fi 5) router, based on
MediaTek MT7620A.

Specifications:
* SoC: MT7620A
* RAM: 64 MiB
* Flash: SPI NOR 16 MiB
* USB & SATA bridge controller: JMicron JMS567
  * SATA 6Gb/s: 2.5" drive slot
  * USB 3.0: Micro-B
  * USB 2.0: connected to SoC
* Wi-Fi:
  * 2.4 GHz: SoC built-in
  * 5 GHz: MT7612EN
* Ethernet: 5x 1GbE
  * Switch: MT7530WU
* UART: 4-pin 1.27 mm pitch through-hole (57600 baud)
  * Pinout: (3V3)|(RXD) (TXD) (GND)

Notes:
* The drive is accessible through the external USB port only when the
  router is turned off.

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
    The image filename should have ".upload" extension.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2021-12-29 20:35:57 +01:00
David Bauer
b1d483b865 ramips: work around duplicate MAC address on U6 Lite
The UniFi 6 Lite has two MAC addresses for the 2.4 and 5GHz radio in
it's EEPROM partition.

On my unit these are

F4 92 BF A0 BB 6F
F6 92 BF A0 BB 6F

The problem with these is that mac80211 increases the first octet by
2, which leads to conflicting MAC addresses between radios.

Work around this problem for now by increasing the last octet by 1 on
the 5 GHz radio.

Ubiquiti increases the last octet by 2 for each subsequent VAP created
per radio. Ideally we should do the same, however this functionality is
currently lacking from mac80211.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-12-20 00:12:12 +01:00
Pawel Dembicki
794e8123ce ramips: mt7620: use OKLI loader with Jboot devices
Jboot devices have problem with >2MB kernelsize. The only way to avoid
this problem is use small loader.

This patch switch all mt7620 Jboot devices to lzma OKLI loader.

Suggested-by: Szabolcs Hubai <szab.hu@gmail.com>
Co-authored-by: Michael Pratt <mcpratt@pm.me>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2021-12-13 19:36:10 +01:00
Kyoungkyu Park
9a1b9a42b7 ramips: add support for HUMAX E10
HUMAX E10 (also known as HUMAX QUANTUM E10) is a 2.4/5GHz band AC router,
based on MediaTek MT7621A.

Specifications:
- SoC: MT7621A
- RAM: DDR3 128MB
- Flash: SPI NOR 16MB (MXIC MX25L12805D)
- WiFi:
  - 2.4GHz: MT7615
  - 5GHz: MT7615
- Ethernet: 2x 10/100/1000Mbps
  - Switch: SoC internal
- USB: 1x USB 2.0 Type-A
- UART: J1 (57600 8N1)
  - pinout: [3V3] (RXD) (GND) (TXD)

Installation via web interface:
- Flash **factory** image through the stock web interface.

Recovery procedure:
1. Connect ethernet cable between Router **LAN** port and PC Ethernet port.
2. Set your computer to a static IP **192.168.1.1**
3. Turn the device off and wait a few seconds. Hold the WPS button on front
   of device and insert power.
4. Send a firmware image to **192.168.1.6** using TFTP.
   You can use any TFTP client. (tftp, curl, Tftpd64...)
- It can accept both images which is
  HUMAX stock firmware dump (0x70000-0x1000000) image
  and OpenWRT **sysupgrade** image.

Signed-off-by: Kyoungkyu Park <choryu.park@choryu.space>
[remove trailing whitespace]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2021-12-12 20:33:19 +09:00
Sergey Ryazanov
7e89421a7c ramips: add support for Zbtlink ZBT-WG1602
Zbtlink ZBT-WG1602 is a Wi-Fi router intendent to use with WWAN
(UMTS/LTE/3G/4G) modems. The router board offsers a couple of miniPCIe
slots with USB and SIM only and another one pure miniPCIe slot as well
as five Gigabit Ethernet ports (4xLAN + WAN).

Specification:

* SoC: MT7621A
* RAM: 256/512 MiB
* Flash: 16/32 MiB (SPI NOR)
* external watchdog (looks like Torexsemi XC6131B)
* Eth: 10/100/1000 Mbps Ethernet x5 ports (4xLAN + WAN)
* WLAN 2GHz: MT7603EN (.11n, MIMO 2x2)
* WLAN 5GHz: MT7612EN (.11ac, MIMO 2x2)
* WLAN Ants: detachable x2, shared by 2GHz & 5GHz radios
* miniPCIe: 2x slots with USB&SIM + 1x slot with regular PCIe bus
* WWAN Ants: detachable x4
* External storage: microSD (SDXC) slot
* USB: 2.0 Type-A port
* LED: 11 (5 per Eth phy, 3 SoC controlled, 2 WLAN 2/5 controlled, 1
       power indicator)
* Button: 1 (reset)
* UART: console (115200 baud)
* Power: DC jack (12 V / 2.5 A)

Additional HW information:

* SoC USB port #1 is shared by internal miniPCIe slot and external
  Type-A USB port, USB D+/D- lines are toggled between ports using a
  GPIO controlled DPDT switch.
* Power of the USB enabled miniPCIe slots can be individually controlled
  using dedicated GPIO lines.
* Vendor firmware feeds the external watchdog with 1s pulses. GPIO
  watchdog driver is able to either generate a 1us pulses or toggle the
  output line. 1us is not enough for the external watchod timer, so
  the line toggling driver mode is utilized.

Installation:

Vendor's firmware is OpenWrt (LEDE) based, so the sysupgrade image can
be directly used to install OpenWrt. Firmware must be upgraded using the
'force' and 'do not save configuration' command line options (or
correspondig web interface checkboxes) since the vendor firmware is from
the pre-DSA era.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2021-12-05 18:49:14 +01:00
Yuchan Seo
c33eb0372e ramips: add support for ipTIME A3004NS-dual
ipTIME A3004NS-dual is a 2.4/5GHz band router, based on Mediatek MT7621.

Specifications:
- SoC: MT7621 (880MHz)
- RAM: DDR3 256M
- Flash: SPI NOR 16MB
- WiFi:
 - 2.4GHz: MT7602E
 - 5GHz : MT7612E
- Ethernet:
 - 4x LAN
 - 1x WAN
- USB: 1 * USB3.0 port
- UART:
  - 3.3V, TX, RX, GND / 57600 8N1

Installation via web interface:
- 1. Flash Initramfs image using OEM Firmware's web GUI
- 2. Boot into OpenWrt and perform Sysupgrade with sysupgrade image.

Revert to stock firmware:
- 1. Boot into OpenWrt and perform Sysupgrade with OEM Stock Firmware image.

Signed-off-by: Yuchan Seo <hexagonwin@disroot.org>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
2021-12-04 09:39:11 +09:00
Pawel Dembicki
a82fa5bcd4 ramips: mt7620: Enable PHY aneg of Lava LR-25G001
In 20b09a2125 Lava LR-25G001 router have problem with two inactive
ethernet ports. JBOOT bootloader didn't configure ethernet devices by default.
The same situation was there. It is required to enable all phy ports.
This is fragment of stock bootlog:

switch reg write_athr offset=90, value=2b0
switch reg write_athr offset=8c, value=2b0
switch reg write_athr offset=88, value=2b0
switch reg write_athr offset=84, value=2b0
switch reg write_athr offset=80, value=2b0

This patch adds proper registers configuration ar8337 initvals.
0x2b0 value causes force flow control configuration, 0x1200 was used
instead (flow control config auto-neg with phy). [1]

When switch is now ok, let's fix port numeration too.

Fixes: 20b09a2125 ("ramips: add support for Lava LR-25G001")

[1] https://github.com/openwrt/openwrt/pull/4806#issuecomment-982019858

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2021-12-04 00:36:47 +01:00
Thomas Aldrian
b28443f82e ramips: add support for Wavlink WL-WN576A2
This commit adds support for the Wavlink WL-WN576A2 wall-plug wireles
repeater / router. It is also sold under the name SilverCrest SWV 733 B1.

Device specs:

- CPU: MediaTek MT7628AN
- Flash: 8MB
- RAM: 64MB
- Bootloader: U-Boot
- Ethernet: 1x 10/100 Mbps
- 2.4 GHz: b/g/n SoC
- 5 GHz: a/n/ac MT7610EN
- Buttons: WPS, reset, sliding switch (ap/repeater)
- LEDs: 5x wifi status, 1x LAN/WAN, 1x WPS

Flashing:

U-Boot launches a TFTP client if WPS button is held during boot.

- Server IP: 192.168.10.100
- Firmware file name: firmware.bin

Device will reboot automatically. First boot takes about 90s.

Coelner (waenger@gmail.com) is the original author, but I have made some
fixes. He does not wish to sign off using his real name.

Signed-off-by: Thomas Aldrian <dev.aldrian@gmail.com>
2021-11-20 21:08:25 +01:00
Wout Bertrums
9a7e3d170c ramips: add broken-flash-reset for HLK-7621A EvB
This is needed because the HLK-7621 EvB has 32MB of flash,
so it will have to use 4B addressing and the
broken-flash-reset hack has to be used to be able to reboot.

Signed-off-by: Wout Bertrums <wout@wbnet.eu>
[copied github message into commit message]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-11-06 23:36:32 +01:00
Sergio Paracuellos
8bc6654244 ramips: mt7621-dts: properly organize pcie node
Device tree pcie node for this SoC is using different
styles in its different properties. Hence properly
unify them to be able to write a a proper yaml schema
documentation.

Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20210505121736.6459-11-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-11-06 23:36:32 +01:00
Sergio Paracuellos
2bc659ee07 ramips: mt7621-dts: add missing device_type in pcie root ports
According to the YAML schema 'pci-bus.yaml' the 'device_type'
property is mandatory for all pcie root ports. Hence add it.

Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20210506170742.28196-3-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-11-06 23:36:32 +01:00
Sergio Paracuellos
82f9d5ad0b ramips: mt7621-dts: remove 'bug-range' property
Property 'bus-range' when values are the default are
not necessary to be defined. Hence, remove all of them.

Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20210506170742.28196-2-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-11-06 23:36:32 +01:00
Sergio Paracuellos
e04130fc17 ramips: mt7621-dts: use standard 'syscon' string
Both 'memc' and 'sysc' nodes are not using 'syscon'
as a node string which is the standard one to be used.
Update both of them.

Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20210505132154.8263-3-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-11-06 23:36:32 +01:00
Sergio Paracuellos
f1d154ec6c ramips: mt7621-dts: remove ethsys node
DT 'ethsys' node is being configured as a syscon
to get access to reset and other registers in the
'mediateķ,mt7621-eth' driver. Since the 'sysc' is also
a syscon, provides the clock and also is virtually
mapped from the same physical address 0x1e000000 we
can just use 'sysc' as the phandle for the syscon in
the ethernet node. Compatible string 'mediatek,mt7621-ethsys'
of the node is not being used anywhere inside the kernel
so, this node can be safely removed.

Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20210505132154.8263-2-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-11-06 23:36:32 +01:00
DENG Qingfang
93da227798 ramips: mt7621-dts: remove obsolete switch node
This was for OpenWrt's swconfig driver, which never made it upstream,
and was also superseded by MT7530 DSA driver.

Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Link: https://lore.kernel.org/r/20210108025155.31556-1-dqfext@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-11-06 23:36:32 +01:00
Sergio Paracuellos
6e30692e99 ramips: mt7621-dts: properly define 'cpc' and 'mc' nodes
'cpc' and 'mc' nodes correspond with the MIPS 'Cluster Power Controller'
and 'MIPS Common Device Memory Map' which are present in some MIPS related
boards. There is already bindings documentation for these two located in:
- Documentation/devicetree/bindings/power/mti,mips-cpc.yaml
- Documentation/devicetree/bindings/bus/mti,mips-cdmm.yaml

Hence, properly update compatible strings and align nodes with already
mainlined bindings documentation. Also, move their definition to a proper
place since both of them are not related with the palmbus at all.

Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20211002060706.30511-1-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-11-06 23:36:32 +01:00
Sergio Paracuellos
9b52b4e53f ramips: mt7621-dts: change some node hex addresses to lower case
Hexadecimal addresses in device tree must be defined using lower case.
There are some of them that are still in upper case. Change them all.

Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20211017070656.12654-2-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-11-06 23:36:32 +01:00
Sergio Paracuellos
e17f238f1d ramips: mt7621-dts: make use of 'IRQ_TYPE_LEVEL_HIGH' instead of magic numbers
Nodes 'gdma' and 'hsdma' are using magic number '4' in interrupts property.
Use 'IRQ_TYPE_LEVEL_HIGH' instead to align with the rest of the nodes in
the file.

Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20211019102915.15409-2-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-11-06 23:36:32 +01:00
Sergio Paracuellos
eb00fb8f71 ramips: add support for HiLink HLK-7621A evaluation board
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 256 MB (DDR3)
- Flash: 32 MB SPI NOR 44MHz
- Switch: 1 WAN, 4 LAN (Gigabit)
- LEDs: 1 WAN, 4 LAN (controlled by PHY)
- USB Ports: 1 x USB2, 1 x USB3
- WLAN: 1 x 2.4, 5 GHz 866Mbps (MT7612E)
- Button: 1 button (reset)
- UART Serial: UART1 as console : 57600 baud
- Power: 12VDC, 1A

Installation:
Update openWRT firmware using internal GNUBEE uboot:
https://github.com/gnubee-git/GnuBee-MT7621-uboot

By HTTP: Initial uboot address is http://10.10.10.123, your address
needs to be 10.10.10.x, and mask 255.255.255.0.
By TFTP: Uboot is in client mode, the address of the firmware must
be tftp://10.10.10.3/uboot.bin

Recovery:
Manufacturer provides MTK OpenWrt 14.07 source code, compile then
flash it by uboot.
HLK-7621A is a stamp hole package module for embedded development,
users have to design IO boards to use it.

MAC addresses:
- u-boot-env contains a placeholder address:
  > mtd_get_mac_ascii u-boot-env ethaddr
  03:17:73🆎cd:ef
- phy0 gets a valid-looking address:
  > cat /sys/class/ieee80211/phy0/macaddress
  f8:62:aa:**:**:a8
- Calibration data for &pcie2 contains a valid address, however the
  zeros in the right half look like it's not real:
  8c:88:2b:00:00:1b
- Since it's an evaluation board and there is no solid information
  about the MAC address assignment, the ethernet MAC address is left random.

Signed-off-by: Chen Yijun <cyjason@bupt.edu.cn>
[add keys and pcie nodes to properly support evaluation board]
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
[remove ethernet address, wrap lines properly]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-10-31 21:24:47 +01:00
Eduardo Santos
3c97fb4346 ramips: add support for Xiaomi MiWifi 3C
This commit adds support for Xiaomi MiWiFi 3C device.

Xiaomi MiWifi 3C has almost the same system architecture
as the Xiaomi Mi WiFi Nano, which is already officially
supported by OpenWrt.

The differences are:

 - Numbers of antennas (4 instead of 2). The antenna management
   is done via the µC. There is no configuration needed in the
   software code.
 - LAN port assignments are different. LAN1 and WAN are
   interchanged.

OpenWrt Wiki: https://openwrt.org/toh/xiaomi/mir3c

OpenWrt developers forum page:
https://forum.openwrt.org/t/support-for-xiaomi-mi-3c

Specifications:

 - CPU: MediaTek MT7628AN (575MHz)
 - Flash: 16MB
 - RAM: 64MB DDR2
 - 2.4 GHz: IEEE 802.11b/g/n with Integrated LNA and PA
 - Antennas: 4x external single band antennas
 - WAN: 1x 10/100M
 - LAN: 2x 10/100M
 - LED: 1x amber/blue/red. Programmable
 - Button: Reset

MAC addresses as verified by OEM firmware:

use address source
LAN *:92 factory 0x28
WAN *:92 factory 0x28
2g *:93 factory 0x4

OEM firmware uses VLAN's to create the network interface for WAN and LAN.

Bootloader info:
The stock bootloader uses a "Dual ROM Partition System".
OS1 is a deep copy of OS2.
The bootloader start OS2 by default.
To force start OS1 it is needed to set "flag_try_sys2_failed=1".

How to install:
1- Use OpenWRTInvasion to gain telnet, ssh and ftp access.
   https://github.com/acecilia/OpenWRTInvasion
   (IP: 192.168.31.1 - Username: root - Password: root)
2- Connect to router using telnet or ssh.
3- Backup all partitions. Use command  "dd if=/dev/mtd0 of=/tmp/mtd0".
   Copy /tmp/mtd0 to computer using ftp.
4- Copy openwrt-ramips-mt76x8-xiaomi_miwifi-3c-squashfs-sysupgrade.bin
   to /tmp in router using ftp.
5- Enable UART access and change start image for OS1.
```
nvram set uart_en=1
nvram set flag_last_success=1
nvram set boot_wait=on
nvram set flag_try_sys2_failed=1
nvram commit
```
6- Installing Openwrt on OS1 and free OS2.
```
mtd erase OS1
mtd erase OS2
mtd -r write /tmp/openwrt-ramips-mt76x8-xiaomi_miwifi-3c-squashfs-sysupgrade.bin OS1
```

Limitations: For the first install the image size needs to be less
than 7733248 bits.

Thanks for all community and especially for this device:
minax007, earth08, S.Farid

Signed-off-by: Eduardo Santos <edu.2000.kill@gmail.com>
[wrap lines, remove whitespace errors, add mediatek,mtd-eeprom to
 &wmac, convert to nvmem]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-10-31 21:24:47 +01:00
Jani Partanen
e06aaba4e3 ramips: fix LAVA LR-25G001 broken wifi led triggers
LED labels for this device are different in 01_leds file and in device
DTS. Switch to DT triggers, which works on Telewell TW-4 (LTE) clone
device.

This has not been tested on the LR-25G001 itself, just on the clone
mentioned above.

Fixes: 20b09a2125 ("ramips: add support for Lava LR-25G001")

Signed-off-by: Jani Partanen <rtfm@iki.fi>
[rephrase commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-10-30 22:11:23 +02:00
Michal Kozuch
c12ef2f760 ramips: add support for TP-Link RE305 v3
Specs (same as in v1):
- MT7628AN (575 MHz)
- 64MB RAM
- 8MB of flash (SPI NOR)
- 1x 10/100Mbps Ethernet (MT7628AN built-in switch with vlan)
- 1x 2.4GHz wifi (MT7628AN)
- 1x 5Ghz wifi (MT7612E)
- 4x LEDs (5 GPIO-controlled)
- 1x reset button
- 1x WPS button

The only and important difference between v1 & v3 is in flash memory
layout, so pls don't interchange these 2 builds!

Installation through web-ui (on OEM factory firmware):
1. Visit http://tplinkrepeater.net or the configured IP address of
   your RE305 v3 (default 192.168.0.254).
2. Log in with the password you've set during initial setup of the
   RE305 (there is no default password).
3. Go to Settings -> System Tools -> Firmware upgrade
4. Click Browse and select the OpenWRT image with factory.bin suffix
   (not sysupgrade.bin)
5. A window with a progress bar will appear. Wait until it completes.
6. The RE305 will reboot into OpenWRT and serve DHCP requests on the
   ethernet port.
7. Connect an RJ45 cable from the RE305 to your computer and access
   LuCI at http://192.168.1.1/ to configure (or use ssh).

