ExternalVendorCode/openwrt
1
0
Fork 0
mirror of https://github.com/openwrt/openwrt.git synced 2024-12-27 09:12:39 +00:00
Code Issues Actions 4 Packages Projects Releases Wiki Activity
70fd815e57
openwrt/package/boot/uboot-envtools/files/qualcommax_ipq807x

65 lines
1.5 KiB
Plaintext
Raw Normal View History

ipq807x: add Xiaomi AX3600 Xiaomi AX3600 is a budget 802.11ax dual-band router/AP. Specifications: * CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz * RAM: 512MB of DDR3 * Storage: 256MB of parallel NAND * Ethernet: 4x1G RJ45 ports (QCA8075) with 1x status LED per port * WLAN: * PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT * 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate * 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate * LED-s: * System (Blue and Yellow) * IoT (Blue) * Network (Blue and Yellow) * Buttons: 1x Soft reset * Power: 12V DC Jack Installation instructions: Obtaining SSH access is mandatory https://openwrt.org/inbox/toh/xiaomi/xiaomi_ax3600#obtain_ssh_access Installation is done by the ubiformat method, through SSH: 1. Open an SSH shell to the router 2. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi to the /tmp directory 3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1): nvram get flag_boot_rootfs 4. Find the rootfs and rootfs_1 mtd indexes respectively: cat /proc/mtd Please confirm if mtd12 and mtd13 are the correct indexes from above! 5. Use the command ubiformat to flash the opposite mtd with UBI image: If nvram get flag_boot_rootfs returned 0: ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit otherwise: ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit 6. Reboot the device by: reboot Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages. Continue in order to pernamently flash OpenWrt: 7. SSH into OpenWrt from one of the LAN ports 8. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin to the /tmp directory 9. Sysupgrade the device: sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Signed-off-by: Robert Marko <robimarko@gmail.com>
2021-05-19 19:04:43 +00:00
[ -e /etc/config/ubootenv ] && exit 0
touch /etc/config/ubootenv
. /lib/uboot-envtools.sh
. /lib/functions.sh
board=$(board_name)
case "$board" in
ipq807x: add support for Netgear WAX218 Netgear WAX218 is a 802.11ax AP claiming AX3600 support. It is wall or ceiling mountable. It can be powered via PoE, or a 12 V adapter. The board has footprints for 2.54mm UART headers. They're difficult to solder because the GND is connected to a large copper plane. Only try soldering if you are very skilled. Otherwise, use pogo pins. Specifications: --------------- * CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz * RAM: 366 MB of RAM available to OS, not sure of total amount * Storage: Macronix MX30UF2G18AC 256MB NAND * Ethernet: * 2.5G RJ45 port (QCA8081) with PoE input * WLAN: * 2.4GHz/5GHz with 8 antennas * LEDs: * Power (Amber) * LAN (Blue) * 2G WLAN (Blue) * 5G WLAN (Blue) * Buttons: * 1x Factory reset * Power: 12V DC Jack * UART: Two 4-pin unpopulated headers near the LEDs * "J2 UART" is the CPU UART, 3.3 V level Installation: ============= Web UI method ------------- Flashing OpenWRT using the vendor's Web UI is problematic on this device. The u-boot mechanism for communicating the active rootfs is antiquated and unreliable. Instead of setting the kernel commandline, it relies on patching the DTS partitions of the nand node. The way partitions are patched is incompatible with newer kernels. Newer kernels use the SMEM partition table, which puts "rootfs" on mtd12. The vendor's Web UI will flash to either mtd12 or mtd14. One reliable way to boot from mtd14 and avoid boot loops is to use an initramfs image. 1. In the factory web UI, navigate to System Manager -> Firmware. 2. In the "Local Firmware Upgrade" section, click Browse 3. Navigate and select the 'web-ui-factory.fit' image 4. Click "Upload" 5. On the following page, click on "Proceed" The flash proceeds at this point and the system will reboot automatically to OpenWRT. 6. Flash the 'nand-sysupgrade.bin' using Luci or the commandline SSH method ---------- Enable SSH using the CLI or Web UI. The root account is locked out to ssh, and the admin account defaults to Netgear's CLI application. So we need to get creative: First, make sure the device boots from the second firmware partition: ssh -okexalgorithms=diffie-hellman-group14-sha1 admin@<ipaddr> \ /usr/sbin/fw_setenv active_fw 1 Then reboot the device, and run the update: scp -O -o kexalgorithms=diffie-hellman-group14-sha1 \ -o hostkeyalgorithms=ssh-rsa \ netgear_wax218-squashfs-nand-factory.ubi \ admin@<ipaddr>:/tmp/openwrt.ubi ssh -okexalgorithms=diffie-hellman-group14-sha1 admin@<ipaddr> \ /usr/sbin/ubiformat /dev/mtd12 -f /tmp/openwrt.ubi ssh -okexalgorithms=diffie-hellman-group14-sha1 admin@<ipaddr> \ /usr/sbin/fw_setenv active_fw 0 Now reboot the device, and it should boot into a ready-to-use OpenWRT. Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-by: Robert Marko <robimarko@gmail.com> Tested-by: Francisco G Luna <frangonlun@gmail.com>
2022-06-02 16:35:26 +00:00
dynalink,dl-wrx36|\
