ath79: add support for Buffalo WZR-HP-AG300H
Buffalo WZR-HP-AG300H is a dual band router based on
Qualcom Atheros AR7161 rev 2
Specification:
- 680 MHz CPU (Qualcomm Atheros AR7161)
- 128 MiB RAM (2x Samsung K4H511638G-LCCC)
- 32 MiB Flash (2x Winbond 25Q128BVFG)
- WiFi 5 GHz a/n (Atheros AR9220)
- WiFi 2.4 GHz b/g/n (Atheros AR9223)
- 1000Base-T WAN (Atheros AR7161)
- 4x 1000Base-T Switch (Atheros AR8316)
- 1x USB 2.0
- 3 Buttons (AOSS/WPS, Reset, USB Eject)
- 2 Slide switches (Router (on/off/auto), Movie Engine (on/off))
- 9 LEDs (Power green, WLAN 2GHz green, WLAN 2GHz amber,
WLAN 5GHz green, WLAN 5GHz LED amber, Router green,
Diag red, Movie Engine blue, USB green)
It is already supported by the ar71xx target.
For more information on the device visit the wiki:
<https://openwrt.org/toh/buffalo/wzr-hp-ag300h>
Serial console:
- The UART Header is next to Movie Engine Switch.
- Pinout is RX - TX - GND - 3.3V (Square Pad is 3.3V)
- The Serial setting is 115200-8-N-1.
Installation of OpenWRT from vendor firmware:
- Connect to the Web-interface at http://192.168.11.1
- Go to “Administration” → “Firmware Upgrade”
- Upload the OpenWrt factory image
Tested:
- Ethernet (LAN, WAN)
- WiFi
- Installation
- via TFTP rescue
- via factory image
- on firmware v1.77 (28-05-2012)
- on pro firmware v24SP2 r30356 (26-03-2018)
- via sysupgrade from ar71xx
(wlan devices don't work because of new names)
- via sysupgrade from itself
- Buttons
- LEDS
- USB (Power control and device recognition)
Signed-off-by: Bernhard Frauendienst <openwrt@nospam.obeliks.de>
2018-08-18 16:28:02 +00:00
|
|
|
include ./common-buffalo.mk
|
2018-06-13 08:51:51 +00:00
|
|
|
include ./common-netgear.mk
|
2019-08-12 23:26:45 +00:00
|
|
|
include ./common-yuncore.mk
|
2018-03-02 18:28:50 +00:00
|
|
|
|
2018-09-04 21:27:02 +00:00
|
|
|
DEVICE_VARS += ADDPATTERN_ID ADDPATTERN_VERSION
|
2018-12-29 09:22:32 +00:00
|
|
|
DEVICE_VARS += SEAMA_SIGNATURE SEAMA_MTDBLOCK
|
2018-12-31 15:41:07 +00:00
|
|
|
DEVICE_VARS += KERNEL_INITRAMFS_PREFIX
|
2018-09-04 21:27:02 +00:00
|
|
|
|
|
|
|
|
define Build/cybertan-trx
|
|
|
|
|
@echo -n '' > $@-empty.bin
|
|
|
|
|
-$(STAGING_DIR_HOST)/bin/trx -o $@.new \
|
|
|
|
|
-f $(IMAGE_KERNEL) -F $@-empty.bin \
|
|
|
|
|
-x 32 -a 0x10000 -x -32 -f $@
|
|
|
|
|
-mv "$@.new" "$@"
|
|
|
|
|
-rm $@-empty.bin
|
|
|
|
|
endef
|
|
|
|
|
|
|
|
|
|
define Build/addpattern
|
|
|
|
|
-$(STAGING_DIR_HOST)/bin/addpattern -B $(ADDPATTERN_ID) \
|
|
|
|
|
-v v$(ADDPATTERN_VERSION) -i $@ -o $@.new
|
|
|
|
|
-mv "$@.new" "$@"
|
|
|
|
|
endef
|
|
|
|
|
|
2018-12-31 15:41:07 +00:00
|
|
|
define Build/add-elecom-factory-initramfs
|
|
|
|
|
$(eval edimax_model=$(word 1,$(1)))
|
|
|
|
|
$(eval product=$(word 2,$(1)))
|
2018-09-10 07:30:28 +00:00
|
|
|
|
2018-12-31 15:41:07 +00:00
|
|
|
$(STAGING_DIR_HOST)/bin/mkedimaximg \
|
|
|
|
|
-b -s CSYS -m $(edimax_model) \
|
|
|
|
|
-f 0x70000 -S 0x01100000 \
|
|
|
|
|
-i $@ -o $@.factory
|
|
|
|
|
|
|
|
|
|
( \
|
|
|
|
|
echo -n -e "ELECOM\x00\x00$(product)" | dd bs=40 count=1 conv=sync; \
|
|
|
|
|
echo -n "0.00" | dd bs=16 count=1 conv=sync; \
|
|
|
|
|
dd if=$@.factory; \
|
|
|
|
|
) > $@.factory.new
|
|
|
|
|
|
|
|
|
|
if [ "$$(stat -c%s $@.factory.new)" -le $$(($(subst k,* 1024,$(subst m, * 1024k,$(IMAGE_SIZE))))) ]; then \
|
|
|
|
|
mv $@.factory.new $(BIN_DIR)/$(KERNEL_INITRAMFS_PREFIX)-factory.bin; \
|
|
|
|
|
else \
|
|
|
|
|
echo "WARNING: initramfs kernel image too big, cannot generate factory image" >&2; \
|
|
|
|
|
fi
|
2018-09-10 07:30:28 +00:00
|
|
|
endef
|
|
|
|
|
|
2019-03-16 04:27:32 +00:00
|
|
|
define Build/nec-enc
|
|
|
|
|
$(STAGING_DIR_HOST)/bin/nec-enc \
|
|
|
|
|
-i $@ -o $@.new -k $(1)
|
|
|
|
|
mv $@.new $@
|
|
|
|
|
endef
|
|
|
|
|
|
2018-12-08 06:18:17 +00:00
|
|
|
define Build/nec-fw
|
|
|
|
|
( stat -c%s $@ | tr -d "\n" | dd bs=16 count=1 conv=sync; ) >> $@
|
|
|
|
|
( \
|
|
|
|
|
echo -n -e "$(1)" | dd bs=16 count=1 conv=sync; \
|
|
|
|
|
echo -n "0.0.00" | dd bs=16 count=1 conv=sync; \
|
|
|
|
|
dd if=$@; \
|
|
|
|
|
) > $@.new
|
|
|
|
|
mv $@.new $@
|
|
|
|
|
endef
|
|
|
|
|
|
2018-12-29 09:22:32 +00:00
|
|
|
define Device/seama
|
|
|
|
|
KERNEL := kernel-bin | append-dtb | relocate-kernel | lzma
|
|
|
|
|
KERNEL_INITRAMFS := $$(KERNEL) | seama
|
|
|
|
|
IMAGES += factory.bin
|
|
|
|
|
SEAMA_MTDBLOCK := 1
|
|
|
|
|
|
|
|
|
|
# 64 bytes offset:
|
|
|
|
|
# - 28 bytes seama_header
|
|
|
|
|
# - 36 bytes of META data (4-bytes aligned)
|
|
|
|
|
IMAGE/default := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | append-rootfs
|
|
|
|
|
IMAGE/sysupgrade.bin := \
|
|
|
|
|
$$(IMAGE/default) | seama | pad-rootfs | append-metadata | check-size $$$$(IMAGE_SIZE)
|
|
|
|
|
IMAGE/factory.bin := \
|
|
|
|
|
$$(IMAGE/default) | pad-rootfs -x 64 | seama | seama-seal | check-size $$$$(IMAGE_SIZE)
|
|
|
|
|
SEAMA_SIGNATURE :=
|
|
|
|
|
endef
|
|
|
|
|
|
2019-04-11 16:31:23 +00:00
|
|
|
define Device/8dev_carambola2
|
|
|
|
|
ATH_SOC := ar9331
|
|
|
|
|
DEVICE_TITLE := 8devices Carambola2
|
|
|
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-chipidea2
|
|
|
|
|
IMAGE_SIZE := 16000k
|
|
|
|
|
SUPPORTED_DEVICES += carambola2
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += 8dev_carambola2
|
|
|
|
|
|
2019-05-05 17:56:03 +00:00
|
|
|
define Device/aruba_ap-105
|
|
|
|
|
ATH_SOC := ar7161
|
|
|
|
|
DEVICE_TITLE := Aruba AP-105
|
|
|
|
|
IMAGE_SIZE := 16000k
|
|
|
|
|
DEVICE_PACKAGES := kmod-i2c-core kmod-i2c-gpio kmod-tpm-i2c-atmel
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += aruba_ap-105
|
|
|
|
|
|
2018-03-02 18:28:50 +00:00
|
|
|
define Device/avm_fritz300e
|
|
|
|
|
ATH_SOC := ar7242
|
|
|
|
|
DEVICE_TITLE := AVM FRITZ!WLAN Repeater 300E
|
|
|
|
|
KERNEL := kernel-bin | append-dtb | lzma | eva-image
|
|
|
|
|
KERNEL_INITRAMFS := $$(KERNEL)
|
|
|
|
|
IMAGE_SIZE := 15232k
|
|
|
|
|
IMAGE/sysupgrade.bin := append-kernel | pad-to 64k | \
|
|
|
|
|
append-squashfs-fakeroot-be | pad-to 256 | \
|
|
|
|
|
append-rootfs | pad-rootfs | append-metadata | check-size $$$$(IMAGE_SIZE)
|
|
|
|
|
DEVICE_PACKAGES := fritz-tffs rssileds -swconfig
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += avm_fritz300e
|
|
|
|
|
|
ath79: add support for Fritz!Box 4020
This commit adds support for the AVM Fritz!Box 4020 WiFi-router.
