openwrt/package/boot/uboot-envtools/files
Dirk Buchwalder 93610492b6 qualcommax: ipq60xx: add support for netgear wax214
Netgear WAX214 is a 802.11 ax dual-band AP
    with PoE. (similar to Engenius EWS357APV3)

    Specifications:

        •     CPU: Qualcomm IPQ6010 Quad core Cortex-A53
        •     RAM: 512MB of DDR3
        •     Storage: 128MB NAND (Macronix MX30UF1G18AC)
        •     Ethernet: 1x 1G RJ45 port (QCA8072) PoE
        •     WIFI:
              2.4GHz: Qualcomm QCN5022 2x2 802.11b/g/n/ax 574 Mbps PHY rate
              5GHz: Qualcomm QCN5052 2x2 802.11a/b/g/n/ac/ax 1201 PHY rate

        •     LEDs:
              4 x GPIO-controlled LEDs
                - 1 Power LED (orange)
                - 1 LAN LED (blue)
                - 1 WIFI 5g LED (blue)
                - 1 WIFI 2g LED (blue)
                black_small_square  Buttons: 1x soft reset
                black_small_square  Power: 12V DC jack or PoE (802.3af )

            An populated serial header is onboard, format is
             1.25mm 4p (DF13A-4P-1.25H)
            RX/TX is working, bootwait is active, secure boot is not
            enabled.

            The root password of the stock firmware is unknown,
            but failsafe mode can be entered to reset the password.

            Installation Instructions:

                - obtain serial access
                - stop auto boot (press "4", Entr boot command line
		  interface)
                - setenv active_fw 0 (to boot from the primary rootfs,
                  or set to 1 to boot from the secondary rootfs
                  partition)
                - saveenv

                - tftpboot the initramfs image
                - bootm

                - copy
		  openwrt-qualcommax-ipq60xx-netgear_wax214-squashfs-factory.ubi
                  to the device
                - write the image to the NAND:
                   - cat /proc/mtd and look for rootfs partition (should
		     be mtd11,
                     or mtd12 if you choose active_fw 1)
                   - ubiformat /dev/mtd11 -f -y
		     openwrt-qualcommax-ipq60xx-netgear_wax214-squashfs-factory.ubi
                - reboot

            Note: the firmware is senao-based. But I was unable to build
                  a valid senao-header into the image.
                  Maybe they changed the header format and senaoFW isn't
                  working any more.

Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
2024-03-05 06:34:35 +01:00
..
apm821xx apm821xx: MBL: make mtd chip work 2022-06-19 12:31:02 +02:00
ath79 ath79: add support for D-link DAP-1720 A1 2023-11-26 18:27:35 +01:00
cns3xxx uboot-envtools: drop shebang from uci-defaults and lib files 2021-04-10 15:18:14 +02:00
fw_printsys uboot-envtools: add wrapper scripts for alternate config 2021-04-08 09:20:59 +02:00
fw_setsys uboot-envtools: add wrapper scripts for alternate config 2021-04-08 09:20:59 +02:00
imx_cortexa7 uboot-envtools: imx: cortexa7: add TechNexion PICO-PI-IMX7D 2022-07-11 14:28:03 +02:00
imx_cortexa9 uboot-envtools: move imx to imx_cortexa9 2021-11-03 12:45:40 +01:00
ipq40xx ipq40xx: Add support Netgear LBR20 2024-02-23 19:46:23 +01:00
ipq806x ipq806x: add support for Extreme Networks AP3935 2023-10-05 00:56:57 +02:00
kirkwood kirkwood: add support for NETGEAR ReadyNAS Duo v2 2021-12-29 20:35:57 +01:00
lantiq uboot-envtools: drop shebang from uci-defaults and lib files 2021-04-10 15:18:14 +02:00
layerscape layerscape: remove Traverse LS1043 boards 2023-07-01 15:47:08 +02:00
mediatek_filogic uboot-envtools: replace use of platform_get_bootdev 2024-02-26 01:29:22 +00:00
mediatek_mt7622 uboot-envtools: replace use of platform_get_bootdev 2024-02-26 01:29:22 +00:00
mediatek_mt7623 uboot-envtools: replace use of platform_get_bootdev 2024-02-26 01:29:22 +00:00
mediatek_mt7629 mediatek: add support for Netgear EX6250v2 series 2023-07-01 14:42:11 +02:00
mpc85xx mpc85xx: add support for Enterasys WS-AP3715i 2023-04-08 14:41:01 +02:00
mvebu uboot-envtools: add settings for Synology DS213j 2023-11-20 13:40:17 +00:00
mxs uboot-envtools: drop shebang from uci-defaults and lib files 2021-04-10 15:18:14 +02:00
octeon octeon: n821: add Cisco vEdge 1000 base 2023-07-15 17:05:58 +02:00
oxnas uboot-envtools: oxnas: fix wrong eraseblock size for shuttle,kd20 2022-03-21 20:16:16 +00:00
pistachio uboot-envtools: drop shebang from uci-defaults and lib files 2021-04-10 15:18:14 +02:00
qoriq qoriq: add support for WatchGuard Firebox M300 2021-12-21 21:37:46 +02:00
qualcommax_ipq60xx qualcommax: ipq60xx: add support for netgear wax214 2024-03-05 06:34:35 +01:00
qualcommax_ipq807x qualcommax: ipq807x: add support for Linksys MX5300 2024-02-23 13:34:59 +01:00
ramips ramips: add support for Rostelecom RT-FE-1A 2023-12-06 00:12:56 +01:00
realtek uboot-envtools: add support for APRESIA ApresiaLightGS120GT-SS 2023-02-13 12:22:17 +01:00
uboot-envtools.sh uboot-envtools: add support for multiple config partitions 2021-04-08 09:20:59 +02:00