ipq807x: add support for Netgear RAX120v2 Netgear Nighthawk RAX120v2 AX WIFI router with 5 1G and 1 5G ports. The majority of the code is based on @jewwest's PR #11830. Specifications: * CPU: Qualcomm IPQ8074 Quad core Cortex-A53 2.2GHz * RAM: 1024MB of DDR3 (Nanya NT5CC256M16EP-EK × 2) * Flash: SPI-NAND 512 MiB (Winbond W29N04GZBIBA) * Ethernet: 4x 10/100/1000 Mbps LAN, 1x 10/100/1000 Mbps WAN (Qualcomm QCA8075), 1x 10/100/1000/2500/5000 Mbps LAN/WAN (Aquantia AQR111B0 PHY) * Wi-Fi: * 2.4 GHz: Qualcomm QCN5024 4x4 * 2x 5 GHz: Qualcomm QCN5054 4x4 * USB: 2x USB 3.0 * LEDs: Power, 2.4GHz & 5GHz Radio, WPS, WAN, USB1 & USB2, 5G LAN * Keys: LEDs On/Off, Power, Reset, RFKILL, WPS * UART: Marked J9003 VCC TX RX GND, beginning from "1". 3.3v, 115200n8 * Power: 19 VDC, 3.1 A Installation: * Flashing OpenWrt is done in two steps: a) Flash *-squashfs-web-ui-factory.img from stock UI (thanks to @wangyu-). This writes an initramfs based OpenWrt image onto the RAX120v2 b) From OpenWrt flash the *-squashfs-sysupgrade.bin using LuCI or the commandline * U-Boot allows booting an initramfs image via TFTP: - Set ip of your PC to 192.168.1.100 - At the serial console interrupt boot at "Hit any key to stop autoboot:" - In u-boot run `tftpsrv` - On your PC send the OpenWrt initramfs image: tftp 192.168.1.1 -m binary -c put openwrt-ipq807x-generic-netgear_rax120v2-initramfs-uImage.itb Make 5G Aquantia phy work: For the 5G port labeled 'lan5' to work a firmware is needed. This can be loaded in u-boot by writing the firmware to the correct mtd partition. The firmware file found in the Netgear stock firmware under /lib/firmware/ named 'AQR-G3_v4.3.C-AQR_DNI_DR-EQ35AX8-R-prov1_ID23888_VER1311.cld' is needed and has to be converted to a MBN file. The `mkheader.py` script used here can be found in the Netgear V1.2.8.40 GPL source, under 'git_home/u-boot.git/tools/mkheader.py' Convert the CLD file to MBN using: $ python2 mkheader.py 0x44000000 0x13 <*.cld file> aqr_4.3.C.mbn This MBN file can then be flashed to the MTD partition to be used by u-boot. The necessary files can also be found in https://github.com/boretom/openwrt-fork/tree/rax120v2/aquantia-firmware * Write MBN file to MTD partition to be loaded automatically by u-boot: U-boot automatically tries to load the firmware from nand at address 0x7e00000 which corresponds to `/dev/mtd25` in OpenWrt. - find ETHPHYFW partition while running OpenWrt (expected: /dev/mtd25) $ fgrep -i 'ethphyfw' /proc/mtd mtd25: 00080000 00020000 "ethphyfw - copy mbn file to /tmp/ folder of the router $ scp aqr-v4.3.C.mbn 192.168.1.1:/tmp/ - write mbn file to ethphyfw partition $ mtd write /tmp/aqr_v4.3.C.mbn /dev/mtd25 Revert to stock firmware: * Flash the stock firmware to the bootloader using TFTP/NMRP. References to RAX120v2 GPL source: https://www.downloads.netgear.com/files/GPL/RAX120-V1.2.8.40_gpl_src.zip Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Thomas Kupper <thomas.kupper@gmail.com>
2023-05-05 15:04:33 +00:00
netgear,rax120v2|\
ipq807x: add support for Netgear WAX620 ``` Specifications: * CPU: Qualcomm IPQ8072A, SoC Version: 2.0, Quad core Cortex-A53 1.6896 GHz * RAM: 1 GiB of DDR4 600 MHz * Flash: NAND 2x256 MiB (Macronix MX30UF2G18AC) * 4 RGB LEDs: Power, LAN, 2.4GHz and 5GHz * UART: Two 4-pin unpopulated headers under the LEDs. Use the header closest to LED 4 and 5. They are marked with a white stroke. TX RX GND, beginning from "4". 115200n8. Lan: * One 100/1000/2.5GBASE-T Gigabit Ethernet (QCA8081) Wlan: * 4x4 in 2.4GHz: 802.11b/g/n/ax * 4x4 in 5.0GHz: 802.11a/n/ac/ax * OFDM and OFDMA * Bidir and MU-MIMO * Internal antenna 3.1/4.3 dBi (2.4GHz/5GHz) Power: * PoE+ 802.3at/af 25.5W * DC 12V 2.5A ``` ``` Note: The OpenWrt image is setup with DHCP and not a static IP. 1. Download the OpenWrt initramfs image. Copy the image to a TFTP server 2. Connect to console on the AP, and connect the LAN port to your LAN 3. Stop auto boot to get to U-boot shell, interrupt the autoboot process by pressing '0' when prompted 4. Set active_fw in env # setenv active_fw 1 5. Transfer the initramfs image with TFTP # setenv serverip 192.168.1.10 (IP of TFTP server host) # setenv ipaddr 192.168.1.1 (IP used by the router for getting the image, must be in the same subnet as the TFTP host) # tftpboot openwrt-qualcommax-ipq807x-netgear_wax620-initramfs-uImage.itb 6. Reboot and load the image # bootm 7. SCP factory image to the AP # scp openwrt-qualcommax-ipq807x-netgear_wax620-squashfs-factory.ubi root@192.168.1.1:/tmp/ 8. Connect to device using SSH (use the LAN port) 9. Flash squashfs-factory.ubi from within the initramfs instance of OpenWRT Before you flash, please check your mtd partitions where mtdX is the right mtd rootfs partition. # cat /proc/mtd (To check MTD partitions) # ubiformat /dev/mtd19 -y -f /tmp/openwrt-qualcommax-ipq807x-netgear_wax620-squashfs-factory.ubi 10. Set active_fw to 0 # /usr/sbin/fw_setenv active_fw 0 11. Reboot the AP and your done # reboot ``` Signed-off-by: Kristian Skramstad <kristian+github@83.no>
2023-08-21 15:45:36 +00:00
netgear,wax218|\
