mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-25 16:31:13 +00:00
635f111148
In ath79, for several SoCs the console bootargs are defined to the very same value in every device's DTS. Consolidate these definitions in the SoC dtsi files and drop further redundant definitions elsewhere. The only device without any bootargs set has been OpenMesh OM5P-AC V2. This will now inherit the setting from qca955x.dtsi Note that while this tidies up master a lot, it might develop into a frequent pitfall for backports. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
126 lines
2.0 KiB
Plaintext
126 lines
2.0 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
#include "qca953x.dtsi"
|
|
|
|
/ {
|
|
aliases {
|
|
led-boot = &led_link4;
|
|
led-failsafe = &led_link4;
|
|
led-running = &led_link4;
|
|
led-upgrade = &led_link4;
|
|
label-mac-device = &wmac;
|
|
};
|
|
|
|
leds: leds {
|
|
compatible = "gpio-leds";
|
|
|
|
link1 {
|
|
label = "tp-link:green:link1";
|
|
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
link2 {
|
|
label = "tp-link:green:link2";
|
|
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
link3 {
|
|
label = "tp-link:green:link3";
|
|
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led_link4: link4 {
|
|
label = "tp-link:green:link4";
|
|
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "Reset button";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&uart {
|
|
status = "okay";
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
|
|
num-cs = <1>;
|
|
|
|
flash@0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
uboot: partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x000000 0x020000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@20000 {
|
|
label = "partition-table";
|
|
reg = <0x020000 0x010000>;
|
|
read-only;
|
|
};
|
|
|
|
info: partition@30000 {
|
|
label = "info";
|
|
reg = <0x030000 0x010000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@40000 {
|
|
label = "firmware";
|
|
reg = <0x040000 0x780000>;
|
|
compatible = "tplink,firmware";
|
|
};
|
|
|
|
config: partition@7c0000 {
|
|
label = "config";
|
|
reg = <0x7c0000 0x030000>;
|
|
read-only;
|
|
};
|
|
|
|
art: partition@7f0000 {
|
|
label = "art";
|
|
reg = <0x7f0000 0x010000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
|
|
mtd-cal-data = <&art 0x1000>;
|
|
mtd-mac-address = <&info 0x8>;
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
phy-handle = <&swphy4>;
|
|
|
|
mtd-mac-address = <&info 0x8>;
|
|
};
|