openwrt/target/linux/ipq806x/base-files/lib/upgrade/platform.sh

64 lines
1.2 KiB
Bash
Raw Normal View History

PART_NAME=firmware
REQUIRE_IMAGE_METADATA=1
RAMFS_COPY_BIN='fw_printenv fw_setenv'
RAMFS_COPY_DATA='/etc/fw_env.config /var/lock/fw_printenv.lock'
platform_check_image() {
return 0;
}
platform_do_upgrade() {
case "$(board_name)" in
ipq806x: add support for ASRock G10 The ASRock G10 is a 2.4/5 GHz band 11ac "Gaming" router, based on Qualcomm IPQ8064. Specifications: SoC: Qualcomm IPQ8064 CPU: Dual-Core A15 @ (384 - 1,400 MHz, 2C2T) DRAM: 512 MiB (~467 MiB available) NAND: 128 MB (Micron MT29F1G08ABBEAH4) WLAN0: 4T4R 5 GHz Wlan (QCA9980) WLAN1: 4T4R 2.4 GHz Wlan (QCA9980) ETH: 5x 10/100/1000 Mbps Ethernet (QCA8337) INPUT: Reset Button, WPS 2.4G and WPS 5G Button LEDS: 1 multicolor status LED USB: 2x USB 3.0 Type-A POWER: 12VDC/3A AC Adapter + dedicated Power Switch UART: Setting is 115200-8-N-1. 1x4 .1" unpopulated header on the PCB (J6 - very tiny silkscreen next to TX). Pinout: 1. 3v3 (Square - best skipped!), 2. RX, 3. GND, 4. TX WARNING: The serial port needs a TTL/RS-232 3.3v level converter! (Depending on the serial adapter RX and TX might need to be swapped). Note about the IR-Remote: There's a 8-Bit MCU (SONIX SN8F25E21SG) which is controlling the IR-Remote and is fed by the IR-Photodiode. The SoC can talk to the device via I2C. The vendor's GPL archive comes with the source of the interface driver for this as a (character driver), the main control software is however a blob. Installation Instructions: 1. Download factory image to disk 2. Apply factory image via stock web-gui Back to stock: 1. Login to router via ssh 2. run "asrock_g10_back_to_factory" script from /sbin Notes: - If something goes wrong durring sysupgrade, router will go back to factory image. - Asrock G10 uses partition layout from smem. So partition layout can be normal or alternate. - 900-arm-add-cmdline-override.patch was copied from 102-powerpc-add-cmdline-override.patch from powerpc target. Knowledge about BOOTCONFIG partition was based on user "jmomo" post from old OpenWrt forum (Post #50): https://forum.archive.openwrt.org/viewtopic.php?id=65956&p=2 Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [bump to 5.4, add factory image, fix sysupgrade, convert partition layout to smem, remove ipq-wifi-asrock-g10 and use ART, minor fixes] Co-Authored-by: Pawel Dembicki <paweldembicki@gmail.com> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> Tested-by: Lukasz Ostapiuk <palibrzuch@gmail.com>
2019-10-11 22:49:15 +00:00
asrock,g10)
asrock_upgrade_prepare
nand_do_upgrade "$1"
;;
buffalo,wxr-2533dhp)
buffalo_upgrade_prepare_ubi
CI_ROOTPART="ubi_rootfs"
nand_do_upgrade "$1"
;;
ipq806x: add support for Compex WPQ864 Hardware highlights: - SoC: Qualcomm Atheros IPQ8064/5 ARM Dual Core CPU - RAM: (512MB or 1GB) DDR3 System Memory - Storage: 32MB NOR (Cypress S25FL256S1) 256MB NAND (Micron MT29F2G08ABBEAH4) - Ethernet: 5 x 1G via QCA8337N - USB: 1 x USB 2.0/3.0 + 1 x USB 2.0 on mini PCIe3 socket - PCIe: 3x mini PCIe (third mini PCIE3 is PCIe/USB shared) - SIM Card Slot: 2 x Slot - Buttons: Reset Button - LEDs: 18x, 8x GPIO controllable - Buzzer The correct amount of RAM will be passed by the bootloader. In contrast to the documentation provided by Compex, the third PCIe doesn't use GPIO16 for PERST. Instead, GPIO3 is shared and used as PERST for PCIe0 and PCIe2. So far, no one was able to get USB 3.0 working with the 1GB RAM version, while it works fine for my 512MB version. Since USB 3.0 doesn't work with the Compex firmware for the 1G variant either, it could be a hardware issue with