qualcommax: ipq807x: add support for Netgear WAX630 ``` Specifications: * CPU: Qualcomm IPQ8074A, SoC Version: 2.0, Quad core 1651 MHz * RAM: 1 GiB of DDR3 466 MHz * Flash: NAND 512 MiB (Winbond W29N04GZ) * 6 RGB LEDs: Power, LAN1, LAN2, 2.4GHz, 5GHz H and 5GHz L * UART: One 4-pin populated header next to the heatsink and a chip. GND RXD TXD, beginning from the external antennas. 115200n8. Lan: * One 100/1000/2.5GBASE-T Gigabit Ethernet 802.3bt/at * One 100/1000 Gigabit Ethernet Wlan: * 4x4 in 2.4GHz : 802.11b/g/n/ax * 4x4 in 5.0GHz L: 802.11a/n/ac/ax * 4x4 in 5.0GHz H: 802.11a/n/ac/ax * OFDM and OFDMA * Bidir and MU-MIMO * Internal antenna 2.86/4.41/4.98 dBi (2.4GHz/5GHz L/5GHz H) Power: * 802.3bt/at 30.1W * DC 12V/3.5A Mounting: Wall and ceiling ``` ``` 1. Download the OpenWrt initramfs image. Copy the image to a TFTP server 2. Connect to the console on the AP, and connect the LAN port to your LAN 3. Stop auto boot to get to U-boot shell, interrupt the autoboot process by pressing '0' when prompted 4. Set active_fw in env 4. Set active_fw in env # setenv active_fw 1 5. Transfer the initramfs image with TFTP # setenv serverip 192.168.1.10 (IP of TFTP server host) # setenv ipaddr 192.168.1.1 (IP used by the router for getting the image, must be in the same subnet as the TFTP host) # tftpboot openwrt-qualcommax-ipq807x-netgear_wax630-initramfs-uImage.itb 6. Reboot and load the image # bootm 7. SCP factory image to the AP # scp openwrt-qualcommax-ipq807x-netgear_wax630-squashfs-factory.ubi root@192.168.1.1:/tmp/ 8. Connect to device using SSH (use the LAN port) 9. Flash squashfs-factory.ubi from within the initramfs instance of OpenWRT Before you flash, please check your mtd partitions where mtdX is the right mtd rootfs partition. # cat /proc/mtd (To check MTD partitions) # ubiformat /dev/mtd18 -y -f /tmp/openwrt-qualcommax-ipq807x-netgear_wax630-squashfs-factory.ubi 10. Set active_fw to 0 # /usr/sbin/fw_setenv active_fw 0 11. Reboot the AP and your done # reboot ``` Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Kristian Skramstad <kristian+github@83.no>
2023-10-01 14:28:24 +00:00
netgear,wax620|\
netgear,wax630)
ipq807x: add Dynalink DL-WRX36 Dynalink DL-WRX36 is a AX WIFI router with 4 1G and 1 2.5G ports. Specifications: • CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz • RAM: 1024MB of DDR3 • Storage: 256MB Nand • Ethernet: 4x 1G RJ45 ports (QCA8075) + 1 2.5G Port (QCA8081) • WLAN: 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 1174 Mbps PHY rate 5GHz: Qualcomm QCN5054 4x4 802.11a/b/g/n/ac/ax 2402 PHY rate • 1x USB 3.0 • 1 gpio-controlled dual color led (blue/red) • Buttons: 1x soft reset / 1x WPS • Power: 12V DC jack A poulated serial header is onboard (J1004) the connector size is a 4-pin 2.0 mm JST PH. RX/TX is working, u-boot bootwait is active, secure boot is enabled. Notes: - Serial is completely deactivated in the stock firmware image. - This commit adds only single partition support, that means sysupgrade is upgrading the current rootfs partition. - Installation can be done by serial connection or SSH access on OEM firmware Installation Instructions: Most part of the installation is performed from an initramfs image running OpenWrt, and there are two options to boot it. Boot initramfs option 1: Using serial connection (3.3V) 1. Stop auto boot to get to U-boot shell 2. Transfer initramfs image to device (openwrt-ipq807x-generic-dynalink_dl-wrx36-initramfs-uImage.itb) Tested using TFTP and a FAT-formatted USB flash drive. 3. Boot the initramfs image # bootm Boot initramfs option 2: From SSH access on OEM firmware 1. Copy the initramfs image to a FAT-formatted flash drive (tested on single-partition drive) and connect it to device USB port. 2. Change boot command so it loads the initramfs image on next boot Fallback to OEM firmware is provided. # fw_setenv bootcmd 'usb start && fatload usb 0:1 0x44000000 openwrt-ipq807x-generic-dynalink_dl-wrx36-initramfs-uImage.itb && bootm 0x44000000; bootipq' 3. Reboot the device to boot the initramfs # reboot Install OpenWrt from initramfs image: 1. Use SCP (or other way) to transfer OpenWrt factory image 2. Connect to device using SSH (on a LAN port) 3. Check MTD partition table. rootfs and rootfs_1 should be mtd18 and mtd20 depending on current OEM slot. # cat /proc/mtd 4. Do a ubiformat to both rootfs partitions: # ubiformat /dev/mtd18 -y -f /path_to/factory_image # ubiformat /dev/mtd20 -y -f /path_to/factory_image 5. Set U-boot env variable: mtdids # fw_setenv mtdids 'nand0=nand0' 6. Get offset of mtd18 to determine current OEM slot - If current OEM slot is 1, offset is 16777216 (0x1000000) - If current OEM slot is 2, offset is 127926272 (0x7a00000) # cat /sys/class/mtd/mtd18/offset 7. Set U-boot env variable: mtdparts If current OEM slot is 1, run: # fw_setenv mtdparts 'mtdparts=nand0:0x6100000@0x1000000(fs),0x6100000@0x7a00000(fs_1)' If current OEM slot is 2, run: # fw_setenv mtdparts 'mtdparts=nand0:0x6100000@0x7a00000(fs),0x6100000@0x1000000(fs_1)' 8. Set U-boot env variable: bootcmd # fw_setenv bootcmd 'setenv bootargs console=ttyMSM0,115200n8 ubi.mtd=rootfs rootfstype=squashfs rootwait; ubi part fs; ubi read 0x44000000 kernel; bootm 0x44000000#config@rt5010w-d350-rev0' 9. Reboot the device # reboot Note: this PR adds only single partition support, that means sysupgrade is upgrading the current rootfs partition Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
