2022-07-16 20:07:20 +00:00
|
|
|
#
|
|
|
|
|
# Copyright (C) 2021 OpenWrt.org
|
|
|
|
|
#
|
|
|
|
|
|
|
|
|
|
[ -e /etc/config/ubootenv ] && exit 0
|
|
|
|
|
|
|
|
|
|
touch /etc/config/ubootenv
|
|
|
|
|
|
|
|
|
|
. /lib/uboot-envtools.sh
|
|
|
|
|
. /lib/functions.sh
|
|
|
|
|
|
|
|
|
|
board=$(board_name)
|
|
|
|
|
|
|
|
|
|
case "$board" in
|
2023-11-20 07:18:00 +00:00
|
|
|
asus,rt-ax59u)
|
|
|
|
|
ubootenv_add_uci_config "/dev/mtd0" "0x100000" "0x20000" "0x20000"
|
|
|
|
|
;;
|
2022-07-16 20:07:20 +00:00
|
|
|
bananapi,bpi-r3)
|
2023-01-29 03:42:15 +00:00
|
|
|
rootdev="$(cmdline_get_var root)"
|
|
|
|
|
rootdev="${rootdev##*/}"
|
|
|
|
|
rootdev="${rootdev%%p[0-9]*}"
|
|
|
|
|
case "$rootdev" in
|
|
|
|
|
mmc*)
|
2022-07-16 20:07:20 +00:00
|
|
|
local envdev=$(find_mmc_part "ubootenv" $rootdev)
|
|
|
|
|
ubootenv_add_uci_config "$envdev" "0x0" "0x40000" "0x40000" "1"
|
|
|
|
|
ubootenv_add_uci_config "$envdev" "0x40000" "0x40000" "0x40000" "1"
|
|
|
|
|
;;
|
2023-01-29 03:42:15 +00:00
|
|
|
mtd*)
|
2022-07-16 20:07:20 +00:00
|
|
|
local envdev=/dev/mtd$(find_mtd_index "u-boot-env")
|
|
|
|
|
ubootenv_add_uci_config "$envdev" "0x0" "0x20000" "0x20000" "1"
|
|
|
|
|
ubootenv_add_uci_config "$envdev" "0x20000" "0x20000" "0x20000" "1"
|
|
|
|
|
;;
|
2023-01-29 03:42:15 +00:00
|
|
|
ubi*)
|
2022-07-16 20:07:20 +00:00
|
|
|
. /lib/upgrade/nand.sh
|
|
|
|
|
local envubi=$(nand_find_ubi ubi)
|
|
|
|
|
local envdev=/dev/$(nand_find_volume $envubi ubootenv)
|
|
|
|
|
local envdev2=/dev/$(nand_find_volume $envubi ubootenv2)
|
|
|
|
|
ubootenv_add_uci_config "$envdev" "0x0" "0x1f000" "0x1f000" "1"
|
|
|
|
|
ubootenv_add_uci_config "$envdev2" "0x0" "0x1f000" "0x1f000" "1"
|
|
|
|
|
;;
|
|
|
|
|
esac
|
|
|
|
|
;;
|
mediatek: add CMCC RAX3000M support
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 64GB eMMC or 128 MB SPI-NAND
RAM: 512MB
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, Mesh
Power: DC 12V 1A
- UART: 3.3v, 115200n8
--------------------------
| Layout |
| ----------------- |
| 4 | GND TX VCC RX | <= |
| ----------------- |
--------------------------
Gain SSH access:
1. Login into web interface, and download the configuration.
2. Enter fakeroot, decompress the configuration:
tar -zxf cfg_export_config_file.conf
3. Edit 'etc/config/dropbear', set 'enable' to '1'.
4. Edit 'etc/shadow', update (remove) root password:
'root::19523:0:99999:7:::'
5. Repack 'etc' directory:
tar -zcf cfg_export_config_file.conf etc/
* If you find an error about 'etc/wireless/mediatek/DBDC_card0.dat',
just ignore it.
