Kevin Jilissen 4245adf4e0 realtek: add support for HPE 1920-8g-poe+ (65W) ... Hardware information: --------------------- - RTL8380 SoC - 8 Gigabit RJ45 PoE ports (built-in RTL8218B) - 2 SFP ports (built-in SerDes) - RJ45 RS232 port on front panel - 32 MiB NOR Flash - 128 MiB DDR3 DRAM - PT7A7514 watchdog - PoE chip - Fanless Known issues: --------------------- - PoE LEDs are uncontrolled. (Manual taken from f2f09bc) Booting initramfs image: ------------------------ - Prepare a FTP or TFTP server serving the OpenWrt initramfs image and connect the server to a switch port. - Connect to the console port of the device and enter the extended boot menu by typing Ctrl+B when prompted. - Choose the menu option "<3> Enter Ethernet SubMenu". - Set network parameters via the option "<5> Modify Ethernet Parameter". Enter the FTP/TFTP filename as "Load File Name" ("Target File Name" can be left blank, it is not required for booting from RAM). Note that the configuration is saved on flash, so it only needs to be done once. - Select "<1> Download Application Program To SDRAM And Run". Initial installation: --------------------- - Boot an initramfs image as described above, then use sysupgrade to install OpenWrt permanently. After initial installation, the bootloader needs to be configured to load the correct image file - Enter the extended boot menu again and choose "<4> File Control", then select "<2> Set Application File type". - Enter the number of the file "openwrt-kernel.bin" (should be 1), and use the option "<1> +Main" to select it as boot image. - Choose "<0> Exit To Main Menu" and then "<1> Boot System". NOTE: The bootloader on these devices can only boot from the VFS filesystem which normally spans most of the flash. With OpenWrt, only the first part of the firmware partition contains a valid filesystem, the rest is used for rootfs. As the bootloader does not know about this, you must not do any file operations in the bootloader, as this may corrupt the OpenWrt installation (selecting the boot image is an exception, as it only stores a flag in the bootloader data, but doesn't write to the filesystem). Example PoE config file (/etc/config/poe): --------------------- config global option budget '65' config port option enable '1' option id '1' option name 'lan8' option poe_plus '1' option priority '2' config port option enable '1' option id '2' option name 'lan7' option poe_plus '1' option priority '2' config port option enable '1' option id '3' option name 'lan6' option poe_plus '1' option priority '2' config port option enable '1' option id '4' option name 'lan5' option poe_plus '1' option priority '2' config port option enable '1' option id '5' option name 'lan4' option poe_plus '1' option priority '2' config port option enable '1' option id '6' option name 'lan3' option poe_plus '1' option priority '2' config port option enable '1' option id '7' option name 'lan2' option poe_plus '1' option priority '2' config port option enable '1' option id '8' option name 'lan1' option poe_plus '1' option priority '2' Signed-off-by: Kevin Jilissen <info@kevinjilissen.nl> (cherry picked from commit f4ee08677c)		2023-10-14 20:15:05 +02:00
..