2022-08-05 09:38:37 +00:00
idx="$(find_mtd_index 0:appsblenv)"
[ -n "$idx" ] && \
ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x40000" "0x20000" "2"
;;
ipq807x: add support for Compex WPQ873 The Compex WPQ873 is a development board with two M.2 B-key slots for cellular modems. Device info: - IPQ8072A SoC - 512MiB RAM - 256MiB NAND flash - 8MiB SPI NOR - 3x 1GigE ports - 1x 2.5GigE port - 2.4GHz/5GHz AX WLAN - 1x USB 3.0 port - 1x M.2 B-key socket with PCIe 3.0 - 1x M.2 B-key socket with PCIe 2.0 and USB 3.0 - 4x SIM card slots - Bluetooth LE 5.0 (QCA4024) Prerequisites 1) TFTP server 2) 3.3V USB to TTL cable for UART console 2.54mm pitch 4-pin header for UART is readily provided on board, no modifications are necessary to access it TTL connector pinout: 2=TX, 3=RX, 4=GND Arrow marks pin 1 which is 3.3V Serial port settings: 115200 8N1 no flow control The device will most likely ship with a QSDK-based firmware. 1. Power on device and interrupt u-boot to obtain u-boot CLI 2. set serverip to IP address of the TFTP server, for example: `setenv serverip 192.168.1.10` 3. Download image from TFTP server: `tftpboot 0x44000000 openwrt-ipq807x-generic-compex_wpq873-squashfs-factory.ubi` 4. Flash ubi image to both partitions and reset: `sf probe imxtract 0x44000000 ubi nand device 0 nand erase 0x0 0x3400000 nand erase 0x3c00000 0x3400000 nand write $fileaddr 0x0 $filesize nand write $fileaddr 0x3c00000 $filesize reset` Afterwards, you can use sysupgrade to flash new OpenWRT images. Signed-off-by: Antti Nykänen <antti.nykanen@nokia.com>
2023-05-25 06:42:09 +00:00
compex,wpq873|\
ipq807x: Add ZyXEL NBG7815 ZyXEL NBG7815 is a premium 802.11ax "tri"-band router/AP. Specifications: * CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz * RAM: 1 GB 2x Nanya NT5CC256M16ER-EK * Storage: * 8MB serial flash Winbond W25Q64DW * 4GB eMMC flash Kingston EMMC04G-M627 * Ethernet: * 4x1G RJ45 ports (QCA8074A) with 1x status LED per port * 1x2.5G RJ45 port (QCA8081) with 1x status LED * 1x10G RJ45 port (AQR113C) with 1x status LED * Switch: Qualcomm Atheros QCA8075 * WLAN: * 2.4GHz: Qualcomm QCN5024 4x4@40MHz 802.11b/g/n/ax 1147 Mbps PHY rate * 2x 5GHz: Qualcomm QCN5054 4x4 802.11a/b/g/n/ac/ax 2402 PHY rate * Bluetooth CSR8811 using HSUART, currently unsupported * USB: 1x USB3.0 Type-A port * LED-s currently not supported: * White * Dark Blu * Amber * Purple * Purple and dark blue * Red * Buttons: * 1x Soft reset * Power: 12V DC Jack Installation instructions: * Disconnect WAN * Reset device to factory defaults by pushing reset button 15 sec, LEDs should lit orange color. * After 5-10 minutes, when the LEDs turn constant dark blue, put your LAN cable and connect at address 192.168.123.1 by telnet on port 23 * Login with NBG7815 login: root password: nbg7815@2019 * cd /tmp/ApplicationData * wget -O openwrt-ipq807x-generic-zyxel_nbg7815-squashfs-sysupgrade.bin http://... * wget https://github.com/itorK/nbg7815_tools/blob/main/flash_to_openwrt.sh * run flash_to_openwrt.sh If you can't use wget, you can transfer the files via nc. See https://openwrt.org/inbox/toh/zyxel/nbg7815_armor_g5 for installation details. Bluetooth usage: * you need at least package bluez-utils, recommended bluez-daemon * run following commands to enable and start hciattach /dev/ttyMSM1 bcsp hciconfig hci0 up Many thanks to itorK for his work on this device: https://github.com/itorK/openwrt/tree/nbg7815 Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: André Valentin <avalentin@marcant.net>
2023-01-03 18:23:41 +00:00
edgecore,eap102|\
zyxel,nbg7815)
ipq807x: add Edgecore EAP102 The Edgecore EAP102 is a wall/ceiling mountable AP. The AP can be powered by either PoE or AC adapter. Device info: - IPQ8071-A SoC - 1GiB RAM - 256MiB NAND flash - 32MiB SPI NOR - 2 Ethernet ports - 1 Console port - 2GHz/5GHz AX WLAN - 2 USB 2.0 ports Install instructions: Prerequistes - TFTP server, preferrably within 192.168.1.0/24 Console cable plugged in (115200 8N1 no flow control) 1. Power on device and interrupt u-boot to obtain u-boot CLI 2. set serverip to IP address of the TFTP server: `setenv serverip 192.168.1.250` 3. Download image from TFTP server: `tftpboot 0x44000000 openwrt-ipq807x-generic-edgecore_eap102-squashfs-nand-factory.ubi` 4. Flash ubi image to both partitions and reset: `sf probe imxtract 0x44000000 ubi nand device 0 nand erase 0x0 0x3400000 nand erase 0x3c00000 0x3400000 nand write $fileaddr 0x0 $filesize nand write $fileaddr 0x3c00000 $filesize reset` Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
2022-01-29 00:03:11 +00:00
idx="$(find_mtd_index 0:appsblenv)"
[ -n "$idx" ] && \
ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x10000" "0x10000" "1"
;;
