The Usb session allows for submitting packets even when the interface
in question is not yet enabled. Enabling an interface will configure
the udev members properly and is normally done implicitly during
processing of an 'ALT_SETTING' packet.
In case the interface was not enabled this leads to a page-fault in
the USB host-controller driver as 'ep' is NULL.
Fixes#3999.
* Remove SPEC declarations from mk/spec
* Remove all board-specific REQUIRE declaratiions left
* Replace [have_spec <board>] run-script declarations with have_board where necessary
* Remove addition of BOARD variable to SPECS in toplevel Makefile
* Move board-specific directories in base-hw out of specs
In order to perform a smooth transition from NIC drivers that act only as NIC
session clients to NIC drivers that act only as Uplink session clients, this
commit introduces an intermediate state in which all NIC drivers support both
modes. That said, a NIC drivers mode is now statically determined through a new
optional 'mode' attribute in the drivers <config> tag that can be set to either
'nic_server' (default value) or 'uplink_client'. Reconfiguring this attribute
at a driver doesn't have any effects. Whithout this attribute being set, all
NIC drivers will behave the same as they did before the commit. When set to
'uplink_client', however, instead of providing a Nic service, they request
an Uplink session whenever their network interface becomes "UP" and close the
session whenever their network interface becomes "DOWN".
Ref #3961
Let the NIC router provide an Uplink service besides the Nic service that it
already provided. Requests for an Uplink session towards the NIC router are
assigned to Domains using the same <policy> configuration tags that are used in
order to assign Nic session requests. The MAC addresses of Uplink session
components are _NOT_ considered during the allocation of MAC addresses for NIC
session components at the same Domain. The task of avoiding MAC address clashes
between Uplink session components and Nic session components is therefore left
to the integrator. Apart from that, Uplink session components are treated by
the NIC router like any other interface.
Ref #3961
Thise driver supports USB LTE modems for Huawais' ME906s through MBIM
and provides a traditional Nic session. The "control" interface is a
Terminal session, which can be used via libmbim/mbimcli.
issue #3822
- Vendor devices add addtional data to the config descriptor, read and
added to the usb session
- allow '0' configuration within the usb session
issue #3822
The usb_hid driver does not need to distinguish between
normal memory and DMA capable memory, since all requests are routed via the
USB raw session to the usb host driver. The default Malloc implementation
implements this distinction, however exposes restrictions on the size of
allocations. As seen now by several USB HID devices, the size of device
driver allocations depend on read out hardware features and can be
larger than we support with our specialized default Malloc implementation.
Since we don't need this functionality, switching to an well
tested allocator (Heap) which can cope with varying sizes of allocation,
we can mitigate the size restriction.
Fixes#3953
This prevents later file-descriptor shortage when opening files on
demand, which can't be reflected to the application in a sane manner.
The real fix is to open socket files not on libc level but on VFS level
only effectively consume one libc file descriptor for one socket.
* get rid of alarm abstraction
* get rid of Timeout::Time type
* get rid of pointer arguments
* get rid of _discard_timeout indirection
* get rid of 65th bit in stored time values
* get rid of Timeout_scheduler interface
* get rid of uninitialized deadlines
* get rid of default arguments
* get rid of Timeout::_periodic
* get rid of Timeout::Raw
* use list abstraction
* only one interface for timeout handlers
* rework locking scheme to be smp safe
* move all method definitions to CC file
* name mutexes more accurate
* fix when & how to set time-source timeout
* fix deadlocks
Fixes#3884
The current version of the driver leaves the screen in a black state
after a mode change, e.g., when connecting an external display.
With this patch, the framebuffer content is fetched for the entire
screen after a mode change. Thanks to Sebastian Sumpf for investigating.
Issue #3878
The combination of Net::Mac_address and
Genode::ascii_to(Net::Mac_address) required shaky quirks in several
places because GCC is not able to resolve the ascii_to overload if
base/xml_node.h was included to early. The current solution moves the
several ascii_to overloads "closer" to the Net types by putting them
into the Net namespace, where GCC reliably picks them up.
Hence, co-locating the ascii_to() utility with the overload type in the
same scope/namespace is good practice.
This patch removes the now obsolete <nic/xml_node.h> header file.
