openwrt/target/linux/ramips/mt7621/config-5.10

293 lines
7.2 KiB
Plaintext
Raw Normal View History

CONFIG_ARCH_32BIT_OFF_T=y
CONFIG_ARCH_HIBERNATION_POSSIBLE=y
CONFIG_ARCH_MMAP_RND_BITS_MAX=15
CONFIG_ARCH_MMAP_RND_COMPAT_BITS_MAX=15
CONFIG_ARCH_NEEDS_CPU_IDLE_COUPLED=y
CONFIG_ARCH_SUSPEND_POSSIBLE=y
CONFIG_AT803X_PHY=y
CONFIG_BLK_MQ_PCI=y
CONFIG_BOARD_SCACHE=y
CONFIG_BOUNCE=y
CONFIG_CEVT_R4K=y
CONFIG_CLKDEV_LOOKUP=y
CONFIG_CLKSRC_MIPS_GIC=y
CONFIG_CLOCKSOURCE_WATCHDOG=y
CONFIG_CLONE_BACKWARDS=y
CONFIG_CMDLINE="rootfstype=squashfs,jffs2"
CONFIG_CMDLINE_BOOL=y
# CONFIG_CMDLINE_OVERRIDE is not set
CONFIG_COMMON_CLK=y
# CONFIG_COMMON_CLK_BOSTON is not set
CONFIG_COMPAT_32BIT_TIME=y
CONFIG_CPU_GENERIC_DUMP_TLB=y
CONFIG_CPU_HAS_DIEI=y
CONFIG_CPU_HAS_PREFETCH=y
CONFIG_CPU_HAS_RIXI=y
CONFIG_CPU_HAS_SYNC=y
CONFIG_CPU_IDLE=y
# CONFIG_CPU_IDLE_GOV_LADDER is not set
CONFIG_CPU_IDLE_GOV_TEO=y
CONFIG_CPU_MIPS32=y
# CONFIG_CPU_MIPS32_R1 is not set
CONFIG_CPU_MIPS32_R2=y
CONFIG_CPU_MIPSR2=y
CONFIG_CPU_MIPSR2_IRQ_EI=y
CONFIG_CPU_MIPSR2_IRQ_VI=y
CONFIG_CPU_NEEDS_NO_SMARTMIPS_OR_MICROMIPS=y
CONFIG_CPU_PM=y
CONFIG_CPU_R4K_CACHE_TLB=y
CONFIG_CPU_RMAP=y
CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y
CONFIG_CPU_SUPPORTS_HIGHMEM=y
CONFIG_CPU_SUPPORTS_MSA=y
CONFIG_CRC16=y
CONFIG_CRYPTO_ACOMP2=y
CONFIG_CRYPTO_BLAKE2S=y
CONFIG_CRYPTO_DEFLATE=y
CONFIG_CRYPTO_HASH_INFO=y
CONFIG_CRYPTO_LIB_BLAKE2S_GENERIC=y
CONFIG_CRYPTO_LIB_POLY1305_RSIZE=2
CONFIG_CRYPTO_LZO=y
CONFIG_CRYPTO_RNG2=y
CONFIG_CSRC_R4K=y
CONFIG_DEBUG_PINCTRL=y
CONFIG_DIMLIB=y
CONFIG_DMA_NONCOHERENT=y
# CONFIG_DTB_GNUBEE1 is not set
# CONFIG_DTB_GNUBEE2 is not set
CONFIG_DTB_RT_NONE=y
CONFIG_DTC=y
CONFIG_EARLY_PRINTK=y
CONFIG_FIXED_PHY=y
CONFIG_FW_LOADER_PAGED_BUF=y
CONFIG_GENERIC_ATOMIC64=y
CONFIG_GENERIC_CLOCKEVENTS=y
CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y
CONFIG_GENERIC_CMOS_UPDATE=y
CONFIG_GENERIC_CPU_AUTOPROBE=y
CONFIG_GENERIC_GETTIMEOFDAY=y
CONFIG_GENERIC_IOMAP=y
CONFIG_GENERIC_IRQ_CHIP=y
CONFIG_GENERIC_IRQ_EFFECTIVE_AFF_MASK=y
CONFIG_GENERIC_IRQ_SHOW=y
CONFIG_GENERIC_LIB_ASHLDI3=y
CONFIG_GENERIC_LIB_ASHRDI3=y
CONFIG_GENERIC_LIB_CMPDI2=y
CONFIG_GENERIC_LIB_LSHRDI3=y
CONFIG_GENERIC_LIB_UCMPDI2=y
CONFIG_GENERIC_PCI_IOMAP=y
CONFIG_GENERIC_PHY=y
CONFIG_GENERIC_PINCONF=y
CONFIG_GENERIC_SCHED_CLOCK=y
CONFIG_GENERIC_SMP_IDLE_THREAD=y
CONFIG_GENERIC_TIME_VSYSCALL=y
CONFIG_GLOB=y
CONFIG_GPIOLIB_IRQCHIP=y