ipq807x: add Edimax CAX1800 Edimax CAX1800 is a 802.11 ax dual-band AP with PoE. AP can be ceiling or wall mount. Specifications: • CPU: Qualcomm IPQ8070A Quad core Cortex-A53 1.4GHz • RAM: 512MB of DDR3 • Storage: 128MB NAND (contains rootfs) / 8MB NOR (contains art and uboot-env) • Ethernet: 1x 1G RJ45 port (QCA8072) PoE • WLAN: 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate 5GHz: Qualcomm QCN5054 2x2 802.11a/b/g/n/ac/ax 1201 PHY rate • LEDs: 3 x GPIO-controlled System-LEDs (form one virtual RGB System-LED) black_small_square Buttons: 1x soft reset black_small_square Power: 12V DC jack or PoE (802.3af ) An unpopulated serial header is onboard. RX/TX is working, bootwait is active, secure boot is not enabled. SSH can be activated in the stock firmware, but it drops only to a limited shell . Installation Instructions: black_small_square obtain serial access black_small_square stop auto boot black_small_square tftpboot the initramfs image (serverip is set to 192.168.99.8 in uboot) black_small_square bootm black_small_square copy openwrt-ipq807x-generic-edimax_cax1800-squashfs-nand-factory.ubi to the device black_small_square write the image to the NAND: black_small_square cat /proc/mtd and look for rootfs partition (should be mtd0) black_small_square ubiformat /dev/mtd0 -f -y openwrt-ipq807x-generic-edimax_cax1800-squashfs- nand-factory.ubi black_small_square reboot Note: Device is not using dual partitioning (NAND contains other partitions with different manufacture data etc.) Draytek VigorAP 960C and Lancom LW-600 both look similar, but I haven't checked them. Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
2022-01-01 22:17:51 +00:00
edimax,cax1800)
idx="$(find_mtd_index 0:appsblenv)"
[ -n "$idx" ] && \
ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x10000" "0x20000"
;;
ipq807x: add support for Linksys MX4200 V1 and V2 Linksys MX4200 is a 802.11ax Tri-band router/AP. Specifications: * CPU: Qualcomm IPQ8174 Quad core Cortex-A53 1.4GHz * RAM: 512MB of DDR3 * Storage: 512Mb NAND * Ethernet: 4x1G RJ45 ports (QCA8075) * WLAN: * 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate * 5GHz: Qualcomm QCN5054 2x2@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate * 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate * LED-s: * RGB system led * Buttons: 1x Soft reset 1x WPS * Power: 12V DC Jack Installation instructions: Open Linksys Web UI - http://192.168.1.1/ca or http://10.65.1.1/ca depending on your setup. Login with your admin password. The default password can be found on a sticker under the device. To enter into the support mode, click on the “CA” link and the bottom of the page. Open the “Connectivity” menu and upload the squash-factory image with the “Choose file” button. Click start. Ignore all the prompts and warnings by click “yes” in all the popups. The Wifi radios are turned off by default. To configure the router, you will need to connect your computer to the LAN port of the device. Then you would need to write openwrt to the other partition for it to work - First Check booted partition fw_printenv -n boot_part - Then install Openwrt to the other partition if booted in slot 1: mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4200v(X)-squashfs-factory.bin alt_kernel - If in slot 2: mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4200v(X)-squashfs-factory.bin kernel Replace (X) with your model version either 1 or 2 Signed-off-by: Mohammad Sayful Islam <sayf.mohammad01@gmail.com> Reviewed-by: Robert Marko <robimarko@gmail.com>
2024-01-03 07:54:16 +00:00
linksys,mx4200v1|\
qualcommax: ipq807x: add support for Linksys MX5300 Hardware specification: ======== SoC: Qualcomm IPQ8072A Flash: 512MB (Winbond W29N04GZBIBA) RAM: 1GB (2x Nanya DDR3L NT5CC256M16ER-EK) Ethernet: 5x 10/100/1000Mbps (Qualcomm QCA8075) WiFi1: 5GHz ac 4x4 (Qualcomm QCA9984 + Skyworks SKY85746-11) - channels 100-169 WiFi2: 5GHz ax 4x4 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 36-64 WiFi3: 2.4GHz ax 4x4 (Qualcomm QCN5024 + Skyworks SKY8340-11) IoT: Bluetooth 5, Zigbee and Thread (Qualcomm QCA4024 + Skyworks SE2433T-R) IoT Flash: 4MB (Macronix MX25R3235F) RTC: ST M41T00S LED: 1x RGB status (NXP PCA9633) USB: 1x USB 3.0 Button: WPS, Reset Flash instructions: ======== 1. Manually upgrade firmware using openwrt-qualcommax-ipq807x-linksys_mx5300-squashfs-factory.bin image. More details can be found here: https://www.linksys.com/hk/support-article?articleNum=274497 After first boot check actual partition: - fw_printenv -n boot_part and install firmware on second partition using command in case of 2: - mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx5300-squashfs-factory.bin kernel and in case of 1: - mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx5300-squashfs-factory.bin alt_kernel 2. Installation using serial connection from OEM firmware (default login: root, password: admin): - fw_printenv -n boot_part In case of 2: - flash_erase /dev/mtd21 0 0 nandwrite -p /dev/mtd21 openwrt-qualcommax-ipq807x-linksys_mx5300-squashfs-factory.bin or in case of 1: - flash_erase /dev/mtd23 0 0 nandwrite -p /dev/mtd23 openwrt-qualcommax-ipq807x-linksys_mx5300-squashfs-factory.bin After first boot install firmware on second partition: - mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx5300-squashfs-factory.bin kernel or: - mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx5300-squashfs-factory.bin alt_kernel 3. Installation from initramfs image using USB FAT32 formatted drive: Stop u-boot and run: - usb start && fatload usb 0:1 $loadaddr openwrt-qualcommax-ipq807x-linksys_mx5300-initramfs-uImage.itb && bootm $loadaddr Write firmware to the flash from initramfs: - mtd -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx5300-squashfs-factory.bin kernel and: - mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx5300-squashfs-factory.bin alt_kernel 4. Back to the OEM firmware: - mtd -e kernel -n write FW_MX5300_1.1.9.200251_prod.img kernel and: - mtd -r -e alt_kernel -n write FW_MX5300_1.1.9.200251_prod.img alt_kernel 5. USB recovery: - fw_setenv usbimage 'openwrt-qualcommax-ipq807x-linksys_mx5300-initramfs-uImage.itb' fw_setenv bootusb 'usb start && fatload usb 0:1 $loadaddr $usbimage && bootm $loadaddr' fw_setenv bootcmd 'run bootusb; aq_load_fw && if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi' Notes: ======== IoT device is accesible over spi. Not yet supported. Signed-off-by: Paweł Owoc <frut3k7@gmail.com> Reviewed-by: Robert Marko <robimarko@gmail.com>
2023-11-24 21:15:44 +00:00
linksys,mx4200v2|\
linksys,mx5300)
ipq807x: add support for Linksys MX4200 V1 and V2 Linksys MX4200 is a 802.11ax Tri-band router/AP. Specifications: * CPU: Qualcomm IPQ8174 Quad core Cortex-A53 1.4GHz * RAM: 512MB of DDR3 * Storage: 512Mb NAND * Ethernet: 4x1G RJ45 ports (QCA8075) * WLAN: * 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate * 5GHz: Qualcomm QCN5054 2x2@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate * 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate * LED-s: * RGB system led * Buttons: 1x Soft reset 1x WPS * Power: 12V DC Jack Installation instructions: Open Linksys Web UI - http://192.168.1.1/ca or http://10.65.1.1/ca depending on your setup. Login with your admin password. The default password can be found on a sticker under the device. To enter into the support mode, click on the “CA” link and the bottom of the page. Open the “Connectivity” menu and upload the squash-factory image with the “Choose file” button. Click start. Ignore all the prompts and warnings by click “yes” in all the popups. The Wifi radios are turned off by default. To configure the router, you will need to connect your computer to the LAN port of the device. Then you would need to write openwrt to the other partition for it to work - First Check booted partition fw_printenv -n boot_part - Then install Openwrt to the other partition if booted in slot 1: mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4200v(X)-squashfs-factory.bin alt_kernel - If in slot 2: mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4200v(X)-squashfs-factory.bin kernel Replace (X) with your model version either 1 or 2 Signed-off-by: Mohammad Sayful Islam <sayf.mohammad01@gmail.com> Reviewed-by: Robert Marko <robimarko@gmail.com>
2024-01-03 07:54:16 +00:00
idx="$(find_mtd_index u_env)"
[ -n "$idx" ] && \
ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x40000" "0x20000" "2"
;;
ipq807x: add Redmi AX6 Redmi AX6 is a budget 802.11ax dual-band router/AP Specifications: * CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz * RAM: 512MB of DDR3 * Storage: 128MB NAND * Ethernet: 4x1G RJ45 ports (QCA8075) * WLAN: * 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate * 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate * LEDs: * System (Blue/Yellow) * Network (Blue/Yellow) *Buttons: 1x soft reset *Power: 12V DC jack Installation instructions: Obtaining SSH access is mandatory https://openwrt.org/inbox/toh/xiaomi/xiaomi_redmi_ax6_ax3000#ssh_access Installation is done by the ubiformat method, through SSH: 1. Open an SSH shell to the router 2. Copy the file openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi to the /tmp directory 3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1): nvram get flag_boot_rootfs 4. Find the rootfs and rootfs_1 mtd indexes respectively: cat /proc/mtd Please confirm if mtd12 and mtd13 are the correct indexes from above! 5. Use the command ubiformat to flash the opposite mtd with UBI image: If nvram get flag_boot_rootfs returned 0: ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit otherwise: ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit 6. Reboot the device by: reboot Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages. Continue in order to pernamently flash OpenWrt: 7. SSH into OpenWrt from one of the LAN ports 8. Copy the file openwrt-ipq807x-generic-redmi_ax6-squashfs-sysupgrade.bin to the /tmp directory 9. Sysupgrade the device: sysupgrade -n /tmp/openwrt-ipq807x-generic-redmi_ax6-squashfs-sysupgrade.bin Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired. Signed-off-by: Zhijun You <hujy652@gmail.com>
2022-01-01 22:12:51 +00:00
redmi,ax6|\
