The class Genode::Tss represents a 64-bit Task State Segment (TSS) as
specified by Intel SDM Vol. 3A, section 7.7.
The setup function sets the stack pointers for privilege levels 0-2 to
the kernel stack address. The load function loads the TSS segment
selector into the task register.
* Add isr.s assembler file:
The file declares an array of Interrupt Service Routines (ISR) to handle
the exception vectors from 0 to 19, see Intel SDM Vol. 3A, section
6.3.1.
* Add Idt class:
* The class Genode::Idt represents an Interrupt Descriptor Table as
specified by Intel SDM Vol. 3A, section 6.10.
* The setup function initializes the IDT with 20 entries using the ISR
array defined in the isr.s assembly file.
* Setup and load IDT in Genode::Cpu ctor:
The Idt::setup function is only executed once on the BSP.
* Declare ISRs for interrupts 20-255
* Set IDT size to 256
This patch contains the initial code needed to build and bootstrap the
base-hw kernel on x86 64-bit platforms. It gets stuck earlier
because the binary contains 64-bit instructions, but it is started in
32-bit mode. The initial setup of page tables and switch to long mode is
still missing from the crt0 code.
* Introduce hw-specific crt0 for core that calls e.g.: init_main_thread
* re-map core's main thread UTCB to fit the right context area location
* switch core's main thread's stack to fit the right context area location
Fix#1440
* enables world-switch using ARM virtualization extensions
* split TrustZone and virtualization extensions hardly from platforms,
where it is not used
* extend 'Vm_session' interface to enable configuration of guest-physical memory
* introduce VM destruction syscall
* add virtual machine monitor for hw_arndale that emulates a simplified version
of ARM's Versatile Express Cortex A15 board for a Linux guest OS
Fixes#1405
To enable support of hardware virtualization for ARM on the Arndale board,
the cpu needs to be prepared to enter the non-secure mode, as long as it does
not already run in it. Therefore, especially the interrupt controller and
some TrustZone specific system registers need to be prepared. Moreover,
the exception vector for the hypervisor needs to be set up properly, before
booting normally in the supervisor mode of the non-secure world.
Ref #1405
* name irq controller memory mapped I/O regions consistently
in board descriptions
* move irq controller and timer memory mapped I/O region descriptions
from cpu class to board class
* eliminate artificial distinction between flavors of ARM's GIC
* factor cpu local initialization out of ARM's GIC interface description,
which is needed if the GIC is initialized differently e.g. for TrustZone
Ref #1405
Setting the ACTLR.SMP bit also without SMP support fastens RAM access
significantly. A proper solution would implement SMP support which must enable
the bit anyway.
Fixes#1353
When building Genode for VEA9X4 as micro-hypervisor protected by the ARM
TrustZone hardware we ran into limitations regarding our basic daily
testing routines. The most significant is that, when speaking about RAM
partitioning, the only available options are to configure the whole SRAM
to be secure and the whole DDR-RAM to be non-secure or vice versa. The
SRAM however provides only 32 MB which isn't enough for both a
representative non-secure guest OS or a secure Genode that is still
capable of passing our basic tests. This initiated our decision to
remove the VEA9X4 TrustZone-support.
Fixes#1351
Kernel::Processor was a confusing remnant from the old scheme where we had a
Processor_driver (now Genode::Cpu) and a Processor (now Kernel::Cpu).
This commit also updates the in-code documentation and the variable and
function naming accordingly.
fix#1274
The run test 'hw_info' prints the content of the basic ARMv7 identification and
feature registers in a pretty readable format. It is a kernel-internal test
because many of these registers are restricted to privilege level 1 or higher.
fix#1278
Kernel tests are done by replacing the implementation of an otherwise
empty function 'Kernel::test' that gets called once at the primary CPU
as soon as all kernel initialization is done. To achieve this, the test
binary that implements 'Kernel::test' must be linked against the core
lib and must then replace the core binary when composing the boot image.
The latter can be done conveniently in a run script by setting the new
argument 'core_type' of the function 'build_boot_image' to the falue
'test'. If no kernel test is needed the argument does not have to be
given - it is set to 'core' by default which results in a "normal"
Genode image.
ref #1225
Previously, Idle_thread inherited from Thread which caused an extra
processor_pool.h and processor_pool.cc and also made class models for
processor and scheduling more complex. However, this inheritance makes
not much sense anyway as an idle context doesn't trigger most of the code
in Thread.
ref #1225
Previously, we did the protection-domain switches without a transitional
translation table that contains only global mappings. This was fine as long
as the CPU did no speculative memory accesses. However, to enabling branch
prediction triggers such accesses. Thus, if we don't want to invalidate
predictors on every context switch, we need to switch more carefully.
ref #474
The build config for core is now provided through libraries to enable
implicit config composition through specifiers and thereby avoid
consideration of inappropriate targets.
fix#1199
On ARM, when machine instructions get written into the data cache
(for example by a JIT compiler), one needs to make sure that the
instructions get written out to memory and read from memory into
the instruction cache before they get executed. This functionality
is usually provided by a kernel syscall and this patch adds a generic
interface for Genode applications to use it.
Fixes#1153.
This patch changes the top-level directory layout as a preparatory
step for improving the tools for managing 3rd-party source codes.
The rationale is described in the issue referenced below.
Issue #1082