6. Upload new configuration via web interface, now you can SSH to RAX3000M.
Check stroage type:
Check the label on the back of the device:
"CH EC CMIIT ID: xxxx" is eMMC version
"CH CMIIT ID: xxxx" is NAND version
eMMC Flash instructions:
1. SSH to RAX3000M, and backup everything, especially 'factory' part.
('data' partition can be ignored, it's useless.)
2. Write new GPT table:
dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-gpt.bin of=/dev/mmcblk0 bs=512 seek=0 count=34 conv=fsync
3. Erase and write new BL2:
echo 0 > /sys/block/mmcblk0boot0/force_ro
dd if=/dev/zero of=/dev/mmcblk0boot0 bs=512 count=8192 conv=fsync
dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-preloader.bin of=/dev/mmcblk0boot0 bs=512 conv=fsync
4. Erase and write new FIP:
dd if=/dev/zero of=/dev/mmcblk0 bs=512 seek=13312 count=8192 conv=fsync
dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-bl31-uboot.fip of=/dev/mmcblk0 bs=512 seek=13312 conv=fsync
5. Set static IP on your PC:
IP 192.168.1.254, GW 192.168.1.1
6. Serve OpenWrt initramfs image using TFTP server.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt has booted, perform sysupgrade.
9. Additionally, if you want to have eMMC recovery boot feature:
(Don't worry! You will always have TFTP recovery boot feature.)
dd if=openwrt-mediatek-filogic-cmcc_rax3000m-initramfs-recovery.itb of=/dev/mmcblk0p4 bs=512 conv=fsync
NAND Flash instructions:
1. SSH to RAX3000M, and backup everything, especially 'Factory' part.
2. Erase and write new BL2:
mtd erase BL2
mtd write openwrt-mediatek-filogic-cmcc_rax3000m-nand-preloader.bin BL2
3. Erase and write new FIP:
mtd erase FIP
mtd write openwrt-mediatek-filogic-cmcc_rax3000m-nand-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, erase UBI volumes:
ubidetach -p /dev/mtd0
ubiformat -y /dev/mtd0
ubiattach -p /dev/mtd0
8. Create new ubootenv volumes:
ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
9. Additionally, if you want to have NAND recovery boot feature:
(Don't worry! You will always have TFTP recovery boot feature.)
ubimkvol /dev/ubi0 -n 2 -N recovery -s 20MiB
ubiupdatevol /dev/ubi0_2 openwrt-mediatek-filogic-cmcc_rax3000m-initramfs-recovery.itb
10. Perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 423186d7d8b4f23aee91fca4f1774a195eba00d8)
[rebased to 23.05]
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-09-23 07:04:09 +00:00
|
|
|
cmcc,rax3000m)
|
|
|
|
|
case "$(cmdline_get_var root)" in
|
|
|
|
|
/dev/mmc*)
|
|
|
|
|
local envdev=$(find_mmc_part "ubootenv" "mmcblk0")
|
|
|
|
|
ubootenv_add_uci_config "$envdev" "0x0" "0x40000" "0x40000" "1"
|
|
|
|
|
ubootenv_add_uci_config "$envdev" "0x40000" "0x40000" "0x40000" "1"
|
|
|
|
|
;;
|
|
|
|
|
*)
|
|
|
|
|
. /lib/upgrade/nand.sh
|
|
|
|
|
local envubi=$(nand_find_ubi ubi)
|
|
|
|
|
local envdev=/dev/$(nand_find_volume $envubi ubootenv)
|
|
|
|
|
local envdev2=/dev/$(nand_find_volume $envubi ubootenv2)
|
|
|
|
|
ubootenv_add_uci_config "$envdev" "0x0" "0x1f000" "0x1f000" "1"
|
|
|
|
|
ubootenv_add_uci_config "$envdev2" "0x0" "0x1f000" "0x1f000" "1"