Disassembly:
Just unscrew 4 screws in the corners & take off the back cover.
Serial is exposed to the right side of the main board (in the middle)
and marked with TX/RX/3V3/GND, but the holes are filled with solder.

Installation through serial:
1. connect trough serial (1n8, baudrate=57600)
2. setup the TFTP server and connect it via ethernet
   (ipaddr=192.168.0.254 of device, serverip=192.168.0.184 - your pc)
3. boot from a initramfs image first (choose 1 in the bootloader
   options)
4. test it a bit with that, then proceed to run sysupgrade build

MAC addresses as verified by OEM firmware:

  use  OpenWrt  address  reference
  LAN  eth0     *:d2     label
  2g   wlan0    *:d1     label - 1
  5g   wlan1    *:d0     label - 2

  The label MAC address can be found in config 0x2008.

Signed-off-by: Michal Kozuch <servitkar@gmail.com>
[redistribute WLAN node properties between DTS/DTSI, remove
 compatible on DTSI, fix indent/wrapping, split out firmware-utils
 change]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-10-30 22:05:25 +02:00
Bruno Randolf
2c3e8bed3f
ramips: minew g1-c: Allow dynamic RAM sizes
Allow RAM size to be passed thru U-Boot. There are 128MB and 64MB
versions of Minew G1-C. This is also in line with the behaviour of
most other RAMIPS boards.

Signed-off-by: Bruno Randolf <br1@einfach.org>
2021-10-26 13:59:30 +02:00
Rosen Penev
5b3d62247c ramips: fix dtc warnings for telco-electronics_x1
In all other dts files, the entire block is not edited like this.
They're edited separately.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2021-10-17 15:21:37 +02:00
David Bauer
f82c93b93c ramips: fix USW-Flex reversed switch-port order
Switch port order was reversed due to reading the internal labling
(which mismatches the one on the case).

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-10-04 23:24:32 +02:00
Dale Hui
830c2e5378 ramips: add support for Netgear R7450
Netgear R7450 is a clone of Netgear R6700v2

Specifications
==============
SoC: MediaTek MT7621AT
RAM: 256M DDR3
FLASH: 128M NAND
WiFi: MediaTek MT7615N an+ac
MediaTek MT7615N bgn
ETH: MediaTek MT7621AT
BTN: 1x Connect (WPS), 1x WLAN, 1x Reset
LED: Power (white/amber), WAN(white/amber), 2.4G(white), 5G(white),
USB(white) , GuestWifi(white) 4x LAN(white/amber), Wifi Button(white),
WPS Button(white)

Flash Instructions
==================
Login to netgear webinterface and flash factory.img

Signed-off-by: Dale Hui <strokes-races0b@icloud.com>
[fix model/compatible in DTS]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-09-26 15:38:01 +02:00
Dale Hui
16fc409e7a ramips: add support for Netgear R6900v2
Netgear R6900v2 is a clone of Netgear R6700v2

Specifications
==============
SoC: MediaTek MT7621AT
RAM: 256M DDR3
FLASH: 128M NAND
WiFi: MediaTek MT7615N an+ac
MediaTek MT7615N bgn
ETH: MediaTek MT7621AT
BTN: 1x Connect (WPS), 1x WLAN, 1x Reset
LED: Power (white/amber), WAN(white/amber), 2.4G(white), 5G(white),
USB(white) , GuestWifi(white) 4x LAN(white/amber), Wifi Button(white),
WPS Button(white)

Flash Instructions
==================
Login to netgear webinterface and flash factory.img

Signed-off-by: Dale Hui <strokes-races0b@icloud.com>
2021-09-26 15:15:36 +02:00
Dale Hui
af3104d25b ramips: make Netgear R7200 a separate device from R6700v2
With the various variants of Netgear R**** devices, make it more
obvious which image should be used for the R7200.

Signed-off-by: Dale Hui <strokes-races0b@icloud.com>
[provide proper commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-09-26 15:15:30 +02:00
David Bauer
a983969789 ramips: add support for Ubiquiti USW-Flex
Hardware
--------
MediaTek MT7621AT
16M SPI-NOR Macronix MX25L12835FMI
Microchip PD69104B1 4-Channel PoE-PSE controller
TI TPS2373 PoE-PD controller

PoE-Controller
--------------

By default, the PoE outputs do not work with OpenWrt. To make them output
power, install the "poemgr" package from the packages feed.
This package can control the PD69104B1 PSE controller.

Installation
------------

1. Connect to the booted device at 192.168.1.20 using username/password
   "ubnt" via SSH.

2. Add the uboot-envtools configuration file /etc/fw_env.config with the
   following content

   $ echo "/dev/mtd1 0x0 0x1000 0x10000 1" > /etc/fw_env.config

3. Update the bootloader environment.

   $ fw_setenv boot_openwrt "fdt addr \$(fdtcontroladdr);
     fdt rm /signature; bootubnt"
   $ fw_setenv bootcmd "run boot_openwrt"

4. Transfer the OpenWrt sysupgrade image to the device using SCP.

5. Check the mtd partition number for bs / kernel0 / kernel1

   $ cat /proc/mtd

6. Set the bootselect flag to boot from kernel0

   $ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock4

7. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1

   $ dd if=openwrt.bin of=/dev/mtdblock6
   $ dd if=openwrt.bin of=/dev/mtdblock7

8. Reboot the device. It should boot into OpenWrt.

Restore to UniFi
----------------

To restore the vendor firmware, follow the Ubiquiti UniFi TFTP
recovery guide for access points. The process is the same for
the Flex switch.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-09-25 21:04:53 +02:00
INAGAKI Hiroshi
7ff0efa0b0 ramips: add support for I-O DATA WN-DX2033GR
I-O DATA WN-DX2033GR is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on
MT7621A.

Specification:

- SoC		: MediaTek MT7621A
- RAM		: DDR3 128 MiB
- Flash		: Raw NAND 128 MiB (Macronix MX30LF1G18AC-TI)
- WLAN		: 2.4/5 GHz
  - 2.4 GHz	: 2T2R, MediaTek MT7603E
  - 5 GHz	: 4T4R, MediaTek MT7615
- Ethernet	: 5x 10/100/1000 Mbps
  - Switch	: MediaTek MT7530 (SoC)
- LEDs/Keys	: 2x/3x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - J5: 3.3V, TX, RX, NC, GND from triangle mark
  - 57600n8
- Power		: 12 VDC, 1 A

Flash instruction using initramfs image:

1. Boot WN-DX2033GR normally
2. Access to "http://192.168.0.1/" and open firmware update page
   ("ファームウェア")
3. Select the OpenWrt initramfs image and click update ("更新") button
   to perform firmware update
4. On the initramfs image, download the sysupgrade.bin image to the
   device and perform sysupgrade with it
5. Wait ~120 seconds to complete flashing

Notes:

- The hardware of WN-DX2033GR and WN-AX2033GR are almost the same, and
  it is certified under the same radio-wave related regulations in Japan

- The last 0x80000 (512 KiB) in NAND flash is not used on stock firmware

- stock firmware requires "customized uImage header" (called as "combo
  image") by MSTC (MitraStar Technology Corp.), but U-Boot doesn't

  - uImage magic ( 0x0 - 0x3 ) : 0x434F4D42 ("COMB")
  - header crc32 ( 0x4 - 0x7 ) : with "data length" and "data crc32"
  - image name   (0x20 - 0x37) : model ID and firmware versions
  - data length  (0x38 - 0x3b) : kernel + rootfs
  - data crc32   (0x3c - 0x3f) : kernel + rootfs

- There are 2x important flags in the flash:

  - bootnum   : select os partition for booting (persist, 0x4)

    - 0x01: firmware
    - 0x02: firmware_2

  - debugflag : allow interrupt kernel loader, it's named as "Z-LOADER"
    (Factory, 0xFE75)

    - 0x00: disable debug
    - 0x01: enable debug

MAC addresses:

LAN     : 50:41:B9:xx:xx:90 (Factory, 0xE000 (hex) / Ubootenv, ethaddr (text))
WAN     : 50:41:B9:xx:xx:92 (Factory, 0xE006 (hex))
2.4 GHz : 50:41:B9:xx:xx:90 (Factory, 0x4    (hex))
5 GHz   : 50:41:B9:xx:xx:91 (Factory, 0x8004 (hex))

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-25 19:28:54 +02:00
Alan Luck
2c9a07ed28 ramips: add missing information to dlink headers
Add additional header information required for newer
bootloaders found on DIR-2660-A1 & A2.

Also remove the MTD splitter compatible from the second firmware
partition, as OpenWrt only supports handling of the first one.

Signed-off-by: Alan Luck <luckyhome2008@gmail.com>
[rephrase commit message, remove removal of read-only flags]
Signed-off-by: David Bauer <mail@david-bauer.net>
2021-09-24 12:32:28 +02:00
Andrea Poletti
de0c380a5f ramips: add support for Sitecom WLR-4100 v1 002
Sitecom WLR-4100 v1 002 (marked as X4 N300) is a wireless router
Specification:
SoC: MT7620A
RAM: 64 MB DDR2
Flash: MX25L6405D SPI NOR 8 MB
WIFI: 2.4 GHz integrated
Ethernet: 5x 10/100/1000 Mbps QCA8337
USB: 1x 2.0
LEDS: 2x GPIO controlled, 5x switch
Buttons: 1x GPIO controlled
UART: row of 4 unpopulated holes near USB port, starting count from
      white triangle on PCB:

    VCC 3.3V
    GND
    TX
    RX

    baud: 115200, parity: none, flow control: none

Installation

    Connect to one of LAN (yellow) ethernet ports,
    Open router configuration interface,
    Go to Toolbox > Firmware,
    Browse for OpenWrt factory image with dlf extension and hit Apply,
    Wait few minutes, after the Power LED will stop blinking, the router is
    ready for configuration.

