The TP-link Deco X80-5G is a AX WIFI router with a single 1G (LAN) and 1 2.5G (WAN) port with a built in Quectel 5G modem.
Specifications:
Architecture ARMv8-A (aarch64 Cortex A53, 4 cores)
Vendor Qualcomm
Bootloader U-Boot (2016)
System-On-Chip Qualcomm IPQ8074A (Networking Pro 1210 platform)
CPU/Speed 2.2GHZ
Flash-Chip ESMT F59D1G81MB-45TI 1G-bit NAND
Flash MB 128MB (1Gbit)
RAM-chip 2* ESMT M15T4G16256A-DEBG2G 2Gb DDR3L (32bit)
RAM MB 512MB (4Gbit)
WLan System-On-Chip (5g) Qualcomm QCN5054
WLan Front end modules (5g) 8* Qorvo QPF4588
WLAN (5G) A/N/AC/AX
WLAN Antenna (int) 8* (4 shared with 2.5G)
WLan System-On-Chip (2.4G) Qualcomm QCN5024
WLan Front end modules (2.4G) 4* Skyworks SKY85340-11
WLAN (2.4G) B/G/N/AX
WLAN Antenna (int) 4* (shared with 5g)
Eithernet-phy (1Gbit) Qualcomm (Atheros) AR8033-AL1A
Ethernet (1Gbit) 1*
Eithernet-phy (2.5Gbit) Qualcomm QCA8081
Ethernet (2.5Gbit) 1*
Switch Embedded in the SOC?
Serial 1.8v 8n1 (testpoints)
Modem System-On-Chip Qualcomm 5G RG50xQ (Snapdragon X55 platform)
5G modem capability 5000Mbps down 900Mbps up
5G modem bands N1/N3/N5/N7/N8/N20/N28/N38/N40/N41/N77/N78/N79
4G modem capability 4.5G LTE-Advanced Pro (Cat20 down 2Gbps) (Cat18 up 200Mbps)
4G modem FDD bands B1/B3/B5/B7/B8/B18/B19/B20/B26/B28
4G modem TDD bands B34/B38/B39/B40/B41/B42/B43
Modem antenna (int) 8* (5G/4G use)
Modem antenna (ext) 2* SMA connectors (5G/4G use)
SIM type 1* Nano SIM
Telephony 1* POTS RJ11
(see wiki for more info:)
https://openwrt.org/inbox/toh/tp-link/x80-5g_v1
Notes:
Installation Instructions:
Between antennas 7 and 8 on the PCB with the RGB harness there are three test pads labelled TP1 TP2 and TP3 connections are as follows:
|TP2|-- RX
|TP1|-- TX
|TP3|-- GND
RX requires an external pullup to operate somewhere around 5 K ohm but your luck may vary the Uart is 1.8v
Set a static IP and set up a tftpserver and terminal.
power the router and quickly type the magic string “tpl” and press enter to break into u-boot
in the shell set the environment variables to enable tftp booting
setenv ipaddr (routerIP)
setenv serverip (server IP)
load you initramfs:
tftpboot 0x44000000 (serverIP):openwrt-qualcommax-ipq807x-tplink_x80-5g-initramfs-uImage.itb
boot your initramfs
bootm
upload your factory image to /tmp
format and install the factory image:
ubiformat /dev/mtd12 -y -f /tmp/openwrt-qualcommax-ipq807x-tplink_x80-5g-squashfs-factory.ubi
Note as this device swaps root partitions upon update your boot partition may be set as mtd13
Update script to mount factory tplink partition's for MAC recovery and device data.
Capture Labelmac from Factory_data partition.
Patch LAN from Labelmac.
Patch ART from Labelmac.
Set GPIO to make modem operational from boot.
GPIO fan tables work like the stock device with three fan maps high active idle with a top fan speed of 6800 RPM.
High temp 70 deg speeds 6-8
Active temp 50 deg speeds 2-5
low temp 25 degree speed 0-1
Signed-off-by: jonathan brophy <professor_jonny@hotmail.com>
Link: https://github.com/openwrt/openwrt/pull/16329
Signed-off-by: Robert Marko <robimarko@gmail.com>
Patch script used for mounting of factory data partitions to not assume devices names or use hardcoded identifiers.
