Replace usb_kill_urb() by usb_unlink_urb() in the timeout handler for
control URBs, as usb_kill_urb() may block and is not allowed to be
called in IRQ/bottom half contexts.
Fixes#4681
Lack of MSI-X support in DDE Linux causes a timeout when the Intel AX211
tries to call back into the driver while loading the PNVM file while
interrupts are still disabled.
With the patch picked up from QubesOS the card works on an X1 Nano G2:
5fcfe0f19e
Issue #4663
To prevent caching side-effects of USB DMA memory taken from the packet stream
all allocations of USB packets need to be on separated cachelines at least.
Fixgenodelabs/genode#4655
To complement the GPIO support allow for setting and reading input
pins. So far this is needed by drivers that attempt to perform I2C
bit-banging via GPIO pins.
Fixes#4624.
To enable other irqchip declarations beyond the lx_emul generic code base,
make the ARM specific initialization routine public.
Ref genodelabs/genode#4651
Prevents errors like follows.
/bin/bash: arch/arm64/crypto/poly1305-core.S: No such file or directory
make[4]: *** [.../genode/repos/dde_linux/lib/mk/spec/arm_64/wireguard_lx_inc_dirs.mk:17: arch/arm64/crypto/poly1305-core.S] Error 1
Reintroduce:
USB Attached SCSI devices might expose a bulk-only interface
as fall-back at interface 0 and alternate setting 0. This commit
allows for probing all alternate settings of the active interface
to be able to use such devices.
The configuration was extended so that in case the device interface
is known beforehand the driver can be configured accordingly.
Additionally:
Perform configuration reset upon sessions close in order to bring USB
device to a well defined state.
fixes#4494
Instead of allowing the client to set a caching attribute
in the io_mem() call of the device interface, which was
only used to decide in between of the memory being
write-combined or not, remove it from the API.
Instead use the information delivered by the devices ROM,
whether memory from a PCI BAR is prefetchable or not,
to decide whether it is mapped write-combined or not.
Ref genodelabs/genode#4578
* Remove wrapper for legacy x86 platform API
* Move PCI configuration space quirks to corresponding driver
(pc_usb_host_drv, pc_wifi_drv, pc_intel_fb_drv)
* Adapt driver test run-scripts to changed configuration
Ref genodelabs/genode#4578
Instead of having a generic "virt_qemu" board use "virt_qemu_<arch>" in
order to have a clean distinction between boards. Current supported
boards are "virt_qemu_arm_v7a", "virt_qemu_arm_v8a", and
"virt_qemu_riscv".
issue #4034
Skip SET_CONFIGURATION requests if the device already has the selected
config as active config. This workaround prevents issues with Linux
guests in VirtualBox and SDC-reader passthrough.
Thanks to Peter for the patch.
The commit introduces means to mark a task for destruction that is
removed on the next scheduling cycle. This fixes stack leakage from
dynamic kworker tasks.
Issue #4575.
* Move common SMP and NO_HZ_IDLE variables and functions into
generic lx_emul shadow implementations, and integrate them
into the common lx_emul import rules
* Enable SMP and NO_HZ_IDLE within virt_linux kernel configuration
* Adapt pc drivers and wireguard accordingly
* Use original Linux softirq implementation in wireguard
* Remove erroneous softirq shadow implementation
Ref genodelabs/genode#4540
Ref genodelabs/genode#4562
Enables symetric-multi-processor support in the Linux kernel configuration
used as base for the driver ports for PC. This is done to be compliant with
common usage of x86 drivers today.
Moreover, this commit uses the original kernel source for softirq/tasklet
implementation to get rid of the insufficient shadow implementation
in the lx_emul sources.
Ref genodelabs/genode#4562
Prepare shadow implementations in spinlocks, pagetable defines,
and irq_stack assembler macros to be able to enable SMP on x86/PC.
Ref genodelabs/genode#4562
Use common implementation used by wifi and (not merged) audio driver.
Avoid usage of lib/delay.c since lpj and loop_for_jiffies are not calibrated
for the ported drivers as done on native Linux during boot and leads to wrong
delays for usb and intel_fb.
Issue #4540
Adhere to include/linux/rcutiny.h behaviour, which sets the max timeout
for rcu_needs_cpu. Without the commit, in the most cases the timeout value
is zero (or random since the pointer is on stack uninitialized), which leads
to programming very short timeouts again and again, making the system never
idle.
Issue #4540
Querying the RFKILL state led to execution of the Lx_kit::scheduler by
the pthread running the wpa_supplicant. As this may not happen the
RFKILL state is now solely managed by the driver and only the cached
state is read by the supplicant.
Fixes#4537.
As accommodating the session component object is already taken care of
be the root component implementation, remove the remaining redundant
checks.
Fixes#4521.
Instead of allocating the stack via 'kmalloc' point it to the actual
stack used by the task. This addresses issues with the USB
host-controller driver where sometimes hub port enumeration is not
working.
Fixes#4522.
We locally disable 'address-of-packed-member' warnings because GCC complained
about possible alignment issues when returning a reference to a packed member
as naturally aligned pointer (for some reason only on arm_v8a). We know that
the member is aligned to NETDEV_ALIGN via __attribute__ and that the warning
is therefor unnecessary.
Ref #4519
We have to correct the CC_OPT_* variable for these files and used to do so via
phony pre-requisite for the corresponding object files because the correction
had to take place after the variable initialization in
import-lx_emul_common.inc and before the creation of the object files. However,
this caused the objects to always rebuild.
