2021-01-17 05:54:04 +00:00
|
|
|
|
|
|
|
|
DEVICE_VARS += NETGEAR_BOARD_ID NETGEAR_HW_ID
|
|
|
|
|
DEVICE_VARS += RAS_BOARD RAS_ROOTFS_SIZE RAS_VERSION
|
|
|
|
|
DEVICE_VARS += WRGG_DEVNAME WRGG_SIGNATURE
|
|
|
|
|
|
|
|
|
|
define Device/FitImage
|
2022-11-17 02:03:59 +00:00
|
|
|
KERNEL_SUFFIX := -uImage.itb
|
2022-08-25 18:26:11 +00:00
|
|
|
KERNEL = kernel-bin | gzip | fit gzip $$(KDIR)/image-$$(DEVICE_DTS).dtb
|
2021-01-17 05:54:04 +00:00
|
|
|
KERNEL_NAME := Image
|
|
|
|
|
endef
|
|
|
|
|
|
|
|
|
|
define Device/FitImageLzma
|
2022-11-17 02:03:59 +00:00
|
|
|
KERNEL_SUFFIX := -uImage.itb
|
2022-08-25 18:26:11 +00:00
|
|
|
KERNEL = kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(DEVICE_DTS).dtb
|
2021-01-17 05:54:04 +00:00
|
|
|
KERNEL_NAME := Image
|
|
|
|
|
endef
|
|
|
|
|
|
|
|
|
|
define Device/FitzImage
|
2022-11-17 02:03:59 +00:00
|
|
|
KERNEL_SUFFIX := -zImage.itb
|
2022-08-25 18:26:11 +00:00
|
|
|
KERNEL = kernel-bin | fit none $$(KDIR)/image-$$(DEVICE_DTS).dtb
|
2021-01-17 05:54:04 +00:00
|
|
|
KERNEL_NAME := zImage
|
|
|
|
|
endef
|
|
|
|
|
|
|
|
|
|
define Device/UbiFit
|
|
|
|
|
KERNEL_IN_UBI := 1
|
2022-11-17 01:52:50 +00:00
|
|
|
IMAGES := factory.ubi sysupgrade.bin
|
|
|
|
|
IMAGE/factory.ubi := append-ubi
|
|
|
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
2021-01-17 05:54:04 +00:00
|
|
|
endef
|
|
|
|
|
|
|
|
|
|
define Device/DniImage
|
|
|
|
|
$(call Device/FitzImage)
|
|
|
|
|
NETGEAR_BOARD_ID :=
|
|
|
|
|
NETGEAR_HW_ID :=
|
|
|
|
|
IMAGES += factory.img
|
|
|
|
|
IMAGE/factory.img := append-kernel | pad-offset 64k 64 | append-uImage-fakehdr filesystem | append-rootfs | pad-rootfs | netgear-dni
|
|
|
|
|
IMAGE/sysupgrade.bin := append-kernel | pad-offset 64k 64 | append-uImage-fakehdr filesystem | \
|
2021-06-20 16:54:36 +00:00
|
|
|
append-rootfs | pad-rootfs | check-size | append-metadata
|
2021-01-17 05:54:04 +00:00
|
|
|
endef
|
|
|
|
|
|
|
|
|
|
define Build/append-rootfshdr
|
|
|
|
|
mkimage -A $(LINUX_KARCH) \
|
|
|
|
|
-O linux -T filesystem \
|
|
|
|
|
-C lzma -a $(KERNEL_LOADADDR) -e $(if $(KERNEL_ENTRY),$(KERNEL_ENTRY),$(KERNEL_LOADADDR)) \
|
|
|
|
|
-n root.squashfs -d $(IMAGE_ROOTFS) $@.new
|
2022-09-02 08:02:19 +00:00
|
|
|
cat $(IMAGE_KERNEL) > $@.$1
|
|
|
|
|
dd if=$@.new bs=64 count=1 >> $@.$1
|
2021-01-17 05:54:04 +00:00
|
|
|
endef
|
|
|
|
|
|
2021-07-15 19:48:11 +00:00
|
|
|
define Build/append-rutx-metadata
|
|
|
|
|
echo \
|
|
|
|
|
'{ \
|
|
|
|
|
"device_code": [".*"], \
|
|
|
|
|
"hwver": [".*"], \
|
|
|
|
|
"batch": [".*"], \
|
|
|
|
|
"serial": [".*"], \
|
|
|
|
|
"supported_devices":["teltonika,rutx"] \
|
|
|
|
|
}' | fwtool -I - $@
|
|
|
|
|
endef
|
|
|
|
|
|
2021-12-30 20:25:03 +00:00
|
|
|
define Build/copy-file
|
|
|
|
|
cat "$(1)" > "$@"
|
|
|
|
|
endef
|
|
|
|
|
|
2021-01-17 05:54:04 +00:00
|
|
|
define Build/mkmylofw_32m
|
|
|
|
|
$(eval device_id=$(word 1,$(1)))
|
|
|
|
|
$(eval revision=$(word 2,$(1)))
|
|
|
|
|
|
|
|
|
|
let \
|
|
|
|
|
size="$$(stat -c%s $@)" \
|
|
|
|
|
pad="$(subst k,* 1024,$(BLOCKSIZE))" \
|
|
|
|
|
pad="(pad - (size % pad)) % pad" \
|
|
|
|
|
newsize='size + pad'; \
|
|
|
|
|
$(STAGING_DIR_HOST)/bin/mkmylofw \
|
|
|
|
|
-B WPE72 -i 0x11f6:$(device_id):0x11f6:$(device_id) -r $(revision) \
|
|
|
|
|
-s 0x2000000 -p0x180000:$$newsize:al:0x80208000:"OpenWrt":$@ \
|
|
|
|
|
$@.new
|
|
|
|
|
@mv $@.new $@
|
|
|
|
|
endef
|
|
|
|
|
|
ipq40xx: add netgear wac510 support
This adds support for the Netgear WAC510 Insight Managed Smart Cloud
Wireless Access Point, an indoor dual-band, dual-radio 802.11ac
business-class wireless AP with integrated omnidirectional antennae
and two 10/100/1000 Mbps Ethernet ports.
For more information see:
<https://www.netgear.com/business/wifi/access-points/wac510>
Specifications:
SoC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 256 MiB
Flash1: 2 MiB Winbond W25Q16JV SPI-NOR
Flash2: 128 MiB Winbond W25N01GVZEIG SPI-NAND
Ethernet: Built-in IPQ4018 (SoC, QCA8072 PHY), 2x 1000/100/10 port,
WAN port active IEEE 802.3af/at PoE in
Wireless1: Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 3 dBi antennae
Wireless2: Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 4 dBi antennae
Input: (Optional) Barrel 12 V 2.5 A Power, Reset button SW1
LEDs: Power, Insight, WAN PoE, LAN, 2.4G WLAN, 5G WLAN
Serial: Header J2
1 - 3.3 Volt (Do NOT connect!)
2 - TX
3 - RX
4 - Ground
WARNING: The serial port needs a TTL/RS-232 3.3 volt level converter!
The Serial settings are 115200-8-N-1.
Installation via Stock Web Interface:
BTW: The default factory console/web interface login user/password are
admin/password.
In the web interface navigating to Management - Maintenance - Upgrade -
'Firmware Upgrade' will show you what is currently installed e.g.:
Manage Firmware
Current Firmware Version: V5.0.10.2
Backup Firmware Version: V1.2.5.11
Under 'Upgrade Options' choose Local (alternatively SFTP would be
available) then click/select 'Browse File' on the right side, choose
openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.tar
and hit the Upgrade button below. After a minute or two your browser
should indicate completion printing 'Firmware update complete.' and
'Rebooting AP...'.
Note that OpenWrt will use the WAN PoE port as actual WAN port
defaulting to DHCP client but NOT allowing LuCI access, use LAN port
defaulting to 192.168.1.1/24 to access LuCI.
Installation via TFTP Requiring Serial U-Boot Access:
Connect to the device's serial port and hit any key to stop autoboot.
Upload and boot the initramfs based OpenWrt image as follows:
(IPQ40xx) # setenv serverip 192.168.1.1
(IPQ40xx) # setenv ipaddr 192.168.1.2
(IPQ40xx) # tftpboot openwrt-ipq40xx-generic-netgear_wac510-initramfs-fit-uImage.itb
(IPQ40xx) # bootm
Note: This only runs OpenWrt from RAM and has not installed anything
to flash as of yet. One may permanently install OpenWrt as follows:
Check the MTD device number of the active partition:
root@OpenWrt:/# dmesg | grep 'set to be root filesystem'
[ 1.010084] mtd: device 9 (rootfs) set to be root filesystem
Upload the factory image ending with .ubi to /tmp (e.g. using scp or
tftp). Then flash the image as follows (substituting the 9 in mtd9
below with whatever number reported above):
root@OpenWrt:/# ubiformat /dev/mtd9 -f /tmp/openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.ubi
And reboot.
Dual Image Configuration:
The default U-Boot boot command bootipq uses the U-Boot environment
variables primary/secondary to decide which image to boot. E.g.
primary=0, secondary=3800000 uses rootfs while primary=3800000,
secondary=0 uses rootfs_1.
Switching their values changes the active partition. E.g. from within
U-Boot:
(IPQ40xx) # setenv primary 0
(IPQ40xx) # setenv secondary 3800000
(IPQ40xx) # saveenv
Or from a OpenWrt userspace serial/SSH console:
fw_setenv primary 0
fw_setenv secondary 3800000
Note that if you install two copies of OpenWrt then each will have its
independent configuration not like when switching partitions on the
stock firmware.
BTW: The kernel log shows which boot partition is active:
[ 2.439050] ubi0: attached mtd9 (name "rootfs", size 56 MiB)
vs.
[ 2.978785] ubi0: attached mtd10 (name "rootfs_1", size 56 MiB)
Note: After 3 failed boot attempts it automatically switches partition.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
[squashed netgear-tar commit into main and rename netgear-tar for
now, until it is made generic.]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-11-25 13:23:58 +00:00
|
|
|
define Build/wac5xx-netgear-tar
|
|
|
|
|
mkdir $@.tmp
|
|
|
|
|
mv $@ $@.tmp/wac5xx-ubifs-root.img
|
|
|
|
|
md5sum $@.tmp/wac5xx-ubifs-root.img > $@.tmp/wac5xx-ubifs-root.md5sum
|
|
|
|
|
echo "WAC505 WAC510" > $@.tmp/metadata.txt
|
|
|
|
|
echo "WAC505_V9.9.9.9" > $@.tmp/version
|
|
|
|
|
tar -C $@.tmp/ -cf $@ .
|
|
|
|
|
rm -rf $@.tmp
|
|
|
|
|
endef
|
|
|
|
|
|
2021-01-17 05:54:04 +00:00
|
|
|
define Build/qsdk-ipq-factory-nand-askey
|
|
|
|
|
$(TOPDIR)/scripts/mkits-qsdk-ipq-image.sh $@.its\
|
2022-09-02 08:02:19 +00:00
|
|
|
askey_kernel $@.$1 \
|
2021-01-17 05:54:04 +00:00
|
|
|
askey_fs $(IMAGE_ROOTFS) \
|
|
|
|
|
ubifs $@
|
|
|
|
|
PATH=$(LINUX_DIR)/scripts/dtc:$(PATH) mkimage -f $@.its $@.new
|
|
|
|
|
@mv $@.new $@
|
|
|
|
|
endef
|
|
|
|
|
|
ipq40xx: add support for GL.iNet GL-B2200
This patch adds supports for the GL-B2200 router.
Specifications:
- SOC: Qualcomm IPQ4019 ARM Quad-Core
- RAM: 512 MiB
- Flash: 16 MiB NOR - SPI0
- EMMC: 8GB EMMC
- ETH: Qualcomm QCA8075
- WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11b/g/n 2x2
- WLAN2: Qualcomm Atheros QCA4019 5GHz 802.11n/ac W2 2x2
- WLAN3: Qualcomm Atheros QCA9886 5GHz 802.11n/ac W2 2x2
- INPUT: Reset, WPS
- LED: Power, Internet
- UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1
- UART2: On board with BLE module
- SPI1: On board socket for Zigbee module
Update firmware instructions:
Please update the firmware via U-Boot web UI (by default at 192.168.1.1, following instructions found at
https://docs.gl-inet.com/en/3/troubleshooting/debrick/).
Normal sysupgrade, either via CLI or LuCI, is not possible from stock firmware.
Please do use the *gl-b2200-squashfs-emmc.img file, gunzipping the produced *gl-b2200-squashfs-emmc.img.gz one first.
What's working:
- WiFi 2G, 5G
- WPA2/WPA3
Not tested:
- Bluetooth LE/Zigbee
Credits goes to the original authors of this patch.
V1->V2:
- updates *arm-boot-add-dts-files.patch correctly (sorry, my mistake)
- add uboot-envtools support
V2->V3:
- Li Zhang updated official patch to fix wrong MAC address on wlan0 (PCI) interface
V3->V4:
- wire up sysupgrade
Signed-off-by: Li Zhang <li.zhang@gl-inet.com>
[fix tab and trailing space, document what's working and what's not]
Signed-off-by: TruongSinh Tran-Nguyen <i@truongsinh.pro>
[rebase on top of master, address remaining comments]
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
[remove redundant check in platform.sh]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-01 15:18:17 +00:00
|
|
|
define Build/qsdk-ipq-app-gpt
|
|
|
|
|
cp $@ $@.tmp 2>/dev/null || true
|
|
|
|
|
ptgen -g -o $@.tmp -a 1 -l 1024 \
|
|
|
|
|
-t 0x2e -N 0:HLOS -r -p 32M \
|
|
|
|
|
-t 0x83 -N rootfs -r -p 128M \
|
|
|
|
|
-N rootfs_data -p 512M
|
|
|
|
|
cat $@.tmp >> $@
|
|
|
|
|
rm $@.tmp
|
|
|
|
|
endef
|
|
|
|
|
|
2021-01-17 05:54:04 +00:00
|
|
|
define Build/SenaoFW
|
|
|
|
|
-$(STAGING_DIR_HOST)/bin/mksenaofw \
|
|
|
|
|
-n $(BOARD_NAME) -r $(VENDOR_ID) -p $(1) \
|
|
|
|
|
-c $(DATECODE) -w $(2) -x $(CW_VER) -t 0 \
|
|
|
|
|
-e $@ \
|
|
|
|
|
-o $@.new
|
|
|
|
|
@cp $@.new $@
|
|
|
|
|
endef
|
|
|
|
|
|
|
|
|
|
define Build/wrgg-image
|
|
|
|
|
mkwrggimg -i $@ \
|
|
|
|
|
-o $@.new \
|
|
|
|
|
-d "$(WRGG_DEVNAME)" \
|
|
|
|
|
-s "$(WRGG_SIGNATURE)" \
|
|
|
|
|
-v "" -m "" -B ""
|
|
|
|
|
mv $@.new $@
|
|
|
|
|
endef
|
|
|
|
|
|
|
|
|
|
define Device/8dev_habanero-dvk
|
|
|
|
|
$(call Device/FitImageLzma)
|
|
|
|
|
DEVICE_VENDOR := 8devices
|
|
|
|
|
DEVICE_MODEL := Habanero DVK
|
|
|
|
|
IMAGE_SIZE := 30976k
|
|
|
|
|
SOC := qcom-ipq4019
|
2021-06-20 16:54:36 +00:00
|
|
|
IMAGE/sysupgrade.bin := append-kernel | pad-to 64k | append-rootfs | pad-rootfs | check-size | append-metadata
|
2021-01-17 05:54:04 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += 8dev_habanero-dvk
|
|
|
|
|
|
|
|
|
|
define Device/8dev_jalapeno-common
|
|
|
|
|
$(call Device/FitImage)
|
|
|
|
|
$(call Device/UbiFit)
|
|
|
|
|
BLOCKSIZE := 128k
|
|
|
|
|
PAGESIZE := 2048
|
|
|
|
|
SOC := qcom-ipq4018
|
|
|
|
|
endef
|
|
|
|
|
|
|
|
|
|
define Device/8dev_jalapeno
|
|
|
|
|
$(call Device/8dev_jalapeno-common)
|
|
|
|
|
DEVICE_VENDOR := 8devices
|
|
|
|
|
DEVICE_MODEL := Jalapeno
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += 8dev_jalapeno
|
|
|
|
|
|
|
|
|
|
define Device/alfa-network_ap120c-ac
|
|
|
|
|
$(call Device/FitImage)
|
|
|
|
|
$(call Device/UbiFit)
|
|
|
|
|
DEVICE_VENDOR := ALFA Network
|
|
|
|
|
DEVICE_MODEL := AP120C-AC
|
|
|
|
|
SOC := qcom-ipq4018
|
2021-05-25 13:26:06 +00:00
|
|
|
DEVICE_PACKAGES := kmod-usb-acm kmod-tpm-i2c-atmel
|
2021-01-17 05:54:04 +00:00
|
|
|
BLOCKSIZE := 128k
|
|
|
|
|
PAGESIZE := 2048
|
|
|
|
|
IMAGE_SIZE := 65536k
|
2022-11-17 01:52:50 +00:00
|
|
|
IMAGES := factory.bin sysupgrade.bin
|
|
|
|
|
IMAGE/factory.bin := append-ubi | qsdk-ipq-factory-nand
|
2021-01-17 05:54:04 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += alfa-network_ap120c-ac
|
|
|
|
|
|
|
|
|
|
define Device/aruba_glenmorangie
|
|
|
|
|
$(call Device/FitImageLzma)
|
|
|
|
|
DEVICE_VENDOR := Aruba
|
|
|
|
|
SOC := qcom-ipq4029
|
|
|
|
|
endef
|
|
|
|
|
|
|
|
|
|
define Device/aruba_ap-303
|
|
|
|
|
$(call Device/aruba_glenmorangie)
|
|
|
|
|
DEVICE_MODEL := AP-303
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += aruba_ap-303
|
|
|
|
|
|
|
|
|
|
define Device/aruba_ap-303h
|
|
|
|
|
$(call Device/aruba_glenmorangie)
|
|
|
|
|
DEVICE_MODEL := AP-303H
|
|
|
|
|
endef
|
2022-12-21 09:34:03 +00:00
|
|
|
TARGET_DEVICES += aruba_ap-303h
|
2021-01-17 05:54:04 +00:00
|
|
|
|
|
|
|
|
define Device/aruba_ap-365
|
|
|
|
|
$(call Device/aruba_glenmorangie)
|
|
|
|
|
DEVICE_MODEL := AP-365
|
2023-05-17 20:02:40 +00:00
|
|
|
DEVICE_PACKAGES := kmod-hwmon-ad7418
|
2021-01-17 05:54:04 +00:00
|
|
|
endef
|
2023-04-12 20:06:18 +00:00
|
|
|
TARGET_DEVICES += aruba_ap-365
|
2021-01-17 05:54:04 +00:00
|
|
|
|
|
|
|
|
define Device/asus_map-ac2200
|
|
|
|
|
$(call Device/FitImageLzma)
|
|
|
|
|
DEVICE_VENDOR := ASUS
|
|
|
|
|
DEVICE_MODEL := Lyra (MAP-AC2200)
|
|
|
|
|
SOC := qcom-ipq4019
|
|
|
|
|
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct kmod-ath3k
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += asus_map-ac2200
|
|
|
|
|
|
2021-12-30 20:25:03 +00:00
|
|
|
# WARNING: this is an initramfs image that gets you half of the way there
|
|
|
|
|
# you need to delete the jffs2 ubi volume and sysupgrade to the final image
|
|
|
|
|
# to get a "trx" you can flash via web UI for ac42u/ac58u:
|
|
|
|
|
# - change call Device/FitImageLzma to Device/FitImage
|
|
|
|
|
# - add the following below UIMAGE_NAME
|
|
|
|
|
# UIMAGE_MAGIC := 0x27051956
|
|
|
|
|
# IMAGES += factory.trx
|
|
|
|
|
# IMAGE/factory.trx := copy-file $(KDIR)/tmp/$$(KERNEL_INITRAMFS_IMAGE) | uImage none
|
|
|
|
|
define Device/asus_rt-ac42u
|
|
|
|
|
$(call Device/FitImageLzma)