Signed-off-by: jonathan brophy <professor_jonny@hotmail.com>
Link: https://github.com/openwrt/openwrt/pull/16329
Signed-off-by: Robert Marko <robimarko@gmail.com>
Create factory tar for WAX620 and WAX630 which is accepted by the stock UI.
Must use 'Boot up Backup Firmware' button on stock upgrade page after install and reboot to swap partitions.
Signed-off-by: Erik Servili <serverror@serverror.com>
Link: https://github.com/openwrt/openwrt/pull/18334
Signed-off-by: Robert Marko <robimarko@gmail.com>
Function remove_oem_ubi_volume was called before CI_UBIPART variable was defined.
Fixes: df1f6e1e18 (qualcommax: ipq807x: Remove OEM UBI volume before upgrade for Linksys MX devices)
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18090
Signed-off-by: Robert Marko <robimarko@gmail.com>
Aliyun AP8220 is an AP manufactured by Edgecore.
(Very similar to Edgecore EAP102)
Hardware specifications:
SoC: Qualcomm IPQ8071A
RAM: 1GB of DDR4 600MHz
Flash1: MX25U3235F 4MB
Flash2: MX30UF1G18AC 128MB
Ethernet: 2x 2.5G RJ45 port
USB: 2x USB-A 2.0 port
WiFi1: QCN5024 2.4GHz
WiFi2: QCN5054 5GHz
Power: DC 12V / PoE
Flash instructions:
1. Connect the router via serial port
2. Keep pressing @ until uboot is interrupted
3. Download the initramfs image, rename it to
initramfs.bin, host it with tftp server
4. Run these commands:
tftpboot initramfs.bin
bootm
5. After openwrt boots up, use scp or luci
to upload sysupgrade.bin to upgrade.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/17970
Signed-off-by: Robert Marko <robimarko@gmail.com>
Cleanup 02_network script indentation.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/17970
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use 'remove_oem_ubi_volume' function to remove OEM UBI volume before upgrade.
This allows to upgrade even if we have OEM firmware on the second partition.
Applies to Linksys MX4200/MX4300/MX5300/MX8500.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14720
Signed-off-by: Robert Marko <robimarko@gmail.com>
Update u-boot env variables only when changes are made.
Applies to Linksys MX4200/MX4300/MX5300/MX8500.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14720
Signed-off-by: Robert Marko <robimarko@gmail.com>
Dual firmware devices like Linksys MX4200, MX4300, MX5300 and MX8500 use separate rootfs partition.
This option helps to keep all configuration during upgrade.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14720
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fixed an issue where both WAN LEDs light up before plugging in the
ethernet cable and no blinking regardless of WAN network activity.
Updated the LED configuration to reflect proper status:
Green indicates 2.5Gb connection speed.
Yellow indicates other connection speed and traffic activity.
This resolves inconsistent WAN LED behavior on Spectrum SAX1V1K routers.
Signed-off-by: Ivan Deng <hongba@rocketmail.com>
Link: https://github.com/openwrt/openwrt/pull/17623
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently for Linksys MX4200v2 all u-boot ethXaddr variables share the same MAC address
and there is no need to check them one by one.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16070
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
* SoC: Qualcomm IPQ8072A (64-bit Quad-core Arm Cortex-A53 @ 1.4 GHz)
* Memory: 2x ESMT M15T4G16256A-DEBG2G (1 GiB DDR3-1866 13-13-13)
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: QCA5054 (4x4 5 GHz 802.11ax)
* Wi-Fi: QCN5024 (2x2 2.4 GHz 802.11b/g/n/ax)
* Ethernet: AR8031 (10/100/1000BASE-T)
* Flash: Winbond W29N01HZSINF (128 MiB)
* LEDs: 1x Blue Status (GPIO 42 Active High)
* Buttons: 1x Reset (GPIO 50 Active Low)
Installation Instructions (Serial+TFTP):
1. Solder 4 pin header to JP1 and bridge pads of R58 and R62.
2. Connect 3V3 TTL port to TX, RX, and GND, which are positions 1, 2, and 3 respectively.
Be sure to crossover TX and RX.