|
|
|
|
|
;;
|
|
|
|
|
esac
|
|
|
|
|
;;
|
2023-11-10 18:50:38 +00:00
|
|
|
comfast,cf-e393ax)
|
|
|
|
|
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x20000" "0x80000"
|
|
|
|
|
;;
|
2023-08-30 11:50:54 +00:00
|
|
|
cetron,ct3003|\
|
2023-12-09 12:39:53 +00:00
|
|
|
netgear,wax220|\
|
2023-12-09 04:48:35 +00:00
|
|
|
zbtlink,zbt-z8102ax|\
|
|
|
|
|
zbtlink,zbt-z8103ax)
|
2023-06-30 10:34:38 +00:00
|
|
|
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x20000" "0x20000"
|
2023-09-17 14:59:48 +00:00
|
|
|
;;
|
2023-05-20 15:03:06 +00:00
|
|
|
h3c,magic-nx30-pro|\
|
2023-06-15 15:21:40 +00:00
|
|
|
jcg,q30-pro|\
|
2023-04-28 15:36:17 +00:00
|
|
|
qihoo,360t7|\
|
2022-12-02 04:29:58 +00:00
|
|
|
tplink,tl-xdr4288|\
|
|
|
|
|
tplink,tl-xdr6086|\
|
|
|
|
|
tplink,tl-xdr6088|\
|
2023-11-27 09:01:34 +00:00
|
|
|
xiaomi,mi-router-ax3000t-ubootmod|\
|
2023-07-20 17:42:58 +00:00
|
|
|
xiaomi,mi-router-wr30u-ubootmod|\
|
uboot-mediatek: add support for Xiaomi Redmi Router AX6000
U-Boot flash instructions:
0. OpenWrt U-Boot does not support stock layout, it comes with recovery
boot support, automatic tftp recovery and never blocks UART.
A new flash layout is introduced, we call it OpenWrt U-Boot layout,
stock flash layout and the old OpenWrt layout are not supported.
During the whole flash procedure, please do not reboot or power off
unless requested explicitly, or you will break your device.
1. Your device should already running OpenWrt.
If not, follow the instructions to flash OpenWrt:
https://github.com/openwrt/openwrt/pull/11115
2. Backup BL2 Nvram Bdata Factory and FIP in case you break something or
in case you want to go back to stock firmware one day.
cat /dev/mtdblock0 > /tmp/BL2.bin
cat /dev/mtdblock1 > /tmp/Nvram.bin
cat /dev/mtdblock2 > /tmp/Bdata.bin
cat /dev/mtdblock3 > /tmp/Factory.bin
cat /dev/mtdblock4 > /tmp/FIP.bin
And save all whose bin files to somewhere safe.
Then backup your configurations, since ubiformat for entire mtd device is
required to create new ubootenv volume for OpenWrt U-Boot.
3. Run the following cmd to boot into an initramfs with the new OpenWrt
U-Boot layout that expand ubi partion to the end of flash:
ubiformat /dev/mtd7 -y -f /tmp/ax6000-ubootmod-initramfs-factory.ubi
4. After boot into initramfs, check mtd partion info.
The ubi partion should be mtd5
root@OpenWrt:~# cat /proc/mtd
dev: size erasesize name
mtd0: 00100000 00020000 BL2
mtd1: 00040000 00020000 Nvram
mtd2: 00040000 00020000 Bdata
mtd3: 00200000 00020000 Factory
mtd4: 00200000 00020000 FIP
mtd5: 07a80000 00020000 ubi
5. Load kmod-mtd-rw to temporarily make the bootloader partions writable.
The kmod-mtd-rw is from the feeds, it is not packed in initramfs-factory
by default.
To install kmod-mtd-rw via opkg:
opkg update && opkg install kmod-mtd-rw
Or, download kmod-mtd-rw.ipk from OpenWrt server and install it manually
e.g:
https://downloads.openwrt.org/snapshots/targets/mediatek/filogic/kmods/
Select your OpenWrt release version and kernel version accordingly.