Known issues
Some USB 2.0 devices work at full speed mode 1.1 only

MAC addresses

factory partition only contains one (binary) MAC address in 0x4.
u-boot-env contains four (ascii) MAC addresses, of which two appear
to be valid.

  factory     0x4       **:**:**:**:b9:84  binary
  u-boot-env  ethaddr   **:**:**:**:b9:84  ascii
  u-boot-env  wanaddr   **:**:**:**:b9:85  ascii
  u-boot-env  wlanaddr  00:AA:BB:CC:DD:12  ascii
  u-boot-env  iNICaddr  00:AA:BB:CC:DD:22  ascii

The factory firmware only assigns ethaddr. Thus, we take the
binary value which we can use directly in DTS.

Additional information
OEM firmware shell password is: SitecomSenao
useful for creating backup of original firmware.
There is also another revision of this device (v1 001), based on RT3352 SoC

Signed-off-by: Andrea Poletti <polex73@yahoo.it>
[remove config DT label, convert to nvmem, remove MAC address
 setup from u-boot-env, add MAC address info to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-09-05 23:52:35 +02:00
Sungbo Eo
f08b76b32f ramips: w2914ns-v2: consolidate leds nodes into dtsi
w2914ns-v2, 11acnas, and freezio use almost same board and thus share a
common dtsi file. Now that LED labels do not contain "devicename" since
commit c846dd91f0 ("ramips: remove model name from LED labels"), let's
move the leds nodes to dtsi and remove them from dts.

Note that freezio has only one USB 3.0 port and adding &ehci_port2 trigger
does not incur any visible changes.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2021-08-30 00:37:47 +02:00
David Bauer
90e167abaa ramips: add label-mac for TL-MR3020 v3
The TP-Link TL-MR3020 v3 only has a single MAC address assigned for
ethernet LAN as well as WiFi. This MAC address is also printed on the
casing.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-08-28 01:35:02 +02:00
David Bauer
9c965893ed ramips: enable fast-read for TL-MR3020 v3
The GigaDevices GD25Q64B found on the TL-MR3020 v3 supports the fast
read instruction. Add the required DT property in order to enable usage
of this property.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-08-28 01:31:45 +02:00
David Bauer
db3545cd02 ramips: increase SPI frequency for TL-MR3020 v3
The GigaDevices GD25Q64B supports higher SPI clocks than 10 MHz. While
100 MHz do not work reliably, 50 MHz works without issues.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-08-28 01:31:36 +02:00
David Bauer
161ee85bbe ramips: fix input type for TL-MR3020 v3
The modec{1,2} keys are actually switches.

Add the respective DTS properties to avoid accidental activation of
failsafe mode.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-08-28 01:31:29 +02:00
David Yang
38cb500516 ramips: expose ephy leds for miwifi-mini
Give users more control by exposing ephy leds.

Signed-off-by: David Yang <mmyangfl@gmail.com>
[remove execute bit on 01_leds, add status for gpio2]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-08-25 01:42:17 +02:00
David Yang
5ed11012e7 ramips: lock u-boot partition and unlock u-boot-env for miwifi-mini
Generally u-boot should keep read-only to avoid mis-overwriting and
bricking the device, but u-boot-env could be safely modified with u-boot
setenv tool.

Signed-off-by: David Yang <mmyangfl@gmail.com>
2021-08-25 01:42:17 +02:00
David Yang
a6c410ae10 ramips: increase flash freq for miwifi-mini
The flash is Winbond 25Q128. As it has large rom, better to increase flash
frequency to 70MHz according to the flash spec and enable fast-read.

Signed-off-by: David Yang <mmyangfl@gmail.com>
2021-08-25 01:42:17 +02:00
Giovanni Cascione
d57ba86e48 ramips: add support for D-Link DAP-1325-A1
This patch adds support for D-Link DAP-1325-A1 (Range Extender Wi-Fi N300)

Specifications:
- SoC: 580Mhz MT7628NN
- RAM: 64MB, DDR2 SDRAM
- Storage: 8MB, SPI (W25Q64JVSSIQ)
- Ethernet: 1x 10/100 LAN port
- WIFI: 2.4 GHz 802.11bgn
- LED: Status (2x to provide 3 colors), Wi-Fi Signal Strength (4x)
- Buttons: Reset, WPS
- UART: Serial console (57600, 8n1)
Row of 4 holes near LAN port, starting from square hole:
3.3V, TX,RX,GND
- FCC ID: fccid.io/KA2AP1325A1/

Installation:

Failsafe UI
Firmware can be uploaded with Failsafe UI web page:
- turn device off
- press and hold reset button
- turn device on
- keep holding reset until red wifi strength led turns on (ab. 10sec)
- connect to device through LAN port
PC must be configured with static ip (192.168.0.x)
- connect to 192.168.0.50
- select image to be flashed and upload.
Device will reboot after successful update

Serial port/TFTP server
- Connect through serial connectors on PCB (e.g. with teraterm)
- Set up a TFTP server, and connect through LAN with static IP
- Put image file in the root of the server
- Boot the device and select '2' at U-Boot startup
- Set device IP, server IP and image file name
- Start upload and flash

Signed-off-by: Giovanni Cascione <ing.cascione@gmail.com>
[fix whitespaces in DTS, convert to nvmem, add mtd-eeprom]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-08-25 01:42:17 +02:00
Shiji Yang
a73a8269e1 ramips: add support for DomyWifi DM202/DM203/DW22D
Specifications:
* SOC: MT7620A + MT7610E
* ROM: 16 MiB spi flash (W25Q128FVSG)
* RAM: 128 MiB DDR2 (W971GG6KB-25)
* WAN: 10/100M *1
* LAN: 10/100M *4
* USB: Type-A USB2.0 *1
* SD: MicroSD *1
* Button: Reset *1
* Antennas: 2.4 GHz *2 + 5 GHz *1
* TTL Baudrate: 57600
* U-Boot Recovery: IP: 10.10.10.123, Server: 10.10.10.3

Installation:
* Web UI Update
  1. Open http://192.168.10.1/upgrade.html in the browser.
  2. Rename firmware to a short name like firmware.bin and then upload it.
  3. Fill in the password column with the following content:
  password | mtd -x mIp2osnRG3qZGdIlQPh1 -r write /tmp/firmware.bin firmware
* TFTP + U-Boot
  1. Connect device with a TTL cable.
  2. Press "2" when booting to select "Load system code then write to Flash via TFTP".
  3. Upload firmware by tftpd64, it will boot when write instruction is executed.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2021-08-25 01:42:16 +02:00
Shiji Yang
09143282bd ramips: add support for Motorola MWR03
Specifications:
* SOC: MT7628AN + MT7612E
* ROM: 8 MiB Flash
* RAM: 64 MiB DDR2
* WAN: 10/100M *1
* LAN: 10/100M *3
* Button: Reset *1
* LEDs: orange *1, white *1
* Antennas: 2.4 GHz *2 + 5 GHz *2
* TTL Baudrate: 57600
* TFTP Upgrade: IP: 192.168.51.1, Server: 192.168.51.100

MAC addresses as verified by OEM firmware:

use   address   source
2g    *:d8      factory 0x0004 (label)
5g    *:d9      factory 0x8004
LAN   *:d7      factory $label -1
WAN   *:da      factory $label +2

Installation (TFTP + U-Boot):
 * Connect device with a TTL cable and open a serial session by
   PuTTY.
 * Press "2" when booting to select "Load system code then write
   to Flash via TFTP".
 * Configure the IP of local host server.
 * Upload firmware by tftpd64, it will boot when write instruction
   is executed.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[fix DTS line endings, fix label MAC address, adjust status LED
 names, convert mtd-mac-address-increment to mac-address-increment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-08-25 01:41:35 +02:00
Shiji Yang
80e70be0ab ramips: add new flash layout support to Phicomm K2
Descriptions:
Phicomm K2 (PSG1218) got a new "permanent_config" partition after
update firmware to v22.5. This partition located in front of the
firmware partition, same as The Phicomm K2P and K2G. Due to this
change the new bootloader can't load previous firmware any more.
This commit is aimed at add support for Phicomm K2 which official
firmware version is 22.5.x or newer. For which runs old firmware
version, just update OpenWrt that has a prefix of "k2-v22.4".
For uniform naming, this commit also changed the model name
PSG1218 to a more recognizable name K2, refer to Phicomm K2G,
K2P K2T.

OpenWrt selection table:
official firmware version           OpenWrt
v22.4.x.x or older              phicomm_k2-v22.4
v22.5.x.x or newer              phicomm_k2-v22.5

Installation:
Same as Phicomm K2G, K2P, PSG1208.
a. TFTP + U-Boot
b. Open telnet by some web page vulnerability (Search Baidu by key
   words "K2 telnet"), and then we can upload firmware image to
   /tmp and write it to firmware partition with mtd instruction.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[rebase, add/harmonize version in model variables, fix version typo
 in commit message, wrap commit message properly]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-08-24 20:26:00 +02:00
Adrian Schmutzler
c4143505e0 ramips: mt7620: move Phicomm MAC address setup to DTSI
The setup is the same for all devices, so move it up one level.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-08-24 20:26:00 +02:00
Michael Siegenthaler
4b4fa2f9fe ramips: fix ethernet MAC address on Omega2
According to https://docs.onion.io/omega2-docs/mac-address.html, 0x28 is
the correct location to read the address on Onion Omega 2(+) devices.

This fixes a regression introduced by commit 77e850fe76 ("ramips: tidy up
MAC address setup for Linkit Smart and Omega2"), which was a cleanup that
intended to preserve existing behavior. In my testing with v19.07.7,
however, the MAC address determined from the device tree takes precedence
over the one set by 02_network, so the aforementioned commit actually
changed the behavior.