* On this platform there is no need to zero out the framebuffer
dataspace, which is already blanked by core
* But it might happen that the GUI server is sending a capture
event before the zero out happens. Thereby screen content can get
lost
Fix#3878
Follow-up commit to fix the old usb_drv. Under rpi one and the
same irq can be requested several times. Therefore, we've to track
the Irq_connection objects.
Ref #3865
The Lx_kit::Irq abstraction of DDE Linux was always using the very first
interrupt of a Platform::Device stored in it. Instead of handing over the
platform device it is much more flexible and sane to hand over the actual
interrupt capability.
Ref #3865
By now, the enumeration of peripheral interrupts on Raspberry Pi 1 was
different in between base-hw kernel and Fiasco.OC. Therefore, hacks were
needed in every driver to request the correct interrupt number dependent
on the kernel. Before reproducing the same in the platform driver for rpi,
we can more easily use the same enumeration with base-hw.
Ref #3864
This commit applies the transition from the "Input" session to the "Event"
session to the event-filtering mechansim. The functionality of the
input_filter is now provided by the event_filter. The event filter
requests only one "Event" session as destination for the filter result,
which is usually routed to the nitpicker GUI server. It provides an
"Event" service to which any number of event sources can connect.
The configuration of the filter chain remains almost the same. Only the
declaration of the <input> nodes is no longer needed. Instead, the
configuration must specify <policy> nodes, which define the mapping of
"Event" clients (event sources) to the inputs used in the filter chain.
The patch adjusts all uses of the nitpicker GUI server accordingly such
that the event filter reports events to nitpicker's event service
instead of having nitpicker request an "Input" session. This dissolves
the dependency of nitpicker from input drivers.
Issue #3827
This patch replaces the use of the "Framebuffer" session interface by
the new "Capture" session interface in all framebuffer drivers. Thanks
to this change, those drivers have become mere clients of the nitpicker
GUI server now, and are no longer critical for the liveliness of the GUI
server.
The patch touches the following areas:
- The actual driver components. The new versions of all drivers have
been tested on the respective hardware. Generally, the drivers
have become simpler.
- The drivers_interactive packages for various boards. The drivers
subsystem no longer provides a "Framebuffer" service but needs a
valid route to the "Capture" service provided by nitpicker.
- The driver manager of Sculpt OS.
- This patch changes the role of the test-framebuffer component from a
framebuffer client to a capture server so that drivers (capture clients)
can be directly connected to the test component without the nitpicker
server.
- Framebuffer driver no longer support the unbuffered mode.
- The fb_bench.run script is no longer very meaningful because it
interplays solely with nitpicker, not with the driver directly.
- All run scripts for graphical scenarios and the related depot
archives got adapted to the change.
Fixes#3813
Until now, Genode's framebuffer session interface was based on the
RGB565 pixel format. This patch changes the pixel format to 32-bit
XRGB where the X part is ignored. It adapts all graphical applications
and device drivers accordingly.
The patch also adjusts the users of the drivers_interactive packages,
assigning 64 MiB RAM and 1500 caps to the drivers subsystem, which is
sufficient for covering high resolutions at 32 bits per pixel and to
accommodate multi-component USB HID input stacks.
Fixes#3784
- Since Genode::strncpy is not 100% compatible with the POSIX
strncpy function, better use a distinct name.
- Remove bogus return value from the function, easing the potential
enforcement of mandatory return-value checks later.
Fixes#3752
Passing array of unsigned chars to Genode::log() function
makes it converted to void pointer, resulting in printing its address.
Wrapping this array into Genode::Cstring solves this problem
and makes it being printed properly as zero-terminaled string.
Signed-off-by: Oleg Girko <ol@infoserver.lv>
Fixes#3530
This patch extends the 'File_system::Status',
'File_system::Directory_entry', and the related 'Vfs' types with
the following additional information:
- Distinction between continuous and transactional files (Node_type)
(issue #3507)
- Readable, writeable, and executable attributes (Node_rwx),
replacing the former 'mode' bits
(issue #3030)
The types 'Node_rwx', 'Node_type' are defined twice,
once for the VFS (vfs/types.h) and once for the 'File_system'
session (file_system_session/file_system_session.h).
Similarly, there is a direct correspondance between
'Vfs::Directory_service::Dirent' and 'File_system::Directory_entry'.
This duplication of types follows the existing pattern of keeping the
VFS and file-system session independent from each other.