CONFIG_GPIO_GENERIC=y
CONFIG_GPIO_MT7621=y
# CONFIG_GPIO_RALINK is not set
CONFIG_GPIO_WATCHDOG=y
# CONFIG_GPIO_WATCHDOG_ARCH_INITCALL is not set
CONFIG_GRO_CELLS=y
CONFIG_HANDLE_DOMAIN_IRQ=y
CONFIG_HARDWARE_WATCHPOINTS=y
CONFIG_HAS_DMA=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT_MAP=y
CONFIG_HIGHMEM=y
CONFIG_I2C=y
CONFIG_I2C_BOARDINFO=y
CONFIG_I2C_CHARDEV=y
ramips: add support for Tenbay T-MB5EU-V01 Hardware -------- MediaTek MT7621 SoC 256M DDR3 16MB BoHong SPI-NOR MediaTek MT7905+7975 2x2T2R DBDC bgnax / acax RGB LED WPS + RESET Button UART on compute module (silkscreened / 115200n8) The router itself is just a board with Power / USB / RJ-45 connectors and DC/DC converters. The SoC and WiFi components are on a daughterboard which connect using two M.2 connectors. The compute module has the model number "T-CB1800K-DM2 V02" printed on it. The main baord has "T-MB5EU V01" printed on it. This information might be useful, as it's highly likely either of these two will be reused in similar designs. The router itself is sold as Tenbay T-MB5EU directly from the OEM as well as "KuWFI AX1800 Smart WiFi 6 Eouter" on Amazon.de for ~50€ in a slightly different case. Installation ------------ A Tool for creating a factory image for the Vendor Web Interface can be found here: https://github.com/blocktrron/t-mb5eu-v01-factory-creator/ As the OEM Firmware is just a modified LEDE 17.01, you can also access failsafe mode via UART while the OS boots, by connecting to UART and pressing "f" when prompted. The Router is reachable at 192.168.1.1 via root without password. Transfer the OpenWrt sysupgrade image via scp and apply with sysupgrade using the -n and -F flags. Alternatively, the board can be flashed by attaching to the UART console, interrupting the boot process by keeping "0" pressed while attaching power. Serve the OpenWrt initramfs using a TFTP server with address 192.168.1.66. Rename the initramfs to ax1800.bin. Attach your TFTP server to one of the LAN ports. Execute the following commands. $ setenv ipaddr 192.168.1.67 $ setenv serverip 192.168.1.66 $ tftpboot 0x84000000 ax1800.bin $ bootm Wait for the device to boot. Then transfer the OpenWrt sysupgrade image to the device using SCP and apply sysupgrade. Signed-off-by: David Bauer <mail@david-bauer.net>
2021-05-06 16:07:18 +00:00
CONFIG_I2C_GPIO=y
CONFIG_I2C_MT7621=y
CONFIG_ICPLUS_PHY=y