3. Copy RAM firmware
openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-initramfs-uImage.itb
to a TFTP server's root that is in the same subnet as your AP.
4. Power up the AP hold Ctrl+B in the serial console (115200n8) until autoboot is halted.
5. Run the following commands in the U-boot prompt:
# setenv serverip <TFTP server addr>
# setenv ipaddr <addr of AP>
# tftpboot 0x44000000 openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-initramfs-uImage.itb
# bootm
You may need to type Ctrl+C and Enter before running these commands
to clear invisible characters from the buffer.
6. Run the following command in a terminal to copy the sysupgrade image
to be installed (check IP address):
$ scp -O openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
7. Activate the OpenWrt serial console and run the following commands:
# cd /tmp
# sysupgrade -n openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-squashfs-sysupgrade.bin
8. The AP will reboot and OpenWrt will be successfully installed.
Known Issues:
* 5GHz radio instability (upstream current ath11k build bug maybe?)
Device support directly followed from EAP660HDv1 support
Links: #15832
Signed-off-by: Shymon Samsel <ssamsel@umass.edu>
Link: https://github.com/openwrt/openwrt/pull/17254
Signed-off-by: Robert Marko <robimarko@gmail.com>
Userspace regulator consumer is rather usefull so enable it for ipq60xx
as well and remove from ipq807x only kernel config.
Link: https://github.com/openwrt/openwrt/pull/14807
Signed-off-by: Robert Marko <robimarko@gmail.com>
All ipq807x devices that were using the legacy 'mmc_do_upgrade' eMMC
sysupgrade code were ported to the replacement 'emmc_do_upgrade' code.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16505
Signed-off-by: Robert Marko <robimarko@gmail.com>
Alphabetically sort devices in platform.sh
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16505
Signed-off-by: Robert Marko <robimarko@gmail.com>
Note that the old ad-hoc method did not explicitly align backup data
to 64 KiB boundaries.
Also note that the qnap 301w has a 'rootfs_data' partition in the eMMC
that is being ignored by fstools during boot, presumably due to a bug.
This is why the partition is also ignored in the sysupgrade code and
there is no definition of CI_DATAPART="rootfs_data".
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16505
Signed-off-by: Robert Marko <robimarko@gmail.com>
Note that the old ad-hoc method did not explicitly align backup data
to 64 KiB boundaries.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16505
Signed-off-by: Robert Marko <robimarko@gmail.com>
Before this commit, sysupgrade saved the settings backup data to
the area following rootfs even though the device has an actual
rootfs_data partition. The backup data was completely ignored on
the following boot, but since rootfs_data was not being cleared
during sysupgrade, the issue was not noticed earlier.
Note that this commit changes the filesystem of rootfs_data from
ext4 to F2FS (if OEM partitioning is used).
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16463
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
* SoC: Qualcomm IPQ8072A (64-bit Quad-core Arm Cortex-A53 @ 2200MHz)
* Memory: 2x ESMT M15T4G16256A-DEBG2G (1 GiB DDR3-1866 13-13-13)
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: QCN5054 (4x4 5 GHz 802.11ax)
* Wi-Fi: QCN5024 (4x4 2.4 GHz 802.11b/g/n/ax)
* Ethernet: QCA8081 (10/100/1000/2.5GBASE-T)
* Flash: Winbond W29N01HZSINF (128 MiB)
* LEDs: 1x Blue Status (GPIO 42 Active High)
* Buttons: 1x Reset (GPIO 50 Active Low)
Installation Instructions (Serial+TFTP):
1. Solder 4 pin header to JP1 and bridge pads of R58 and R62.
2. Connect 3V3 TTL port to TX, RX, and GND, which are positions 1, 2,
and 3 respectively. Be sure to crossover TX and RX.
3. Copy RAM firmware image
openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-initramfs-uImage.itb
to TFTP server root, available at 192.168.10.1.
4. Connect PoE ethernet cable to the RJ45 port and hold Ctrl+B in the
serial console (115200 baud) until autoboot is halted.