Signed-off-by: Michael Siegenthaler <msiegen@google.com>
[Adapt patch to nvmem usage]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-08-21 16:30:30 +02:00
Adrian Schmutzler
8a78d61299 ramips: convert mtd-mac-address to nvmem for UniElec devices
Convert this series by moving the definitions to the individual
devices.

Now all devices on ramips are converted.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-08-20 18:13:55 +02:00
Adrian Schmutzler
f13c7a56f0 ramips: remove redundant nvmem definitions
Due to use of a script when migrating from mtd-mac-address, a few
of the definitions are redundant in DTSI and DTS files. Remove
those.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-08-20 18:13:50 +02:00
Adrian Schmutzler
9cb5853592 ramips: fix indent in DTS for GL.iNet VIXMINI/microuter-N300
Use correct indent.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-08-20 18:10:48 +02:00
Adrian Schmutzler
7f1b0f68f1 ramips: convert mtd-mac-address to nvmem for D-Link DIR-8xx
Convert this series by moving the definitions to the individual
devices.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-08-20 18:10:48 +02:00
Adrian Schmutzler
ba3d92c5a0 ramips: convert most mtd-mac-address cases in DTSI to nvmem
Convert most of the cases from mtd-mac-address to nvmem where
MAC addresses are set in the DTSI, but the partitions are only
located in the device DTS. This posed some problems earlier, since
in these cases we are using partitions before they are defined,
and the nvmem system did not seem to like that.

There have been a few different resolution approaches, based on
the different tradeoffs of deduplication vs. maintainability:

 1. In many cases, the partition tables were identical except for
    the firmware partition size, and the firmware partition was
    the last in the table.
    In these cases, the partition table has been moved to the
    DTSI, and only the firmware partition's "reg" property has
    been kept in the DTS files. So, the updated nvmem definition
    could stay in the DTSI files as well.

 2. For all other cases, splitting up the partition table would
    have introduced additional complexity. Thus, the nodes to be
    converted to nvmem have been moved to the DTS files where the
    partitioning was defined.

 3. For Netgear EX2700 and WN3000RP v3, the remaining DTSI file
    was completely dissolved, as it was quite small and the name
    was not really nice either.

 4. The D-Link DIR-853 A3 was converted to nvmem as well, though
    it is just a plain DTS file not taken care of in the first
    wave.

In addition, some minor rearrangements have been made for tidyness.

Not covered (yet) by this patch are:

 * Various unielec devices
 * The D-Link DIR-8xx family

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-08-18 23:46:02 +02:00
David Yang
efca67983d ramips: add WPS button for newifi d1
This device has a WPS button under WiFi antenna cover, add it to dts.

Signed-off-by: David Yang <mmyangfl@gmail.com>
2021-08-17 18:41:17 +02:00
Adrian Schmutzler
ad6b077049 ramips: mt7628: move mtd-eeprom out of root DTSI
The mt76x8 subtarget is the only one in ramips that stores the
mediatek,mtd-eeprom property directly in the "root" mt7628an.dtsi.

This is not optimal for a few different reasons:

 * If you don't really know it or are used to other (sub)targets,
   the property will be set somewhat magically.
 * The property is set based on &factory partition before (if at all)
   this partition is defined.
 * There are several devices that have different offset or even
   different partitions to read from, which will then be overwritten
   in the DTS files. Thus, definitions are scattered between root
   DTSI and individual files.

Based on these circumstances, the "root" definition is removed and
the property is added to the device-based DTS(I) files where needed
and applicable. This should be easier to grasp for unexperienced
developers and will move the property closer to the partition
definitions.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-08-17 18:41:17 +02:00
Fabian Bläse
c36e9f891b ramips: add missing label-mac-device for Xiaomi Mi Router 4A (100M)
As both the Mi Router 4A (100M) and the Mi Router 4C use the same
label-mac-device, the alias can be moved to the shared dtsi.

Signed-off-by: Fabian Bläse <fabian@blaese.de>
2021-08-05 22:55:39 +02:00
Ansuel Smith
06bb4a5018 ramips: convert mtd-mac-address to nvmem implementation
Define nvmem-cells and convert mtd-mac-address to nvmem implementation.
The conversion is done with an automated script.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2021-07-19 14:51:22 +02:00
Ansuel Smith
d284e6ef0f treewide: convert mtd-mac-address-increment* to generic implementation
Rework patch 681-NET-add-mtd-mac-address-support to implement
only the function to read the mac-address from mtd.
Generalize mtd-mac-address-increment function so it can be applied
to any source of of_get_mac_address.
Rename any mtd-mac-address-increment to mac-address-increment.
Rename any mtd-mac-address-increment-byte to mac-address-increment-byte.

This should make simplify the conversion of target to nvmem implementation.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2021-07-19 14:51:22 +02:00
Karim Dehouche
6639623e75 ramips: add support for D-Link DIR-853 A3
Specifications:
* SoC: MT7621AT
* RAM: 256MB
* Flash: 128MB NAND flash
* WiFi: MT7615DN (2.4GHz+5Ghz) with DBDC
* LAN: 5x1000M
* Firmware layout is Uboot with extra 96 bytes in header
* Base PCB is DIR-1360 REV1.0
* LEDs Power Blue+Orange,Wan Blue+Orange,WPS Blue,"2.4G"Blue, "5G" Blue,
  USB Blue
* Buttons Reset,WPS, Wifi

MAC addresses on OEM firmware:

lan      factory 0xe000   f4:*:*:a8:*:65  (label)
wan      factory 0xe006   f4:*:*:a8:*:68
2.4 GHz  [not on flash]   f6:*:*:c8:*:66
5.0 GHz  factory 0x4      f4:*:*:a8:*:66

The increment of the 4th byte for the 2.4g address appears to vary.
Reported cases:

       5g                 2.4g         increment
 f4:XX:XX:a8:XX:66  f6:XX:XX:c8:XX:66  +0x20
 x0:xx:xx:68:xx:xx  x2:xx:xx:48:xx:xx  -0x20
 x4:xx:xx:6a:xx:xx  x6:xx:xx:4a:xx:xx  -0x20

Since increment is inconsistent and there is no obvious pattern
in swapping bytes, and the 2.4g address has local bit set anyway,
it seems safer to use the LAN address with flipped byte here in
order to prevent collisions between OpenWrt devices and OEM devices
for this interface. This way we at least use an address as base
that is definitely owned by the device at hand.

Flashing instruction:

The Dlink "Emergency Room" cannot be accessed through the reset
button on this device. You can either use console or use the
encrypted factory image availble in the openwrt forum.

Once the encrypted image is flashed throuh the stock Dlink web
interface, the sysupgrade images can be used.

Header pins needs to be soldered near the WPS and Wifi buttons.

The layout for the pins is (VCC,RX,TX,GND). No need to connect the VCC.

the settings are:

Bps/Par/Bits          : 57600 8N1
Hardware Flow Control : No
Software Flow Control : No

Connect your client computer to LAN1 of the device
Set your client IP address manually to 192.168.0.101 / 255.255.255.0.
Call the recovery page or tftp for the device at http://192.168.0.1
Use the provided emergency web GUI to upload and flash a new firmware to
the device

At the time of adding support the wireless config needs to be set up by
editing the wireless config file:

 * Setting the country code is mandatory, otherwise the router loses
   connectivity at the next reboot. This is mandatory and can be done
   from luci. After setting the country code the router boots correctly.
   A reset with the reset button will fix the issue and the user has to
   reconfigure.

 * This is minor since the 5g interface does not come up online although
   it is not set as disabled. 2 options here:

   1- Either run the "wifi" command. Can be added from LUCI in system -
      startup - local startup and just add wifi above "exit 0".

   2- Or add the serialize option in the wireless config file as shown
      below. This one would work and bring both interfaces automatically
      at every boot:

      config wifi-device 'radio0'
          option serialize '1'

      config wifi-device 'radio1'
          option serialize '1'

Signed-off-by: Karim Dehouche <karimdplay@gmail.com>
[rebase, improve MAC table, update wireless config comment, fix
 2.4g macaddr setup]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-07-12 00:19:14 +02:00
Tee Hao Wei
0c721434ea ramips: add support for Linksys EA8100 v2
Specifications:
- SoC: MT7621AT
- RAM: 256MB
- Flash: 128MB NAND
- Ethernet: 5 Gigabit ports
- WiFi: 2.4G/5G MT7615N
- USB: 1 USB 3.0, 1 USB 2.0

This device is very similar to the EA7300 v1/v2, EA7500 v2, and EA8100 v1.

Installation:

Upload the generated factory image through the factory web interface.

(following part taken from EA7300 v2 commit message:)

This might fail due to the A/B nature of this device. When flashing, OEM
firmware writes over the non-booted partition. If booted from 'A',
flashing over 'B' won't work. To get around this, you should flash the
OEM image over itself. This will then boot the router from 'B' and
allow you to flash OpenWRT without problems.

Reverting to factory firmware:

Hard-reset the router three times to force it to boot from 'B.' This is
where the stock firmware resides. To remove any traces of OpenWRT from
your router simply flash the OEM image at this point.

With thanks to Tom Wizetek (@wizetek) for testing.

