By separating the session-interface concerns from the mechanics of the
dataspace creation, the code becomes simpler to follow, and the RAM
session can be more easily merged with the PD session in a subsequent
step.
Issue #2407
This patch allows core's 'Signal_transmitter' implementation to sidestep
the 'Env::Pd' interface and thereby adhere to a stricter layering within
core. The 'Signal_transmitter' now uses - on kernels that depend on it -
a dedicated (and fairly freestanding) RPC proxy mechanism for signal
deliver, instead of channeling signals through the 'Pd_session::submit'
RPC function.
Previously, the Genode::Timer::curr_time always used the
Timer_session::elapsed_ms RPC as back end. Now, Genode::Timer reads
this remote time only in a periodic fashion independently from the calls
to Genode::Timer::curr_time. If now one calls Genode::Timer::curr_time,
the function takes the last read remote time value and adapts it using
the timestamp difference since the remote-time read. The conversion
factor from timestamps to time is estimated on every remote-time read
using the last read remote-time value and the timestamp difference since
the last remote time read.
This commit also re-works the timeout test. The test now has two stages.
In the first stage, it tests fast polling of the
Genode::Timer::curr_time. This stage checks the error between locally
interpolated and timer-driver time as well as wether the locally
interpolated time is monotone and sufficiently homogeneous. In the
second stage several periodic and one-shot timeouts are scheduled at
once. This stage checks if the timeouts trigger sufficiently precise.
This commit adds the new Kernel::time syscall to base-hw. The syscall is
solely used by the Genode::Timer on base-hw as substitute for the
timestamp. This is because on ARM, the timestamp function uses the ARM
performance counter that stops counting when the WFI (wait for
interrupt) instruction is active. This instruction, however is used by
the base-hw idle contexts that get active when no user thread needs to
be scheduled. Thus, the ARM performance counter is not a good choice for
time interpolation and we use the kernel internal time instead.
With this commit, the timeout library becomes a basic library. That means
that it is linked against the LDSO which then provides it to the program it
serves. Furthermore, you can't use the timeout library anymore without the
LDSO because through the kernel-dependent LDSO make-files we can achieve a
kernel-dependent timeout implementation.
This commit introduces a structured Duration type that shall successively
replace the use of Microseconds, Milliseconds, and integer types for duration
values.
Open issues:
* The timeout test fails on Raspberry PI because of precision errors in the
first stage. However, this does not render the framework unusable in general
on the RPI but merely is an issue when speaking of microseconds precision.
* If we run on ARM with another Kernel than HW the timestamp speed may
continuously vary from almost 0 up to CPU speed. The Timer, however,
only uses interpolation if the timestamp speed remained stable (12.5%
tolerance) for at least 3 observation periods. Currently, one period is
100ms, so its 300ms. As long as this is not the case,
Timer_session::elapsed_ms is called instead.
Anyway, it might happen that the CPU load was stable for some time so
interpolation becomes active and now the timestamp speed drops. In the
worst case, we would now have 100ms of slowed down time. The bad thing
about it would be, that this also affects the timeout of the period.
Thus, it might "freeze" the local time for more than 100ms.
On the other hand, if the timestamp speed suddenly raises after some
stable time, interpolated time can get too fast. This would shorten the
period but nonetheless may result in drifting away into the far future.
Now we would have the problem that we can't deliver the real time
anymore until it has caught up because the output of Timer::curr_time
shall be monotone. So, effectively local time might "freeze" again for
more than 100ms.
It would be a solution to not use the Trace::timestamp on ARM w/o HW but
a function whose return value causes the Timer to never use
interpolation because of its stability policy.
Fixes#2400
With this, we get rid of platform specific timer interfaces. The new
Timer class does the same as the old Clock class and has a generic
interface. The old Timer class was merely used by the old Clock class.
Also, we get rid of having only one timer instance which we tell with
each method call for which CPU it shall be done. Instead now each Cpu
object has its own Timer member that knows the CPU it works for.
Also, rename all "tics" to "ticks".
Fixes#2347
Previously we did write the SPSR via an MSR instruction without
additional flags. Unfortunately, this tells the CPU to write the
register only partially. This often isn't a problem as the users PSR
reset value normally is conform to our expectations but in some cases
(e.g. PSR endianess bit on WandBoard core #4) the reset value is bad.
Thus, we have to add the CXSF flags (access Control + eXtension + Status
+ Flags) so the CPU overwrites the entire register.
Fixes#2254
This patch reduces the number of exception types by facilitating
globally defined exceptions for common usage patterns shared by most
services. In particular, RPC functions that demand a session-resource
upgrade not longer reflect this condition via a session-specific
exception but via the 'Out_of_ram' or 'Out_of_caps' types.
Furthermore, the 'Parent::Service_denied', 'Parent::Unavailable',
'Root::Invalid_args', 'Root::Unavailable', 'Service::Invalid_args',
'Service::Unavailable', and 'Local_service::Factory::Denied' types have
been replaced by the single 'Service_denied' exception type defined in
'session/session.h'.
This consolidation eases the error handling (there are fewer exceptions
to handle), alleviates the need to convert exceptions along the
session-creation call chain, and avoids possible aliasing problems
(catching the wrong type with the same name but living in a different
scope).
This patch mirrors the accounting and trading scheme that Genode employs
for physical memory to the accounting of capability allocations.