|
|
|
|
|
DEVICE_VENDOR := ASUS
|
|
|
|
|
DEVICE_MODEL := RT-AC42U
|
|
|
|
|
DEVICE_ALT0_VENDOR := ASUS
|
|
|
|
|
DEVICE_ALT0_MODEL := RT-ACRH17
|
2022-04-04 02:29:18 +00:00
|
|
|
DEVICE_ALT1_VENDOR := ASUS
|
|
|
|
|
DEVICE_ALT1_MODEL := RT-AC2200
|
2021-12-30 20:25:03 +00:00
|
|
|
SOC := qcom-ipq4019
|
|
|
|
|
BLOCKSIZE := 128k
|
|
|
|
|
PAGESIZE := 2048
|
|
|
|
|
IMAGE_SIZE := 20439364
|
|
|
|
|
FILESYSTEMS := squashfs
|
|
|
|
|
# RT-AC82U is nowhere to be found online
|
|
|
|
|
# Rather, this device is a/k/a RT-AC42U
|
|
|
|
|
# But we'll go with what the vendor firmware has...
|
|
|
|
|
UIMAGE_NAME:=$(shell echo -e '\03\01\01\01RT-AC82U')
|
2022-05-13 20:25:36 +00:00
|
|
|
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct kmod-usb-ledtrig-usbport
|
2021-12-30 20:25:03 +00:00
|
|
|
endef
|
2022-10-03 01:41:31 +00:00
|
|
|
TARGET_DEVICES += asus_rt-ac42u
|
2021-12-30 20:25:03 +00:00
|
|
|
|
2021-01-17 05:54:04 +00:00
|
|
|
define Device/asus_rt-ac58u
|
|
|
|
|
$(call Device/FitImageLzma)
|
|
|
|
|
DEVICE_VENDOR := ASUS
|
|
|
|
|
DEVICE_MODEL := RT-AC58U
|
2022-01-15 16:23:49 +00:00
|
|
|
DEVICE_ALT0_VENDOR := ASUS
|
|
|
|
|
DEVICE_ALT0_MODEL := RT-ACRH13
|
2021-01-17 05:54:04 +00:00
|
|
|
SOC := qcom-ipq4018
|
|
|
|
|
BLOCKSIZE := 128k
|
|
|
|
|
PAGESIZE := 2048
|
|
|
|
|
IMAGE_SIZE := 20439364
|
|
|
|
|
FILESYSTEMS := squashfs
|
|
|
|
|
# Someone - in their infinite wisdom - decided to put the firmware
|
|
|
|
|
# version in front of the image name \03\00\00\04 => Version 3.0.0.4
|
|
|
|
|
# Since u-boot works with strings we either need another fixup step
|
|
|
|
|
# to add a version... or we are very careful not to add '\0' into that
|
|
|
|
|
# string and call it a day.... Yeah, we do the latter!
|
|
|
|
|
UIMAGE_NAME:=$(shell echo -e '\03\01\01\01RT-AC58U')
|
|
|
|
|
DEVICE_PACKAGES := -kmod-ath10k-ct kmod-ath10k-ct-smallbuffers \
|
|
|
|
|
kmod-usb-ledtrig-usbport
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += asus_rt-ac58u
|
|
|
|
|
|
|
|
|
|
define Device/avm_fritzbox-4040
|
|
|
|
|
$(call Device/FitImageLzma)
|
|
|
|
|
DEVICE_VENDOR := AVM
|
|
|
|
|
DEVICE_MODEL := FRITZ!Box 4040
|
|
|
|
|
SOC := qcom-ipq4018
|
|
|
|
|
BOARD_NAME := fritz4040
|
|
|
|
|
IMAGE_SIZE := 29056k
|
|
|
|
|
UBOOT_PATH := $(STAGING_DIR_IMAGE)/uboot-fritz4040.bin
|
|
|
|
|
UBOOT_PARTITION_SIZE := 524288
|
|
|
|
|
IMAGES += eva.bin
|
|
|
|
|
IMAGE/eva.bin := append-uboot | pad-to $$$$(UBOOT_PARTITION_SIZE) | append-kernel | append-rootfs | pad-rootfs
|
2021-06-20 16:54:36 +00:00
|
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | check-size | append-metadata
|
2021-01-17 05:54:04 +00:00
|
|
|
DEVICE_PACKAGES := fritz-tffs fritz-caldata
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += avm_fritzbox-4040
|
|
|
|
|
|
|
|
|
|
define Device/avm_fritzbox-7530
|
|
|
|
|
$(call Device/FitImageLzma)
|
|
|
|
|
DEVICE_VENDOR := AVM
|
|
|
|
|
DEVICE_MODEL := FRITZ!Box 7530
|
2021-12-05 11:14:45 +00:00
|
|
|
DEVICE_ALT0_VENDOR := AVM
|
|
|
|
|
DEVICE_ALT0_MODEL := FRITZ!Box 7520
|
2021-01-17 05:54:04 +00:00
|
|
|
SOC := qcom-ipq4019
|
2019-08-21 07:10:46 +00:00
|
|
|
DEVICE_PACKAGES := fritz-caldata fritz-tffs-nand ltq-vdsl-vr11-app
|
2021-01-17 05:54:04 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += avm_fritzbox-7530
|
|
|
|
|
|
|
|
|
|
define Device/avm_fritzrepeater-1200
|
|
|
|
|
$(call Device/FitImageLzma)
|
|
|
|
|
DEVICE_VENDOR := AVM
|
|
|
|
|
DEVICE_MODEL := FRITZ!Repeater 1200
|
|
|
|
|
SOC := qcom-ipq4019
|
2022-05-13 20:25:36 +00:00
|
|
|
DEVICE_PACKAGES := fritz-caldata fritz-tffs-nand
|
2021-01-17 05:54:04 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += avm_fritzrepeater-1200
|
|
|
|
|
|
|
|
|
|
define Device/avm_fritzrepeater-3000
|
|
|
|
|
$(call Device/FitImageLzma)
|
|
|
|
|
DEVICE_VENDOR := AVM
|
|
|
|
|
DEVICE_MODEL := FRITZ!Repeater 3000
|
|
|
|
|
SOC := qcom-ipq4019
|
|
|
|
|
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct fritz-caldata fritz-tffs-nand
|
|
|
|
|
endef
|
2023-04-24 20:00:18 +00:00
|
|
|
TARGET_DEVICES += avm_fritzrepeater-3000
|
2021-01-17 05:54:04 +00:00
|
|
|
|
|
|
|
|
define Device/buffalo_wtr-m2133hp
|
|
|
|
|
$(call Device/FitImage)
|
|
|
|
|
$(call Device/UbiFit)
|
|
|
|
|
DEVICE_VENDOR := Buffalo
|
|
|
|
|
DEVICE_MODEL := WTR-M2133HP
|
|
|
|
|
SOC := qcom-ipq4019
|
2022-05-13 20:25:36 +00:00
|
|
|
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct
|
2021-01-17 05:54:04 +00:00
|
|
|
BLOCKSIZE := 128k
|
|
|
|
|
PAGESIZE := 2048
|
|
|
|
|
endef
|
2023-05-31 07:41:59 +00:00
|
|
|
TARGET_DEVICES += buffalo_wtr-m2133hp
|
2021-01-17 05:54:04 +00:00
|
|
|
|
|
|
|
|
define Device/cellc_rtl30vw
|
2022-11-17 02:03:59 +00:00
|
|
|
KERNEL_SUFFIX := -zImage.itb
|
2022-08-25 18:26:11 +00:00
|
|
|
KERNEL_INITRAMFS = kernel-bin | gzip | fit gzip $$(KDIR)/image-$$(DEVICE_DTS).dtb
|
|
|
|
|
KERNEL = kernel-bin | fit none $$(KDIR)/image-$$(DEVICE_DTS).dtb | uImage lzma | pad-to 2048
|
2021-11-05 15:01:54 +00:00
|
|
|
KERNEL_NAME := zImage
|
2021-01-17 05:54:04 +00:00
|
|
|
KERNEL_IN_UBI :=
|
2022-11-17 01:52:50 +00:00
|
|
|
IMAGES := factory.bin sysupgrade.bin
|
|
|
|
|
IMAGE/factory.bin := append-rootfshdr kernel | append-ubi | qsdk-ipq-factory-nand-askey kernel
|
|
|
|
|
IMAGE/sysupgrade.bin := append-rootfshdr kernel | sysupgrade-tar kernel=$$$$@.kernel | append-metadata
|
2021-01-17 05:54:04 +00:00
|
|
|
DEVICE_VENDOR := Cell C
|
|
|
|
|
DEVICE_MODEL := RTL30VW
|
|
|
|
|
SOC := qcom-ipq4019
|
|
|
|
|
DEVICE_DTS_CONFIG := config@5
|
|
|
|
|
KERNEL_INSTALL := 1
|
|
|
|
|
KERNEL_SIZE := 4096k
|
|
|
|
|
IMAGE_SIZE := 57344k
|
|
|
|
|
BLOCKSIZE := 128k
|
|
|
|
|
PAGESIZE := 2048
|
2022-05-13 20:25:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-usb-net-qmi-wwan kmod-usb-serial-option uqmi
|
2021-01-17 05:54:04 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += cellc_rtl30vw
|
|
|
|
|
|
|
|
|
|
define Device/cilab_meshpoint-one
|
|
|
|
|
$(call Device/8dev_jalapeno-common)
|
|
|
|
|
DEVICE_VENDOR := Crisis Innovation Lab
|
|
|
|
|
DEVICE_MODEL := MeshPoint.One
|
2023-03-15 07:50:06 +00:00
|
|
|
DEVICE_PACKAGES += kmod-i2c-gpio kmod-iio-bmp280-i2c kmod-hwmon-ina2xx kmod-rtc-pcf2127
|
2021-01-17 05:54:04 +00:00
|
|
|
endef
|
2022-09-28 15:42:48 +00:00
|
|
|
# Missing DSA Setup
|
|
|
|
|
#TARGET_DEVICES += cilab_meshpoint-one
|
2021-01-17 05:54:04 +00:00
|
|
|
|
|
|
|
|
define Device/compex_wpj419
|
|
|
|
|
$(call Device/FitImage)
|
|
|
|
|
$(call Device/UbiFit)
|
|
|
|
|
DEVICE_VENDOR := Compex
|
|
|
|
|
DEVICE_MODEL := WPJ419
|
|
|
|
|
SOC := qcom-ipq4019
|
|
|
|
|
DEVICE_DTS_CONFIG := config@12
|
|
|
|
|
KERNEL_INSTALL := 1
|
|
|
|
|
BLOCKSIZE := 128k
|
|
|
|
|
PAGESIZE := 2048
|
|
|
|
|
FILESYSTEMS := squashfs
|
|
|
|
|
endef
|
2022-09-28 15:42:48 +00:00
|
|
|
# Missing DSA Setup
|
|
|
|
|
#TARGET_DEVICES += compex_wpj419
|
2021-01-17 05:54:04 +00:00
|
|
|
|
|
|
|
|
define Device/compex_wpj428
|
|
|
|
|
$(call Device/FitImage)
|
|
|
|
|
DEVICE_VENDOR := Compex
|
|
|
|
|
DEVICE_MODEL := WPJ428
|
|
|
|
|
SOC := qcom-ipq4028
|
|
|
|
|
DEVICE_DTS_CONFIG := config@4
|
|
|
|
|
BLOCKSIZE := 64k
|
|
|
|
|
IMAGE_SIZE := 31232k
|
|
|
|
|
KERNEL_SIZE := 4096k
|
|
|
|
|
IMAGES += cpximg-6a04.bin
|
|
|
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
|
|
|
|
IMAGE/cpximg-6a04.bin := append-kernel | append-rootfs | pad-rootfs | mkmylofw_32m 0x8A2 3
|
|
|
|
|
DEVICE_PACKAGES := kmod-gpio-beeper
|
2021-11-03 15:45:38 +00:00
|
|
|
DEFAULT := n
|
2021-01-17 05:54:04 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += compex_wpj428
|
|
|
|
|
|
|
|
|
|
define Device/devolo_magic-2-wifi-next
|
|
|
|
|
$(call Device/FitImage)
|
|
|
|
|
DEVICE_VENDOR := devolo
|
|
|
|
|
DEVICE_MODEL := Magic 2 WiFi next
|
|
|
|
|
SOC := qcom-ipq4018
|
|
|
|
|
KERNEL_SIZE := 4096k
|
|
|
|
|
|
|
|
|
|
# If the bootloader sees 0xDEADC0DE and this trailer at the 64k boundary of a TFTP image
|
|
|
|
|
# it will bootm it, just like we want for the initramfs.
|
2022-08-25 18:26:11 +00:00
|
|
|
KERNEL_INITRAMFS := kernel-bin | gzip | fit gzip $$(KDIR)/image-$$(DEVICE_DTS).dtb | pad-to 64k |\
|
2021-01-17 05:54:04 +00:00
|
|
|
append-string -e '\xDE\xAD\xC0\xDE{"fl_initramfs":""}\x00'
|
|
|
|
|
|
|
|
|
|
IMAGE_SIZE := 26624k
|
|
|
|
|
IMAGES := sysupgrade.bin
|
|
|
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
2021-11-03 15:45:38 +00:00
|
|
|
DEFAULT := n
|
2021-01-17 05:54:04 +00:00
|
|
|
endef
|
2022-09-28 15:42:48 +00:00
|
|
|
# Missing DSA Setup
|
|
|
|
|
#TARGET_DEVICES += devolo_magic-2-wifi-next
|
2021-01-17 05:54:04 +00:00
|
|
|
|
|
|
|
|
define Device/dlink_dap-2610
|
|
|
|
|
$(call Device/FitImageLzma)
|
|
|
|
|
DEVICE_VENDOR := D-Link
|
|
|
|
|
DEVICE_MODEL := DAP-2610
|
|
|
|
|
SOC := qcom-ipq4018
|
|
|
|
|
DEVICE_DTS_CONFIG := config@ap.dk01.1-c1
|
|
|
|
|
BLOCKSIZE := 64k
|
|
|
|
|
WRGG_DEVNAME := /dev/mtdblock/8
|
|
|
|
|
WRGG_SIGNATURE := wapac30_dkbs_dap2610
|
|
|
|
|
IMAGE_SIZE := 14080k
|
|
|
|
|
IMAGES += factory.bin
|
|
|
|
|
# Bootloader expects a special 160 byte header which is added by
|
|
|
|
|
# wrgg-image.
|
|
|
|
|
# Factory image size must be larger than 6MB, and size in wrgg header must
|
|
|
|
|
# match actual factory image size to be flashable from D-Link http server.
|
|
|
|
|
# Bootloader verifies checksum of wrgg image before booting, thus jffs2
|
|
|
|
|
# cannot be part of the wrgg image. This is solved in the factory image by
|
|
|
|
|
# having the rootfs at the end of the image (without pad-rootfs). And in
|
|
|
|
|
# the sysupgrade image only the kernel is included in the wrgg checksum,
|
|
|
|
|
# but this is not flashable from the D-link http server.
|
|
|
|
|
# append-rootfs must start on an erase block boundary.
|
|
|
|
|
IMAGE/factory.bin := append-kernel | pad-offset 6144k 160 | append-rootfs | wrgg-image | check-size
|
|
|
|
|
IMAGE/sysupgrade.bin := append-kernel | wrgg-image | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | check-size | append-metadata
|
|
|
|
|
endef
|
2022-11-09 05:52:18 +00:00
|
|
|
TARGET_DEVICES += dlink_dap-2610
|
2021-01-17 05:54:04 +00:00
|
|
|
|
|
|
|
|
define Device/edgecore_ecw5211
|
|
|
|
|
$(call Device/FitImage)
|
|
|
|
|
$(call Device/UbiFit)
|
|
|
|
|
DEVICE_VENDOR := Edgecore
|
|
|
|
|
DEVICE_MODEL := ECW5211
|
|
|
|
|
SOC := qcom-ipq4018
|
|
|
|
|
BLOCKSIZE := 128k
|
|
|
|
|
PAGESIZE := 2048
|
2021-08-18 13:11:11 +00:00
|
|
|
DEVICE_DTS_CONFIG := config@ap.dk01.1-c2
|
2021-05-25 13:26:06 +00:00
|
|
|
DEVICE_PACKAGES := kmod-tpm-i2c-atmel kmod-usb-acm
|
2021-01-17 05:54:04 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += edgecore_ecw5211
|
|
|
|
|
|
|
|
|
|
define Device/edgecore_oap100
|
|
|
|
|
$(call Device/FitImage)
|
|
|
|
|
$(call Device/UbiFit)
|
|
|
|
|
DEVICE_VENDOR := Edgecore
|
|
|
|
|
DEVICE_MODEL := OAP100
|
|
|
|
|
SOC := qcom-ipq4019
|
|
|
|
|
BLOCKSIZE := 128k
|
|
|
|
|
PAGESIZE := 2048
|
2022-11-17 01:52:50 +00:00
|
|
|
IMAGES := sysupgrade.bin
|
2021-01-17 05:54:04 +00:00
|
|
|
DEVICE_DTS_CONFIG := config@ap.dk07.1-c1
|
2023-05-17 20:02:40 +00:00
|
|
|
DEVICE_PACKAGES := kmod-usb-acm kmod-usb-net kmod-usb-net-cdc-qmi uqmi
|
2021-01-17 05:54:04 +00:00
|
|
|
endef
|
2022-09-28 15:42:48 +00:00
|
|
|
# Missing DSA Setup
|
|
|
|
|
#TARGET_DEVICES += edgecore_oap100
|
2021-01-17 05:54:04 +00:00
|
|
|
|
|
|
|
|
define Device/engenius_eap1300
|
|
|
|
|
$(call Device/FitImage)
|
|
|
|
|
DEVICE_VENDOR := EnGenius
|
|
|
|
|
DEVICE_MODEL := EAP1300
|
|
|
|
|
DEVICE_DTS_CONFIG := config@4
|
|
|
|
|
BOARD_NAME := eap1300
|
|
|
|
|
SOC := qcom-ipq4018
|
|
|
|
|
KERNEL_SIZE := 5120k
|
|
|
|
|
IMAGE_SIZE := 25344k
|
|
|
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
|
|
|
|
endef
|
2022-09-28 15:42:48 +00:00
|
|
|
# Missing DSA Setup
|
|
|
|
|
#TARGET_DEVICES += engenius_eap1300
|
2021-01-17 05:54:04 +00:00
|
|
|
|
|
|
|
|
define Device/engenius_eap2200
|
|
|
|
|
$(call Device/FitImage)
|
|
|
|
|
$(call Device/UbiFit)
|
|
|
|
|
DEVICE_VENDOR := EnGenius
|
|
|
|
|
DEVICE_MODEL := EAP2200
|
|
|
|
|
SOC := qcom-ipq4019
|
|
|
|
|
BLOCKSIZE := 128k
|
|
|
|
|
PAGESIZE := 2048
|
2022-05-13 20:25:36 +00:00
|
|
|
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct -kmod-ath10k-ct kmod-ath10k-ct-smallbuffers
|
2021-01-17 05:54:04 +00:00
|
|
|
endef
|
2022-09-28 15:42:48 +00:00
|
|
|
# Missing DSA Setup
|
|
|
|
|
#TARGET_DEVICES += engenius_eap2200
|
2021-01-17 05:54:04 +00:00
|
|
|
|
|
|
|
|
define Device/engenius_emd1
|
|
|
|
|
$(call Device/FitImage)
|
|
|
|
|
DEVICE_VENDOR := EnGenius
|
|
|
|
|
DEVICE_MODEL := EMD1
|
|
|
|
|
DEVICE_DTS_CONFIG := config@4
|
|
|
|
|
SOC := qcom-ipq4018
|
|
|
|
|
IMAGE_SIZE := 30720k
|
|
|
|
|
IMAGES += factory.bin
|
|
|
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
|
|
|
|
IMAGE/factory.bin := qsdk-ipq-factory-nor | check-size
|
|
|
|
|
endef
|
2022-09-28 15:42:48 +00:00
|
|
|
# Missing DSA Setup
|
|
|
|
|
#TARGET_DEVICES += engenius_emd1
|
2021-01-17 05:54:04 +00:00
|
|
|
|
|
|
|
|
define Device/engenius_emr3500
|
|
|
|
|
$(call Device/FitImage)
|
|
|
|
|
DEVICE_VENDOR := EnGenius
|
|
|
|
|
DEVICE_MODEL := EMR3500
|
|
|
|
|
DEVICE_DTS_CONFIG := config@4
|
|
|
|
|
SOC := qcom-ipq4018
|
|
|
|
|
KERNEL_SIZE := 4096k
|
|
|
|
|
IMAGE_SIZE := 30720k
|
|
|
|
|
IMAGES += factory.bin
|
|
|
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
|
|
|
|
IMAGE/factory.bin := qsdk-ipq-factory-nor | check-size
|
2021-11-03 15:45:38 +00:00
|
|
|
DEFAULT := n
|
2021-01-17 05:54:04 +00:00
|
|
|
endef
|
2022-09-28 15:42:48 +00:00
|
|
|
# Missing DSA Setup
|
|
|
|
|
#TARGET_DEVICES += engenius_emr3500
|
2021-01-17 05:54:04 +00:00
|
|
|
|
|
|
|
|
define Device/engenius_ens620ext
|
|
|
|
|
$(call Device/FitImage)
|
|
|
|
|
DEVICE_VENDOR := EnGenius
|
|
|
|
|
DEVICE_MODEL := ENS620EXT
|
|
|
|
|
SOC := qcom-ipq4018
|
|
|
|
|
DEVICE_DTS_CONFIG := config@4
|
|
|
|
|
BLOCKSIZE := 64k
|
|
|
|
|
PAGESIZE := 256
|
|
|
|
|
BOARD_NAME := ENS620EXT
|
|
|
|
|
VENDOR_ID := 0x0101
|
|
|
|
|
PRODUCT_ID := 0x79
|
|
|
|
|
PRODUCT_ID_NEW := 0xA4
|
|
|
|
|
DATECODE := 190507
|
|
|
|
|
FW_VER := 3.1.2
|
|
|
|
|
FW_VER_NEW := 3.5.6
|
|
|
|
|
CW_VER := 1.8.99
|
|
|
|
|
IMAGE_SIZE := 21312k
|
|
|
|
|
KERNEL_SIZE := 5120k
|
|
|
|
|
FILESYSTEMS := squashfs
|
|
|
|
|
IMAGES += factory_30.bin factory_35.bin
|
|
|
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | check-size | append-metadata
|
|
|
|
|
IMAGE/factory_30.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-rootfs | pad-rootfs | check-size | SenaoFW $$$$(PRODUCT_ID) $$$$(FW_VER)
|
|
|
|
|
IMAGE/factory_35.bin := qsdk-ipq-factory-nor | check-size | SenaoFW $$$$(PRODUCT_ID_NEW) $$$$(FW_VER_NEW)
|
|
|
|
|
endef
|
2022-09-28 15:42:48 +00:00
|
|
|
# Missing DSA Setup
|
|
|
|
|
#TARGET_DEVICES += engenius_ens620ext
|
2021-01-17 05:54:04 +00:00
|
|
|
|
2022-08-29 12:30:01 +00:00
|
|
|
define Device/extreme-networks_ws-ap3915i
|
|
|
|
|
$(call Device/FitImage)
|
|
|
|
|
DEVICE_VENDOR := Extreme Networks
|
|
|
|
|
DEVICE_MODEL := WS-AP3915i
|
|
|
|
|
IMAGE_SIZE := 30080k
|
|
|
|
|
SOC := qcom-ipq4029
|
|
|
|
|
BLOCKSIZE := 128k
|
|
|
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | check-size | append-metadata
|
|
|
|
|
endef
|
2023-01-17 07:02:02 +00:00
|
|
|
TARGET_DEVICES += extreme-networks_ws-ap3915i
|
2022-08-29 12:30:01 +00:00
|
|
|
|
2021-01-17 05:54:04 +00:00
|
|
|
define Device/ezviz_cs-w3-wd1200g-eup
|
|
|
|
|
$(call Device/FitImage)
|
|
|
|
|
DEVICE_VENDOR := EZVIZ
|
|
|
|
|
DEVICE_MODEL := CS-W3-WD1200G
|
|
|
|
|
DEVICE_VARIANT := EUP
|
|
|
|
|
IMAGE_SIZE := 14848k
|
2021-11-28 14:26:18 +00:00
|
|
|
KERNEL_SIZE = 6m
|
2021-01-17 05:54:04 +00:00
|
|
|
SOC := qcom-ipq4018
|
|
|
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | \
|
|
|
|
|
append-metadata
|
2022-05-13 20:25:36 +00:00
|
|
|
DEVICE_PACKAGES := -kmod-ath10k-ct kmod-ath10k-ct-smallbuffers
|
2021-11-28 14:26:18 +00:00
|
|
|
DEVICE_COMPAT_VERSION := 2.0
|
|
|
|
|
DEVICE_COMPAT_MESSAGE := uboot's bootcmd has to be updated (see wiki). \
|
|
|
|
|
Upgrade via sysupgrade mechanism is not possible.