Signed-off-by: Tee Hao Wei <angelsl@in04.sg>
2021-07-11 16:58:12 +02:00
Adrian Schmutzler
5e8eaac8c3 ramips: mt7628an: remove redundant console setup for bootargs
This is already set in mt7628an.dtsi

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-07-10 20:35:11 +02:00
Stas Fiduchi
b8168f4716 ramips: add support for D-Link DIR-853-R1
This PR adds support for router D-Link DIR-853-R1

Specifications:

    SoC: MT7621AT
    RAM: 128MB
    Flash: 16MB SPI
    WiFi: MT7615DN (2.4GHz+5Ghz) with DBDC (This mode allows this
      single chip act as an 2x2 11n radio and an 2x2 11ac radio at the
      same time)
    LAN: 5x1000M
    LEDs Power Blue+Orange,Wan Blue+Orange,WPS Blue,"2.4G"Blue, "5G" Blue
    USB Blue
    Buttons Reset,WPS, Wifi

MAC addresses:

|Interface   |        MAC      |    Factory  |Comment
|------------|-----------------|-------------|----------------
|WAN sticker |C4:XX:XX:6E:XX:2A|             |Sticker
|LAN         |C4:XX:XX:6E:XX:2B|             |
|Wifi (5g)   |C4:XX:XX:6E:XX:2C|0x4          |
|Wifi (2.4g) |C6:XX:XX:7E:XX:2C|             |
|            |                 |             |
|            |C4:XX:XX:6E:XX:2E|0x8004 0xe000|
|            |C4:XX:XX:6E:XX:2F|0xe006       |

The increment of the 4th byte for the 2.4g address appears to vary.
Reported cases:

       5g                 2.4g         increment
 C4:XX:XX:6E:XX:2C  C6:XX:XX:7E:XX:2C  0x10
 f4:XX:XX:16:XX:32  f6:XX:XX:36:XX:32  0x20
 F4:XX:XX:A6:XX:E3  F6:XX:XX:B6:XX:E3  0x10

Since increment is inconsistent and there is no obvious pattern
in swapping bytes, and the 2.4g address has local bit set anyway,
it seems safer to use the LAN address with flipped byte here in
order to prevent collisions between OpenWrt devices and OEM devices
for this interface. This way we at least use an address as base
that is definitely owned by the device at hand.

Flashing instruction:

The Dlink "Emergency Room"

Connect your client computer to LAN1 of the device
Set your client IP address manually to 192.168.0.101 / 255.255.255.0.
Then, power down the router, press and hold the reset button, then
re-plug it. Keep the reset button pressed until the internet LED stops
flashing
Call the recovery page or tftp for the device at http://192.168.0.1
Use the provided emergency web GUI to upload and flash a new firmware to
the device.

Signed-off-by: Stas Fiduchi <fiduchi@protonmail.com>
[commit title/message improvements, use correct label MAC address,
 calculate MAC addresses based on 0x4, minor DTS style fixes, add
 uart2 to state_default, remove factory image, add 2.4g MAC address,
 use partition DTSI, add macaddr comment in DTS]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-07-10 20:01:29 +02:00
Alexander Couzens
8d497b6570
ramips: add support for minew g1-c
The minew g1-c is a smart home gateway / BLE gateway.
A Nordic nRF52832 is available via USB UART (cp210x) to support BLE.
The LED ring is a ring of 24x ws2812b connect to a generic GPIO (unsupported).
There is a small LED which is only visible when the device is open which
will be used as LED until the ws2812b is supported.
The board has also a micro sdcard/tfcard slot (untested).
The Nordic nRF52832 exposes SWD over a 5pin header (GND, VCC, SWD, SWC, RST).
The vendor uses an older OpenWrt version, sysupgrade can be used via
serial or ssh.

CPU:		MT7628AN / 580MHz
RAM:		DDR2 128 MiB RAM
Flash:		SPI NOR 16 MiB W25Q128
Ethernet:	1x 100 mbit (Port 0) (PoE in)
USB:		USB hub, 2x external, 1x internal to USB UART
Power:		via micro usb or PoE 802.11af
UART:		3.3V, 115200 8n1

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2021-07-05 17:27:13 +02:00
David Bauer
51b61fd570 ramips: add support for Tenbay T-MB5EU-V01
Hardware
--------
MediaTek MT7621 SoC
256M DDR3
16MB BoHong SPI-NOR
MediaTek MT7905+7975 2x2T2R DBDC bgnax / acax
RGB LED
WPS + RESET Button
UART on compute module (silkscreened / 115200n8)

The router itself is just a board with Power / USB / RJ-45 connectors
and DC/DC converters. The SoC and WiFi components are on a
daughterboard which connect using two M.2 connectors.

The compute module has the model number "T-CB1800K-DM2 V02" printed on
it. The main baord has "T-MB5EU V01" printed on it. This information
might be useful, as it's highly likely either of these two will be
reused in similar designs.

The router itself is sold as Tenbay T-MB5EU directly from the OEM as
well as "KuWFI AX1800 Smart WiFi 6 Eouter" on Amazon.de for ~50€ in a
slightly different case.

Installation
------------

A Tool for creating a factory image for the Vendor Web Interface can be
found here: https://github.com/blocktrron/t-mb5eu-v01-factory-creator/

As the OEM Firmware is just a modified LEDE 17.01, you can also access
failsafe mode via UART while the OS boots, by connecting to UART
and pressing "f" when prompted. The Router is reachable at
192.168.1.1 via root without password.

Transfer the OpenWrt sysupgrade image via scp and apply with sysupgrade
using the -n and -F flags.

Alternatively, the board can be flashed by attaching to the UART
console, interrupting the boot process by keeping "0" pressed while
attaching power.

Serve the OpenWrt initramfs using a TFTP server with address
192.168.1.66. Rename the initramfs to ax1800.bin.

Attach your TFTP server to one of the LAN ports. Execute the following
commands.

 $ setenv ipaddr 192.168.1.67
 $ setenv serverip 192.168.1.66
 $ tftpboot 0x84000000 ax1800.bin
 $ bootm

Wait for the device to boot. Then transfer the OpenWrt sysupgrade image
to the device using SCP and apply sysupgrade.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-06-27 21:40:27 +02:00
Alexander Couzens
60fadae62b ramips: ethernet: ralink: move reset of the esw into the esw instead of fe
The esw reset should only done by the esw driver and not by the fe itself.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2021-06-25 10:52:50 +02:00
Alexander Couzens
694561ae60 ramips: ethernet: ralink: use the reset controller api for esw & ephy
Instead of writing direct into the reset registers.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2021-06-25 10:52:50 +02:00
Liu Yu
e6b3e77e6e ramips: fix software reboot failure on HILINK HLK-7628N
In the new kernel version 5.X,reboot will fail.

When SOC is reset, flash has not exited the 4-byte address mode,
which causes the operation mode mismatch of flash during boot.Add
broken-flash-reset to make flash exit 4-byte address mode before
SOC reset

Signed-off-by: Liu Yu <f78fk@live.com>
2021-06-23 14:22:19 +08:00
Shiji Yang
b843540057 ramips: add missing "pinctrl-names" for Youku YK1
Without this definition ethernet led can work as usual, but it's better to
re-add it. Relying on default values may cause uncontrollable factors.

Fixes: 882a6116d3 ("ramips: improve pinctrl for Youku YK-L1")

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2021-06-23 14:22:19 +08:00
Michael Pratt
6972e498d3 ramips: mt7620: move mt7620_mdio_mode() to ethernet driver
The function mt7620_mdio_mode is only called once
and both the function and mdio_mode block have been named incorrectly,
leading to confusion and useless commits.

These lines in the mdio_mode block of mt7620_hw_init
are only intended for boards with an external mt7530 switch.
(see commit 194ca6127e)

Therefore, move lines from mdio_mode to the place in soc_mt7620.c
where the type of mt7530 switch is identified,
and move lines from mt7620_mdio_mode to a main function.

mt7620_mdio_mode was called from mt7620_gsw_init
where the priv struct is available,
so the lines must stay in mt7620_gsw_init function.

In order to keep things as simple as possible,
keep the DTS property related function calls together,
by moving them from mt7620_gsw_probe to init.

Remove the now useless DTS properties and extra phy nodes.

Fixes: 5a6229a93d ("ramips: remove superfluous & confusing DT binding")
Fixes: b85fe43ec8 ("ramips: mt7620: add force use of mdio-mode")
Signed-off-by: Michael Pratt <mcpratt@pm.me>
2021-06-23 14:22:18 +08:00
Michael Pratt
0976b6c426 ramips: mt7620: use DTS to set PHY base address for external PHYs
Set the PHY base address to 12 for mt7530 and 8 for others,
which is based on the default setting for some devices
from printing the register with the following command
after it is written to by uboot during the boot cycle.

`md 0x10117014 1`

PHY_BASE option only uses 5 bits of the register,
bits 16 to 20, so use 8-bit integer type.

Set the option using the DTS property mediatek,ephy-base
and create the gsw node if missing.

Also, added a kernel message to display the EPHY base address.

Note:
If anything is written to a PHY address that is greater than 1 hex char (greater than 0xf)
then there is adverse effects with Atheros switches.

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2021-06-23 14:22:18 +08:00
Michael Pratt
a2acdf9607 ramips: mt7620: remove useless GMAC nodes
These nodes are used for configuring a GMAC interface
and for defining external PHYs to be accessed with MDIO.

None of this is possible on MT7620N, only MT7620A,
so remove them from all MT7620N DTS.

When the mdio-bus node is missing, the driver returns -NODEV
which causes the internal switch to not initialize.
Replace that return so that everything works without the DTS node.

Also, an extra kernel message to indicate for all error conditions
that mdio-bus is disabled.

Fixes: d482356322 ("ramips: mt7620n: add mdio node and disable port4 by default")
Fixes: aa5014dd1a ("ramips: mt7620n: enable port 4 as EPHY by default")
Signed-off-by: Michael Pratt <mcpratt@pm.me>
2021-06-23 14:22:18 +08:00
Michael Pratt
953bfe2eb3 ramips: mt7620: simplify DTS properties for GMAC
There are only 2 options in the driver
for the function of mt7620 internal switch port 4:

  EPHY mode (RJ-45, internal PHY)
  GMAC mode (RGMII, external PHY)

Let the DTS property be boolean instead of string
where EPHY mode is the default.

