mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-28 17:48:58 +00:00
c6ddf8d502
Many changes were done in drivers/pinctrl/bcm/pinctrl-bcm2835.c between
5.4.171 and 5.4.179.
The following 3 patches do not apply any more:
* target/linux/bcm27xx/patches-5.4/950-0316-pinctrl-bcm2835-Add-support-for-BCM2711-pull-up-func.patch
This was already integrated in kernel v5.4-rc1, it was never needed.
* target/linux/bcm27xx/patches-5.4/950-0328-Revert-pinctrl-bcm2835-Pass-irqchip-when-adding-gpio.patch
* target/linux/bcm27xx/patches-5.4/950-0362-pinctrl-bcm2835-Change-init-order-for-gpio-hogs.patch
I think these were done to fix the problem which was really fixed in
commit 75278f1aff5e ("pinctrl: bcm2835: Change init order for gpio
hogs") from v5.4.175
target/linux/generic/backport-5.4/716-v5.5-net-sfp-move-fwnode-parsing-into-sfp-bus-layer.patch
Move fwnode_device_is_available to the same position as in kernel 5.10.
target/linux/layerscape/patches-5.4/302-dts-0083-arm64-ls1028a-qds-correct-bus-of-rtc.patch
Applied in commit 65816c1034769e714edb70f59a33bc5472d9e55f ("arm64: dts:
ls1028a-qds: move rtc node to the correct i2c bus")
Compile-tested: lantiq/xrx200, bcm27xx/bcm2710
Run-tested: lantiq/xrx200
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
|
||
|---|---|---|
| .. | ||
| 100-GPIO-add-named-gpio-exports.patch | ||
| 101-arm-dts-IPQ4019-add-SDHCI-VQMMC-LDO-node.patch | ||
| 102-ARM-dts-qcom-ipq4019-add-USB-devicetree-nodes.patch | ||
| 103-arm-dts-qcom-ipq4019-add-more-labels.patch | ||
| 104-clk-fix-apss-cpu-overclocking.patch | ||
| 300-clk-qcom-ipq4019-add-ess-reset.patch | ||
| 301-arm-compressed-add-appended-DTB-section.patch | ||
| 302-arm-compressed-set-ipq40xx-watchdog-to-allow-boot.patch | ||
| 400-mmc-sdhci-sdhci-msm-use-sdhci_set_clock-instead-of-s.patch | ||
| 702-dts-ipq4019-add-PHY-switch-nodes.patch | ||
| 703-net-IPQ4019-needs-rfs-vlan_tag-callbacks-in.patch | ||
| 705-net-add-qualcomm-ar40xx-phy.patch | ||
| 706-dt-bindings-net-add-QCA807x-PHY.patch | ||
| 707-net-phy-Add-Qualcom-QCA807x-driver.patch | ||
| 708-arm-dts-ipq4019-QCA807x-properties.patch | ||
| 710-net-add-qualcomm-essedma-ethernet-driver.patch | ||
| 711-dts-ipq4019-add-ethernet-essedma-node.patch | ||
| 850-soc-add-qualcomm-syscon.patch | ||
| 900-dts-ipq4019-ap-dk01.1.patch | ||
| 901-arm-boot-add-dts-files.patch | ||
| 902-dts-ipq4019-ap-dk04.1.patch | ||
| 997-device_tree_cmdline.patch | ||
| 0001-v5.7-ARM-qcom-Add-support-for-IPQ40xx.patch | ||
| 0002-01-v5.6-regulator-add-IPQ4019-SDHCI-VQMMC-LDO-driver.patch | ||
| 0002-02-v5.5-ARM-dts-qcom-ipq4019-Add-SDHCI-controller-node.patch | ||
| 0003-v5.6-ARM-dts-qcom-Add-nodes-for-SMP-boot-in-IPQ40xx.patch | ||
| 0003-v5.7-ARM-dts-qcom-add-gpio-ranges-property.patch | ||
| 0004-v5.8-ARM-dts-qcom-ipq4019-fix-high-resolution-timer.patch | ||
| 0005-01-v5.8-net-phy-mdio-add-IPQ4019-MDIO-driver.patch | ||
| 0005-02-v5.8-02-ARM-dts-qcom-ipq4019-add-MDIO-node.patch | ||
| 0006-v5.5-crypto-qce-add-CRYPTO_ALG_KERN_DRIVER_ONLY-flag.patch | ||
| 0007-v5.5-crypto-qce-switch-to-skcipher-API.patch | ||
| 0008-v5.6-crypto-qce-fix-ctr-aes-qce-block-chunk-sizes.patch | ||
| 0009-v5.6-crypto-qce-fix-xts-aes-qce-key-sizes.patch | ||
| 0010-v5.6-crypto-qce-save-a-sg-table-slot-for-result-buf.patch | ||
| 0011-v5.6-crypto-qce-update-the-skcipher-IV.patch | ||
| 0012-v5.6-crypto-qce-initialize-fallback-only-for-AES.patch | ||
| 0013-v5.6-crypto-qce-allow-building-only-hashes-ciphers.patch | ||
| 0014-v5.7-crypto-qce-use-cryptlen-when-adding-extra-sgl.patch | ||
| 0015-v5.7-crypto-qce-use-AES-fallback-for-small-requests.patch | ||
| 0016-v5.7-crypto-qce-handle-AES-XTS-cases-that-qce-fails.patch | ||
| 0017-v5.8-phy-add-driver-for-Qualcomm-IPQ40xx-USB-PHY.patch | ||
| 0018-v5.9-pinctrl-msm-open-drain.patch | ||
| 0019-v5.6-mtd-spi-nor-Add-support-for-mx25r3235f.patch | ||