|
2021-01-17 05:54:04 +00:00
|
|
|
endef
|
2023-05-18 20:51:08 +00:00
|
|
|
TARGET_DEVICES += ezviz_cs-w3-wd1200g-eup
|
2021-01-17 05:54:04 +00:00
|
|
|
|
2022-09-19 09:47:40 +00:00
|
|
|
define Device/glinet_gl-a1300
|
|
|
|
|
$(call Device/FitImage)
|
|
|
|
|
$(call Device/UbiFit)
|
|
|
|
|
DEVICE_VENDOR := GL.iNet
|
|
|
|
|
DEVICE_MODEL := GL-A1300
|
|
|
|
|
SOC := qcom-ipq4018
|
|
|
|
|
DEVICE_DTS_CONFIG := config@ap.dk01.1-c2
|
|
|
|
|
BLOCKSIZE := 128k
|
|
|
|
|
PAGESIZE := 2048
|
|
|
|
|
IMAGE_SIZE := 131072k
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += glinet_gl-a1300
|
|
|
|
|
|
2021-01-17 05:54:04 +00:00
|
|
|
define Device/glinet_gl-ap1300
|
|
|
|
|
$(call Device/FitImage)
|
|
|
|
|
$(call Device/UbiFit)
|
|
|
|
|
DEVICE_VENDOR := GL.iNet
|
|
|
|
|
DEVICE_MODEL := GL-AP1300
|
|
|
|
|
SOC := qcom-ipq4018
|
|
|
|
|
DEVICE_DTS_CONFIG := config@ap.dk01.1-c2
|
|
|
|
|
BLOCKSIZE := 128k
|
|
|
|
|
PAGESIZE := 2048
|
|
|
|
|
IMAGE_SIZE := 131072k
|
|
|
|
|
KERNEL_INSTALL := 1
|
2023-05-17 20:02:40 +00:00
|
|
|
DEVICE_PACKAGES := kmod-usb-net-qmi-wwan kmod-usb-serial-option uqmi
|
2021-01-17 05:54:04 +00:00
|
|
|
endef
|
2022-07-16 08:33:24 +00:00
|
|
|
TARGET_DEVICES += glinet_gl-ap1300
|
2021-01-17 05:54:04 +00:00
|
|
|
|
|
|
|
|
define Device/glinet_gl-b1300
|
2021-10-09 23:32:30 +00:00
|
|
|
$(call Device/FitzImage)
|
2021-01-17 05:54:04 +00:00
|
|
|
DEVICE_VENDOR := GL.iNet
|
|
|
|
|
DEVICE_MODEL := GL-B1300
|
|
|
|
|
BOARD_NAME := gl-b1300
|
|
|
|
|
SOC := qcom-ipq4029
|
|
|
|
|
KERNEL_SIZE := 4096k
|
|
|
|
|
IMAGE_SIZE := 26624k
|
|
|
|
|
IMAGE/sysupgrade.bin := append-kernel |append-rootfs | pad-rootfs | append-metadata
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += glinet_gl-b1300
|
|
|
|
|
|
ipq40xx: add support for GL.iNet GL-B2200
This patch adds supports for the GL-B2200 router.
Specifications:
- SOC: Qualcomm IPQ4019 ARM Quad-Core
- RAM: 512 MiB
- Flash: 16 MiB NOR - SPI0
- EMMC: 8GB EMMC
- ETH: Qualcomm QCA8075
- WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11b/g/n 2x2
- WLAN2: Qualcomm Atheros QCA4019 5GHz 802.11n/ac W2 2x2
- WLAN3: Qualcomm Atheros QCA9886 5GHz 802.11n/ac W2 2x2
- INPUT: Reset, WPS
- LED: Power, Internet
- UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1
- UART2: On board with BLE module
- SPI1: On board socket for Zigbee module
Update firmware instructions:
Please update the firmware via U-Boot web UI (by default at 192.168.1.1, following instructions found at
https://docs.gl-inet.com/en/3/troubleshooting/debrick/).
Normal sysupgrade, either via CLI or LuCI, is not possible from stock firmware.
Please do use the *gl-b2200-squashfs-emmc.img file, gunzipping the produced *gl-b2200-squashfs-emmc.img.gz one first.
What's working:
- WiFi 2G, 5G
- WPA2/WPA3
Not tested:
- Bluetooth LE/Zigbee
Credits goes to the original authors of this patch.
V1->V2:
- updates *arm-boot-add-dts-files.patch correctly (sorry, my mistake)
- add uboot-envtools support
V2->V3:
- Li Zhang updated official patch to fix wrong MAC address on wlan0 (PCI) interface
V3->V4:
- wire up sysupgrade
Signed-off-by: Li Zhang <li.zhang@gl-inet.com>
[fix tab and trailing space, document what's working and what's not]
Signed-off-by: TruongSinh Tran-Nguyen <i@truongsinh.pro>
[rebase on top of master, address remaining comments]
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
[remove redundant check in platform.sh]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-01 15:18:17 +00:00
|
|
|
define Device/glinet_gl-b2200
|
|
|
|
|
$(call Device/FitzImage)
|
|
|
|
|
DEVICE_VENDOR := GL.iNet
|
|
|
|
|
DEVICE_MODEL := GL-B2200
|
|
|
|
|
SOC := qcom-ipq4019
|
|
|
|
|
DEVICE_DTS_CONFIG := config@ap.dk04.1-c3
|
|
|
|
|
KERNEL_INITRAMFS_SUFFIX := -recovery.itb
|
|
|
|
|
IMAGES := emmc.img.gz sysupgrade.bin
|
|
|
|
|
IMAGE/emmc.img.gz := qsdk-ipq-app-gpt |\
|
|
|
|
|
pad-to 1024k | append-kernel |\
|
|
|
|
|
pad-to 33792k | append-rootfs |\
|
|
|
|
|
append-metadata | gzip
|
|
|
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
2022-06-26 13:05:27 +00:00
|
|
|
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct \
|
ipq40xx: add support for GL.iNet GL-B2200
This patch adds supports for the GL-B2200 router.
Specifications:
- SOC: Qualcomm IPQ4019 ARM Quad-Core
- RAM: 512 MiB
- Flash: 16 MiB NOR - SPI0
- EMMC: 8GB EMMC
- ETH: Qualcomm QCA8075
- WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11b/g/n 2x2
- WLAN2: Qualcomm Atheros QCA4019 5GHz 802.11n/ac W2 2x2
- WLAN3: Qualcomm Atheros QCA9886 5GHz 802.11n/ac W2 2x2
- INPUT: Reset, WPS
- LED: Power, Internet
- UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1
- UART2: On board with BLE module
- SPI1: On board socket for Zigbee module
Update firmware instructions:
Please update the firmware via U-Boot web UI (by default at 192.168.1.1, following instructions found at
https://docs.gl-inet.com/en/3/troubleshooting/debrick/).
Normal sysupgrade, either via CLI or LuCI, is not possible from stock firmware.
Please do use the *gl-b2200-squashfs-emmc.img file, gunzipping the produced *gl-b2200-squashfs-emmc.img.gz one first.
What's working:
- WiFi 2G, 5G
- WPA2/WPA3
Not tested:
- Bluetooth LE/Zigbee
Credits goes to the original authors of this patch.
V1->V2:
- updates *arm-boot-add-dts-files.patch correctly (sorry, my mistake)
- add uboot-envtools support
V2->V3:
- Li Zhang updated official patch to fix wrong MAC address on wlan0 (PCI) interface
V3->V4:
- wire up sysupgrade
Signed-off-by: Li Zhang <li.zhang@gl-inet.com>
[fix tab and trailing space, document what's working and what's not]
Signed-off-by: TruongSinh Tran-Nguyen <i@truongsinh.pro>
[rebase on top of master, address remaining comments]
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
[remove redundant check in platform.sh]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-01 15:18:17 +00:00
|
|
|
kmod-fs-ext4 kmod-mmc kmod-spi-dev mkf2fs e2fsprogs kmod-fs-f2fs
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += glinet_gl-b2200
|
|
|
|
|
|
2021-01-17 05:54:04 +00:00
|
|
|
define Device/glinet_gl-s1300
|
2021-10-09 23:32:30 +00:00
|
|
|
$(call Device/FitzImage)
|
2021-01-17 05:54:04 +00:00
|
|
|
DEVICE_VENDOR := GL.iNet
|
|
|
|
|
DEVICE_MODEL := GL-S1300
|
|
|
|
|
SOC := qcom-ipq4029
|
|
|
|
|
KERNEL_SIZE := 4096k
|
|
|
|
|
IMAGE_SIZE := 26624k
|
|
|
|
|
IMAGES := sysupgrade.bin
|
|
|
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
2023-05-17 20:02:40 +00:00
|
|
|
DEVICE_PACKAGES := kmod-fs-ext4 kmod-mmc kmod-spi-dev
|
2021-01-17 05:54:04 +00:00
|
|
|
endef
|
2022-09-28 15:42:48 +00:00
|
|
|
# Missing DSA Setup
|
|
|
|
|
#TARGET_DEVICES += glinet_gl-s1300
|
2021-01-17 05:54:04 +00:00
|
|
|
|
2022-12-01 04:10:59 +00:00
|
|
|
define Device/kernel-size-6350-8300
|
|
|
|
|
DEVICE_COMPAT_VERSION := 2.0
|
|
|
|
|
DEVICE_COMPAT_MESSAGE := Kernel partition size must be increased for \
|
|
|
|
|
this OpenWrt version. Before continuing, you MUST issue either the \
|
|
|
|
|
command "fw_setenv kernsize 500000" from the OpenWrt command line, \
|
|
|
|
|
or "setenv kernsize 500000 ; saveenv" from the U-Boot serial console. \
|
|
|
|
|
Instead of the sysupgrade image, you must then install the OpenWrt \
|
|
|
|
|
factory image, setting the force flag and wiping the configuration. \
|
|
|
|
|
(e.g. "sysupgrade -n -F openwrt-squashfs-factory.bin" on command line)
|
|
|
|
|
endef
|
|
|
|
|
|
2021-01-17 05:54:04 +00:00
|
|
|
define Device/linksys_ea6350v3
|
|
|
|
|
# The Linksys EA6350v3 has a uboot bootloader that does not
|
|
|
|
|
# support either booting lzma kernel images nor booting UBI
|
|
|
|
|
# partitions. This uboot, however, supports raw kernel images and
|
|
|
|
|
# gzipped images.
|
|
|
|
|
#
|
2022-12-01 04:10:59 +00:00
|
|
|
# As configured by the OEM factory, the device will boot the kernel
|
|
|
|
|
# from a fixed address with a fixed length of 3 MiB. Also, the
|
|
|
|
|
# device has a hard-coded kernel command line that requires the
|
2021-01-17 05:54:04 +00:00
|
|
|
# rootfs and alt_rootfs to be in mtd11 and mtd13 respectively.
|
|
|
|
|
# Oh... and the kernel partition overlaps with the rootfs
|
|
|
|
|
# partition (the same for alt_kernel and alt_rootfs).
|
|
|
|
|
#
|
|
|
|
|
# If you are planing re-partitioning the device, you may want to
|
2022-12-01 04:10:59 +00:00
|
|
|
# keep these details in mind:
|
|
|
|
|
# 1. The kernel addresses you should honor are 0x00000000 and
|
2021-01-17 05:54:04 +00:00
|
|
|
# 0x02800000 respectively.
|
2022-12-01 04:10:59 +00:00
|
|
|
# 2. The kernel size (plus the dtb) cannot exceed 3 MiB in size
|
|
|
|
|
# unless the uboot environment variable "kernsize" is increased.
|
2021-01-17 05:54:04 +00:00
|
|
|
# 3. You can use 'zImage', but not a raw 'Image' packed with lzma.
|
|
|
|
|
# 4. The kernel command line from uboot is harcoded to boot with
|
|
|
|
|
# rootfs either in mtd11 or mtd13.
|
|
|
|
|
$(call Device/FitzImage)
|
2022-12-01 04:10:59 +00:00
|
|
|
$(call Device/kernel-size-6350-8300)
|
2021-01-17 05:54:04 +00:00
|
|
|
DEVICE_VENDOR := Linksys
|
|
|
|
|
DEVICE_MODEL := EA6350
|
|
|
|
|
DEVICE_VARIANT := v3
|
|
|
|
|
SOC := qcom-ipq4018
|
|
|
|
|
BLOCKSIZE := 128k
|
|
|
|
|
PAGESIZE := 2048
|
2022-12-01 04:10:59 +00:00
|
|
|
KERNEL_SIZE := 5120k
|
|
|
|
|
IMAGE_SIZE := 35840k
|
2021-01-17 05:54:04 +00:00
|
|
|
UBINIZE_OPTS := -E 5
|
|
|
|
|
IMAGES += factory.bin
|
|
|
|
|
IMAGE/factory.bin := append-kernel | append-uImage-fakehdr filesystem | pad-to $$$$(KERNEL_SIZE) | append-ubi | linksys-image type=EA6350v3
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += linksys_ea6350v3
|
|
|
|
|
|
|
|
|
|
define Device/linksys_ea8300
|
|
|
|
|
$(call Device/FitzImage)
|
2022-12-01 04:10:59 +00:00
|
|
|
$(call Device/kernel-size-6350-8300)
|
2021-01-17 05:54:04 +00:00
|
|
|
DEVICE_VENDOR := Linksys
|
|
|
|
|
DEVICE_MODEL := EA8300
|
|
|
|
|
SOC := qcom-ipq4019
|
2022-12-01 04:10:59 +00:00
|
|
|
KERNEL_SIZE := 5120k
|
|
|
|
|
IMAGE_SIZE := 84992k
|
2021-01-17 05:54:04 +00:00
|
|
|
BLOCKSIZE := 128k
|
|
|
|
|
PAGESIZE := 2048
|
|
|
|
|
UBINIZE_OPTS := -E 5 # EOD marks to "hide" factory sig at EOF
|
|
|
|
|
IMAGES += factory.bin
|
|
|
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | linksys-image type=EA8300
|
2023-05-17 20:02:40 +00:00
|
|
|
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct kmod-usb-ledtrig-usbport
|
2021-01-17 05:54:04 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += linksys_ea8300
|
|
|
|
|
|
|
|
|
|
define Device/linksys_mr8300
|
|
|
|
|
$(call Device/FitzImage)
|
2022-12-01 04:10:59 +00:00
|
|
|
$(call Device/kernel-size-6350-8300)
|
2021-01-17 05:54:04 +00:00
|
|
|
DEVICE_VENDOR := Linksys
|
|
|
|
|
DEVICE_MODEL := MR8300
|
|
|
|
|
SOC := qcom-ipq4019
|
2022-12-01 04:10:59 +00:00
|
|
|
KERNEL_SIZE := 5120k
|
|
|
|
|
IMAGE_SIZE := 84992k
|
2021-01-17 05:54:04 +00:00
|
|
|
BLOCKSIZE := 128k
|
|
|
|
|
PAGESIZE := 2048
|
|
|
|
|
UBINIZE_OPTS := -E 5 # EOD marks to "hide" factory sig at EOF
|
|
|
|
|
IMAGES += factory.bin
|
|
|
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | linksys-image type=MR8300
|
2022-05-13 20:25:36 +00:00
|
|
|
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct kmod-usb-ledtrig-usbport
|
2021-01-17 05:54:04 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += linksys_mr8300
|
|
|
|
|
|
2022-12-23 17:30:36 +00:00
|
|
|
define Device/linksys_whw03v2
|
|
|
|
|
$(call Device/FitzImage)
|
|
|
|
|
DEVICE_VENDOR := Linksys
|
|
|
|
|
DEVICE_MODEL := WHW03
|
|
|
|
|
DEVICE_VARIANT := V2
|
|
|
|
|
SOC := qcom-ipq4019
|
|
|
|
|
KERNEL_SIZE := 6144k
|
|
|
|
|
IMAGE_SIZE := 158720k
|
|
|
|
|
BLOCKSIZE := 128k
|
|
|
|
|
PAGESIZE := 2048
|
|
|
|
|
UBINIZE_OPTS := -E 5 # EOD marks to "hide" factory sig at EOF
|
|
|
|
|
IMAGES += factory.bin
|
|
|
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | linksys-image type=WHW03v2
|
2023-05-17 20:02:40 +00:00
|
|
|
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct kmod-leds-pca963x kmod-spi-dev kmod-bluetooth
|
2022-12-23 17:30:36 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += linksys_whw03v2
|
|
|
|
|
|
2022-12-06 03:44:32 +00:00
|
|
|
define Device/linksys_whw01
|
2021-06-09 20:35:46 +00:00
|
|
|
$(call Device/FitzImage)
|
|
|
|
|
DEVICE_VENDOR := Linksys
|
|
|
|
|
DEVICE_MODEL := WHW01
|
|
|
|
|
KERNEL_SIZE := 6144k
|
2022-12-06 03:44:32 +00:00
|
|
|
IMAGE_SIZE := 75776K
|
2021-06-09 20:35:46 +00:00
|
|
|
SOC := qcom-ipq4018
|
|
|
|
|
BLOCKSIZE := 128k
|
|
|
|
|
PAGESIZE := 2048
|
|
|
|
|
UBINIZE_OPTS := -E 5 # EOD marks to "hide" factory sig at EOF
|
|
|
|
|
IMAGES += factory.bin
|
2022-12-06 03:44:32 +00:00
|
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | linksys-image type=WHW01
|
2021-06-09 20:35:46 +00:00
|
|
|
DEVICE_PACKAGES := uboot-envtools kmod-leds-pca963x
|
|
|
|
|
endef
|
2022-12-06 03:38:45 +00:00
|
|
|
TARGET_DEVICES += linksys_whw01
|
2021-06-09 20:35:46 +00:00
|
|
|
|
2021-01-17 05:54:04 +00:00
|
|
|
define Device/luma_wrtq-329acn
|
|
|
|
|
$(call Device/FitImage)
|
|
|
|
|
DEVICE_VENDOR := Luma Home
|
|
|
|
|
DEVICE_MODEL := WRTQ-329ACN
|
|
|
|
|
SOC := qcom-ipq4018
|
2022-05-13 20:25:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-ath3k kmod-eeprom-at24 kmod-i2c-gpio
|
2021-01-17 05:54:04 +00:00
|
|
|
IMAGE_SIZE := 76632k
|
|
|
|
|
BLOCKSIZE := 128k
|
|
|
|
|
PAGESIZE := 2048
|
|
|
|
|
endef
|
2022-10-03 12:58:53 +00:00
|
|
|
TARGET_DEVICES += luma_wrtq-329acn
|
2021-01-17 05:54:04 +00:00
|
|
|
|
|
|
|
|
define Device/meraki_mr33
|
|
|
|
|
$(call Device/FitImage)
|
|
|
|
|
DEVICE_VENDOR := Cisco Meraki
|
|
|
|
|
DEVICE_MODEL := MR33
|
|
|
|
|
SOC := qcom-ipq4029
|
|
|
|
|
BLOCKSIZE := 128k
|
|
|
|
|
PAGESIZE := 2048
|
|
|
|
|
DEVICE_PACKAGES := -swconfig ath10k-firmware-qca9887-ct
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += meraki_mr33
|
|
|
|
|
|
2022-06-14 09:08:22 +00:00
|
|
|
define Device/meraki_mr74
|
|
|
|
|
$(call Device/FitImage)
|
|
|
|
|
DEVICE_VENDOR := Cisco Meraki
|
|
|
|
|
DEVICE_MODEL := MR74
|
|
|
|
|
SOC := qcom-ipq4029
|
|
|
|
|
BLOCKSIZE := 128k
|
|
|
|
|
PAGESIZE := 2048
|
|
|
|
|
DEVICE_PACKAGES := -swconfig ath10k-firmware-qca9887-ct
|
|
|
|
|
DEVICE_DTS_CONFIG := config@3
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += meraki_mr74
|
|
|
|
|
|
2021-01-17 05:54:04 +00:00
|
|
|
define Device/mobipromo_cm520-79f
|
|
|
|
|
$(call Device/FitzImage)
|
|
|
|
|
$(call Device/UbiFit)
|
|
|
|
|
DEVICE_VENDOR := MobiPromo
|
|
|
|
|
DEVICE_MODEL := CM520-79F
|
|
|
|
|
SOC := qcom-ipq4019
|
|
|
|
|
BLOCKSIZE := 128k
|
|
|
|
|
PAGESIZE := 2048
|
2022-05-13 20:25:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-usb-ledtrig-usbport
|
2021-01-17 05:54:04 +00:00
|
|
|
endef
|
2022-10-14 07:58:46 +00:00
|
|
|
TARGET_DEVICES += mobipromo_cm520-79f
|
2021-01-17 05:54:04 +00:00
|
|
|
|
|
|
|
|
define Device/netgear_ex61x0v2
|
|
|
|
|
$(call Device/DniImage)
|
|
|
|
|
DEVICE_VENDOR := NETGEAR
|
|
|
|
|
DEVICE_DTS_CONFIG := config@4
|
|
|
|
|
NETGEAR_BOARD_ID := EX6150v2series
|
|
|
|
|
NETGEAR_HW_ID := 29765285+16+0+128+2x2
|
|
|
|
|
IMAGE_SIZE := 14400k
|
|
|
|
|
SOC := qcom-ipq4018
|
|
|
|
|
endef
|
|
|
|
|
|
|
|
|
|
define Device/netgear_ex6100v2
|
|
|
|
|
$(call Device/netgear_ex61x0v2)
|
|
|
|
|
DEVICE_MODEL := EX6100
|
|
|
|
|
DEVICE_VARIANT := v2
|
|
|
|
|
endef
|
2023-03-06 20:27:49 +00:00
|
|
|
TARGET_DEVICES += netgear_ex6100v2
|
2021-01-17 05:54:04 +00:00
|
|
|
|
|
|
|
|
define Device/netgear_ex6150v2
|
|
|
|
|
$(call Device/netgear_ex61x0v2)
|
|
|
|
|
DEVICE_MODEL := EX6150
|
|
|
|
|
DEVICE_VARIANT := v2
|
|
|
|
|
endef
|
2023-03-06 20:27:49 +00:00
|
|
|
TARGET_DEVICES += netgear_ex6150v2
|
2021-01-17 05:54:04 +00:00
|
|
|
|
2020-09-02 00:10:16 +00:00
|
|
|
define Device/netgear_orbi
|
|
|
|
|
$(call Device/DniImage)
|
|
|
|
|
SOC := qcom-ipq4019
|
|
|
|
|
DEVICE_VENDOR := NETGEAR
|
|
|
|
|
IMAGE/factory.img := append-kernel | pad-offset 128k 64 | \
|
|
|
|
|
append-uImage-fakehdr filesystem | pad-to $$$$(KERNEL_SIZE) | \
|
|
|
|
|
append-rootfs | pad-rootfs | netgear-dni
|
|
|
|
|
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-to 64k | \
|
|
|
|
|
sysupgrade-tar rootfs=$$$$@ | append-metadata
|
|
|
|
|
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct e2fsprogs kmod-fs-ext4 losetup
|
|
|
|
|
endef
|
|
|
|
|
|
|
|
|
|
define Device/netgear_rbx50
|
|
|
|
|
$(call Device/netgear_orbi)
|
|
|
|
|
NETGEAR_HW_ID := 29765352+0+4000+512+2x2+2x2+4x4
|
|
|
|
|
KERNEL_SIZE := 3932160
|
|
|
|
|
ROOTFS_SIZE := 32243712
|
|
|
|
|
IMAGE_SIZE := 36175872
|
|
|
|
|
endef
|
|
|
|
|
|
|
|
|
|
define Device/netgear_rbr50
|
|
|
|
|
$(call Device/netgear_rbx50)
|
|
|
|
|
DEVICE_MODEL := RBR50
|
|
|
|
|
DEVICE_VARIANT := v1
|
|
|
|
|
NETGEAR_BOARD_ID := RBR50
|
|
|
|
|
endef
|
2022-10-04 21:20:39 +00:00
|
|
|
TARGET_DEVICES += netgear_rbr50
|
2020-09-02 00:10:16 +00:00
|
|
|
|
|
|
|
|
define Device/netgear_rbs50
|
|
|
|
|
$(call Device/netgear_rbx50)
|
|
|
|
|
DEVICE_MODEL := RBS50
|
|
|
|
|
DEVICE_VARIANT := v1
|
|
|
|
|
NETGEAR_BOARD_ID := RBS50
|
|
|
|
|
endef
|
2022-10-04 21:20:39 +00:00
|
|
|
TARGET_DEVICES += netgear_rbs50
|
2020-09-02 00:10:16 +00:00
|
|
|
|
|
|
|
|
define Device/netgear_srx60
|
|
|
|
|
$(call Device/netgear_orbi)
|
|
|
|
|
NETGEAR_HW_ID := 29765352+0+4096+512+2x2+2x2+4x4
|
|
|
|
|
KERNEL_SIZE := 3932160
|
|
|
|
|
ROOTFS_SIZE := 32243712
|
|
|
|
|
IMAGE_SIZE := 36175872
|
|
|
|
|
endef
|
|
|
|
|
|
|
|
|
|
define Device/netgear_srr60
|
|
|
|
|
$(call Device/netgear_srx60)
|
|
|
|
|
DEVICE_MODEL := SRR60
|
|
|
|
|
NETGEAR_BOARD_ID := SRR60
|
|
|
|
|
endef
|
2022-10-04 21:20:39 +00:00
|
|
|
TARGET_DEVICES += netgear_srr60
|
2020-09-02 00:10:16 +00:00
|
|
|
|
|
|
|
|
define Device/netgear_srs60
|
|
|
|
|
$(call Device/netgear_srx60)
|
|
|
|
|
DEVICE_MODEL := SRS60
|
|
|
|
|
NETGEAR_BOARD_ID := SRS60
|
|
|
|
|
endef
|
2022-10-04 21:20:39 +00:00
|
|
|
TARGET_DEVICES += netgear_srs60
|
2020-09-02 00:10:16 +00:00
|
|
|
|
ipq40xx: add netgear wac510 support
This adds support for the Netgear WAC510 Insight Managed Smart Cloud
Wireless Access Point, an indoor dual-band, dual-radio 802.11ac
business-class wireless AP with integrated omnidirectional antennae
and two 10/100/1000 Mbps Ethernet ports.