SoC: Qualcomm Atheros QCA9561 (Dragonfly) 750MHz
RAM: Winbond W971GG6KB-25
FLASH: Macronix MX25L12835F
WiFi: QCA9561 b/g/n 3x3 450Mbit/s
USB: 1x USB 2.0
IN: WPS button, WiFi button
OUT: Power LED green, Internet LED green, WLAN LED green,
LAN LED green, INFO LED green, INFO LED red
UART: Header Next to Black metal shield
Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet (LAN + WAN)
- WiFi (correct MAC)
- Installation via EVA bootloader
- OpenWRT sysupgrade
- Buttons
- LEDs
The USB port doesn't work. Both Root Hubs are detected as having 0 Ports:
[ 3.670807] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 3.723267] usbcore: registered new interface driver usbfs
[ 3.729058] usbcore: registered new interface driver hub
[ 3.734616] usbcore: registered new device driver usb
[ 3.744181] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.758357] SCSI subsystem initialized
[ 3.766026] ehci-platform: EHCI generic platform driver
[ 3.771548] ehci-platform ehci-platform.0: EHCI Host Controller
[ 3.777708] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
[ 3.788169] ehci-platform ehci-platform.0: irq 48, io mem 0x1b000000
[ 3.816647] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 0.00
[ 3.824001] hub 1-0:1.0: USB hub found
[ 3.828219] hub 1-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 3.835825] ehci-platform ehci-platform.1: EHCI Host Controller
[ 3.842009] ehci-platform ehci-platform.1: new USB bus registered, assigned bus number 2
[ 3.852481] ehci-platform ehci-platform.1: irq 49, io mem 0x1b400000
[ 3.886631] ehci-platform ehci-platform.1: USB 2.0 started, EHCI 0.00
[ 3.894011] hub 2-0:1.0: USB hub found
[ 3.898190] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 3.908928] usbcore: registered new interface driver usb-storage
[ 3.915634] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
A few words about the shift-register:
AVM used a trick to control the shift-register for the LEDs with only 2
pins, SERCLK and MOSI. Q7S, normally used for daisy-chaining multiple
shift-registers, pulls the latch, moving the shift register-state to
the storage register. It also pulls down MR (normally pulled up) to
clear the storage register, so the latch gets released and will not be
pulled by the remaining bits in the shift-register. Shift register is
all-zero after this.
For that we need to make sure output 7 is set to high on driver probe.
We accomplish this by using gpio-hogging.
Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 169.254.157.1 (Might also be 192.168.178.1).
Firmware can be uploaded like following:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put openwrt-sysupgrade.bin mtd1
Note that this procedure might take up to two minutes. After transfer is
complete you need to powercycle the device to boot OpenWRT.
Signed-off-by: David Bauer <mail@david-bauer.net>
2018-08-18 16:30:46 +00:00
|
|
|
define Device/avm_fritz4020
|
|
|
|
|
ATH_SOC := qca9561
|
|
|
|
|
DEVICE_TITLE := AVM FRITZ!Box 4020
|
|
|
|
|
IMAGE_SIZE := 15232k
|
|
|
|
|
KERNEL := kernel-bin | append-dtb | lzma | eva-image
|
|
|
|
|
KERNEL_INITRAMFS := $$(KERNEL)
|
|
|
|
|
IMAGE/sysupgrade.bin := append-kernel | pad-to 64k | \
|
|
|
|
|
append-squashfs-fakeroot-be | pad-to 256 | \
|
|
|
|
|
append-rootfs | pad-rootfs | append-metadata | check-size $$$$(IMAGE_SIZE)
|
|
|
|
|
DEVICE_PACKAGES := fritz-tffs
|
2019-02-23 12:12:49 +00:00
|
|
|
SUPPORTED_DEVICES += fritz4020
|
ath79: add support for Fritz!Box 4020
This commit adds support for the AVM Fritz!Box 4020 WiFi-router.
SoC: Qualcomm Atheros QCA9561 (Dragonfly) 750MHz
RAM: Winbond W971GG6KB-25
FLASH: Macronix MX25L12835F
WiFi: QCA9561 b/g/n 3x3 450Mbit/s
USB: 1x USB 2.0
IN: WPS button, WiFi button
OUT: Power LED green, Internet LED green, WLAN LED green,
LAN LED green, INFO LED green, INFO LED red
UART: Header Next to Black metal shield
Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet (LAN + WAN)
- WiFi (correct MAC)
- Installation via EVA bootloader
- OpenWRT sysupgrade
- Buttons
- LEDs
The USB port doesn't work. Both Root Hubs are detected as having 0 Ports:
[ 3.670807] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 3.723267] usbcore: registered new interface driver usbfs
[ 3.729058] usbcore: registered new interface driver hub
[ 3.734616] usbcore: registered new device driver usb
[ 3.744181] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.758357] SCSI subsystem initialized
[ 3.766026] ehci-platform: EHCI generic platform driver
[ 3.771548] ehci-platform ehci-platform.0: EHCI Host Controller
[ 3.777708] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
[ 3.788169] ehci-platform ehci-platform.0: irq 48, io mem 0x1b000000
[ 3.816647] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 0.00
[ 3.824001] hub 1-0:1.0: USB hub found
[ 3.828219] hub 1-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 3.835825] ehci-platform ehci-platform.1: EHCI Host Controller
[ 3.842009] ehci-platform ehci-platform.1: new USB bus registered, assigned bus number 2
[ 3.852481] ehci-platform ehci-platform.1: irq 49, io mem 0x1b400000
[ 3.886631] ehci-platform ehci-platform.1: USB 2.0 started, EHCI 0.00
[ 3.894011] hub 2-0:1.0: USB hub found
[ 3.898190] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 3.908928] usbcore: registered new interface driver usb-storage
[ 3.915634] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
A few words about the shift-register:
AVM used a trick to control the shift-register for the LEDs with only 2
pins, SERCLK and MOSI. Q7S, normally used for daisy-chaining multiple
shift-registers, pulls the latch, moving the shift register-state to
the storage register. It also pulls down MR (normally pulled up) to
clear the storage register, so the latch gets released and will not be
pulled by the remaining bits in the shift-register. Shift register is
all-zero after this.
For that we need to make sure output 7 is set to high on driver probe.
We accomplish this by using gpio-hogging.
Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 169.254.157.1 (Might also be 192.168.178.1).
Firmware can be uploaded like following:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put openwrt-sysupgrade.bin mtd1
Note that this procedure might take up to two minutes. After transfer is
complete you need to powercycle the device to boot OpenWRT.
Signed-off-by: David Bauer <mail@david-bauer.net>
2018-08-18 16:30:46 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += avm_fritz4020
|
|
|
|
|
|
2018-09-11 11:50:35 +00:00
|
|
|
define Device/buffalo_bhr-4grv
|
|
|
|
|
ATH_SOC := ar7242
|
|
|
|
|
DEVICE_TITLE := Buffalo BHR-4GRV
|
|
|
|
|
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-ledtrig-usbport
|
|
|
|
|
IMAGE_SIZE := 32256k
|
|
|
|
|
IMAGES += factory.bin tftp.bin
|
|
|
|
|
IMAGE/default := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE)
|
2018-10-07 11:37:42 +00:00
|
|
|
IMAGE/factory.bin := $$(IMAGE/default) | buffalo-enc BHR-4GRV 1.99 | buffalo-tag BHR-4GRV 3
|
2018-09-11 11:50:35 +00:00
|
|
|
IMAGE/tftp.bin := $$(IMAGE/default) | buffalo-tftp-header
|
|
|
|
|
SUPPORTED_DEVICES += wzr-hp-g450h
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += buffalo_bhr-4grv
|
|
|
|
|
|
ath79: modify mtd partitions for Buffalo BHR-4GRV2
This commit modifies mtd partitions define for Buffalo BHR-4GRV2 and
move it to generic subtarget.
In Buffalo BHR-4GRV2, "kernel" partition is located behined "rootfs"
partition in the stock firmware. This causes the size of the kernel
to be limited by the fixed value.
0x50000 0xe80000 0xff0000
+-------------------------------+--------------+
| rootfs | kernel |
| (14528k) | (1472k) |
+-------------------------------+--------------+
After ar71xx was updated to Kernel 4.14, the kernel size of BHR-4GRV2
exceeded the limit, and it breaks builds on official buildbot.
Since this issue was also confirmed in ath79, I modified the mtd
partitions to get rid of that limitation.
0x50000 0xff0000
+----------------------------------------------+
| firmware |
| (16000k) |
+----------------------------------------------+
However, this commit breaks compatibility with ar71xx firmware, so I
dropped "SUPPORTED_DEVICES += bhr-4grv2".
This commit requires new flash instruction instead of the old one.
Flash instruction using initramfs image:
1. Connect the computer to the LAN port of BHR-4GRV2
2. Set the IP address of the computer to 192.168.12.10
3. Rename the OpenWrt initramfs image to
"bhr4grv2-uImage-initramfs-gzip.bin" and place it into the TFTP
directory
4. Start the tftp server on the computer
5. While holding down the "ECO" button, connect power cable to
BHR-4GRV2 and turn on it
6. Flashing (orange) diag LED and release the finger from the button,
BHR-4GRV2 downloads the intiramfs image from TFTP server and boot
with it
7. On the initramfs image, create "/etc/fw_env.config" file with
following contents
/dev/mtd1 0x0 0x10000 0x10000
8. Execute following commands to add environment variables for
u-boot
fw_setenv ipaddr 192.168.12.1
fw_setenv serverip 192.168.12.10
fw_setenv ethaddr 00:aa:bb:cc:dd:ee
fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
9. Perform sysupgrade with squashfs-sysupgrade image
10. Wait ~150 seconds to complete flashing
And this commit includes small fix; BHR-4GRV2 has QCA9557 as a SoC,
not QCA9558.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-11-06 13:37:43 +00:00
|
|
|
define Device/buffalo_bhr-4grv2
|
|
|
|
|
ATH_SOC := qca9557
|
|
|
|
|
DEVICE_TITLE := Buffalo BHR-4GRV2
|
|
|
|
|
IMAGE_SIZE := 16000k
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += buffalo_bhr-4grv2
|
|
|
|
|
|
ath79: add support for Buffalo WZR-HP-AG300H
Buffalo WZR-HP-AG300H is a dual band router based on
Qualcom Atheros AR7161 rev 2
Specification:
- 680 MHz CPU (Qualcomm Atheros AR7161)
- 128 MiB RAM (2x Samsung K4H511638G-LCCC)
- 32 MiB Flash (2x Winbond 25Q128BVFG)
- WiFi 5 GHz a/n (Atheros AR9220)
- WiFi 2.4 GHz b/g/n (Atheros AR9223)
- 1000Base-T WAN (Atheros AR7161)
- 4x 1000Base-T Switch (Atheros AR8316)
- 1x USB 2.0
- 3 Buttons (AOSS/WPS, Reset, USB Eject)
- 2 Slide switches (Router (on/off/auto), Movie Engine (on/off))
- 9 LEDs (Power green, WLAN 2GHz green, WLAN 2GHz amber,
WLAN 5GHz green, WLAN 5GHz LED amber, Router green,
Diag red, Movie Engine blue, USB green)
It is already supported by the ar71xx target.
For more information on the device visit the wiki:
<https://openwrt.org/toh/buffalo/wzr-hp-ag300h>
Serial console:
- The UART Header is next to Movie Engine Switch.
- Pinout is RX - TX - GND - 3.3V (Square Pad is 3.3V)
- The Serial setting is 115200-8-N-1.