these boards. OpenWrt will be installed to the NAND flash. Make sure to have a full working image on the NOR flash. It will be the backup in case anything goes wrong. It has been observed that an image loaded via tftpboot might have bitflips. Hence the extra step to create a crc32 checksum to allow to compare the checksum with the one from the source file prior to flashing. In all cases it is necessary to set the following u-boot parameter to an empty (whitespace) value, to ensure that the chosen bootargs of the dts isn't overwritten or set to bogus - not working - values: (IPQ) # set bootargs " " (IPQ) # set fsbootargs " " (IPQ) # saveenv The sysupgrade image can be installed directly on flash using u-boot (put jumper in JP13 (leave JP9 open) to boot from nand): (IPQ) # set serverip 192.168.1.20 (IPQ) # set ipaddr 192.168.1.1 (IPQ) # tftpboot 0x42000000 openwrt-ipq806x-compex_wpq864-squashfs-nand-factory.bin (IPQ) # crc32 0x42000000 $filesize (IPQ) # nand erase 0x1340000 0x4000000 (IPQ) # nand write 0x42000000 0x1340000 $filesize The initramfs image can be started using: (IPQ) # set fdt_high 0x48000000 (IPQ) # tftpboot 0x44000000 openwrt-ipq806x-compex_wpq864-initramfs-fit-uImage.itb (IPQ) # bootm 0x44000000 Signed-off-by: Christian Mehlis <christian@m3hlis.de> Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-30 08:51:54 +00:00
compex,wpq864|\
netgear,d7800 |\
netgear,r7500 |\
netgear,r7500v2 |\
netgear,r7800 |\
qcom,ipq8064-ap148 |\
qcom,ipq8064-ap161)
nand_do_upgrade "$1"
;;
ipq806x: add Edgecore ECW5410 support This patch adds support for the Edgecore ECW5410 indoor AP. Specification: - SoC: Qualcomm Atheros IPQ8068 ARMv7 2x Cortex A-15 - RAM: 256MB(225 usable) DDR3 - NOR Flash: 16MB SPI NOR - NAND Flash: 128MB S34MS01G2 Parallel NAND - Ethernet: 2 x 1G via 2x AR8033 PHY-s connected directly to GMAC2 and GMAC3 via SGMII (802.3af POE IN on eth0) - USB: 1 x USB 3.0 SuperSpeed - WLAN: 2x QCA9994 AC Wawe 2 (1x 2GHz bgn, 1x 5GHz acn) - CC2540 BLE - UART console on RJ45 next to ethernet ports exposed. Its Cisco pin compatible, 115200 8n1 baud. Installation instructions: Through stock firmware or initramfs. 1.Connect to console 2. Login with root account, if password is unknown then interrupt the boot with f and reset it in failsafe. 3. Transfer factory image 4. Flash the image with ubiformat /dev/mtd1 -y -f <your factory image path> This will replace the rootfs2 with OpenWrt, if you are currently running from rootfs2 then simply change /dev/mtd1 to /dev/mtd0 Note Initramfs: 1. Connect to console 2. Transfer the image from TFTP server with tftpboot, or by using DHCP advertised image with dhcp command. 3. bootm 4. Run ubiformat /dev/mtd1 You need to interrupt the bootloader after rebooting and run: run altbootcmd This will switch your active rootfs partition to one you wrote to and boot from it. So if rootfs1 is active, then it will change it to rootfs2. This will format the rootfs2 partition, if your active partition is 2 then simply change /dev/mtd1 with /dev/mtd0 If you dont format the partition you will be writing too, then sysupgrade will find existing UBI rootfs and kernel volumes and update those. This will result in wrong ordering and OpenWrt will panic on boot. 5. Transfer sysupgrade image 6. Flash with sysupgrade -n. Note that sysupgrade will write the image to rootfs partition that is not currently in use. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2020-09-07 10:43:37 +00:00
edgecore,ecw5410)
part="$(awk -F 'ubi.mtd=' '{printf $2}' /proc/cmdline | sed -e 's/ .*$//')"
if [ "$part" = "rootfs1" ]; then
fw_setenv active 2 || exit 1
CI_UBIPART="rootfs2"