5. Run the following commands in the U-boot prompt:
# tftpboot 0x44000000 openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-initramfs-uImage.itb
# bootm
You may need to type Ctrl+C and Enter before running these commands
to clear invisible characters from the buffer.
6. Run the following command in a terminal to copy the sysupgrade image
to be installed (check IP address):
$ scp openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
7. Activate the OpenWrt serial console and run the following commands:
# cd /tmp
# sysupgrade -n openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-squashfs-sysupgrade.bin
8. The AP will reboot and OpenWrt will be successfully installed.
Signed-off-by: George Witt <george.witt@nltsproject.org>
Link: https://github.com/openwrt/openwrt/pull/15832
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds support for Asus RT-AX89X BX revision.
WARNING: Only the BX revision boards (So B1, B2 etc) are supported because
AX revision boards use IPQ8074 v1 SoC which is unsupported.
Specifications:
---------------
* CPU: Qualcomm IPQ8074A Quad core Cortex-A53 @ 2.2GHz
* RAM: 1024MB
* Storage: 256MB SLC NAND (Macronix MX30UF2G18AC)
* Ethernet:
* 5x 1G RJ45 ports via QCA8337 switch
* 3x 1G RJ45 ports via internal switch (QCA8075 PHY)
* 1x 10G RJ45 via internal switch (AQR113C PHY)
* 1x 10G SFP+ slot via internal switch
* WLAN:
* 2.4GHz 4x4
* 5GHz 8x8
* 8 external antennas
* USB: 2x USB 3.0 Type-A
* Buttons:
* Power switch
* WPS
* Reset
* Wireless ON/OFF
* LED ON/OFF
LED-s:
* Power
* Wi-Fi
* WAN
* 10G
* SFP+
Power:
* 19.5V via DC jack
Installation instructions:
--------------------------
1. Flash temporary OpenWrt initramfs:
* Flash openwrt-qualcommax-ipq807x-asus_rt-ax89x-initramfs-factory.trx
via the stock firmware.
Administration -> Firmware Upgrade -> Manual Firmware update (Upload)
After flashing the device will reboot with OpenWrt initramfs and it can
be accesed via any of the LAN ports via SSH with the usual OpenWrt
default credentials.
2. Sysupgrade from OpenWrt initramfs:
* Copy openwrt-qualcommax-ipq807x-asus_rt-ax89x-squashfs-sysupgrade.bin to
/tmp/openwrt-qualcommax-ipq807x-asus_rt-ax89x-squashfs-sysupgrade.bin of
the running initramfs image.
* Simply sysupgrade -n /tmp/openwrt-qualcommax-ipq807x-asus_rt-ax89x-squashfs-sysupgrade.bin
After flashing the device will reboot with OpenWrt initramfs and it can
be accesed via any of the LAN ports via SSH with the usual OpenWrt
default credentials.
Link: https://github.com/openwrt/openwrt/pull/15840
Signed-off-by: Robert Marko <robimarko@gmail.com>
Asus RT-AX89X has an external QCA8337 switch that has built-in
internal ethernet PHY-s that are supported by the QCA83XX PHY driver so
lets enable it.
Link: https://github.com/openwrt/openwrt/pull/15840
Signed-off-by: Robert Marko <robimarko@gmail.com>
Asus RT-AX89X has an Qualcomm QCA8337 switch used to provide additional
1G copper ports, so lets enable qca8k in order to utilize DSA instead of
relying on SSDK for it.
Link: https://github.com/openwrt/openwrt/pull/15840
Signed-off-by: Robert Marko <robimarko@gmail.com>
Asus RT-AX89X is using GPIO bitbanged MDIO on newer HW revisions, so lets
enable it in kernel config.
Link: https://github.com/openwrt/openwrt/pull/15840
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use ath11k_patch_mac and ath11k_set_macflag functions for SXK80
Signed-off-by: Andrew Smith <gul.code@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/15732
Signed-off-by: Robert Marko <robimarko@gmail.com>
This router has two rootfs partitions and dualboot is used.