Installation of OpenWRT from vendor firmware:
- Connect to the Web-interface at http://192.168.11.1
- Go to “Administration” → “Firmware Upgrade”
- Upload the OpenWrt factory image
Tested:
- Ethernet (LAN, WAN)
- WiFi
- Installation
- via TFTP rescue
- via factory image
- on firmware v1.77 (28-05-2012)
- on pro firmware v24SP2 r30356 (26-03-2018)
- via sysupgrade from ar71xx
(wlan devices don't work because of new names)
- via sysupgrade from itself
- Buttons
- LEDS
- USB (Power control and device recognition)
Signed-off-by: Bernhard Frauendienst <openwrt@nospam.obeliks.de>
2018-08-18 16:28:02 +00:00
|
|
|
define Device/buffalo_wzr-hp-ag300h
|
|
|
|
|
ATH_SOC := ar7161
|
|
|
|
|
DEVICE_TITLE := Buffalo WZR-HP-AG300H
|
|
|
|
|
IMAGE_SIZE := 32256k
|
|
|
|
|
IMAGES += factory.bin tftp.bin
|
|
|
|
|
IMAGE/default := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE)
|
2018-10-07 11:37:42 +00:00
|
|
|
IMAGE/factory.bin := $$(IMAGE/default) | buffalo-enc WZR-HP-AG300H 1.99 | buffalo-tag WZR-HP-AG300H 3
|
ath79: add support for Buffalo WZR-HP-AG300H
Buffalo WZR-HP-AG300H is a dual band router based on
Qualcom Atheros AR7161 rev 2
Specification:
- 680 MHz CPU (Qualcomm Atheros AR7161)
- 128 MiB RAM (2x Samsung K4H511638G-LCCC)
- 32 MiB Flash (2x Winbond 25Q128BVFG)
- WiFi 5 GHz a/n (Atheros AR9220)
- WiFi 2.4 GHz b/g/n (Atheros AR9223)
- 1000Base-T WAN (Atheros AR7161)
- 4x 1000Base-T Switch (Atheros AR8316)
- 1x USB 2.0
- 3 Buttons (AOSS/WPS, Reset, USB Eject)
- 2 Slide switches (Router (on/off/auto), Movie Engine (on/off))
- 9 LEDs (Power green, WLAN 2GHz green, WLAN 2GHz amber,
WLAN 5GHz green, WLAN 5GHz LED amber, Router green,
Diag red, Movie Engine blue, USB green)
It is already supported by the ar71xx target.
For more information on the device visit the wiki:
<https://openwrt.org/toh/buffalo/wzr-hp-ag300h>
Serial console:
- The UART Header is next to Movie Engine Switch.
- Pinout is RX - TX - GND - 3.3V (Square Pad is 3.3V)
- The Serial setting is 115200-8-N-1.
Installation of OpenWRT from vendor firmware:
- Connect to the Web-interface at http://192.168.11.1
- Go to “Administration” → “Firmware Upgrade”
- Upload the OpenWrt factory image
Tested:
- Ethernet (LAN, WAN)
- WiFi
- Installation
- via TFTP rescue
- via factory image
- on firmware v1.77 (28-05-2012)
- on pro firmware v24SP2 r30356 (26-03-2018)
- via sysupgrade from ar71xx
(wlan devices don't work because of new names)
- via sysupgrade from itself
- Buttons
- LEDS
- USB (Power control and device recognition)
Signed-off-by: Bernhard Frauendienst <openwrt@nospam.obeliks.de>
2018-08-18 16:28:02 +00:00
|
|
|
IMAGE/tftp.bin := $$(IMAGE/default) | buffalo-tftp-header
|
|
|
|
|
DEVICE_PACKAGES := kmod-usb-core kmod-usb-ohci kmod-usb2 kmod-usb-ledtrig-usbport kmod-leds-reset kmod-owl-loader
|
|
|
|
|
SUPPORTED_DEVICES += wzr-hp-ag300h
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += buffalo_wzr-hp-ag300h
|
|
|
|
|
|
2018-10-02 13:28:45 +00:00
|
|
|
define Device/buffalo_wzr-hp-g302h-a1a0
|
|
|
|
|
ATH_SOC := ar7242
|
|
|
|
|
DEVICE_TITLE := Buffalo WZR-HP-G302H A1A0
|
|
|
|
|
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-ledtrig-usbport
|
|
|
|
|
IMAGE_SIZE := 32128k
|
|
|
|
|
IMAGES += factory.bin tftp.bin
|
|
|
|
|
IMAGE/default := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE)
|
|
|
|
|
IMAGE/factory.bin := $$(IMAGE/default) | buffalo-enc WZR-HP-G302H 1.99 | buffalo-tag WZR-HP-G302H 4
|
|
|
|
|
IMAGE/tftp.bin := $$(IMAGE/default) | buffalo-tftp-header
|
|
|
|
|
SUPPORTED_DEVICES += wzr-hp-g300nh2
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += buffalo_wzr-hp-g302h-a1a0
|
|
|
|
|
|
2018-08-02 07:14:10 +00:00
|
|
|
define Device/buffalo_wzr-hp-g450h
|
|
|
|
|
ATH_SOC := ar7242
|
2018-09-11 11:13:17 +00:00
|
|
|
DEVICE_TITLE := Buffalo WZR-HP-G450H/WZR-450HP
|
2018-08-02 07:14:10 +00:00
|
|
|
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-ledtrig-usbport
|
|
|
|
|
IMAGE_SIZE := 32256k
|
2018-09-11 11:13:17 +00:00
|
|
|
IMAGES += factory.bin tftp.bin
|
|
|
|
|
IMAGE/default := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE)
|
2018-10-07 11:37:42 +00:00
|
|
|
IMAGE/factory.bin := $$(IMAGE/default) | buffalo-enc WZR-HP-G450H 1.99 | buffalo-tag WZR-HP-G450H 3
|
2018-09-11 11:13:17 +00:00
|
|
|
IMAGE/tftp.bin := $$(IMAGE/default) | buffalo-tftp-header
|
2018-08-02 07:14:10 +00:00
|
|
|
SUPPORTED_DEVICES += wzr-hp-g450h
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += buffalo_wzr-hp-g450h
|
|
|
|
|
|
ath79: add support for COMFAST CF-E110N
This patch adds support for the COMFAST CF-E110N, an outdoor wireless
CPE with two Ethernet ports and a 802.11bgn radio.
Specifications:
- 650/400/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, both with PoE-in support
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, up to 26 dBm
- 11 dBi built-in antenna
- POWER/LAN/WAN/WLAN green LEDs
- 4x RSSI LEDs (2x red, 2x green)
- UART (115200 8N1) and GPIO (J9) headers on PCB
Flashing instructions:
The original firmware is based on OpenWrt so a sysupgrade image can be
installed via the stock web GUI. Settings from the original firmware
will be saved and restored on the new want, so a factory reset will be
needed: once the new firmware is flashed, perform the factory reset by
pushing the reset button several times during the boot process, while the
WAN LED flashes, until it starts flashing quicker.
The U-boot bootloader contains a recovery HTTP server to upload the
firmware. Push the reset button while powering the device on and keep it
pressed for >10 seconds. The recovery page will be at http://192.168.1.1
Notes:
The device is advertised, sold and labeled as "CF-E110N", but the
bootloader and the stock firmware identify it as "v2".
Acknowledgments:
Petr Štetiar <ynezz@true.cz>
Sebastian Kemper <sebastian_ml@gmx.net>
Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[drop unused labels from devicetree source file]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-10 14:44:56 +00:00
|
|
|
define Device/comfast_cf-e110n-v2
|
|
|
|
|
ATH_SOC := qca9533
|
|
|
|
|
DEVICE_TITLE := COMFAST CF-E110N v2
|
|
|
|
|
DEVICE_PACKAGES := rssileds kmod-leds-gpio -swconfig -uboot-envtools
|
|
|
|
|
IMAGE_SIZE := 16192k
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += comfast_cf-e110n-v2
|
|
|
|
|
|
ath79: add support for COMFAST CF-E120A v3
This patch adds support for the COMFAST CF-E120A v3, an outdoor wireless
CPE with two Ethernet ports and a 802.11an radio.
Specifications:
- AR9344 SoC
- 535/400/267 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, both with PoE-in support
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 5 GHz, up to 25 dBm
- 11 dBi built-in antenna
- POWER/LAN/WAN/WLAN green LEDs
- 4x RSSI LEDs (2x red, 2x green)
- UART (115200 8N1) and GPIO (J9) headers on PCB
Flashing instructions:
The original firmware is based on OpenWrt so a sysupgrade image can be
installed via the stock web GUI. Settings from the original firmware
will be saved and restored on the new one, so a factory reset will be
needed. To do so, once the new firmware is flashed, enter into failsafe
mode by pressing the reset button several times during the boot
process, while while the WAN LED flashes, until it starts flashing
faster. Once in failsafe mode, perform a factory reset as usual.