CONFIG_INITRAMFS_SOURCE=""
CONFIG_IRQCHIP=y
CONFIG_IRQ_DOMAIN=y
CONFIG_IRQ_DOMAIN_HIERARCHY=y
CONFIG_IRQ_FORCED_THREADING=y
CONFIG_IRQ_MIPS_CPU=y
CONFIG_IRQ_WORK=y
# CONFIG_KERNEL_ZSTD is not set
CONFIG_LED_TRIGGER_PHY=y
CONFIG_LIBFDT=y
CONFIG_LOCK_DEBUGGING_SUPPORT=y
CONFIG_LZO_COMPRESS=y
CONFIG_LZO_DECOMPRESS=y
CONFIG_MDIO_BUS=y
CONFIG_MDIO_DEVICE=y
CONFIG_MEDIATEK_GE_PHY=y
CONFIG_MEMFD_CREATE=y
CONFIG_MFD_SYSCON=y
CONFIG_MIGRATION=y
CONFIG_MIKROTIK=y
CONFIG_MIKROTIK_RB_SYSFS=y
CONFIG_MIPS=y
CONFIG_MIPS_ASID_BITS=8
CONFIG_MIPS_ASID_SHIFT=0
CONFIG_MIPS_CBPF_JIT=y
CONFIG_MIPS_CLOCK_VSYSCALL=y
CONFIG_MIPS_CM=y
# CONFIG_MIPS_CMDLINE_BUILTIN_EXTEND is not set
# CONFIG_MIPS_CMDLINE_DTB_EXTEND is not set
# CONFIG_MIPS_CMDLINE_FROM_BOOTLOADER is not set
CONFIG_MIPS_CMDLINE_FROM_DTB=y
CONFIG_MIPS_CPC=y
CONFIG_MIPS_CPS=y
CONFIG_MIPS_CPS_CPUIDLE=y
# CONFIG_MIPS_CPS_NS16550_BOOL is not set
CONFIG_MIPS_CPS_PM=y
CONFIG_MIPS_CPU_SCACHE=y
# CONFIG_MIPS_ELF_APPENDED_DTB is not set
CONFIG_MIPS_GIC=y
CONFIG_MIPS_L1_CACHE_SHIFT=5
CONFIG_MIPS_LD_CAN_LINK_VDSO=y
CONFIG_MIPS_MT=y
CONFIG_MIPS_MT_FPAFF=y
CONFIG_MIPS_MT_SMP=y
# CONFIG_MIPS_NO_APPENDED_DTB is not set
CONFIG_MIPS_NR_CPU_NR_MAP=4
CONFIG_MIPS_PERF_SHARED_TC_COUNTERS=y
CONFIG_MIPS_RAW_APPENDED_DTB=y
CONFIG_MIPS_SPRAM=y
CONFIG_MODULES_USE_ELF_REL=y
CONFIG_MT7621_WDT=y
# CONFIG_MTD_CFI_INTELEXT is not set
CONFIG_MTD_CMDLINE_PARTS=y
CONFIG_MTD_NAND_CORE=y
CONFIG_MTD_NAND_ECC=y
CONFIG_MTD_NAND_ECC_SW_HAMMING=y
CONFIG_MTD_NAND_MT7621=y
CONFIG_MTD_NAND_MTK_BMT=y
CONFIG_MTD_PHYSMAP=y
CONFIG_MTD_RAW_NAND=y
CONFIG_MTD_ROUTERBOOT_PARTS=y
ramips: add support for Beeline SmartBox GIGA Beeline SmartBox GIGA is a wireless WiFi 5 router manufactured by Sercomm company. Device specification -------------------- SoC Type: MediaTek MT7621AT RAM: 256 MiB, Nanya NT5CC128M16JR-EK Flash: 128 MiB, Macronix MX30LF1G18AC Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2 Wireless 5 GHz (MT7613BE): a/n/ac, 2x2 Ethernet: 3 ports - 2xGbE (WAN, LAN1), 1xFE (LAN2) USB ports: 1xUSB3.0 Button: 1 button (Reset/WPS) PCB ID: DBE00B-1.6MM LEDs: 1 RGB LED Power: 12 VDC, 1.5 A Connector type: barrel Bootloader: U-Boot Installation ----------------- 1. Downgrade stock (Beeline) firmware to v.1.0.02; 2. Give factory OpenWrt image a shorter name, e.g. 1001.img; 3. Upload and update the firmware via the original web interface. Remark: You might need make the 