ipq807x: Add Xiaomi AX9000 Xiaomi AX9000 is a premium 802.11ax "tri"-band router/AP. Specifications: * CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz * RAM: 1024MB of DDR3 * Storage: 256MB of parallel NAND * Ethernet: * 4x1G RJ45 ports (QCA8075) with 1x status LED per port * 1x2.5G RJ45 port (QCA8081) with 1x status LED * WLAN: * PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT * 2.4GHz: Qualcomm QCN5024 4x4@40MHz 802.11b/g/n/ax 1147 Mbps PHY rate * 5.8GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402Mbps PHY rate * 5GHz: PCI based Qualcomm QCN9024 4x4@160MHz 802.11a/b/g/n/ac/ax 4804Mbps PHY rate * USB: 1x USB3.0 Type-A port * LED-s: * System (Blue and Yellow) * Network (Blue and Yellow) * RGB light bar on top in X shape * Buttons: * 1x Power switch * 1x Soft reset * 1x Mesh button * Power: 12V DC Jack Installation instructions: Obtaining SSH access is mandatory https://openwrt.org/inbox/toh/xiaomi/ax9000#obtain_ssh_access Installation is done by the ubiformat method, through SSH: 1. Open an SSH shell to the router 2. Copy the file openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi to the /tmp directory 3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1): nvram get flag_boot_rootfs 4. Find the rootfs and rootfs_1 mtd indexes respectively: cat /proc/mtd Please confirm if mtd21 and mtd22 are the correct indexes from above! 5. Use the command ubiformat to flash the opposite mtd with UBI image: If nvram get flag_boot_rootfs returned 0: ubiformat /dev/mtd22 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit otherwise: ubiformat /dev/mtd21 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit 6. Reboot the device by: reboot Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages. Continue in order to pernamently flash OpenWrt: 7. SSH into OpenWrt from one of the LAN ports 8. Copy the file openwrt-ipq807x-generic-xiaomi_ax9000-squashfs-sysupgrade.bin to the /tmp directory 9. Sysupgrade the device: sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-squashfs-sysupgrade.bin Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired. Signed-off-by: Robert Marko <robimarko@gmail.com>
2022-01-10 23:50:37 +00:00
xiaomi,ax3600|\
xiaomi,ax9000)
ipq807x: add Xiaomi AX3600 Xiaomi AX3600 is a budget 802.11ax dual-band router/AP. Specifications: * CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz * RAM: 512MB of DDR3 * Storage: 256MB of parallel NAND * Ethernet: 4x1G RJ45 ports (QCA8075) with 1x status LED per port * WLAN: * PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT * 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate * 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate * LED-s: * System (Blue and Yellow) * IoT (Blue) * Network (Blue and Yellow) * Buttons: 1x Soft reset * Power: 12V DC Jack Installation instructions: Obtaining SSH access is mandatory https://openwrt.org/inbox/toh/xiaomi/xiaomi_ax3600#obtain_ssh_access Installation is done by the ubiformat method, through SSH: 1. Open an SSH shell to the router 2. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi to the /tmp directory 3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1): nvram get flag_boot_rootfs 4. Find the rootfs and rootfs_1 mtd indexes respectively: cat /proc/mtd Please confirm if mtd12 and mtd13 are the correct indexes from above! 5. Use the command ubiformat to flash the opposite mtd with UBI image: If nvram get flag_boot_rootfs returned 0: ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit otherwise: ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit 6. Reboot the device by: reboot Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages. Continue in order to pernamently flash OpenWrt: 7. SSH into OpenWrt from one of the LAN ports 8. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin to the /tmp directory 9. Sysupgrade the device: sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Signed-off-by: Robert Marko <robimarko@gmail.com>
2021-05-19 19:04:43 +00:00
idx="$(find_mtd_index 0:appsblenv)"
[ -n "$idx" ] && \
ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x10000" "0x20000"
idx2="$(find_mtd_index bdata)"
[ -n "$idx2" ] && \
ubootenv_add_uci_sys_config "/dev/mtd$idx2" "0x0" "0x10000" "0x20000"
;;
ipq807x: add initial support for prpl Foundation Haze board Haze is prpl Foundation's reference board (WNC LVRP). Board info: - IPQ8072A SoC - 2 GiB RAM - 4 GiB eMMC - 8MiB SPI NOR (MX25U6435F) - 3x 1GigE ports (QCA8075) - 1x 10GigE port (AQR113C) - 1x SFP cage - WiFi 6GHz 160MHz (QCN9074) - WiFi 5GHz 80+80MHz (QCN5054) - WiFi 2.4G (QCN5024) - ARM Standard 20-pin 2.54mm/0.1" JTAG (1V8 !!!) - Bluetooth v5.0 + EDR with integrated Class 1 PA (CYW20704) - 1x M.2 B-key socket with PCIe 3.0 - 1x USB 3.0 port - UART marked J6 is 4-pin 2.54mm/0.1" connector 3V3(arrow),RX,TX,GND (115200 8N1) - Reset and WPS buttons Flashing instructions: 1. From U-Boot boot OpenWrt using initramfs image: IPQ807x# tftpboot openwrt-ipq807x-generic-prpl_haze-initramfs-uImage.itb && bootm 2. In OpenWrt running from initramfs execute sysupgrade: root@OpenWrt:/# sysupgrade -n /tmp/openwrt-ipq807x-generic-prpl_haze-squashfs-sysupgrade.bin Work in progress/known issues: * SFP feature not implemented/tested * M.2 feature not implemented/tested * Bluetooth feature not implemented/tested * 6GHz wireless should be working, but not tested * MAC address assigments for LAN interfaces Signed-off-by: Petr Štetiar <ynezz@true.cz>
2023-06-05 10:13:04 +00:00
prpl,haze)
mmcpart="$(find_mmc_part 0:APPSBLENV)"
[ -n "$mmcpart" ] && \
ubootenv_add_uci_config "$mmcpart" "0x0" "0x40000" "0x400" "0x100"
;;