For more information see:
<https://www.netgear.com/business/wifi/access-points/wac510>
Specifications:
SoC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 256 MiB
Flash1: 2 MiB Winbond W25Q16JV SPI-NOR
Flash2: 128 MiB Winbond W25N01GVZEIG SPI-NAND
Ethernet: Built-in IPQ4018 (SoC, QCA8072 PHY), 2x 1000/100/10 port,
WAN port active IEEE 802.3af/at PoE in
Wireless1: Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 3 dBi antennae
Wireless2: Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 4 dBi antennae
Input: (Optional) Barrel 12 V 2.5 A Power, Reset button SW1
LEDs: Power, Insight, WAN PoE, LAN, 2.4G WLAN, 5G WLAN
Serial: Header J2
1 - 3.3 Volt (Do NOT connect!)
2 - TX
3 - RX
4 - Ground
WARNING: The serial port needs a TTL/RS-232 3.3 volt level converter!
The Serial settings are 115200-8-N-1.
Installation via Stock Web Interface:
BTW: The default factory console/web interface login user/password are
admin/password.
In the web interface navigating to Management - Maintenance - Upgrade -
'Firmware Upgrade' will show you what is currently installed e.g.:
Manage Firmware
Current Firmware Version: V5.0.10.2
Backup Firmware Version: V1.2.5.11
Under 'Upgrade Options' choose Local (alternatively SFTP would be
available) then click/select 'Browse File' on the right side, choose
openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.tar
and hit the Upgrade button below. After a minute or two your browser
should indicate completion printing 'Firmware update complete.' and
'Rebooting AP...'.
Note that OpenWrt will use the WAN PoE port as actual WAN port
defaulting to DHCP client but NOT allowing LuCI access, use LAN port
defaulting to 192.168.1.1/24 to access LuCI.
Installation via TFTP Requiring Serial U-Boot Access:
Connect to the device's serial port and hit any key to stop autoboot.
Upload and boot the initramfs based OpenWrt image as follows:
(IPQ40xx) # setenv serverip 192.168.1.1
(IPQ40xx) # setenv ipaddr 192.168.1.2
(IPQ40xx) # tftpboot openwrt-ipq40xx-generic-netgear_wac510-initramfs-fit-uImage.itb
(IPQ40xx) # bootm
Note: This only runs OpenWrt from RAM and has not installed anything
to flash as of yet. One may permanently install OpenWrt as follows:
Check the MTD device number of the active partition:
root@OpenWrt:/# dmesg | grep 'set to be root filesystem'
[ 1.010084] mtd: device 9 (rootfs) set to be root filesystem
Upload the factory image ending with .ubi to /tmp (e.g. using scp or
tftp). Then flash the image as follows (substituting the 9 in mtd9
below with whatever number reported above):
root@OpenWrt:/# ubiformat /dev/mtd9 -f /tmp/openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.ubi
And reboot.
Dual Image Configuration:
The default U-Boot boot command bootipq uses the U-Boot environment
variables primary/secondary to decide which image to boot. E.g.
primary=0, secondary=3800000 uses rootfs while primary=3800000,
secondary=0 uses rootfs_1.
Switching their values changes the active partition. E.g. from within
U-Boot:
(IPQ40xx) # setenv primary 0
(IPQ40xx) # setenv secondary 3800000
(IPQ40xx) # saveenv
Or from a OpenWrt userspace serial/SSH console:
fw_setenv primary 0
fw_setenv secondary 3800000
Note that if you install two copies of OpenWrt then each will have its
independent configuration not like when switching partitions on the
stock firmware.
BTW: The kernel log shows which boot partition is active:
[ 2.439050] ubi0: attached mtd9 (name "rootfs", size 56 MiB)
vs.
[ 2.978785] ubi0: attached mtd10 (name "rootfs_1", size 56 MiB)
Note: After 3 failed boot attempts it automatically switches partition.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
[squashed netgear-tar commit into main and rename netgear-tar for
now, until it is made generic.]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-11-25 13:23:58 +00:00
|
|
|
define Device/netgear_wac510
|
|
|
|
|
$(call Device/FitImage)
|
|
|
|
|
$(call Device/UbiFit)
|
|
|
|
|
DEVICE_VENDOR := Netgear
|
|
|
|
|
DEVICE_MODEL := WAC510
|
|
|
|
|
SOC := qcom-ipq4018
|
|
|
|
|
DEVICE_DTS_CONFIG := config@5
|
|
|
|
|
BLOCKSIZE := 128k
|
|
|
|
|
PAGESIZE := 2048
|
2022-11-17 01:52:50 +00:00
|
|
|
IMAGES += factory.tar
|
|
|
|
|
IMAGE/factory.tar := append-ubi | wac5xx-netgear-tar
|
ipq40xx: add netgear wac510 support
This adds support for the Netgear WAC510 Insight Managed Smart Cloud
Wireless Access Point, an indoor dual-band, dual-radio 802.11ac
business-class wireless AP with integrated omnidirectional antennae
and two 10/100/1000 Mbps Ethernet ports.
For more information see:
<https://www.netgear.com/business/wifi/access-points/wac510>
Specifications:
SoC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 256 MiB
Flash1: 2 MiB Winbond W25Q16JV SPI-NOR
Flash2: 128 MiB Winbond W25N01GVZEIG SPI-NAND
Ethernet: Built-in IPQ4018 (SoC, QCA8072 PHY), 2x 1000/100/10 port,
WAN port active IEEE 802.3af/at PoE in
Wireless1: Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 3 dBi antennae
Wireless2: Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 4 dBi antennae
Input: (Optional) Barrel 12 V 2.5 A Power, Reset button SW1
LEDs: Power, Insight, WAN PoE, LAN, 2.4G WLAN, 5G WLAN
Serial: Header J2
1 - 3.3 Volt (Do NOT connect!)
2 - TX
3 - RX
4 - Ground
WARNING: The serial port needs a TTL/RS-232 3.3 volt level converter!
The Serial settings are 115200-8-N-1.
Installation via Stock Web Interface:
BTW: The default factory console/web interface login user/password are
admin/password.
In the web interface navigating to Management - Maintenance - Upgrade -
'Firmware Upgrade' will show you what is currently installed e.g.:
Manage Firmware
Current Firmware Version: V5.0.10.2
Backup Firmware Version: V1.2.5.11
Under 'Upgrade Options' choose Local (alternatively SFTP would be
available) then click/select 'Browse File' on the right side, choose
openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.tar
and hit the Upgrade button below. After a minute or two your browser
should indicate completion printing 'Firmware update complete.' and
'Rebooting AP...'.
Note that OpenWrt will use the WAN PoE port as actual WAN port
defaulting to DHCP client but NOT allowing LuCI access, use LAN port
defaulting to 192.168.1.1/24 to access LuCI.
Installation via TFTP Requiring Serial U-Boot Access:
Connect to the device's serial port and hit any key to stop autoboot.
Upload and boot the initramfs based OpenWrt image as follows:
(IPQ40xx) # setenv serverip 192.168.1.1
(IPQ40xx) # setenv ipaddr 192.168.1.2
(IPQ40xx) # tftpboot openwrt-ipq40xx-generic-netgear_wac510-initramfs-fit-uImage.itb
(IPQ40xx) # bootm
Note: This only runs OpenWrt from RAM and has not installed anything
to flash as of yet. One may permanently install OpenWrt as follows:
Check the MTD device number of the active partition:
root@OpenWrt:/# dmesg | grep 'set to be root filesystem'
[ 1.010084] mtd: device 9 (rootfs) set to be root filesystem
Upload the factory image ending with .ubi to /tmp (e.g. using scp or
tftp). Then flash the image as follows (substituting the 9 in mtd9
below with whatever number reported above):
root@OpenWrt:/# ubiformat /dev/mtd9 -f /tmp/openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.ubi
And reboot.
Dual Image Configuration:
The default U-Boot boot command bootipq uses the U-Boot environment
variables primary/secondary to decide which image to boot. E.g.
primary=0, secondary=3800000 uses rootfs while primary=3800000,
secondary=0 uses rootfs_1.
Switching their values changes the active partition. E.g. from within
U-Boot:
(IPQ40xx) # setenv primary 0
(IPQ40xx) # setenv secondary 3800000
(IPQ40xx) # saveenv
Or from a OpenWrt userspace serial/SSH console:
fw_setenv primary 0
fw_setenv secondary 3800000
Note that if you install two copies of OpenWrt then each will have its
independent configuration not like when switching partitions on the
stock firmware.
BTW: The kernel log shows which boot partition is active:
[ 2.439050] ubi0: attached mtd9 (name "rootfs", size 56 MiB)
vs.
[ 2.978785] ubi0: attached mtd10 (name "rootfs_1", size 56 MiB)
Note: After 3 failed boot attempts it automatically switches partition.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
[squashed netgear-tar commit into main and rename netgear-tar for
now, until it is made generic.]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-11-25 13:23:58 +00:00
|
|
|
DEVICE_PACKAGES := uboot-envtools
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += netgear_wac510
|
|
|
|
|
|
2021-01-17 05:54:04 +00:00
|
|
|
define Device/openmesh_a42
|
|
|
|
|
$(call Device/FitImageLzma)
|
|
|
|
|
DEVICE_VENDOR := OpenMesh
|
|
|
|
|
DEVICE_MODEL := A42
|
|
|
|
|
SOC := qcom-ipq4018
|
|
|
|
|
DEVICE_DTS_CONFIG := config@om.a42
|
|
|
|
|
BLOCKSIZE := 64k
|
2022-08-25 18:26:11 +00:00
|
|
|
KERNEL = kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
|
2021-01-17 05:54:04 +00:00
|
|
|
IMAGE_SIZE := 15616k
|
|
|
|
|
IMAGES += factory.bin
|
|
|
|
|
IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=A42
|
|
|
|
|
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
|
|
|
|
|
endef
|
2022-10-24 16:55:44 +00:00
|
|
|
TARGET_DEVICES += openmesh_a42
|
2021-01-17 05:54:04 +00:00
|
|
|
|
|
|
|
|
define Device/openmesh_a62
|
|
|
|
|
$(call Device/FitImageLzma)
|
|
|
|
|
DEVICE_VENDOR := OpenMesh
|
|
|
|
|
DEVICE_MODEL := A62
|
|
|
|
|
SOC := qcom-ipq4019
|
|
|
|
|
DEVICE_DTS_CONFIG := config@om.a62
|
|
|
|
|
BLOCKSIZE := 64k
|
2022-08-25 18:26:11 +00:00
|
|
|
KERNEL = kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
|
2021-01-17 05:54:04 +00:00
|
|
|
IMAGE_SIZE := 15552k
|
|
|
|
|
IMAGES += factory.bin
|
|
|
|
|
IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=A62
|
|
|
|
|
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
|
2021-05-25 13:26:06 +00:00
|
|
|
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct
|
2021-01-17 05:54:04 +00:00
|
|
|
endef
|
2022-10-24 16:55:44 +00:00
|
|
|
TARGET_DEVICES += openmesh_a62
|
2021-01-17 05:54:04 +00:00
|
|
|
|
ipq40xx: add support for P&W R619AC (aka G-DOCK 2.0)
P&W R619AC is a IPQ4019 Dual-Band AC1200 router.
It is made by P&W (p2w-tech.com) known as P&W R619AC
but marketed and sold more popularly as G-DOCK 2.0.
Specification:
* SOC: Qualcomm Atheros IPQ4019 (717 MHz)
* RAM: 512 MiB
* Flash: 16 MiB (NOR) + 128 MiB (NAND)
* Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN)
* Wireless:
- 2.4 GHz b/g/n Qualcomm Atheros IPQ4019
- 5 GHz a/n/ac Qualcomm Atheros IPQ4019
* USB: 1 x USB 3.0
* LED: 4 x LAN, 1 x WAN, 2 x WiFi, 1 x Power (All Blue LED)
* Input: 1 x reset
* 1 x MicroSD card slot
* Serial console: 115200bps, pinheader J2 on PCB
* Power: DC 12V 2A
* 1 x Unpopulated mPCIe Slot (see below how to connect it)
* 1 x Unpopulated Sim Card Slot
Installation:
1. Access to tty console via UART serial
2. Enter failsafe mode and mount rootfs
<https://openwrt.org/docs/guide-user/troubleshooting/failsafe_and_factory_reset>
3. Edit inittab to enable shell on tty console
`sed -i 's/#ttyM/ttyM/' /etc/inittab`
4. Reboot and upload `-nand-factory.bin` to the router (using wget)
5. Use `sysupgrade` command to install
Another installation method is to hijack the upgrade server domain
of stock firmware, because it's using insecure http.
This commit is based on @LGA1150(at GitHub)'s work
<https://github.com/LGA1150/openwrt/commit/a4932c8d5a275d1fb4297bd20ec03f9270a45d1c>
With some changes:
1. Added `qpic_bam` node in dts. I don't know much about this,
but I observed other dtses have this node.
2. Removed `ldo` node under `sd_0_pinmux`, because `ldo` cause SD card not
working. This fix is from
<https://github.com/coolsnowwolf/lede/commit/51143b4c7571f717afe071db60bbb4db1532cbf2>
3. Removed the 32MB NOR variant.
4. Removed `cd-gpios` in `sdhci` node, because it's reported that it makes
wlan2g led light up.
5. Added ethphy led config in dts.
6. Changed nand partition label from `rootfs` to `ubi`.
About the 128MiB variant: The stock bootloader sets size of nand to 64MiB.
But most of this devices have 128MiB nand. If you want to use all 128MiB,
you need to modify the `MIBIB` data of bootloader. More details can be
found on github:
<https://github.com/openwrt/openwrt/pull/3691#issuecomment-818770060>
For instructions on how to flash the MIBIB partition from u-boot console:
<https://github.com/openwrt/openwrt/pull/3691#issuecomment-819138232>
About the Mini PCIe slot: (from "ygleg")
"The REFCLK signals on the Mini PCIe slot is not connected on
this board out of the box. If you want to use the Mini PCIe slot
on the board, you need to (preferably) solder two 0402 resistors:
R436 (REFCLK+) and R444 (REFCLK-)..."
This and much more information is provoided in the github comment:
<https://github.com/openwrt/openwrt/pull/3691#issuecomment-968054670>
Signed-off-by: Richard Yu <yurichard3839@gmail.com>
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
[Added comment about MIBIB+128 MiB variant. Added commit
message section about pcie slot. Renamed gpio-leds' subnodes
and added color, function+enum properties.]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-11-12 03:16:21 +00:00
|
|
|
define Device/p2w_r619ac
|
|
|
|
|
$(call Device/FitzImage)
|
|
|
|
|
$(call Device/UbiFit)
|
|
|
|
|
DEVICE_VENDOR := P&W
|
|
|
|
|
DEVICE_MODEL := R619AC
|
|
|
|
|
SOC := qcom-ipq4019
|
|
|
|
|
DEVICE_DTS_CONFIG := config@10
|
|
|
|
|
BLOCKSIZE := 128k
|
|
|
|
|
PAGESIZE := 2048
|
|
|
|
|
endef
|
|
|
|
|
|
|
|
|
|
define Device/p2w_r619ac-64m
|
|
|
|
|
$(call Device/p2w_r619ac)
|
|
|
|
|
DEVICE_VARIANT := 64M NAND
|
2022-11-17 01:52:50 +00:00
|
|
|
IMAGES += factory.bin
|
|
|
|
|
IMAGE/factory.bin := append-ubi | qsdk-ipq-factory-nand
|
ipq40xx: add support for P&W R619AC (aka G-DOCK 2.0)
P&W R619AC is a IPQ4019 Dual-Band AC1200 router.
It is made by P&W (p2w-tech.com) known as P&W R619AC
but marketed and sold more popularly as G-DOCK 2.0.
Specification:
* SOC: Qualcomm Atheros IPQ4019 (717 MHz)
* RAM: 512 MiB
* Flash: 16 MiB (NOR) + 128 MiB (NAND)
* Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN)
* Wireless:
- 2.4 GHz b/g/n Qualcomm Atheros IPQ4019
- 5 GHz a/n/ac Qualcomm Atheros IPQ4019
* USB: 1 x USB 3.0
* LED: 4 x LAN, 1 x WAN, 2 x WiFi, 1 x Power (All Blue LED)
* Input: 1 x reset
* 1 x MicroSD card slot
* Serial console: 115200bps, pinheader J2 on PCB
* Power: DC 12V 2A
* 1 x Unpopulated mPCIe Slot (see below how to connect it)
* 1 x Unpopulated Sim Card Slot
Installation:
1. Access to tty console via UART serial
2. Enter failsafe mode and mount rootfs
<https://openwrt.org/docs/guide-user/troubleshooting/failsafe_and_factory_reset>
3. Edit inittab to enable shell on tty console
`sed -i 's/#ttyM/ttyM/' /etc/inittab`
4. Reboot and upload `-nand-factory.bin` to the router (using wget)
5. Use `sysupgrade` command to install
Another installation method is to hijack the upgrade server domain
of stock firmware, because it's using insecure http.