Load kmod-mtd-rw:
insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1
6. Run the following cmd to clean all pending crash dumps in pstore,
or OpenWrt U-Boot may boot into NAND recovery or tftp recovery.
rm -f /sys/fs/pstore/*
7. Format ubi and create new ubootenv volume:
ubidetach -p /dev/mtd5; ubiformat /dev/mtd5 -y; ubiattach -p /dev/mtd5
ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
8. This is optional. Skip this if you do not want to have NAND recovery
boot feature offered by OpenWrt U-Boot. Don't worry, you always have
automatic tftp recovery feature enabled.
ubimkvol /dev/ubi0 -n 2 -N recovery -s 10MiB
ubiupdatevol /dev/ubi0_2 /tmp/ax6000-ubootmod-initramfs-recovery.itb
9. Now, flash new U-Boot. Bye-bye ugly stock U-Boot.
mtd write /tmp/ax6000-ubootmod-preloader.bin BL2
mtd write /tmp/ax6000-ubootmod-bl31-uboot.fip FIP
10. Flash the squashfs-sysupgrade.bin as usual:
sysupgrade -n /tmp/ax6000-ubootmod-squashfs-sysupgrade.itb
Enjoy!
Signed-off-by: Furong Xu <xfr@outlook.com>
2022-12-22 02:40:50 +00:00
|
|
|
xiaomi,redmi-router-ax6000-ubootmod)
|
|
|
|
|
. /lib/upgrade/nand.sh
|
|
|
|
|
local envubi=$(nand_find_ubi ubi)
|
|
|
|
|
local envdev=/dev/$(nand_find_volume $envubi ubootenv)
|
|
|
|
|
local envdev2=/dev/$(nand_find_volume $envubi ubootenv2)
|
|
|
|
|
ubootenv_add_uci_config "$envdev" "0x0" "0x1f000" "0x20000" "1"
|
|
|
|
|
ubootenv_add_uci_config "$envdev2" "0x0" "0x1f000" "0x20000" "1"
|
|
|
|
|
;;
|
2023-11-05 15:02:09 +00:00
|
|
|
glinet,gl-mt3000)
|
|
|
|
|
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x80000" "0x20000"
|
|
|
|
|
;;
|
|
|
|
|
glinet,gl-mt6000)
|
|
|
|
|
local envdev=$(find_mmc_part "u-boot-env")
|
|
|
|
|
ubootenv_add_uci_config "$envdev" "0x0" "0x80000"
|
|
|
|
|
;;
|
|
|
|
|
mercusys,mr90x-v1|\
|
|
|
|
|
routerich,ax3000)
|
|
|
|
|
local envdev=/dev/mtd$(find_mtd_index "u-boot-env")
|
|
|
|
|
ubootenv_add_uci_config "$envdev" "0x0" "0x20000" "0x20000" "1"
|
|
|
|
|
;;
|
|
|
|
|
ubnt,unifi-6-plus)
|
|
|
|
|
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x80000" "0x10000"
|
|
|
|
|
;;
|
|
|
|
|
xiaomi,mi-router-ax3000t|\
|
|
|
|
|
xiaomi,mi-router-wr30u-stock|\
|
|
|
|
|
xiaomi,redmi-router-ax6000-stock)
|
|
|
|
|
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x10000" "0x20000"
|
|
|
|
|
ubootenv_add_uci_sys_config "/dev/mtd2" "0x0" "0x10000" "0x20000"
|
|
|
|
|
;;
|
mediatek: add support for Zyxel EX5601-T0 router
Zyxel EX5601-T0 specifics
--------------
The operator specific firmware running on the Zyxel branded
EX5601-T0 includes U-Boot modifications affecting the OpenWrt
installation.
Partition Table
| dev | size | erasesize | name |
| ---- | -------- | --------- | ------------- |
| mtd0 | 20000000 | 00040000 | "spi0.1" |
| mtd1 | 00100000 | 00040000 | "BL2" |
| mtd2 | 00080000 | 00040000 | "u-boot-env" |
| mtd3 | 00200000 | 00040000 | "Factory" |
| mtd4 | 001c0000 | 00040000 | "FIP" |
| mtd5 | 00040000 | 00040000 | "zloader" |
| mtd6 | 04000000 | 00040000 | "ubi" |
| mtd7 | 04000000 | 00040000 | "ubi2" |
| mtd8 | 15a80000 | 00040000 | "zyubi" |
The router boots BL2 which than loads FIP (u-boot).
U-boot has hardcoded a command to always launch Zloader "mtd read zloader 0x46000000" and than "bootm". Bootargs are deactivated.