3rd step twice if your running firmware is booted from the Slot 1 (Sercomm0 bootflag). The stock firmware reverses the bootflag (Sercomm0 / Sercomm1) on each firmware update. Revert to stock --------------- 1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 2. Optional: Update with any stock (Beeline) firmware if you want to overwrite OpenWrt in Slot 0 completely. MAC Addresses ------------- +-----+-----------+---------+ | use | address | example | +-----+-----------+---------+ | LAN | label | *:16 | | WAN | label + 1 | *:17 | | 2g | label + 4 | *:1a | | 5g | label + 5 | *:1b | +-----+-----------+---------+ The label MAC address was found in Factory 0x21000 Notes ----- 1. The following scripts are required for the build: sercomm-crypto.py - already exists in OpenWrt sercomm-partition-tag.py - already exists in OpenWrt sercomm-payload.py - already exists in OpenWrt sercomm-pid.py - new, the part of this pull request sercomm-kernel-header.py - new, the part of this pull request 2. This device (same as other Sercomm S2,S3-based devices) requires special LZMA and LOADADDR settings for successful boot: LZMA_TEXT_START=0x82800000 KERNEL_LOADADDR=0x81001000 LOADADDR=0x80001000 3. This device (same as several other Sercomm-based devices - Beeline, Netgear, Etisalat, Rostelecom) has partition map (mtd1) containing real partition offsets, which may differ from device to device depending on the number and location of bad blocks on NAND. "fixed-partitions" is used if the partition map is not found or corrupted. This behavour (it's the same as on stock firmware) is provided by MTD_SERCOMM_PARTS module. Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2022-03-18 18:09:45 +00:00
CONFIG_MTD_SERCOMM_PARTS=y
CONFIG_MTD_SPI_NOR=y
CONFIG_MTD_SPI_NOR_USE_VARIABLE_ERASE=y
CONFIG_MTD_SPLIT_FIT_FW=y
CONFIG_MTD_SPLIT_MINOR_FW=y
CONFIG_MTD_SPLIT_SEAMA_FW=y
CONFIG_MTD_SPLIT_TPLINK_FW=y
CONFIG_MTD_SPLIT_TRX_FW=y
CONFIG_MTD_SPLIT_UIMAGE_FW=y
CONFIG_MTD_UBI=y
CONFIG_MTD_UBI_BEB_LIMIT=20
CONFIG_MTD_UBI_BLOCK=y
CONFIG_MTD_UBI_WL_THRESHOLD=4096
CONFIG_MTD_VIRT_CONCAT=y
# CONFIG_MTK_HSDMA is not set
CONFIG_NEED_DMA_MAP_STATE=y
CONFIG_NET_DEVLINK=y
CONFIG_NET_DSA=y
CONFIG_NET_DSA_MT7530=y
CONFIG_NET_DSA_TAG_MTK=y
CONFIG_NET_FLOW_LIMIT=y
CONFIG_NET_MEDIATEK_SOC=y
CONFIG_NET_SWITCHDEV=y
CONFIG_NET_VENDOR_MEDIATEK=y
# CONFIG_NET_VENDOR_RALINK is not set
CONFIG_NO_HZ_COMMON=y