This commit is based on @LGA1150(at GitHub)'s work
<https://github.com/LGA1150/openwrt/commit/a4932c8d5a275d1fb4297bd20ec03f9270a45d1c>
With some changes:
1. Added `qpic_bam` node in dts. I don't know much about this,
but I observed other dtses have this node.
2. Removed `ldo` node under `sd_0_pinmux`, because `ldo` cause SD card not
working. This fix is from
<https://github.com/coolsnowwolf/lede/commit/51143b4c7571f717afe071db60bbb4db1532cbf2>
3. Removed the 32MB NOR variant.
4. Removed `cd-gpios` in `sdhci` node, because it's reported that it makes
wlan2g led light up.
5. Added ethphy led config in dts.
6. Changed nand partition label from `rootfs` to `ubi`.
About the 128MiB variant: The stock bootloader sets size of nand to 64MiB.
But most of this devices have 128MiB nand. If you want to use all 128MiB,
you need to modify the `MIBIB` data of bootloader. More details can be
found on github:
<https://github.com/openwrt/openwrt/pull/3691#issuecomment-818770060>
For instructions on how to flash the MIBIB partition from u-boot console:
<https://github.com/openwrt/openwrt/pull/3691#issuecomment-819138232>
About the Mini PCIe slot: (from "ygleg")
"The REFCLK signals on the Mini PCIe slot is not connected on
this board out of the box. If you want to use the Mini PCIe slot
on the board, you need to (preferably) solder two 0402 resistors:
R436 (REFCLK+) and R444 (REFCLK-)..."
This and much more information is provoided in the github comment:
<https://github.com/openwrt/openwrt/pull/3691#issuecomment-968054670>
Signed-off-by: Richard Yu <yurichard3839@gmail.com>
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
[Added comment about MIBIB+128 MiB variant. Added commit
message section about pcie slot. Renamed gpio-leds' subnodes
and added color, function+enum properties.]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-11-12 03:16:21 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += p2w_r619ac-64m
|
|
|
|
|
|
|
|
|
|
define Device/p2w_r619ac-128m
|
|
|
|
|
$(call Device/p2w_r619ac)
|
|
|
|
|
DEVICE_VARIANT := 128M NAND
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += p2w_r619ac-128m
|
|
|
|
|
|
ipq40xx: add support for Pakedge WR-1
Pakedge WR-1 is a dual-band wireless router.
Specification
SoC: Qualcomm Atheros IPQ4018
RAM: 256 MB DDR3
Flash: 32 MB SPI NOR
WIFI: 2.4 GHz 2T2R integrated
5 GHz 2T2R integrated
Ethernet: 5x 10/100/1000 Mbps QCA8075
USB: 1x 2.0
LEDS: 8x (3 GPIO controlled, 5 connected to switch)
Buttons: 1x GPIO controlled
UART: pin header J5
1. 3.3V, 2. GND, 3. TX, 4. RX
baud: 115200, parity: none, flow control: none
Installation
1. Rename initramfs image to:
openwrt-ipq806x-qcom-ipq40xx-ap.dk01.1-c1-fit-uImage-initramfs.itb
and copy it to USB flash drive with FAT32 file system.
2. Connect USB flash drive to the router and apply power while pressing
reset button. Hold the button, on the lates bootloader version, when
Power and WiFi-5 LEDs will start blinking release it. For the older
bootloader holding it for 15 seconds should suffice.
3. Now the router boots the initramfs image, at some point (close to one
minute) the Power LED will start blinking, when stops, router is fully
booted.
4. Connect to one of LAN ports and use SSH to open the shell at
192.168.1.1.
5. ATTENTION! now backup the mtd8 and mtd9 partitions, it's necessary if,
at some point, You want to go back to original firmware. The firmware
provided by manufacturer on its site is encrypted and U-Boot accepts
only decrypted factory images, so there's no way to restore original
firmware.
6. If the backup is prepared, transfer the sysupgrade image to the router
and use 'sysupgrade' command to flash it.
7. After successful flashing router will reboot. At some point the Power
LED will start blinking, wait till it stops, then router is ready for
configuration.
Additional information
U-Boot command line is password protected. Password is unknown.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
2022-09-06 13:32:33 +00:00
|
|
|
define Device/pakedge_wr-1
|
|
|
|
|
$(call Device/FitImageLzma)
|
|
|
|
|
DEVICE_VENDOR := Pakedge
|
|
|
|
|
DEVICE_MODEL := WR-1
|
|
|
|
|
DEVICE_DTS_CONFIG := config@ap.dk01.1-c1
|
|
|
|
|
SOC := qcom-ipq4018
|
|
|
|
|
BLOCKSIZE := 64k
|
|
|
|
|
IMAGE_SIZE := 31232k
|
|
|
|
|
IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | append-metadata
|
|
|
|
|
endef
|
2022-10-03 12:59:15 +00:00
|
|
|
TARGET_DEVICES += pakedge_wr-1
|
ipq40xx: add support for Pakedge WR-1
Pakedge WR-1 is a dual-band wireless router.
Specification
SoC: Qualcomm Atheros IPQ4018
RAM: 256 MB DDR3
Flash: 32 MB SPI NOR
WIFI: 2.4 GHz 2T2R integrated
5 GHz 2T2R integrated
Ethernet: 5x 10/100/1000 Mbps QCA8075
USB: 1x 2.0
LEDS: 8x (3 GPIO controlled, 5 connected to switch)
Buttons: 1x GPIO controlled
UART: pin header J5
1. 3.3V, 2. GND, 3. TX, 4. RX
baud: 115200, parity: none, flow control: none
Installation
1. Rename initramfs image to:
openwrt-ipq806x-qcom-ipq40xx-ap.dk01.1-c1-fit-uImage-initramfs.itb
and copy it to USB flash drive with FAT32 file system.
2. Connect USB flash drive to the router and apply power while pressing
reset button. Hold the button, on the lates bootloader version, when
Power and WiFi-5 LEDs will start blinking release it. For the older
bootloader holding it for 15 seconds should suffice.
3. Now the router boots the initramfs image, at some point (close to one
minute) the Power LED will start blinking, when stops, router is fully
booted.
4. Connect to one of LAN ports and use SSH to open the shell at
192.168.1.1.
5. ATTENTION! now backup the mtd8 and mtd9 partitions, it's necessary if,
at some point, You want to go back to original firmware. The firmware
provided by manufacturer on its site is encrypted and U-Boot accepts
only decrypted factory images, so there's no way to restore original
firmware.
6. If the backup is prepared, transfer the sysupgrade image to the router
and use 'sysupgrade' command to flash it.
7. After successful flashing router will reboot. At some point the Power
LED will start blinking, wait till it stops, then router is ready for
configuration.
Additional information
U-Boot command line is password protected. Password is unknown.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
2022-09-06 13:32:33 +00:00
|
|
|
|
2021-01-17 05:54:04 +00:00
|
|
|
define Device/plasmacloud_pa1200
|
|
|
|
|
$(call Device/FitImageLzma)
|
|
|
|
|
DEVICE_VENDOR := Plasma Cloud
|
|
|
|
|
DEVICE_MODEL := PA1200
|
|
|
|
|
SOC := qcom-ipq4018
|
|
|
|
|
DEVICE_DTS_CONFIG := config@pc.pa1200
|
|
|
|
|
BLOCKSIZE := 64k
|
2022-08-25 18:26:11 +00:00
|
|
|
KERNEL = kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
|
2021-01-17 05:54:04 +00:00
|
|
|
IMAGE_SIZE := 15616k
|
|
|
|
|
IMAGES += factory.bin
|
|
|
|
|
IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=PA1200
|
|
|
|
|
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
|
|
|
|
|
endef
|
2022-10-24 16:55:44 +00:00
|
|
|
TARGET_DEVICES += plasmacloud_pa1200
|
2021-01-17 05:54:04 +00:00
|
|
|
|
|
|
|
|
define Device/plasmacloud_pa2200
|
|
|
|
|
$(call Device/FitImageLzma)
|
|
|
|
|
DEVICE_VENDOR := Plasma Cloud
|
|
|
|
|
DEVICE_MODEL := PA2200
|
|
|
|
|
SOC := qcom-ipq4019
|
|
|
|
|
DEVICE_DTS_CONFIG := config@pc.pa2200
|
|
|
|
|
BLOCKSIZE := 64k
|
2022-08-25 18:26:11 +00:00
|
|
|
KERNEL = kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
|
2021-01-17 05:54:04 +00:00
|
|
|
IMAGE_SIZE := 15552k
|
|
|
|
|
IMAGES += factory.bin
|
|
|
|
|
IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=PA2200
|
|
|
|
|
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
|
2022-05-13 20:25:36 +00:00
|
|
|
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct
|
2021-01-17 05:54:04 +00:00
|
|
|
endef
|
2022-10-24 16:55:44 +00:00
|
|
|
TARGET_DEVICES += plasmacloud_pa2200
|
2021-01-17 05:54:04 +00:00
|
|
|
|
|
|
|
|
define Device/qcom_ap-dk01.1-c1
|
|
|
|
|
DEVICE_VENDOR := Qualcomm Atheros
|
|
|
|
|
DEVICE_MODEL := AP-DK01.1
|
|
|
|
|
DEVICE_VARIANT := C1
|
|
|
|
|
BOARD_NAME := ap-dk01.1-c1
|
|
|
|
|
SOC := qcom-ipq4019
|
|
|
|
|
DEVICE_DTS := qcom-ipq4019-ap.dk01.1-c1
|
|
|
|
|
KERNEL_INSTALL := 1
|
|
|
|
|
KERNEL_SIZE := 4096k
|
|
|
|
|
IMAGE_SIZE := 26624k
|
|
|
|
|
$(call Device/FitImage)
|
|
|
|
|
IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-rootfs | pad-rootfs | append-metadata
|
2021-11-03 15:45:38 +00:00
|
|
|
DEFAULT := n
|
2021-01-17 05:54:04 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += qcom_ap-dk01.1-c1
|
|
|
|
|
|
|
|
|
|
define Device/qcom_ap-dk04.1-c1
|
|
|
|
|
$(call Device/FitImage)
|
|
|
|
|
$(call Device/UbiFit)
|
|
|
|
|
DEVICE_VENDOR := Qualcomm Atheros
|
|
|
|
|
DEVICE_MODEL := AP-DK04.1
|
|
|
|
|
DEVICE_VARIANT := C1
|
|
|
|
|
SOC := qcom-ipq4019
|
|
|
|
|
DEVICE_DTS := qcom-ipq4019-ap.dk04.1-c1
|
|
|
|
|
KERNEL_INSTALL := 1
|
|
|
|
|
KERNEL_SIZE := 4048k
|
|
|
|
|
BLOCKSIZE := 128k
|
|
|
|
|
PAGESIZE := 2048
|
|
|
|
|
BOARD_NAME := ap-dk04.1-c1
|
2021-11-03 15:45:38 +00:00
|
|
|
DEFAULT := n
|
2021-01-17 05:54:04 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += qcom_ap-dk04.1-c1
|
|
|
|
|
|
|
|
|
|
define Device/qxwlan_e2600ac-c1
|
|
|
|
|
$(call Device/FitImage)
|
|
|
|
|
DEVICE_VENDOR := Qxwlan
|
|
|
|
|
DEVICE_MODEL := E2600AC
|
|
|
|
|
DEVICE_VARIANT := C1
|
|
|
|
|
BOARD_NAME := e2600ac-c1
|
|
|
|
|
SOC := qcom-ipq4019
|
|
|
|
|
IMAGE_SIZE := 31232k
|
|
|
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
|
|
|
|
endef
|
2023-02-22 12:46:28 +00:00
|
|
|
TARGET_DEVICES += qxwlan_e2600ac-c1
|
2021-01-17 05:54:04 +00:00
|
|
|
|
|
|
|
|
define Device/qxwlan_e2600ac-c2
|
|
|
|
|
$(call Device/FitImage)
|
|
|
|
|
$(call Device/UbiFit)
|
|
|
|
|
DEVICE_VENDOR := Qxwlan
|
|
|
|
|
DEVICE_MODEL := E2600AC
|
|
|
|
|
DEVICE_VARIANT := C2
|
|
|
|
|
SOC := qcom-ipq4019
|
|
|
|
|
KERNEL_INSTALL := 1
|
|
|
|
|
BLOCKSIZE := 128k
|
|
|
|
|
PAGESIZE := 2048
|
|
|
|
|
endef
|
2023-02-22 12:55:44 +00:00
|
|
|
TARGET_DEVICES += qxwlan_e2600ac-c2
|
2021-01-17 05:54:04 +00:00
|
|
|
|
ipq40xx: add support for Sony NCP-HG100/Cellular
Sony NCP-HG100/Cellular is a IoT Gateway with 2.4/5 GHz band 11ac
(WiFi-5) wireless function, based on IPQ4019.
Specification:
- SoC : Qualcomm IPQ4019
- RAM : DDR3 512 MiB (H5TC4G63EFR)
- Flash : eMMC 4 GiB (THGBMNG5D1LBAIT)
- WLAN : 2.4/5 GHz 2T2R (IPQ4019)
- Ethernet : 10/100/1000 Mbps x2
- Transceiver : Qualcomm QCA8072
- WWAN : Telit LN940A9
- Z-Wave : Silicon Labs ZM5101
- Bluetooth : Qualcomm CSR8811
- Audio DAC : Realtek ALC5629
- Audio Amp. : Realtek ALC1304
- Voice Input Processor : Conexant CX20924
- Micro Controller Unit : Nuvoton MINI54FDE
- RGB LED, Fan, Temp. sensors
- Touch Sensor : Cypress CY8C4014LQI
- RGB LED driver : TI LP55231 (2x)
- LEDs/Keys : 11x, 6x
- UART : through-hole on PCB
- J1: 3.3V, TX, RX, GND from tri-angle marking
- 115200n8
- Power : 12 VDC, 2.5 A
Flash instruction using initramfs image:
1. Prepare TFTP server with the IP address 192.168.132.100 and place the
initramfs image to TFTP directory with the name "C0A88401.img"
2. Boot NCP-HG100/Cellular and interrupt after the message
"Hit any key to stop autoboot: 2"
3. Perform the following commands and set bootcmd to allow booting from
eMMC
setenv bootcmd "mmc read 0x84000000 0x2e22 0x4000 && bootm 0x84000000"
saveenv
4. Perform the following command to load/boot the OpenWrt initramfs image
tftpboot && bootm
5. On the initramfs image, perform sysupgrade with the sysupgrade image
(if needed, backup eMMC partitions by dd command and download to
other place before performing sysupgrade)
6. Wait for ~120 seconds to complete flashing
Known issues:
- There are no drivers for audio-related chips/functions in Linux Kernel
and OpenWrt, they cannot be used.
- There is no driver for MINI54FDE Micro-Controller Unit, customized for
this device by the firmware in the MCU. This chip controls the
following functions, but they cannot be controlled in OpenWrt.
- RGB LED
- Fan
this fan is controlled automatically by MCU by default, without
driver
- Thermal Sensors (2x)
- Currently, there is no driver or tool for CY8C4014LQI and cannot be
controlled. It cannot be exited from "booting mode" and moved to "normal
op mode" after booting. And also, the 4x buttons (mic mute, vol down,
vol up, alexa trigger) connected to the IC cannot be controlled.
- it can be exited from "booting mode" by installing and executing
i2cset command:
opkg update
opkg install i2c-tools
i2cset -y 1 0x14 0xf 1
- There is a connection issue on the control by uqmi for the WWAN module.
But modemmanager can be used without any issues and the use of it is
recommended.
- With the F2FS format, too many errors are reported on erasing eMMC
partition "rootfs_data" while booting:
[ 1.360270] sdhci: Secure Digital Host Controller Interface driver
[ 1.363636] sdhci: Copyright(c) Pierre Ossman
[ 1.369730] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.374729] sdhci_msm 7824900.sdhci: Got CD GPIO
...
[ 1.413552] mmc0: SDHCI controller on 7824900.sdhci [7824900.sdhci] using ADMA 64-bit
[ 1.528325] mmc0: new HS200 MMC card at address 0001
[ 1.530627] mmcblk0: mmc0:0001 004GA0 3.69 GiB
[ 1.533530] mmcblk0boot0: mmc0:0001 004GA0 partition 1 2.00 MiB
[ 1.537831] mmcblk0boot1: mmc0:0001 004GA0 partition 2 2.00 MiB
[ 1.542918] mmcblk0rpmb: mmc0:0001 004GA0 partition 3 512 KiB, chardev (247:0)
[ 1.550323] Alternate GPT is invalid, using primary GPT.
[ 1.561669] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17
...
[ 8.841400] mount_root: loading kmods from internal overlay
[ 8.860241] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 8.863746] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 9.240465] block: attempting to load /etc/config/fstab
[ 9.246722] block: unable to load configuration (fstab: Entry not found)
[ 9.246863] block: no usable configuration
[ 9.254883] mount_root: overlay filesystem in /dev/mmcblk0p17 has not been formatted yet
[ 9.438915] urandom_read: 5 callbacks suppressed
[ 9.438924] random: mkfs.f2fs: uninitialized urandom read (16 bytes read)
[ 12.243332] mmc_erase: erase error -110, status 0x800
[ 12.246638] mmc0: cache flush error -110
[ 15.134585] mmc_erase: erase error -110, status 0x800
[ 15.135891] mmc_erase: group start error -110, status 0x0
[ 15.139850] mmc_erase: group start error -110, status 0x0
...(too many the same errors)...
[ 17.350811] mmc_erase: group start error -110, status 0x0
[ 17.356197] mmc_erase: group start error -110, status 0x0
[ 17.439498] sdhci_msm 7824900.sdhci: Card stuck in wrong state! card_busy_detect status: 0xe00
[ 17.446910] mmc0: tuning execution failed: -5
[ 17.447111] mmc0: cache flush error -110
[ 18.012440] F2FS-fs (mmcblk0p17): Found nat_bits in checkpoint
[ 18.062652] F2FS-fs (mmcblk0p17): Mounted with checkpoint version = 428fa16b
[ 18.198691] block: attempting to load /etc/config/fstab
[ 18.198972] block: unable to load configuration (fstab: Entry not found)
[ 18.203029] block: no usable configuration
[ 18.211371] mount_root: overlay filesystem has not been fully initialized yet
[ 18.214487] mount_root: switching to f2fs overlay
So, this support uses ext4 format instead which has no errors.
Note:
- The primary uart is shared for debug console and Z-Wave chip. The
function is switched by GPIO15 (Linux: 427).
value:
1: debug console
0: Z-Wave
- NCP-HG100/Cellular has 2x os-image pairs in eMMC.
- 0:HLOS, rootfs
- 0:HLOS_1, rootfs_1
In OpenWrt, the first image pair is used.
- "bootipq" command in U-Boot requires authentication with signed-image
by default. To boot unsigned image of OpenWrt, use "mmc read" and
"bootm" command instead.
- This support is for "Cellular" variant of NCP-HG100 and not tested on
"WLAN" (non-cellular) variant.
- The board files of ipq-wifi may also be used in "WLAN" variant of
NCP-HG100, but unconfirmed and add files as for "Cellular" variant.
- "NET" LED is used to indicate WWAN status in stock firmware.
- There is no MAC address information in the label on the case, use the
address included in UUID in the label as "label-MAC" instead.
- The "CLOUD" LEDs are partially used for indication of system status in
stock firmware, use they as status LEDs in OpenWrt instead of RGB LED
connected to the MCU.
MAC addresses:
LAN : 5C:FF:35:**:**:ED (ART, 0x6 (hex))
WAN : 5C:FF:35:**:**:EF (ART, 0x0 (hex))
2.4 GHz: 5C:FF:35:**:**:ED (ART, 0x1006 (hex))
5 GHz : 5C:FF:35:**:**:EE (ART, 0x5006 (hex))
partition layout in eMMC (by fdisk, GPT):
Disk /dev/mmcblk0: 7733248 sectors, 3776M
Logical sector size: 512
Disk identifier (GUID): ****
Partition table holds up to 20 entries
First usable sector is 34, last usable sector is 7634910
Number Start (sector) End (sector) Size Name
1 34 1057 512K 0:SBL1
2 1058 2081 512K 0:BOOTCONFIG
3 2082 3105 512K 0:QSEE
4 3106 4129 512K 0:QSEE_1
5 4130 4641 256K 0:CDT
6 4642 5153 256K 0:CDT_1
7 5154 6177 512K 0:BOOTCONFIG1
8 6178 6689 256K 0:APPSBLENV
9 6690 8737 1024K 0:APPSBL
10 8738 10785 1024K 0:APPSBL_1
11 10786 11297 256K 0:ART
12 11298 11809 256K 0:HSEE
13 11810 28193 8192K 0:HLOS
14 28194 44577 8192K 0:HLOS_1
15 44578 306721 128M rootfs
16 306722 568865 128M rootfs_1
17 568866 3958065 1654M rootfs_data
[initial work]
Signed-off-by: Iwao Yuki <dev.clef@gmail.com>
Co-developed-by: Iwao Yuki <dev.clef@gmail.com>
[adjustments, cleanups, commit message, sending patch]
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
(dropped clk_unused_ignore, dropped 901-* patches, renamed
key nodes, changed LEDs chan/labels to match func-en, made
:net -> (w)wan leds)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-09-04 12:27:11 +00:00
|
|
|
define Device/sony_ncp-hg100-cellular
|
|
|
|
|
$(call Device/FitImage)
|
|
|
|
|
DEVICE_VENDOR := Sony
|
|
|
|
|
DEVICE_MODEL := NCP-HG100/Cellular
|
|
|
|
|
DEVICE_DTS_CONFIG := config@ap.dk04.1-c4
|
|
|
|
|
SOC := qcom-ipq4019
|
|
|
|
|
KERNEL_SIZE := 8192k
|
|
|
|
|
IMAGE_SIZE := 128m
|
2023-05-17 20:02:40 +00:00
|
|
|
DEVICE_PACKAGES := e2fsprogs kmod-fs-ext4 uqmi
|
ipq40xx: add support for Sony NCP-HG100/Cellular
Sony NCP-HG100/Cellular is a IoT Gateway with 2.4/5 GHz band 11ac
(WiFi-5) wireless function, based on IPQ4019.