The U-boot bootloader contains a recovery HTTP server to upload the
firmware. Push the reset button while powering the device on and
keep it pressed for >10 seconds. The recovery page will be at
http://192.168.1.1
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2018-12-29 19:44:43 +00:00
|
|
|
define Device/comfast_cf-e120a-v3
|
|
|
|
|
ATH_SOC := ar9344
|
|
|
|
|
DEVICE_TITLE := COMFAST CF-E120A v3
|
|
|
|
|
DEVICE_PACKAGES := rssileds kmod-leds-gpio -uboot-envtools
|
|
|
|
|
IMAGE_SIZE := 8000k
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += comfast_cf-e120a-v3
|
|
|
|
|
|
2019-03-21 11:50:01 +00:00
|
|
|
define Device/comfast_cf-e5
|
|
|
|
|
ATH_SOC := qca9531
|
|
|
|
|
DEVICE_TITLE := COMFAST CF-E5/E7
|
|
|
|
|
DEVICE_PACKAGES := rssileds kmod-leds-gpio kmod-usb-core kmod-usb2 kmod-usb-net \
|
|
|
|
|
kmod-usb-net-qmi-wwan -swconfig -uboot-envtools
|
|
|
|
|
IMAGE_SIZE := 16192k
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += comfast_cf-e5
|
|
|
|
|
|
2018-12-27 01:32:38 +00:00
|
|
|
define Device/devolo_dvl1200e
|
|
|
|
|
ATH_SOC := qca9558
|
|
|
|
|
DEVICE_TITLE := devolo WiFi pro 1200e
|
|
|
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
|
|
|
IMAGE_SIZE := 15936k
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += devolo_dvl1200e
|
|
|
|
|
|
2019-01-01 18:17:23 +00:00
|
|
|
define Device/devolo_dvl1200i
|
|
|
|
|
ATH_SOC := qca9558
|
|
|
|
|
DEVICE_TITLE := devolo WiFi pro 1200i
|
|
|
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
|
|
|
IMAGE_SIZE := 15936k
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += devolo_dvl1200i
|
|
|
|
|
|
2018-12-27 01:32:39 +00:00
|
|
|
define Device/devolo_dvl1750c
|
|
|
|
|
ATH_SOC := qca9558
|
|
|
|
|
DEVICE_TITLE := devolo WiFi pro 1750c
|
|
|
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
|
|
|
IMAGE_SIZE := 15936k
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += devolo_dvl1750c
|
|
|
|
|
|
2019-01-20 16:46:42 +00:00
|
|
|
define Device/devolo_dvl1750e
|
|
|
|
|
ATH_SOC := qca9558
|
|
|
|
|
DEVICE_TITLE := devolo WiFi pro 1750e
|
|
|
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
|
|
|
IMAGE_SIZE := 15936k
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += devolo_dvl1750e
|
|
|
|
|
|
2019-01-01 18:17:22 +00:00
|
|
|
define Device/devolo_dvl1750i
|
|
|
|
|
ATH_SOC := qca9558
|
|
|
|
|
DEVICE_TITLE := devolo WiFi pro 1750i
|
|
|
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
|
|
|
IMAGE_SIZE := 15936k
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += devolo_dvl1750i
|
|
|
|
|
|
2019-06-11 15:27:51 +00:00
|
|
|
define Device/devolo_dvl1750x
|
|
|
|
|
ATH_SOC := qca9558
|
|
|
|
|
DEVICE_TITLE := devolo WiFi pro 1750x
|
|
|
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
|
|
|
IMAGE_SIZE := 15936k
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += devolo_dvl1750x
|
|
|
|
|
|
2018-08-09 17:49:29 +00:00
|
|
|
define Device/dlink_dir-825-b1
|
|
|
|
|
ATH_SOC := ar7161
|
|
|
|
|
DEVICE_TITLE := D-LINK DIR-825 B1
|
|
|
|
|
IMAGE_SIZE := 6208k
|
|
|
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata | check-size $$$$(IMAGE_SIZE)
|
|
|
|
|
DEVICE_PACKAGES := kmod-usb-core kmod-usb-ohci kmod-usb2 kmod-usb-ledtrig-usbport kmod-leds-reset kmod-owl-loader
|
|
|
|
|
SUPPORTED_DEVICES += dir-825-b1
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += dlink_dir-825-b1
|
|
|
|
|
|
2018-12-01 18:41:34 +00:00
|
|
|
define Device/dlink_dir-825-c1
|
|
|
|
|
ATH_SOC := ar9344
|
|
|
|
|
DEVICE_TITLE := D-LINK DIR-825 C1
|
|
|
|
|
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-ledtrig-usbport kmod-leds-reset kmod-owl-loader
|
|
|
|
|
SUPPORTED_DEVICES += dir-825-c1
|
|
|
|
|
IMAGE_SIZE := 15936k
|
|
|
|
|
IMAGES := factory.bin sysupgrade.bin
|
|
|
|
|
IMAGE/default := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs
|
2018-12-17 20:56:56 +00:00
|
|
|
IMAGE/factory.bin := $$(IMAGE/default) | pad-offset $$$$(IMAGE_SIZE) 26 | \
|
|
|
|
|
append-string 00DB120AR9344-RT-101214-00 | check-size $$$$(IMAGE_SIZE)
|
2018-12-01 18:41:34 +00:00
|
|
|
IMAGE/sysupgrade.bin := $$(IMAGE/default) | append-metadata | check-size $$$$(IMAGE_SIZE)
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += dlink_dir-825-c1
|
|
|
|
|
|
|
|
|
|
define Device/dlink_dir-835-a1
|
|
|
|
|
ATH_SOC := ar9344
|
|
|
|
|
DEVICE_TITLE := D-LINK DIR-835 A1
|
|
|
|
|
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-leds-reset kmod-owl-loader
|
|
|
|
|
SUPPORTED_DEVICES += dir-835-a1
|
|
|
|
|
IMAGE_SIZE := 15936k
|
|
|
|
|
IMAGES := factory.bin sysupgrade.bin
|
|
|
|
|
IMAGE/default := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs
|
2018-12-17 20:56:56 +00:00
|
|
|
IMAGE/factory.bin := $$(IMAGE/default) | pad-offset $$$$(IMAGE_SIZE) 26 | \
|
|
|
|
|
append-string 00DB120AR9344-RT-101214-00 | check-size $$$$(IMAGE_SIZE)
|
2018-12-01 18:41:34 +00:00
|
|
|
IMAGE/sysupgrade.bin := $$(IMAGE/default) | append-metadata | check-size $$$$(IMAGE_SIZE)
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += dlink_dir-835-a1
|
|
|
|
|
|
2018-12-29 09:22:32 +00:00
|
|
|
define Device/dlink_dir-859-a1
|
|
|
|
|
$(Device/seama)
|
|
|
|
|
ATH_SOC := qca9563
|
|
|
|
|
DEVICE_TITLE := D-LINK DIR-859 A1
|
|
|
|
|
IMAGE_SIZE := 15872k
|
2019-12-24 12:04:26 +00:00
|
|
|
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct
|
2018-12-29 09:22:32 +00:00
|
|
|
SEAMA_SIGNATURE := wrgac37_dlink.2013gui_dir859
|
|
|
|
|
SUPPORTED_DEVICES += dir-859-a1
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += dlink_dir-859-a1
|
|
|
|
|
|
2018-12-29 15:55:35 +00:00
|
|
|
define Device/elecom_wrc-1750ghbk2-i
|
|
|
|
|
ATH_SOC := qca9563
|
|
|
|
|
DEVICE_TITLE := ELECOM WRC-1750GHBK2-I/C
|
|
|
|
|
IMAGE_SIZE := 15808k
|
|
|
|
|
KERNEL_INITRAMFS := $$(KERNEL) | pad-to 2 | \
|
2018-12-31 15:41:07 +00:00
|
|
|
add-elecom-factory-initramfs RN68 WRC-1750GHBK2
|
2018-12-29 15:55:35 +00:00
|
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += elecom_wrc-1750ghbk2-i
|
|
|
|
|
|
2018-09-10 07:30:28 +00:00
|
|
|
define Device/elecom_wrc-300ghbk2-i
|
|
|
|
|
ATH_SOC := qca9563
|
|
|
|
|
DEVICE_TITLE := ELECOM WRC-300GHBK2-I
|
|
|
|
|
IMAGE_SIZE := 7616k
|
|
|
|
|
KERNEL_INITRAMFS := $$(KERNEL) | pad-to 2 | \
|
2018-12-31 15:41:07 +00:00
|
|
|
add-elecom-factory-initramfs RN51 WRC-300GHBK2-I
|
2018-09-10 07:30:28 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += elecom_wrc-300ghbk2-i
|
|
|
|
|
|
2018-05-08 05:22:38 +00:00
|
|
|
define Device/embeddedwireless_dorin
|
2018-05-06 08:20:11 +00:00
|
|
|
ATH_SOC := ar9331
|
|
|
|
|
DEVICE_TITLE := Embedded Wireless Dorin
|
|
|
|
|
DEVICE_PACKAGES := kmod-usb-chipidea2
|
2018-05-07 19:09:44 +00:00
|
|
|
IMAGE_SIZE := 16000k
|
2018-05-06 08:20:11 +00:00
|
|
|
endef
|
2018-05-08 05:22:38 +00:00
|
|
|
TARGET_DEVICES += embeddedwireless_dorin
|
2018-05-06 08:20:11 +00:00
|
|
|
|
2019-03-26 21:35:05 +00:00
|
|
|
define Device/engenius_ecb1750
|
|
|
|
|
ATH_SOC := qca9558
|
|
|
|
|
DEVICE_TITLE := EnGenius ECB1750
|
|
|
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
|
|
|
IMAGE_SIZE := 15680k
|
|
|
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
|
|
|
append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE) | \
|
|
|
|
|
senao-header -r 0x101 -p 0x6d -t 2
|
|
|
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata | check-size $$$$(IMAGE_SIZE)
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += engenius_ecb1750
|
|
|
|
|
|
ath79: add suport for EnGenius EPG5000
EnGenius EPG5000 (v1.0.0, marketed as IoT Gateway) is a dual band
wireless router.
Specification
SoC: Qualcomm Atheros QCA9558
RAM: 256 MB DDR2
Flash: 16 MB SPI NOR
WIFI: 2.4 GHz 3T3R integrated
5 GHz 3T3R QCA9880 Mini PCIe card
Ethernet: 5x 10/100/1000 Mbps QCA8337N
USB: 1x 2.0
LEDS: 4x GPIO controlled
Buttons: 2x GPIO controlled
UART: 4 pin header, starting count from white triangle on PCB
1. VCC 3.3V, 2. GND, 3. TX, 4. RX
baud: 115200, parity: none, flow control: none
Installation
1. Connect to one of LAN (yellow) ethernet ports,
2. Open router configuration interface,
3. Go to Tools > Firmware,
4. Select OpenWrt factory image with dlf extension and hit Apply,
5. Wait few minutes, after the Power LED will stop blinking, the router
is ready for configuration.
Alternative installation
1. Prepare TFTP server with OpenWrt sysupgrade image,
2. Connect to one of LAN (yellow) ethernet ports,
3. Connect to UART port (leaving out VCC pin!),
4. Power on router,
5. When asked to enter a number 1 or 3 hit 2, this will select flashing
image from TFTP server option,
6. You'll be prompted to enter TFTP server ip (default is 192.168.99.8),
then router ip (default is 192.168.99.9) and for last, image name
downloaded from TFTP server (default is uImageESR1200_1750),
7. After providing all information U-Boot will start flashing the image,
You can observe progress on console, it'll take few minutes and when
the Power LED will stop blinking, router is ready for configuration.
Additional information
If connected to UART, when prompted for number on boot, one can enter
number 4 to open bootloader (U-Boot) command line.
OEM firmware shell password is: aigo3d0a0tdagr
useful for creating backup of original firmware.