CONFIG_NO_HZ_IDLE=y
CONFIG_NR_CPUS=4
CONFIG_NVMEM=y
CONFIG_OF=y
CONFIG_OF_ADDRESS=y
CONFIG_OF_EARLY_FLATTREE=y
CONFIG_OF_FLATTREE=y
CONFIG_OF_GPIO=y
CONFIG_OF_IRQ=y
CONFIG_OF_KOBJ=y
CONFIG_OF_MDIO=y
CONFIG_OF_NET=y
CONFIG_PADATA=y
CONFIG_PCI=y
CONFIG_PCI_DISABLE_COMMON_QUIRKS=y
CONFIG_PCI_DOMAINS=y
CONFIG_PCI_DOMAINS_GENERIC=y
CONFIG_PCI_DRIVERS_GENERIC=y
CONFIG_PCI_MT7621=y
CONFIG_PCI_MT7621_PHY=y
CONFIG_PERF_USE_VMALLOC=y
CONFIG_PGTABLE_LEVELS=2
CONFIG_PHYLIB=y
CONFIG_PHYLINK=y
# CONFIG_PHY_RALINK_USB is not set
CONFIG_PINCTRL=y
CONFIG_PINCTRL_AW9523=y
CONFIG_PINCTRL_RT2880=y
# CONFIG_PINCTRL_SINGLE is not set
CONFIG_PINCTRL_SX150X=y
CONFIG_POWER_RESET=y
CONFIG_POWER_RESET_GPIO=y
CONFIG_POWER_SUPPLY=y
CONFIG_QUEUED_RWLOCKS=y
CONFIG_QUEUED_SPINLOCKS=y
CONFIG_RALINK=y
# CONFIG_RALINK_WDT is not set
CONFIG_RATIONAL=y
CONFIG_REGMAP=y
CONFIG_REGMAP_MMIO=y
CONFIG_REGULATOR=y
CONFIG_REGULATOR_FIXED_VOLTAGE=y
CONFIG_RESET_CONTROLLER=y
CONFIG_RFS_ACCEL=y
CONFIG_RPS=y
CONFIG_RTC_CLASS=y
CONFIG_RTC_DRV_BQ32K=y
CONFIG_RTC_DRV_PCF8563=y
CONFIG_RTC_I2C_AND_SPI=y
CONFIG_RTC_MC146818_LIB=y
CONFIG_SCHED_SMT=y
CONFIG_SERIAL_8250_NR_UARTS=3
CONFIG_SERIAL_8250_RUNTIME_UARTS=3
CONFIG_SERIAL_MCTRL_GPIO=y
CONFIG_SERIAL_OF_PLATFORM=y
CONFIG_SGL_ALLOC=y
CONFIG_SMP=y
CONFIG_SMP_UP=y
CONFIG_SOC_BUS=y
# CONFIG_SOC_MT7620 is not set
CONFIG_SOC_MT7621=y
# CONFIG_SOC_RT288X is not set
# CONFIG_SOC_RT305X is not set
# CONFIG_SOC_RT3883 is not set
CONFIG_SPI=y
CONFIG_SPI_MASTER=y
CONFIG_SPI_MEM=y
CONFIG_SPI_MT7621=y
# CONFIG_SPI_RT2880 is not set
CONFIG_SRCU=y
CONFIG_SWPHY=y
CONFIG_SYNC_R4K=y
CONFIG_SYSCTL_EXCEPTION_TRACE=y
CONFIG_SYS_HAS_CPU_MIPS32_R1=y
CONFIG_SYS_HAS_CPU_MIPS32_R2=y
CONFIG_SYS_HAS_EARLY_PRINTK=y
CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y
CONFIG_SYS_SUPPORTS_ARBIT_HZ=y
CONFIG_SYS_SUPPORTS_HIGHMEM=y
CONFIG_SYS_SUPPORTS_HOTPLUG_CPU=y
CONFIG_SYS_SUPPORTS_LITTLE_ENDIAN=y
CONFIG_SYS_SUPPORTS_MIPS16=y
CONFIG_SYS_SUPPORTS_MIPS_CPS=y
CONFIG_SYS_SUPPORTS_MULTITHREADING=y
CONFIG_SYS_SUPPORTS_SCHED_SMT=y
CONFIG_SYS_SUPPORTS_SMP=y
CONFIG_SYS_SUPPORTS_ZBOOT=y
CONFIG_TARGET_ISA_REV=2
CONFIG_TICK_CPU_ACCOUNTING=y
CONFIG_TIMER_OF=y
CONFIG_TIMER_PROBE=y
CONFIG_TREE_RCU=y
CONFIG_TREE_SRCU=y
CONFIG_UBIFS_FS=y
CONFIG_USB_SUPPORT=y
CONFIG_USE_OF=y
CONFIG_WATCHDOG_CORE=y
CONFIG_WEAK_ORDERING=y
CONFIG_WEAK_REORDERING_BEYOND_LLSC=y
CONFIG_XPS=y
CONFIG_ZLIB_DEFLATE=y
CONFIG_ZLIB_INFLATE=y