Vendor firmware may swap the rootfs partition location, u-boot append
'ubi.mtd=rootfs' in the end of cmdline. Since we use fixed-partitions,
force boot from the first rootfs partition to avoid boot failure.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/15700
Signed-off-by: Robert Marko <robimarko@gmail.com>
The wifi radios on wax620 and wax630 got a random mac
address on boot. So fix this by using ath11k_patch_mac
and give a static mac address from label-mac-device.
Tested and working on wax620 and wax630.
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Link: https://github.com/openwrt/openwrt/pull/15597
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use ath11k_patch_mac and ath11k_set_macflag functions
instead of fix_wifi_mac script.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/15580
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds support for Netgear Orbi Pro SXR80 and SXS80 (collectively known as SXK80)
Specifications:
---------------
* CPU: Qualcomm IPQ8074A Quad core Cortex-A53
* RAM: 1024MB
* Storage: SPI-NAND 512 MiB (Winbond W29N04GZ)
* Ethernet: 4x 1G RJ45 ports (QCA8075) 1x 2.5G RJ45 LAN/WAN (QCA8081)
* WLAN:
- 2.4 GHz: Qualcomm QCN5024 4x4
- 2x 5 GHz: Qualcomm QCN5054 4x4 (second radio high channels only)
* LEDs:
- Power: (Green and red)
- Front: (Blue, green, red and white)
* Buttons:
- 1x Soft reset
- 1x Sync/WPS
* Power: 12V DC Jack
Installation instructions (Telnet):
-----------------------------------
*Note, this guide assumes SXR80, for SXS80 change the firmware file name as appropriate
1. Put firmware file openwrt-qualcommax-ipq807x-netgear_sxr80-initramfs-uImage.itb in root of TFTP server available at 192.168.1.10.
2. Enable telnet by going to http://[ip of device]/debug.htm and clicking on the tickbox 'Enable telnet'
3. Telnet into the device and login using the same username and password as the web interface:
4. Run the following command:
`fw_setenv bootcmd 'env default -a; saveenv; reset'`
5. Reboot the router, once the web interface is available again re-enable telnet via http://[ip of device]/debug.htm and telnet into the device.
6. Run the following command:
`fw_printenv`
It should look similar to the below:
```
baudrate=115200
bootargs=console=ttyMSM0,115200n8
bootcmd=mii write 0x0 0x0 0x800; sleep 1; nmrp; bootdni; boot_DNI_secureboot
bootdelay=2
ipaddr=192.168.1.1
netmask=255.255.255.0
serverip=192.168.1.10
soc_version_major=2
soc_version_minor=0
```
**If you see the message:**
`Warning: Bad CRC, using default environment`
**DO NOT CONTINUE, YOU WILL BRICK YOUR DEVICE**
7. Run the following command:
`fw_setenv originalboot 'mii write 0x0 0x0 0x800; sleep 1; nmrp; bootdni; boot_DNI_secureboot'`
(This should match what's in the bootcmd variable displayed in step 6)
8. Run the following commands:
```
fw_setenv wrttftp 'mii write 0x0 0x0 0x800; sleep 1; nmrp; if tftpboot openwrt-qualcommax-ipq807x-netgear_sxr80-initramfs-uImage.itb; then bootm; fi; bootdni; boot_DNI_secureboot'
fw_setenv wrtboot 'mii write 0x0 0x0 0x800; sleep 1; nmrp; nand read 0x40000000 0x1980000 0x06d00000; bootm 0x40000000'
fw_setenv bootcmd 'run wrttftp'