Specification:
- SoC : Qualcomm IPQ4019
- RAM : DDR3 512 MiB (H5TC4G63EFR)
- Flash : eMMC 4 GiB (THGBMNG5D1LBAIT)
- WLAN : 2.4/5 GHz 2T2R (IPQ4019)
- Ethernet : 10/100/1000 Mbps x2
- Transceiver : Qualcomm QCA8072
- WWAN : Telit LN940A9
- Z-Wave : Silicon Labs ZM5101
- Bluetooth : Qualcomm CSR8811
- Audio DAC : Realtek ALC5629
- Audio Amp. : Realtek ALC1304
- Voice Input Processor : Conexant CX20924
- Micro Controller Unit : Nuvoton MINI54FDE
- RGB LED, Fan, Temp. sensors
- Touch Sensor : Cypress CY8C4014LQI
- RGB LED driver : TI LP55231 (2x)
- LEDs/Keys : 11x, 6x
- UART : through-hole on PCB
- J1: 3.3V, TX, RX, GND from tri-angle marking
- 115200n8
- Power : 12 VDC, 2.5 A
Flash instruction using initramfs image:
1. Prepare TFTP server with the IP address 192.168.132.100 and place the
initramfs image to TFTP directory with the name "C0A88401.img"
2. Boot NCP-HG100/Cellular and interrupt after the message
"Hit any key to stop autoboot: 2"
3. Perform the following commands and set bootcmd to allow booting from
eMMC
setenv bootcmd "mmc read 0x84000000 0x2e22 0x4000 && bootm 0x84000000"
saveenv
4. Perform the following command to load/boot the OpenWrt initramfs image
tftpboot && bootm
5. On the initramfs image, perform sysupgrade with the sysupgrade image
(if needed, backup eMMC partitions by dd command and download to
other place before performing sysupgrade)
6. Wait for ~120 seconds to complete flashing
Known issues:
- There are no drivers for audio-related chips/functions in Linux Kernel
and OpenWrt, they cannot be used.
- There is no driver for MINI54FDE Micro-Controller Unit, customized for
this device by the firmware in the MCU. This chip controls the
following functions, but they cannot be controlled in OpenWrt.
- RGB LED
- Fan
this fan is controlled automatically by MCU by default, without
driver
- Thermal Sensors (2x)
- Currently, there is no driver or tool for CY8C4014LQI and cannot be
controlled. It cannot be exited from "booting mode" and moved to "normal
op mode" after booting. And also, the 4x buttons (mic mute, vol down,
vol up, alexa trigger) connected to the IC cannot be controlled.
- it can be exited from "booting mode" by installing and executing
i2cset command:
opkg update
opkg install i2c-tools
i2cset -y 1 0x14 0xf 1
- There is a connection issue on the control by uqmi for the WWAN module.
But modemmanager can be used without any issues and the use of it is
recommended.
- With the F2FS format, too many errors are reported on erasing eMMC
partition "rootfs_data" while booting:
[ 1.360270] sdhci: Secure Digital Host Controller Interface driver
[ 1.363636] sdhci: Copyright(c) Pierre Ossman
[ 1.369730] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.374729] sdhci_msm 7824900.sdhci: Got CD GPIO
...
[ 1.413552] mmc0: SDHCI controller on 7824900.sdhci [7824900.sdhci] using ADMA 64-bit
[ 1.528325] mmc0: new HS200 MMC card at address 0001
[ 1.530627] mmcblk0: mmc0:0001 004GA0 3.69 GiB
[ 1.533530] mmcblk0boot0: mmc0:0001 004GA0 partition 1 2.00 MiB
[ 1.537831] mmcblk0boot1: mmc0:0001 004GA0 partition 2 2.00 MiB
[ 1.542918] mmcblk0rpmb: mmc0:0001 004GA0 partition 3 512 KiB, chardev (247:0)
[ 1.550323] Alternate GPT is invalid, using primary GPT.
[ 1.561669] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17
...
[ 8.841400] mount_root: loading kmods from internal overlay
[ 8.860241] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 8.863746] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 9.240465] block: attempting to load /etc/config/fstab
[ 9.246722] block: unable to load configuration (fstab: Entry not found)
[ 9.246863] block: no usable configuration
[ 9.254883] mount_root: overlay filesystem in /dev/mmcblk0p17 has not been formatted yet
[ 9.438915] urandom_read: 5 callbacks suppressed
[ 9.438924] random: mkfs.f2fs: uninitialized urandom read (16 bytes read)
[ 12.243332] mmc_erase: erase error -110, status 0x800
[ 12.246638] mmc0: cache flush error -110
[ 15.134585] mmc_erase: erase error -110, status 0x800
[ 15.135891] mmc_erase: group start error -110, status 0x0
[ 15.139850] mmc_erase: group start error -110, status 0x0
...(too many the same errors)...
[ 17.350811] mmc_erase: group start error -110, status 0x0
[ 17.356197] mmc_erase: group start error -110, status 0x0
[ 17.439498] sdhci_msm 7824900.sdhci: Card stuck in wrong state! card_busy_detect status: 0xe00
[ 17.446910] mmc0: tuning execution failed: -5
[ 17.447111] mmc0: cache flush error -110
[ 18.012440] F2FS-fs (mmcblk0p17): Found nat_bits in checkpoint
[ 18.062652] F2FS-fs (mmcblk0p17): Mounted with checkpoint version = 428fa16b
[ 18.198691] block: attempting to load /etc/config/fstab
[ 18.198972] block: unable to load configuration (fstab: Entry not found)
[ 18.203029] block: no usable configuration
[ 18.211371] mount_root: overlay filesystem has not been fully initialized yet
[ 18.214487] mount_root: switching to f2fs overlay
So, this support uses ext4 format instead which has no errors.
Note:
- The primary uart is shared for debug console and Z-Wave chip. The
function is switched by GPIO15 (Linux: 427).
value:
1: debug console
0: Z-Wave
- NCP-HG100/Cellular has 2x os-image pairs in eMMC.
- 0:HLOS, rootfs
- 0:HLOS_1, rootfs_1
In OpenWrt, the first image pair is used.
- "bootipq" command in U-Boot requires authentication with signed-image
by default. To boot unsigned image of OpenWrt, use "mmc read" and
"bootm" command instead.
- This support is for "Cellular" variant of NCP-HG100 and not tested on
"WLAN" (non-cellular) variant.
- The board files of ipq-wifi may also be used in "WLAN" variant of
NCP-HG100, but unconfirmed and add files as for "Cellular" variant.
- "NET" LED is used to indicate WWAN status in stock firmware.
- There is no MAC address information in the label on the case, use the
address included in UUID in the label as "label-MAC" instead.
- The "CLOUD" LEDs are partially used for indication of system status in
stock firmware, use they as status LEDs in OpenWrt instead of RGB LED
connected to the MCU.
MAC addresses:
LAN : 5C:FF:35:**:**:ED (ART, 0x6 (hex))
WAN : 5C:FF:35:**:**:EF (ART, 0x0 (hex))
2.4 GHz: 5C:FF:35:**:**:ED (ART, 0x1006 (hex))
5 GHz : 5C:FF:35:**:**:EE (ART, 0x5006 (hex))
partition layout in eMMC (by fdisk, GPT):
Disk /dev/mmcblk0: 7733248 sectors, 3776M
Logical sector size: 512
Disk identifier (GUID): ****
Partition table holds up to 20 entries
First usable sector is 34, last usable sector is 7634910
Number Start (sector) End (sector) Size Name
1 34 1057 512K 0:SBL1
2 1058 2081 512K 0:BOOTCONFIG
3 2082 3105 512K 0:QSEE
4 3106 4129 512K 0:QSEE_1
5 4130 4641 256K 0:CDT
6 4642 5153 256K 0:CDT_1
7 5154 6177 512K 0:BOOTCONFIG1
8 6178 6689 256K 0:APPSBLENV
9 6690 8737 1024K 0:APPSBL
10 8738 10785 1024K 0:APPSBL_1
11 10786 11297 256K 0:ART
12 11298 11809 256K 0:HSEE
13 11810 28193 8192K 0:HLOS
14 28194 44577 8192K 0:HLOS_1
15 44578 306721 128M rootfs
16 306722 568865 128M rootfs_1
17 568866 3958065 1654M rootfs_data
[initial work]
Signed-off-by: Iwao Yuki <dev.clef@gmail.com>
Co-developed-by: Iwao Yuki <dev.clef@gmail.com>
[adjustments, cleanups, commit message, sending patch]
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
(dropped clk_unused_ignore, dropped 901-* patches, renamed
key nodes, changed LEDs chan/labels to match func-en, made
:net -> (w)wan leds)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-09-04 12:27:11 +00:00
|
|
|
endef
|
2022-10-05 14:35:21 +00:00
|
|
|
TARGET_DEVICES += sony_ncp-hg100-cellular
|
ipq40xx: add support for Sony NCP-HG100/Cellular
Sony NCP-HG100/Cellular is a IoT Gateway with 2.4/5 GHz band 11ac
(WiFi-5) wireless function, based on IPQ4019.
Specification:
- SoC : Qualcomm IPQ4019
- RAM : DDR3 512 MiB (H5TC4G63EFR)
- Flash : eMMC 4 GiB (THGBMNG5D1LBAIT)
- WLAN : 2.4/5 GHz 2T2R (IPQ4019)
- Ethernet : 10/100/1000 Mbps x2
- Transceiver : Qualcomm QCA8072
- WWAN : Telit LN940A9
- Z-Wave : Silicon Labs ZM5101
- Bluetooth : Qualcomm CSR8811
- Audio DAC : Realtek ALC5629
- Audio Amp. : Realtek ALC1304
- Voice Input Processor : Conexant CX20924
- Micro Controller Unit : Nuvoton MINI54FDE
- RGB LED, Fan, Temp. sensors
- Touch Sensor : Cypress CY8C4014LQI
- RGB LED driver : TI LP55231 (2x)
- LEDs/Keys : 11x, 6x
- UART : through-hole on PCB
- J1: 3.3V, TX, RX, GND from tri-angle marking
- 115200n8
- Power : 12 VDC, 2.5 A
Flash instruction using initramfs image:
1. Prepare TFTP server with the IP address 192.168.132.100 and place the
initramfs image to TFTP directory with the name "C0A88401.img"
2. Boot NCP-HG100/Cellular and interrupt after the message
"Hit any key to stop autoboot: 2"
3. Perform the following commands and set bootcmd to allow booting from
eMMC
setenv bootcmd "mmc read 0x84000000 0x2e22 0x4000 && bootm 0x84000000"
saveenv
4. Perform the following command to load/boot the OpenWrt initramfs image
tftpboot && bootm
5. On the initramfs image, perform sysupgrade with the sysupgrade image
(if needed, backup eMMC partitions by dd command and download to
other place before performing sysupgrade)
6. Wait for ~120 seconds to complete flashing
Known issues:
- There are no drivers for audio-related chips/functions in Linux Kernel
and OpenWrt, they cannot be used.
- There is no driver for MINI54FDE Micro-Controller Unit, customized for
this device by the firmware in the MCU. This chip controls the
following functions, but they cannot be controlled in OpenWrt.
- RGB LED
- Fan
this fan is controlled automatically by MCU by default, without
driver
- Thermal Sensors (2x)
- Currently, there is no driver or tool for CY8C4014LQI and cannot be
controlled. It cannot be exited from "booting mode" and moved to "normal
op mode" after booting. And also, the 4x buttons (mic mute, vol down,
vol up, alexa trigger) connected to the IC cannot be controlled.
- it can be exited from "booting mode" by installing and executing
i2cset command:
opkg update
opkg install i2c-tools
i2cset -y 1 0x14 0xf 1
- There is a connection issue on the control by uqmi for the WWAN module.
But modemmanager can be used without any issues and the use of it is
recommended.
- With the F2FS format, too many errors are reported on erasing eMMC
partition "rootfs_data" while booting:
[ 1.360270] sdhci: Secure Digital Host Controller Interface driver
[ 1.363636] sdhci: Copyright(c) Pierre Ossman
[ 1.369730] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.374729] sdhci_msm 7824900.sdhci: Got CD GPIO
...
[ 1.413552] mmc0: SDHCI controller on 7824900.sdhci [7824900.sdhci] using ADMA 64-bit
[ 1.528325] mmc0: new HS200 MMC card at address 0001
[ 1.530627] mmcblk0: mmc0:0001 004GA0 3.69 GiB
[ 1.533530] mmcblk0boot0: mmc0:0001 004GA0 partition 1 2.00 MiB
[ 1.537831] mmcblk0boot1: mmc0:0001 004GA0 partition 2 2.00 MiB
[ 1.542918] mmcblk0rpmb: mmc0:0001 004GA0 partition 3 512 KiB, chardev (247:0)
[ 1.550323] Alternate GPT is invalid, using primary GPT.
[ 1.561669] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17
...
[ 8.841400] mount_root: loading kmods from internal overlay
[ 8.860241] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 8.863746] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 9.240465] block: attempting to load /etc/config/fstab
[ 9.246722] block: unable to load configuration (fstab: Entry not found)
[ 9.246863] block: no usable configuration
[ 9.254883] mount_root: overlay filesystem in /dev/mmcblk0p17 has not been formatted yet
[ 9.438915] urandom_read: 5 callbacks suppressed
[ 9.438924] random: mkfs.f2fs: uninitialized urandom read (16 bytes read)
[ 12.243332] mmc_erase: erase error -110, status 0x800
[ 12.246638] mmc0: cache flush error -110
[ 15.134585] mmc_erase: erase error -110, status 0x800
[ 15.135891] mmc_erase: group start error -110, status 0x0
[ 15.139850] mmc_erase: group start error -110, status 0x0
...(too many the same errors)...
[ 17.350811] mmc_erase: group start error -110, status 0x0
[ 17.356197] mmc_erase: group start error -110, status 0x0
[ 17.439498] sdhci_msm 7824900.sdhci: Card stuck in wrong state! card_busy_detect status: 0xe00
[ 17.446910] mmc0: tuning execution failed: -5
[ 17.447111] mmc0: cache flush error -110
[ 18.012440] F2FS-fs (mmcblk0p17): Found nat_bits in checkpoint
[ 18.062652] F2FS-fs (mmcblk0p17): Mounted with checkpoint version = 428fa16b
[ 18.198691] block: attempting to load /etc/config/fstab
[ 18.198972] block: unable to load configuration (fstab: Entry not found)
[ 18.203029] block: no usable configuration
[ 18.211371] mount_root: overlay filesystem has not been fully initialized yet
[ 18.214487] mount_root: switching to f2fs overlay
So, this support uses ext4 format instead which has no errors.
Note:
- The primary uart is shared for debug console and Z-Wave chip. The
function is switched by GPIO15 (Linux: 427).
value:
1: debug console
0: Z-Wave
- NCP-HG100/Cellular has 2x os-image pairs in eMMC.
- 0:HLOS, rootfs
- 0:HLOS_1, rootfs_1
In OpenWrt, the first image pair is used.
- "bootipq" command in U-Boot requires authentication with signed-image
by default. To boot unsigned image of OpenWrt, use "mmc read" and
"bootm" command instead.
- This support is for "Cellular" variant of NCP-HG100 and not tested on
"WLAN" (non-cellular) variant.
- The board files of ipq-wifi may also be used in "WLAN" variant of
NCP-HG100, but unconfirmed and add files as for "Cellular" variant.
- "NET" LED is used to indicate WWAN status in stock firmware.
- There is no MAC address information in the label on the case, use the
address included in UUID in the label as "label-MAC" instead.
- The "CLOUD" LEDs are partially used for indication of system status in
stock firmware, use they as status LEDs in OpenWrt instead of RGB LED
connected to the MCU.
MAC addresses:
LAN : 5C:FF:35:**:**:ED (ART, 0x6 (hex))
WAN : 5C:FF:35:**:**:EF (ART, 0x0 (hex))
2.4 GHz: 5C:FF:35:**:**:ED (ART, 0x1006 (hex))
5 GHz : 5C:FF:35:**:**:EE (ART, 0x5006 (hex))
partition layout in eMMC (by fdisk, GPT):
Disk /dev/mmcblk0: 7733248 sectors, 3776M
Logical sector size: 512
Disk identifier (GUID): ****
Partition table holds up to 20 entries
First usable sector is 34, last usable sector is 7634910
Number Start (sector) End (sector) Size Name
1 34 1057 512K 0:SBL1
2 1058 2081 512K 0:BOOTCONFIG
3 2082 3105 512K 0:QSEE
4 3106 4129 512K 0:QSEE_1
5 4130 4641 256K 0:CDT
6 4642 5153 256K 0:CDT_1
7 5154 6177 512K 0:BOOTCONFIG1
8 6178 6689 256K 0:APPSBLENV
9 6690 8737 1024K 0:APPSBL
10 8738 10785 1024K 0:APPSBL_1
11 10786 11297 256K 0:ART
12 11298 11809 256K 0:HSEE
13 11810 28193 8192K 0:HLOS
14 28194 44577 8192K 0:HLOS_1
15 44578 306721 128M rootfs
16 306722 568865 128M rootfs_1
17 568866 3958065 1654M rootfs_data
[initial work]
Signed-off-by: Iwao Yuki <dev.clef@gmail.com>
Co-developed-by: Iwao Yuki <dev.clef@gmail.com>
[adjustments, cleanups, commit message, sending patch]
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
(dropped clk_unused_ignore, dropped 901-* patches, renamed
key nodes, changed LEDs chan/labels to match func-en, made
:net -> (w)wan leds)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-09-04 12:27:11 +00:00
|
|
|
|
2021-07-15 19:48:11 +00:00
|
|
|
define Device/teltonika_rutx10
|
|
|
|
|
$(call Device/FitImage)
|
|
|
|
|
$(call Device/UbiFit)
|
|
|
|
|
DEVICE_VENDOR := Teltonika
|
|
|
|
|
DEVICE_MODEL := RUTX10
|
|
|
|
|
SOC := qcom-ipq4018
|
|
|
|
|
DEVICE_DTS_CONFIG := config@5
|
|
|
|
|
KERNEL_INSTALL := 1
|
|
|
|
|
BLOCKSIZE := 128k
|
|
|
|
|
PAGESIZE := 2048
|
|
|
|
|
FILESYSTEMS := squashfs
|
2022-11-17 01:52:50 +00:00
|
|
|
IMAGE/factory.ubi := append-ubi | qsdk-ipq-factory-nand | append-rutx-metadata
|
2023-05-17 20:02:40 +00:00
|
|
|
DEVICE_PACKAGES := kmod-bluetooth
|
2021-07-15 19:48:11 +00:00
|
|
|
endef
|
2022-09-28 15:42:48 +00:00
|
|
|
# Missing DSA Setup
|
|
|
|
|
#TARGET_DEVICES += teltonika_rutx10
|
2021-07-15 19:48:11 +00:00
|
|
|
|
2022-03-11 03:54:07 +00:00
|
|
|
define Device/tel_x1pro
|
|
|
|
|
$(call Device/FitImage)
|
|
|
|
|
DEVICE_VENDOR := Telco
|
|
|
|
|
DEVICE_MODEL := X1 Pro
|
|
|
|
|
SOC := qcom-ipq4019
|
|
|
|
|
KERNEL_SIZE := 4096k
|
|
|
|
|
IMAGE_SIZE := 31232k
|
|
|
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
|
|
|
|
DEVICE_PACKAGES := kmod-usb-net-qmi-wwan kmod-usb-serial-option uqmi
|
2022-03-24 19:34:16 +00:00
|
|
|
DEFAULT := n
|
2022-03-11 03:54:07 +00:00
|
|
|
endef
|
2022-09-28 15:42:48 +00:00
|
|
|
# Missing DSA Setup
|
|
|
|
|
#TARGET_DEVICES += tel_x1pro
|
2022-03-11 03:54:07 +00:00
|
|
|
|
2021-01-17 05:54:04 +00:00
|
|
|
define Device/unielec_u4019-32m
|
|
|
|
|
$(call Device/FitImage)
|
|
|
|
|
DEVICE_VENDOR := Unielec
|
|
|
|
|
DEVICE_MODEL := U4019
|
|
|
|
|
DEVICE_VARIANT := 32M
|
|
|
|
|
BOARD_NAME := u4019-32m
|
|
|
|
|
SOC := qcom-ipq4019
|
|
|
|
|
KERNEL_SIZE := 4096k
|
|
|
|
|
IMAGE_SIZE := 31232k
|
|
|
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
2021-11-03 15:45:38 +00:00
|
|
|
DEFAULT := n
|
2021-01-17 05:54:04 +00:00
|
|
|
endef
|
2022-09-28 15:42:48 +00:00
|
|
|
# Missing DSA Setup
|
|
|
|
|
#TARGET_DEVICES += unielec_u4019-32m
|
2021-01-17 05:54:04 +00:00
|
|
|
|
2020-06-30 16:07:50 +00:00
|
|
|
define Device/wallys_dr40x9
|
|
|
|
|
$(call Device/FitImage)
|
|
|
|
|
$(call Device/UbiFit)
|
|
|
|
|
DEVICE_VENDOR := Wallys
|
|
|
|
|
DEVICE_MODEL := DR40X9
|
|
|
|
|
SOC := qcom-ipq40x9
|
|
|
|
|
DEVICE_DTS_CONFIG := config@ap.dk07.1-c1
|
|
|
|
|
BLOCKSIZE := 128k
|
|
|
|
|
PAGESIZE := 2048
|
|
|
|
|
DEVICE_PACKAGES := ipq-wifi-wallys_dr40x9
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += wallys_dr40x9
|
|
|
|
|
|
ipq40xx: Add support ZTE MF18A
Light and small router ( In Poland operators sells together with MC7010 outdoor modem to provide WIFI inside home).