else
fw_setenv active 1 || exit 1
CI_UBIPART="rootfs1"
fi
nand_do_upgrade "$1"
;;
ipq806x: add support for Linksys EA7500 V1 This patch adds support for the Linksys EA7500 V1 router. Specification: - CPU: Qualcomm IPQ8064 - RAM: 256MB - Flash: NAND 128MB - WiFi: QCA9982 an+ac + QCA9983 bgn - Ethernet: 5 GBE Ports (WAN+ 4xLAN) (QCA8337) - USB: 1x USB 3.0 1x USB2.0 - Serial console: RJ-45 115200 8n1 (1V8 Voltage level) - 2 Buttons - 1 LED Known issues: - Some devices won't flash via web gui Installation: - Newer stock images doesn't allow to install custom firmware. - Please downgrade software to 1.1.2 version. Official firmware: https://downloads.linksys.com/downloads/firmware/FW_EA7500_1.1.2.172843_prod.gpg.img - Do it two times to downgrade all stored images. - Apply factory image via web-gui. Serial + TFTP method: - downgrade to 1.1.2 two times - connect ehternet and serial cable - set ip address of tftp server to 192.168.1.254 - put openwrt factory image to tftp folder and rename it to macan.bin - stop device while booting in u-boot - run command: "run flashimg" - run command: "setenv boot_part 1" - run command "saveenv" - reset Back to stock: - Please use old non-gpg image like this 1.1.2: https://downloads.linksys.com/downloads/firmware/FW_EA7500_1.1.2.172843_prod.img - ssh to router and copy image to tmp - use sysupgrade -n -F Tested by github users: @jack338c and @grzesiczek1 Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> [removed i2c4_pins, mdio0_pins, nand_pins, rgmii2_pins from DTSI] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-26 19:14:11 +00:00
linksys,ea7500-v1 |\
ipq806x: add support for Compex WPQ864 Hardware highlights: - SoC: Qualcomm Atheros IPQ8064/5 ARM Dual Core CPU - RAM: (512MB or 1GB) DDR3 System Memory - Storage: 32MB NOR (Cypress S25FL256S1) 256MB NAND (Micron MT29F2G08ABBEAH4) - Ethernet: 5 x 1G via QCA8337N - USB: 1 x USB 2.0/3.0 + 1 x USB 2.0 on mini PCIe3 socket - PCIe: 3x mini PCIe (third mini PCIE3 is PCIe/USB shared) - SIM Card Slot: 2 x Slot - Buttons: Reset Button - LEDs: 18x, 8x GPIO controllable - Buzzer The correct amount of RAM will be passed by the bootloader. In contrast to the documentation provided by Compex, the third PCIe doesn't use GPIO16 for PERST. Instead, GPIO3 is shared and used as PERST for PCIe0 and PCIe2. So far, no one was able to get USB 3.0 working with the 1GB RAM version, while it works fine for my 512MB version. Since USB 3.0 doesn't work with the Compex firmware for the 1G variant either, it could be a hardware issue with these boards. OpenWrt will be installed to the NAND flash. Make sure to have a full working image on the NOR flash. It will be the backup in case anything goes wrong. It has been observed that an image loaded via tftpboot might have bitflips. Hence the extra step to create a crc32 checksum to allow to compare the checksum with the one from the source file prior to flashing. In all cases it is necessary to set the following u-boot parameter to an empty (whitespace) value, to ensure that the chosen bootargs of the dts isn't overwritten or set to bogus - not working - values: (IPQ) # set bootargs " " (IPQ) # set fsbootargs " " (IPQ) # saveenv The sysupgrade image can be installed directly on flash using u-boot (put jumper in JP13 (leave JP9 open) to boot from nand): (IPQ) # set serverip 192.168.1.20 (IPQ) # set ipaddr 192.168.1.1 (IPQ) # tftpboot 0x42000000 openwrt-ipq806x-compex_wpq864-squashfs-nand-factory.bin (IPQ) # crc32 0x42000000 $filesize (IPQ) # nand erase 0x1340000 0x4000000 (IPQ) # nand write 0x42000000 0x1340000 $filesize The initramfs image can be started using: (IPQ) # set fdt_high 0x48000000 (IPQ) # tftpboot 0x44000000 openwrt-ipq806x-compex_wpq864-initramfs-fit-uImage.itb (IPQ) # bootm 0x44000000 Signed-off-by: Christian Mehlis <christian@m3hlis.de> Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-30 08:51:54 +00:00