When doing upgrade from OpenWrt ar71xx image, it is recomended to not keep
the old configuration.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-03-04 14:18:53 +00:00
|
|
|
define Device/engenius_epg5000
|
|
|
|
|
ATH_SOC := qca9558
|
|
|
|
|
DEVICE_TITLE := EnGenius EPG5000
|
|
|
|
|
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct kmod-usb2
|
|
|
|
|
IMAGE_SIZE := 14656k
|
|
|
|
|
IMAGES += factory.dlf
|
|
|
|
|
IMAGE/factory.dlf := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
|
|
|
append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE) | \
|
|
|
|
|
senao-header -r 0x101 -p 0x71 -t 2
|
|
|
|
|
SUPPORTED_DEVICES += epg5000
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += engenius_epg5000
|
|
|
|
|
|
2018-12-18 08:35:30 +00:00
|
|
|
define Device/engenius_ews511ap
|
|
|
|
|
ATH_SOC := qca9531
|
|
|
|
|
DEVICE_TITLE := EnGenius EWS511AP
|
|
|
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9887-ct
|
|
|
|
|
IMAGE_SIZE := 16000k
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += engenius_ews511ap
|
|
|
|
|
|
2018-08-02 07:14:10 +00:00
|
|
|
define Device/etactica_eg200
|
2018-05-07 16:08:00 +00:00
|
|
|
ATH_SOC := ar9331
|
|
|
|
|
DEVICE_TITLE := eTactica EG200
|
|
|
|
|
DEVICE_PACKAGES := kmod-usb-chipidea2 kmod-ledtrig-oneshot \
|
|
|
|
|
kmod-usb-serial kmod-usb-serial-ftdi kmod-usb-storage kmod-fs-ext4
|
2018-08-02 07:14:10 +00:00
|
|
|
SUPPORTED_DEVICES += rme-eg200
|
2018-05-07 16:08:00 +00:00
|
|
|
endef
|
2018-08-02 07:14:10 +00:00
|
|
|
TARGET_DEVICES += etactica_eg200
|
2018-05-07 16:08:00 +00:00
|
|
|
|
2018-12-30 20:37:50 +00:00
|
|
|
define Device/glinet_gl-ar150
|
2018-05-06 08:20:11 +00:00
|
|
|
ATH_SOC := ar9330
|
|
|
|
|
DEVICE_TITLE := GL.iNet GL-AR150
|
|
|
|
|
DEVICE_PACKAGES := kmod-usb-chipidea2
|
|
|
|
|
IMAGE_SIZE := 16000k
|
2018-05-07 20:41:04 +00:00
|
|
|
SUPPORTED_DEVICES += gl-ar150
|
2018-05-06 08:20:11 +00:00
|
|
|
endef
|
2018-12-30 20:37:50 +00:00
|
|
|
TARGET_DEVICES += glinet_gl-ar150
|
2018-05-06 08:20:11 +00:00
|
|
|
|
2019-03-07 04:44:33 +00:00
|
|
|
define Device/glinet_gl-ar300m-common-nor
|
2018-10-29 03:56:46 +00:00
|
|
|
ATH_SOC := qca9531
|
2018-05-27 05:37:22 +00:00
|
|
|
DEVICE_PACKAGES := kmod-usb-core kmod-usb2
|
|
|
|
|
IMAGE_SIZE := 16000k
|
|
|
|
|
SUPPORTED_DEVICES += gl-ar300m
|
|
|
|
|
endef
|
2019-03-07 04:44:33 +00:00
|
|
|
|
|
|
|
|
define Device/glinet_gl-ar300m-lite
|
|
|
|
|
$(Device/glinet_gl-ar300m-common-nor)
|
|
|
|
|
DEVICE_TITLE := GL.iNet GL-AR300M-Lite
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += glinet_gl-ar300m-lite
|
|
|
|
|
|
|
|
|
|
define Device/glinet_gl-ar300m-nor
|
|
|
|
|
$(Device/glinet_gl-ar300m-common-nor)
|
|
|
|
|
DEVICE_TITLE := GL.iNet GL-AR300M
|
|
|
|
|
endef
|
2019-11-07 17:53:37 +00:00
|
|
|
#TARGET_DEVICES += glinet_gl-ar300m-nor
|
2018-05-27 05:37:22 +00:00
|
|
|
|
2019-01-01 12:03:20 +00:00
|
|
|
define Device/glinet_gl-ar750s
|
2018-12-30 16:36:22 +00:00
|
|
|
ATH_SOC := qca9563
|
|
|
|
|
DEVICE_TITLE := GL.iNet GL-AR750S
|
2019-05-16 14:24:43 +00:00
|
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca9887-ct block-mount
|
2018-12-30 16:36:22 +00:00
|
|
|
IMAGE_SIZE := 16000k
|
|
|
|
|
SUPPORTED_DEVICES += gl-ar750s
|
|
|
|
|
endef
|
2019-11-07 17:53:37 +00:00
|
|
|
#TARGET_DEVICES += glinet_gl-ar750s
|
2018-12-30 16:36:22 +00:00
|
|
|
|
2018-11-26 14:39:25 +00:00
|
|
|
define Device/glinet_gl-x750
|
2018-10-29 03:56:46 +00:00
|
|
|
ATH_SOC := qca9531
|
2018-11-26 14:39:25 +00:00
|
|
|
DEVICE_TITLE := GL.iNet GL-X750
|
2018-12-17 00:58:49 +00:00
|
|
|
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca9887-ct
|
2018-11-05 02:03:05 +00:00
|
|
|
IMAGE_SIZE := 16000k
|
|
|
|
|
endef
|
2018-11-26 14:39:25 +00:00
|
|
|
TARGET_DEVICES += glinet_gl-x750
|
2018-11-05 02:03:05 +00:00
|
|
|
|
2018-08-20 07:32:42 +00:00
|
|
|
define Device/iodata_etg3-r
|
|
|
|
|
ATH_SOC := ar9342
|
|
|
|
|
DEVICE_TITLE := I-O DATA ETG3-R
|
|
|
|
|
IMAGE_SIZE := 7680k
|
2019-04-13 03:21:02 +00:00
|
|
|
DEVICE_PACKAGES := -iwinfo -kmod-ath9k -wpad-basic
|
2018-08-20 07:32:42 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += iodata_etg3-r
|
|
|
|
|
|
2018-08-16 08:08:28 +00:00
|
|
|
define Device/iodata_wn-ac1167dgr
|
|
|
|
|
ATH_SOC := qca9557
|
|
|
|
|
DEVICE_TITLE := I-O DATA WN-AC1167DGR
|
|
|
|
|
IMAGE_SIZE := 14656k
|
|
|
|
|
IMAGES += factory.bin
|
|
|
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
|
|
|
append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE) | \
|
|
|
|
|
senao-header -r 0x30a -p 0x61 -t 2
|
2018-09-05 12:51:44 +00:00
|
|
|
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
2018-08-16 08:08:28 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += iodata_wn-ac1167dgr
|
|
|
|
|
|
2019-02-05 08:23:58 +00:00
|
|
|
define Device/iodata_wn-ac1600dgr
|
|
|
|
|
ATH_SOC := qca9557
|
|
|
|
|
DEVICE_TITLE := I-O DATA WN-AC1600DGR
|
|
|
|
|
IMAGE_SIZE := 14656k
|
|
|
|
|
IMAGES += factory.bin
|
|
|
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
|
|
|
append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE) | \
|
|
|
|
|
senao-header -r 0x30a -p 0x60 -t 2 -v 200
|
|
|
|
|
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += iodata_wn-ac1600dgr
|
|
|
|
|
|
2018-08-10 00:07:53 +00:00
|
|
|
define Device/iodata_wn-ac1600dgr2
|
|
|
|
|
ATH_SOC := qca9557
|
|
|
|
|
DEVICE_TITLE := I-O DATA WN-AC1600DGR2
|
|
|
|
|
IMAGE_SIZE := 14656k
|
|
|
|
|
IMAGES += factory.bin
|
|
|
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
|
|
|
append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE) | \
|
|
|
|
|
senao-header -r 0x30a -p 0x60 -t 2 -v 200
|
2018-09-05 12:51:44 +00:00
|
|
|
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
2018-08-10 00:07:53 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += iodata_wn-ac1600dgr2
|
|
|
|
|
|
2018-11-30 10:04:23 +00:00
|
|
|
define Device/iodata_wn-ag300dgr
|
|
|
|
|
ATH_SOC := ar1022
|
|
|
|
|
DEVICE_TITLE := I-O DATA WN-AG300DGR
|
|
|
|
|
IMAGE_SIZE := 15424k
|
|
|
|
|
IMAGES += factory.bin
|
|
|
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
|
|
|
append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE) | \
|
|
|
|
|
senao-header -r 0x30a -p 0x47 -t 2
|
|
|
|
|
DEVICE_PACKAGES := kmod-usb-core kmod-usb2
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += iodata_wn-ag300dgr
|
|
|
|
|
|
ath79: add support for jjPlus JA76PF2
jjPlus JA76PF2 (marketed as IntellusPro2) is a network embedded board.
Specification
SoC: Atheros AR7161
RAM: 64 MB DDR
Flash: 16 MB SPI NOR
Ethernet: 2x 10/100/1000 Mbps AR8316
LAN (CN11), WAN/PoE (CN6 - close to power barrel
connector, 48 V)
MiniPCI: 2x
LEDS: 4x, which 3 are GPIO controlled
Buttons: 2x GPIO controlled
Reset (SW1, closer to ethernet ports), WPS (SW2)
Serial: 1x (only RX and TX are wired)
baud: 115200, parity: none, flow control: none
Currently there is one caveat compared to ar71xx target images as the
MAC addresses are random on every reboot. To remedy this one needs to
store the WAN MAC address in RedBoot configuration. OpenWrt on first
boot, after flashing, will read out the address and assign proper ones
to both WAN and LAN ports. It is iportant to NOT keep the old
configuration when doing sysupgrade from ar71xx.
Upgrading from OpenWrt ar71xx image
1. Connect to serial port,
2. Download OpenWrt sysupgrade image to /tmp directory and flash it
with:
sysupgrade -n <openwrt_sysupgrade_image_name>
3. After writing new image OpenWrt will reboot, now interrupt boot
process and enter RedBoot (bootloader) command line by pressing
Ctrl+C,
4. Enter following commands (replace variable accordingly),
set_mac (to view MAC addresses)
alias ethaddr <wan_port_mac_adress>
(confirm storing the value by inputting y and pressing Enter)
reset
5. Now board should restart and boot OpenWrt with proper MAC addresses.
Installation
1. Prepare TFTP server with OpenWrt initramfs image,
2. Connect to WAN ethernet port,
3. Connect to serial port,
4. Power on the board and enter RedBoot (bootloader) command line by
pressing Ctrl+C,
5. Enter following commands (replace variables accordingly):
set_mac (to view MAC addresses)
alias ethaddr <wan_port_mac_address>
(confirm storing the value by inputting y and pressing Enter)
ip_adress -l <board_ip_adress>/24 -h <tftp_server_ip_adress>
load -r -b 0x80060000 <openwrt_initramfs_image_name>
exec -c ""
6. Now board should boot OpenWrt initramfs image,
7. Download OpenWrt sysupgrade image to /tmp directory and flash it
with:
sysupgrade <openwrt_sysupgrade_image_name>
8. Wait few minutes, after the D2 LED will stop blinking, the board
is ready for configuration.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-03-06 19:15:19 +00:00
|
|
|
define Device/jjplus_ja76pf2
|
|
|
|
|
ATH_SOC := ar7161
|
|
|
|
|
DEVICE_TITLE := jjPlus JA76PF2
|
|
|
|
|
DEVICE_PACKAGES += -kmod-ath9k -swconfig -wpad-mini -uboot-envtools fconfig
|
2019-08-23 13:50:49 +00:00
|
|
|
IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | combined-image | append-metadata | check-size $$$$(IMAGE_SIZE)
|
ath79: add support for jjPlus JA76PF2
jjPlus JA76PF2 (marketed as IntellusPro2) is a network embedded board.