```
9. Ensure SXR/S device is attached via ethernet (LAN port) to the same ethernet segment as the TFTP server.
10. Reboot the device, it should reboot into OpenWrt and be available on 192.168.1.1
11. Once OpenWrt has booted, update the bootcmd using the following command:
`fw_setenv bootcmd 'run wrtboot'`
12. Flash the sysupgrade image
13. It should boot into OpenWrt
References to SXK80 GPL source:
https://www.downloads.netgear.com/files/GPL/SXK80-V3.2.0.108_gpl_src.tar.bz2.zip
Signed-off-by: Flole Systems <flole@flole.de>
Signed-off-by: Andrew Smith <gul.code@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/14939
Signed-off-by: Robert Marko <robimarko@gmail.com>
Hardware specification:
========
SoC: Qualcomm IPQ8072A
Flash: 512MB (Fidelix FMND4G08S3J-ID)
RAM: 1GB (2x Kingston DDR3L D2516ECMDXGJD)
Ethernet: 1x 10/100/1000/2500/5000Mbps (Marvell AQR114C)
Ethernet: 4x 10/100/1000Mbps (Qualcomm QCA8075)
WiFi1: 6GHz ax 4x4 (Qualcomm QCN9024 + Skyworks SKY85784-11) - channels 33-229
WiFi2: 5GHz ax 4x4 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 36-177
WiFi3: 2.4GHz ax 4x4 (Qualcomm QCN5024 + Skyworks SKY8340-11)
IoT: Bluetooth 5, Zigbee and Thread (NXP K32W041)
LED: 1x RGB status (NXP PCA9633)
USB: 1x USB 3.0
Button: WPS, Reset
Flash instructions:
========
1. Manually upgrade firmware using openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin image.
More details can be found here: https://www.linksys.com/support-article?articleNum=47547
After first boot check actual partition:
- fw_printenv -n boot_part
and install firmware on second partition using command in case of 2:
- mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin kernel
and in case of 1:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin alt_kernel
2. Installation using serial connection from OEM firmware (default login: root, password: admin):
- fw_printenv -n boot_part
In case of 2:
- flash_erase /dev/mtd21 0 0
- nandwrite -p /dev/mtd21 openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin
or in case of 1:
- flash_erase /dev/mtd23 0 0
- nandwrite -p /dev/mtd23 openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin
After first boot install firmware on second partition:
- mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin kernel
or:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin alt_kernel
3. Installation from initramfs image using USB drive:
Put the initramfs image on the USB drive:
- dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_mx8500-initramfs-uImage.itb of=/dev/sda
Stop u-boot and run:
- usb start && usbboot $loadaddr 0 && bootm $loadaddr
Write firmware to the flash from initramfs:
- mtd -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin kernel
and:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin alt_kernel
4. Back to the OEM firmware:
- mtd -e kernel -n write FW_MX8500_1.0.11.208937_prod.img kernel
and:
- mtd -r -e alt_kernel -n write FW_MX8500_1.0.11.208937_prod.img alt_kernel
5. USB recovery:
Put the initramfs image on the USB:
- dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_mx8500-initramfs-uImage.itb of=/dev/sda
Set u-boot env:
- fw_setenv bootusb 'usb start && usbboot $loadaddr 0 && bootm $loadaddr'
- fw_setenv bootcmd 'run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
AQR firmware:
========
1. Firmware loading:
To properly load the firmware and initialize AQR PHY, we must use the u-boot aq_load_fw function.
To do this, you need to modify u-boot env:
With USB recovery:
- fw_setenv bootcmd 'aq_load_fw; run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
and without:
- fw_setenv bootcmd 'aq_load_fw; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
2. Firmware updating:
Newer firmware (AQR-G4_v5.6.5-AQR_WNC_SAQA-L2_GT_ID45287_VER24005.cld) is available in the latest OEM firmware.
To load this firmware via u-boot, we need to add the MBN header and update 0:ethphyfw partition.
For MBN header we can use script from this repository: https://github.com/testuser7/aqr_mbn_tool
- python aqr_mbn_tool.py AQR-G4_v5.6.5-AQR_WNC_SAQA-L2_GT_ID45287_VER24005.cld
To update partition we need to install kmod-mtd-rw package first:
- insmod mtd-rw.ko i_want_a_brick=1
- mtd -e /dev/mtd26 -n write aqr_fw.mbn /dev/mtd26
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14883
Signed-off-by: Robert Marko <robimarko@gmail.com>
For this particualar device we get random MAC's for Wifi on each (re-)boot.
This is because art partition/pre caldata do not contain valid MAC addresses.
As we have now a new/better approach with ath11k_patch_mac we can use it for
this device too.
I'm using this approach for like two weeks and its working flawlessly.
Signed-off-by: Ulrich Stark <pwned-pixel@posteo.de>
qualcommax: IPQ807x: ZyXEL NBG7815: Fix random Wifi MAC
Changing order to 3/phy0/5G-1, 2/phy1/2G, 4/phy2/5G-2.