Capability quotas must now be explicitly assigned to subsystems by
specifying a 'caps=<amount>' attribute to init's start nodes.
Analogously to RAM quotas, cap quotas can be traded between clients and
servers as part of the session protocol. The capability budget of each
component is maintained by the component's corresponding PD session at
core.
At the current stage, the accounting is applied to RPC capabilities,
signal-context capabilities, and dataspace capabilities. Capabilities
that are dynamically allocated via core's CPU and TRACE service are not
yet covered. Also, the capabilities allocated by resource multiplexers
outside of core (like nitpicker) must be accounted by the respective
servers, which is not covered yet.
If a component runs out of capabilities, core's PD service prints a
warning to the log. To observe the consumption of capabilities per
component in detail, the PD service is equipped with a diagnostic
mode, which can be enabled via the 'diag' attribute in the target
node of init's routing rules. E.g., the following route enables the
diagnostic mode for the PD session of the "timer" component:
<default-route>
<service name="PD" unscoped_label="timer">
<parent diag="yes"/>
</service>
...
</default-route>
For subsystems based on a sub-init instance, init can be configured
to report the capability-quota information of its subsystems by
adding the attribute 'child_caps="yes"' to init's '<report>'
config node. Init's own capability quota can be reported by adding
the attribute 'init_caps="yes"'.
Fixes#2398
This patch replaces the 'Parent::Quota_exceeded',
'Service::Quota_exceeded', and 'Root::Quota_exceeded' exceptions
by the single 'Insufficient_ram_quota' exception type.
Furthermore, the 'Parent' interface distinguished now between
'Out_of_ram' (the child's RAM is exhausted) from
'Insufficient_ram_quota' (the child's RAM donation does not suffice to
establish the session).
This eliminates ambiguities and removes the need to convert exception
types along the path of the session creation.
Issue #2398
This patch upgrades the cap-space slab only if the kernel runs out of
entries, instead of consuming as much PD-session quota as possible.
Until now, the behavior worked well because the cap-space slab was the
only consumer of PD-session quota. However, once we start accounting all
PD session meta data - and eventually merging the PD and RAM services -
the aggressive scheme stands in the way.
Issue #2398
This commit moves the headers residing in `repos/base/include/spec/*/drivers`
to `repos/base/include/drivers/defs` or repos/base/include/drivers/uart`
respectively. The first one contains definitions about board-specific MMIO
iand RAM addresses, or IRQ lines. While the latter contains device driver
code for UART devices. Those definitions are used by driver implementations
in `repos/base-hw`, `repos/os`, and `repos/dde-linux`, which now need to
include them more explicitely.
This work is a step in the direction of reducing 'SPEC' identifiers overall.
Ref #2403
In order to deliver base-hw as a binary archive, we need to install the
bootstap.o file to bin/. Since bin/ is a global name space shared by all
kernels, this patch renames the object file to bootstap-hw.o and thereby
clarifies the association of the file with base-hw.
By installing the core object to bin/, we follow the same convention as
for regular binaries. This, in turn, enables us to ship core in a
regular binary archive. The patch also adjusts the run tool to pick up
the core object from bin/ for the final linking stage.
The size of the whole table and table entries were exchanged for PML4,
leading to out-of-bound accesses for addesses >= 2^39. Some constants
were lacking type suffixes causing integer overflows.
Added assertions to catch out-of-bound accesses early on.
Fixes#2210Fixes#2211
If we do the tics-to-us translation with one division and multiplication
over the whole argument, like before, we loose microseconds granularity
although the timer frequency allows for such granularity. Thus, we treat
the most significant half and the least significant half of the tics
value separate. Each half is shifted to the best bit position for the
translation, then translated, and then shifted back.
Ref #2347
Previously we pre-calculated the translation errors for the session
quota to make a discret check in the test. But since the order, in which
init childs get their CPU quota isn't always the same anymore (we should
have never made assumptions about that) the translation errors differ
from trial to trial. However, the errors are below 0.01% of the super
period. We now tolerate them in the run script.
Ref #2304
* Acknowledge receive of page-fault signal with ack_signal,
but restart thread execution separately
* use kill_signal_context when disolving a pager_object to prevent race
* Remove bureaucracy in form of Thread_event and Signal_ack_handler
* remove dead code in riscv, namely Thread_base definition
* translation_table_insertions function for ARM drops out,
which was overcautious
There was a race when the component entrypoint wanted to do
'wait_and_dispatch_one_signal'. In this function it raises a flag for
the signal proxy thread to notice that the entrypoint also wants to
block for signals. When the flag is set and the signal proxy wakes up
with a new signal, it tried to cancel the blocking of the entrypoint.
However, if the entrypoint had not reached the signal blocking at this
point, the cancel blocking failed without a solution. Now, the new
Kernel::cancel_next_signal_blocking call solves the problem by storing a
request to cancel the next signal blocking of a thread immediately
without blocking itself.
Ref #2284
There existed a race when 'wait_and_dispatch_one_signal' is called form
a RPC context, because the 'signal_proxy' or 'main' will block and the
signal semaphore, when the EP then calls 'wait_and_dispatch_one_signal',
the signal proxy is woken up ands sends an RPC to the EP, leading to a
dead lock if no further signal arrive, because the EP will then remain
blocked in the signal semaphore.
Therefore, for this case, the signal proxy will now perform a semaphore
up operation and does not perform an RPC if the EP is within
'wait_and_dispatch_one_signal'.