Specification
SoC: Atheros AR7161
RAM: 64 MB DDR
Flash: 16 MB SPI NOR
Ethernet: 2x 10/100/1000 Mbps AR8316
LAN (CN11), WAN/PoE (CN6 - close to power barrel
connector, 48 V)
MiniPCI: 2x
LEDS: 4x, which 3 are GPIO controlled
Buttons: 2x GPIO controlled
Reset (SW1, closer to ethernet ports), WPS (SW2)
Serial: 1x (only RX and TX are wired)
baud: 115200, parity: none, flow control: none
Currently there is one caveat compared to ar71xx target images as the
MAC addresses are random on every reboot. To remedy this one needs to
store the WAN MAC address in RedBoot configuration. OpenWrt on first
boot, after flashing, will read out the address and assign proper ones
to both WAN and LAN ports. It is iportant to NOT keep the old
configuration when doing sysupgrade from ar71xx.
Upgrading from OpenWrt ar71xx image
1. Connect to serial port,
2. Download OpenWrt sysupgrade image to /tmp directory and flash it
with:
sysupgrade -n <openwrt_sysupgrade_image_name>
3. After writing new image OpenWrt will reboot, now interrupt boot
process and enter RedBoot (bootloader) command line by pressing
Ctrl+C,
4. Enter following commands (replace variable accordingly),
set_mac (to view MAC addresses)
alias ethaddr <wan_port_mac_adress>
(confirm storing the value by inputting y and pressing Enter)
reset
5. Now board should restart and boot OpenWrt with proper MAC addresses.
Installation
1. Prepare TFTP server with OpenWrt initramfs image,
2. Connect to WAN ethernet port,
3. Connect to serial port,
4. Power on the board and enter RedBoot (bootloader) command line by
pressing Ctrl+C,
5. Enter following commands (replace variables accordingly):
set_mac (to view MAC addresses)
alias ethaddr <wan_port_mac_address>
(confirm storing the value by inputting y and pressing Enter)
ip_adress -l <board_ip_adress>/24 -h <tftp_server_ip_adress>
load -r -b 0x80060000 <openwrt_initramfs_image_name>
exec -c ""
6. Now board should boot OpenWrt initramfs image,
7. Download OpenWrt sysupgrade image to /tmp directory and flash it
with:
sysupgrade <openwrt_sysupgrade_image_name>
8. Wait few minutes, after the D2 LED will stop blinking, the board
is ready for configuration.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-03-06 19:15:19 +00:00
|
|
|
# IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE) | sysupgrade-tar rootfs=$$$$@ | append-metadata
|
|
|
|
|
KERNEL := kernel-bin | append-dtb | lzma | pad-to $$(BLOCKSIZE)
|
|
|
|
|
KERNEL_INITRAMFS := kernel-bin | append-dtb
|
|
|
|
|
IMAGE_SIZE := 16000k
|
2019-08-23 13:50:50 +00:00
|
|
|
SUPPORTED_DEVICES += ja76pf2
|
ath79: add support for jjPlus JA76PF2
jjPlus JA76PF2 (marketed as IntellusPro2) is a network embedded board.
Specification
SoC: Atheros AR7161
RAM: 64 MB DDR
Flash: 16 MB SPI NOR
Ethernet: 2x 10/100/1000 Mbps AR8316
LAN (CN11), WAN/PoE (CN6 - close to power barrel
connector, 48 V)
MiniPCI: 2x
LEDS: 4x, which 3 are GPIO controlled
Buttons: 2x GPIO controlled
Reset (SW1, closer to ethernet ports), WPS (SW2)
Serial: 1x (only RX and TX are wired)
baud: 115200, parity: none, flow control: none
Currently there is one caveat compared to ar71xx target images as the
MAC addresses are random on every reboot. To remedy this one needs to
store the WAN MAC address in RedBoot configuration. OpenWrt on first
boot, after flashing, will read out the address and assign proper ones
to both WAN and LAN ports. It is iportant to NOT keep the old
configuration when doing sysupgrade from ar71xx.
Upgrading from OpenWrt ar71xx image
1. Connect to serial port,
2. Download OpenWrt sysupgrade image to /tmp directory and flash it
with:
sysupgrade -n <openwrt_sysupgrade_image_name>
3. After writing new image OpenWrt will reboot, now interrupt boot
process and enter RedBoot (bootloader) command line by pressing
Ctrl+C,
4. Enter following commands (replace variable accordingly),
set_mac (to view MAC addresses)
alias ethaddr <wan_port_mac_adress>
(confirm storing the value by inputting y and pressing Enter)
reset
5. Now board should restart and boot OpenWrt with proper MAC addresses.
Installation
1. Prepare TFTP server with OpenWrt initramfs image,
2. Connect to WAN ethernet port,
3. Connect to serial port,
4. Power on the board and enter RedBoot (bootloader) command line by
pressing Ctrl+C,
5. Enter following commands (replace variables accordingly):
set_mac (to view MAC addresses)
alias ethaddr <wan_port_mac_address>
(confirm storing the value by inputting y and pressing Enter)
ip_adress -l <board_ip_adress>/24 -h <tftp_server_ip_adress>
load -r -b 0x80060000 <openwrt_initramfs_image_name>
exec -c ""
6. Now board should boot OpenWrt initramfs image,
7. Download OpenWrt sysupgrade image to /tmp directory and flash it
with:
sysupgrade <openwrt_sysupgrade_image_name>
8. Wait few minutes, after the D2 LED will stop blinking, the board
is ready for configuration.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-03-06 19:15:19 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += jjplus_ja76pf2
|
|
|
|
|
|
2019-03-09 01:10:25 +00:00
|
|
|
define Device/librerouter_librerouter-v1
|
|
|
|
|
ATH_SOC := qca9558
|
|
|
|
|
DEVICE_TITLE := LibreRouter v1
|
|
|
|
|
IMAGE_SIZE := 7936k
|
|
|
|
|
DEVICE_PACKAGES := kmod-usb-core kmod-usb2
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += librerouter_librerouter-v1
|
|
|
|
|
|
2019-03-16 04:27:32 +00:00
|
|
|
define Device/nec_wg1200cr
|
|
|
|
|
ATH_SOC := qca9563
|
|
|
|
|
DEVICE_TITLE := NEC Aterm WG1200CR
|
|
|
|
|
IMAGE_SIZE := 7616k
|
|
|
|
|
SEAMA_MTDBLOCK := 6
|
|
|
|
|
SEAMA_SIGNATURE := wrgac72_necpf.2016gui_wg1200cr
|
|
|
|
|
IMAGES += factory.bin
|
|
|
|
|
IMAGE/default := \
|
|
|
|
|
append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | append-rootfs
|
|
|
|
|
IMAGE/sysupgrade.bin := \
|
|
|
|
|
$$(IMAGE/default) | seama | pad-rootfs | append-metadata | check-size $$$$(IMAGE_SIZE)
|
|
|
|
|
IMAGE/factory.bin := \
|
|
|
|
|
$$(IMAGE/default) | pad-rootfs -x 64 | seama | seama-seal | nec-enc 9gsiy9nzep452pad | \
|
|
|
|
|
check-size $$$$(IMAGE_SIZE)
|
|
|
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += nec_wg1200cr
|
|
|
|
|
|
2018-12-08 06:18:17 +00:00
|
|
|
define Device/nec_wg800hp
|
|
|
|
|
ATH_SOC := qca9563
|
|
|
|
|
DEVICE_TITLE := NEC Aterm WG800HP
|
|
|
|
|
IMAGE_SIZE := 7104k
|
|
|
|
|
IMAGES += factory.bin
|
|
|
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
|
|
|
append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE) | \
|
|
|
|
|
xor-image -p 6A57190601121E4C004C1E1201061957 -x | \
|
|
|
|
|
nec-fw LASER_ATERM
|
2019-12-24 12:04:26 +00:00
|
|
|
DEVICE_PACKAGES := kmod-ath10k-ct-smallbuffers ath10k-firmware-qca9887-ct-htt
|
2018-12-08 06:18:17 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += nec_wg800hp
|
|
|
|
|
|
2018-08-08 20:13:44 +00:00
|
|
|
define Device/ocedo_koala
|
|
|
|
|
ATH_SOC := qca9558
|
|
|
|
|
DEVICE_TITLE := OCEDO Koala
|
2018-09-05 12:51:44 +00:00
|
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
2018-08-08 20:13:44 +00:00
|
|
|
SUPPORTED_DEVICES += koala
|
|
|
|
|
IMAGE_SIZE := 7424k
|
|
|
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata | check-size $$$$(IMAGE_SIZE)
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += ocedo_koala
|
|
|
|
|
|
2018-07-06 16:23:31 +00:00
|
|
|
define Device/ocedo_raccoon
|
|
|
|
|
ATH_SOC := ar9344
|
|
|
|
|
DEVICE_TITLE := OCEDO Raccoon
|
|
|
|
|
IMAGE_SIZE := 7424k
|
|
|
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata | check-size $$$$(IMAGE_SIZE)
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += ocedo_raccoon
|
|
|
|
|
|
2019-03-21 15:43:27 +00:00
|
|
|
define Device/ocedo_ursus
|
|
|
|
|
ATH_SOC := qca9558
|
|
|
|
|
DEVICE_TITLE := OCEDO Ursus
|
|
|
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
|
|
|
IMAGE_SIZE := 7424k
|
|
|
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata | check-size $$$$(IMAGE_SIZE)
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += ocedo_ursus
|
|
|
|
|
|
2018-05-08 05:22:38 +00:00
|
|
|
define Device/openmesh_om5p-ac-v2
|
2018-05-06 08:20:11 +00:00
|
|
|
ATH_SOC := qca9558
|
2018-05-08 05:22:38 +00:00
|
|
|
DEVICE_TITLE := OpenMesh OM5P-AC v2
|
2018-09-05 12:51:44 +00:00
|
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct om-watchdog
|
2018-05-07 19:09:44 +00:00
|
|
|
IMAGE_SIZE := 7808k
|
2018-05-07 20:41:04 +00:00
|
|
|
SUPPORTED_DEVICES += om5p-acv2
|
2018-05-06 08:20:11 +00:00
|
|
|
endef
|
2018-05-08 05:22:38 +00:00
|
|
|
TARGET_DEVICES += openmesh_om5p-ac-v2
|
2018-05-06 08:20:11 +00:00
|
|
|
|
2018-07-28 12:52:39 +00:00
|
|
|
define Device/pcs_cap324
|
|
|
|
|
ATH_SOC := ar9344
|
|
|
|
|
DEVICE_TITLE := PowerCloud Systems CAP324
|
|
|
|
|
IMAGE_SIZE := 16000k
|
|
|
|
|
SUPPORTED_DEVICES += cap324
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += pcs_cap324
|
|
|
|
|
|
2018-07-28 12:57:22 +00:00
|
|
|
define Device/pcs_cr3000
|
|
|
|
|
ATH_SOC := ar9341
|
|
|
|
|
DEVICE_TITLE := PowerCloud Systems CR3000
|
|
|
|
|
IMAGE_SIZE := 7808k
|
|
|
|
|
SUPPORTED_DEVICES += cr3000
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += pcs_cr3000
|
|
|
|
|
|
2018-07-20 20:52:46 +00:00
|
|
|
define Device/pcs_cr5000
|
|
|
|
|
ATH_SOC := ar9344
|
|
|
|
|
DEVICE_TITLE := PowerCloud Systems CR5000
|
2018-08-16 07:53:26 +00:00
|
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-core
|
2018-07-20 20:52:46 +00:00
|
|
|
IMAGE_SIZE := 7808k
|
|
|
|
|
SUPPORTED_DEVICES += cr5000
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += pcs_cr5000
|
|
|
|
|
|
2018-08-11 11:47:21 +00:00
|
|
|
define Device/netgear_wndr3x00
|
2018-05-06 08:20:11 +00:00
|
|
|
ATH_SOC := ar7161
|
2018-05-07 19:09:44 +00:00
|
|
|
IMAGE/default := append-kernel | pad-to $$$$(BLOCKSIZE) | netgear-squashfs | append-rootfs | pad-rootfs
|
2018-08-13 20:10:47 +00:00
|
|
|
DEVICE_PACKAGES := kmod-usb-core kmod-usb-ohci kmod-usb2 kmod-usb-ledtrig-usbport kmod-leds-reset kmod-owl-loader
|
2019-01-02 22:19:04 +00:00
|
|
|
$(Device/netgear_ath79)
|
2018-08-11 11:47:21 +00:00
|
|
|
endef
|
|
|
|
|
|
ath79: add support for Netgear EX6400 and EX7300
This is sold as a dual-band 802.11ac range extender. It has a sliding
switch for Extender mode or Access Point mode, a WPS button, a recessed
Reset button, a hard-power button, and a multitude of LED's, some
multiplexed via an NXP 74AHC164D chip. The internal serial header pinout is
Vcc, Tx, Rx, GND, with GND closest to the corner of the board. You may
connect at 115200 bps, 8 data bits, no parity, 1 stop bit.