Zloader is the zyxel booloader which allow to dual-boot ubi or ubi2, by default access to zloader is blocked.
Too zloader checks that the firmware contains a particolar file called zyfwinfo.
Additional details regarding Zloader can be found here:
https://hack-gpon.github.io/zyxel/
https://forum.openwrt.org/t/adding-openwrt-support-for-zyxel-ex5601-t0/155914
Hardware
--------
SOC: MediaTek MT7986a
CPU: 4 core cortex-a53 (2000MHz)
RAM: 1GB DDR4
FLASH: 512MB SPI-NAND (Micron xxx)
WIFI: Wifi6 Mediatek MT7976 802.11ax 5 GHz 4x4 + 2.4GHZ 4x4
ETH: MediaTek MT7531 Switch + SoC
3 x builtin 1G phy (lan1, lan2, lan3)
1 x MaxLinear GPY211B 2.5 N-Base-T phy5 (lan4)
1 x MaxLinear GPY211B 2.5Gbit xor SFP/N-Base-T phy6 (wan)
USB: 1 x USB 3.2 Enhanced SuperSpeed port
UART: 3V3 115200 8N1 (Pinout: GND KEY RX TX VCC)
VOIP: 2 FXS ports for analog phones
MAC Address Table
-----------------
eth0/lan Factory 0x002a
eth1/wan Factory 0x0024
wifi 2.4Ghz Factory 0x0004
wifi 5Ghz Factory 0x0004 + 1
Serial console (UART)
---------------------
+-------+-------+-------+-------+-------+
| +3.3V | RX | TX | KEY | GND |
+---+---+-------+-------+-------+-------+
|
+--- Don't connect
Installation
------------
Keep in mind that openwrt can only run on the UBI partition, the openwrt firmware is not able to understand the zloader bootargs.
The procedure allows restoring the UBI partition with the Zyxel firmware and retains all the OEM functionalities.
1. Unlock Zloader (this will allow to swap manually between partitions UBI and UBI2):
- Attach a usb-ttl adapter to your computer and boot the router.
- While the router is booting at some point you will read the following: `Please press Enter to activate this console.`
- As soon as you read that press enter, type root and than press enter again (just do it, don't care about the logs scrolling).
- Most likely the router is still printing the boot log, leave it boot until it stops.
- If everything went ok you should have full root access "root@EX5601-T0:/#".
- Type the following command and press enter: "fw_setenv EngDebugFlag 0x1".
- Reboot the router.
- As soon as you read `Hit any key to stop autoboot:` press Enter.
- If everything went ok you should have the following prompt: "ZHAL>".
- You have successfully unlocked zloader access, this procedure must be done only once.
2. Check the current active partition:
- Boot the router and repeat the steps above to gain root access.
- Type the following command to check the current active image: "cat /proc/cmdline".
- If `rootubi=ubi` it means that the active partition is `mtd6`
- If `rootubi=ubi2` it means that the active partition is `mtd7`
- As mentioned earlier we need to flash openwrt into ubi/mtd6 and never overwrite ubi2/mtd7 to be able to fully roll-back.
- To activate and boot from mtd7 (ubi2) enter into ZHAL> command prompt and type the following commands:
atbt 1 # unlock write
atsw # swap boot partition
atsr # reboot the router
- After rebooting check again with "cat /proc/cmdline" that you are correctly booting from mtd7/ubi2
- If yes proceed with the installation guide. If not probably you don't have a firmware into ubi2 or you did something wrong.
3. Flashing:
- Download the sysupgrade file for the router from openwrt, than we need to add the zyfwinfo file into the sysupgrade tar.
Zloader only checks for the magic (which is a fixed value 'EXYZ') and the crc of the file itself (256bytes).
I created a script to create a valid zyfwinfo file but you can use anything that does exactly the same:
https://raw.githubusercontent.com/pameruoso/OpenWRT-Zyxel-EX5601-T0/main/gen_zyfwinfo.sh
- Add the zyfwinfo file into the sysupgrade tar.
- Enter via telnet or ssh into the router with admin credentials
- Enter the following commands to disable the firmware and model checks
"zycli fwidcheck off" and "zycli modelcheck off"
- Open the router web interface and in the update firmware page select the "restore default settings option"
- Select the sysupgrade file and click on upload.