Fix how the properties are written
for all DTS that use them,
and add missing nodes where applicable,
and remove useless nodes,
and minor DTS formatting.

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2021-06-23 14:22:18 +08:00
Adrian Schmutzler
2001c0ca9f ramips: reorganize DTSI files for D-Link DIR-8xx
* Remove micro-DTSI mt7621_dlink_dir-882-x1.dtsi to ease reading
   config without too much inheritance
 * Use "separate" partitioning DTSIs so we can use the partitioning
   without a complete match on the other settings (i.e. without the
   former parent DTSI)
 * Rename files to express the new organization

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-06-20 17:29:52 +02:00
Amish Vishwakarma
d22fb7f4fd ramips: add support for TP-Link Archer C6 v3
The patch adds support for the TP-Link Archer C6 v3 (FCC ID TE7A6V3)
The patch adds identification changes to the existing TP-Link Archer A6,
by Vinay Patil <post2vinay@gmail.com>, which has identical hardware.

Specification
-------------
MediaTek MT7621 SOC
RAM:         128MB DDR3
SPI Flash:   W25Q128 (16MB)
Ethernet:    MT7530 5x 1000Base-T
WiFi 5GHz:   Mediatek MT7613BE
WiFi 2.4GHz: Mediatek MT7603E
UART/Serial: 115200 8n1

Device Configuration & Serial Port Pins
---------------------------------------
ETH Ports:    LAN4 LAN3 LAN2 LAN1 WAN
             _______________________
             |                     |
Serial Pins: |   VCC GND TXD RXD   |
             |_____________________|

LEDs:         Power Wifi2G Wifi5G LAN WAN

Build Output
------------
The build will generate following set of files
[1] openwrt-ramips-mt7621-tplink_archer-c6-v3-initramfs-kernel.bin
[2] openwrt-ramips-mt7621-tplink_archer-c6-v3-squashfs-factory.bin
[3] openwrt-ramips-mt7621-tplink_archer-c6-v3-squashfs-sysupgrade.bin

How to Use - Flashing from TP-Link Web Interface
------------------------------------------------
* Go to "Advanced/System Tools/Firmware Update".
* Click "Browse" and upload the OpenWrt factory image: factory.bin[2]
* Click the "Upgrade" button, and select "Yes" when prompted.

TFTP Booting
------------
Setup a TFTP boot server with address 192.168.0.5.
While starting U-boot press '4' key to stop autoboot.
Copy the initramfs-kernel.bin[1] to TFTP server folder, rename as test.bin
From u-boot command prompt run tftpboot followed by bootm.

Recovery
--------
Archer A6 V3 has recovery page activated if SPI booting from flash fails.
Recovery page can be activated by powercycling the router four times
before the boot process is complete.
Note: TFTP boot can be activated only from u-boot serial console.
Device recovery address: 192.168.0.1

Signed-off-by: Amish Vishwakarma <vishwakarma.amish@gmail.com>
[fix indent]
Signed-off-by: David Bauer <mail@david-bauer.net>
2021-06-13 11:32:31 +02:00
Adam Elyas
edaf432bf4 ramips: fix LAN LED trigger assignment for Xiaomi Router 3 Pro
The default trigger for the amber lights on lan1 and lan3 were
mistakenly swapped after the device's migration to DSA. This
caused activity on one port to trigger the amber light on the
other port. Swapping their default trigger in the DTS file
fixes that.

Signed-off-by: Adam Elyas <adamelyas@outlook.com>
[minor commit title adjustment, wrap commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-06-09 22:44:00 +02:00
Liu Yu
ae9c5cd37b ramips: fix Ethernet random MAC address for HILINK HLK-7628N
Set the ethernet address from flash.

MAC addresses as verified by OEM firmware:

  use   interface  source
  2g    wlan0      factory 0x04 (label)
  LAN   eth0.1     factory 0x28 (label+1)
  WAN   eth0.2     factory 0x2e (label+2)

Fixes: 671c9d16e3 ("ramips: add support for HILINK HLK-7628N")

Signed-off-by: Liu Yu <f78fk@live.com>
[drop old MAC address setup from 02_network, cut out state_default
changes, face-lift commit message, add Fixes:]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-06-09 22:18:37 +02:00
Andreas Böhler
a3d8c1295e ramips: Add support for SERCOMM NA502
The SERCOMM NA502 is a smart home gateway manufactured by SERCOMM and sold
under different brands (among others, A1 Telekom Austria SmartHome
Gateway). It has multi-protocol radio support in addition to LAN and WiFi.

Note: BLE is currently unsupported.

Specifications
--------------

  - MT7621ST 880MHz, Single-Core, Dual-Thread
  - MT7603EN 2.4GHz WiFi
  - MT7662EN 5GHz WiFi + BLE
  - 128MiB NAND
  - 256MiB DDR3 RAM
  - SD3503 ZWave Controller
  - EM357 Zigbee Coordinator

MAC address assignment
----------------------

LAN MAC is read from the config partition, WiFi 2.4GHz is LAN+2 and matches
the OEM firmware. WiFi 5GHz with LAN+1 is an educated guess since the
OEM firmware does not enable 5GHz WiFi.

Installation
------------
Attach serial console, then boot the initramfs image via TFTP.
Once inside OpenWrt, run sysupgrade -n with the sysupgrade file.

Attention: The device has a dual-firmware design. We overwrite kernel2,
since kernel1 contains an automatic recovery image.

If you get NAND ECC errors and are stuck with bad eraseblocks, try to
erase the mtd partition first with

mtd unlock ubi
mtd erase ubi

This should only be needed once.

Signed-off-by: Andreas Böhler <dev@aboehler.at>
[use kiB for IMAGE_SIZE]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-06-06 21:00:09 +02:00
Ben Gainey
a509b80065 ramips: add support for the Wavlink WL-WN579X3
About the device
----------------

SoC: MediaTek MT7620a @ 580MHz
RAM: 64M
FLASH: 8MB
WiFi: SoC-integrated: MediaTek MT7620a bgn
WiFi: MediaTek MT7612EN nac
GbE: 2x (RTL8211F)
BTN: - WPS
- Reset
- Router/Repeater/AP (3-way slide-switch)
LED: - WPS (blue)
- 3-segment Wifi signal representation (blue)
- WiFi (blue)
- WAN (blue)
- LAN (blue)
- Power (blue)
UART: UART is present as Pads with through-holes on the PCB. They are
located next to the reset button and are labelled Vcc/TX/RX/GND as
appropriate. Use 3.3V, 57600-8N1.

Installation
------------

Using the webcmd interface
--------------------------

Warning: Do not update to the latest Wavlink firmware (version
20201201) as this removes the webcmd console and you will need to
use the serial port instead.

You will need to have built uboot/sqauashfs image for this device,
and you will need to provide an HTTP service where the image can
be downloaded from that is accessible by the device.
You cannot use the device manufacturers firmware upgrade interface
as it rejects the OpenWrt image.

1. Log into the device's admin portal. This is necessary to
   authenticate you as a user in order to be able to access the
   webcmd interface.
2. Navigate to http://<device-ip>/webcmd.shtml - you can access
   the console directly through this page, or you may wish to
   launch the installed `telnetd` and use telnet instead.
   * Using telnet is recommended since it provides a more
     convenient shell interface that the web form.
   * Launch telnetd from the form with the command `telnetd`.
   * Check the port that telnetd is running on using
     `netstat -antp|grep telnetd`, it is likely to be 2323.
   * Connect to the target using `telnet`. The username should
     be `admin2860`, and the password is your admin password.
3. On the target use `curl` to download the image.
   e.g.  `curl -L -O http://<some-other-lan-ip>/openwrt-ramips-mt7620-\
          wavlink_wl-wn579x3-squashfs-sysupgrade.bin`.
   Check the hash using `md5sum`.
4. Use the mtd_write command to flash the image.
   * The flash partition should be mtd4, but check
     /sys/class/mtd/mtd4/name first. The partition should be
     called 'Kernel'.
   * To flash use the following command:
     `mtd_write -r -e /dev/mtd<n> write <image-file> /dev/mtd<n>`
     Where mtd<n> is the Kernel partition, and <image-file> is
     the OpenWrt image previously downloaded.
   * The command above will erase, flash and then reboot the
     device. Once it reboots it will be running OpenWrt.

Connect via ssh to the device at 192.168.1.1 on the LAN port.
The WAN port will be configured via DHCP.

Using the serial port
---------------------

The device uses uboot like many other MT7260a based boards. To
use this interface, you will need to connect to the serial
interface, and provide a TFTP server. At boot follow the
bootloader menu and select option 2 to erase/flash the image.
Provide the address and filename details for the tftp server.
The bootloader will do the rest.

Once the image is flashed, the board will boot into OpenWrt. The
console is available over the serial port.

Signed-off-by: Ben Gainey <ba.gainey@googlemail.com>
2021-06-06 18:56:45 +02:00
Shiji Yang
4a9f389ed2 ramips: split Youku YK1 to YK-L1 and YK-L1c
Device specifications:
* Model: Youku YK-L1/L1c
* CPU: MT7620A
* RAM: 128 MiB
* Flash: 32 MiB (YK-L1)/ 16 MiB (YK-L1c)
* LAN: 2* 10M/100M Ports
* WAN: 1* 10M/100M Port
* USB: 1* USB2.0
* SD: 1* MicroSD socket
* UART: 1* TTL, Baudrate 57600

Descriptions:
  Previous supported device YOUKU yk1 is actually Youku YK-L1. Though they look
  really different, the only hardware difference between the two models is flash
  size, YK-L1 has 32 MiB flash but YK-L1c has 16MiB. It seems that YK-L1c can
  compatible with YK-L1's firmware but it's better to split it to different models.