Specification:
- System-On-Chip: QCA9558
- CPU/Speed: 720 MHz
- Flash-Chip: Winbond 25Q128FVSG
- Flash size: 16 MiB
- RAM: 128 MiB
- Wireless No1: QCA9558 on-chip 2.4GHz 802.11bgn, 3x3
- Wireless No2: QCA99x0 chip 5GHz 802.11an+ac, 4x4
- PHY: Atheros AR8035-A
Installation:
If you can get to the stock firmware's firmware upgrade option, just feed
it the factory.img and boot as usual. As an alternative, TFTP the
factory.img to the bootloader.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[whitespace fix in DTS and reorder of make variables]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-09-14 04:08:51 +00:00
|
|
|
define Device/netgear_ex7300_ex6400
|
|
|
|
|
ATH_SOC := qca9558
|
|
|
|
|
NETGEAR_KERNEL_MAGIC := 0x27051956
|
|
|
|
|
NETGEAR_BOARD_ID := EX7300series
|
|
|
|
|
NETGEAR_HW_ID := 29765104+16+0+128
|
|
|
|
|
IMAGE_SIZE := 15552k
|
|
|
|
|
IMAGE/default := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | netgear-rootfs | pad-rootfs
|
|
|
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca99x0-ct
|
|
|
|
|
$(Device/netgear_ath79)
|
|
|
|
|
endef
|
|
|
|
|
|
|
|
|
|
define Device/netgear_ex6400
|
|
|
|
|
$(Device/netgear_ex7300_ex6400)
|
|
|
|
|
DEVICE_TITLE := NETGEAR EX6400
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += netgear_ex6400
|
|
|
|
|
|
|
|
|
|
define Device/netgear_ex7300
|
|
|
|
|
$(Device/netgear_ex7300_ex6400)
|
|
|
|
|
DEVICE_TITLE := NETGEAR EX7300
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += netgear_ex7300
|
|
|
|
|
|
2018-08-11 22:18:53 +00:00
|
|
|
define Device/netgear_wndr3700
|
|
|
|
|
$(Device/netgear_wndr3x00)
|
|
|
|
|
DEVICE_TITLE := NETGEAR WNDR3700
|
|
|
|
|
NETGEAR_KERNEL_MAGIC := 0x33373030
|
|
|
|
|
NETGEAR_BOARD_ID := WNDR3700
|
|
|
|
|
IMAGE_SIZE := 7680k
|
|
|
|
|
IMAGES += factory-NA.img
|
|
|
|
|
IMAGE/factory-NA.img := $$(IMAGE/default) | netgear-dni NA | check-size $$$$(IMAGE_SIZE)
|
|
|
|
|
SUPPORTED_DEVICES += wndr3700
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += netgear_wndr3700
|
|
|
|
|
|
|
|
|
|
define Device/netgear_wndr3700v2
|
|
|
|
|
$(Device/netgear_wndr3x00)
|
|
|
|
|
DEVICE_TITLE := NETGEAR WNDR3700v2
|
|
|
|
|
NETGEAR_KERNEL_MAGIC := 0x33373031
|
|
|
|
|
NETGEAR_BOARD_ID := WNDR3700v2
|
|
|
|
|
NETGEAR_HW_ID := 29763654+16+64
|
|
|
|
|
IMAGE_SIZE := 15872k
|
2019-11-14 16:26:44 +00:00
|
|
|
SUPPORTED_DEVICES += wndr3700
|
2018-08-11 22:18:53 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += netgear_wndr3700v2
|
|
|
|
|
|
2018-08-12 14:32:01 +00:00
|
|
|
define Device/pisen_wmm003n
|
|
|
|
|
$(Device/tplink-8mlzma)
|
|
|
|
|
ATH_SOC := ar9331
|
|
|
|
|
DEVICE_TITLE := Pisen WMM003N (Cloud Easy Power)
|
|
|
|
|
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-chipidea2
|
|
|
|
|
TPLINK_HWID := 0x07030101
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += pisen_wmm003n
|
|
|
|
|
|
2018-08-11 11:47:21 +00:00
|
|
|
define Device/netgear_wndr3800
|
|
|
|
|
$(Device/netgear_wndr3x00)
|
|
|
|
|
DEVICE_TITLE := NETGEAR WNDR3800
|
|
|
|
|
NETGEAR_KERNEL_MAGIC := 0x33373031
|
|
|
|
|
NETGEAR_BOARD_ID := WNDR3800
|
|
|
|
|
NETGEAR_HW_ID := 29763654+16+128
|
|
|
|
|
IMAGE_SIZE := 15872k
|
2019-11-14 16:26:44 +00:00
|
|
|
SUPPORTED_DEVICES += wndr3700
|
2018-05-06 08:20:11 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += netgear_wndr3800
|
|
|
|
|
|
2018-08-02 07:14:10 +00:00
|
|
|
define Device/phicomm_k2t
|
2018-06-13 13:14:49 +00:00
|
|
|
ATH_SOC := qca9563
|
|
|
|
|
DEVICE_TITLE := Phicomm K2T
|
|
|
|
|
IMAGE_SIZE := 15744k
|
2018-12-06 11:07:56 +00:00
|
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata | check-size $$$$(IMAGE_SIZE)
|
2019-12-24 12:04:26 +00:00
|
|
|
DEVICE_PACKAGES := kmod-leds-reset kmod-ath10k-ct-smallbuffers ath10k-firmware-qca9888-ct
|
2018-06-13 13:14:49 +00:00
|
|
|
endef
|
2018-08-02 07:14:10 +00:00
|
|
|
TARGET_DEVICES += phicomm_k2t
|
2018-09-04 21:27:02 +00:00
|
|
|
|
ath79: add support for ROSINSON WR818 board
This commit adds support for the ROSINSON WR818 WiFi-Router
SoC: Qualcomm Atheros QCA9563,
FLASH: Winbond W25Q128FV 16MBytes,
WiFi: QCA9563 b/g/n 3x3 450Mbit/s,
USB: 1x USB 2.0 Type A, 1x USB2.0 Type C,
IN: WPS/Reset button GPIO1,
OUT: Power LED red, Internet LED red, WLAN LED red,
LAN1 LED red, LAN2 LED red, System LED red,
UART: RX-GPIO18, TX-GPIO22,
Tested and working:
- Ethernet (LAN + WAN)
- WiFi
- OpenWRT sysupgrade
- Button
- LEDs
Installation of OpenWRT from vendor firmware:
- Connect to the Web-interface at http://192.168.1.1
- Go to "Administration" -> "Firmware Upgrade"
- Upload the OpenWrt sysupgrade image
Signed-off-by: Rosy Song <rosysong@rosinson.com>
2018-10-07 04:04:54 +00:00
|
|
|
define Device/rosinson_wr818
|
|
|
|
|
ATH_SOC := qca9563
|
|
|
|
|
DEVICE_TITLE := ROSINSON WR818
|
|
|
|
|
IMAGE_SIZE := 15872k
|
|
|
|
|
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-ledtrig-usbport
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += rosinson_wr818
|
|
|
|
|
|
2019-05-25 12:36:05 +00:00
|
|
|
define Device/wd_mynet-n750
|
|
|
|
|
$(Device/seama)
|
|
|
|
|
ATH_SOC := ar9344
|
|
|
|
|
DEVICE_TITLE := Western Digital My Net N750
|
|
|
|
|
IMAGE_SIZE := 15872k
|
|
|
|
|
DEVICE_PACKAGES := kmod-usb-core kmod-usb2
|
|
|
|
|
SEAMA_SIGNATURE := wrgnd13_wd_av
|
|
|
|
|
SUPPORTED_DEVICES += mynet-n750
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += wd_mynet-n750
|
|
|
|
|
|
2018-09-04 21:27:02 +00:00
|
|
|
define Device/wd_mynet-wifi-rangeextender
|
|
|
|
|
ATH_SOC := ar9344
|
|
|
|
|
DEVICE_TITLE := Western Digital My Net Wi-Fi Range Extender
|
|
|
|
|
DEVICE_PACKAGES := rssileds nvram -swconfig
|
|
|
|
|
IMAGE_SIZE := 7808k
|
|
|
|
|
ADDPATTERN_ID := mynet-rext
|
|
|
|
|
ADDPATTERN_VERSION := 1.00.01
|
|
|
|
|
IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | cybertan-trx | \
|
|
|
|
|
addpattern | append-metadata
|
|
|
|
|
SUPPORTED_DEVICES += mynet-rext
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += wd_mynet-wifi-rangeextender
|
2018-10-30 16:05:43 +00:00
|
|
|
|
|
|
|
|
define Device/winchannel_wb2000
|
|
|
|
|
ATH_SOC := ar9344
|
|
|
|
|
DEVICE_TITLE := Winchannel WB2000
|
|
|
|
|
IMAGE_SIZE := 15872k
|
|
|
|
|
DEVICE_PACKAGES := kmod-i2c-core kmod-i2c-gpio kmod-rtc-ds1307 kmod-usb2 kmod-usb-ledtrig-usbport
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += winchannel_wb2000
|
2019-02-01 19:48:41 +00:00
|
|
|
|
|
|
|
|
define Device/xiaomi_mi-router-4q
|
|
|
|
|
ATH_SOC := qca9561
|
|
|
|
|
DEVICE_TITLE := Xiaomi Mi Router 4Q
|
|
|
|
|
IMAGE_SIZE := 14336k
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += xiaomi_mi-router-4q
|
ath79: add support for YunCore A770
YunCore A770 is a ceiling AC750 AP with 2 Fast Ethernet ports, PoE
(802.3at) support, based on QCA9531 + QCA9887.