- The router will flash and reboot itself into openwrt from UBI
4. Restoring and going back to Zyxel firmware.
- Use the ZHAL> command line to manually swap the boot parition to UBI2 with the following:
atbt 1 # unlock write
atsw # swap boot partition
atsr # reboot the router
- You will boot again the Zyxel firmware you have into UBI2 and you can flash the zyxel firmware to overwrite the UBI partition and openwrt.
Working features
----------------
3 gbit lan ports
Wifi
Zyxel partitioning for coexistance with Zloader and dual boot.
WAN SFP port (only after exporting pins 57 and 10. gpiobase411)
leds
reset button
serial interface
usb port
lan ethernet 2.5 gbit port (autosense)
wan ethernet 2.5 gbit port (autosense)
Not working
----------------
voip (missing drivers or proper zyxel platform software)
Swapping the wan ethernet/sfp xor port
----------------
The way to swap the wan port between sfp and ethernet is the following:
export the pins 57 and 10.
Pin 57 is used to probe if an sfp is present.
If pin 57 value is 0 it means that an sfp is present into the cage (cat /sys/class/gpio/gpio468/value).
If pin 57 value is 1 it means that no sfp is inserted into the cage.
In conclusion by default both 57 an 10 pins are by default 1, which means that the active port is the ethernet one.
After inserting an SFP pin 57 will become 0 and you have to manually change the value of pin 10 to 0 too.
This is totally scriptable of course.
Leds description
------------
All the leds are working out of the box but the leds managed by the 2 maxlinear phy (phy 5 lan, phy6 wan).
To activate the phy5 led (rj45 ethernet port led on the back of the router) you have to use mdio-tools.
To activate the phy6 led (led on the front of the router for 2.5gbit link) you have to use mdio-tools.
Example:
Set lan5 led to fast blink on 2500/1000, slow blink on 10/100:
mdio mdio-bus mmd 5:30 raw 0x0001 0x33FC
Set wan 2.5gbit led to constant on when wan is 2.5gbit:
mdio mdio-bus mmd 6:30 raw 0x0001 0x0080
Signed-off-by: Pietro Ameruoso <p.ameruoso@live.it>
(cherry picked from commit 1c05388ab04c934ec240e8362321908f91381a90)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-05-22 07:52:47 +00:00
|
|
|
zyxel,ex5601-t0)
|
|
|
|
|
local envdev=/dev/mtd$(find_mtd_index "u-boot-env")
|
|
|
|
|
ubootenv_add_uci_config "$envdev" "0x0" "0x20000" "0x40000" "2"
|
|
|
|
|
;;
|
2023-11-02 18:53:08 +00:00
|
|
|
zyxel,ex5601-t0-ubootmod)
|
|
|
|
|
. /lib/upgrade/nand.sh
|
|
|
|
|
local envubi=$(nand_find_ubi ubi)
|
|
|
|
|
local envdev=/dev/$(nand_find_volume $envubi ubootenv)
|
|
|
|
|
local envdev2=/dev/$(nand_find_volume $envubi ubootenv2)
|
|
|
|
|
ubootenv_add_uci_config "$envdev" "0x0" "0x1f000" "0x20000" "1"
|
|
|
|
|
ubootenv_add_uci_config "$envdev2" "0x0" "0x1f000" "0x20000" "1"
|
|
|
|
|
;;
|
filogic: support Telenor branded ZyXEL EX5700
Telenor quirks
--------------
The operator specific firmware running on the Telenor branded
ZyXEL EX5700 includes U-Boot modifications affecting the OpenWrt
installation.
Notable changes to U-Boot include
- environment is stored in RAM and reset to defaults when power
cycled
- dual partition scheme with "nomimal" or "rescue" systems, falling
back to "rescue" unless the OS signals success in 3 attempts
- several runtime additions to the device-tree
Some of these modifications have side effects requiring workarounds
- U-Boot modifies /chosen/bootargs in an unsafe manner, and will crash
unless this node exists
- U-Boot verifies that the selected rootfs UBI volume exists, and
refuses to boot if it doesn't. The chosen "rootfs" volume must contain
a squashfs signature even for tftp or initramfs booting.