linksys,ea8500)
platform_do_upgrade_linksys "$1"
ipq806x: add support for Compex WPQ864 Hardware highlights: - SoC: Qualcomm Atheros IPQ8064/5 ARM Dual Core CPU - RAM: (512MB or 1GB) DDR3 System Memory - Storage: 32MB NOR (Cypress S25FL256S1) 256MB NAND (Micron MT29F2G08ABBEAH4) - Ethernet: 5 x 1G via QCA8337N - USB: 1 x USB 2.0/3.0 + 1 x USB 2.0 on mini PCIe3 socket - PCIe: 3x mini PCIe (third mini PCIE3 is PCIe/USB shared) - SIM Card Slot: 2 x Slot - Buttons: Reset Button - LEDs: 18x, 8x GPIO controllable - Buzzer The correct amount of RAM will be passed by the bootloader. In contrast to the documentation provided by Compex, the third PCIe doesn't use GPIO16 for PERST. Instead, GPIO3 is shared and used as PERST for PCIe0 and PCIe2. So far, no one was able to get USB 3.0 working with the 1GB RAM version, while it works fine for my 512MB version. Since USB 3.0 doesn't work with the Compex firmware for the 1G variant either, it could be a hardware issue with these boards. OpenWrt will be installed to the NAND flash. Make sure to have a full working image on the NOR flash. It will be the backup in case anything goes wrong. It has been observed that an image loaded via tftpboot might have bitflips. Hence the extra step to create a crc32 checksum to allow to compare the checksum with the one from the source file prior to flashing. In all cases it is necessary to set the following u-boot parameter to an empty (whitespace) value, to ensure that the chosen bootargs of the dts isn't overwritten or set to bogus - not working - values: (IPQ) # set bootargs " " (IPQ) # set fsbootargs " " (IPQ) # saveenv The sysupgrade image can be installed directly on flash using u-boot (put jumper in JP13 (leave JP9 open) to boot from nand): (IPQ) # set serverip 192.168.1.20 (IPQ) # set ipaddr 192.168.1.1 (IPQ) # tftpboot 0x42000000 openwrt-ipq806x-compex_wpq864-squashfs-nand-factory.bin (IPQ) # crc32 0x42000000 $filesize (IPQ) # nand erase 0x1340000 0x4000000 (IPQ) # nand write 0x42000000 0x1340000 $filesize The initramfs image can be started using: (IPQ) # set fdt_high 0x48000000 (IPQ) # tftpboot 0x44000000 openwrt-ipq806x-compex_wpq864-initramfs-fit-uImage.itb (IPQ) # bootm 0x44000000 Signed-off-by: Christian Mehlis <christian@m3hlis.de> Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-30 08:51:54 +00:00
;;
tplink,c2600)
PART_NAME="os-image:rootfs"
MTD_CONFIG_ARGS="-s 0x200000"
default_do_upgrade "$1"
;;
tplink,vr2600v)
PART_NAME="kernel:rootfs"
MTD_CONFIG_ARGS="-s 0x200000"
default_do_upgrade "$1"
;;
zyxel,nbg6817)
zyxel_do_upgrade "$1"
;;
ipq806x: add ipq4019 fritz4040 support This patch adds support for AVM FRITZ!Box 4040. hardware highlights: SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB Nanya NT5CC128M16IP FLASH: 32 MiB MXIC MX25L25635FMI ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN) USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) 1 x 2.0 (via Synopsys DesignWare DWC3 controller in the SoC) WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: one WLAN and one WPS button LEDS: Power, WAN/Internet, WIFI, INFO (red and amber) and LAN. Serial: WARNING: The serial port needs a TTL/RS-232 v3.3 level converter! The Serial setting is 115200-8-N-1. The SoC's serial port is right next to the MXIC FLASH chip. The board has a unpopulated 1x4 0.1" header for it. Use a multimeter to figure out the pinout! This board currently needs an additional u-boot image in order to boot properly. Booting with EVA isn't possible ATM. Install Procedure: 0. It's highly recommended to connect to the serial port. The serial settings are listed above. 