  It is easy to identify the models by looking at the label on the bottom of the
  device. The label has the model number "YK-L1" or "YK-L1c". Due to different flash
  sizes, YK-L1c that using previous YK-L1's firmware needs to apply "force update"
  to install compatible firmware, so please backup config file before system upgrade.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[use more specific name for DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-06-05 23:39:14 +02:00
Tee Hao Wei
b232680f84 ramips: add support for Linksys EA8100 v1
Specifications:
- SoC: MT7621AT
- RAM: 256MB
- Flash: 128MB NAND
- Ethernet: 5 Gigabit ports
- WiFi: 2.4G/5G MT7615N
- USB: 1 USB 3.0, 1 USB 2.0

This device is very similar to the EA7300 v1/v2 and EA7500 v2.

Installation:

Upload the generated factory image through the factory web interface.

(following part taken from EA7300 v2 commit message:)

This might fail due to the A/B nature of this device. When flashing, OEM
firmware writes over the non-booted partition. If booted from 'A',
flashing over 'B' won't work. To get around this, you should flash the
OEM image over itself. This will then boot the router from 'B' and
allow you to flash OpenWRT without problems.

Reverting to factory firmware:

Hard-reset the router three times to force it to boot from 'B.' This is
where the stock firmware resides. To remove any traces of OpenWRT from
your router simply flash the OEM image at this point.

With thanks to Leon Poon (@LeonPoon) for the initial bringup.

Signed-off-by: Tee Hao Wei <angelsl@in04.sg>
[add missing entry in 10_fix_wifi_mac]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-06-05 23:39:14 +02:00
Jonathan Sturges
6d23e474ad ramips: add support for Amped Wireless ALLY router and extender
Amped Wireless ALLY is a whole-home WiFi kit, with a router (model
ALLY-R1900K) and an Extender (model ALLY-00X19K).  Both are devices are
11ac and based on MediaTek MT7621AT and MT7615N chips.  The units are
nearly identical, except the Extender lacks a USB port and has a single
Ethernet port.

Specification:
- SoC: MediaTek MT7621AT (2C/4T) @ 880MHz
- RAM: 128MB DDR3 (Nanya NT5CC64M16GP-DI)
- FLASH: 128MB NAND (Winbond W29N01GVSIAA)
- WiFi: 2.4/5 GHz 4T4R
  - 2.4GHz MediaTek MT7615N bgn
  - 5GHz MediaTek MT7615N nac
- Switch: SoC integrated Gigabit Switch
- USB: 1x USB3 (Router only)
- BTN: Reset, WPS
- LED: single RGB
- UART:  through-hole on PCB.
   J1: pin1 (square pad, towards rear)=3.3V, pin2=RX,
   pin3=GND, pin4=TX.  Settings: 57600/8N1.

Note regarding dual system partitions
-------------------------------------

The vendor firmware and boot loader use a dual partition scheme.  The boot
partition is decided by the bootImage U-boot environment variable: 0 for
the 1st partition, 1 for the 2nd.

OpenWrt does not support this scheme and will always use the first OS
partition.  It will set bootImage to 0 during installation, making sure
the first partition is selected by the boot loader.

Also, because we can't be sure which partition is active to begin with, a
2-step flash process is used.  We first flash an initramfs image, then
follow with a regular sysupgrade.

Installation:

Router (ALLY-R1900K)
1) Install the flashable initramfs image via the OEM web-interface.
  (Alternatively, you can use the TFTP recovery method below.)
  You can use WiFi or Ethernet.
  The direct URL is:  http://192.168.3.1/07_06_00_firmware.html
  a. No login is needed, and you'll be in their setup wizard.
  b. You might get a warning about not being connected to the Internet.
  c. Towards the bottom of the page will be a section entitled "Or
  Manually Upgrade Firmware from a File:" where you can manually choose
  and upload a firmware file.
  d: Click "Choose File", select the OpenWRT "initramfs" image and click
  "Upload."
2) The Router will flash the OpenWrt initramfs image and reboot.  After
  booting, LuCI will be available on 192.168.1.1.
3) Log into LuCI as root; there is no password.
4) Optional (but recommended) is to backup the OEM firmware before
  continuing; see process below.
5) Complete the Installation by flashing a full OpenWRT image.  Note:
  you may use the sysupgrade command line tool in lieu of the UI if
  you prefer.
  a.  Choose System -> Backup/Flash Firmware.
  b.  Click "Flash Image..." under "Flash new firmware image"
  c.  Click "Browse..." and then select the sysupgrade file.
  d.  Click Upload to upload the sysupgrade file.
  e.  Important:  uncheck "Keep settings and retain the current
      configuration" for this initial installation.
  f.  Click "Continue" to flash the firmware.
  g.  The device will reboot and OpenWRT is installed.

Extender (ALLY-00X19K)
1) This device requires a TFTP recovery procedure to do an initial load
  of OpenWRT.  Start by configuring a computer as a TFTP client:
  a. Install a TFTP client (server not necessary)
  b. Configure an Ethernet interface to 192.168.1.x/24; don't use .1 or .6
  c. Connect the Ethernet to the sole Ethernet port on the X19K.
2) Put the ALLY Extender in TFTP recovery mode.
  a. Do this by pressing and holding the reset button on the bottom while
  connecting the power.
  b. As soon as the LED lights up green (roughly 2-3 seconds), release
  the button.
3) Start the TFTP transfer of the Initramfs image from your setup machine.
For example, from Linux:
tftp -v -m binary 192.168.1.6 69 -c put initramfs.bin
4) The Extender will flash the OpenWrt initramfs image and reboot.  After
booting, LuCI will be available on 192.168.1.1.
5) Log into LuCI as root; there is no password.
6) Optional (but recommended) is to backup the OEM firmware before
  continuing; see process below.
7) Complete the Installation by flashing a full OpenWRT image.  Note: you
may use the sysupgrade command line tool in lieu of the UI if you prefer.
  a.  Choose System -> Backup/Flash Firmware.
  b.  Click "Flash Image..." under "Flash new firmware image"
  c.  Click "Browse..." and then select the sysupgrade file.
  d.  Click Upload to upload the sysupgrade file.
  e.  Important:  uncheck "Keep settings and retain the current
      configuration" for this initial installation.
  f.  Click "Continue" to flash the firmware.
  g.  The device will reboot and OpenWRT is installed.

Backup the OEM Firmware:
-----------------------

There isn't any downloadable firmware for the ALLY devices on the Amped
Wireless web site. Reverting back to the OEM firmware is not possible
unless we have a backup of the original OEM firmware.

The OEM firmware may be stored on either /dev/mtd3 ("firmware") or
/dev/mtd6 ("oem").  We can't be sure which was overwritten with the
initramfs image, so backup both partitions to be safe.

  1) Once logged into LuCI, navigate to System -> Backup/Flash Firmware.
  2) Under "Save mtdblock contents," first select "firmware" and click
  "Save mtdblock" to download the image.
  3) Repeat the process, but select "oem" from the pull-down menu.

Revert to the OEM Firmware:
--------------------------
* U-boot TFTP:
  Follow the TFTP recovery steps for the Extender, and use the
  backup image.

* OpenWrt "Flash Firmware" interface:
  Upload the backup image and select "Force update"
  before continuing.

Signed-off-by: Jonathan Sturges <jsturges@redhat.com>
2021-06-05 23:39:14 +02:00
Aashish Kulkarni
251c995cbb ramips: add support for Linksys E5600
This submission relied heavily on the work of Linksys EA7300 v1/ v2.

Specifications:

* SoC: MediaTek MT7621A (880 MHz 2c/4t)
* RAM: 128M DDR3-1600
* Flash: 128M NAND
* Eth: MediaTek MT7621A (10/100/1000 Mbps x5)
* Radio: MT7603E/MT7613BE (2.4 GHz & 5 GHz)
* Antennae: 2 internal fixed in the casing and 2 on the PCB
* LEDs: Blue (x4 Ethernet)
  Blue+Orange (x2 Power + WPS and Internet)
* Buttons: Reset (x1)
  WPS (x1)

Installation:

Flash factory image through GUI.

This device has 2 partitions for the firmware called firmware and
alt_firmware. To successfully flash and boot the device, the device
should have been running from alt_firmware partition. To get the device
booted through alt_firmware partition, download the OEM firmware from
Linksys website and upgrade the firmware from web GUI. Once this is done,
flash the OpenWrt Factory firmware from web GUI.

Reverting to factory firmware:

1. Boot to 'alt_firmware'(where stock firmware resides) by doing one of
   the following:
   Press the "wps" button as soon as power LED turns on when booting.
   (OR) Hard-reset the router consecutively three times to force it to
   boot from 'alt_firmware'.
2. To remove any traces of OpenWRT from your router simply flash the OEM
   image at this point.

Signed-off-by: Aashish Kulkarni <aashishkul@gmail.com>

[fix hanging indents and wrap to 74 characters per line,
 add kmod-mt7663-firmware-sta package for 5GHz STA mode to work,
 remove sysupgrade.bin and concatenate IMAGES instead in mt7621.mk,
 set default-state "on" for power LED]
Signed-off-by: Sannihith Kinnera <digislayer@protonmail.com>

[move check-size before append-metadata, remove trailing whitespace]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-06-05 23:39:14 +02:00
Philipp Borgers
fbc2feadd4 ramips: enable additional UART on MikroTik RouterBOARD M33G
The RouterBOARD M33G has an additional UART that should be enabled
by default.

Signed-off-by: Philipp Borgers <borgers@mi.fu-berlin.de>
2021-06-05 01:17:11 +02:00