Device specification
SoC Type: Qualcomm IPQ4019
RAM: 256 MiB
Flash: 128 MiB SPI NAND (Winbond W25N01GV)
ROM: 2MiB SPI Flash (GD25Q16)
Wireless 2.4 GHz (IP4019): b/g/n, 2x2
Wireless 5 GHz (QCA9982): a/n/ac, 3x3
Ethernet: 2xGbE (WAN/LAN1, LAN2)
USB ports: No
Button: 2 (Reset/WPS)
LEDs: 3 external leds: Power (blue) , WiFI (blue and red), SMARTHOME (blue and red) and 1 internal (blue) -- NOTE: Power controls all external led (if down ,all others also not lights even signal is up)
Power: 5VDC, 2,1A via USB-C socket
Bootloader: U-Boot
On board ZWave and Zigbee (EFR32 MG1P232GG..) modules ( not supported by orginal software )
Installation
1.Open MF18A case by ungluing rubber pad under the router and unscrew screws, and connect to serial console port,
with the following pinout, starting from pin 1, which is the topmost pin when the board is upright (reset button on the bottom) :
VCC (3.3V). Do not use unless you need to source power for the converer from it.
TX
RX
GND
Default port configuration in U-boot as well as in stock firmware is 115200-8-N-1.
2.Place OpenWrt initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2
3.Connect TFTP server to RJ-45 port (WAN/LAN1).
4.Power on MF18A , stop in u-Boot (using ESC button) and run u-Boot commands:
setenv serverip 192.168.0.2
setenv ipaddr 192.168.0.1
set fdt_high 0x85000000
tftpboot 0x84000000 openwrt-ipq40xx-generic-zte_mf18a-initramfs-fit-zImage.itb
bootm 0x84000000
5.Please make backup of original partitions, if you think about revert to stock, specially mtd8 (Web UI) and mtd9 (rootFS). Use /tmp as temporary storage and do:
WEB PARITION
cat /dev/mtd8 > /tmp/mtd8.bin
scp /tmp/mtd8.bin root@YOURSERVERIP:/
rm /tmp/mtd8.bin
ROOT PARITION
cat /dev/mtd9 > /tmp/mtd9.bin
scp /tmp/mtd9.bin root@YOURSERVERIP:/
rm /tmp/mtd9.bin
If you are sure ,that you want to flash openwrt, from uBoot, before bootm, clean rootfs partition with command:
nand erase 0x1800000 0x1D00000
6.Login via ssh or serial and remove stock partitions (default IP 192.168.1.1):
ubiattach -m 9 # it could return error if ubi was attached before or rootfs part was erased before
ubirmvol /dev/ubi0 -N ubi_rootfs # it could return error if rootfs part was erased before
ubirmvol /dev/ubi0 -N ubi_rootfs_data # some devices doesn't have it
7. Install image via :
sysupgrade -n /tmp/openwrt-ipq40xx-generic-zte_mf18a-squashfs-sysupgrade.bin
previously wgeting bin. Sometimes it could print ubi attach error, but please ignore it if process goes forward.
Back to Stock (!!! need original dump taken from initramfs !!!) -------------
Place mtd8.bin and mtd9.bin initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2
Connect serial console (115200,8n1) to serial console connector .
Connect TFTP server to RJ-45 port (WAN/LAN1).
rename mtd8.bin to web.img and mtd9.bin to root_uImage_s
Stop in u-Boot (using ESC button) and run u-Boot commands:
This will erase Web and RootFS:
nand erase 0x1000000 0x800000
nand erase 0x1800000 0x1D00000
This will restore RootFS:
tftpboot 0x84000000 root_uImage_s
nand erase 0x1800000 0x1D00000
nand write 0x84000000 0x1800000 0x1D00000
This will restore Web Interface:
tftpboot 0x84000000 web.img
nand erase 0x1000000 0x800000
nand write 0x84000000 0x1000000 0x800000
After first boot on stock firwmare, do a factory reset. Push reset button for 5 seconds so all parameters will be reverted to the one printed on label on bottom of the router
As reference was taken MF289F support by Giammarco Marzano stich86@gmail.com and MF286D by Pawel Dembicki paweldembicki@gmail.com
Signed-off-by: Marcin Gajda <mgajda@o2.pl>
2022-12-28 18:01:40 +00:00
|
|
|
define Device/zte_mf18a
|
|
|
|
|
$(call Device/FitImage)
|
|
|
|
|
DEVICE_VENDOR := ZTE
|
|
|
|
|
DEVICE_MODEL := MF18A
|
|
|
|
|
SOC := qcom-ipq4019
|
|
|
|
|
DEVICE_DTS_CONFIG := config@ap.dk04.1-c1
|
|
|
|
|
BLOCKSIZE := 128k
|
|
|
|
|
PAGESIZE := 2048
|
|
|
|
|
KERNEL_IN_UBI := 1
|
2023-05-17 20:02:40 +00:00
|
|
|
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
|
ipq40xx: Add support ZTE MF18A
Light and small router ( In Poland operators sells together with MC7010 outdoor modem to provide WIFI inside home).
Device specification
SoC Type: Qualcomm IPQ4019
RAM: 256 MiB
Flash: 128 MiB SPI NAND (Winbond W25N01GV)
ROM: 2MiB SPI Flash (GD25Q16)
Wireless 2.4 GHz (IP4019): b/g/n, 2x2
Wireless 5 GHz (QCA9982): a/n/ac, 3x3
Ethernet: 2xGbE (WAN/LAN1, LAN2)
USB ports: No
Button: 2 (Reset/WPS)
LEDs: 3 external leds: Power (blue) , WiFI (blue and red), SMARTHOME (blue and red) and 1 internal (blue) -- NOTE: Power controls all external led (if down ,all others also not lights even signal is up)
Power: 5VDC, 2,1A via USB-C socket
Bootloader: U-Boot
On board ZWave and Zigbee (EFR32 MG1P232GG..) modules ( not supported by orginal software )
Installation
1.Open MF18A case by ungluing rubber pad under the router and unscrew screws, and connect to serial console port,
with the following pinout, starting from pin 1, which is the topmost pin when the board is upright (reset button on the bottom) :
VCC (3.3V). Do not use unless you need to source power for the converer from it.
TX
RX
GND
Default port configuration in U-boot as well as in stock firmware is 115200-8-N-1.
2.Place OpenWrt initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2
3.Connect TFTP server to RJ-45 port (WAN/LAN1).
4.Power on MF18A , stop in u-Boot (using ESC button) and run u-Boot commands:
setenv serverip 192.168.0.2
setenv ipaddr 192.168.0.1
set fdt_high 0x85000000
tftpboot 0x84000000 openwrt-ipq40xx-generic-zte_mf18a-initramfs-fit-zImage.itb
bootm 0x84000000
5.Please make backup of original partitions, if you think about revert to stock, specially mtd8 (Web UI) and mtd9 (rootFS). Use /tmp as temporary storage and do:
WEB PARITION
cat /dev/mtd8 > /tmp/mtd8.bin
scp /tmp/mtd8.bin root@YOURSERVERIP:/
rm /tmp/mtd8.bin
ROOT PARITION
cat /dev/mtd9 > /tmp/mtd9.bin
scp /tmp/mtd9.bin root@YOURSERVERIP:/
rm /tmp/mtd9.bin
If you are sure ,that you want to flash openwrt, from uBoot, before bootm, clean rootfs partition with command:
nand erase 0x1800000 0x1D00000
6.Login via ssh or serial and remove stock partitions (default IP 192.168.1.1):
ubiattach -m 9 # it could return error if ubi was attached before or rootfs part was erased before
ubirmvol /dev/ubi0 -N ubi_rootfs # it could return error if rootfs part was erased before
ubirmvol /dev/ubi0 -N ubi_rootfs_data # some devices doesn't have it
7. Install image via :
sysupgrade -n /tmp/openwrt-ipq40xx-generic-zte_mf18a-squashfs-sysupgrade.bin
previously wgeting bin. Sometimes it could print ubi attach error, but please ignore it if process goes forward.
Back to Stock (!!! need original dump taken from initramfs !!!) -------------
Place mtd8.bin and mtd9.bin initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2
Connect serial console (115200,8n1) to serial console connector .
Connect TFTP server to RJ-45 port (WAN/LAN1).
rename mtd8.bin to web.img and mtd9.bin to root_uImage_s
Stop in u-Boot (using ESC button) and run u-Boot commands:
This will erase Web and RootFS:
nand erase 0x1000000 0x800000
nand erase 0x1800000 0x1D00000
This will restore RootFS:
tftpboot 0x84000000 root_uImage_s
nand erase 0x1800000 0x1D00000
nand write 0x84000000 0x1800000 0x1D00000
This will restore Web Interface:
tftpboot 0x84000000 web.img
nand erase 0x1000000 0x800000
nand write 0x84000000 0x1000000 0x800000
After first boot on stock firwmare, do a factory reset. Push reset button for 5 seconds so all parameters will be reverted to the one printed on label on bottom of the router
As reference was taken MF289F support by Giammarco Marzano stich86@gmail.com and MF286D by Pawel Dembicki paweldembicki@gmail.com
Signed-off-by: Marcin Gajda <mgajda@o2.pl>
2022-12-28 18:01:40 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += zte_mf18a
|
|
|
|
|
|
ipq40xx: Add ZTE MF289F
It's a 4G Cat.20 router used by Vodafone Italy (called Vodafone FWA)
and Vodafone DE\T-Mobile PL (called GigaCube).
Modem is a MiniPCIe-to-USB based on Snapdragon X24,
it supports 4CA aggregation.
There are currently two hardware revisions, which
differ on the 5Ghz radio:
AT1 = QCA9984 5Ghz Radio on PCI-E bus
AT2 = IPQ4019 5Ghz Radio inside IPQ4019 like 2.4Ghz
Device specification
--------------------
SoC Type: Qualcomm IPQ4019
RAM: 256 MiB
Flash: 128 MiB SPI NAND (Winbond W25N01GV)
ROM: 2MiB SPI Flash (GD25Q16)
Wireless 2.4 GHz (IP4019): b/g/n, 2x2
Wireless 5 GHz:
(QCA9984): a/n/ac, 4x4 HW REV AT1
(IPA4019): a/n/ac, 2x2 HW REV AT2
Ethernet: 2xGbE (WAN/LAN1, LAN2)
USB ports: No
Button: 2 (Reset/WPS)
LEDs: 3 external leds: Network (white or red), Wifi, Power and 1 internal (blue)
Power: 12 VDC, 1 A
Connector type: Barrel
Bootloader: U-Boot
Installation
------------
1. Place OpenWrt initramfs image for the device on a TFTP
in the server's root. This example uses Server IP: 192.168.0.2
2. Connect serial console (115200,8n1) to serial connector
GND (which is right next to the thing with MF289F MIMO-V1.0), RX, TX
(refer to this image: https://ibb.co/31Gngpr).
3. Connect TFTP server to RJ-45 port (WAN/LAN1).
4. Stop in u-Boot (using ESC button) and run u-Boot commands:
setenv serverip 192.168.0.2
setenv ipaddr 192.168.0.1
set fdt_high 0x85000000
tftp openwrt-ipq40xx-generic-zte_mf289f-initramfs-fit-zImage.itb
bootm $loadaddr
5. Please make backup of original partitions, if you think about revert to
stock, specially mtd16 (Web UI) and mtd17 (rootFS).
Use /tmp as temporary storage and do:
WEB PARITION
--------------------------------------
cat /dev/mtd16 > /tmp/mtd16.bin
scp /tmp/mtd16.bin root@YOURSERVERIP:/
rm /tmp/mtd16.bin
ROOT PARITION
--------------------------------------
cat /dev/mtd17 > /tmp/mtd17.bin
scp /tmp/mtd17.bin root@YOURSERVERIP:/
rm /tmp/mtd17.bin
6. Login via ssh or serial and remove stock partitions
(default IP 192.168.0.1):
# this can return an error, if ubi was attached before
# or rootfs part was erased before.
ubiattach -m 17
# it could return error if rootfs part was erased before
ubirmvol /dev/ubi0 -N ubi_rootfs
# some devices doesn't have it
ubirmvol /dev/ubi0 -N ubi_rootfs_data
7. download and install image via sysupgrade -n
(either use wget/scp to copy the mf289f's squashfs-sysupgrade.bin
to the device's /tmp directory)
sysupgrade -n /tmp/openwrt-...-zte_mf289f-squashfs-sysupgrade.bin
Sometimes it could print ubi attach error, but please ignore it
if process goes forward.
Flash Layout
NAND:
mtd8: 000a0000 00020000 "fota-flag"
mtd9: 00080000 00020000 "0:ART"
mtd10: 00080000 00020000 "mac"
mtd11: 000c0000 00020000 "reserved2"
mtd12: 00400000 00020000 "cfg-param"
mtd13: 00400000 00020000 "log"
mtd14: 000a0000 00020000 "oops"
mtd15: 00500000 00020000 "reserved3"
mtd16: 00800000 00020000 "web"
mtd17: 01d00000 00020000 "rootfs"
mtd18: 01900000 00020000 "data"
mtd19: 03200000 00020000 "fota"
mtd20: 0041e000 0001f000 "kernel"
mtd21: 0101b000 0001f000 "ubi_rootfs"
SPI:
mtd0: 00040000 00010000 "0:SBL1"
mtd1: 00020000 00010000 "0:MIBIB"
mtd2: 00060000 00010000 "0:QSEE"
mtd3: 00010000 00010000 "0:CDT"
mtd4: 00010000 00010000 "0:DDRPARAMS"
mtd5: 00010000 00010000 "0:APPSBLENV"
mtd6: 000c0000 00010000 "0:APPSBL"
mtd7: 00050000 00010000 "0:reserved1"
Back to Stock (!!! need original dump taken from initramfs !!!)
-------------
1. Place mtd16.bin and mtd17.bin initramfs image
for the device on a TFTP in the server's root.
This example uses Server IP: 192.168.0.2
2. Connect serial console (115200,8n1) to serial console
connector (refer to the pin-out from above).
3. Connect TFTP server to RJ-45 port (WAN/LAN1).
4. rename mtd16.bin to web.img and mtd17.bin to root_uImage_s
5. Stop in u-Boot (using ESC button) and run u-Boot commands:
This will erase RootFS+Web:
nand erase 0x1000000 0x800000
nand erase 0x1800000 0x1D00000
This will restore RootFS:
tftpboot 0x84000000 ${dir}root_uImage_s
nand erase 0x1800000 0x1D00000
nand write $fileaddr 0x1800000 $filesize
This will restore Web Interface:
tftpboot 0x84000000 ${dir}web.img
nand erase 0x1000000 0x800000
nand write $fileaddr 0x1000000 $filesize
After first boot on stock firwmare, do a factory reset.
Push reset button for 5 seconds so all parameters will
be reverted to the one printed on label on bottom of the router
Signed-off-by: Giammarco Marzano <stich86@gmail.com>
Reviewed-by: Lech Perczak <lech.perczak@gmail.com>
(Warning: commit message did not conform to UTF-8 - hopefully fixed?,
added description of the pin-out if image goes down, reformatted
commit message to be hopefully somewhat readable on git-web,
redid some of the gpio-buttons & leds DT nodes, etc.)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-09-14 12:20:43 +00:00
|
|
|
define Device/zte_mf28x_common
|
2021-11-23 08:10:14 +00:00
|
|
|
$(call Device/FitzImage)
|
|
|
|
|
DEVICE_VENDOR := ZTE
|
|
|
|
|
SOC := qcom-ipq4019
|
|
|
|
|
DEVICE_DTS_CONFIG := config@ap.dk04.1-c1
|
|
|
|
|
BLOCKSIZE := 128k
|
|
|
|
|
PAGESIZE := 2048
|
|
|
|
|
KERNEL_IN_UBI := 1
|
2022-05-13 20:25:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-usb-net-qmi-wwan kmod-usb-serial-option uqmi
|
2021-11-23 08:10:14 +00:00
|
|
|
endef
|
ipq40xx: Add ZTE MF289F
It's a 4G Cat.20 router used by Vodafone Italy (called Vodafone FWA)
and Vodafone DE\T-Mobile PL (called GigaCube).
Modem is a MiniPCIe-to-USB based on Snapdragon X24,
it supports 4CA aggregation.
There are currently two hardware revisions, which
differ on the 5Ghz radio:
AT1 = QCA9984 5Ghz Radio on PCI-E bus
AT2 = IPQ4019 5Ghz Radio inside IPQ4019 like 2.4Ghz
Device specification
--------------------
SoC Type: Qualcomm IPQ4019
RAM: 256 MiB
Flash: 128 MiB SPI NAND (Winbond W25N01GV)
ROM: 2MiB SPI Flash (GD25Q16)
Wireless 2.4 GHz (IP4019): b/g/n, 2x2
Wireless 5 GHz:
(QCA9984): a/n/ac, 4x4 HW REV AT1
(IPA4019): a/n/ac, 2x2 HW REV AT2
Ethernet: 2xGbE (WAN/LAN1, LAN2)
USB ports: No
Button: 2 (Reset/WPS)
LEDs: 3 external leds: Network (white or red), Wifi, Power and 1 internal (blue)
Power: 12 VDC, 1 A
Connector type: Barrel
Bootloader: U-Boot
Installation
------------
1. Place OpenWrt initramfs image for the device on a TFTP
in the server's root. This example uses Server IP: 192.168.0.2
2. Connect serial console (115200,8n1) to serial connector
GND (which is right next to the thing with MF289F MIMO-V1.0), RX, TX
(refer to this image: https://ibb.co/31Gngpr).
3. Connect TFTP server to RJ-45 port (WAN/LAN1).
4. Stop in u-Boot (using ESC button) and run u-Boot commands:
setenv serverip 192.168.0.2
setenv ipaddr 192.168.0.1
set fdt_high 0x85000000
tftp openwrt-ipq40xx-generic-zte_mf289f-initramfs-fit-zImage.itb
bootm $loadaddr
5. Please make backup of original partitions, if you think about revert to
stock, specially mtd16 (Web UI) and mtd17 (rootFS).
Use /tmp as temporary storage and do:
WEB PARITION
--------------------------------------
cat /dev/mtd16 > /tmp/mtd16.bin
scp /tmp/mtd16.bin root@YOURSERVERIP:/
rm /tmp/mtd16.bin
ROOT PARITION
--------------------------------------
cat /dev/mtd17 > /tmp/mtd17.bin
scp /tmp/mtd17.bin root@YOURSERVERIP:/
rm /tmp/mtd17.bin
6. Login via ssh or serial and remove stock partitions
(default IP 192.168.0.1):
# this can return an error, if ubi was attached before
# or rootfs part was erased before.
ubiattach -m 17
# it could return error if rootfs part was erased before
ubirmvol /dev/ubi0 -N ubi_rootfs
# some devices doesn't have it
ubirmvol /dev/ubi0 -N ubi_rootfs_data
7. download and install image via sysupgrade -n
(either use wget/scp to copy the mf289f's squashfs-sysupgrade.bin
to the device's /tmp directory)
sysupgrade -n /tmp/openwrt-...-zte_mf289f-squashfs-sysupgrade.bin
Sometimes it could print ubi attach error, but please ignore it
if process goes forward.
Flash Layout
NAND:
mtd8: 000a0000 00020000 "fota-flag"
mtd9: 00080000 00020000 "0:ART"
mtd10: 00080000 00020000 "mac"
mtd11: 000c0000 00020000 "reserved2"
mtd12: 00400000 00020000 "cfg-param"
mtd13: 00400000 00020000 "log"
mtd14: 000a0000 00020000 "oops"
mtd15: 00500000 00020000 "reserved3"
mtd16: 00800000 00020000 "web"
mtd17: 01d00000 00020000 "rootfs"
mtd18: 01900000 00020000 "data"
mtd19: 03200000 00020000 "fota"
mtd20: 0041e000 0001f000 "kernel"
mtd21: 0101b000 0001f000 "ubi_rootfs"
SPI:
mtd0: 00040000 00010000 "0:SBL1"
mtd1: 00020000 00010000 "0:MIBIB"
mtd2: 00060000 00010000 "0:QSEE"
mtd3: 00010000 00010000 "0:CDT"
mtd4: 00010000 00010000 "0:DDRPARAMS"
mtd5: 00010000 00010000 "0:APPSBLENV"
mtd6: 000c0000 00010000 "0:APPSBL"
mtd7: 00050000 00010000 "0:reserved1"
Back to Stock (!!! need original dump taken from initramfs !!!)
-------------
1. Place mtd16.bin and mtd17.bin initramfs image
for the device on a TFTP in the server's root.
This example uses Server IP: 192.168.0.2
2. Connect serial console (115200,8n1) to serial console
connector (refer to the pin-out from above).
3. Connect TFTP server to RJ-45 port (WAN/LAN1).
4. rename mtd16.bin to web.img and mtd17.bin to root_uImage_s
5. Stop in u-Boot (using ESC button) and run u-Boot commands:
This will erase RootFS+Web:
nand erase 0x1000000 0x800000
nand erase 0x1800000 0x1D00000
This will restore RootFS:
tftpboot 0x84000000 ${dir}root_uImage_s
nand erase 0x1800000 0x1D00000
nand write $fileaddr 0x1800000 $filesize
This will restore Web Interface:
tftpboot 0x84000000 ${dir}web.img
nand erase 0x1000000 0x800000
nand write $fileaddr 0x1000000 $filesize
After first boot on stock firwmare, do a factory reset.