ipq807x: add QNAP 301w QNAP 301w is a AX WIFI router with 4 1G and 2 10G ports. Specifications: • CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz • RAM: 1024MB of DDR3 • Storage: 4GB eMMC (contains kernel and rootfs) / 8MB NOR (contains art and u-boot-env) • Ethernet: 4x 1G RJ45 ports + 2 10G ports (Aquantia AQR113C) • WLAN: 2.4GHz: Qualcomm QCN5024 4x4 (40 MHz) 802.11b/g/n/ax 1174 Mbps PHY rate 5GHz: Qualcomm QCN5054 4x4 (80 MHz) or 2x2 (160 MHz) 802.11a/b/g/n/ac/ax 2402 PHY rate • LEDs: 7 x GPIO-controlled dual color LEDs + 2 GPIO-controlled single color LEDs • Buttons: 1x soft reset / 1x WPS • Power: 12V DC jack A poulated serial header is onboard. RX/TX is working, bootwait is active, secure boot is not enabled. SSH can be activated in the stock firmware, hold WPS button til the second beep (yes the router has a buzzer) SSH is available on port 22200, login with user admin and password "mac address of the router". Installation Instructions: • obtain serial access (https://openwrt.org/inbox/toh/qnap/301w#serial) • stop auto boot • setenv serverip 192.168.10.1 • setenv ipaddr 192.168.10.10 • tftpboot the initramfs image (openwrt-ipq807x-generic-qnap_301w-initramfs-fit-uImage.itb) • bootm • make sure that current_entry is set to "0": "fw_printenv -n current_entry" should be print "0". If not, do "fw_setenv current_entry 0" • copy openwrt-ipq807x-generic-qnap_301w-squashfs-sysupgrade.bin to the device to /tmp folder • sysupgrade -n /tmp/openwrt-ipq807x-generic-qnap_301w-squashfs-sysupgrade.bin this flashes openwrt to the first kernel and rootfs partition (mmcblk0p1 / mmcblk0p4) • reboot Note: this leaves the second kernel / rootfs parition untouched. So if you want to go back to stock, stop u-boot autoboot, "setenv current_entry 1" , "saveenv", "bootipq". Stock firmware should start from the second partition. Then do a firmwareupgrade in the stock gui, that should overwrite the openwrt in the first partitions Make 10G Aquantia phy's work: The aquantia phy's need a firmware to work. This can either be loaded in linux with a userspace tool or in u-boot. I was not successfull to load the firmware in linux (aq-fw-download) but luckily there is aq_load_fw available in u-boot. But first the right firmware needs to write to the 0:ETHPHYFW mtd partition (it is empty on my device) Grab the ethphy firmware image from: https://github.com/kirdesde/nbg7815_gpl/blob/master/target/linux/ipq/ipq807x_64/prebuilt_images/AQR_ethphyfw.mbn and scp that to openwrt. Check the 0:ETHPHYFW partition number: cat /proc/mtd|grep "0:ETHPHYFW", should be mtd10. Backup the 0:ETHPHYFW partition: dd if=/dev/mtd10 of=/tmp/ethphyfw.backup, scp ethphyfw.backup to a save place. Write the new firmware image to the 0:ETHPHYFW partition: "mtd erase /dev/mtd10", "mtd -n write AQR_ethphyfw.mbn /dev/mtd10". Reboot to u-boot. Check if aq_load_fw is working: "aq_load_fw 0", that checks the firmware and if successfull, loads iram and dram to one of the aquantia phy's. If that worked, add the aq_load_fw to the bootcmd: setenv bootcmd "aq_load_fw 0 && aq_load_fw 8 && bootipq" "saveenv" "reset" Board reboots and the firmware load to both phy's should start and then openwrt boots. Check if the 10G ports work. Note: lan port labeled "10G-2" is configured as WAN port as per default. All other port are in the br-lan. This can be changed in the network config. Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
2022-01-01 22:20:19 +00:00
qnap,301w)
idx="$(find_mtd_index 0:appsblenv)"
[ -n "$idx" ] && \
ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x20000" "0x20000" "1"
;;
ipq807x: add Xiaomi AX3600 Xiaomi AX3600 is a budget 802.11ax dual-band router/AP. Specifications: * CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz * RAM: 512MB of DDR3 * Storage: 256MB of parallel NAND * Ethernet: 4x1G RJ45 ports (QCA8075) with 1x status LED per port * WLAN: * PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT * 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate * 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate * LED-s: * System (Blue and Yellow) * IoT (Blue) * Network (Blue and Yellow) * Buttons: 1x Soft reset * Power: 12V DC Jack Installation instructions: Obtaining SSH access is mandatory https://openwrt.org/inbox/toh/xiaomi/xiaomi_ax3600#obtain_ssh_access Installation is done by the ubiformat method, through SSH: 1. Open an SSH shell to the router 2. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi to the /tmp directory 3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1): nvram get flag_boot_rootfs 4. Find the rootfs and rootfs_1 mtd indexes respectively: cat /proc/mtd Please confirm if mtd12 and mtd13 are the correct indexes from above! 5. Use the command ubiformat to flash the opposite mtd with UBI image: If nvram get flag_boot_rootfs returned 0: ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit otherwise: ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit 6. Reboot the device by: reboot Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages. Continue in order to pernamently flash OpenWrt: 7. SSH into OpenWrt from one of the LAN ports 8. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin to the /tmp directory 9. Sysupgrade the device: sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Signed-off-by: Robert Marko <robimarko@gmail.com>
2021-05-19 19:04:43 +00:00
esac
config_load ubootenv
config_foreach ubootenv_add_app_config
exit 0
Reference in New Issue Copy Permalink