Signed-off-by: Ulrich Stark <pwned-pixel@posteo.de>
Use ath11k_patch_mac and ath11k_set_macflag functions for RAX120v2 (pre-caldata does not contain valid MAC addresses)
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Use ath11k_patch_mac, ath11k_remove_regdomain and ath11k_set_macflag functions for MX4200
(only v2 variant requires MAC patching)
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Spectrum SAX1V1K is a AX WIFI router with 3 1G and 1 2.5G ports.
The router is provided to Spectrum customers.
It is OEM of Askey RT5010W
https://forum.openwrt.org/t/spectrum-sax1v1k-askey-rt5010w-openwrt-support/149923
It continues the original work by @MeisterLone to get this device supported.
Specifications:
```
• CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
• RAM: 2048MB of DDR3
• Storage: 1024MB eMMC
• Ethernet: 3x 1G RJ45 ports (QCA8075) + 1 2.5G Port (QCA8081)
• WLAN:
• 2.4GHz: Qualcomm QCN5024 4x4 802.11b/g/n/ax 1174 Mbps PHY rate
• 5GHz: Qualcomm QCN5054 4x4 802.11a/b/g/n/ac/ax 2402 PHY rate
• LED: 1 gpio-controlled dual color led (blue/red)
• Buttons: 1x reset
• Power: 12V DC jack
```
Notes:
```
• This commit adds only single partition support, that means
sysupgrade is upgrading the current rootfs partition.
• Installation can be done by serial connection only.
• A poulated serial header is onboard
https://forum.openwrt.org/t/spectrum-sax1v1k-askey-rt5010w-openwrt-support/149923/6
• RX/TX is working, u-boot bootwait is active, secure boot is enabled.
```
Installation Instructions:
**Most part of the installation is performed from an initramfs image.**
Boot initramfs : Using serial connection
1. Boot up the device and wait till it displays "VERIFY_IB: Success. verify IB ok"
2. Once that message appears,
login with username 'root'
password serial number of your router in uppercase.
3. Use vi to paste the 'open.sh' script from @MeisterLone github on your device
https://github.com/MeisterLone/Askey-RT5010W-D187-REV6/blob/master/Patch/open.sh
4. chmod 755 open.sh
5. ./open.sh
6. Set your ip to 192.168.0.1
7. Run a TFTP server and host the initramfs image on the TFTP server and name it "recovery.img"
8. Reboot device. On boot it will try TFTP.
Install OpenWrt from initramfs image:
1. Use SCP (or other way) to transfer OpenWrt factory image
2. Connect to device using SSH (on a LAN port)
3. Flash firmware: sysupgrade
# sysupgrade -n -v /tmp/openwrt_sysupgrade.bin
4. Set U-boot env variable: bootcmd
# fw_setenv bootcmd "run fix_uboot; run setup_and_boot"
5. Reboot the device
# reboot
6. Once device is booted, residue of previous firmware will prevent openwrt to work properly.
Factory Reset is MUST required
# Once serial console is displaying to login, hold reset button for 10 sec
7. Now everything should be operational.
Note: this PR adds only single partition support, that means sysupgrade is
upgrading the current rootfs partition
Signed-off-by: Connor Yoon <j_connor@taliaent.com>
Kernel 6.6 has changed the path of WLAN devices as the soc node was updated
to include an adress as well because according to spec it needed one:
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/arm64/boot/dts/qcom/ipq8074.dtsi?h=v6.6.21&id=da6aa1111a17db11367817ddc10c5a6c188cdc44
So, this will break existing configuration as device path was changed for
example:
"platform/soc/c000000.wifi" to "platform/soc@0/c000000.wifi"
"platform/soc/c000000.wifi+1" to "platform/soc@0/c000000.wifi+1"
PCIe attached devices also have their path changed, so lets add a script
that will migrate the paths based on the detected running kernel version
so returning to kernel 6.1 will work as well.
Co-developed-by: Sean Khan <datapronix@protonmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
On QNAP QHora-301W, all LEDs don't have "function" property and only
"color" property is available for the newer binding of LED on Linux
Kernel.