Push reset button for 5 seconds so all parameters will
be reverted to the one printed on label on bottom of the router
Signed-off-by: Giammarco Marzano <stich86@gmail.com>
Reviewed-by: Lech Perczak <lech.perczak@gmail.com>
(Warning: commit message did not conform to UTF-8 - hopefully fixed?,
added description of the pin-out if image goes down, reformatted
commit message to be hopefully somewhat readable on git-web,
redid some of the gpio-buttons & leds DT nodes, etc.)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-09-14 12:20:43 +00:00
|
|
|
|
|
|
|
|
define Device/zte_mf286d
|
|
|
|
|
$(call Device/zte_mf28x_common)
|
|
|
|
|
DEVICE_MODEL := MF286D
|
|
|
|
|
endef
|
2021-11-23 08:10:14 +00:00
|
|
|
TARGET_DEVICES += zte_mf286d
|
|
|
|
|
|
ipq40xx: Add ZTE MF289F
It's a 4G Cat.20 router used by Vodafone Italy (called Vodafone FWA)
and Vodafone DE\T-Mobile PL (called GigaCube).
Modem is a MiniPCIe-to-USB based on Snapdragon X24,
it supports 4CA aggregation.
There are currently two hardware revisions, which
differ on the 5Ghz radio:
AT1 = QCA9984 5Ghz Radio on PCI-E bus
AT2 = IPQ4019 5Ghz Radio inside IPQ4019 like 2.4Ghz
Device specification
--------------------
SoC Type: Qualcomm IPQ4019
RAM: 256 MiB
Flash: 128 MiB SPI NAND (Winbond W25N01GV)
ROM: 2MiB SPI Flash (GD25Q16)
Wireless 2.4 GHz (IP4019): b/g/n, 2x2
Wireless 5 GHz:
(QCA9984): a/n/ac, 4x4 HW REV AT1
(IPA4019): a/n/ac, 2x2 HW REV AT2
Ethernet: 2xGbE (WAN/LAN1, LAN2)
USB ports: No
Button: 2 (Reset/WPS)
LEDs: 3 external leds: Network (white or red), Wifi, Power and 1 internal (blue)
Power: 12 VDC, 1 A
Connector type: Barrel
Bootloader: U-Boot
Installation
------------
1. Place OpenWrt initramfs image for the device on a TFTP
in the server's root. This example uses Server IP: 192.168.0.2
2. Connect serial console (115200,8n1) to serial connector
GND (which is right next to the thing with MF289F MIMO-V1.0), RX, TX
(refer to this image: https://ibb.co/31Gngpr).
3. Connect TFTP server to RJ-45 port (WAN/LAN1).
4. Stop in u-Boot (using ESC button) and run u-Boot commands:
setenv serverip 192.168.0.2
setenv ipaddr 192.168.0.1
set fdt_high 0x85000000
tftp openwrt-ipq40xx-generic-zte_mf289f-initramfs-fit-zImage.itb
bootm $loadaddr
5. Please make backup of original partitions, if you think about revert to
stock, specially mtd16 (Web UI) and mtd17 (rootFS).
Use /tmp as temporary storage and do:
WEB PARITION
--------------------------------------
cat /dev/mtd16 > /tmp/mtd16.bin
scp /tmp/mtd16.bin root@YOURSERVERIP:/
rm /tmp/mtd16.bin
ROOT PARITION
--------------------------------------
cat /dev/mtd17 > /tmp/mtd17.bin
scp /tmp/mtd17.bin root@YOURSERVERIP:/
rm /tmp/mtd17.bin
6. Login via ssh or serial and remove stock partitions
(default IP 192.168.0.1):
# this can return an error, if ubi was attached before
# or rootfs part was erased before.
ubiattach -m 17
# it could return error if rootfs part was erased before
ubirmvol /dev/ubi0 -N ubi_rootfs
# some devices doesn't have it
ubirmvol /dev/ubi0 -N ubi_rootfs_data
7. download and install image via sysupgrade -n
(either use wget/scp to copy the mf289f's squashfs-sysupgrade.bin
to the device's /tmp directory)
sysupgrade -n /tmp/openwrt-...-zte_mf289f-squashfs-sysupgrade.bin
Sometimes it could print ubi attach error, but please ignore it
if process goes forward.
Flash Layout
NAND:
mtd8: 000a0000 00020000 "fota-flag"
mtd9: 00080000 00020000 "0:ART"
mtd10: 00080000 00020000 "mac"
mtd11: 000c0000 00020000 "reserved2"
mtd12: 00400000 00020000 "cfg-param"
mtd13: 00400000 00020000 "log"
mtd14: 000a0000 00020000 "oops"
mtd15: 00500000 00020000 "reserved3"
mtd16: 00800000 00020000 "web"
mtd17: 01d00000 00020000 "rootfs"
mtd18: 01900000 00020000 "data"
mtd19: 03200000 00020000 "fota"
mtd20: 0041e000 0001f000 "kernel"
mtd21: 0101b000 0001f000 "ubi_rootfs"
SPI:
mtd0: 00040000 00010000 "0:SBL1"
mtd1: 00020000 00010000 "0:MIBIB"
mtd2: 00060000 00010000 "0:QSEE"
mtd3: 00010000 00010000 "0:CDT"
mtd4: 00010000 00010000 "0:DDRPARAMS"
mtd5: 00010000 00010000 "0:APPSBLENV"
mtd6: 000c0000 00010000 "0:APPSBL"
mtd7: 00050000 00010000 "0:reserved1"
Back to Stock (!!! need original dump taken from initramfs !!!)
-------------
1. Place mtd16.bin and mtd17.bin initramfs image
for the device on a TFTP in the server's root.
This example uses Server IP: 192.168.0.2
2. Connect serial console (115200,8n1) to serial console
connector (refer to the pin-out from above).
3. Connect TFTP server to RJ-45 port (WAN/LAN1).
4. rename mtd16.bin to web.img and mtd17.bin to root_uImage_s
5. Stop in u-Boot (using ESC button) and run u-Boot commands:
This will erase RootFS+Web:
nand erase 0x1000000 0x800000
nand erase 0x1800000 0x1D00000
This will restore RootFS:
tftpboot 0x84000000 ${dir}root_uImage_s
nand erase 0x1800000 0x1D00000
nand write $fileaddr 0x1800000 $filesize
This will restore Web Interface:
tftpboot 0x84000000 ${dir}web.img
nand erase 0x1000000 0x800000
nand write $fileaddr 0x1000000 $filesize
After first boot on stock firwmare, do a factory reset.
Push reset button for 5 seconds so all parameters will
be reverted to the one printed on label on bottom of the router
Signed-off-by: Giammarco Marzano <stich86@gmail.com>
Reviewed-by: Lech Perczak <lech.perczak@gmail.com>
(Warning: commit message did not conform to UTF-8 - hopefully fixed?,
added description of the pin-out if image goes down, reformatted
commit message to be hopefully somewhat readable on git-web,
redid some of the gpio-buttons & leds DT nodes, etc.)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-09-14 12:20:43 +00:00
|
|
|
define Device/zte_mf289f
|
|
|
|
|
$(call Device/zte_mf28x_common)
|
|
|
|
|
DEVICE_MODEL := MF289F
|
2023-05-17 20:02:40 +00:00
|
|
|
DEVICE_PACKAGES += ath10k-firmware-qca9984-ct
|
ipq40xx: Add ZTE MF289F
It's a 4G Cat.20 router used by Vodafone Italy (called Vodafone FWA)
and Vodafone DE\T-Mobile PL (called GigaCube).
Modem is a MiniPCIe-to-USB based on Snapdragon X24,
it supports 4CA aggregation.
There are currently two hardware revisions, which
differ on the 5Ghz radio:
AT1 = QCA9984 5Ghz Radio on PCI-E bus
AT2 = IPQ4019 5Ghz Radio inside IPQ4019 like 2.4Ghz
Device specification
--------------------
SoC Type: Qualcomm IPQ4019
RAM: 256 MiB
Flash: 128 MiB SPI NAND (Winbond W25N01GV)
ROM: 2MiB SPI Flash (GD25Q16)
Wireless 2.4 GHz (IP4019): b/g/n, 2x2
Wireless 5 GHz:
(QCA9984): a/n/ac, 4x4 HW REV AT1
(IPA4019): a/n/ac, 2x2 HW REV AT2
Ethernet: 2xGbE (WAN/LAN1, LAN2)
USB ports: No
Button: 2 (Reset/WPS)
LEDs: 3 external leds: Network (white or red), Wifi, Power and 1 internal (blue)
Power: 12 VDC, 1 A
Connector type: Barrel
Bootloader: U-Boot
Installation
------------
1. Place OpenWrt initramfs image for the device on a TFTP
in the server's root. This example uses Server IP: 192.168.0.2
2. Connect serial console (115200,8n1) to serial connector
GND (which is right next to the thing with MF289F MIMO-V1.0), RX, TX
(refer to this image: https://ibb.co/31Gngpr).
3. Connect TFTP server to RJ-45 port (WAN/LAN1).
4. Stop in u-Boot (using ESC button) and run u-Boot commands:
setenv serverip 192.168.0.2
setenv ipaddr 192.168.0.1
set fdt_high 0x85000000
tftp openwrt-ipq40xx-generic-zte_mf289f-initramfs-fit-zImage.itb
bootm $loadaddr
5. Please make backup of original partitions, if you think about revert to
stock, specially mtd16 (Web UI) and mtd17 (rootFS).
Use /tmp as temporary storage and do:
WEB PARITION
--------------------------------------
cat /dev/mtd16 > /tmp/mtd16.bin
scp /tmp/mtd16.bin root@YOURSERVERIP:/
rm /tmp/mtd16.bin
ROOT PARITION
--------------------------------------
cat /dev/mtd17 > /tmp/mtd17.bin
scp /tmp/mtd17.bin root@YOURSERVERIP:/
rm /tmp/mtd17.bin
6. Login via ssh or serial and remove stock partitions
(default IP 192.168.0.1):
# this can return an error, if ubi was attached before
# or rootfs part was erased before.
ubiattach -m 17
# it could return error if rootfs part was erased before
ubirmvol /dev/ubi0 -N ubi_rootfs
# some devices doesn't have it
ubirmvol /dev/ubi0 -N ubi_rootfs_data
7. download and install image via sysupgrade -n
(either use wget/scp to copy the mf289f's squashfs-sysupgrade.bin
to the device's /tmp directory)
sysupgrade -n /tmp/openwrt-...-zte_mf289f-squashfs-sysupgrade.bin
Sometimes it could print ubi attach error, but please ignore it
if process goes forward.
Flash Layout
NAND:
mtd8: 000a0000 00020000 "fota-flag"
mtd9: 00080000 00020000 "0:ART"
mtd10: 00080000 00020000 "mac"
mtd11: 000c0000 00020000 "reserved2"
mtd12: 00400000 00020000 "cfg-param"
mtd13: 00400000 00020000 "log"
mtd14: 000a0000 00020000 "oops"
mtd15: 00500000 00020000 "reserved3"
mtd16: 00800000 00020000 "web"
mtd17: 01d00000 00020000 "rootfs"
mtd18: 01900000 00020000 "data"
mtd19: 03200000 00020000 "fota"
mtd20: 0041e000 0001f000 "kernel"
mtd21: 0101b000 0001f000 "ubi_rootfs"
SPI:
mtd0: 00040000 00010000 "0:SBL1"
mtd1: 00020000 00010000 "0:MIBIB"
mtd2: 00060000 00010000 "0:QSEE"
mtd3: 00010000 00010000 "0:CDT"
mtd4: 00010000 00010000 "0:DDRPARAMS"
mtd5: 00010000 00010000 "0:APPSBLENV"
mtd6: 000c0000 00010000 "0:APPSBL"
mtd7: 00050000 00010000 "0:reserved1"
Back to Stock (!!! need original dump taken from initramfs !!!)
-------------
1. Place mtd16.bin and mtd17.bin initramfs image
for the device on a TFTP in the server's root.
This example uses Server IP: 192.168.0.2
2. Connect serial console (115200,8n1) to serial console
connector (refer to the pin-out from above).
3. Connect TFTP server to RJ-45 port (WAN/LAN1).
4. rename mtd16.bin to web.img and mtd17.bin to root_uImage_s
5. Stop in u-Boot (using ESC button) and run u-Boot commands:
This will erase RootFS+Web:
nand erase 0x1000000 0x800000
nand erase 0x1800000 0x1D00000
This will restore RootFS:
tftpboot 0x84000000 ${dir}root_uImage_s
nand erase 0x1800000 0x1D00000
nand write $fileaddr 0x1800000 $filesize
This will restore Web Interface:
tftpboot 0x84000000 ${dir}web.img
nand erase 0x1000000 0x800000
nand write $fileaddr 0x1000000 $filesize
After first boot on stock firwmare, do a factory reset.
Push reset button for 5 seconds so all parameters will
be reverted to the one printed on label on bottom of the router
Signed-off-by: Giammarco Marzano <stich86@gmail.com>
Reviewed-by: Lech Perczak <lech.perczak@gmail.com>
(Warning: commit message did not conform to UTF-8 - hopefully fixed?,
added description of the pin-out if image goes down, reformatted
commit message to be hopefully somewhat readable on git-web,
redid some of the gpio-buttons & leds DT nodes, etc.)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-09-14 12:20:43 +00:00
|
|
|
endef
|
2022-10-06 16:25:12 +00:00
|
|
|
TARGET_DEVICES += zte_mf289f
|
ipq40xx: Add ZTE MF289F
It's a 4G Cat.20 router used by Vodafone Italy (called Vodafone FWA)
and Vodafone DE\T-Mobile PL (called GigaCube).
Modem is a MiniPCIe-to-USB based on Snapdragon X24,
it supports 4CA aggregation.
There are currently two hardware revisions, which
differ on the 5Ghz radio:
AT1 = QCA9984 5Ghz Radio on PCI-E bus
AT2 = IPQ4019 5Ghz Radio inside IPQ4019 like 2.4Ghz
Device specification
--------------------
SoC Type: Qualcomm IPQ4019
RAM: 256 MiB
Flash: 128 MiB SPI NAND (Winbond W25N01GV)
ROM: 2MiB SPI Flash (GD25Q16)
Wireless 2.4 GHz (IP4019): b/g/n, 2x2
Wireless 5 GHz:
(QCA9984): a/n/ac, 4x4 HW REV AT1
(IPA4019): a/n/ac, 2x2 HW REV AT2
Ethernet: 2xGbE (WAN/LAN1, LAN2)
USB ports: No
Button: 2 (Reset/WPS)
LEDs: 3 external leds: Network (white or red), Wifi, Power and 1 internal (blue)
Power: 12 VDC, 1 A
Connector type: Barrel
Bootloader: U-Boot
Installation
------------
1. Place OpenWrt initramfs image for the device on a TFTP
in the server's root. This example uses Server IP: 192.168.0.2
2. Connect serial console (115200,8n1) to serial connector
GND (which is right next to the thing with MF289F MIMO-V1.0), RX, TX
(refer to this image: https://ibb.co/31Gngpr).
3. Connect TFTP server to RJ-45 port (WAN/LAN1).
4. Stop in u-Boot (using ESC button) and run u-Boot commands:
setenv serverip 192.168.0.2
setenv ipaddr 192.168.0.1
set fdt_high 0x85000000
tftp openwrt-ipq40xx-generic-zte_mf289f-initramfs-fit-zImage.itb
bootm $loadaddr
5. Please make backup of original partitions, if you think about revert to
stock, specially mtd16 (Web UI) and mtd17 (rootFS).
Use /tmp as temporary storage and do:
WEB PARITION
--------------------------------------
cat /dev/mtd16 > /tmp/mtd16.bin
scp /tmp/mtd16.bin root@YOURSERVERIP:/
rm /tmp/mtd16.bin
ROOT PARITION
--------------------------------------
cat /dev/mtd17 > /tmp/mtd17.bin
scp /tmp/mtd17.bin root@YOURSERVERIP:/
rm /tmp/mtd17.bin
6. Login via ssh or serial and remove stock partitions
(default IP 192.168.0.1):
# this can return an error, if ubi was attached before
# or rootfs part was erased before.
ubiattach -m 17
# it could return error if rootfs part was erased before
ubirmvol /dev/ubi0 -N ubi_rootfs
# some devices doesn't have it
ubirmvol /dev/ubi0 -N ubi_rootfs_data
7. download and install image via sysupgrade -n
(either use wget/scp to copy the mf289f's squashfs-sysupgrade.bin
to the device's /tmp directory)
sysupgrade -n /tmp/openwrt-...-zte_mf289f-squashfs-sysupgrade.bin
Sometimes it could print ubi attach error, but please ignore it
if process goes forward.
Flash Layout
NAND:
mtd8: 000a0000 00020000 "fota-flag"
mtd9: 00080000 00020000 "0:ART"
mtd10: 00080000 00020000 "mac"
mtd11: 000c0000 00020000 "reserved2"
mtd12: 00400000 00020000 "cfg-param"
mtd13: 00400000 00020000 "log"
mtd14: 000a0000 00020000 "oops"
mtd15: 00500000 00020000 "reserved3"
mtd16: 00800000 00020000 "web"
mtd17: 01d00000 00020000 "rootfs"
mtd18: 01900000 00020000 "data"
mtd19: 03200000 00020000 "fota"
mtd20: 0041e000 0001f000 "kernel"
mtd21: 0101b000 0001f000 "ubi_rootfs"
SPI:
mtd0: 00040000 00010000 "0:SBL1"
mtd1: 00020000 00010000 "0:MIBIB"
mtd2: 00060000 00010000 "0:QSEE"
mtd3: 00010000 00010000 "0:CDT"
mtd4: 00010000 00010000 "0:DDRPARAMS"
mtd5: 00010000 00010000 "0:APPSBLENV"
mtd6: 000c0000 00010000 "0:APPSBL"
mtd7: 00050000 00010000 "0:reserved1"
Back to Stock (!!! need original dump taken from initramfs !!!)
-------------
1. Place mtd16.bin and mtd17.bin initramfs image
for the device on a TFTP in the server's root.
This example uses Server IP: 192.168.0.2
2. Connect serial console (115200,8n1) to serial console
connector (refer to the pin-out from above).
3. Connect TFTP server to RJ-45 port (WAN/LAN1).
4. rename mtd16.bin to web.img and mtd17.bin to root_uImage_s
5. Stop in u-Boot (using ESC button) and run u-Boot commands:
This will erase RootFS+Web:
nand erase 0x1000000 0x800000
nand erase 0x1800000 0x1D00000
This will restore RootFS:
tftpboot 0x84000000 ${dir}root_uImage_s
nand erase 0x1800000 0x1D00000
nand write $fileaddr 0x1800000 $filesize
This will restore Web Interface:
tftpboot 0x84000000 ${dir}web.img
nand erase 0x1000000 0x800000
nand write $fileaddr 0x1000000 $filesize
After first boot on stock firwmare, do a factory reset.
Push reset button for 5 seconds so all parameters will
be reverted to the one printed on label on bottom of the router
Signed-off-by: Giammarco Marzano <stich86@gmail.com>
Reviewed-by: Lech Perczak <lech.perczak@gmail.com>
(Warning: commit message did not conform to UTF-8 - hopefully fixed?,
added description of the pin-out if image goes down, reformatted
commit message to be hopefully somewhat readable on git-web,
redid some of the gpio-buttons & leds DT nodes, etc.)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-09-14 12:20:43 +00:00
|
|
|
|
2021-01-17 05:54:04 +00:00
|
|
|
define Device/zyxel_nbg6617
|
|
|
|
|
$(call Device/FitImageLzma)
|
|
|
|
|
DEVICE_VENDOR := ZyXEL
|
|
|
|
|
DEVICE_MODEL := NBG6617
|
|
|
|
|
SOC := qcom-ipq4018
|
|
|
|
|
KERNEL_SIZE := 4096k
|
|
|
|
|
ROOTFS_SIZE := 24960k
|
|
|
|
|
RAS_BOARD := NBG6617
|
|
|
|
|
RAS_ROOTFS_SIZE := 19840k
|
|
|
|
|
RAS_VERSION := "$(VERSION_DIST) $(REVISION)"
|
|
|
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
|
|
|
|
IMAGES += factory.bin
|
|
|
|
|
# The ZyXEL firmware allows flashing thru the web-gui only when the rootfs is
|
|
|
|
|
# at least as large as the one of the initial firmware image (not the current
|
|
|
|
|
# one on the device). This only applies to the Web-UI, the bootlaoder ignores
|
|
|
|
|
# this minimum-size. However, the larger image can be flashed both ways.
|
|
|
|
|
IMAGE/factory.bin := append-rootfs | pad-rootfs | pad-to 64k | check-size $$$$(ROOTFS_SIZE) | zyxel-ras-image separate-kernel
|
|
|
|
|
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | check-size $$$$(ROOTFS_SIZE) | sysupgrade-tar rootfs=$$$$@ | append-metadata
|
2021-05-25 13:26:06 +00:00
|
|
|
DEVICE_PACKAGES := kmod-usb-ledtrig-usbport
|
2021-01-17 05:54:04 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += zyxel_nbg6617
|
|
|
|
|
|
|
|
|
|
define Device/zyxel_wre6606
|
|
|
|
|
$(call Device/FitImage)
|
|
|
|
|
DEVICE_VENDOR := ZyXEL
|
|
|
|
|
DEVICE_MODEL := WRE6606
|
|
|
|
|
DEVICE_DTS_CONFIG := config@4
|
|
|
|
|
SOC := qcom-ipq4018
|
|
|
|
|
IMAGE_SIZE := 13184k
|
2021-06-20 16:54:36 +00:00
|
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | check-size | append-metadata
|
2021-01-17 05:54:04 +00:00
|
|
|
DEVICE_PACKAGES := -kmod-ath10k-ct kmod-ath10k-ct-smallbuffers
|
|
|
|
|
endef
|
2022-09-28 15:42:48 +00:00
|
|
|
# Missing DSA Setup
|
|
|
|
|
#TARGET_DEVICES += zyxel_wre6606
|