rtl83xx_d-link_dgs-1210_common.dtsi
rtl83xx_d-link_dgs-1210_gpio.dtsi
rtl83xx_panasonic_mxxeg-pn28xx0k.dtsi	realtek: use generic earlycon setup on 5.15	2023-01-30 14:30:41 +01:00
rtl838x_hpe_1920.dtsi	realtek: use generic earlycon setup on 5.15	2023-01-30 14:30:41 +01:00
rtl838x.dtsi	realtek: use generic earlycon setup on 5.15	2023-01-30 14:30:41 +01:00
rtl839x_d-link_dgs-1210_gpio.dtsi
rtl839x.dtsi	realtek: use generic earlycon setup on 5.15	2023-01-30 14:30:41 +01:00
rtl930x.dtsi	realtek: use generic earlycon setup on 5.15	2023-01-30 14:30:41 +01:00
rtl931x.dtsi	realtek: fix dts whitespace	2023-02-09 03:03:52 +01:00
rtl8380_d-link_dgs-1210-10mp-f.dts	realtek: dgs-1210-10mp: update sfp phy-handle	2023-01-28 21:01:29 +01:00
rtl8380_engenius_ews2910p.dts
rtl8380_hpe_1920-8g-poe-65w.dts	realtek: add support for HPE 1920-8g-poe+ (65W)	2023-10-14 20:15:05 +02:00
rtl8380_hpe_1920-8g-poe-180w.dts	realtek: rename hpe,1920-8g-poe to match hardware	2023-10-14 20:14:51 +02:00
rtl8380_hpe_1920-8g.dts	realtek: add support for HPE 1920-8g-poe+	2023-08-09 22:14:12 +02:00
rtl8380_hpe_1920-8g.dtsi	realtek: add support for HPE 1920-8g-poe+	2023-08-09 22:14:12 +02:00
rtl8380_netgear_gigabit_1xx.dtsi
rtl8380_netgear_gigabit_3xx.dtsi
rtl8380_netgear_gigabit.dtsi
rtl8380_netgear_gs108t-v3.dts
rtl8380_netgear_gs110tpp-v1.dts
rtl8380_netgear_gs308t-v1.dts
rtl8380_netgear_gs310tp-v1.dts
rtl8380_panasonic_m8eg-pn28080k.dts
rtl8380_tplink_sg2xxx.dtsi
rtl8380_tplink_sg2008p-v1.dts
rtl8380_tplink_sg2210p-v3.dts
rtl8380_zyxel_gs1900-8.dts
rtl8380_zyxel_gs1900-8hp-v1.dts
rtl8380_zyxel_gs1900-8hp-v2.dts
rtl8380_zyxel_gs1900-10hp.dts
rtl8380_zyxel_gs1900.dtsi
rtl8382_allnet_all-sg8208m.dts
rtl8382_apresia_aplgs120gtss.dts	realtek: add support for APRESIA ApresiaLightGS120GT-SS	2023-02-13 12:22:17 +01:00
rtl8382_d-link_dgs-1210-10p.dts
rtl8382_d-link_dgs-1210-16.dts
rtl8382_d-link_dgs-1210-20.dts
rtl8382_d-link_dgs-1210-28_common.dtsi
rtl8382_d-link_dgs-1210-28.dts
rtl8382_d-link_dgs-1210-28mp-f.dts
rtl8382_hpe_1920-16g.dts
rtl8382_hpe_1920-24g.dts
rtl8382_hpe_1920.dtsi
rtl8382_inaba_aml2-17gp.dts
rtl8382_iodata_bsh-g24mb.dts	realtek: use generic earlycon setup on 5.15	2023-01-30 14:30:41 +01:00
rtl8382_panasonic_m16eg-pn28160k.dts
rtl8382_panasonic_m24eg-pn28240k.dts
rtl8382_zyxel_gs1900-16.dts
rtl8382_zyxel_gs1900-24-v1.dts
rtl8382_zyxel_gs1900-24e.dts
rtl8382_zyxel_gs1900-24hp-v1.dts
rtl8382_zyxel_gs1900-24hp-v2.dts
rtl8393_d-link_dgs-1210-52.dts
rtl8393_netgear_gs750e.dts	realtek: add support for Netgear GS750E	2023-01-13 22:28:36 +01:00
rtl8393_panasonic_m48eg-pn28480k.dts
rtl8393_tplink_sg2452p-v4.dts	realtek: use generic earlycon setup on 5.15	2023-01-30 14:30:41 +01:00
rtl8393_zyxel_gs1900-48.dts	realtek: fix dts whitespace	2023-02-09 03:03:52 +01:00
rtl9302_zyxel_xgs1250-12.dts	realtek: dsa: support active-high LEDs	2023-01-24 21:55:44 +01:00