- U-Boot parses the "factoryparams" UBI volume, setting the "ethaddr"
variable to the label mac. But "factoryparams" does not always
exist. Instead there is a "RIP" volume containing all the factory
data. Copying the "RIP" volume to "factoryparams" will fix this
Hardware
--------
SOC: MediaTek MT7986
RAM: 1GB DDR4
FLASH: 512MB SPI-NAND (Mikron xxx)
WIFI: Mediatek MT7986 802.11ax 5 GHz
Mediatek MT7916 DBDC 802.11ax 2.4 + 6 GHz
ETH: MediaTek MT7531 Switch + SoC
3 x builtin 1G phy (lan1, lan2, lan3)
2 x MaxLinear GPY211C 2.5 N-Base-T phy (lan4, wan)
USB: 1 x USB 3.2 Enhanced SuperSpeed port
UART: 3V3 115200 8N1 (Pinout: GND KEY RX TX VCC)
Installation
------------
1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
reachable at 192.168.1.2/24. Rename the image to C0A80101.img.
2. Connect the TFTP server to lan1, lan2 or lan3. Connect to the serial
console, Interrupt the autoboot process by pressing ESC when prompted.
3. Download and boot the OpenWrt initramfs image.
$ env set uboot_bootcount 0
$ env set firmware nominal
$ tftpboot
$ bootm
4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
Missing features
----------------
- The "lan1", "lan2" and "lan3" port LEDs are driven by the switch but
OpenWrt does not correctly configure the output.
- The "lan4" and "wan" port LEDs are driven by the GPH211C phys and
not configured by OpenWrt.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
(cherry picked from commit 6cc14bf66aa924962b926ea9702b6153ae418a7d)
2023-03-28 13:04:21 +00:00
|
|
|
zyxel,ex5700-telenor)
|
|
|
|
|
ubootenv_add_uci_config "/dev/ubootenv" "0x0" "0x4000" "0x4000" "1"
|
|
|
|
|
;;
|
2022-07-16 20:07:20 +00:00
|
|
|
esac
|
|
|
|
|
|
|
|
|
|
config_load ubootenv
|
mediatek: add Xiaomi Redmi Router AX6000 support
Hardware specification:
SoC: MediaTek MT7986A 4x A53
Flash: ESMT F50L1G41LB 128 MB
RAM: K4A4G165WF-BCWE 512 MB
Ethernet: 4x 10/100/1000 Mbps
WiFi1: MT7976GN 2.4GHz ax 4x4
WiFi2: MT7976AN 5GHz ax 4x4
Button: Mesh, Reset
Flash instructions:
1. Gain ssh and serial port access, see the link below:
https://openwrt.org/toh/xiaomi/redmi_ax6000#installation
2. Use ssh or serial port to log in to the router, and
execute the following command:
nvram set boot_wait=on
nvram set flag_boot_rootfs=0
nvram set flag_boot_success=1
nvram set flag_last_success=1
nvram set flag_try_sys1_failed=8
nvram set flag_try_sys2_failed=8
nvram commit
3. Set a static ip on the ethernet interface of your computer
(e.g. default: ip 192.168.31.100, gateway 192.168.31.1)
4. Download the initramfs image, rename it to initramfs.bin,
and host it with the tftp server.
5. Interrupt U-Boot and run these commands:
setenv mtdparts nmbm0:1024k(bl2),256k(Nvram),256k(Bdata),2048k(factory),2048k(fip),256k(crash),256k(crash_log),112640k(ubi)
saveenv
tftpboot initramfs.bin
bootm
6. After openwrt boots up, use scp or luci web
to upload sysupgrade.bin to upgrade.
Revert to stock firmware:
Restore mtdparts back to default, then use the
vendor's recovery tool (Windows only).
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2022-09-18 15:16:18 +00:00
|
|
|
config_foreach ubootenv_add_app_config
|
2022-07-16 20:07:20 +00:00
|
|
|
|
|
|
|
|
exit 0
|