1. install a u-boot image for AVM Fritz!Box 4040 (see <https://github.com/chunkeey/FritzBox-4040-UBOOT/releases> and <https://github.com/chunkeey/FritzBox-4040-UBOOT/blob/master/upload-to-f4040.sh>) 2. upload the initramfs.itb image via tftp (u-boot listens to 192.168.1.1 - use binary transfer mode!) 3. connect to the FB4040 and use sysupgrade sysupgrade.bin to install the image. Works: - Switch and Ethernet (99%) - Buttons (WLAN, WPS) - FLASH (1 x 32MiB NOR Chip) - WLAN2G and WLAN5G - CPUFREQ scaling - PRNG - serial - Crypto Accelerator - sysupgrade (Read the flash instructions to avoid bricking) - full LEDE Install (Read the flash instructions to avoid bricking) - LEDs (Power, WAN, Info (red and amber), LAN) The LEDs are connected to the QCA8075 LED ports. The AR40xx driver contains a gpio-controller to handle these special "GPIOs". - USB Both 3.0 and 2.0 ports - many packages from other ARMv7 boards (This does include the RaspberryPi Model 2!) - ... Not planned: - WAN<->LAN short-cut - Qualcomm Secure Execution Environment - ... Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John Crispin <john@phrozen.org>
2017-03-14 16:04:28 +00:00
*)
default_do_upgrade "$1"
ipq806x: add ipq4019 fritz4040 support This patch adds support for AVM FRITZ!Box 4040. hardware highlights: SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB Nanya NT5CC128M16IP FLASH: 32 MiB MXIC MX25L25635FMI ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN) USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) 1 x 2.0 (via Synopsys DesignWare DWC3 controller in the SoC) WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: one WLAN and one WPS button LEDS: Power, WAN/Internet, WIFI, INFO (red and amber) and LAN. Serial: WARNING: The serial port needs a TTL/RS-232 v3.3 level converter! The Serial setting is 115200-8-N-1. The SoC's serial port is right next to the MXIC FLASH chip. The board has a unpopulated 1x4 0.1" header for it. Use a multimeter to figure out the pinout! This board currently needs an additional u-boot image in order to boot properly. Booting with EVA isn't possible ATM. Install Procedure: 0. It's highly recommended to connect to the serial port. The serial settings are listed above. 1. install a u-boot image for AVM Fritz!Box 4040 (see <https://github.com/chunkeey/FritzBox-4040-UBOOT/releases> and <https://github.com/chunkeey/FritzBox-4040-UBOOT/blob/master/upload-to-f4040.sh>) 2. upload the initramfs.itb image via tftp (u-boot listens to 192.168.1.1 - use binary transfer mode!) 3. connect to the FB4040 and use sysupgrade sysupgrade.bin to install the image. Works: - Switch and Ethernet (99%) - Buttons (WLAN, WPS) - FLASH (1 x 32MiB NOR Chip) - WLAN2G and WLAN5G - CPUFREQ scaling - PRNG - serial - Crypto Accelerator - sysupgrade (Read the flash instructions to avoid bricking) - full LEDE Install (Read the flash instructions to avoid bricking) - LEDs (Power, WAN, Info (red and amber), LAN) The LEDs are connected to the QCA8075 LED ports. The AR40xx driver contains a gpio-controller to handle these special "GPIOs". - USB Both 3.0 and 2.0 ports - many packages from other ARMv7 boards (This does include the RaspberryPi Model 2!) - ... Not planned: - WAN<->LAN short-cut - Qualcomm Secure Execution Environment - ... Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John Crispin <john@phrozen.org>
2017-03-14 16:04:28 +00:00
;;
esac
}