2e659930d3 ("qualcommax: drop redundant label with new LED
color/function format") removes "label" property from LEDs, then,
multiple "<color>:" (ex.: "amber:"/"green:"/"red:") will be appeared as
LED names and renamed to "<color>:_<num>" ("ex.: "green:_1", "green:_2",
...) by kernel.
logs:
[ 4.246494] leds-gpio leds: Led green: renamed to green:_1 due to name collision
[ 4.248978] leds-gpio leds: Led green: renamed to green:_2 due to name collision
[ 4.256345] leds-gpio leds: Led green: renamed to green:_3 due to name collision
[ 4.263770] leds-gpio leds: Led green: renamed to green:_4 due to name collision
[ 4.271105] leds-gpio leds: Led amber: renamed to amber:_1 due to name collision
[ 4.278487] leds-gpio leds: Led green: renamed to green:_5 due to name collision
[ 4.285856] leds-gpio leds: Led amber: renamed to amber:_2 due to name collision
[ 4.293257] leds-gpio leds: Led green: renamed to green:_6 due to name collision
[ 4.300616] leds-gpio leds: Led amber: renamed to amber:_3 due to name collision
[ 4.308002] leds-gpio leds: Led green: renamed to green:_7 due to name collision
[ 4.315384] leds-gpio leds: Led amber: renamed to amber:_4 due to name collision
[ 4.322760] leds-gpio leds: Led green: renamed to green:_8 due to name collision
[ 4.330135] leds-gpio leds: Led amber: renamed to amber:_5 due to name collision
/sys/class/leds:
amber: amber:_4 green:_2 green:_6
amber:_1 green:_5 green:_3 green:_7
amber:_2 green: green:_4 green:_8
amber:_3 green:_1 green:_5 red:
Fix this issue by adding missing "function" (and "function-enumerator")
property to LEDs on QNAP QHora-301W.
Note: there are no appropriate functions in dt-bindings/leds/common.h
for some LEDs, so use the hardcoded strings for them instead.
Fixes: 2e659930d3 ("qualcommax: drop redundant label with new LED color/function format")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Since we can configure the PHY LED of the qca8081,
add a configuration for this device.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Xiaomi AX9000 apply a special PHY LEDs configuration where the unique
green LED for each qca807x PHY port is turned on also on 1000Mbps link.
Apply this special configuration to reflect original implementation.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Xiaomi AX3600 apply a special PHY LEDs configuration where the unique
green LED for each qca807x PHY port is turned on also on 1000Mbps link.
Apply this special configuration to reflect original implementation.
Also enable CONFIG_PHYLIB_LEDS to actually expose the PHY LEDs if
defined in DT.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Switch to qca8081 upstream PHY. Update every device that have LEDs
attached to the qca8081 PHY to follow new way of defining the LEDs and
add original OEM configuration.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
By default Linux will default to most IRQ-s being mapped to core 0 which
during high loads will completely swamp the core 0, so lets add the widely
used script that has been floating around forums for a long time to try and
optimize the IRQ mapping a bit.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Some devices (MX42CF) have a wrong MAC address configuration. The correct one is located only on the devinfo partition.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Currently, WiFi interfaces on WXR-5950AX12 / WXR-6000AX12 devices
come up with some MAC addresses inconsistent with vendor and Ethernet
addresses. This adds a hotplug override in order to make it consistent
with what is in u-boot env as well as OAM firmware where 1st radio MAC
is set at Ethernet MAC + 8, and 2nd radio mac at Ethernet MAC + 16.
fw_printenv | grep addr
ethaddr=68:e1:dc:xx:xx:d8
ipaddr=192.168.11.1
wlan0addr=68:e1:dc:xx:xx:e0
wlan1addr=68:e1:dc:xx:xx:e8
wlan2addr=00:00:00:00:00:00
For OEM bootlog and MAC assagnment check
https://openwrt.org/toh/buffalo/wxr-5950ax12#openwrt_uimage_tftp_bootlog
Tested-by: Samir Ibradžić <sibradzic@gmail.com> # Buffalo WXR-6000AX12P
Signed-off-by: Samir Ibradžić <sibradzic@gmail.com>