This commit fixes this issue by using Make's feature of target-specific
variables instead. The drawback of this solution is that we can no longer
override CC_OPT_* with a modification of its original value but instead have to
override with a completely new value. This is because otherwise, Make would
either complain about recursive assignment or produce an empty value.
Ref #4519
The strict conversion warnings were disabled during development when the
contrib code was still compiled with the wireguard lib. Now this isn't
necessary anymore as the contrib code is in the wireguard_lx_inc_dirs lib.
Ref #4520
With this commit, the WireGuard component exits with a descriptive uncaught
exception on invalid configurations or when the user attempts to re-configure
attributes that are not re-configurable (private_key, listen_port, interface).
This is particularly important when it comes to the not re-configurable private
key. If the component would just ignore the attempt to override the private
key, the user may come to believe that his old (potentially compromised)
private key is not in use anymore.
The fact that the component now exits instead shouldn't be a problem, as the
user would have to restart the component anyway in order to apply the new
attribute values.
The commit also extends the wg_reconfig run script to test that WireGuard
exits on the attempt to re-configure the private key.
Ref #4520
Support removing peers by removing them from the component configuration.
This commit also introduces the wg_reconfig run script that tests adding and
removing single peers.
Ref #4520
I used to set the peer flags to 2 when adding a peer but merely because I
observed that value in my reference Linux. I now found that the flag 1<<1 means
'WGPEER_F_REPLACE_ALLOWEDIPS' and is ignored whenever the peer is new. Anyway,
I keep setting the flag but with the clearer enum name because the wg tool is
doing it as well when adding new peers and we want to stay close to how the
original code interacts.
Ref #4520
The extra definition introduced by commit:
"lx_emul & arm: define ZERO_PAGE" re-defined the macro included
by a header of the contrib sources. This commit removes the
contrib header and defines thereby missing macros.
Fixes wrong atomic_*(ptr) usage with u32 pointer introduced by
commit "lx_emul: eliminate wrong include pathes". Atomic read or
write is nt needed in our case, we always schedule cooperatively.
Introduces the pkg/wireguard archive that depends on the new src/wireguard
archive and deploys one WireGuard component with an empty configuration (can
be configured by the user via a launcher, for instance).
Fixed#4519
Introduce an arch-specific wireguard lib that contains all code from the
former arch-specific target.mk files. This allows us to create a generic
target.mk that merely depends on the library and a dummy.cc file. The latter
ensures that building/linking of the target isn't skipped by the build system.
Ref #4519
The wireguard library's purpose is having a separate INC_DIR setting for the
files that need Linux include paths that would clash with Genode include paths.
Therefore, the name wireguard_lx_inc_dirs is more descriptive. Furthermore,
this allows us to create a new arch-specific wireguard lib in a future commit
in the course of preventing arch-specific target.mk's (a commonly used
approach in Genode).
Ref #4519
* Prevent page-faults when the active interface of a device got unset
during elimination of the device
* Resets devices, where a corresponding session got closed to
be re-useable when a new session gets opened
Ref #4512
With this commit, the Xoroshiro128+ PRNG in lx_emul/random.cc gets wrapped
by a new class that automatically re-seeds the PRNG with jitterentropy every
1024 * 1024 + random(0..4095) bytes of generated output.
Ref #4397
Both the Wifi driver and the WireGuard port used local implementations for
their source of randomness. Wifi used a Xoroshiro128+ PRNG for rapid generation
of random values but initialized this PRNG always with the same static seed
value. WireGuard, in contrast, requested each random byte directly from the
jitterentropy lib, which is considered to be very time intensive.
This commit removes the local variants of random.cc and introduces a new
centralized lx_emul/random.cc . The new variant combines the former approaches,
so, that jitterentropy is accessed only in order to generate a random seed for
a Xoroshiro128+ PRNG. Front-end requests for random values are then fulfilled
efficiently via the PRNG.
:Warning:
The output of the Xoroshiro128+ PRNG that is used in the new implementation of
the lx_emul randomness functions has known statistical problems (see
https://en.wikipedia.org/wiki/Xoroshiro128%2B#Statistical_Quality).
Furthermore, the integration of Xoroshir128+ with the lx_emul code was not
reviewed/audited for its security-related properties, so far, and has the
known deficiency of seeding the PRNG only once during initialization. Thus,
we strongly advise against the use of the lx_emul randomness functions for
security-critical purposes.
Ref #4397
A userland component that ports the Linux WireGuard kernel module (originally
from kernel version 5.14.21) and integrates it via a NIC session (public
network side) and an Uplink session (private network side). The
WireGuard-specific device configuration is done through the component
configuration. The port is done using lx_emul, lx_kit and the virt_linux
targets. The commit adds also 4 corresponding run scripts of which 3 are fully
automated of which 1 is added to the autopilot.
:Warning:
Although in principal functioning, the WireGuard port has not been exposed to a
sufficient amount of real-world testing, so far. Therefore, we strongly
recommend not to use it in any security-critical scenarios! There is no
guarantee that the port meets any of the security goals pursued by the
WireGuard protocol or other WireGuard implementations!
Ref #4397
The implementation was copied from the already existing LX-emul implementation
for x86 but the commit additionally page-aligns the array that serves as
backing store for the zero page as we assume this to be expected by the contrib
code. However, this commit doesn't apply the alignment also to the x86
implementation as we agreed, that this should be done in a separate commit.
Ref #4397
Since Linux does not use the arch-independent spinlock structs for ARM,
we must use different members when accessing the lock value.
genodelabs/genode#4499