Specification:
- 650/597/216 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of flash (SPI NOR)
- 2x 10/100 Mbps Ethernet (PoE 802.3at support in WAN port)
- 2T2R 2.4 GHz (QCA9531), with ext. PA and LNA
- 1T1R 5 GHz (QCA9887), with ext. FEM (SKY85728-11)
- 2x regular LED, 1x RGB LED (all driven by GPIO)
- 1x button (reset)
- DC jack for main power input (12 V)
- UART header on PCB
Flash instruction:
1. First, gain root access to the device, following below steps:
- Login into web gui (default password/IP: admin/192.168.188.253).
- Go to 'Advanced' -> 'Management' -> 'System' and download backup of
configuration (bakfile.bin).
- Open the file as tar.gz archive, edit/update 'shadow' file and change
hash of root password to something known.
- Repack the archive, rename it back to 'bakfile.bin' and use to
restore configuration of the device.
- After that, device will reboot and can be accessed over SSH.
2. Then, install OpenWrt:
- Login over SSH and issue command:
fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
- Upload 'sysupgrade' image and install it (only if previous command
succeeded) with command: 'sysupgrade -n -F openwrt-...'.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-03-09 15:31:17 +00:00
|
|
|
|
|
|
|
|
define Device/yuncore_a770
|
|
|
|
|
ATH_SOC := qca9531
|
|
|
|
|
DEVICE_TITLE := YunCore A770
|
|
|
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9887-ct
|
|
|
|
|
IMAGE_SIZE := 16000k
|
2019-08-12 23:26:45 +00:00
|
|
|
IMAGES += tftp.bin
|
|
|
|
|
IMAGE/tftp.bin := $$(IMAGE/sysupgrade.bin) | yuncore-tftp-header-16m
|
ath79: add support for YunCore A770
YunCore A770 is a ceiling AC750 AP with 2 Fast Ethernet ports, PoE
(802.3at) support, based on QCA9531 + QCA9887.
Specification:
- 650/597/216 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of flash (SPI NOR)
- 2x 10/100 Mbps Ethernet (PoE 802.3at support in WAN port)
- 2T2R 2.4 GHz (QCA9531), with ext. PA and LNA
- 1T1R 5 GHz (QCA9887), with ext. FEM (SKY85728-11)
- 2x regular LED, 1x RGB LED (all driven by GPIO)
- 1x button (reset)
- DC jack for main power input (12 V)
- UART header on PCB
Flash instruction:
1. First, gain root access to the device, following below steps:
- Login into web gui (default password/IP: admin/192.168.188.253).
- Go to 'Advanced' -> 'Management' -> 'System' and download backup of
configuration (bakfile.bin).
- Open the file as tar.gz archive, edit/update 'shadow' file and change
hash of root password to something known.
- Repack the archive, rename it back to 'bakfile.bin' and use to
restore configuration of the device.
- After that, device will reboot and can be accessed over SSH.
2. Then, install OpenWrt:
- Login over SSH and issue command:
fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
- Upload 'sysupgrade' image and install it (only if previous command
succeeded) with command: 'sysupgrade -n -F openwrt-...'.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-03-09 15:31:17 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += yuncore_a770
|
ath79: Add support for ZBT-WD323
ZBT-WD323 is a dual-LTE router based on AR9344. The detailed
specifications are:
* AR9344 560MHz/450MHz/225MHz (CPU/DDR/AHN).
* 128 MB RAM
* 16MB of flash(SPI-NOR, 22MHz)
* 1x 2.4GHz wifi (Atheros AR9340)
* 3x 10/100Mbos Ethernet (AR8229)
* 1x USB2.0 port
* 2x miniPCIe-slots (USB2.0 only)
* 2x SIM slots (standard size)
* 4x LEDs (1 gpio controlled)
* 1x reset button
* 1x 10 pin terminal block (RS232, RS485, 4x GPIO)
* 2x CP210x UART bridge controllers (used for RS232 and RS485)
* 1x 2 pin 5mm industrial interface (input voltage 12V~36V)
* 1x DC jack
* 1x RTC (PCF8563)
Tested:
- Ethernet switch
- Wifi
- USB port
- MiniPCIe-slots (+ SIM slots)
- Sysupgrade
- Reset button
- RS232
Intallation and recovery:
The board ships with OpenWRT, but sysupgrade does not work as a
different firmware format than what is expected is generated. The
easiest way to install (and recover) the router, is to use the
web-interface provided by the bootloader (Breed).
While the interface is in Chinese, it is easy to use. First, in order to
access the interface, you need to hold down the reset button for around
five seconds. Then, go to 192.168.1.1 in your browser. Click on the
second item in the list on the left to access the recovery page. The
second item on the next page is where you select the firmware. Select
the menu item containing "Atheros SDK" and "16MB" in the dropdown close
to the buttom, and click on the button at the bottom to start
installation/recovery.
Notes:
* RS232 is available on /dev/ttyUSB0 and RS485 on /dev/ttyUSB1
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
[removed unused poll-interval from gpio-keys, i2c-gpio 4.19 compat]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-05-31 13:43:14 +00:00
|
|
|
|
ath79: add support for YunCore XD4200 and A782
YunCore XD4200 ('XD4200_W6.0' marking on PCB) is Qualcomm/Atheros based
(QCA9563, QCA9886, QCA8334) dual-band, Wave-2 AC1200 ceiling AP with PoE
(802.3at) support. A782 model ('T750_V5.1' marking on PCB) is a smaller
version of the XD4200, with similar specification but lower TX power.
Specification:
- QCA9563 (775 MHz)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100/1000 Mbps Ethernet (QCA8334), with 802.3at PoE support (WAN)
- Wi-Fi 2.4 GHz:
- XD4200: 2T2R (QCA9563), with ext. PA (SKY65174-21) and LNA
- A782: 2T2R (QCA9563), with ext. FEM (SKY85329-11)
- Wi-Fi 5 GHz:
- XD4200: 2T2R (QCA9886), with ext. FEM (SKY85728-11)
- A782: 2T2R (QCA9886), with ext. FEM (SKY85735-11)
- LEDs:
- XD4200: 5x (2x driven by SOC, 1x driven by AC radio, 2x Ethernet)
- A782: 3x (1x RGB, driven by SOC and radio, 2x Ethernet)
- 1x button (reset)
- 1x UART (4-pin, 2.54 mm pitch) header on PCB
- 1x DC jack (12 V)
Flash instructions:
If your device comes with generic QSDK based firmware, you can login
over telnet (login: root, empty password, default IP: 192.168.188.253),
issue first (important!) 'fw_setenv' command and then perform regular
upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download
image to the device, SSH server is not available):
fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin
In case your device runs firmware with YunCore custom GUI, you can use
U-Boot recovery mode:
1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with
'tftp' image renamed to 'upgrade.bin'
2. Power the device with reset button pressed and release it after 5-7
seconds, recovery mode should start downloading image from server
(unfortunately, there is no visible indication that recovery got
enabled - in case of problems check TFTP server logs)
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
(backported from commit e5d4c0966736287c7ade29c5ccaf6f1ad841b7db)
2019-11-12 21:36:28 +00:00
|
|
|
define Device/yuncore_a782
|
|
|
|
|
ATH_SOC := qca9563
|
|
|
|
|
DEVICE_TITLE := YunCore A782
|
|
|
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
|
|
|
|
|
IMAGE_SIZE := 16000k
|
|
|
|
|
IMAGES += tftp.bin
|
|
|
|
|
IMAGE/tftp.bin := $$(IMAGE/sysupgrade.bin) | yuncore-tftp-header-16m
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += yuncore_a782
|
|
|
|
|
|
|
|
|
|
define Device/yuncore_xd4200
|
|
|
|
|
ATH_SOC := qca9563
|
|
|
|
|
DEVICE_TITLE := YunCore XD4200
|
|
|
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
|
|
|
|
|
IMAGE_SIZE := 16000k
|
|
|
|
|
IMAGES += tftp.bin
|
|
|
|
|
IMAGE/tftp.bin := $$(IMAGE/sysupgrade.bin) | yuncore-tftp-header-16m
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += yuncore_xd4200
|
|
|
|
|
|
ath79: Add support for ZBT-WD323
ZBT-WD323 is a dual-LTE router based on AR9344. The detailed
specifications are:
* AR9344 560MHz/450MHz/225MHz (CPU/DDR/AHN).
* 128 MB RAM
* 16MB of flash(SPI-NOR, 22MHz)
* 1x 2.4GHz wifi (Atheros AR9340)
* 3x 10/100Mbos Ethernet (AR8229)
* 1x USB2.0 port
* 2x miniPCIe-slots (USB2.0 only)
* 2x SIM slots (standard size)
* 4x LEDs (1 gpio controlled)
* 1x reset button
* 1x 10 pin terminal block (RS232, RS485, 4x GPIO)
* 2x CP210x UART bridge controllers (used for RS232 and RS485)
* 1x 2 pin 5mm industrial interface (input voltage 12V~36V)
* 1x DC jack
* 1x RTC (PCF8563)
Tested:
- Ethernet switch
- Wifi
- USB port
- MiniPCIe-slots (+ SIM slots)
- Sysupgrade
- Reset button
- RS232
Intallation and recovery:
The board ships with OpenWRT, but sysupgrade does not work as a
different firmware format than what is expected is generated. The
easiest way to install (and recover) the router, is to use the
web-interface provided by the bootloader (Breed).
While the interface is in Chinese, it is easy to use. First, in order to
access the interface, you need to hold down the reset button for around
five seconds. Then, go to 192.168.1.1 in your browser. Click on the
second item in the list on the left to access the recovery page. The
second item on the next page is where you select the firmware. Select
the menu item containing "Atheros SDK" and "16MB" in the dropdown close
to the buttom, and click on the button at the bottom to start
installation/recovery.
Notes:
* RS232 is available on /dev/ttyUSB0 and RS485 on /dev/ttyUSB1
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
[removed unused poll-interval from gpio-keys, i2c-gpio 4.19 compat]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-05-31 13:43:14 +00:00
|
|
|
define Device/zbtlink_zbt-wd323
|
|
|
|
|
ATH_SOC := ar9344
|
|
|
|
|
DEVICE_TITLE := ZBT WD323
|
|
|
|
|
IMAGE_SIZE := 16000k
|
|
|
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-i2c-core kmod-i2c-gpio kmod-rtc-pcf8563 \
|
|
|
|
|
kmod-usb-serial kmod-usb-serial-cp210x uqmi
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += zbtlink_zbt-wd323
|
